Skip to contentSkip to conversation

tpm: ibmvtpm: Avoid error message when process gets signal while waiting

PATCH Superseded Stefan Berger 3 participants 3 messages Aug 3, 2021 – Aug 5, 2021

Subsystems (4)

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 tpm: ibmvtpm: Avoid error message when process gets signal while waiting

From: Stefan Berger <[email protected]>

When rngd is run as root then lots of these types of message will appear in the kernel log if the TPM has been configured to provide random bytes:

[ 7406.275163] tpm tpm0: tpm_transmit: tpm_recv: error -4

The issue is caused by the following call that is interrupted while waiting for the TPM's response.

sig = wait_event_interruptible(ibmvtpm->wq,

                               !ibmvtpm->tpm_processing_cmd);

Rather than waiting for the response in the low level driver, have it use the polling loop in tpm_try_transmit() that uses a command's duration to poll until a result has been returned by the TPM, thus ending when the timeout has occurred but not responding to signals and ctrl-c anymore. To stay in this polling loop extend tpm_ibmvtpm_status() to return TPM_STATUS_BUSY for as long as the vTPM is busy. Since the loop requires the TPM's timeouts, get them now using tpm_get_timeouts() after setting the TPM2 version flag on the chip.

Rename the tpm_processing_cmd to tpm_status in ibmvtpm_dev and set the TPM_STATUS_BUSY flag while the vTPM is busy processing a command.

To recreat the resolved issue start rngd like this:

sudo rngd -r /dev/hwrng -t
sudo rngd -r /dev/tpm0 -t

Fixes 6674ff145eef ("tpm_ibmvtpm: properly handle interrupted packet receptions")
Cc Nayna Jain <[email protected]>
Cc George Wilson <[email protected]>

---

v2:
- reworded commit text

---
 drivers/char/tpm/tpm_ibmvtpm.c | 31 ++++++++++++++++++-------------
 drivers/char/tpm/tpm_ibmvtpm.h |  3 ++-
 2 files changed, 20 insertions(+), 14 deletions(-)
drivers/char/tpm/tpm_ibmvtpm.c +18 -13
index 903604769de9..5d795866b483 100644
@@ -106,17 +106,12 @@ static int tpm_ibmvtpm_recv(struct tpm_chip *chip, u8 *buf, size_t count)
 {
 	struct ibmvtpm_dev *ibmvtpm = dev_get_drvdata(&chip->dev);
 	u16 len;
-	int sig;
 
 	if (!ibmvtpm->rtce_buf) {
 		dev_err(ibmvtpm->dev, "ibmvtpm device is not ready\n");
 		return 0;
 	}
 
-	sig = wait_event_interruptible(ibmvtpm->wq, !ibmvtpm->tpm_processing_cmd);
-	if (sig)
-		return -EINTR;
-
 	len = ibmvtpm->res_len;
 
 	if (count < len) {
@@ -220,11 +215,12 @@ static int tpm_ibmvtpm_send(struct tpm_chip *chip, u8 *buf, size_t count)
 		return -EIO;
 	}
 
-	if (ibmvtpm->tpm_processing_cmd) {
+	if ((ibmvtpm->tpm_status & TPM_STATUS_BUSY)) {
 		dev_info(ibmvtpm->dev,
 		         "Need to wait for TPM to finish\n");
 		/* wait for previous command to finish */
-		sig = wait_event_interruptible(ibmvtpm->wq, !ibmvtpm->tpm_processing_cmd);
+		sig = wait_event_interruptible(ibmvtpm->wq,
+				(ibmvtpm->tpm_status & TPM_STATUS_BUSY) == 0);
 		if (sig)
 			return -EINTR;
 	}
@@ -237,7 +233,7 @@ static int tpm_ibmvtpm_send(struct tpm_chip *chip, u8 *buf, size_t count)
 	 * set the processing flag before the Hcall, since we may get the
 	 * result (interrupt) before even being able to check rc.
 	 */
-	ibmvtpm->tpm_processing_cmd = true;
+	ibmvtpm->tpm_status |= TPM_STATUS_BUSY;
 
 again:
 	rc = ibmvtpm_send_crq(ibmvtpm->vdev,
@@ -255,7 +251,7 @@ static int tpm_ibmvtpm_send(struct tpm_chip *chip, u8 *buf, size_t count)
 			goto again;
 		}
 		dev_err(ibmvtpm->dev, "tpm_ibmvtpm_send failed rc=%d\n", rc);
-		ibmvtpm->tpm_processing_cmd = false;
+		ibmvtpm->tpm_status &= ~TPM_STATUS_BUSY;
 	}
 
 	spin_unlock(&ibmvtpm->rtce_lock);
@@ -269,7 +265,9 @@ static void tpm_ibmvtpm_cancel(struct tpm_chip *chip)
 
 static u8 tpm_ibmvtpm_status(struct tpm_chip *chip)
 {
-	return 0;
+	struct ibmvtpm_dev *ibmvtpm = dev_get_drvdata(&chip->dev);
+
+	return ibmvtpm->tpm_status;
 }
 
 /**
@@ -457,7 +455,7 @@ static const struct tpm_class_ops tpm_ibmvtpm = {
 	.send = tpm_ibmvtpm_send,
 	.cancel = tpm_ibmvtpm_cancel,
 	.status = tpm_ibmvtpm_status,
-	.req_complete_mask = 0,
+	.req_complete_mask = TPM_STATUS_BUSY,
 	.req_complete_val = 0,
 	.req_canceled = tpm_ibmvtpm_req_canceled,
 };
@@ -550,7 +548,7 @@ static void ibmvtpm_crq_process(struct ibmvtpm_crq *crq,
 		case VTPM_TPM_COMMAND_RES:
 			/* len of the data in rtce buffer */
 			ibmvtpm->res_len = be16_to_cpu(crq->len);
-			ibmvtpm->tpm_processing_cmd = false;
+			ibmvtpm->tpm_status &= ~TPM_STATUS_BUSY;
 			wake_up_interruptible(&ibmvtpm->wq);
 			return;
 		default:
@@ -688,8 +686,15 @@ static int tpm_ibmvtpm_probe(struct vio_dev *vio_dev,
 		goto init_irq_cleanup;
 	}
 
-	if (!strcmp(id->compat, "IBM,vtpm20")) {
+
+	if (!strcmp(id->compat, "IBM,vtpm20"))
 		chip->flags |= TPM_CHIP_FLAG_TPM2;
+
+	rc = tpm_get_timeouts(chip);
+	if (rc)
+		goto init_irq_cleanup;
+
+	if (chip->flags & TPM_CHIP_FLAG_TPM2) {
 		rc = tpm2_get_cc_attrs_tbl(chip);
 		if (rc)
 			goto init_irq_cleanup;
drivers/char/tpm/tpm_ibmvtpm.h +2 -1
index b92aa7d3e93e..252f1cccdfc5 100644
@@ -41,7 +41,8 @@ struct ibmvtpm_dev {
 	wait_queue_head_t wq;
 	u16 res_len;
 	u32 vtpm_version;
-	bool tpm_processing_cmd;
+	u8 tpm_status;
+#define TPM_STATUS_BUSY		(1 << 0) /* vtpm is processing a command */
 };
 
 #define CRQ_RES_BUF_SIZE	PAGE_SIZE
Signature · 1 line
2.31.1
Tested-by on v2 1/1
#1 lore raw
Quoted 30 lines · Stefan Berger

From: Stefan Berger <[email protected]>

When rngd is run as root then lots of these types of message will appear in the kernel log if the TPM has been configured to provide random bytes:

[ 7406.275163] tpm tpm0: tpm_transmit: tpm_recv: error -4

The issue is caused by the following call that is interrupted while waiting for the TPM's response.

sig = wait_event_interruptible(ibmvtpm->wq,

                                !ibmvtpm->tpm_processing_cmd);

Rather than waiting for the response in the low level driver, have it use the polling loop in tpm_try_transmit() that uses a command's duration to poll until a result has been returned by the TPM, thus ending when the timeout has occurred but not responding to signals and ctrl-c anymore. To stay in this polling loop extend tpm_ibmvtpm_status() to return TPM_STATUS_BUSY for as long as the vTPM is busy. Since the loop requires the TPM's timeouts, get them now using tpm_get_timeouts() after setting the TPM2 version flag on the chip.

Rename the tpm_processing_cmd to tpm_status in ibmvtpm_dev and set the TPM_STATUS_BUSY flag while the vTPM is busy processing a command.

To recreat the resolved issue start rngd like this:

sudo rngd -r /dev/hwrng -t
sudo rngd -r /dev/tpm0 -t

Quoted 7 lines
Fixes 6674ff145eef ("tpm_ibmvtpm: properly handle interrupted packet receptions")
Cc Nayna Jain <[email protected]>
Cc George Wilson <[email protected]>

Tested the patch applying on kernel version 5.14.0-rc3

1. Ran with recreate commands i.e.
rngd -r /dev/hwrng -t
rngd -r /dev/tpm0 -t

2. Ran the above rngd commands along with "stress-ng - dispatching hogs: 32 af-alg, 32 bsearch, 32 context, 32 cpu, 32 crypt, 32 hsearch, 32 longjmp, 32 lsearch, 32 matrix, 32 qsort, 32 str, 32 stream, 32 tsearch, 32 vecmath, 32 wcs" for 2 hours

Thanks!!

Quoted 125 lines

---

v2:
- reworded commit text

---
  drivers/char/tpm/tpm_ibmvtpm.c | 31 ++++++++++++++++++-------------
  drivers/char/tpm/tpm_ibmvtpm.h |  3 ++-
  2 files changed, 20 insertions(+), 14 deletions(-)
drivers/char/tpm/tpm_ibmvtpm.c +18 -13
index 903604769de9..5d795866b483 100644
@@ -106,17 +106,12 @@ static int tpm_ibmvtpm_recv(struct tpm_chip *chip, u8 *buf, size_t count)
  {
  	struct ibmvtpm_dev *ibmvtpm = dev_get_drvdata(&chip->dev);
  	u16 len;
-	int sig;
 
  	if (!ibmvtpm->rtce_buf) {
  		dev_err(ibmvtpm->dev, "ibmvtpm device is not ready\n");
  		return 0;
  	}
 
-	sig = wait_event_interruptible(ibmvtpm->wq, !ibmvtpm->tpm_processing_cmd);
-	if (sig)
-		return -EINTR;
-
  	len = ibmvtpm->res_len;
 
  	if (count < len) {
@@ -220,11 +215,12 @@ static int tpm_ibmvtpm_send(struct tpm_chip *chip, u8 *buf, size_t count)
  		return -EIO;
  	}
 
-	if (ibmvtpm->tpm_processing_cmd) {
+	if ((ibmvtpm->tpm_status & TPM_STATUS_BUSY)) {
  		dev_info(ibmvtpm->dev,
  		         "Need to wait for TPM to finish\n");
  		/* wait for previous command to finish */
-		sig = wait_event_interruptible(ibmvtpm->wq, !ibmvtpm->tpm_processing_cmd);
+		sig = wait_event_interruptible(ibmvtpm->wq,
+				(ibmvtpm->tpm_status & TPM_STATUS_BUSY) == 0);
  		if (sig)
  			return -EINTR;
  	}
@@ -237,7 +233,7 @@ static int tpm_ibmvtpm_send(struct tpm_chip *chip, u8 *buf, size_t count)
  	 * set the processing flag before the Hcall, since we may get the
  	 * result (interrupt) before even being able to check rc.
  	 */
-	ibmvtpm->tpm_processing_cmd = true;
+	ibmvtpm->tpm_status |= TPM_STATUS_BUSY;
 
  again:
  	rc = ibmvtpm_send_crq(ibmvtpm->vdev,
@@ -255,7 +251,7 @@ static int tpm_ibmvtpm_send(struct tpm_chip *chip, u8 *buf, size_t count)
  			goto again;
  		}
  		dev_err(ibmvtpm->dev, "tpm_ibmvtpm_send failed rc=%d\n", rc);
-		ibmvtpm->tpm_processing_cmd = false;
+		ibmvtpm->tpm_status &= ~TPM_STATUS_BUSY;
  	}
 
  	spin_unlock(&ibmvtpm->rtce_lock);
@@ -269,7 +265,9 @@ static void tpm_ibmvtpm_cancel(struct tpm_chip *chip)
 
  static u8 tpm_ibmvtpm_status(struct tpm_chip *chip)
  {
-	return 0;
+	struct ibmvtpm_dev *ibmvtpm = dev_get_drvdata(&chip->dev);
+
+	return ibmvtpm->tpm_status;
  }
 
  /**
@@ -457,7 +455,7 @@ static const struct tpm_class_ops tpm_ibmvtpm = {
  	.send = tpm_ibmvtpm_send,
  	.cancel = tpm_ibmvtpm_cancel,
  	.status = tpm_ibmvtpm_status,
-	.req_complete_mask = 0,
+	.req_complete_mask = TPM_STATUS_BUSY,
  	.req_complete_val = 0,
  	.req_canceled = tpm_ibmvtpm_req_canceled,
  };
@@ -550,7 +548,7 @@ static void ibmvtpm_crq_process(struct ibmvtpm_crq *crq,
  		case VTPM_TPM_COMMAND_RES:
  			/* len of the data in rtce buffer */
  			ibmvtpm->res_len = be16_to_cpu(crq->len);
-			ibmvtpm->tpm_processing_cmd = false;
+			ibmvtpm->tpm_status &= ~TPM_STATUS_BUSY;
  			wake_up_interruptible(&ibmvtpm->wq);
  			return;
  		default:
@@ -688,8 +686,15 @@ static int tpm_ibmvtpm_probe(struct vio_dev *vio_dev,
  		goto init_irq_cleanup;
  	}
 
-	if (!strcmp(id->compat, "IBM,vtpm20")) {
+
+	if (!strcmp(id->compat, "IBM,vtpm20"))
  		chip->flags |= TPM_CHIP_FLAG_TPM2;
+
+	rc = tpm_get_timeouts(chip);
+	if (rc)
+		goto init_irq_cleanup;
+
+	if (chip->flags & TPM_CHIP_FLAG_TPM2) {
  		rc = tpm2_get_cc_attrs_tbl(chip);
  		if (rc)
  			goto init_irq_cleanup;
drivers/char/tpm/tpm_ibmvtpm.h +2 -1
index b92aa7d3e93e..252f1cccdfc5 100644
@@ -41,7 +41,8 @@ struct ibmvtpm_dev {
  	wait_queue_head_t wq;
  	u16 res_len;
  	u32 vtpm_version;
-	bool tpm_processing_cmd;
+	u8 tpm_status;
+#define TPM_STATUS_BUSY		(1 << 0) /* vtpm is processing a command */
  };
 
  #define CRQ_RES_BUF_SIZE	PAGE_SIZE
Signature · 2 lines
Thanks and Regards
R.Nageswara Sastry
maintainer
#2 lore raw
In reply to Stefan Berger
Quoted 165 lines · Stefan Berger

From: Stefan Berger <[email protected]>

When rngd is run as root then lots of these types of message will appear in the kernel log if the TPM has been configured to provide random bytes:

[ 7406.275163] tpm tpm0: tpm_transmit: tpm_recv: error -4

The issue is caused by the following call that is interrupted while waiting for the TPM's response.

sig = wait_event_interruptible(ibmvtpm->wq,

                               !ibmvtpm->tpm_processing_cmd);

Rather than waiting for the response in the low level driver, have it use the polling loop in tpm_try_transmit() that uses a command's duration to poll until a result has been returned by the TPM, thus ending when the timeout has occurred but not responding to signals and ctrl-c anymore. To stay in this polling loop extend tpm_ibmvtpm_status() to return TPM_STATUS_BUSY for as long as the vTPM is busy. Since the loop requires the TPM's timeouts, get them now using tpm_get_timeouts() after setting the TPM2 version flag on the chip.

Rename the tpm_processing_cmd to tpm_status in ibmvtpm_dev and set the TPM_STATUS_BUSY flag while the vTPM is busy processing a command.

To recreat the resolved issue start rngd like this:

sudo rngd -r /dev/hwrng -t
sudo rngd -r /dev/tpm0 -t

Fixes 6674ff145eef ("tpm_ibmvtpm: properly handle interrupted packet receptions")
Cc Nayna Jain <[email protected]>
Cc George Wilson <[email protected]>

---

v2:
- reworded commit text

---
 drivers/char/tpm/tpm_ibmvtpm.c | 31 ++++++++++++++++++-------------
 drivers/char/tpm/tpm_ibmvtpm.h |  3 ++-
 2 files changed, 20 insertions(+), 14 deletions(-)
drivers/char/tpm/tpm_ibmvtpm.c +18 -13
index 903604769de9..5d795866b483 100644
@@ -106,17 +106,12 @@ static int tpm_ibmvtpm_recv(struct tpm_chip *chip, u8 *buf, size_t count)
 {
 	struct ibmvtpm_dev *ibmvtpm = dev_get_drvdata(&chip->dev);
 	u16 len;
-	int sig;
 
 	if (!ibmvtpm->rtce_buf) {
 		dev_err(ibmvtpm->dev, "ibmvtpm device is not ready\n");
 		return 0;
 	}
 
-	sig = wait_event_interruptible(ibmvtpm->wq, !ibmvtpm->tpm_processing_cmd);
-	if (sig)
-		return -EINTR;
-
 	len = ibmvtpm->res_len;
 
 	if (count < len) {
@@ -220,11 +215,12 @@ static int tpm_ibmvtpm_send(struct tpm_chip *chip, u8 *buf, size_t count)
 		return -EIO;
 	}
 
-	if (ibmvtpm->tpm_processing_cmd) {
+	if ((ibmvtpm->tpm_status & TPM_STATUS_BUSY)) {
 		dev_info(ibmvtpm->dev,
 		         "Need to wait for TPM to finish\n");
 		/* wait for previous command to finish */
-		sig = wait_event_interruptible(ibmvtpm->wq, !ibmvtpm->tpm_processing_cmd);
+		sig = wait_event_interruptible(ibmvtpm->wq,
+				(ibmvtpm->tpm_status & TPM_STATUS_BUSY) == 0);
 		if (sig)
 			return -EINTR;
 	}
@@ -237,7 +233,7 @@ static int tpm_ibmvtpm_send(struct tpm_chip *chip, u8 *buf, size_t count)
 	 * set the processing flag before the Hcall, since we may get the
 	 * result (interrupt) before even being able to check rc.
 	 */
-	ibmvtpm->tpm_processing_cmd = true;
+	ibmvtpm->tpm_status |= TPM_STATUS_BUSY;
 
 again:
 	rc = ibmvtpm_send_crq(ibmvtpm->vdev,
@@ -255,7 +251,7 @@ static int tpm_ibmvtpm_send(struct tpm_chip *chip, u8 *buf, size_t count)
 			goto again;
 		}
 		dev_err(ibmvtpm->dev, "tpm_ibmvtpm_send failed rc=%d\n", rc);
-		ibmvtpm->tpm_processing_cmd = false;
+		ibmvtpm->tpm_status &= ~TPM_STATUS_BUSY;
 	}
 
 	spin_unlock(&ibmvtpm->rtce_lock);
@@ -269,7 +265,9 @@ static void tpm_ibmvtpm_cancel(struct tpm_chip *chip)
 
 static u8 tpm_ibmvtpm_status(struct tpm_chip *chip)
 {
-	return 0;
+	struct ibmvtpm_dev *ibmvtpm = dev_get_drvdata(&chip->dev);
+
+	return ibmvtpm->tpm_status;
 }
 
 /**
@@ -457,7 +455,7 @@ static const struct tpm_class_ops tpm_ibmvtpm = {
 	.send = tpm_ibmvtpm_send,
 	.cancel = tpm_ibmvtpm_cancel,
 	.status = tpm_ibmvtpm_status,
-	.req_complete_mask = 0,
+	.req_complete_mask = TPM_STATUS_BUSY,
 	.req_complete_val = 0,
 	.req_canceled = tpm_ibmvtpm_req_canceled,
 };
@@ -550,7 +548,7 @@ static void ibmvtpm_crq_process(struct ibmvtpm_crq *crq,
 		case VTPM_TPM_COMMAND_RES:
 			/* len of the data in rtce buffer */
 			ibmvtpm->res_len = be16_to_cpu(crq->len);
-			ibmvtpm->tpm_processing_cmd = false;
+			ibmvtpm->tpm_status &= ~TPM_STATUS_BUSY;
 			wake_up_interruptible(&ibmvtpm->wq);
 			return;
 		default:
@@ -688,8 +686,15 @@ static int tpm_ibmvtpm_probe(struct vio_dev *vio_dev,
 		goto init_irq_cleanup;
 	}
 
-	if (!strcmp(id->compat, "IBM,vtpm20")) {
+
+	if (!strcmp(id->compat, "IBM,vtpm20"))
 		chip->flags |= TPM_CHIP_FLAG_TPM2;
+
+	rc = tpm_get_timeouts(chip);
+	if (rc)
+		goto init_irq_cleanup;
+
+	if (chip->flags & TPM_CHIP_FLAG_TPM2) {
 		rc = tpm2_get_cc_attrs_tbl(chip);
 		if (rc)
 			goto init_irq_cleanup;
drivers/char/tpm/tpm_ibmvtpm.h +2 -1
index b92aa7d3e93e..252f1cccdfc5 100644
@@ -41,7 +41,8 @@ struct ibmvtpm_dev {
 	wait_queue_head_t wq;
 	u16 res_len;
 	u32 vtpm_version;
-	bool tpm_processing_cmd;
+	u8 tpm_status;
+#define TPM_STATUS_BUSY		(1 << 0) /* vtpm is processing a command */
 };
 
 #define CRQ_RES_BUF_SIZE	PAGE_SIZE
Signature · 1 line
2.31.1

Please do not do the rename in the bug fix. If you really want to rename, then this must be split into two commits.

/Jarkko