video: Add simple driver for ST-Ericsson MCDE with pre-configured display
PATCH 1/1 video: Add simple driver for ST-Ericsson MCDE with pre-configured display
The U-Boot port for ST-Ericsson Ux500 is currently only used on the "stemmy" board, where U-Boot runs after firmware that already sets up a boot splash screen. This means that the display is already on and we can just continue using it for U-Boot.
Add a simple driver that simplifies this by reading the display configuration (e.g. screen size, bpp) from the hardware registers.
It also checks the configured "source synchronization" - for some displays (usually DSI command mode displays) we need to explicitly trigger a software sync. This is done through the video_sync() callback that triggers the sync and wait for completion.
---
drivers/video/Kconfig | 12 +++ drivers/video/Makefile | 1 + drivers/video/mcde_simple.c | 141 ++++++++++++++++++++++++++++++++++++ 3 files changed, 154 insertions(+) create mode 100644 drivers/video/mcde_simple.c
drivers/video/Kconfig +12 -0
@@ -854,6 +854,18 @@ config VIDEO_DT_SIMPLEFB The video output is initialized by U-Boot, and kept by the kernel. +config VIDEO_MCDE_SIMPLE + bool "Simple driver for ST-Ericsson MCDE with preconfigured display" + depends on DM_VIDEO + help + Enables a simple display driver for ST-Ericsson MCDE + (Multichannel Display Engine), which reads the configuration from + the MCDE registers. + + This driver assumes that the display hardware has been initialized + before u-boot starts, and u-boot will simply render to the pre- + allocated frame buffer surface. + config OSD bool "Enable OSD support" depends on DM
drivers/video/Makefile +1 -0
@@ -58,6 +58,7 @@ obj-$(CONFIG_VIDEO_LCD_ORISETECH_OTM8009A) += orisetech_otm8009a.o obj-$(CONFIG_VIDEO_LCD_RAYDIUM_RM68200) += raydium-rm68200.o obj-$(CONFIG_VIDEO_LCD_SSD2828) += ssd2828.o obj-$(CONFIG_VIDEO_LCD_TDO_TL070WSH30) += tdo-tl070wsh30.o +obj-$(CONFIG_VIDEO_MCDE_SIMPLE) += mcde_simple.o obj-${CONFIG_VIDEO_MESON} += meson/ obj-${CONFIG_VIDEO_MIPI_DSI} += mipi_dsi.o obj-$(CONFIG_VIDEO_MVEBU) += mvebu_lcd.o
drivers/video/mcde_simple.c new file +141 -0
141 lines not on this page · raw message
Signature · 1 line
2.32.0
Quoted 8 lines · Stephan Gerhold
The U-Boot port for ST-Ericsson Ux500 is currently only used on the "stemmy" board, where U-Boot runs after firmware that already sets up a boot splash screen. This means that the display is already on and we can just continue using it for U-Boot.
Add a simple driver that simplifies this by reading the display configuration (e.g. screen size, bpp) from the hardware registers.
Quoted 7 lines
It also checks the configured "source synchronization" - for some displays (usually DSI command mode displays) we need to explicitly trigger a software sync. This is done through the
video_sync()callback that triggers the sync and wait for completion.Cc Linus Walleij <[email protected]>Signed-off-by Stephan Gerhold <[email protected]>
Yours,
Linus Walleij
On Fri, 2 Jul 2021 19:21:56 +0200
Stephan Gerhold [email protected] wrote:
...
Quoted 5 lines
drivers/video/Kconfig | 12 +++ drivers/video/Makefile | 1 + drivers/video/mcde_simple.c | 141 ++++++++++++++++++++++++++++++++++++ 3 files changed, 154 insertions(+) create mode 100644 drivers/video/mcde_simple.c
applied to u-boot-video/master, thanks!
--
Anatolij