mlx5 fixes 2021-07-27
From: Saeed Mahameed <[email protected]>
Hi Dave, Jakub,
This series introduces some fixes to mlx5 driver. Please pull and let me know if there is any problem.
Thanks,
Saeed.
---
The following changes since commit 8373cd38a8888549ace7c7617163a2e826970a92:
net: hns3: change the method of obtaining default ptp cycle (2021-07-27 20:59:32 +0100)
are available in the Git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux.git tags/mlx5-fixes-2021-07-27
for you to fetch changes up to 740452e09cf5fc489ce60831cf11abef117b5d26:
net/mlx5: Fix mlx5_vport_tbl_attr chain from u16 to u32 (2021-07-27 16:10:06 -0700)
----------------------------------------------------------------
mlx5-fixes-2021-07-27
----------------------------------------------------------------
Aya Levin (4):
net/mlx5e: Consider PTP-RQ when setting RX VLAN stripping net/mlx5e: Fix page allocation failure for trap-RQ over SF net/mlx5e: Fix page allocation failure for ptp-RQ over SF net/mlx5: Unload device upon firmware fatal error
Chris Mi (1):
net/mlx5: Fix mlx5_vport_tbl_attr chain from u16 to u32
Dima Chumak (1):
net/mlx5e: Fix nullptr in mlx5e_hairpin_get_mdev()
Maor Dickman (2):
net/mlx5e: Disable Rx ntuple offload for uplink representor
net/mlx5: E-Switch, Set destination vport vhca id only when merged eswitch is supported
Maor Gottlieb (1):
net/mlx5: Fix flow table chaining
Maxim Mikityanskiy (1):
net/mlx5e: Add NETIF_F_HW_TC to hw_features when HTB offload is available
Roi Dayan (1):
net/mlx5: E-Switch, handle devcom events only for ports on the same device
Tariq Toukan (1):
net/mlx5e: RX, Avoid possible data corruption when relaxed ordering and LRO combined
drivers/net/ethernet/mellanox/mlx5/core/dev.c | 5 +-- .../net/ethernet/mellanox/mlx5/core/en/params.c | 11 ++++++- drivers/net/ethernet/mellanox/mlx5/core/en/ptp.c | 7 ++-- drivers/net/ethernet/mellanox/mlx5/core/en/trap.c | 2 +- drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 38 +++++++++++++++------- drivers/net/ethernet/mellanox/mlx5/core/en_tc.c | 33 +++++++++++++++++-- drivers/net/ethernet/mellanox/mlx5/core/eswitch.h | 2 +- .../ethernet/mellanox/mlx5/core/eswitch_offloads.c | 10 ++++-- drivers/net/ethernet/mellanox/mlx5/core/fs_core.c | 10 +++--- drivers/net/ethernet/mellanox/mlx5/core/health.c | 12 +++++-- 10 files changed, 98 insertions(+), 32 deletions(-)
PATCH 1/12 net/mlx5: Fix flow table chaining
From: Maor Gottlieb <[email protected]>
Fix a bug when flow table is created in priority that already has other flow tables as shown in the below diagram.
If the new flow table (FT-B) has the lowest level in the priority, we need to connect the flow tables from the previous priority (p0) to this new table. In addition when this flow table is destroyed (FT-B), we need to connect the flow tables from the previous priority (p0) to the next level flow table (FT-C) in the same priority of the destroyed table (if exists).
---------
|root_ns|
---------
|
--------------------------------
| | |
---------- ---------- ---------
|p(prio)-x| | p-y | | p-n |
---------- ---------- ---------
| |
---------------- ------------------
|ns(e.g bypass)| |ns(e.g. kernel) |
---------------- ------------------
| | |
------- ------ ----
| p0 | | p1 | |p2|
------- ------ ----
| | \
-------- ------- ------
| FT-A | |FT-B | |FT-C|
-------- ------- --------- drivers/net/ethernet/mellanox/mlx5/core/fs_core.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/fs_core.c +6 -4
@@ -1024,17 +1024,19 @@ static int connect_fwd_rules(struct mlx5_core_dev *dev,static int connect_flow_table (struct mlx5_core_dev *dev,struct mlx5_flow_table *ft,struct fs_prio *prio) { -struct mlx5_flow_table *next_ft; +struct mlx5_flow_table *next_ft, *first_ft;int err =0 ;/* Connect_prev_fts and update_root_ft_create are mutually exclusive */ -if (list_empty (&prio->node.children)) { + first_ft =list_first_entry_or_null (&prio->node.children, + struct mlx5_flow_table, node.list); +if (!first_ft || first_ft->level > ft->level) { err =connect_prev_fts (dev, ft, prio);if (err)return err; - next_ft =find_next_chained_ft (prio); + next_ft = first_ft ? first_ft :find_next_chained_ft (prio); err =connect_fwd_rules (dev, ft, next_ft);if (err)return err;
@@ -2120,7 +2122,7 @@ static int disconnect_flow_table(struct mlx5_flow_table *ft) node.list) == ft))return 0 ; - next_ft =find_next_chained_ft (prio); + next_ft =find_next_ft (ft); err =connect_fwd_rules (dev, next_ft, ft);if (err)return err;
Signature · 1 line
2.31.1
Re: [net 01/12] net/mlx5: Fix flow table chaining
This series was applied to netdev/net.git (refs/heads/master):
Hello:
This series was applied to netdev/net.git (refs/heads/master):
Quoted 11 lines · On Tue, 27 Jul 2021 16:20:39 -0700 you wrote:
From: Maor Gottlieb <[email protected]>
Fix a bug when flow table is created in priority that already has other flow tables as shown in the below diagram.
If the new flow table (FT-B) has the lowest level in the priority, we need to connect the flow tables from the previous priority (p0) to this new table. In addition when this flow table is destroyed (FT-B), we need to connect the flow tables from the previous priority (p0) to the next level flow table (FT-C) in the same priority of the destroyed table (if exists).
Quoted 1 line
[...]
Here is the summary with links:
- [net,01/12] net/mlx5: Fix flow table chaining
https://git.kernel.org/netdev/net/c/8b54874ef161 - [net,02/12] net/mlx5e: Disable Rx ntuple offload for uplink representor https://git.kernel.org/netdev/net/c/90b22b9bcd24 - [net,03/12] net/mlx5: E-Switch, Set destination vport vhca id only when merged eswitch is supported https://git.kernel.org/netdev/net/c/c671972534c6 - [net,04/12] net/mlx5: E-Switch, handle devcom events only for ports on the same device https://git.kernel.org/netdev/net/c/dd3fddb82780 - [net,05/12] net/mlx5e: RX, Avoid possible data corruption when relaxed ordering and LRO combined https://git.kernel.org/netdev/net/c/e2351e517068 - [net,06/12] net/mlx5e: Add NETIF_F_HW_TC to hw_features when HTB offload is available https://git.kernel.org/netdev/net/c/9841d58f3550 - [net,07/12] net/mlx5e: Consider PTP-RQ when setting RX VLAN stripping https://git.kernel.org/netdev/net/c/a759f845d1f7 - [net,08/12] net/mlx5e: Fix page allocation failure for trap-RQ over SF https://git.kernel.org/netdev/net/c/497008e78345 - [net,09/12] net/mlx5e: Fix page allocation failure for ptp-RQ over SF https://git.kernel.org/netdev/net/c/678b1ae1af4a - [net,10/12] net/mlx5: Unload device upon firmware fatal error https://git.kernel.org/netdev/net/c/7f331bf0f060 - [net,11/12] net/mlx5e: Fix nullptr in mlx5e_hairpin_get_mdev() https://git.kernel.org/netdev/net/c/b1c2f6312c50 - [net,12/12] net/mlx5: Fix mlx5_vport_tbl_attr chain from u16 to u32 https://git.kernel.org/netdev/net/c/740452e09cf5
You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html
PATCH 2/12 net/mlx5e: Disable Rx ntuple offload for uplink representor
In reply to Saeed MahameedFrom: Maor Dickman <[email protected]>
Rx ntuple offload is not supported in switchdev mode. Tryng to enable it cause kernel panic.
BUG: kernel NULL pointer dereference, address: 0000000000000008 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 80000001065a5067 P4D 80000001065a5067 PUD 106594067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 7 PID: 1089 Comm: ethtool Not tainted 5.13.0-rc7_for_upstream_min_debug_2021_06_23_16_44 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5e_arfs_enable+0x70/0xd0 [mlx5_core] Code: 44 24 10 00 00 00 00 48 c7 44 24 18 00 00 00 00 49 63 c4 48 89 e2 44 89 e6 48 69 c0 20 08 00 00 48 89 ef 48 03 85 68 ac 00 00 <48> 8b 40 08 48 89 44 24 08 e8 d2 aa fd ff 48 83 05 82 96 18 00 01 RSP: 0018:ffff8881047679e0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000004000000000 RCX: 0000004000000000 RDX: ffff8881047679e0 RSI: 0000000000000000 RDI: ffff888115100880 RBP: ffff888115100880 R08: ffffffffa00f6cb0 R09: ffff888104767a18 R10: ffff8881151000a0 R11: ffff888109479540 R12: 0000000000000000 R13: ffff888104767bb8 R14: ffff888115100000 R15: ffff8881151000a0 FS: 00007f41a64ab740(0000) GS:ffff8882f5dc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 0000000104cbc005 CR4: 0000000000370ea0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: set_feature_arfs+0x1e/0x40 [mlx5_core] mlx5e_handle_feature+0x43/0xa0 [mlx5_core] mlx5e_set_features+0x139/0x1b0 [mlx5_core] __netdev_update_features+0x2b3/0xaf0 ethnl_set_features+0x176/0x3a0 ? __nla_parse+0x22/0x30 genl_family_rcv_msg_doit+0xe2/0x140 genl_rcv_msg+0xde/0x1d0 ? features_reply_size+0xe0/0xe0 ? genl_get_cmd+0xd0/0xd0 netlink_rcv_skb+0x4e/0xf0 genl_rcv+0x24/0x40 netlink_unicast+0x1f6/0x2b0 netlink_sendmsg+0x225/0x450 sock_sendmsg+0x33/0x40 __sys_sendto+0xd4/0x120 ? __sys_recvmsg+0x4e/0x90 ? exc_page_fault+0x219/0x740 __x64_sys_sendto+0x25/0x30 do_syscall_64+0x3f/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f41a65b0cba Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 76 c3 0f 1f 44 00 00 55 48 83 ec 30 44 89 4c RSP: 002b:00007ffd8d688358 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00000000010f42a0 RCX: 00007f41a65b0cba RDX: 0000000000000058 RSI: 00000000010f43b0 RDI: 0000000000000003 RBP: 000000000047ae60 R08: 00007f41a667c000 R09: 000000000000000c R10: 0000000000000000 R11: 0000000000000246 R12: 00000000010f4340 R13: 00000000010f4350 R14: 00007ffd8d688400 R15: 00000000010f42a0 Modules linked in: mlx5_vdpa vhost_iotlb vdpa xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad ib_ipoib rdma_cm iw_cm ib_cm mlx5_ib ib_uverbs ib_core overlay mlx5_core ptp pps_core fuse CR2: 0000000000000008 ---[ end trace c66523f2aba94b43 ]---
--- .../net/ethernet/mellanox/mlx5/core/en_main.c | 29 +++++++++++++------ 1 file changed, 20 insertions(+), 9 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/en_main.c +20 -9
@@ -3829,6 +3829,24 @@ int mlx5e_set_features(struct net_device *netdev, netdev_features_t features)return 0 ; } +static netdev_features_t mlx5e_fix_uplink_rep_features (struct net_device *netdev, +netdev_features_t features) +{ + features &= ~NETIF_F_HW_TLS_RX ; +if (netdev->features &NETIF_F_HW_TLS_RX ) +netdev_warn (netdev,"Disabling hw_tls_rx, not supported in switchdev mode\n" ); + + features &= ~NETIF_F_HW_TLS_TX ; +if (netdev->features &NETIF_F_HW_TLS_TX ) +netdev_warn (netdev,"Disabling hw_tls_tx, not supported in switchdev mode\n" ); + + features &= ~NETIF_F_NTUPLE ; +if (netdev->features &NETIF_F_NTUPLE ) +netdev_warn (netdev,"Disabling ntuple, not supported in switchdev mode\n" ); + +return features; +} +static netdev_features_t mlx5e_fix_features (struct net_device *netdev,netdev_features_t features) {
@@ -3860,15 +3878,8 @@ static netdev_features_t mlx5e_fix_features(struct net_device *netdev,netdev_warn (netdev,"Disabling rxhash, not supported when CQE compress is active\n" ); } -if (mlx5e_is_uplink_rep (priv)) { - features &= ~NETIF_F_HW_TLS_RX ; -if (netdev->features &NETIF_F_HW_TLS_RX ) -netdev_warn (netdev,"Disabling hw_tls_rx, not supported in switchdev mode\n" ); - - features &= ~NETIF_F_HW_TLS_TX ; -if (netdev->features &NETIF_F_HW_TLS_TX ) -netdev_warn (netdev,"Disabling hw_tls_tx, not supported in switchdev mode\n" ); - } +if (mlx5e_is_uplink_rep (priv)) + features =mlx5e_fix_uplink_rep_features (netdev, features);mutex_unlock (&priv->state_lock);
Signature · 1 line
2.31.1
PATCH 3/12 net/mlx5: E-Switch, Set destination vport vhca id only when merged eswitch is supported
In reply to Saeed MahameedFrom: Maor Dickman <[email protected]>
Destination vport vhca id is valid flag is set only merged eswitch isn't supported. Change destination vport vhca id value to be set also only when merged eswitch is supported.
--- drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c +4 -3
@@ -382,10 +382,11 @@ esw_setup_vport_dest(struct mlx5_flow_destination *dest, struct mlx5_flow_act *f { dest[dest_idx].type =MLX5_FLOW_DESTINATION_TYPE_VPORT ; dest[dest_idx].vport.num = esw_attr->dests[attr_idx].rep->vport; - dest[dest_idx].vport.vhca_id = -MLX5_CAP_GEN (esw_attr->dests[attr_idx].mdev, vhca_id); -if (MLX5_CAP_ESW (esw->dev, merged_eswitch)) +if (MLX5_CAP_ESW (esw->dev, merged_eswitch)) { + dest[dest_idx].vport.vhca_id = +MLX5_CAP_GEN (esw_attr->dests[attr_idx].mdev, vhca_id); dest[dest_idx].vport.flags |=MLX5_FLOW_DEST_VPORT_VHCA_ID ; + }if (esw_attr->dests[attr_idx].flags &MLX5_ESW_DEST_ENCAP ) {if (pkt_reformat) { flow_act->action |=MLX5_FLOW_CONTEXT_ACTION_PACKET_REFORMAT ;
Signature · 1 line
2.31.1
PATCH 4/12 net/mlx5: E-Switch, handle devcom events only for ports on the same device
In reply to Saeed MahameedFrom: Roi Dayan <[email protected]>
This is the same check as LAG mode checks if to enable lag. This will fix adding peer miss rules if lag is not supported and even an incorrect rules in socket direct mode.
Also fix the incorrect comment on mlx5_get_next_phys_dev() as flow #1 doesn't exists.
--- drivers/net/ethernet/mellanox/mlx5/core/dev.c | 5 +---- drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c | 3 +++ 2 files changed, 4 insertions(+), 4 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/dev.c +1 -4
@@ -500,10 +500,7 @@ static int next_phys_dev(struct device *dev, const void *data)return 1 ; } -/* This function is called with two flows: -* 1. During initialization of mlx5_core_dev and we don't need to lock it. -* 2. During LAG configure stage and caller holds &mlx5_intf_mutex. -*/ +/* Must be called with intf_mutex held */ struct mlx5_core_dev *mlx5_get_next_phys_dev (struct mlx5_core_dev *dev) {struct auxiliary_device *adev;
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c +3 -0
@@ -2368,6 +2368,9 @@ static int mlx5_esw_offloads_devcom_event(int event,switch (event) {case ESW_OFFLOADS_DEVCOM_PAIR : +if (mlx5_get_next_phys_dev (esw->dev) != peer_esw->dev) +break ; +if (mlx5_eswitch_vport_match_metadata_enabled (esw) !=mlx5_eswitch_vport_match_metadata_enabled (peer_esw))break ;
Signature · 1 line
2.31.1
PATCH 5/12 net/mlx5e: RX, Avoid possible data corruption when relaxed ordering and LRO combined
In reply to Saeed MahameedFrom: Tariq Toukan <[email protected]>
When HW aggregates packets for an LRO session, it writes the payload of two consecutive packets of a flow contiguously, so that they usually share a cacheline.
The first byte of a packet's payload is written immediately after the last byte of the preceding packet.
In this flow, there are two consecutive write requests to the shared cacheline:
1. Regular write for the earlier packet.
2. Read-modify-write for the following packet.
In case of relaxed-ordering on, these two writes might be re-ordered. Using the end padding optimization (to avoid partial write for the last cacheline of a packet) becomes problematic if the two writes occur out-of-order, as the padding would overwrite payload that belongs to the following packet, causing data corruption.
Avoid this by disabling the end padding optimization when both LRO and relaxed-ordering are enabled.
--- drivers/net/ethernet/mellanox/mlx5/core/en/params.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)
drivers/net/ethernet/mellanox/mlx5/core/en/params.c +10 -1
@@ -471,6 +471,15 @@ static void mlx5e_build_rx_cq_param(struct mlx5_core_dev *mdev, param->cq_period_mode = params->rx_cq_moderation.cq_period_mode; } +static u8 rq_end_pad_mode (struct mlx5_core_dev *mdev,struct mlx5e_params *params) +{ +bool ro =pcie_relaxed_ordering_enabled (mdev->pdev) && +MLX5_CAP_GEN (mdev, relaxed_ordering_write); + +return ro && params->lro_en ? +MLX5_WQ_END_PAD_MODE_NONE :MLX5_WQ_END_PAD_MODE_ALIGN ; +} + int mlx5e_build_rq_param(struct mlx5_core_dev *mdev, struct mlx5e_params *params, struct mlx5e_xsk_param *xsk,
@@ -508,7 +517,7 @@ int mlx5e_build_rq_param(struct mlx5_core_dev *mdev, }MLX5_SET (wq, wq, wq_type, params->rq_wq_type); -MLX5_SET (wq, wq, end_padding_mode,MLX5_WQ_END_PAD_MODE_ALIGN ); +MLX5_SET (wq, wq, end_padding_mode,rq_end_pad_mode (mdev, params));MLX5_SET (wq, wq, log_wq_stride,mlx5e_get_rqwq_log_stride (params->rq_wq_type, ndsegs));MLX5_SET (wq, wq, pd, mdev->mlx5e_res.hw_objs.pdn);
Signature · 1 line
2.31.1
PATCH 6/12 net/mlx5e: Add NETIF_F_HW_TC to hw_features when HTB offload is available
In reply to Saeed MahameedFrom: Maxim Mikityanskiy <[email protected]>
If a feature flag is only present in features, but not in hw_features, the user can't reset it. Although hw_features may contain NETIF_F_HW_TC by the point where the driver checks whether HTB offload is supported, this flag is controlled by another condition that may not hold. Set it explicitly to make sure the user can disable it.
--- drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/en_main.c +3 -2
@@ -4870,6 +4870,9 @@ static void mlx5e_build_nic_netdev(struct net_device *netdev)if (MLX5_CAP_ETH (mdev, scatter_fcs)) netdev->hw_features |=NETIF_F_RXFCS ; +if (mlx5_qos_is_supported (mdev)) + netdev->hw_features |=NETIF_F_HW_TC ; + netdev->features = netdev->hw_features;/* Defaults */
@@ -4890,8 +4893,6 @@ static void mlx5e_build_nic_netdev(struct net_device *netdev) netdev->hw_features |=NETIF_F_NTUPLE ;#endif } -if (mlx5_qos_is_supported (mdev)) - netdev->features |=NETIF_F_HW_TC ; netdev->features |=NETIF_F_HIGHDMA ; netdev->features |=NETIF_F_HW_VLAN_STAG_FILTER ;
Signature · 1 line
2.31.1
PATCH 7/12 net/mlx5e: Consider PTP-RQ when setting RX VLAN stripping
In reply to Saeed MahameedFrom: Aya Levin <[email protected]>
Add PTP-RQ to the loop when setting rx-vlan-offload feature via ethtool. On PTP-RQ's creation, set rx-vlan-offload into its parameters.
--- drivers/net/ethernet/mellanox/mlx5/core/en/ptp.c | 5 ++++- drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 4 +++- 2 files changed, 7 insertions(+), 2 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/en/ptp.c +4 -1
@@ -482,8 +482,11 @@ static void mlx5e_ptp_build_params(struct mlx5e_ptp *c, params->log_sq_size = orig->log_sq_size;mlx5e_ptp_build_sq_param (c->mdev, params, &cparams->txq_sq_param); } -if (test_bit (MLX5E_PTP_STATE_RX , c->state)) +/* RQ */ +if (test_bit (MLX5E_PTP_STATE_RX , c->state)) { + params->vlan_strip_disable = orig->vlan_strip_disable;mlx5e_ptp_build_rq_param (c->mdev, c->netdev, c->priv->q_counter, cparams); + } } static int mlx5e_init_ptp_rq(struct mlx5e_ptp *c, struct mlx5e_params *params,
drivers/net/ethernet/mellanox/mlx5/core/en_main.c +3 -1
@@ -3384,7 +3384,7 @@ static int mlx5e_modify_channels_scatter_fcs(struct mlx5e_channels *chs, bool enstatic int mlx5e_modify_channels_vsd (struct mlx5e_channels *chs,bool vsd) { -int err =0 ; +int err;int i;for (i =0 ; i < chs->num; i++) {
@@ -3392,6 +3392,8 @@ static int mlx5e_modify_channels_vsd(struct mlx5e_channels *chs, bool vsd)if (err)return err; } +if (chs->ptp &&test_bit (MLX5E_PTP_STATE_RX , chs->ptp->state)) +return mlx5e_modify_rq_vsd (&chs->ptp->rq, vsd);return 0 ; }
Signature · 1 line
2.31.1
PATCH 8/12 net/mlx5e: Fix page allocation failure for trap-RQ over SF
In reply to Saeed MahameedFrom: Aya Levin <[email protected]>
Set the correct device pointer to the trap-RQ, to allow access to dma_mask and avoid allocation request with the wrong pci-dev.
WARNING: CPU: 1 PID: 12005 at kernel/dma/mapping.c:151 dma_map_page_attrs+0x139/0x1c0 ... all Trace: <IRQ> ? __page_pool_alloc_pages_slow+0x5a/0x210 mlx5e_post_rx_wqes+0x258/0x400 [mlx5_core] mlx5e_trap_napi_poll+0x44/0xc0 [mlx5_core] __napi_poll+0x24/0x150 net_rx_action+0x22b/0x280 __do_softirq+0xc7/0x27e do_softirq+0x61/0x80 </IRQ> __local_bh_enable_ip+0x4b/0x50 mlx5e_handle_action_trap+0x2dd/0x4d0 [mlx5_core] blocking_notifier_call_chain+0x5a/0x80 mlx5_devlink_trap_action_set+0x8b/0x100 [mlx5_core]
--- drivers/net/ethernet/mellanox/mlx5/core/en/trap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/mellanox/mlx5/core/en/trap.c +1 -1
@@ -37,7 +37,7 @@ static void mlx5e_init_trap_rq(struct mlx5e_trap *t, struct mlx5e_params *paramsstruct mlx5e_priv *priv = t->priv; rq->wq_type = params->rq_wq_type; - rq->pdev = mdev->device; + rq->pdev = t->pdev; rq->netdev = priv->netdev; rq->priv = priv; rq->clock = &mdev->clock;
Signature · 1 line
2.31.1
PATCH 9/12 net/mlx5e: Fix page allocation failure for ptp-RQ over SF
In reply to Saeed MahameedFrom: Aya Levin <[email protected]>
Set the correct pci-device pointer to the ptp-RQ. This allows access to dma_mask and avoids allocation request with wrong pci-device.
--- drivers/net/ethernet/mellanox/mlx5/core/en/ptp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/mellanox/mlx5/core/en/ptp.c +1 -1
@@ -497,7 +497,7 @@ static int mlx5e_init_ptp_rq(struct mlx5e_ptp *c, struct mlx5e_params *params,int err; rq->wq_type = params->rq_wq_type; - rq->pdev = mdev->device; + rq->pdev = c->pdev; rq->netdev = priv->netdev; rq->priv = priv; rq->clock = &mdev->clock;
Signature · 1 line
2.31.1
PATCH 10/12 net/mlx5: Unload device upon firmware fatal error
In reply to Saeed MahameedFrom: Aya Levin <[email protected]>
When fw_fatal reporter reports an error, the firmware in not responding. Unload the device to ensure that the driver closes all its resources, even if recovery is not due (user disabled auto-recovery or reporter is in grace period). On successful recovery the device is loaded back up.
--- drivers/net/ethernet/mellanox/mlx5/core/health.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/health.c +10 -2
@@ -626,8 +626,16 @@ static void mlx5_fw_fatal_reporter_err_work(struct work_struct *work) } fw_reporter_ctx.err_synd = health->synd; fw_reporter_ctx.miss_counter = health->miss_counter; -devlink_health_report (health->fw_fatal_reporter, -"FW fatal error reported" , &fw_reporter_ctx); +if (devlink_health_report (health->fw_fatal_reporter, +"FW fatal error reported" , &fw_reporter_ctx) == -ECANCELED ) { +/* If recovery wasn't performed, due to grace period, +* unload the driver. This ensures that the driver +* closes all its resources and it is not subjected to +* requests from the kernel. +*/ +mlx5_core_err (dev,"Driver is in error state. Unloading\n" ); +mlx5_unload_one (dev); + } }static const struct devlink_health_reporter_ops mlx5_fw_fatal_reporter_ops = {
Signature · 1 line
2.31.1
PATCH 11/12 net/mlx5e: Fix nullptr in mlx5e_hairpin_get_mdev()
In reply to Saeed MahameedFrom: Dima Chumak <[email protected]>
The result of __dev_get_by_index() is not checked for NULL and then gets dereferenced immediately.
Also, __dev_get_by_index() must be called while holding either RTNL lock or @dev_base_lock, which isn't satisfied by mlx5e_hairpin_get_mdev() or its callers. This makes the underlying hlist_for_each_entry() loop not safe, and can have adverse effects in itself.
Fix by using dev_get_by_index() and handling nullptr return value when ifindex device is not found. Update mlx5e_hairpin_get_mdev() callers to check for possible PTR_ERR() result.
Addresses-Coverity: ("Dereference null return value")
--- .../net/ethernet/mellanox/mlx5/core/en_tc.c | 33 +++++++++++++++++-- 1 file changed, 31 insertions(+), 2 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c +31 -2
@@ -452,12 +452,32 @@ static void mlx5e_detach_mod_hdr(struct mlx5e_priv *priv,static struct mlx5_core_dev *mlx5e_hairpin_get_mdev (struct net *net,int ifindex) { +struct mlx5_core_dev *mdev;struct net_device *netdev;struct mlx5e_priv *priv; - netdev =__dev_get_by_index (net, ifindex); + netdev =dev_get_by_index (net, ifindex); +if (!netdev) +return ERR_PTR (-ENODEV ); + priv =netdev_priv (netdev); -return priv->mdev; + mdev = priv->mdev; +dev_put (netdev); + +/* Mirred tc action holds a refcount on the ifindex net_device (see +* net/sched/act_mirred.c:tcf_mirred_get_dev). So, it's okay to continue using mdev +* after dev_put(netdev), while we're in the context of adding a tc flow. +* +* The mdev pointer corresponds to the peer/out net_device of a hairpin. It is then +* stored in a hairpin object, which exists until all flows, that refer to it, get +* removed. +* +* On the other hand, after a hairpin object has been created, the peer net_device may +* be removed/unbound while there are still some hairpin flows that are using it. This +* case is handled by mlx5e_tc_hairpin_update_dead_peer, which is hooked to +* NETDEV_UNREGISTER event of the peer net_device. +*/ +return mdev; }static int mlx5e_hairpin_create_transport (struct mlx5e_hairpin *hp)
@@ -666,6 +686,10 @@ mlx5e_hairpin_create(struct mlx5e_priv *priv, struct mlx5_hairpin_params *params func_mdev = priv->mdev; peer_mdev =mlx5e_hairpin_get_mdev (dev_net (priv->netdev), peer_ifindex); +if (IS_ERR (peer_mdev)) { + err =PTR_ERR (peer_mdev); + goto create_pair_err; + } pair =mlx5_core_hairpin_create (func_mdev, peer_mdev, params);if (IS_ERR (pair)) {
@@ -804,6 +828,11 @@ static int mlx5e_hairpin_flow_add(struct mlx5e_priv *priv,int err; peer_mdev =mlx5e_hairpin_get_mdev (dev_net (priv->netdev), peer_ifindex); +if (IS_ERR (peer_mdev)) { +NL_SET_ERR_MSG_MOD (extack,"invalid ifindex of mirred device" ); +return PTR_ERR (peer_mdev); + } +if (!MLX5_CAP_GEN (priv->mdev, hairpin) || !MLX5_CAP_GEN (peer_mdev, hairpin)) {NL_SET_ERR_MSG_MOD (extack,"hairpin is not supported" );return -EOPNOTSUPP ;
Signature · 1 line
2.31.1
PATCH 12/12 net/mlx5: Fix mlx5_vport_tbl_attr chain from u16 to u32
In reply to Saeed MahameedFrom: Chris Mi <[email protected]>
The offending refactor commit uses u16 chain wrongly. Actually, it should be u32.
--- drivers/net/ethernet/mellanox/mlx5/core/eswitch.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/mellanox/mlx5/core/eswitch.h +1 -1
@@ -636,7 +636,7 @@ struct esw_vport_tbl_namespace { };struct mlx5_vport_tbl_attr { -u16 chain; +u32 chain;u16 prio;u16 vport;const struct esw_vport_tbl_namespace *vport_ns;
Signature · 1 line
2.31.1