Skip to contentSkip to conversation

Tegra ARM32 device-tree improvements for 5.15

PATCH Applied Dmitry Osipenko 2 participants 17 messages Aug 2, 2021 – Aug 11, 2021

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v2 cover Tegra ARM32 device-tree improvements for 5.15

This series:

- adds SoC thermal sensor node
- adds interrupt for LM90 to Ouya, AC100, Nexus 7 and A500 devices
- fixes interrupt of LM90 sensor for all boards
- removes bogus VBUS regulators from A500 device-tree
- improves thermal zones of Nexus 7 and A500 devices based on previous discussion with Daniel Lezcano [1]

[1] https://lore.kernel.org/lkml/[email protected]/

Changelog:

v2: - Added these new minor patches:

ARM: tegra: acer-a500: Add power supplies to accelerometer
ARM: tegra: acer-a500: Use verbose variant of atmel,wakeup-method

Dmitry Osipenko (15):
ARM: tegra: Add SoC thermal sensor to Tegra30 device-trees
ARM: tegra: ouya: Add interrupt to temperature sensor node
ARM: tegra: paz00: Add interrupt to temperature sensor node
ARM: tegra: nexus7: Add interrupt to temperature sensor node
ARM: tegra: acer-a500: Add interrupt to temperature sensor node
ARM: tegra: nyan: Correct interrupt trigger type of temperature sensor
ARM: tegra: apalis: Correct interrupt trigger type of temperature
sensor
ARM: tegra: cardhu: Correct interrupt trigger type of temperature
sensor
ARM: tegra: dalmore: Correct interrupt trigger type of temperature
sensor
ARM: tegra: jetson-tk1: Correct interrupt trigger type of temperature
sensor
ARM: tegra: acer-a500: Remove bogus USB VBUS regulators
ARM: tegra: acer-a500: Add power supplies to accelerometer
ARM: tegra: acer-a500: Use verbose variant of atmel,wakeup-method
value
ARM: tegra: acer-a500: Improve thermal zones
ARM: tegra: nexus7: Improve thermal zones

 arch/arm/boot/dts/tegra114-dalmore.dts        |  2 +-
 arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi   |  2 +-
 arch/arm/boot/dts/tegra124-apalis.dtsi        |  2 +-
 arch/arm/boot/dts/tegra124-jetson-tk1.dts     |  2 +-
 arch/arm/boot/dts/tegra124-nyan.dtsi          |  2 +-
 .../boot/dts/tegra20-acer-a500-picasso.dts    | 90 ++++++++++++-------
 arch/arm/boot/dts/tegra20-paz00.dts           |  4 +
 .../tegra30-asus-nexus7-grouper-common.dtsi   | 60 ++++++++++++-
 arch/arm/boot/dts/tegra30-cardhu.dtsi         |  2 +-
 arch/arm/boot/dts/tegra30-ouya.dts            | 13 ++-
 arch/arm/boot/dts/tegra30.dtsi                | 87 +++++++++++++++++-
 11 files changed, 211 insertions(+), 55 deletions(-)
Signature · 1 line
2.32.0
#1 lore raw

PATCH v2 1/15 ARM: tegra: Add SoC thermal sensor to Tegra30 device-trees

Add the on-chip SoC thermal sensor to Tegra30 device-trees. Now CPU temperature reporting and thermal throttling is available on all Tegra30 devices universally.

---
 arch/arm/boot/dts/tegra30.dtsi | 87 ++++++++++++++++++++++++++++++++--
 1 file changed, 83 insertions(+), 4 deletions(-)
arch/arm/boot/dts/tegra30.dtsi +83 -4
index c577c191be4b..eaf4951d9ff8 100644
@@ -5,6 +5,7 @@
 #include <dt-bindings/pinctrl/pinctrl-tegra.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/soc/tegra-pmc.h>
+#include <dt-bindings/thermal/thermal.h>
 
 #include "tegra30-peripherals-opp.dtsi"
 
@@ -800,6 +801,20 @@ fuse@7000f800 {
 		reset-names = "fuse";
 	};
 
+	tsensor: tsensor@70014000 {
+		compatible = "nvidia,tegra30-tsensor";
+		reg = <0x70014000 0x500>;
+		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA30_CLK_TSENSOR>;
+		resets = <&tegra_car TEGRA30_CLK_TSENSOR>;
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_TSENSOR>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_CLK_M>;
+		assigned-clock-rates = <500000>;
+
+		#thermal-sensor-cells = <1>;
+	};
+
 	hda@70030000 {
 		compatible = "nvidia,tegra30-hda";
 		reg = <0x70030000 0x10000>;
@@ -1062,32 +1077,36 @@ cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <0>;
 			clocks = <&tegra_car TEGRA30_CLK_CCLK_G>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <1>;
 			clocks = <&tegra_car TEGRA30_CLK_CCLK_G>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <2>;
 			clocks = <&tegra_car TEGRA30_CLK_CCLK_G>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <3>;
 			clocks = <&tegra_car TEGRA30_CLK_CCLK_G>;
+			#cooling-cells = <2>;
 		};
 	};
 
@@ -1102,4 +1121,64 @@ pmu {
 				     <&{/cpus/cpu@2}>,
 				     <&{/cpus/cpu@3}>;
 	};
+
+	thermal-zones {
+		tsensor0-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&tsensor 0>;
+
+			trips {
+				level1_trip: dvfs-alert {
+					/* throttle at 80C until temperature drops to 79.8C */
+					temperature = <80000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				level2_trip: cpu-div2-throttle {
+					/* hardware CPU x2 freq throttle at 85C */
+					temperature = <85000>;
+					hysteresis = <200>;
+					type = "hot";
+				};
+
+				level3_trip: soc-critical {
+					/* hardware shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&level1_trip>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		tsensor1-thermal {
+			status = "disabled";
+
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <0>; /* milliseconds */
+
+			thermal-sensors = <&tsensor 1>;
+
+			trips {
+				dvfs-alert {
+					temperature = <80000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+			};
+		};
+	};
 };
Signature · 1 line
2.32.0
#2 lore raw

PATCH v2 2/15 ARM: tegra: ouya: Add interrupt to temperature sensor node

In reply to Dmitry Osipenko

The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC. Add interrupt property to the temperature sensor and enable it in pinmux, for completeness.

---
 arch/arm/boot/dts/tegra30-ouya.dts | 13 ++++++-------
 1 file changed, 6 insertions(+), 7 deletions(-)
arch/arm/boot/dts/tegra30-ouya.dts +6 -7
index ab8744f3d72d..90db5ff72537 100644
@@ -124,12 +124,11 @@ cpu_temp: nct1008@4c {
 			compatible = "onnn,nct1008";
 			reg = <0x4c>;
 			vcc-supply = <&sys_3v3_reg>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
+
 			#thermal-sensor-cells = <1>;
-/*
- *			The interrupt is bugged, once triggered it never clears.
- *			interrupt-parent = <&gpio>;
- *			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_LEVEL_LOW>;
- */
 		};
 
 		pmic: pmic@2d {
@@ -4376,8 +4375,8 @@ pcc2 {
 		nvidia,pins = "pcc2";
 		nvidia,function = "i2s4";
 		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+		nvidia,tristate = <TEGRA_PIN_DISABLE>;
+		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 	};
 	sdmmc4_rst_n_pcc3 {
 		nvidia,pins = "sdmmc4_rst_n_pcc3";
Signature · 1 line
2.32.0
#3 lore raw

PATCH v2 3/15 ARM: tegra: paz00: Add interrupt to temperature sensor node

In reply to Dmitry Osipenko

The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC. Add interrupt property to the temperature sensor for completeness.

---
 arch/arm/boot/dts/tegra20-paz00.dts | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm/boot/dts/tegra20-paz00.dts +4 -0
index 3180bff90756..acc816bfd233 100644
@@ -503,6 +503,10 @@ ldo_rtc {
 		adt7461: temperature-sensor@4c {
 			compatible = "adi,adt7461";
 			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(N, 6) IRQ_TYPE_EDGE_FALLING>;
+
 			#thermal-sensor-cells = <1>;
 		};
 	};
Signature · 1 line
2.32.0
#4 lore raw

PATCH v2 4/15 ARM: tegra: nexus7: Add interrupt to temperature sensor node

In reply to Dmitry Osipenko

The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC. Add interrupt property to the temperature sensor for completeness.

---
 arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi +4 -0
index ae8300baa2d4..33985fca956f 100644
@@ -920,6 +920,10 @@ nct72: temperature-sensor@4c {
 			compatible = "onnn,nct1008";
 			reg = <0x4c>;
 			vcc-supply = <&vdd_3v3_sys>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(S, 3) IRQ_TYPE_EDGE_FALLING>;
+
 			#thermal-sensor-cells = <1>;
 		};
 
Signature · 1 line
2.32.0
#5 lore raw

PATCH v2 5/15 ARM: tegra: acer-a500: Add interrupt to temperature sensor node

In reply to Dmitry Osipenko

The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC. Add interrupt property to the temperature sensor for completeness.

---
 arch/arm/boot/dts/tegra20-acer-a500-picasso.dts | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +4 -0
index 1976c383912a..4897079680bd 100644
@@ -693,6 +693,10 @@ nct1008: temperature-sensor@4c {
 			compatible = "onnn,nct1008";
 			reg = <0x4c>;
 			vcc-supply = <&vdd_3v3_sys>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(N, 6) IRQ_TYPE_EDGE_FALLING>;
+
 			#thermal-sensor-cells = <1>;
 		};
 	};
Signature · 1 line
2.32.0
#6 lore raw

PATCH v2 6/15 ARM: tegra: nyan: Correct interrupt trigger type of temperature sensor

In reply to Dmitry Osipenko

The LM90 temperature sensor should use edge-triggered interrupt because LM90 hardware doesn't deassert interrupt line until temperature is back to normal state, which results in interrupt storm. Correct the interrupt trigger type.

---
 arch/arm/boot/dts/tegra124-nyan.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/tegra124-nyan.dtsi +1 -1
index 5f71add38dfe..63a81270300a 100644
@@ -91,7 +91,7 @@ temperature-sensor@4c {
 			compatible = "ti,tmp451";
 			reg = <0x4c>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_EDGE_FALLING>;
 
 			#thermal-sensor-cells = <1>;
 		};
Signature · 1 line
2.32.0
#7 lore raw

PATCH v2 7/15 ARM: tegra: apalis: Correct interrupt trigger type of temperature sensor

In reply to Dmitry Osipenko

The LM90 temperature sensor should use edge-triggered interrupt because LM90 hardware doesn't deassert interrupt line until temperature is back to normal state, which results in interrupt storm. Correct the interrupt trigger type.

---
 arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi | 2 +-
 arch/arm/boot/dts/tegra124-apalis.dtsi      | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi +1 -1
index 1e30fa405fa0..cde9ae8fa04b 100644
@@ -1751,7 +1751,7 @@ temp-sensor@4c {
 			compatible = "ti,tmp451";
 			reg = <0x4c>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_EDGE_FALLING>;
 			#thermal-sensor-cells = <1>;
 			vcc-supply = <&reg_module_3v3>;
 		};
arch/arm/boot/dts/tegra124-apalis.dtsi +1 -1
index 608896f8dd52..a46d9ba9bb7a 100644
@@ -1744,7 +1744,7 @@ temp-sensor@4c {
 			compatible = "ti,tmp451";
 			reg = <0x4c>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_EDGE_FALLING>;
 			#thermal-sensor-cells = <1>;
 			vcc-supply = <&reg_module_3v3>;
 		};
Signature · 1 line
2.32.0
#8 lore raw

PATCH v2 8/15 ARM: tegra: cardhu: Correct interrupt trigger type of temperature sensor

In reply to Dmitry Osipenko

The LM90 temperature sensor should use edge-triggered interrupt because LM90 hardware doesn't deassert interrupt line until temperature is back to normal state, which results in interrupt storm. Correct the interrupt trigger type.

---
 arch/arm/boot/dts/tegra30-cardhu.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/tegra30-cardhu.dtsi +1 -1
index d9dd11569d4b..448f1397e64a 100644
@@ -348,7 +348,7 @@ nct1008: temperature-sensor@4c {
 			reg = <0x4c>;
 			vcc-supply = <&sys_3v3_reg>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
 			#thermal-sensor-cells = <1>;
 		};
 
Signature · 1 line
2.32.0
#9 lore raw

PATCH v2 9/15 ARM: tegra: dalmore: Correct interrupt trigger type of temperature sensor

In reply to Dmitry Osipenko

The LM90 temperature sensor should use edge-triggered interrupt because LM90 hardware doesn't deassert interrupt line until temperature is back to normal state, which results in interrupt storm. Correct the interrupt trigger type.

---
 arch/arm/boot/dts/tegra114-dalmore.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/tegra114-dalmore.dts +1 -1
index c04162ddec3c..7fd901f8d39a 100644
@@ -788,7 +788,7 @@ temperature-sensor@4c {
 			reg = <0x4c>;
 			vcc-supply = <&palmas_ldo6_reg>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_EDGE_FALLING>;
 		};
 	};
 
Signature · 1 line
2.32.0
#10 lore raw

PATCH v2 10/15 ARM: tegra: jetson-tk1: Correct interrupt trigger type of temperature sensor

In reply to Dmitry Osipenko

The LM90 temperature sensor should use edge-triggered interrupt because LM90 hardware doesn't deassert interrupt line until temperature is back to normal state, which results in interrupt storm. Correct the interrupt trigger type.

---
 arch/arm/boot/dts/tegra124-jetson-tk1.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/tegra124-jetson-tk1.dts +1 -1
index 414cd1cafa7f..35ab296408e1 100644
@@ -1427,7 +1427,7 @@ temperature-sensor@4c {
 			compatible = "ti,tmp451";
 			reg = <0x4c>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_EDGE_FALLING>;
 		};
 
 		eeprom@56 {
Signature · 1 line
2.32.0
#11 lore raw

PATCH v2 11/15 ARM: tegra: acer-a500: Remove bogus USB VBUS regulators

In reply to Dmitry Osipenko

The configuration of USB VBUS regulators was borrowed from downstream kernel, which is incorrect because the corresponding GPIOs are connected to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board schematics. USB works fine with both GPIOs being disabled, so remove the bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed 5v system regulator and device-mode USB1 doesn't have VBUS switches.

---
 .../boot/dts/tegra20-acer-a500-picasso.dts    | 25 +------------------
 1 file changed, 1 insertion(+), 24 deletions(-)
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +1 -24
index 4897079680bd..c385b13d4faa 100644
@@ -723,7 +723,6 @@ usb-phy@c5000000 {
 		nvidia,xcvr-setup-use-fuses;
 		nvidia,xcvr-lsfslew = <2>;
 		nvidia,xcvr-lsrslew = <2>;
-		vbus-supply = <&vdd_vbus1>;
 	};
 
 	usb@c5008000 {
@@ -735,7 +734,7 @@ usb-phy@c5008000 {
 		nvidia,xcvr-setup-use-fuses;
 		nvidia,xcvr-lsfslew = <2>;
 		nvidia,xcvr-lsrslew = <2>;
-		vbus-supply = <&vdd_vbus3>;
+		vbus-supply = <&vdd_5v0_sys>;
 	};
 
 	brcm_wifi_pwrseq: wifi-pwrseq {
@@ -995,28 +994,6 @@ vdd_pnl: regulator@3 {
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_vbus1: regulator@4 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_usb1_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-		gpio = <&gpio TEGRA_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		vin-supply = <&vdd_5v0_sys>;
-	};
-
-	vdd_vbus3: regulator@5 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_usb3_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-		gpio = <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		vin-supply = <&vdd_5v0_sys>;
-	};
-
 	sound {
 		compatible = "nvidia,tegra-audio-wm8903-picasso",
 			     "nvidia,tegra-audio-wm8903";
Signature · 1 line
2.32.0
#12 lore raw

PATCH v2 12/15 ARM: tegra: acer-a500: Add power supplies to accelerometer

In reply to Dmitry Osipenko

Add power supplies to accelerometer node, for completeness.

---
 arch/arm/boot/dts/tegra20-acer-a500-picasso.dts | 3 +++
 1 file changed, 3 insertions(+)
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +3 -0
index c385b13d4faa..7f20ea506803 100644
@@ -482,6 +482,9 @@ accelerometer@f {
 					interrupt-parent = <&gpio>;
 					interrupts = <TEGRA_GPIO(S, 7) IRQ_TYPE_EDGE_RISING>;
 
+					vdd-supply   = <&vdd_1v8_sys>;
+					vddio-supply = <&vdd_1v8_sys>;
+
 					mount-matrix =	 "0",  "1",  "0",
 							 "1",  "0",  "0",
 							 "0",  "0", "-1";
Signature · 1 line
2.32.0
#13 lore raw

PATCH v2 13/15 ARM: tegra: acer-a500: Use verbose variant of atmel,wakeup-method value

In reply to Dmitry Osipenko

The verbose variant of the atmel,wakeup-method value was lost when patch that added the property was merged because it conflicted with other patch, re-add it for consistency.

---
 arch/arm/boot/dts/tegra20-acer-a500-picasso.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +2 -1
index 7f20ea506803..87fef4cb630f 100644
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
+#include <dt-bindings/input/atmel-maxtouch.h>
 #include <dt-bindings/input/gpio-keys.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/thermal/thermal.h>
@@ -454,7 +455,7 @@ touchscreen@4c {
 			vdda-supply = <&vdd_3v3_sys>;
 			vdd-supply  = <&vdd_3v3_sys>;
 
-			atmel,wakeup-method = <1>;
+			atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>;
 		};
 
 		gyroscope@68 {
Signature · 1 line
2.32.0
#14 lore raw

PATCH v2 14/15 ARM: tegra: acer-a500: Improve thermal zones

In reply to Dmitry Osipenko

Use skin temperature for maintaining temperature that is suitable specifically for A500. Add CPU thermal zone that protects silicon. All these changes don't make a significant difference, but it is a more correct definition of thermal zones.

---
 .../boot/dts/tegra20-acer-a500-picasso.dts    | 55 ++++++++++++++++---
 1 file changed, 46 insertions(+), 9 deletions(-)
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +46 -9
index 87fef4cb630f..2280d75b66ab 100644
@@ -1029,11 +1029,48 @@ sound {
 	};
 
 	thermal-zones {
+		/*
+		 * NCT1008 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone is a simpler solution which prevents A500 from
+		 * getting too hot from a user's tactile perspective.
+		 * The CPU zone is intended to protect silicon from damage.
+		 */
+
 		skin-thermal {
 			polling-delay-passive = <1000>; /* milliseconds */
-			polling-delay = <0>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
 
 			thermal-sensors = <&nct1008 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* start throttling at 60C */
+					temperature = <60000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 70C */
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		cpu-thermal {
@@ -1043,24 +1080,24 @@ cpu-thermal {
 			thermal-sensors = <&nct1008 1>;
 
 			trips {
-				trip0: cpu-alert0 {
-					/* start throttling at 60C */
-					temperature = <60000>;
+				trip2: cpu-alert {
+					/* throttle at 85C until temperature drops to 84.8C */
+					temperature = <85000>;
 					hysteresis = <200>;
 					type = "passive";
 				};
 
-				trip1: cpu-crit {
-					/* shut down at 70C */
-					temperature = <70000>;
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
 
 			cooling-maps {
-				map0 {
-					trip = <&trip0>;
+				map1 {
+					trip = <&trip2>;
 					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
 							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
 				};
Signature · 1 line
2.32.0
#15 lore raw

PATCH v2 15/15 ARM: tegra: nexus7: Improve thermal zones

In reply to Dmitry Osipenko

Use skin temperature for maintaining temperature that is suitable specifically for Nexus 7. Add CPU thermal zone that protects silicon. All these changes don't make a significant difference, but it is a more correct definition of thermal zones.

---
 .../tegra30-asus-nexus7-grouper-common.dtsi   | 56 +++++++++++++++++--
 1 file changed, 52 insertions(+), 4 deletions(-)
arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi +52 -4
index 33985fca956f..9732cd6f20b7 100644
@@ -1255,21 +1255,34 @@ sound {
 	};
 
 	thermal-zones {
-		cpu-thermal {
+		/*
+		 * NCT72 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone is a simpler solution which prevents Nexus 7
+		 * from getting too hot from a user's tactile perspective.
+		 * The CPU zone is intended to protect silicon from damage.
+		 */
+
+		skin-thermal {
 			polling-delay-passive = <1000>; /* milliseconds */
 			polling-delay = <5000>; /* milliseconds */
 
-			thermal-sensors = <&nct72 1>;
+			thermal-sensors = <&nct72 0>;
 
 			trips {
-				trip0: cpu-alert0 {
+				trip0: skin-alert {
 					/* throttle at 57C until temperature drops to 56.8C */
 					temperature = <57000>;
 					hysteresis = <200>;
 					type = "passive";
 				};
 
-				trip1: cpu-crit {
+				trip1: skin-crit {
 					/* shut down at 65C */
 					temperature = <65000>;
 					hysteresis = <2000>;
@@ -1289,5 +1302,40 @@ map0 {
 				};
 			};
 		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 85C until temperature drops to 84.8C */
+					temperature = <85000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
 	};
 };
Signature · 1 line
2.32.0
#16 lore raw
In reply to Dmitry Osipenko

From: Thierry Reding <[email protected]>

Quoted 10 lines · Dmitry Osipenko

This series:

- adds SoC thermal sensor node
- adds interrupt for LM90 to Ouya, AC100, Nexus 7 and A500 devices
- fixes interrupt of LM90 sensor for all boards
- removes bogus VBUS regulators from A500 device-tree
- improves thermal zones of Nexus 7 and A500 devices based on previous discussion with Daniel Lezcano [1]

[...]

Applied, thanks!

[01/15] ARM: tegra: Add SoC thermal sensor to Tegra30 device-trees

        commit: ffd8969c91000c5e914e3a6e9dd108b80a935910
[02/15] ARM: tegra: ouya: Add interrupt to temperature sensor node
        commit: 00786f61df89c45c83d04e07f4021acc8fb87287
[03/15] ARM: tegra: paz00: Add interrupt to temperature sensor node
        commit: a371e9698e8912ddae6cff65cb5bd068e45efe80
[04/15] ARM: tegra: nexus7: Add interrupt to temperature sensor node
        commit: 4eb121af6184dcbae39438a4e6a5cfbac820cdd4
[05/15] ARM: tegra: acer-a500: Add interrupt to temperature sensor node
        commit: c626fd7eeb11934af7b59b330885ff8f96e2c2a0
[06/15] ARM: tegra: nyan: Correct interrupt trigger type of temperature sensor
        commit: 303e2f343403472f3a8421bdd9f62525117507d7
[07/15] ARM: tegra: apalis: Correct interrupt trigger type of temperature sensor
        commit: 61f8c4f6eefb1f5053ba208c872bceac057747ff
[08/15] ARM: tegra: cardhu: Correct interrupt trigger type of temperature sensor
        commit: ad86e473e1f3a7faa034535a91c9e594dd038830
[09/15] ARM: tegra: dalmore: Correct interrupt trigger type of temperature sensor
        commit: 0a6e9f9cc27be904f32ed40742f3b74a8fc2690d
[10/15] ARM: tegra: jetson-tk1: Correct interrupt trigger type of temperature sensor
        commit: 3970dc6444c5902463b50b10f04d3b0f576077bf
[11/15] ARM: tegra: acer-a500: Remove bogus USB VBUS regulators
        commit: 0c3136565b64e6e90ab5f9bd6b6c12d5b506c335
[12/15] ARM: tegra: acer-a500: Add power supplies to accelerometer
        commit: ebfbd63602b036f523514c48b5d1d36bef481d51
[13/15] ARM: tegra: acer-a500: Use verbose variant of atmel,wakeup-method value
        commit: 0cae833ff5187f9f629ef8b97543eb24d2c64faa
[14/15] ARM: tegra: acer-a500: Improve thermal zones
        commit: d97a74513cec1e378de9ffb6e5f512703db447d4
[15/15] ARM: tegra: nexus7: Improve thermal zones
        commit: b3b3e68aaab6a7f233fbf05ec30ace9ddcb36e51

Best regards,

Signature · 1 line
Thierry Reding <[email protected]>