Skip to contentSkip to conversation

configs: imx8mm_venice_defconfig: remove unused SPL features

PATCH New Tim Harvey 1 participant 9 messages Jul 27, 2021

Subsystems (2)
lore
Share & tools
lore

Tim Harvey

author
#0 lore raw

PATCH 1/9 configs: imx8mm_venice_defconfig: remove unused SPL features

remove unused SPL features to shink the size of the SPL which otherwise would no longer fit into IMX8M Mini OCRAM.

---
 configs/imx8mm_venice_defconfig | 2 --
 1 file changed, 2 deletions(-)
configs/imx8mm_venice_defconfig +0 -2
index 49affccec4..f1efdc60a4 100644
@@ -26,7 +26,6 @@ CONFIG_DISTRO_DEFAULTS=y
 CONFIG_FIT=y
 CONFIG_FIT_EXTERNAL_OFFSET=0x3000
 CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_LOAD_FIT_FULL=y
 CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
 CONFIG_OF_SYSTEM_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/imx8m/imximage-8mm-lpddr4.cfg"
@@ -36,7 +35,6 @@ CONFIG_PREBOOT="gsc wd-disable"
 CONFIG_BOARD_LATE_INIT=y
 CONFIG_SPL_SEPARATE_BSS=y
 CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_POWER_SUPPORT=y
 CONFIG_SPL_WATCHDOG_SUPPORT=y
 CONFIG_SYS_PROMPT="u-boot=> "
 # CONFIG_CMD_EXPORTENV is not set
Signature · 1 line
2.17.1
author
#1 lore raw

PATCH 2/9 arm: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS

The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12 is the power-enable to the TPS25821 Source controller and power switch responsible for monitoring the CC pins and enabling VBUS. Therefore GPIO1_12 must always be enabled and the vbus output enable from the IMX8MM can be ignored.

To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the TPS25821 and change the regulator output to GPIO1_10 which is unconnected.

---
 arch/arm/dts/imx8mm-venice-gw71xx.dtsi | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
arch/arm/dts/imx8mm-venice-gw71xx.dtsi +3 -2
index 905b68a3da..8e4a0ce997 100644
@@ -46,7 +46,7 @@
 		pinctrl-0 = <&pinctrl_reg_usb1_en>;
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg1_vbus";
-		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
@@ -156,7 +156,8 @@
 
 	pinctrl_reg_usb1_en: regusb1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x41
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10	0x41
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x141
 			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC	0x41
 		>;
 	};
Signature · 1 line
2.17.1
author
#2 lore raw

PATCH 3/9 arm: dts: imx8mm-venice-gw700x: fix fifo-depth phy props

In reply to Tim Harvey

Replace the deprecated 'tx-fifo-depth' and 'rx-fifo-depth' properties not supported by U-Boot drivers/net/phy/dp83867.c with the proper 'ti,fifo-depth' property.

---
 arch/arm/dts/imx8mm-venice-gw700x.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
arch/arm/dts/imx8mm-venice-gw700x.dtsi +1 -2
index f4eb827bae..855c7e02dd 100644
@@ -111,8 +111,7 @@
 			reg = <0>;
 			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
 			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
-			tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
-			rx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
 		};
 	};
 };
Signature · 1 line
2.17.1
author
#3 lore raw

PATCH 4/9 arm: dts: imx8mm-venice-gw7901: use common u-boot dtsi

In reply to Tim Harvey

Use the common imx8mm-u-boot.dtsi

---
 arch/arm/dts/imx8mm-venice-gw7901-u-boot.dtsi | 35 +------------------
 1 file changed, 1 insertion(+), 34 deletions(-)
arch/arm/dts/imx8mm-venice-gw7901-u-boot.dtsi +1 -34
index 6992d91798..a5adf27649 100644
@@ -3,40 +3,7 @@
  * Copyright 2020 Gateworks Corporation
  */
 
-&{/soc@0} {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
-&clk {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-	/delete-property/ assigned-clocks;
-	/delete-property/ assigned-clock-parents;
-	/delete-property/ assigned-clock-rates;
-};
-
-&osc_24m {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips1 {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips2 {
-	u-boot,dm-spl;
-};
-
-&aips3 {
-	u-boot,dm-spl;
-};
-
-&iomuxc {
-	u-boot,dm-spl;
-};
+#include "imx8mm-u-boot.dtsi"
 
 &gpio1 {
 	u-boot,dm-spl;
Signature · 1 line
2.17.1
author
#4 lore raw

PATCH 5/9 board: gateworks: venice: get mem size from dt

In reply to Tim Harvey

Get mem size from dt which SPL updated per EEPROM config.

---
 board/gateworks/venice/imx8mm_venice.c | 28 +++++++++++++-------------
 1 file changed, 14 insertions(+), 14 deletions(-)
board/gateworks/venice/imx8mm_venice.c +14 -14
index 2657bd675f..ff64d697a7 100644
@@ -13,6 +13,7 @@
 #include <asm/arch/clock.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/io.h>
+#include <asm/unaligned.h>
 
 #include "gsc.h"
 
@@ -20,20 +21,19 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int board_phys_sdram_size(phys_size_t *size)
 {
-	int ddr_size = readl(M4_BOOTROM_BASE_ADDR);
-
-	if (ddr_size == 0x4) {
-		*size = 0x100000000;
-	} else if (ddr_size == 0x3) {
-		*size = 0xc0000000;
-	} else if (ddr_size == 0x2) {
-		*size = 0x80000000;
-	} else if (ddr_size == 0x1) {
-		*size = 0x40000000;
-	} else {
-		printf("Unknown DDR type!!!\n");
-		*size = 0x40000000;
-	}
+	const fdt64_t *val;
+	int offset;
+	int len;
+
+	/* get size from dt which SPL updated per EEPROM config */
+	offset = fdt_path_offset(gd->fdt_blob, "/memory");
+	if (offset < 0)
+		return -EINVAL;
+
+	val = fdt_getprop(gd->fdt_blob, offset, "reg", &len);
+	if (len < sizeof(*val) * 2)
+		return -EINVAL;
+	*size = get_unaligned_be64(&val[1]);
 
 	return 0;
 }
Signature · 1 line
2.17.1
author
#5 lore raw

PATCH 6/9 board: gateworks: venice: use bus numbers vs names

In reply to Tim Harvey

replace looking up i2c bus name by bus number and define bus numbers and eeprom address with #defines.

---
 board/gateworks/venice/gsc.c | 19 ++++++++++---------
 board/gateworks/venice/gsc.h |  5 +++++
 board/gateworks/venice/spl.c |  4 ++--
 3 files changed, 17 insertions(+), 11 deletions(-)
board/gateworks/venice/gsc.c +10 -9
index c75bc6f855..c1278e636d 100644
@@ -123,13 +123,13 @@ enum {
 	GSC_SC_RST_CAUSE_MAX		= 10,
 };
 
+#include <dm/device.h>
 static struct udevice *gsc_get_dev(int busno, int slave)
 {
-	static const char * const i2c[] = { "i2c@30a20000", "i2c@30a30000" };
 	struct udevice *dev, *bus;
 	int ret;
 
-	ret = uclass_get_device_by_name(UCLASS_I2C, i2c[busno - 1], &bus);
+	ret = uclass_get_device_by_seq(UCLASS_I2C, busno, &bus);
 	if (ret) {
 		printf("GSC     : failed I2C%d probe: %d\n", busno, ret);
 		return NULL;
@@ -246,7 +246,7 @@ int gsc_hwmon(void)
 		return node;
 
 	/* probe device */
-	dev = gsc_get_dev(1, GSC_HWMON_ADDR);
+	dev = gsc_get_dev(GSC_BUSNO, GSC_HWMON_ADDR);
 	if (!dev) {
 		puts("ERROR: Failed to probe GSC HWMON\n");
 		return -ENODEV;
@@ -453,14 +453,15 @@ static int gsc_read(void)
 {
 	int ret;
 
-	ret = gsc_read_eeprom(1, GSC_EEPROM_ADDR, 1, &som_info);
+	ret = gsc_read_eeprom(GSC_BUSNO, GSC_EEPROM_ADDR, 1, &som_info);
 	if (ret) {
 		memset(&som_info, 0, sizeof(som_info));
 		return ret;
 	}
 
 	/* read optional baseboard EEPROM */
-	return gsc_read_eeprom(2, 0x52, 2, &base_info);
+	return gsc_read_eeprom(BASEBOARD_EEPROM_BUSNO, BASEBOARD_EEPROM_ADDR,
+			       2, &base_info);
 }
 
 static int gsc_info(int verbose)
@@ -518,7 +519,7 @@ static int gsc_info(int verbose)
 
 	/* Display RTC */
 	puts("RTC     : ");
-	dev = gsc_get_dev(1, GSC_RTC_ADDR);
+	dev = gsc_get_dev(GSC_BUSNO, GSC_RTC_ADDR);
 	if (!dev) {
 		puts("Failed to probe GSC RTC\n");
 	} else {
@@ -542,7 +543,7 @@ int gsc_init(int quiet)
 	 */
 	while (1) {
 		/* probe device */
-		dev = gsc_get_dev(1, GSC_SC_ADDR);
+		dev = gsc_get_dev(GSC_BUSNO, GSC_SC_ADDR);
 		if (dev)
 			break;
 		mdelay(1);
@@ -583,7 +584,7 @@ static int gsc_sleep(unsigned long secs)
 	int ret;
 
 	/* probe device */
-	dev = gsc_get_dev(1, GSC_SC_ADDR);
+	dev = gsc_get_dev(GSC_BUSNO, GSC_SC_ADDR);
 	if (!dev)
 		return -ENODEV;
 
@@ -631,7 +632,7 @@ static int gsc_boot_wd_disable(void)
 	int ret;
 
 	/* probe device */
-	dev = gsc_get_dev(1, GSC_SC_ADDR);
+	dev = gsc_get_dev(GSC_BUSNO, GSC_SC_ADDR);
 	if (!dev)
 		return -ENODEV;
 
board/gateworks/venice/gsc.h +5 -0
index 27b02117bb..e0d0332a82 100644
@@ -6,11 +6,16 @@
 #ifndef _GSC_H_
 #define _GSC_H_
 
+/* I2C bus numbers */
+#define GSC_BUSNO			0
+#define BASEBOARD_EEPROM_BUSNO		1
+
 /* I2C slave addresses */
 #define GSC_SC_ADDR             0x20
 #define GSC_RTC_ADDR            0x68
 #define GSC_HWMON_ADDR          0x29
 #define GSC_EEPROM_ADDR         0x51
+#define BASEBOARD_EEPROM_ADDR	0x52
 
 struct venice_board_info {
 	u8 mac[6];		/* 0x00: MAC base */
board/gateworks/venice/spl.c +2 -2
index 8c357757c1..aada55ee27 100644
@@ -116,7 +116,7 @@ static int power_init_board(void)
 	if ((!strncmp(model, "GW71", 4)) ||
 	    (!strncmp(model, "GW72", 4)) ||
 	    (!strncmp(model, "GW73", 4))) {
-		ret = uclass_get_device_by_name(UCLASS_I2C, "i2c@30a20000", &bus);
+		ret = uclass_get_device_by_seq(UCLASS_I2C, 0, &bus);
 		if (ret) {
 			printf("PMIC    : failed I2C1 probe: %d\n", ret);
 			return ret;
@@ -134,7 +134,7 @@ static int power_init_board(void)
 	}
 
 	else if (!strncmp(model, "GW7901", 6)) {
-		ret = uclass_get_device_by_name(UCLASS_I2C, "i2c@30a30000", &bus);
+		ret = uclass_get_device_by_seq(UCLASS_I2C, 1, &bus);
 		if (ret) {
 			printf("PMIC    : failed I2C2 probe: %d\n", ret);
 			return ret;
Signature · 1 line
2.17.1
author
#6 lore raw

PATCH 7/9 board: gateworks: venice: add board model/serial# to env

In reply to Tim Harvey

Add board model/serial# strings to env. Move the creation of the strings to gsc_read() and the display of the info into gsc_info() so they are available to U-Boot proper.

---
 board/gateworks/venice/gsc.c           | 67 ++++++++++++++------------
 board/gateworks/venice/gsc.h           |  1 +
 board/gateworks/venice/imx8mm_venice.c |  4 ++
 3 files changed, 41 insertions(+), 31 deletions(-)
board/gateworks/venice/gsc.c +36 -31
index c1278e636d..b81079eb91 100644
@@ -18,6 +18,7 @@ DECLARE_GLOBAL_DATA_PTR;
 struct venice_board_info som_info;
 struct venice_board_info base_info;
 char venice_model[32];
+uint32_t venice_serial;
 
 /* return a mac address from EEPROM info */
 int gsc_getmac(int index, uint8_t *address)
@@ -451,6 +452,8 @@ const char *gsc_get_dtb_name(int level, char *buf, int sz)
 
 static int gsc_read(void)
 {
+	char rev_pcb;
+	int rev_bom;
 	int ret;
 
 	ret = gsc_read_eeprom(GSC_BUSNO, GSC_EEPROM_ADDR, 1, &som_info);
@@ -460,25 +463,11 @@ static int gsc_read(void)
 	}
 
 	/* read optional baseboard EEPROM */
-	return gsc_read_eeprom(BASEBOARD_EEPROM_BUSNO, BASEBOARD_EEPROM_ADDR,
-			       2, &base_info);
-}
+	gsc_read_eeprom(BASEBOARD_EEPROM_BUSNO, BASEBOARD_EEPROM_ADDR,
+			2, &base_info);
 
-static int gsc_info(int verbose)
-{
-	struct udevice *dev;
-	unsigned char buf[16];
-	char rev_pcb;
-	int rev_bom;
-
-	if (!base_info.model[0]) {
-		strcpy(venice_model, som_info.model);
-		printf("Model   : %s\n", som_info.model);
-		printf("Serial  : %d\n", som_info.serial);
-		printf("MFGDate : %02x-%02x-%02x%02x\n",
-		       som_info.mfgdate[0], som_info.mfgdate[1],
-		       som_info.mfgdate[2], som_info.mfgdate[3]);
-	} else {
+	/* create model strings */
+	if (base_info.model[0]) {
 		sprintf(venice_model, "GW%c%c%c%c-%c%c-",
 			som_info.model[2], /* family */
 			base_info.model[3], /* baseboard */
@@ -499,22 +488,33 @@ static int gsc_info(int verbose)
 			sprintf(venice_model + strlen(venice_model), "%c%d", rev_pcb, rev_bom);
 		else
 			sprintf(venice_model + strlen(venice_model), "%c", rev_pcb);
+	} else {
+		strcpy(venice_model, som_info.model);
+	}
+	venice_serial = som_info.serial;
 
-		if (verbose > 1) {
-			printf("SOM     : %s %d %02x-%02x-%02x%02x\n",
-			       som_info.model, som_info.serial,
-			       som_info.mfgdate[0], som_info.mfgdate[1],
-			       som_info.mfgdate[2], som_info.mfgdate[3]);
-			printf("BASE    : %s %d %02x-%02x-%02x%02x\n",
-			       base_info.model, base_info.serial,
-			       base_info.mfgdate[0], base_info.mfgdate[1],
-			       base_info.mfgdate[2], base_info.mfgdate[3]);
-		}
-		printf("Model   : %s\n", venice_model);
-		printf("Serial  : %d\n", som_info.serial);
-		printf("MFGDate : %02x-%02x-%02x%02x\n",
+	return 0;
+}
+
+static int gsc_info(int verbose)
+{
+	struct udevice *dev;
+	unsigned char buf[16];
+
+	printf("Model   : %s\n", venice_model);
+	printf("Serial  : %d\n", som_info.serial);
+	printf("MFGDate : %02x-%02x-%02x%02x\n",
+	       som_info.mfgdate[0], som_info.mfgdate[1],
+	       som_info.mfgdate[2], som_info.mfgdate[3]);
+	if (base_info.model[0] && verbose > 1) {
+		printf("SOM     : %s %d %02x-%02x-%02x%02x\n",
+		       som_info.model, som_info.serial,
 		       som_info.mfgdate[0], som_info.mfgdate[1],
 		       som_info.mfgdate[2], som_info.mfgdate[3]);
+		printf("BASE    : %s %d %02x-%02x-%02x%02x\n",
+		       base_info.model, base_info.serial,
+		       base_info.mfgdate[0], base_info.mfgdate[1],
+		       base_info.mfgdate[2], base_info.mfgdate[3]);
 	}
 
 	/* Display RTC */
@@ -576,6 +576,11 @@ const char *gsc_get_model(void)
 	return venice_model;
 }
 
+uint32_t gsc_get_serial(void)
+{
+	return venice_serial;
+}
+
 #if !(IS_ENABLED(CONFIG_SPL_BUILD))
 static int gsc_sleep(unsigned long secs)
 {
board/gateworks/venice/gsc.h +1 -0
index e0d0332a82..b391b2e326 100644
@@ -40,5 +40,6 @@ int gsc_hwmon(void);
 const char *gsc_get_model(void);
 const char *gsc_get_dtb_name(int level, char *buf, int len);
 int gsc_getmac(int index, uint8_t *enetaddr);
+uint32_t gsc_get_serial(void);
 
 #endif
board/gateworks/venice/imx8mm_venice.c +4 -0
index ff64d697a7..ca01e75d0d 100644
@@ -113,6 +113,10 @@ int board_late_init(void)
 
 	led_default_state();
 
+	/* Set board serial/model */
+	env_set_ulong("serial#", gsc_get_serial());
+	env_set("model", gsc_get_model());
+
 	/* Set fdt_file vars */
 	i = 0;
 	do {
Signature · 1 line
2.17.1
author
#7 lore raw

PATCH 8/9 board: gateworks: venice: add board model to dt

In reply to Tim Harvey

Add the specific board model from EEPROM config to the device-tree to make it easier to access from Linux userspace.

---
 board/gateworks/venice/imx8mm_venice.c | 8 ++++++++
 configs/imx8mm_venice_defconfig        | 1 +
 2 files changed, 9 insertions(+)
board/gateworks/venice/imx8mm_venice.c +8 -0
index ca01e75d0d..2a97d55d32 100644
@@ -152,3 +152,11 @@ int board_mmc_get_env_dev(int devno)
 {
 	return devno;
 }
+
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+	/* set board model dt prop */
+	fdt_setprop_string(blob, 0, "board", gsc_get_model());
+
+	return 0;
+}
configs/imx8mm_venice_defconfig +1 -0
index f1efdc60a4..58b00a6813 100644
@@ -27,6 +27,7 @@ CONFIG_FIT=y
 CONFIG_FIT_EXTERNAL_OFFSET=0x3000
 CONFIG_SPL_LOAD_FIT=y
 CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_SYSTEM_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/imx8m/imximage-8mm-lpddr4.cfg"
 # CONFIG_USE_BOOTCOMMAND is not set
Signature · 1 line
2.17.1
author
#8 lore raw

PATCH 9/9 board: gateworks: venice: add imx8mm-gw7902 support

In reply to Tim Harvey

The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC

Do the following to add support for it:
- add dts
- add PMIC config

---
 arch/arm/dts/Makefile                         |   1 +
 arch/arm/dts/imx8mm-venice-gw7902-u-boot.dtsi |  80 ++
 arch/arm/dts/imx8mm-venice-gw7902.dts         | 927 ++++++++++++++++++
 board/gateworks/venice/lpddr4_timing.c        | 516 ++++++++++
 board/gateworks/venice/lpddr4_timing.h        |   1 +
 board/gateworks/venice/spl.c                  |  11 +-
 configs/imx8mm_venice_defconfig               |   2 +-
 7 files changed, 1535 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm/dts/imx8mm-venice-gw7902-u-boot.dtsi
 create mode 100644 arch/arm/dts/imx8mm-venice-gw7902.dts
arch/arm/dts/Makefile +1 -0
index 3941a08cf4..a37cd3ee56 100644
@@ -869,6 +869,7 @@ dtb-$(CONFIG_ARCH_IMX8M) += \
 	imx8mm-venice-gw72xx-0x.dtb \
 	imx8mm-venice-gw73xx-0x.dtb \
 	imx8mm-venice-gw7901.dtb \
+	imx8mm-venice-gw7902.dtb \
 	imx8mm-verdin.dtb \
 	phycore-imx8mm.dtb \
 	imx8mn-ddr4-evk.dtb \
arch/arm/dts/imx8mm-venice-gw7902-u-boot.dtsi new file +80 -0

80 lines not on this page · raw message

arch/arm/dts/imx8mm-venice-gw7902.dts new file +927 -0

927 lines not on this page · raw message

board/gateworks/venice/lpddr4_timing.c +516 -0

519 lines not on this page · raw message

board/gateworks/venice/lpddr4_timing.h +1 -0
index 94445f86a4..b73d067f7d 100644
@@ -7,6 +7,7 @@
 #define __LPDDR4_TIMING_H__
 
 extern struct dram_timing_info dram_timing_1gb;
+extern struct dram_timing_info dram_timing_2gb;
 extern struct dram_timing_info dram_timing_4gb;
 
 #endif /* __LPDDR4_TIMING_H__ */
board/gateworks/venice/spl.c +9 -2
index aada55ee27..b819c6846d 100644
@@ -44,6 +44,9 @@ static void spl_dram_init(int size)
 	case 1:
 		dram_timing = &dram_timing_1gb;
 		break;
+	case 2:
+		dram_timing = &dram_timing_2gb;
+		break;
 	case 4:
 		dram_timing = &dram_timing_4gb;
 		break;
@@ -133,8 +136,12 @@ static int power_init_board(void)
 				 BIT(7) | MP5416_VSET_SW3_SVAL(920000));
 	}
 
-	else if (!strncmp(model, "GW7901", 6)) {
-		ret = uclass_get_device_by_seq(UCLASS_I2C, 1, &bus);
+	else if ((!strncmp(model, "GW7901", 6)) ||
+		 (!strncmp(model, "GW7902", 6))) {
+		if (!strncmp(model, "GW7901", 6))
+			ret = uclass_get_device_by_seq(UCLASS_I2C, 1, &bus);
+		else
+			ret = uclass_get_device_by_seq(UCLASS_I2C, 0, &bus);
 		if (ret) {
 			printf("PMIC    : failed I2C2 probe: %d\n", ret);
 			return ret;
configs/imx8mm_venice_defconfig +1 -1
index 58b00a6813..6a8b509127 100644
@@ -57,7 +57,7 @@ CONFIG_CMD_EXT4_WRITE=y
 # CONFIG_SPL_EFI_PARTITION is not set
 CONFIG_OF_CONTROL=y
 CONFIG_SPL_OF_CONTROL=y
-CONFIG_OF_LIST="imx8mm-venice-gw71xx-0x imx8mm-venice-gw72xx-0x imx8mm-venice-gw73xx-0x imx8mm-venice-gw7901"
+CONFIG_OF_LIST="imx8mm-venice-gw71xx-0x imx8mm-venice-gw72xx-0x imx8mm-venice-gw73xx-0x imx8mm-venice-gw7901 imx8mm-venice-gw7902"
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
Signature · 1 line
2.17.1