arm64: dts: broadcom: bcm4908: Add PCIe controllers
PATCH 1/1 arm64: dts: broadcom: bcm4908: Add PCIe controllers
From: Rafał Miłecki <[email protected]>
BCM4908 SoC has 3 PCIe controllers. Describe them.
Signed-off-by Rafał Miłecki <[email protected]>
---
This is WIP. It's enough to initialize PCIe controllers and detect attached devices. Checking DTS files however results in complains about missing "dma-ranges", interrupt mapping & "msi-controller".
--- .../boot/dts/broadcom/bcm4908/bcm4908.dtsi | 53 ++++++++++++++++++- 1 file changed, 52 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi +52 -1
@@ -267,6 +267,57 @@ pmb: power-controller@2800c0 { }; }; + pcie@80040000 { + compatible = "brcm,bcm4908-pcie"; + reg = <0x0 0x80040000 0x0 0xa000>; + power-domains = <&pmb BCM_PMB_PCIE0>; + resets = <&pcie_reset 0>; + reset-names = "perst"; + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pcie"; + device_type = "pci"; + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + // BUS_ADDRESS(3) CPU_PHYSICAL(2) SIZE(2) + ranges = <0x02000000 0x0 0xc0000000 0x0 0xc0000000 0x0 0x10000000>; + }; + + pcie@80050000 { + compatible = "brcm,bcm4908-pcie"; + reg = <0x0 0x80050000 0x0 0xa000>; + power-domains = <&pmb BCM_PMB_PCIE1>; + resets = <&pcie_reset 1>; + reset-names = "perst"; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pcie"; + device_type = "pci"; + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + // BUS_ADDRESS(3) CPU_PHYSICAL(2) SIZE(2) + ranges = <0x02000000 0x0 0xd0000000 0x0 0xd0000000 0x0 0x10000000>; + }; + + pcie@80060000 { + compatible = "brcm,bcm4908-pcie"; + reg = <0x0 0x80060000 0x0 0xa000>; + power-domains = <&pmb BCM_PMB_PCIE2>; + resets = <&pcie_reset 2>; + reset-names = "perst"; + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pcie"; + device_type = "pci"; + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + // BUS_ADDRESS(3) CPU_PHYSICAL(2) SIZE(2) + ranges = <0x02000000 0x0 0xe0000000 0x0 0xe0000000 0x0 0x10000000>; + }; + bus@ff800000 { compatible = "simple-bus"; #address-cells = <1>;
@@ -320,7 +371,7 @@ misc@2600 { #size-cells = <1>; ranges = <0x00 0x2600 0xe4>; - reset-controller@2644 { + pcie_reset: reset-controller@2644 { compatible = "brcm,bcm4908-misc-pcie-reset"; reg = <0x44 0x04>; #reset-cells = <1>;
Signature · 1 line
2.26.2