mtd: spinand: add support for Foresee FS35ND0*G parts
Subsystems (2)
PATCH v3 1/1 mtd: spinand: add support for Foresee FS35ND0*G parts
Add support for the various Foresee FS35ND0*G parts manufactured by Longsys.
---
Changes since v2:
- Originally I only had the 1Gbit version of this chip, now I have the 2Gbit and 4Gbit variations so I've added support for those too. There is no datasheet for the bigger chips but they are documented in a flashing tool from an SoC vendor so I took the parameters from there.
- Previous versions of this patch only had single io read cache variants. My SPI flash driver now supports dual and quad io for reading so I added and tested those modes too. My driver/hardware only supports single io for writing so those are still left out.
- Implemented proper logic for checking the ECC status.
- Combined with the previous patch for 1-filling the OOB in the page buffer before writing I have been using this for a few months now without anything getting broken.
drivers/mtd/nand/spi/Makefile | 2 +- drivers/mtd/nand/spi/core.c | 1 + drivers/mtd/nand/spi/longsys.c | 134 +++++++++++++++++++++++++++++++++ include/linux/mtd/spinand.h | 1 + 4 files changed, 137 insertions(+), 1 deletion(-) create mode 100644 drivers/mtd/nand/spi/longsys.c
drivers/mtd/nand/spi/Makefile +1 -1
@@ -1,3 +1,3 @@ # SPDX-License-Identifier: GPL-2.0 -spinand-objs := core.o gigadevice.o macronix.o micron.o paragon.o toshiba.o winbond.o +spinand-objs := core.o gigadevice.o longsys.o macronix.o micron.o paragon.o toshiba.o winbond.o obj-$(CONFIG_MTD_SPI_NAND) += spinand.o
drivers/mtd/nand/spi/core.c +1 -0
@@ -895,6 +895,7 @@ static const struct nand_ops spinand_ops = {static const struct spinand_manufacturer *spinand_manufacturers[] = { &gigadevice_spinand_manufacturer, + &longsys_spinand_manufacturer, ¯onix_spinand_manufacturer, µn_spinand_manufacturer, ¶gon_spinand_manufacturer,
drivers/mtd/nand/spi/longsys.c new file +134 -0
134 lines not on this page · raw message
include/linux/mtd/spinand.h +1 -0
@@ -261,6 +261,7 @@ struct spinand_manufacturer {/* SPI NAND manufacturers */ extern const struct spinand_manufacturer gigadevice_spinand_manufacturer; +extern const struct spinand_manufacturer longsys_spinand_manufacturer;extern const struct spinand_manufacturer macronix_spinand_manufacturer;extern const struct spinand_manufacturer micron_spinand_manufacturer;extern const struct spinand_manufacturer paragon_spinand_manufacturer;
Signature · 1 line
2.32.0
Miquel Raynal
maintainerHi Daniel,
Daniel Palmer <[email protected]> wrote on Wed, 11 Aug 2021 17:49:24 +0900:
Quoted 79 lines
Add support for the various Foresee FS35ND0*G parts manufactured by Longsys.
Signed-off-by Daniel Palmer <[email protected]>---
Changes since v2:
- Originally I only had the 1Gbit version of this chip, now I have the 2Gbit and 4Gbit variations so I've added support for those too. There is no datasheet for the bigger chips but they are documented in a flashing tool from an SoC vendor so I took the parameters from there.
- Previous versions of this patch only had single io read cache variants. My SPI flash driver now supports dual and quad io for reading so I added and tested those modes too. My driver/hardware only supports single io for writing so those are still left out.
- Implemented proper logic for checking the ECC status.
- Combined with the previous patch for 1-filling the OOB in the page buffer before writing I have been using this for a few months now without anything getting broken.drivers/mtd/nand/spi/Makefile | 2 +- drivers/mtd/nand/spi/core.c | 1 + drivers/mtd/nand/spi/longsys.c | 134 +++++++++++++++++++++++++++++++++ include/linux/mtd/spinand.h | 1 + 4 files changed, 137 insertions(+), 1 deletion(-) create mode 100644 drivers/mtd/nand/spi/longsys.cdrivers/mtd/nand/spi/Makefile +1
-1@@ -1,3 +1,3 @@ # SPDX-License-Identifier: GPL-2.0 -spinand-objs := core.o gigadevice.o macronix.o micron.o paragon.o toshiba.o winbond.o +spinand-objs := core.o gigadevice.o longsys.o macronix.o micron.o paragon.o toshiba.o winbond.o obj-$(CONFIG_MTD_SPI_NAND) += spinand.odrivers/mtd/nand/spi/core.c +1
-0@@ -895,6 +895,7 @@ static const struct nand_ops spinand_ops = {static const struct spinand_manufacturer *spinand_manufacturers[] = { &gigadevice_spinand_manufacturer, + &longsys_spinand_manufacturer, ¯onix_spinand_manufacturer, µn_spinand_manufacturer, ¶gon_spinand_manufacturer,drivers/mtd/nand/spi/longsys.c new file +27
-0@@ -0,0 +1,134 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Copyright (c) 2020 Daniel Palmer <[email protected]> +* +*/ + +#include <linux/device.h> +#include <linux/kernel.h> +#include <linux/mtd/spinand.h> + +#define SPINAND_MFR_LONGSYS 0xCD +#define FS35ND01G_S1Y2_STATUS_ECC_0_3_BITFLIPS (0 << 4) +#define FS35ND01G_S1Y2_STATUS_ECC_4_BITFLIPS (1 << 4) +#define FS35ND01G_S1Y2_STATUS_ECC_UNCORRECTABLE (2 << 4) + +static SPINAND_OP_VARIANTS(read_cache_variants, + SPINAND_PAGE_READ_FROM_CACHE_QUADIO_OP(0, 2, NULL, 0), +SPINAND_PAGE_READ_FROM_CACHE_X4_OP (0 ,1 ,NULL ,0 ), +SPINAND_PAGE_READ_FROM_CACHE_DUALIO_OP (0 ,1 ,NULL ,0 ), +SPINAND_PAGE_READ_FROM_CACHE_X2_OP (0 ,1 ,NULL ,0 ), + SPINAND_PAGE_READ_FROM_CACHE_OP(false, 0, 1, NULL, 0)); + +static SPINAND_OP_VARIANTS(write_cache_variants, + SPINAND_PROG_LOAD(true, 0, NULL, 0)); + +static SPINAND_OP_VARIANTS(update_cache_variants, + SPINAND_PROG_LOAD(false, 0, NULL, 0));
drivers/mtd/nand/spi/longsys.c line 37
Quoted 10 lines
drivers/mtd/nand/spi/longsys.c new file +10
-0+ +static int fs35nd01g_s1y2_ooblayout_ecc (struct mtd_info *mtd,int section, +struct mtd_oob_region *region) +{ +if (section >3 ) +return -ERANGE ; + +/* ECC is not user accessible */ + region->offset =0 ; + region->length =0 ;
Can't you just return -ERANGE directly? (maybe not).
If you can't then just return -ERANGE on if (section), no need for two additional calls.
Quoted 11 lines
drivers/mtd/nand/spi/longsys.c new file +11
-0+ +return 0 ; +} + +static int fs35nd01g_s1y2_ooblayout_free (struct mtd_info *mtd,int section, +struct mtd_oob_region *region) +{ +if (section >3 ) +return -ERANGE ; + +/*
drivers/mtd/nand/spi/longsys.c line 58
Quoted 10 lines
drivers/mtd/nand/spi/longsys.c new file +10
-0+* No ECC data is stored in the accessible OOB so the full 16 bytes +* of each spare region is available to the user. Apparently also +* covered by the internal ECC. +*/ +if (section) { + region->offset =16 * section; + region->length =16 ; + }else { +/* First byte in spare0 area is used for bad block marker */ + region->offset =1 ;
So far we reserved two bytes for BBM while we know for now we only use one.
drivers/mtd/nand/spi/longsys.c line 60
Quoted 2 lines
drivers/mtd/nand/spi/longsys.c new file +2
-0+ region->length =15 ; + }
You can just return
if (section) return -ERANGE; offset = 2; length = (4 * 16) - offset; return 0;
Quoted 12 lines
drivers/mtd/nand/spi/longsys.c new file +12
-0+ +return 0 ; +} + +static const struct mtd_ooblayout_ops fs35nd01g_s1y2_ooblayout = { + .ecc = fs35nd01g_s1y2_ooblayout_ecc, + .free = fs35nd01g_s1y2_ooblayout_free, +}; + +static int fs35nd01g_s1y2_ecc_get_status (struct spinand_device *spinand, +u8 status) +{
drivers/mtd/nand/spi/longsys.c line 82
Quoted 10 lines
drivers/mtd/nand/spi/longsys.c new file +10
-0+switch (status &STATUS_ECC_MASK ) { +case FS35ND01G_S1Y2_STATUS_ECC_0_3_BITFLIPS : +return 3 ; +/* +* The datasheet says *successful* with 4 bits flipped. +* nandbiterrs always complains that the read reported +* successful but the data is incorrect. +*/ +case FS35ND01G_S1Y2_STATUS_ECC_4_BITFLIPS : +return 4 ;
This is a real issue. Can you use the nandflipbits tool from the mtd-utils package (you should take a recent version of the package) and try to observe what happens when you insert a 4th bitflip in a section?
I generally believe the tool more than the datasheet :)
Quoted 57 lines
drivers/mtd/nand/spi/longsys.c new file +52
-0+case FS35ND01G_S1Y2_STATUS_ECC_UNCORRECTABLE : +return -EBADMSG ; +default : +break ; + } + +return -EINVAL ; +} + +static const struct spinand_info longsys_spinand_table[] = { +SPINAND_INFO ("FS35ND01G-S1Y2" , +SPINAND_ID (SPINAND_READID_METHOD_OPCODE_DUMMY ,0xEA ,0x11 ), +NAND_MEMORG (1 ,2048 ,64 ,64 ,1024 ,20 ,1 ,1 ,1 ), +NAND_ECCREQ (4 ,512 ), +SPINAND_INFO_OP_VARIANTS (&read_cache_variants, + &write_cache_variants, + &update_cache_variants), +SPINAND_HAS_QE_BIT , +SPINAND_ECCINFO (&fs35nd01g_s1y2_ooblayout, + fs35nd01g_s1y2_ecc_get_status)), +SPINAND_INFO ("FS35ND02G-S3Y2" , +SPINAND_ID (SPINAND_READID_METHOD_OPCODE_DUMMY ,0xEB ,0x11 ), +NAND_MEMORG (1 ,2048 ,64 ,64 ,2048 ,40 ,1 ,1 ,1 ), +NAND_ECCREQ (4 ,512 ), +SPINAND_INFO_OP_VARIANTS (&read_cache_variants, + &write_cache_variants, + &update_cache_variants), +SPINAND_HAS_QE_BIT , +SPINAND_ECCINFO (&fs35nd01g_s1y2_ooblayout, + fs35nd01g_s1y2_ecc_get_status)), +SPINAND_INFO ("FS35ND04G-S2Y2" , +SPINAND_ID (SPINAND_READID_METHOD_OPCODE_DUMMY ,0xEC ,0x11 ), +NAND_MEMORG (1 ,2048 ,64 ,64 ,4096 ,40 ,1 ,1 ,1 ), +NAND_ECCREQ (4 ,512 ), +SPINAND_INFO_OP_VARIANTS (&read_cache_variants, + &write_cache_variants, + &update_cache_variants), +SPINAND_HAS_QE_BIT , +SPINAND_ECCINFO (&fs35nd01g_s1y2_ooblayout, + fs35nd01g_s1y2_ecc_get_status)), +}; + +static const struct spinand_manufacturer_ops longsys_spinand_manuf_ops = { +}; + +const struct spinand_manufacturer longsys_spinand_manufacturer = { + .id =SPINAND_MFR_LONGSYS , + .name ="Longsys" , + .chips = longsys_spinand_table, + .nchips =ARRAY_SIZE (longsys_spinand_table), + .ops = &longsys_spinand_manuf_ops, +};include/linux/mtd/spinand.h +0
-0
include/linux/mtd/spinand.h struct spinand_manufacturer { · line 267
Quoted 7 lines
include/linux/mtd/spinand.h +1
-0@@ -261,6 +261,7 @@ struct spinand_manufacturer {/* SPI NAND manufacturers */ extern const struct spinand_manufacturer gigadevice_spinand_manufacturer; +extern const struct spinand_manufacturer longsys_spinand_manufacturer;extern const struct spinand_manufacturer macronix_spinand_manufacturer;extern const struct spinand_manufacturer micron_spinand_manufacturer;extern const struct spinand_manufacturer paragon_spinand_manufacturer;
Otherwise LGTM.
Thanks,
Miquèl
Hi Miquel,
Quoted 8 lines
drivers/mtd/nand/spi/longsys.c line 82
Quoted 7 lines
drivers/mtd/nand/spi/longsys.c new file +7
-0+/* +* The datasheet says *successful* with 4 bits flipped. +* nandbiterrs always complains that the read reported +* successful but the data is incorrect. +*/ +case FS35ND01G_S1Y2_STATUS_ECC_4_BITFLIPS : +return 4 ;
Quoted 5 lines
This is a real issue. Can you use the nandflipbits tool from the mtd-utils package (you should take a recent version of the package) and try to observe what happens when you insert a 4th bitflip in a section?
I generally believe the tool more than the datasheet :)
Maybe I'm using it incorrectly but I can't get a 4 bit flipped situation to happen.
I erased the paged so it's all 0xFF:
# flash_erase /dev/mtd0 0x8000000 1 Erasing 128 Kibyte @ 8000000 -- 100 % complete # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 ECC failed: 0 ECC corrected: 6234 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
Then used nandflipbits to flip a bunch of bits in the first byte and then a few other bytes:
# nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 ECC failed: 0 ECC corrected: 6246 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: f0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: eb ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ef ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ef ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
Anyhow,
I think we should probably return -EBADMSG if the 4 bit flips status appears as nandbiterrs always complains that the data is wrong.
Cheers,
Daniel
Miquel Raynal
maintainerHi Daniel,
Daniel Palmer <[email protected]> wrote on Mon, 23 Aug 2021 23:19:02 +0900:
Quoted 58 lines
Hi Miquel,
Quoted 8 lines
drivers/mtd/nand/spi/longsys.c line 82
Quoted 7 lines
drivers/mtd/nand/spi/longsys.c new file +7
-0+/* +* The datasheet says *successful* with 4 bits flipped. +* nandbiterrs always complains that the read reported +* successful but the data is incorrect. +*/ +case FS35ND01G_S1Y2_STATUS_ECC_4_BITFLIPS : +return 4 ;Quoted 5 lines
This is a real issue. Can you use the nandflipbits tool from the mtd-utils package (you should take a recent version of the package) and try to observe what happens when you insert a 4th bitflip in a section?
I generally believe the tool more than the datasheet :)
Maybe I'm using it incorrectly but I can't get a 4 bit flipped situation to happen.
I erased the paged so it's all
0xFF:# flash_erase /dev/mtd0 0x8000000 1 Erasing 128 Kibyte @ 8000000 -- 100 % complete # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 ECC failed: 0 ECC corrected: 6234 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|Then used nandflipbits to flip a bunch of bits in the first byte and then a few other bytes:
# nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 ECC failed: 0 ECC corrected: 6246 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: f0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: eb ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ef ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ef ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
Quoted 3 lines
Anyhow,
I think we should probably return-EBADMSGif the 4 bit flips status appears as nandbiterrs always complains that the data is wrong.
I am not sure to follow, above the software says "3 corrected bf" while I thought the problem was when getting 4 bf, but the dump show many more. Can you show me how it behaves:
* erase (like you did)
* insert {1, 2, 3, 4, 5} bf and show the dump each time?
Thanks,
Miquèl
Hi Miquel,
Quoted 1 line · Miquel Raynal
I am not sure to follow, above the software says "3 corrected bf" while
Due to the status being "between 0 and 3 bitflips" I think it'll basically report 3 most of the time.
As a refresher we seem to have a status for 0 - 3 flips but ok, 4 bit flips but ok, and >4 flips no go.
In most cases (0 - 3) the driver is reporting 3.
Quoted 4 lines
I thought the problem was when getting 4 bf, but the dump show many more. Can you show me how it behaves:
* erase (like you did)
* insert {1, 2, 3, 4, 5} bf and show the dump each time?
Here's a complete log of erasing the page then flipping all the bits in the first byte.
# flash_erase /dev/mtd0 0x8000000 1 Erasing 128 Kibyte @ 8000000 -- 100 % complete # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 0 ECC corrected: 6249 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| # nandflipbits /dev/mtd0 0@0x8000000 # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 0 ECC corrected: 6252 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: fe ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| # nandflipbits /dev/mtd0 1@0x8000000 # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 0 ECC corrected: 6255 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: fc ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| # nandflipbits /dev/mtd0 2@0x8000000 # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 0 ECC corrected: 6258 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: f8 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| # nandflipbits /dev/mtd0 3@0x8000000 # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 0 ECC corrected: 6261 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: f0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| # nandflipbits /dev/mtd0 4@0x8000000 # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 0 ECC corrected: 6264 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: e0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| # nandflipbits /dev/mtd0 5@0x8000000 # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 0 ECC corrected: 6267 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: c0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| # nandflipbits /dev/mtd0 6@0x8000000 # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 0 ECC corrected: 6270 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: 80 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| # nandflipbits /dev/mtd0 7@0x8000000 # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 0 ECC corrected: 6273 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| #
For completeness logs of what nandbiterrs does:
# flash_erase /dev/mtd0 0x8000000 1
Erasing 128 Kibyte @ 8000000 -- 100 % complete
# nandbiterrs -i ^C 1024 /dev/mtd0
# nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10
ECC failed: 0
ECC corrected: 6478
Number of bad blocks: 0
Number of bbt blocks: 0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x08000000 and ending at 0x08000001...
ECC: 3 corrected bitflip(s) at offset 0x08000000
0x08000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
# nandbiterrs -i -b 1024 /dev/mtd0
incremental biterrors test
Read reported 3 corrected bit errors
Successfully corrected 0 bit errors per subpage
Inserted biterror @ 0/5
Read reported 4 corrected bit errors
ECC failure, invalid data despite read success
# nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10
ECC failed: 0
ECC corrected: 6488
Number of bad blocks: 0
Number of bbt blocks: 0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x08000000 and ending at 0x08000001...
ECC: 4 corrected bitflip(s) at offset 0x08000000
0x08000000: 05 a5 65 e5 05 85 45 c5 b5 35 f5 75 95 15 d5 55 |..e...E..5.u...U|
0x08000010: 6d ed 2d ad 4d cd 0d 8d fd 7d bd 3d dd 5d 9d 1d |m.-.M....}.=.]..|
0x08000020: 81 01 c1 41 a1 21 e1 61 11 91 51 d1 31 b1 71 f1 |...A.!.a..Q.1.q.|
0x08000030: c9 49 89 09 e9 69 a9 29 59 d9 19 99 79 f9 39 b9 |.I...i.)Y...y.9.|
0x08000040: 77 d7 37 b7 57 d7 17 97 e7 67 a7 27 c7 47 87 07 |w.7.W....g.'.G..|
0x08000050: 3f bf 7f ff 1f 9f 5f df af 2f ef 6f 8f 0f cf 4f |?....._../.o...O|
0x08000060: d3 53 93 13 f3 73 b3 33 43 c3 03 83 63 e3 23 a3 |.S...s.3C...c.#.|
0x08000070: 9b 1b db 5b bb 3b fb 7b 0b 8b 4b cb 2b ab 6b eb |...[.;.{..K.+.k.|
0x08000080: 0c 8c 4c cc 2c ac 6c ec 9c 1c dc 5c bc 3c fc 7c |..L.,.l....\.<.||
0x08000090: 44 c4 04 84 64 e4 24 a4 d4 54 94 14 f4 74 b4 34 |D...d.$..T...t.4|
## flash_erase /dev/mtd0 0x8000000 1 Erasing 128 Kibyte @ 8000000 -- 100 % complete # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 0 ECC corrected: 6492 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| # nandbiterrs -o -b 1024 /dev/mtd0 overwrite biterrors test Read reported 3 corrected bit errors Read reported 4 corrected bit errors Failed to recover 1 bitflips Bit error histogram (873 operations total): Page reads with 0 corrected bit errors: 0 Page reads with 1 corrected bit errors: 0 Page reads with 2 corrected bit errors: 0 Page reads with 3 corrected bit errors: 785 # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 1 ECC corrected: 9202 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
Cheers,
Daniel
Miquel Raynal
maintainerHi Daniel,
Daniel Palmer <[email protected]> wrote on Mon, 23 Aug 2021 23:54:20 +0900:
Quoted 41 lines
Hi Miquel,
Quoted 1 line · Miquel Raynal
I am not sure to follow, above the software says "3 corrected bf" while
Due to the status being "between 0 and 3 bitflips" I think it'll basically report 3 most of the time.
As a refresher we seem to have a status for 0 - 3 flips but ok, 4 bit flips but ok, and >4 flips no go.
In most cases (0 - 3) the driver is reporting 3.Quoted 4 lines
I thought the problem was when getting 4 bf, but the dump show many more. Can you show me how it behaves:
* erase (like you did)
* insert {1, 2, 3, 4, 5} bf and show the dump each time?Here's a complete log of erasing the page then flipping all the bits in the first byte.
# flash_erase /dev/mtd0 0x8000000 1 Erasing 128 Kibyte @ 8000000 -- 100 % complete # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10 ECC failed: 0 ECC corrected: 6249 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| # nandflipbits /dev/mtd0 0@0x8000000 # nanddump --bb=dumpbad -s 0x8000000 -l 1 -c -p /dev/mtd0 | head -n 10
Quoted 8 lines
ECC failed: 0 ECC corrected: 6252 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x08000000 and ending at 0x08000001... ECC: 3 corrected bitflip(s) at offset 0x08000000 0x08000000: fe ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
How is this result possible? You are dumping with the ECC engine enabled, it reports 3 bf (meaning that it is actually running, at least the software really thinks there is an on-die engine enabled) but the data has not been corrected. I expect the first byte to be 0xFF after correction. Only with -n (raw dump) we should see this.
Quoted 9 lines
0x08000010: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000020: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000030: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000040: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000050: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000060: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000070: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| 0x08000090: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
Thanks,
Miquèl
Hi Miquel,
Thank you for your patience on this..
Quoted 8 lines · Miquel Raynal
Quoted 2 lines
ECC: 3 corrected bitflip(s) at offset
0x080000000x08000000: fe ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|How is this result possible? You are dumping with the ECC engine enabled, it reports 3 bf (meaning that it is actually running, at least the software really thinks there is an on-die engine enabled) but the data has not been corrected. I expect the first byte to be
0xFFafter correction. Only with -n (raw dump) we should see this.
I did a bit of searching to see if a newer/more detailed datasheet has come about and found some vendor code I hadn't seen before:
This says the ECC enable bit is non-standard and in a register that isn't documented at all in the datasheet.
I guess the spi nand core isn't able to actually control the ECC on these chips at the moment and flipping the bits is updating the ECC too.
Or the ECC isn't enabled at all.
I couldn't see an easy way of overriding which register gets updated so I haven't tried it yet.
Cheers,
Daniel