drm/panel: s6d27a1: Add driver for Samsung S6D27A1 display panel
Subsystems (5)
Markuss Broks
maintainerPATCH 1/1 drm/panel: s6d27a1: Add driver for Samsung S6D27A1 display panel
This adds a driver for Samsung S6D27A1 display controller and panel. This panel is found in the Samsung GT-I8160 mobile phone, and possibly some other mobile phones.
This display needs manufactrer commands to configure it to a working state; the commands used in this driver were taken from downstream driver by Gareth Phillips; sadly, there is almost no documentation on what they actually do.
This driver re-uses the DBI infrastructure to communicate with the display.
This driver is heavily based on WideChips WS2401 display controller driver by Linus Walleij and on other panel drivers for reference.
--- drivers/gpu/drm/panel/Kconfig | 8 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6d27a1.c | 342 ++++++++++++++++++ 3 files changed, 351 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6d27a1.c
drivers/gpu/drm/panel/Kconfig +8 -0
@@ -348,6 +348,14 @@ config DRM_PANEL_SAMSUNG_S6D16D0 depends on DRM_MIPI_DSI select VIDEOMODE_HELPERS +config DRM_PANEL_SAMSUNG_S6D27A1 + tristate "Samsung S6D27A1 DPI panel driver" + depends on OF && SPI && GPIOLIB + select DRM_MIPI_DBI + help + Say Y here if you want to enable support for the Samsung + S6D27A1 DPI 480x800 panel. + config DRM_PANEL_SAMSUNG_S6E3HA2 tristate "Samsung S6E3HA2 DSI video mode panel" depends on OF
drivers/gpu/drm/panel/Makefile +1 -0
@@ -35,6 +35,7 @@ obj-$(CONFIG_DRM_PANEL_RAYDIUM_RM68200) += panel-raydium-rm68200.o obj-$(CONFIG_DRM_PANEL_RONBO_RB070D30) += panel-ronbo-rb070d30.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D16D0) += panel-samsung-s6d16d0.o +obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D27A1) += panel-samsung-s6d27a1.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03) += panel-samsung-s6e63j0x03.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63M0) += panel-samsung-s6e63m0.o
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +342 -0
342 lines not on this page · raw message
Signature · 1 line
2.32.0
Hi Markuss,
just a random collection of minor things to fix.
Overall the driver looks good.
Sam
Quoted 5 lines · Markuss Broks
This adds a driver for Samsung S6D27A1 display controller and panel. This panel is found in the Samsung GT-I8160 mobile phone, and possibly some other mobile phones.
This display needs manufactrer commands to configure it to a working state;
fix spelling of manufactrer
Quoted 55 lines
the commands used in this driver were taken from downstream driver by Gareth Phillips; sadly, there is almost no documentation on what they actually do.
This driver re-uses the DBI infrastructure to communicate with the display.
This driver is heavily based on WideChips WS2401 display controller driver by Linus Walleij and on other panel drivers for reference.
Signed-off-by Markuss Broks <[email protected]>--- drivers/gpu/drm/panel/Kconfig | 8 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6d27a1.c | 342 ++++++++++++++++++ 3 files changed, 351 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6d27a1.cdrivers/gpu/drm/panel/Kconfig +8
-0@@ -348,6 +348,14 @@ config DRM_PANEL_SAMSUNG_S6D16D0 depends on DRM_MIPI_DSI select VIDEOMODE_HELPERS +config DRM_PANEL_SAMSUNG_S6D27A1 + tristate "Samsung S6D27A1 DPI panel driver" + depends on OF && SPI && GPIOLIB + select DRM_MIPI_DBI + help + Say Y here if you want to enable support for the Samsung + S6D27A1 DPI 480x800 panel. + config DRM_PANEL_SAMSUNG_S6E3HA2 tristate "Samsung S6E3HA2 DSI video mode panel" depends on OFdrivers/gpu/drm/panel/Makefile +1
-0@@ -35,6 +35,7 @@ obj-$(CONFIG_DRM_PANEL_RAYDIUM_RM68200) += panel-raydium-rm68200.o obj-$(CONFIG_DRM_PANEL_RONBO_RB070D30) += panel-ronbo-rb070d30.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D16D0) += panel-samsung-s6d16d0.o +obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D27A1) += panel-samsung-s6d27a1.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03) += panel-samsung-s6e63j0x03.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63M0) += panel-samsung-s6e63m0.odrivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +1
-0@@ -0,0 +1,342 @@ +// SPDX-License-Identifier: GPL-2.0
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 11
Quoted 10 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +10
-0+/* +* Panel driver for the Samsung S6D27A1 480x800 DPI RGB panel. +* Found in the Samsung Galaxy Ace 2 GT-I8160 mobile phone. +*/ + +#include <drm/drm_modes.h> +#include <drm/drm_mipi_dbi.h> +#include <drm/drm_panel.h> + +#include <linux/backlight.h>
No backlight support - drop header.
Quoted 25 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +25
-0+#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/media-bus-format.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/regulator/consumer.h> +#include <linux/spi/spi.h> + +#include <video/mipi_display.h> + +#define S6D27A1_PASSWD_L2 0xF0/* Password Command for Level 2 Control */ +#define S6D27A1_RESCTL 0xB3/* Resolution Select Control */ +#define S6D27A1_PANELCTL2 0xB4/* ASG Signal Control */ +#define S6D27A1_READID1 0xDA/* Read panel ID 1 */ +#define S6D27A1_READID2 0xDB/* Read panel ID 2 */ +#define S6D27A1_READID3 0xDC/* Read panel ID 3 */ +#define S6D27A1_DISPCTL 0xF2/* Display Control */ +#define S6D27A1_MANPWR 0xF3/* Manual Control */ +#define S6D27A1_PWRCTL1 0xF4/* Power Control */ +#define S6D27A1_SRCCTL 0xF6/* Source Control */ +#define S6D27A1_PANELCTL 0xF7/* Panel Control*/ + +static const u8 s6d27a1_dbi_read_commands[] = {
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 46
Quoted 10 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +10
-0+S6D27A1_READID1 , +S6D27A1_READID2 , +S6D27A1_READID3 , + 0, /* sentinel */ +}; + +/** +* struct s6d27a1 - state container for a panel controlled by the WS2401 +* controller +*/
I see no value in kernel-doc style here.
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 55
Quoted 9 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +9
-0+struct s6d27a1 { +/** @dev: the container device */ +struct device *dev; +/** @dbi: the DBI bus abstraction handle */ +struct mipi_dbi dbi; +/** @panel: the DRM panel instance for this device */ +struct drm_panel panel; +/** @width: the width of this panel in mm */ +u32 width;
Drop, not used.
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 57
Quoted 2 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +2
-0+/** @height: the height of this panel in mm */ +u32 height;
Drop, not used.
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 61
Quoted 4 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +4
-0+/** @reset: reset GPIO line */ +struct gpio_desc *reset; +/** @regulators: VCCIO and VIO supply regulators */ +struct regulator_bulk_data regulators[2 ];
Names in comments does not match the code.
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 63
Quoted 2 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +2
-0+/** @bl: Backlight, if using internal backlight */ +struct backlight_device *bl;
Drop, not used.
Quoted 38 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +38
-0+}; + +static const struct drm_display_mode s6d27a1_480_800_mode = { +/* +* The vendor driver states that the S6D27A1 panel +* has a pixel clock frequency of 49920000 Hz / 2 = 24960000 Hz. +*/ + .clock =24960 , + .hdisplay =480 , + .hsync_start =480 +63 , + .hsync_end =480 +63 +2 , + .htotal =480 +63 +2 +63 , + .vdisplay =800 , + .vsync_start =800 +11 , + .vsync_end =800 +11 +2 , + .vtotal =800 +11 +2 +10 , + .width_mm =50 , + .height_mm =84 , + .flags =DRM_MODE_FLAG_NVSYNC |DRM_MODE_FLAG_NHSYNC , +}; + +static inline struct s6d27a1 *to_s6d27a1 (struct drm_panel *panel) +{ + return container_of(panel, struct s6d27a1, panel); +} + +#define s6d27a1_command(ctx, cmd, seq...) \ +({ \ + struct mipi_dbi *dbi = &ctx->dbi; \ + int ret; \ + ret = mipi_dbi_command(dbi, cmd, seq); \ + if (ret) { \ + dev_err(ctx->dev, "failure in writing command %02x\n", cmd); \ + } \ +}) + +static void s6d27a1_read_mtp_id (struct s6d27a1 *ctx) +{
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 111
Quoted 10 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +10
-0+struct mipi_dbi *dbi = &ctx->dbi; +u8 id1, id2, id3; +int ret; + + ret =mipi_dbi_command_read (dbi,S6D27A1_READID1 , &id1); +if (ret) { +dev_err (ctx->dev,"unable to read MTP ID 1\n" ); +return ; + } + ret =mipi_dbi_command_read (dbi,S6D27A1_READID2 , &id1);
Here you wanted to use id2
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 116
Quoted 5 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +5
-0+if (ret) { +dev_err (ctx->dev,"unable to read MTP ID 2\n" ); +return ; + } + ret =mipi_dbi_command_read (dbi,S6D27A1_READID3 , &id1);
Here you wanted to use id3
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 121
Quoted 5 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +5
-0+if (ret) { +dev_err (ctx->dev,"unable to read MTP ID 3\n" ); +return ; + } +dev_info (ctx->dev,"MTP ID: %02x %02x %02x\n" , id1, id2, id3);
Please verify that this prints the correct value to verify the above code.
Quoted 4 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +4
-0+} + +static int s6d27a1_power_on (struct s6d27a1 *ctx) +{
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 135
Quoted 10 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +10
-0+int ret; + +/* Power up */ + ret =regulator_bulk_enable (ARRAY_SIZE (ctx->regulators), + ctx->regulators); +if (ret) { +dev_err (ctx->dev,"failed to enable regulators: %d\n" , ret); +return ret; + } +msleep (20 );
Add empty line after closing '}'
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 144
Quoted 10 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +9
-0+ +/* Assert reset >=1 ms */ +gpiod_set_value_cansleep (ctx->reset,1 ); +usleep_range (1000 ,5000 ); +/* De-assert reset */ +gpiod_set_value_cansleep (ctx->reset,0 ); +/* Wait >= 10 ms */ +msleep (20 ); +dev_dbg (ctx->dev,"de-asserted RESET\n" );
Looks like some debug leftover that can be dropped.
Quoted 79 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +79
-0+ +/* +* Exit sleep mode and initialize display - some hammering is +* necessary. +*/ +s6d27a1_command (ctx,MIPI_DCS_EXIT_SLEEP_MODE ); +s6d27a1_command (ctx,MIPI_DCS_EXIT_SLEEP_MODE ); +msleep (50 ); + +/* Magic to unlock level 2 control of the display */ +s6d27a1_command (ctx,S6D27A1_PASSWD_L2 ,0x5A ,0x5A ); + +/* Configure resolution to 480RGBx800 */ +s6d27a1_command (ctx,S6D27A1_RESCTL ,0x22 ); + +s6d27a1_command (ctx,S6D27A1_PANELCTL2 ,0x00 ,0x02 ,0x03 ,0x04 ,0x05 ,0x08 ,0x00 ,0x0c ); + +s6d27a1_command (ctx,S6D27A1_MANPWR ,0x01 ,0x00 ,0x00 ,0x08 ,0x08 ,0x02 ,0x00 ); + +s6d27a1_command (ctx,S6D27A1_DISPCTL ,0x19 ,0x00 ,0x08 ,0x0D ,0x03 ,0x41 ,0x3F ); + +s6d27a1_command (ctx,S6D27A1_PWRCTL1 ,0x00 ,0x00 ,0x00 ,0x00 ,0x55 , +0x44 ,0x05 ,0x88 ,0x4B ,0x50 ); + +s6d27a1_command (ctx,S6D27A1_SRCCTL ,0x03 ,0x09 ,0x8A ,0x00 ,0x01 ,0x16 ); + +s6d27a1_command (ctx,S6D27A1_PANELCTL ,0x00 ,0x05 ,0x06 ,0x07 ,0x08 , +0x01 ,0x09 ,0x0D ,0x0A ,0x0E , +0x0B ,0x0F ,0x0C ,0x10 ,0x01 , +0x11 ,0x12 ,0x13 ,0x14 ,0x05 , +0x06 ,0x07 ,0x08 ,0x01 ,0x09 , +0x0D ,0x0A ,0x0E ,0x0B ,0x0F , +0x0C ,0x10 ,0x01 ,0x11 ,0x12 , +0x13 ,0x14 ); + +/* lock the level 2 control */ +s6d27a1_command (ctx,S6D27A1_PASSWD_L2 ,0xA5 ,0xA5 ); + +s6d27a1_read_mtp_id (ctx); + +return 0 ; +} + +static int s6d27a1_power_off (struct s6d27a1 *ctx) +{ +/* Go into RESET and disable regulators */ +gpiod_set_value_cansleep (ctx->reset,1 ); +return regulator_bulk_disable (ARRAY_SIZE (ctx->regulators), + ctx->regulators); +} + +static int s6d27a1_unprepare (struct drm_panel *panel) +{ +struct s6d27a1 *ctx =to_s6d27a1 (panel); + +s6d27a1_command (ctx,MIPI_DCS_ENTER_SLEEP_MODE ); +msleep (120 ); +return s6d27a1_power_off (to_s6d27a1 (panel)); +} + +static int s6d27a1_disable (struct drm_panel *panel) +{ +struct s6d27a1 *ctx =to_s6d27a1 (panel); + +s6d27a1_command (ctx,MIPI_DCS_SET_DISPLAY_OFF ); +msleep (25 ); + +return 0 ; +} + +static int s6d27a1_prepare (struct drm_panel *panel) +{ +return s6d27a1_power_on (to_s6d27a1 (panel)); +} + +static int s6d27a1_enable (struct drm_panel *panel) +{ +struct s6d27a1 *ctx =to_s6d27a1 (panel); +
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 233
Quoted 10 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +10
-0+s6d27a1_command (ctx,MIPI_DCS_SET_DISPLAY_ON ); + +return 0 ; +} + +/** +* s6d27a1_get_modes() - return the mode +* @panel: the panel to get the mode for +* @connector: reference to the central DRM connector control structure +*/
Kernel-doc here seems irrelevant. And drop the descriptions of parameters too.
Quoted 36 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +36
-0+static int s6d27a1_get_modes (struct drm_panel *panel, +struct drm_connector *connector) +{ +struct s6d27a1 *ctx =to_s6d27a1 (panel); +struct drm_display_mode *mode; +static const u32 bus_format =MEDIA_BUS_FMT_RGB888_1X24 ; + + mode =drm_mode_duplicate (connector->dev, &s6d27a1_480_800_mode); +if (!mode) { +dev_err (ctx->dev,"failed to add mode\n" ); +return -ENOMEM ; + } + + connector->display_info.bpc =8 ; + connector->display_info.width_mm = mode->width_mm; + connector->display_info.height_mm = mode->height_mm; + connector->display_info.bus_flags = +DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE ; +drm_display_info_set_bus_formats (&connector->display_info, + &bus_format,1 ); + +drm_mode_set_name (mode); + mode->type =DRM_MODE_TYPE_DRIVER |DRM_MODE_TYPE_PREFERRED ; + +drm_mode_probed_add (connector, mode); + +return 1 ; +} + +static const struct drm_panel_funcs s6d27a1_drm_funcs = { + .disable = s6d27a1_disable, + .unprepare = s6d27a1_unprepare, + .prepare = s6d27a1_prepare, + .enable = s6d27a1_enable, + .get_modes = s6d27a1_get_modes, +};
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 279
Quoted 10 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +10
-0+ +static int s6d27a1_probe (struct spi_device *spi) +{ +struct device *dev = &spi->dev; +struct s6d27a1 *ctx; +int ret; + + ctx =devm_kzalloc (dev,sizeof (*ctx),GFP_KERNEL ); +if (!ctx) +return -ENOMEM ;
Add empty line here
Quoted 13 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +13
-0+ ctx->dev = dev; + +/* +* VCI is the analog voltage supply +* VCCIO is the digital I/O voltage supply +*/ + ctx->regulators[0 ].supply ="vci" ; + ctx->regulators[1 ].supply ="vccio" ; + ret =devm_regulator_bulk_get (dev, +ARRAY_SIZE (ctx->regulators), + ctx->regulators); +if (ret) +return dev_err_probe (dev, ret,"failed to get regulators\n" );
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 302
Quoted 10 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +10
-0+ + ctx->reset =devm_gpiod_get (dev,"reset" ,GPIOD_OUT_HIGH ); +if (IS_ERR (ctx->reset)) { + ret =PTR_ERR (ctx->reset); +return dev_err_probe (dev, ret,"no RESET GPIO\n" ); + } + + ret =mipi_dbi_spi_init (spi, &ctx->dbi,NULL ); +if (ret) +return dev_err_probe (dev, ret,"MIPI DBI init failed\n" );
Add empty line here
Quoted 14 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +14
-0+ ctx->dbi.read_commands = s6d27a1_dbi_read_commands; + +drm_panel_init (&ctx->panel, dev, &s6d27a1_drm_funcs, +DRM_MODE_CONNECTOR_DPI ); + +spi_set_drvdata (spi, ctx); + +drm_panel_add (&ctx->panel); +dev_dbg (dev,"added panel\n" ); + +return 0 ; +} + +static int s6d27a1_remove (struct spi_device *spi)
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 326
Quoted 10 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +10
-0+{ +struct s6d27a1 *ctx =spi_get_drvdata (spi); + +drm_panel_remove (&ctx->panel); +return 0 ; +} + +static const struct of_device_id s6d27a1_match[] = { + { .compatible ="samsung,s6d27a1" , }, + {},
Write as
{ /* sentinel */ },Quoted 18 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +16
-0+}; +MODULE_DEVICE_TABLE (of, s6d27a1_match); + +static struct spi_driver s6d27a1_driver = { + .probe = s6d27a1_probe, + .remove = s6d27a1_remove, + .driver = { + .name ="s6d27a1-panel" , + .of_match_table = s6d27a1_match, + }, +}; +module_spi_driver (s6d27a1_driver); + +MODULE_AUTHOR ("Markuss Broks <[email protected]>" ); +MODULE_DESCRIPTION ("Samsung S6D27A1 panel driver" ); +MODULE_LICENSE ("GPL v2" );Signature · 1 line
2.32.0
Markuss Broks
maintainerPATCH v2 1/1 drm/panel: s6d27a1: Add driver for Samsung S6D27A1 display panel
This adds a driver for Samsung S6D27A1 display controller and panel. This panel is found in the Samsung GT-I8160 mobile phone, and possibly some other mobile phones.
This display needs manufacturer commands to configure it to a working state; the commands used in this driver were taken from downstream driver by Gareth Phillips; sadly, there is almost no documentation on what they actually do.
This driver re-uses the DBI infrastructure to communicate with the display.
This driver is heavily based on WideChips WS2401 display controller driver by Linus Walleij and on other panel drivers for reference.
--- drivers/gpu/drm/panel/Kconfig | 8 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6d27a1.c | 323 ++++++++++++++++++ 3 files changed, 332 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6d27a1.c
drivers/gpu/drm/panel/Kconfig +8 -0
@@ -348,6 +348,14 @@ config DRM_PANEL_SAMSUNG_S6D16D0 depends on DRM_MIPI_DSI select VIDEOMODE_HELPERS +config DRM_PANEL_SAMSUNG_S6D27A1 + tristate "Samsung S6D27A1 DPI panel driver" + depends on OF && SPI && GPIOLIB + select DRM_MIPI_DBI + help + Say Y here if you want to enable support for the Samsung + S6D27A1 DPI 480x800 panel. + config DRM_PANEL_SAMSUNG_S6E3HA2 tristate "Samsung S6E3HA2 DSI video mode panel" depends on OF
drivers/gpu/drm/panel/Makefile +1 -0
@@ -35,6 +35,7 @@ obj-$(CONFIG_DRM_PANEL_RAYDIUM_RM68200) += panel-raydium-rm68200.o obj-$(CONFIG_DRM_PANEL_RONBO_RB070D30) += panel-ronbo-rb070d30.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D16D0) += panel-samsung-s6d16d0.o +obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D27A1) += panel-samsung-s6d27a1.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03) += panel-samsung-s6e63j0x03.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63M0) += panel-samsung-s6e63m0.o
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +323 -0
323 lines not on this page · raw message
Signature · 1 line
2.32.0
Hi Markuss,
Quoted 9 lines · Markuss Broks
This adds a driver for Samsung S6D27A1 display controller and panel. This panel is found in the Samsung GT-I8160 mobile phone, and possibly some other mobile phones.
This display needs manufacturer commands to configure it to a working state; the commands used in this driver were taken from downstream driver by Gareth Phillips; sadly, there is almost no documentation on what they actually do.
Quoted 6 lines
This driver re-uses the DBI infrastructure to communicate with the display.
This driver is heavily based on WideChips WS2401 display controller driver by Linus Walleij and on other panel drivers for reference.
Signed-off-by Markuss Broks <[email protected]>
Thnaks for the very quick response.
Please provide a changelog so we can follow what has changed. Sometimes we revisit patches week and 100 patches later and cannot remember any feedback.
Like for example (my style):
v3:
- fixed checkpatch warnings (sam)
- ...
v2:
- dropped backlight (sam)
- dropped kernel-doc (sam)
- bla bla (someone)
There are many different styles - pick one.
Also two other things.
checkpatch --strict reports a few issues to be fixed:
total: 0 errors, 5 warnings, 6 checks, 344 lines checked
One of them is a missing binding!
And the patch fails to apply. Please rebase on top of -next or drm-misc-next.
Thanks in advance!
Sam
Markuss Broks
maintainercover Add support for Samsung S6D27A1 display panel
Add support for Samsung Mobile Displays(SMD) Samsung S6D27A1 panel. This display panel is used on Samsung mobile devices such as Samsung Galaxy Ace 2 (GT-I8160) also known as Codina.
Markuss Broks (2):
drm/panel: Add DT bindings for Samsung S6D27A1 display panel drm/panel: s6d27a1: Add driver for Samsung S6D27A1 display panel
.../display/panel/samsung,s6d27a1.yaml | 97 ++++++ drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6d27a1.c | 323 ++++++++++++++++++ 4 files changed, 432 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6d27a1.c
Signature · 1 line
2.32.0
Markuss Broks
maintainerPATCH 1/2 drm/panel: Add DT bindings for Samsung S6D27A1 display panel
This adds device-tree bindings for the Samsung S6D27A1 RGB DPI display panel.
--- .../display/panel/samsung,s6d27a1.yaml | 97 +++++++++++++++++++ 1 file changed, 97 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml
Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml new file +97 -0
@@ -0,0 +1,97 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/samsung,s6d27a1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S6D27A1 display panel + +description: The S6D27A1 is a 480x800 DPI display panel from Samsung Mobile + Displays (SMD). The panel must obey the rules for a SPI slave device + as specified in spi/spi-controller.yaml + +maintainers: + - Markuss Broks <[email protected]> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: samsung,s6d27a1 + + reg: true + + interrupts: + description: provides an optional ESD (electrostatic discharge) + interrupt that signals abnormalities in the display hardware. + This can also be raised for other reasons like erroneous + configuration. + maxItems: 1 + + reset-gpios: true + + vci-supply: + description: regulator that supplies the VCI analog voltage + usually around 3.0 V + + vccio-supply: + description: regulator that supplies the VCCIO voltage usually + around 1.8 V + + backlight: true + + spi-cpha: true + + spi-cpol: true + + spi-max-frequency: + maximum: 1200000 + + port: true + +required: + - compatible + - reg + - spi-cpha + - spi-cpol + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + compatible = "spi-gpio"; + sck-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + miso-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; + cs-gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; + num-chipselects = <1>; + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "samsung,s6d27a1"; + spi-max-frequency = <1200000>; + spi-cpha; + spi-cpol; + reg = <0>; + vci-supply = <&lcd_3v0_reg>; + vccio-supply = <&lcd_1v8_reg>; + reset-gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio>; + interrupts = <5 IRQ_TYPE_EDGE_RISING>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + }; + +...
Signature · 1 line
2.32.0
Re: [PATCH 1/2] drm/panel: Add DT bindings for Samsung S6D27A1 display panel
Hi Markuss,
Quoted 64 lines · Markuss Broks
This adds device-tree bindings for the Samsung S6D27A1 RGB DPI display panel.
Signed-off-by Markuss Broks <[email protected]>--- .../display/panel/samsung,s6d27a1.yaml | 97 +++++++++++++++++++ 1 file changed, 97 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yamlDocumentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml new file +49
-0@@ -0,0 +1,97 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/samsung,s6d27a1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S6D27A1 display panel + +description: The S6D27A1 is a 480x800 DPI display panel from Samsung Mobile + Displays (SMD). The panel must obey the rules for a SPI slave device + as specified in spi/spi-controller.yaml + +maintainers: + - Markuss Broks <[email protected]> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: samsung,s6d27a1 + + reg: true + + interrupts: + description: provides an optional ESD (electrostatic discharge) + interrupt that signals abnormalities in the display hardware. + This can also be raised for other reasons like erroneous + configuration. + maxItems: 1 + + reset-gpios: true + + vci-supply: + description: regulator that supplies the VCI analog voltage + usually around 3.0 V + + vccio-supply: + description: regulator that supplies the VCCIO voltage usually + around 1.8 V + + backlight: true + + spi-cpha: true + + spi-cpol: true + + spi-max-frequency: + maximum: 1200000
Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml line 58
Quoted 10 lines
Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml new file +9
-0+ + port: true + +required: + - compatible + - reg + - spi-cpha + - spi-cpol + - port
Do the HW really require the above three properties?
Can the HW work without a supply (hint: I think vci-supply and vccio-supply are required)
Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml
Quoted 2 lines
Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml new file +2
-0+ +additionalProperties: false
As this device sits on the SPI bus you need to use:
unevaluatedProterties: false
(Check spelling from other bindings)
This allows DT files to add more spi related properties, but do not allow DT files to add unknown properties.
With the current scheme you restrict the DT file to only the three mentioned SPI properties that may be OK for your HW but maybe not OK for the next HW using the same panel.
Sam
Quoted 39 lines
Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml new file +37
-0+ +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + compatible = "spi-gpio"; + sck-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + miso-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; + cs-gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; + num-chipselects = <1>; + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "samsung,s6d27a1"; + spi-max-frequency = <1200000>; + spi-cpha; + spi-cpol; + reg = <0>; + vci-supply = <&lcd_3v0_reg>; + vccio-supply = <&lcd_1v8_reg>; + reset-gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio>; + interrupts = <5 IRQ_TYPE_EDGE_RISING>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + }; + +...Signature · 1 line
2.32.0
Markuss Broks
maintainerPATCH 2/2 drm/panel: s6d27a1: Add driver for Samsung S6D27A1 display panel
In reply to Markuss BroksThis adds a driver for Samsung S6D27A1 display controller and panel. This panel is found in the Samsung GT-I8160 mobile phone, and possibly some other mobile phones.
This display needs manufacturer commands to configure it; the commands used in this driver were taken from downstream driver by Gareth Phillips; sadly, there is almost no documentation on what they actually do.
This driver re-uses the DBI infrastructure to communicate with the display.
This driver is heavily based on WideChips WS2401 display controller driver by Linus Walleij and on other panel drivers for reference.
v2 -> v3:
fixed checkpatch warnings - not sure about MAINTAINERS, should I put my name up there?
--- drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6d27a1.c | 323 ++++++++++++++++++ 3 files changed, 335 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6d27a1.c
drivers/gpu/drm/panel/Kconfig +11 -0
@@ -392,6 +392,17 @@ config DRM_PANEL_SAMSUNG_S6D16D0 depends on DRM_MIPI_DSI select VIDEOMODE_HELPERS +config DRM_PANEL_SAMSUNG_S6D27A1 + tristate "Samsung S6D27A1 DPI panel driver" + depends on OF && SPI && GPIOLIB + select DRM_MIPI_DBI + help + Say Y here if you want to enable support for the Samsung + S6D27A1 DPI 480x800 panel. + + This panel can be found in Samsung Galaxy Ace 2 + GT-I8160 mobile phone. + config DRM_PANEL_SAMSUNG_S6E3HA2 tristate "Samsung S6E3HA2 DSI video mode panel" depends on OF
drivers/gpu/drm/panel/Makefile +1 -0
@@ -39,6 +39,7 @@ obj-$(CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20) += panel-samsung-atna33xc20.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_DB7430) += panel-samsung-db7430.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D16D0) += panel-samsung-s6d16d0.o +obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D27A1) += panel-samsung-s6d27a1.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03) += panel-samsung-s6e63j0x03.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63M0) += panel-samsung-s6e63m0.o
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +323 -0
323 lines not on this page · raw message
Signature · 1 line
2.32.0
Hi Markuss,
Quoted 11 lines · Markuss Broks
This adds a driver for Samsung S6D27A1 display controller and panel. This panel is found in the Samsung GT-I8160 mobile phone, and possibly some other mobile phones.
This display needs manufacturer commands to configure it; the commands used in this driver were taken from downstream driver by Gareth Phillips; sadly, there is almost no documentation on what they actually do.
This driver re-uses the DBI infrastructure to communicate with the display.
Quoted 8 lines
This driver is heavily based on WideChips WS2401 display controller driver by Linus Walleij and on other panel drivers for reference.
Signed-off-by Markuss Broks <[email protected]>v2 -> v3:
fixed checkpatch warnings - not sure aboutMAINTAINERS, should I put my name up there?
You made lots of other changes..
Yes, MAINTAINERS would be great so you get mails when something is updated. This allows you to verify refactoring changes or bug fixes for example.
For a single driver you can realy on someone else to apply patches, no need to deal with drm-misc etc. for that.
A few details in the following, but driver is almost there.
Sam
Quoted 119 lines
--- drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6d27a1.c | 323 ++++++++++++++++++ 3 files changed, 335 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6d27a1.cdrivers/gpu/drm/panel/Kconfig +11
-0@@ -392,6 +392,17 @@ config DRM_PANEL_SAMSUNG_S6D16D0 depends on DRM_MIPI_DSI select VIDEOMODE_HELPERS +config DRM_PANEL_SAMSUNG_S6D27A1 + tristate "Samsung S6D27A1 DPI panel driver" + depends on OF && SPI && GPIOLIB + select DRM_MIPI_DBI + help + Say Y here if you want to enable support for the Samsung + S6D27A1 DPI 480x800 panel. + + This panel can be found in Samsung Galaxy Ace 2 + GT-I8160 mobile phone. + config DRM_PANEL_SAMSUNG_S6E3HA2 tristate "Samsung S6E3HA2 DSI video mode panel" depends on OFdrivers/gpu/drm/panel/Makefile +1
-0@@ -39,6 +39,7 @@ obj-$(CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20) += panel-samsung-atna33xc20.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_DB7430) += panel-samsung-db7430.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D16D0) += panel-samsung-s6d16d0.o +obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D27A1) += panel-samsung-s6d27a1.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03) += panel-samsung-s6e63j0x03.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63M0) += panel-samsung-s6e63m0.odrivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +72
-0@@ -0,0 +1,323 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Panel driver for the Samsung S6D27A1 480x800 DPI RGB panel. +* Found in the Samsung Galaxy Ace 2 GT-I8160 mobile phone. +*/ + +#include <drm/drm_modes.h> +#include <drm/drm_mipi_dbi.h> +#include <drm/drm_panel.h> + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/media-bus-format.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/regulator/consumer.h> +#include <linux/spi/spi.h> + +#include <video/mipi_display.h> + +#define S6D27A1_PASSWD_L2 0xF0/* Password Command for Level 2 Control */ +#define S6D27A1_RESCTL 0xB3/* Resolution Select Control */ +#define S6D27A1_PANELCTL2 0xB4/* ASG Signal Control */ +#define S6D27A1_READID1 0xDA/* Read panel ID 1 */ +#define S6D27A1_READID2 0xDB/* Read panel ID 2 */ +#define S6D27A1_READID3 0xDC/* Read panel ID 3 */ +#define S6D27A1_DISPCTL 0xF2/* Display Control */ +#define S6D27A1_MANPWR 0xF3/* Manual Control */ +#define S6D27A1_PWRCTL1 0xF4/* Power Control */ +#define S6D27A1_SRCCTL 0xF6/* Source Control */ +#define S6D27A1_PANELCTL 0xF7/* Panel Control*/ + +static const u8 s6d27a1_dbi_read_commands[] = { +S6D27A1_READID1 , +S6D27A1_READID2 , +S6D27A1_READID3 , +0 ,/* sentinel */ +}; + +struct s6d27a1 { +struct device *dev; +struct mipi_dbi dbi; +struct drm_panel panel; +struct gpio_desc *reset; +struct regulator_bulk_data regulators[2 ]; +}; + +static const struct drm_display_mode s6d27a1_480_800_mode = { +/* +* The vendor driver states that the S6D27A1 panel +* has a pixel clock frequency of 49920000 Hz / 2 = 24960000 Hz. +*/ + .clock =24960 , + .hdisplay =480 , + .hsync_start =480 +63 , + .hsync_end =480 +63 +2 , + .htotal =480 +63 +2 +63 , + .vdisplay =800 , + .vsync_start =800 +11 , + .vsync_end =800 +11 +2 , + .vtotal =800 +11 +2 +10 , + .width_mm =50 , + .height_mm =84 , + .flags =DRM_MODE_FLAG_NVSYNC |DRM_MODE_FLAG_NHSYNC , +}; + +static inline struct s6d27a1 *to_s6d27a1 (struct drm_panel *panel) +{ + return container_of(panel, struct s6d27a1, panel); +}
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 82
Quoted 10 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +10
-0+ +#define s6d27a1_command(ctx, cmd, seq...) \ +({ \ + struct mipi_dbi *dbi = &ctx->dbi; \ + int ret; \ + ret = mipi_dbi_command(dbi, cmd, seq); \ + if (ret) { \ + dev_err(ctx->dev, "failure in writing command %02x\n", cmd); \ + } \ +})
This does not error out like other panel drivers. I think this is wrong.
Quoted 200 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +200
-0+ +static void s6d27a1_read_mtp_id (struct s6d27a1 *ctx) +{ +struct mipi_dbi *dbi = &ctx->dbi; +u8 id1, id2, id3; +int ret; + + ret =mipi_dbi_command_read (dbi,S6D27A1_READID1 , &id1); +if (ret) { +dev_err (ctx->dev,"unable to read MTP ID 1\n" ); +return ; + } + ret =mipi_dbi_command_read (dbi,S6D27A1_READID2 , &id2); +if (ret) { +dev_err (ctx->dev,"unable to read MTP ID 2\n" ); +return ; + } + ret =mipi_dbi_command_read (dbi,S6D27A1_READID3 , &id3); +if (ret) { +dev_err (ctx->dev,"unable to read MTP ID 3\n" ); +return ; + } +dev_info (ctx->dev,"MTP ID: %02x %02x %02x\n" , id1, id2, id3); +} + +static int s6d27a1_power_on (struct s6d27a1 *ctx) +{ +int ret; + +/* Power up */ + ret =regulator_bulk_enable (ARRAY_SIZE (ctx->regulators), + ctx->regulators); +if (ret) { +dev_err (ctx->dev,"failed to enable regulators: %d\n" , ret); +return ret; + } + +msleep (20 ); + +/* Assert reset >=1 ms */ +gpiod_set_value_cansleep (ctx->reset,1 ); +usleep_range (1000 ,5000 ); +/* De-assert reset */ +gpiod_set_value_cansleep (ctx->reset,0 ); +/* Wait >= 10 ms */ +msleep (20 ); + +/* +* Exit sleep mode and initialize display - some hammering is +* necessary. +*/ +s6d27a1_command (ctx,MIPI_DCS_EXIT_SLEEP_MODE ); +s6d27a1_command (ctx,MIPI_DCS_EXIT_SLEEP_MODE ); +msleep (50 ); + +/* Magic to unlock level 2 control of the display */ +s6d27a1_command (ctx,S6D27A1_PASSWD_L2 ,0x5A ,0x5A ); + +/* Configure resolution to 480RGBx800 */ +s6d27a1_command (ctx,S6D27A1_RESCTL ,0x22 ); + +s6d27a1_command (ctx,S6D27A1_PANELCTL2 ,0x00 ,0x02 ,0x03 ,0x04 ,0x05 ,0x08 ,0x00 ,0x0c ); + +s6d27a1_command (ctx,S6D27A1_MANPWR ,0x01 ,0x00 ,0x00 ,0x08 ,0x08 ,0x02 ,0x00 ); + +s6d27a1_command (ctx,S6D27A1_DISPCTL ,0x19 ,0x00 ,0x08 ,0x0D ,0x03 ,0x41 ,0x3F ); + +s6d27a1_command (ctx,S6D27A1_PWRCTL1 ,0x00 ,0x00 ,0x00 ,0x00 ,0x55 , +0x44 ,0x05 ,0x88 ,0x4B ,0x50 ); + +s6d27a1_command (ctx,S6D27A1_SRCCTL ,0x03 ,0x09 ,0x8A ,0x00 ,0x01 ,0x16 ); + +s6d27a1_command (ctx,S6D27A1_PANELCTL ,0x00 ,0x05 ,0x06 ,0x07 ,0x08 , +0x01 ,0x09 ,0x0D ,0x0A ,0x0E , +0x0B ,0x0F ,0x0C ,0x10 ,0x01 , +0x11 ,0x12 ,0x13 ,0x14 ,0x05 , +0x06 ,0x07 ,0x08 ,0x01 ,0x09 , +0x0D ,0x0A ,0x0E ,0x0B ,0x0F , +0x0C ,0x10 ,0x01 ,0x11 ,0x12 , +0x13 ,0x14 ); + +/* lock the level 2 control */ +s6d27a1_command (ctx,S6D27A1_PASSWD_L2 ,0xA5 ,0xA5 ); + +s6d27a1_read_mtp_id (ctx); + +return 0 ; +} + +static int s6d27a1_power_off (struct s6d27a1 *ctx) +{ +/* Go into RESET and disable regulators */ +gpiod_set_value_cansleep (ctx->reset,1 ); +return regulator_bulk_disable (ARRAY_SIZE (ctx->regulators), + ctx->regulators); +} + +static int s6d27a1_unprepare (struct drm_panel *panel) +{ +struct s6d27a1 *ctx =to_s6d27a1 (panel); + +s6d27a1_command (ctx,MIPI_DCS_ENTER_SLEEP_MODE ); +msleep (120 ); +return s6d27a1_power_off (to_s6d27a1 (panel)); +} + +static int s6d27a1_disable (struct drm_panel *panel) +{ +struct s6d27a1 *ctx =to_s6d27a1 (panel); + +s6d27a1_command (ctx,MIPI_DCS_SET_DISPLAY_OFF ); +msleep (25 ); + +return 0 ; +} + +static int s6d27a1_prepare (struct drm_panel *panel) +{ +return s6d27a1_power_on (to_s6d27a1 (panel)); +} + +static int s6d27a1_enable (struct drm_panel *panel) +{ +struct s6d27a1 *ctx =to_s6d27a1 (panel); + +s6d27a1_command (ctx,MIPI_DCS_SET_DISPLAY_ON ); + +return 0 ; +} + +static int s6d27a1_get_modes (struct drm_panel *panel, +struct drm_connector *connector) +{ +struct s6d27a1 *ctx =to_s6d27a1 (panel); +struct drm_display_mode *mode; +static const u32 bus_format =MEDIA_BUS_FMT_RGB888_1X24 ; + + mode =drm_mode_duplicate (connector->dev, &s6d27a1_480_800_mode); +if (!mode) { +dev_err (ctx->dev,"failed to add mode\n" ); +return -ENOMEM ; + } + + connector->display_info.bpc =8 ; + connector->display_info.width_mm = mode->width_mm; + connector->display_info.height_mm = mode->height_mm; + connector->display_info.bus_flags = +DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE ; +drm_display_info_set_bus_formats (&connector->display_info, + &bus_format,1 ); + +drm_mode_set_name (mode); + mode->type =DRM_MODE_TYPE_DRIVER |DRM_MODE_TYPE_PREFERRED ; + +drm_mode_probed_add (connector, mode); + +return 1 ; +} + +static const struct drm_panel_funcs s6d27a1_drm_funcs = { + .disable = s6d27a1_disable, + .unprepare = s6d27a1_unprepare, + .prepare = s6d27a1_prepare, + .enable = s6d27a1_enable, + .get_modes = s6d27a1_get_modes, +}; + +static int s6d27a1_probe (struct spi_device *spi) +{ +struct device *dev = &spi->dev; +struct s6d27a1 *ctx; +int ret; + + ctx =devm_kzalloc (dev,sizeof (*ctx),GFP_KERNEL ); +if (!ctx) +return -ENOMEM ; + + ctx->dev = dev; + +/* +* VCI is the analog voltage supply +* VCCIO is the digital I/O voltage supply +*/ + ctx->regulators[0 ].supply ="vci" ; + ctx->regulators[1 ].supply ="vccio" ; + ret =devm_regulator_bulk_get (dev, +ARRAY_SIZE (ctx->regulators), + ctx->regulators); +if (ret) +return dev_err_probe (dev, ret,"failed to get regulators\n" ); + + ctx->reset =devm_gpiod_get (dev,"reset" ,GPIOD_OUT_HIGH ); +if (IS_ERR (ctx->reset)) { + ret =PTR_ERR (ctx->reset); +return dev_err_probe (dev, ret,"no RESET GPIO\n" ); + } + + ret =mipi_dbi_spi_init (spi, &ctx->dbi,NULL ); +if (ret) +return dev_err_probe (dev, ret,"MIPI DBI init failed\n" );
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 292
Quoted 10 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +10
-0+ + ctx->dbi.read_commands = s6d27a1_dbi_read_commands; + +drm_panel_init (&ctx->panel, dev, &s6d27a1_drm_funcs, +DRM_MODE_CONNECTOR_DPI ); + +spi_set_drvdata (spi, ctx); + +drm_panel_add (&ctx->panel); +dev_dbg (dev,"added panel\n" );
Debug leftover that can be dropped.
Quoted 33 lines
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +31
-0+ +return 0 ; +} + +static int s6d27a1_remove (struct spi_device *spi) +{ +struct s6d27a1 *ctx =spi_get_drvdata (spi); + +drm_panel_remove (&ctx->panel); +return 0 ; +} + +static const struct of_device_id s6d27a1_match[] = { + { .compatible ="samsung,s6d27a1" , }, + {/* sentinel */ }, +}; +MODULE_DEVICE_TABLE (of, s6d27a1_match); + +static struct spi_driver s6d27a1_driver = { + .probe = s6d27a1_probe, + .remove = s6d27a1_remove, + .driver = { + .name ="s6d27a1-panel" , + .of_match_table = s6d27a1_match, + }, +}; +module_spi_driver (s6d27a1_driver); + +MODULE_AUTHOR ("Markuss Broks <[email protected]>" ); +MODULE_DESCRIPTION ("Samsung S6D27A1 panel driver" ); +MODULE_LICENSE ("GPL v2" );Signature · 1 line
2.32.0
Markuss Broks
maintainercover Add support for Samsung S6D27A1 display panel
Add support for Samsung Mobile Displays(SMD) Samsung S6D27A1 panel. This display panel is used on Samsung mobile devices such as Samsung Galaxy Ace 2 (GT-I8160) also known as Codina.
Markuss Broks (2):
drm/panel: Add DT bindings for Samsung S6D27A1 display panel drm/panel: s6d27a1: Add driver for Samsung S6D27A1 display panel
.../display/panel/samsung,s6d27a1.yaml | 97 ++++++ drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6d27a1.c | 323 ++++++++++++++++++ 4 files changed, 432 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6d27a1.c
Signature · 1 line
2.32.0
Markuss Broks
maintainerPATCH v2 1/2 drm/panel: Add DT bindings for Samsung S6D27A1 display panel
This adds device-tree bindings for the Samsung S6D27A1 RGB DPI display panel.
v1 -> v2:
changed additionalProperties to unevaluatedProperties; added vci-supply and vccio-supply as required;
--- .../display/panel/samsung,s6d27a1.yaml | 98 +++++++++++++++++++ 1 file changed, 98 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml
Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml new file +98 -0
@@ -0,0 +1,98 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/samsung,s6d27a1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S6D27A1 display panel + +description: The S6D27A1 is a 480x800 DPI display panel from Samsung Mobile + Displays (SMD). The panel must obey the rules for a SPI slave device + as specified in spi/spi-controller.yaml + +maintainers: + - Markuss Broks <[email protected]> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: samsung,s6d27a1 + + reg: true + + interrupts: + description: provides an optional ESD (electrostatic discharge) + interrupt that signals abnormalities in the display hardware. + This can also be raised for other reasons like erroneous + configuration. + maxItems: 1 + + reset-gpios: true + + vci-supply: + description: regulator that supplies the VCI analog voltage + usually around 3.0 V + + vccio-supply: + description: regulator that supplies the VCCIO voltage usually + around 1.8 V + + backlight: true + + spi-cpha: true + + spi-cpol: true + + spi-max-frequency: + maximum: 1200000 + + port: true + +required: + - compatible + - reg + - vci-supply + - vccio-supply + - spi-cpha + - spi-cpol + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + compatible = "spi-gpio"; + sck-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + miso-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; + cs-gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; + num-chipselects = <1>; + #address-cells = <1>; + #size-cells = <0>; + panel@0 { + compatible = "samsung,s6d27a1"; + spi-max-frequency = <1200000>; + spi-cpha; + spi-cpol; + reg = <0>; + vci-supply = <&lcd_3v0_reg>; + vccio-supply = <&lcd_1v8_reg>; + reset-gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio>; + interrupts = <5 IRQ_TYPE_EDGE_RISING>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + }; + +...
Signature · 1 line
2.32.0
Re: [PATCH v2 1/2] drm/panel: Add DT bindings for Samsung S6D27A1 display panel
Quoted 8 lines · Markuss Broks
This adds device-tree bindings for the Samsung S6D27A1 RGB DPI display panel.
Signed-off-by Markuss Broks <[email protected]>v1 -> v2:
changed additionalProperties to unevaluatedProperties; added vci-supply and vccio-supply as required;
These bindings look good to me:
Will give DT reviewers some slack before applying the patches.
Yours,
Linus Walleij
Re: [PATCH v2 1/2] drm/panel: Add DT bindings for Samsung S6D27A1 display panel
In reply to Markuss BroksQuoted 5 lines · Markuss Broks
This adds device-tree bindings for the Samsung S6D27A1 RGB DPI display panel.
Signed-off-by Markuss Broks <[email protected]>
Quoted 8 lines
v1 -> v2:
changed additionalProperties to unevaluatedProperties; added vci-supply and vccio-supply as required;--- .../display/panel/samsung,s6d27a1.yaml | 98 +++++++++++++++++++ 1 file changed, 98 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml
Markuss Broks
maintainerPATCH v2 2/2 drm/panel: s6d27a1: Add driver for Samsung S6D27A1 display panel
In reply to Markuss BroksThis adds a driver for Samsung S6D27A1 display controller and panel. This panel is found in the Samsung GT-I8160 mobile phone, and possibly some other mobile phones.
This display needs manufacturer commands to configure it; the commands used in this driver were taken from downstream driver by Gareth Phillips; sadly, there is almost no documentation on what they actually do.
This driver re-uses the DBI infrastructure to communicate with the display.
This driver is heavily based on WideChips WS2401 display controller driver by Linus Walleij and on other panel drivers for reference.
v2 -> v3:
fixed checkpatch warnings - not sure about MAINTAINERS, should I put my name up there?
v3 -> v4:
- add a MAINTAINERS entry;
- drop s6d27a1_command macro; use mipi_dbi_command directly;
- dropped "panel initialized" dev_dbg message;
- add drm_panel_of_backlight call to handle backlight on panel turn on/off;
- reorder drm_mipi_dbi and drm_modes headers:
I think they should be in alphabetic order?
--- MAINTAINERS | 6 + drivers/gpu/drm/panel/Kconfig | 11 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-samsung-s6d27a1.c | 320 ++++++++++++++++++ 4 files changed, 338 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6d27a1.c
MAINTAINERS +6 -0
@@ -5962,6 +5962,12 @@ T: git git://anongit.freedesktop.org/drm/drm-misc F: Documentation/devicetree/bindings/display/panel/samsung,lms397kf04.yaml F: drivers/gpu/drm/panel/panel-samsung-db7430.c +DRM DRIVER FOR SAMSUNG S6D27A1 PANELS +M: Markuss Broks <[email protected]> +S: Maintained +F: Documentation/devicetree/bindings/display/panel/samsung,s6d27a1.yaml +F: driver/gpu/drm/panel/panel-samsung-s6d27a1.c + DRM DRIVER FOR SITRONIX ST7703 PANELS M: Guido Günther <[email protected]> R: Purism Kernel Team <[email protected]>
drivers/gpu/drm/panel/Kconfig +11 -0
@@ -392,6 +392,17 @@ config DRM_PANEL_SAMSUNG_S6D16D0 depends on DRM_MIPI_DSI select VIDEOMODE_HELPERS +config DRM_PANEL_SAMSUNG_S6D27A1 + tristate "Samsung S6D27A1 DPI panel driver" + depends on OF && SPI && GPIOLIB + select DRM_MIPI_DBI + help + Say Y here if you want to enable support for the Samsung + S6D27A1 DPI 480x800 panel. + + This panel can be found in Samsung Galaxy Ace 2 + GT-I8160 mobile phone. + config DRM_PANEL_SAMSUNG_S6E3HA2 tristate "Samsung S6E3HA2 DSI video mode panel" depends on OF
drivers/gpu/drm/panel/Makefile +1 -0
@@ -39,6 +39,7 @@ obj-$(CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20) += panel-samsung-atna33xc20.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_DB7430) += panel-samsung-db7430.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D16D0) += panel-samsung-s6d16d0.o +obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D27A1) += panel-samsung-s6d27a1.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03) += panel-samsung-s6e63j0x03.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63M0) += panel-samsung-s6e63m0.o
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +320 -0
320 lines not on this page · raw message
Signature · 1 line
2.32.0
Hi Markuss,
this is looking really good, the following is just nitty gritty details I could fix while applying, we're mostly waiting for DT review now.
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 126
Quoted 6 lines · Markuss Broks
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +6
-0+/* +* Exit sleep mode and initialize display - some hammering is +* necessary. +*/ +mipi_dbi_command (dbi,MIPI_DCS_EXIT_SLEEP_MODE ); +mipi_dbi_command (dbi,MIPI_DCS_EXIT_SLEEP_MODE );
Check if this hammering is really necessary on s6d27a1, on Widechips this is just a bug, what happens if you put just one of them?
Quoted 1 line
+ msleep(50);
This should be msleep(120) on s6d27a1 (according to board-codina-mcde.c)
Yours,
Linus Walleij
Quoted 9 lines · Markuss Broks
This adds a driver for Samsung S6D27A1 display controller and panel. This panel is found in the Samsung GT-I8160 mobile phone, and possibly some other mobile phones.
This display needs manufacturer commands to configure it; the commands used in this driver were taken from downstream driver by Gareth Phillips; sadly, there is almost no documentation on what they actually do.
Quoted 8 lines
This driver re-uses the DBI infrastructure to communicate with the display.
This driver is heavily based on WideChips WS2401 display controller driver by Linus Walleij and on other panel drivers for reference.
Signed-off-by Markuss Broks <[email protected]>v2 -> v3:
Both v3 patches applied to drm-misc-next and pushed.
Yours,
Linus Walleij
Hi Markuss,
sorry for reacting so late!
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c line 82
Quoted 9 lines · Markuss Broks
drivers/gpu/drm/panel/panel-samsung-s6d27a1.c new file +9
-0+#define s6d27a1_command(ctx, cmd, seq...) \ +({ \ + struct mipi_dbi *dbi = &ctx->dbi; \ + int ret; \ + ret = mipi_dbi_command(dbi, cmd, seq); \ + if (ret) { \ + dev_err(ctx->dev, "failure in writing command %02x\n", cmd); \ + } \ +})
You don't need this wrapper anymore, just call mipi_dbi_command() directly everywhere you use s6d27a1_command().
Because I merged this patch:
https://cgit.freedesktop.org/drm/drm-misc/commit/include/drm/drm_mipi_dbi.h?id=3f5aa5ac0b0f9704f0c60f5fbbbcdc8c043d6eb6
Yours,
Linus Walleij