arm64: dts: allwinner: h6: tanix-tx6: Enable eMMC
Subsystems (2)
Jernej Skrabec
maintainerv2 cover arm64: dts: allwinner: h6: tanix-tx6: Enable eMMC
Tanix TX6 box has a 32 GB eMMC module. With changes in this series, I get following figures with hdparm -tT:
/dev/mmcblk2:
Timing cached reads: 1638 MB in 2.00 seconds = 818.44 MB/sec
Timing buffered disk reads: 376 MB in 3.01 seconds = 124.74 MB/sec
First patch fixes regulator node names. Second patch sets proper power supplies to GPIO banks and third adds eMMC support.
Please take a look.
Best regards,
Jernej Skrabec
Changes from v1:
- added patch 1 (fixing regulator node names with "regulator-" prefix)
- fixed regulator node name in patch 2 (adding "regulator-" prefix)
Jernej Skrabec (3):
arm64: dts: allwinner: h6: tanix-tx6: Fix regulator node names
arm64: dts: allwinner: h6: tanix-tx6: Add PIO power supplies
arm64: dts: allwinner: h6: tanix-tx6: enable emmc
.../dts/allwinner/sun50i-h6-tanix-tx6.dts | 27 +++++++++++++++++-- 1 file changed, 25 insertions(+), 2 deletions(-)
Signature · 1 line
2.32.0
Jernej Skrabec
maintainerPATCH v2 1/3 arm64: dts: allwinner: h6: tanix-tx6: Fix regulator node names
Regulator node names don't reflect class of the device. Fix that by prefixing names with "regulator-".
--- arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts +2 -2
@@ -32,14 +32,14 @@ hdmi_con_in: endpoint { }; }; - reg_vcc3v3: vcc3v3 { + reg_vcc3v3: regulator-vcc3v3 { compatible = "regulator-fixed"; regulator-name = "vcc3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; - reg_vdd_cpu_gpu: vdd-cpu-gpu { + reg_vdd_cpu_gpu: regulator-vdd-cpu-gpu { compatible = "regulator-fixed"; regulator-name = "vdd-cpu-gpu"; regulator-min-microvolt = <1135000>;
Signature · 1 line
2.32.0
Jernej Skrabec
maintainerPATCH v2 2/3 arm64: dts: allwinner: h6: tanix-tx6: Add PIO power supplies
In reply to Jernej SkrabecWhile there is no publicly available schematic of this board, it's not hard to determine voltage of GPIO port C, D and G (only ones which can be set).
Port C and G are used for MMC/SDIO communication, so they use 1.8 V power supply. It's not clear if port D is even used, but if it is, it's pretty safe to assume it uses 3.3 V power supply. Value read from PIO Group Withstand Voltage Mode Select register from within pre-installed Android agrees with that assesment.
--- .../boot/dts/allwinner/sun50i-h6-tanix-tx6.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts +13 -0
@@ -32,6 +32,13 @@ hdmi_con_in: endpoint { }; }; + reg_vcc1v8: regulator-vcc1v8 { + compatible = "regulator-fixed"; + regulator-name = "vcc1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + reg_vcc3v3: regulator-vcc3v3 { compatible = "regulator-fixed"; regulator-name = "vcc3v3";
@@ -99,6 +106,12 @@ &ohci3 { status = "okay"; }; +&pio { + vcc-pc-supply = <®_vcc1v8>; + vcc-pd-supply = <®_vcc3v3>; + vcc-pg-supply = <®_vcc1v8>; +}; + &r_ir { linux,rc-map-name = "rc-tanix-tx5max"; status = "okay";
Signature · 1 line
2.32.0
Jernej Skrabec
maintainerPATCH v2 3/3 arm64: dts: allwinner: h6: tanix-tx6: enable emmc
In reply to Jernej SkrabecTanix TX6 has 32 GiB eMMC. Add a node for it.
--- arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts +10 -0
@@ -98,6 +98,16 @@ &mmc0 { status = "okay"; }; +&mmc2 { + vmmc-supply = <®_vcc3v3>; + vqmmc-supply = <®_vcc1v8>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + mmc-hs200-1_8v; + status = "okay"; +}; + &ohci0 { status = "okay"; };
Signature · 1 line
2.32.0
Maxime Ripard
AppliedQuoted 11 lines · Jernej Skrabec
Tanix TX6 box has a 32 GB eMMC module. With changes in this series, I get following figures with hdparm -tT:
/dev/mmcblk2:
Timing cached reads: 1638 MB in 2.00 seconds = 818.44 MB/sec
Timing buffered disk reads: 376 MB in 3.01 seconds = 124.74 MB/secFirst patch fixes regulator node names. Second patch sets proper power supplies to GPIO banks and third adds eMMC support.
Please take a look.
Applied all three, thanks
Maxime