Skip to contentSkip to conversation

board: toradex: verdin-imx8mm: target refresh

PATCH Superseded Marcel Ziswiler 2 participants 12 messages Aug 25, 2021 – Aug 26, 2021

Subsystems (3)

v3 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v3 cover board: toradex: verdin-imx8mm: target refresh

From: Marcel Ziswiler <[email protected]>

An assortment of fixes and improvements like an Ethernet PHY configuration fix, DEK blob encapsulation preparation, migration to using binman to pack images, SLEEP_MOCI# enablement, dropping of V1.0 hardware support [1], renaming kernel image variable, using preboot for fdtfile evaluation and watchdog pinctrl fix.

Note that this series is applied on top of Peng's Makefile fix [2] as otherwise, it may not quite generate all binman artefacts in the right order as discussed here [3].

[1] https://developer.toradex.com/verdin-sample-phase-over
[2] https://marc.info/?l=u-boot&m=162908373904742
[3] https://marc.info/?l=u-boot&m=162945614207220

Changes in v3:
- Case fold hex string.
- Revert binman part of imx8mm-verdin-u-boot.dtsi to a plain copy from imx8mm-evk and postpone further improvements to after migrating to a common binman config as agreed with Frieder and Simon.
- New patch cleaning up include order.
- Add Fabio's reviewed-by tag.
- Fix patch.
- Add missing apalis-imx8 part.
- While at it update copyright year resp. period.
- Fix closing endif comment.

Changes in v2:
- Explicitly pass filename to binman when generating binaries as suggested by Heiko.
- Use proper intermediate binary u-boot-spl-ddr.bin for imximage as pointed out by Heiko.
- Drop first patch ("imx: mkimage_fit_atf: fix legacy image generation") as a similar fix was already refused earlier.
- New patch allows booting recent embedded Linux BSPs.
- New patch addressing dynamic fdtfile definition.
- New patch fixing watchdog pinctrl issue.

Igor Opaniuk (1):
verdin-imx8mm: use preboot for fdtfile evaluation

Marcel Ziswiler (6):
imx8m: clean-up kconfig indentation
verdin-imx8mm: fix ethernet
ARM: dts: imx8mm-verdin: prepare for dek blob encapsulation
verdin-imx8mm: switch to use binman to pack images
verdin-imx8mm: clean-up include order
verdin-imx8mm: fix watchdog pinctrl issue

Max Krummenacher (2):
verdin-imx8mm: enable sleep_moci output
verdin-imx8mm: drop support for v1.0 hardware

Oleksandr Suvorov (1):
include/configs: apalis-imx8/verdin-imx8mm: rename kernel image
variable

 arch/arm/dts/imx8mm-verdin-u-boot.dtsi      | 135 +++++++++++++++++++-
 arch/arm/dts/imx8mm-verdin.dts              |  20 ++-
 arch/arm/mach-imx/imx8m/Kconfig             |  21 +--
 board/toradex/verdin-imx8mm/imximage.cfg    |  11 +-
 board/toradex/verdin-imx8mm/verdin-imx8mm.c |  81 +-----------
 configs/verdin-imx8mm_defconfig             |   6 +-
 doc/board/toradex/verdin-imx8mm.rst         |  53 ++++----
 include/configs/apalis-imx8.h               |   6 +-
 include/configs/verdin-imx8mm.h             |  11 +-
 9 files changed, 215 insertions(+), 129 deletions(-)
Signature · 1 line
2.26.2
#1 lore raw

PATCH v3 1/10 imx8m: clean-up kconfig indentation

From: Marcel Ziswiler <[email protected]>

Replace spurious spaces with proper tabs.

---

(no changes since v1)

 arch/arm/mach-imx/imx8m/Kconfig | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)
arch/arm/mach-imx/imx8m/Kconfig +10 -10
index 1d08a2977f5..a2ba30cf332 100644
@@ -25,14 +25,14 @@ config SYS_SOC
 	default "imx8m"
 
 choice
-	prompt  "NXP i.MX8M board select"
+	prompt "NXP i.MX8M board select"
 	optional
 
 config TARGET_IMX8MQ_CM
-        bool "Ronetix iMX8MQ-CM SoM"
+	bool "Ronetix iMX8MQ-CM SoM"
 		select BINMAN
-        select IMX8MQ
-        select IMX8M_LPDDR4
+	select IMX8MQ
+	select IMX8M_LPDDR4
 
 config TARGET_IMX8MQ_EVK
 	bool "imx8mq_evk"
@@ -105,10 +105,10 @@ config TARGET_PICO_IMX8MQ
 	select IMX8M_LPDDR4
 
 config TARGET_VERDIN_IMX8MM
-       bool "Support Toradex Verdin iMX8M Mini module"
-       select IMX8MM
-       select SUPPORT_SPL
-       select IMX8M_LPDDR4
+	bool "Support Toradex Verdin iMX8M Mini module"
+	select IMX8MM
+	select SUPPORT_SPL
+	select IMX8M_LPDDR4
 
 config TARGET_IMX8MM_BEACON
 	bool "imx8mm Beacon Embedded devkit"
@@ -125,14 +125,14 @@ config TARGET_IMX8MN_BEACON
 config TARGET_PHYCORE_IMX8MM
 	bool "PHYTEC PHYCORE i.MX8MM"
 	select IMX8MM
-        select SUPPORT_SPL
+	select SUPPORT_SPL
 	select IMX8M_LPDDR4
 
 config TARGET_PHYCORE_IMX8MP
 	bool "PHYTEC PHYCORE i.MX8MP"
 	select BINMAN
 	select IMX8MP
-        select SUPPORT_SPL
+	select SUPPORT_SPL
 	select IMX8M_LPDDR4
 
 config TARGET_IMX8MM_CL_IOT_GATE
Signature · 1 line
2.26.2
#2 lore raw

PATCH v3 2/10 verdin-imx8mm: fix ethernet

In reply to Marcel Ziswiler

From: Marcel Ziswiler <[email protected]>

Turns out Microship (formerly Micrel) meanwhile integrated proper support for the DLL setup on their KSZ9131. Unfortunately, this conflicts with our previous board code doing that.
Fix this by getting rid of our board code and just relying on the generic implementation relying on rgmii-id being used as phy-mode.

Fixes commit c6df0e2ffdc4

("net: phy: micrel: add support for DLL setup on ksz9131")

---

(no changes since v1)

 arch/arm/dts/imx8mm-verdin.dts              |  2 +-
 board/toradex/verdin-imx8mm/verdin-imx8mm.c | 64 ---------------------
 2 files changed, 1 insertion(+), 65 deletions(-)
arch/arm/dts/imx8mm-verdin.dts +1 -1
index fb0756d6e19..ac2a4b69d3c 100644
@@ -160,7 +160,7 @@
 &fec1 {
 	fsl,magic-packet;
 	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&reg_ethphy>;
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&pinctrl_fec1>;
board/toradex/verdin-imx8mm/verdin-imx8mm.c +0 -64

70 lines not on this page · raw message

Signature · 1 line
2.26.2
#3 lore raw

PATCH v3 3/10 ARM: dts: imx8mm-verdin: prepare for dek blob encapsulation

In reply to Marcel Ziswiler

From: Marcel Ziswiler <[email protected]>

Prepare for DEK blob encapsulation support through "dek_blob" command. On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application call. U-boot sends and receives the DEK and the DEK blob binaries through OP-TEE dynamic shared memory.

To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y

Taken from NXP's commit 56d2050f4028 ("imx8m: Add DEK blob encapsulation for imx8m").

---

(no changes since v1)

 arch/arm/dts/imx8mm-verdin-u-boot.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)
arch/arm/dts/imx8mm-verdin-u-boot.dtsi +7 -0
index 67c31c49b6c..a97626fa0c1 100644
@@ -6,6 +6,13 @@
 #include "imx8mm-u-boot.dtsi"
 
 / {
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
 	wdt-reboot {
 		compatible = "wdt-reboot";
 		wdt = <&wdog1>;
Signature · 1 line
2.26.2
#4 lore raw

PATCH v3 4/10 verdin-imx8mm: switch to use binman to pack images

In reply to Marcel Ziswiler

From: Marcel Ziswiler <[email protected]>

Use binman to pack images.

---

Changes in v3:
- Case fold hex string.
- Revert binman part of imx8mm-verdin-u-boot.dtsi to a plain copy from imx8mm-evk and postpone further improvements to after migrating to a common binman config as agreed with Frieder and Simon.

Changes in v2:
- Explicitly pass filename to binman when generating binaries as suggested by Heiko.
- Use proper intermediate binary u-boot-spl-ddr.bin for imximage as pointed out by Heiko.

 arch/arm/dts/imx8mm-verdin-u-boot.dtsi   | 124 ++++++++++++++++++++++-
 arch/arm/mach-imx/imx8m/Kconfig          |   1 +
 board/toradex/verdin-imx8mm/imximage.cfg |  11 +-
 configs/verdin-imx8mm_defconfig          |   2 +-
 doc/board/toradex/verdin-imx8mm.rst      |  53 +++++-----
 5 files changed, 157 insertions(+), 34 deletions(-)
arch/arm/dts/imx8mm-verdin-u-boot.dtsi +123 -1
index a97626fa0c1..0e041865021 100644
@@ -1,11 +1,15 @@
 // SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
- * Copyright 2020 Toradex
+ * Copyright 2021 Toradex
  */
 
 #include "imx8mm-u-boot.dtsi"
 
 / {
+	binman: binman {
+		multiple-images;
+	};
+
 	firmware {
 		optee {
 			compatible = "linaro,optee-tz";
@@ -91,3 +95,121 @@
 &wdog1 {
 	u-boot,dm-spl;
 };
+
+&binman {
+	 u-boot-spl-ddr {
+		filename = "u-boot-spl-ddr.bin";
+		pad-byte = <0xff>;
+		align-size = <4>;
+		align = <4>;
+
+		u-boot-spl {
+			align-end = <4>;
+		};
+
+		blob_1: blob-ext@1 {
+			filename = "lpddr4_pmu_train_1d_imem.bin";
+			size = <0x8000>;
+		};
+
+		blob_2: blob-ext@2 {
+			filename = "lpddr4_pmu_train_1d_dmem.bin";
+			size = <0x4000>;
+		};
+
+		blob_3: blob-ext@3 {
+			filename = "lpddr4_pmu_train_2d_imem.bin";
+			size = <0x8000>;
+		};
+
+		blob_4: blob-ext@4 {
+			filename = "lpddr4_pmu_train_2d_dmem.bin";
+			size = <0x4000>;
+		};
+	};
+
+	spl {
+		filename = "spl.bin";
+
+		mkimage {
+			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000";
+
+			blob {
+				filename = "u-boot-spl-ddr.bin";
+			};
+		};
+	};
+
+	itb {
+		filename = "u-boot.itb";
+
+		fit {
+			description = "Configuration to load ATF before U-Boot";
+			#address-cells = <1>;
+			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
+
+			images {
+				uboot {
+					description = "U-Boot (64-bit)";
+					type = "standalone";
+					arch = "arm64";
+					compression = "none";
+					load = <CONFIG_SYS_TEXT_BASE>;
+
+					uboot_blob: blob-ext {
+						filename = "u-boot-nodtb.bin";
+					};
+				};
+
+				atf {
+					description = "ARM Trusted Firmware";
+					type = "firmware";
+					arch = "arm64";
+					compression = "none";
+					load = <0x920000>;
+					entry = <0x920000>;
+
+					atf_blob: blob-ext {
+						filename = "bl31.bin";
+					};
+				};
+
+				fdt {
+					description = "NAME";
+					type = "flat_dt";
+					compression = "none";
+
+					uboot_fdt_blob: blob-ext {
+						filename = "u-boot.dtb";
+					};
+				};
+			};
+
+			configurations {
+				default = "conf";
+
+				conf {
+					description = "NAME";
+					firmware = "uboot";
+					loadables = "atf";
+					fdt = "fdt";
+				};
+			};
+		};
+	};
+
+	imx-boot {
+		filename = "flash.bin";
+		pad-byte = <0x00>;
+
+		spl: blob-ext@1 {
+			offset = <0x0>;
+			filename = "spl.bin";
+		};
+
+		uboot: blob-ext@2 {
+			offset = <0x5fc00>;
+			filename = "u-boot.itb";
+		};
+	};
+};
arch/arm/mach-imx/imx8m/Kconfig +1 -0
index a2ba30cf332..3eccc6b4d4f 100644
@@ -106,6 +106,7 @@ config TARGET_PICO_IMX8MQ
 
 config TARGET_VERDIN_IMX8MM
 	bool "Support Toradex Verdin iMX8M Mini module"
+	select BINMAN
 	select IMX8MM
 	select SUPPORT_SPL
 	select IMX8M_LPDDR4
board/toradex/verdin-imx8mm/imximage.cfg +2 -9
index b8b25ff4201..2832e6ec029 100644
@@ -1,16 +1,9 @@
 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
- * Copyright 2020 Toradex
+ * Copyright 2021 Toradex
  */
 
 #define __ASSEMBLY__
 
-FIT
 BOOT_FROM	emmc_fastboot
-LOADER		spl/u-boot-spl-ddr.bin	0x7E1000
-SECOND_LOADER	u-boot.itb		0x40200000 0x60000
-
-DDR_FW lpddr4_pmu_train_1d_imem.bin
-DDR_FW lpddr4_pmu_train_1d_dmem.bin
-DDR_FW lpddr4_pmu_train_2d_imem.bin
-DDR_FW lpddr4_pmu_train_2d_dmem.bin
+LOADER		u-boot-spl-ddr.bin	0x7e1000
configs/verdin-imx8mm_defconfig +1 -1
index 624f1b99096..b323ceb19af 100644
@@ -24,7 +24,7 @@ CONFIG_DISTRO_DEFAULTS=y
 CONFIG_FIT=y
 CONFIG_FIT_EXTERNAL_OFFSET=0x3000
 CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+# CONFIG_USE_SPL_FIT_GENERATOR is not set
 CONFIG_OF_SYSTEM_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/toradex/verdin-imx8mm/imximage.cfg"
 # CONFIG_USE_BOOTCOMMAND is not set
doc/board/toradex/verdin-imx8mm.rst +30 -23

68 lines not on this page · raw message

Signature · 1 line
2.26.2
Reviewed-by on v3 4/10
#5 lore raw

Re: [PATCH v3 04/10] verdin-imx8mm: switch to use binman to pack images

Hello Marcel,

Quoted 22 lines · Marcel Ziswiler

From: Marcel Ziswiler <[email protected]>

Use binman to pack images.

---

Changes in v3:
- Case fold hex string.
- Revert binman part of imx8mm-verdin-u-boot.dtsi to a plain copy from imx8mm-evk and postpone further improvements to after migrating to a common binman config as agreed with Frieder and Simon.

Changes in v2:
- Explicitly pass filename to binman when generating binaries as suggested by Heiko.
- Use proper intermediate binary u-boot-spl-ddr.bin for imximage as pointed out by Heiko.

Quoted 6 lines
 arch/arm/dts/imx8mm-verdin-u-boot.dtsi   | 124 ++++++++++++++++++++++-
 arch/arm/mach-imx/imx8m/Kconfig          |   1 +
 board/toradex/verdin-imx8mm/imximage.cfg |  11 +-
 configs/verdin-imx8mm_defconfig          |   2 +-
 doc/board/toradex/verdin-imx8mm.rst      |  53 +++++-----
 5 files changed, 157 insertions(+), 34 deletions(-)

bye,
Heiko

Signature · 3 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52   Fax: +49-8142-66989-80   Email: [email protected]
#6 lore raw

PATCH v3 5/10 verdin-imx8mm: enable sleep_moci output

In reply to Marcel Ziswiler

From: Max Krummenacher <[email protected]>

This powers some peripherals on the carrier board e.g. the USB hub.

Related-to: ELB-3206

---

(no changes since v1)

 arch/arm/dts/imx8mm-verdin.dts  | 18 ++++++++++++++++++
 configs/verdin-imx8mm_defconfig |  1 +
 2 files changed, 19 insertions(+)
arch/arm/dts/imx8mm-verdin.dts +18 -0
index ac2a4b69d3c..a2331627d72 100644
@@ -196,6 +196,18 @@
 	};
 };
 
+&gpio5 {
+	ctrl_sleep_moci {
+		gpio-hog;
+		/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
+		gpios = <1 GPIO_ACTIVE_HIGH>;
+		line-name = "CTRL_SLEEP_MOCI#";
+		output-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+	};
+};
+
 /* On-module I2C */
 &i2c1 {
 	clock-frequency = <400000>;
@@ -548,6 +560,12 @@
 		>;
 	};
 
+	pinctrl_ctrl_sleep_moci: ctrlsleepmocigrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1		0x1c4		/* SODIMM 256 */
+		>;
+	};
+
 	pinctrl_dsi_bkl_en: dsi_bkl_en {
 		fsl,pins = <
 			MX8MM_IOMUXC_NAND_CE2_B_GPIO3_IO3	0x1c4		/* SODIMM 21 */
configs/verdin-imx8mm_defconfig +1 -0
index b323ceb19af..ad9c00a3cc4 100644
@@ -71,6 +71,7 @@ CONFIG_SPL_CLK_COMPOSITE_CCF=y
 CONFIG_CLK_COMPOSITE_CCF=y
 CONFIG_SPL_CLK_IMX8MM=y
 CONFIG_CLK_IMX8MM=y
+CONFIG_GPIO_HOG=y
 CONFIG_MXC_GPIO=y
 CONFIG_DM_I2C=y
 CONFIG_SYS_I2C_MXC=y
Signature · 1 line
2.26.2
#7 lore raw

PATCH v3 6/10 verdin-imx8mm: clean-up include order

In reply to Marcel Ziswiler

From: Marcel Ziswiler <[email protected]>

Alphabetically order includes.
While at it also update copyright year resp. period.

---

Changes in v3:
- New patch cleaning up include order.

 board/toradex/verdin-imx8mm/verdin-imx8mm.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
board/toradex/verdin-imx8mm/verdin-imx8mm.c +2 -2
index 1644f4b3081..71ceb26e811 100644
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * Copyright 2020 Toradex
+ * Copyright 2020-2021 Toradex
  */
 
 #include <common.h>
@@ -10,9 +10,9 @@
 #include <asm/global_data.h>
 #include <asm/io.h>
 #include <i2c.h>
+#include <micrel.h>
 #include <miiphy.h>
 #include <netdev.h>
-#include <micrel.h>
 
 #include "../common/tdx-cfg-block.h"
 
Signature · 1 line
2.26.2
#8 lore raw

PATCH v3 7/10 verdin-imx8mm: drop support for v1.0 hardware

In reply to Marcel Ziswiler

From: Max Krummenacher <[email protected]>

We drop support for Verdin iMX8M Mini V1.0B.

Related-to: ELB-3551

---

Changes in v3:
- Add Fabio's reviewed-by tag.

Changes in v2:
- Drop first patch ("imx: mkimage_fit_atf: fix legacy image generation") as a similar fix was already refused earlier.

 board/toradex/verdin-imx8mm/verdin-imx8mm.c | 13 +++++--------
 1 file changed, 5 insertions(+), 8 deletions(-)
board/toradex/verdin-imx8mm/verdin-imx8mm.c +5 -8
index 71ceb26e811..c51c99b5156 100644
@@ -9,6 +9,7 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/global_data.h>
 #include <asm/io.h>
+#include <hang.h>
 #include <i2c.h>
 #include <micrel.h>
 #include <miiphy.h>
@@ -87,17 +88,13 @@ static void select_dt_from_module_version(void)
 
 	switch (get_pcb_revision()) {
 	case PCB_VERSION_1_0:
-		printf("Detected a V1.0 module\n");
-		if (is_wifi)
-			strncpy(&variant[0], "wifi", sizeof(variant));
-		else
-			strncpy(&variant[0], "nonwifi", sizeof(variant));
-		break;
+		printf("Detected a V1.0 module which is no longer supported in this BSP version\n");
+		hang();
 	default:
 		if (is_wifi)
-			strncpy(&variant[0], "wifi-v1.1", sizeof(variant));
+			strlcpy(&variant[0], "wifi", sizeof(variant));
 		else
-			strncpy(&variant[0], "nonwifi-v1.1", sizeof(variant));
+			strlcpy(&variant[0], "nonwifi", sizeof(variant));
 		break;
 	}
 
Signature · 1 line
2.26.2
#9 lore raw

PATCH v3 8/10 include/configs: apalis-imx8/verdin-imx8mm: rename kernel image variable

In reply to Marcel Ziswiler

From: Oleksandr Suvorov <[email protected]>

Variable "kernel_image" is used in boot.scr script only, that sets its own default value to the constant string @@KERNEL_IMAGETYPE@@ in case "kernel_image" is not set.
The default name of the kernel image shipped with BSP 5.x is "Image.gz". Setting kernel_image="Image" as a pre-defined u-boot variable breaks booting systems with modern versions of boot.scr, whereas renaming it fixes booting with modern scripts and does not break working of earlier versions of boot.scr.

---

Changes in v3:
- Fix patch.
- Add missing apalis-imx8 part.
- While at it update copyright year resp. period.
- Fix closing endif comment.

Changes in v2:
- New patch allows booting recent embedded Linux BSPs.

 include/configs/apalis-imx8.h   |  6 +++---
 include/configs/verdin-imx8mm.h | 11 +++++------
 2 files changed, 8 insertions(+), 9 deletions(-)
include/configs/apalis-imx8.h +3 -3
index b04a03f76da..1757f025fc5 100644
@@ -1,6 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
- * Copyright 2019 Toradex
+ * Copyright 2019-2021 Toradex
  */
 
 #ifndef __APALIS_IMX8_H
@@ -44,12 +44,12 @@
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	BOOTENV \
 	MEM_LAYOUT_ENV_SETTINGS \
+	"boot_file=Image\0" \
 	"console=ttyLP1 earlycon\0" \
 	"fdt_addr=0x83000000\0"	\
 	"fdt_file=fsl-imx8qm-apalis-eval.dtb\0" \
 	"fdtfile=fsl-imx8qm-apalis-eval.dtb\0" \
 	"finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \
-	"image=Image\0" \
 	"initrd_addr=0x83800000\0" \
 	"initrd_high=0xffffffffffffffff\0" \
 	"mmcargs=setenv bootargs console=${console},${baudrate} " \
@@ -59,7 +59,7 @@
 	"netargs=setenv bootargs console=${console},${baudrate} " \
 		"root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp" \
 		"\0" \
-	"nfsboot=run netargs; dhcp ${loadaddr} ${image}; tftp ${fdt_addr} " \
+	"nfsboot=run netargs; dhcp ${loadaddr} ${boot_file}; tftp ${fdt_addr} " \
 		"apalis-imx8/${fdt_file}; booti ${loadaddr} - ${fdt_addr}\0" \
 	"panel=NULL\0" \
 	"script=boot.scr\0" \
include/configs/verdin-imx8mm.h +5 -6
index 7be5e5ddf11..d15a3e05fcc 100644
@@ -1,6 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
- * Copyright 2020 Toradex
+ * Copyright 2020-2021 Toradex
  */
 
 #ifndef __VERDIN_IMX8MM_H
@@ -57,16 +57,16 @@
 	BOOTENV \
 	MEM_LAYOUT_ENV_SETTINGS \
 	"bootcmd_mfg=fastboot 0\0" \
+	"boot_file=Image\0" \
 	"console=ttymxc0\0" \
 	"fdt_addr=0x43000000\0" \
-	"fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
+	"fdt_board=dev\0" \
 	"initrd_addr=0x43800000\0" \
 	"initrd_high=0xffffffffffffffff\0" \
-	"kernel_image=Image\0" \
 	"netargs=setenv bootargs console=${console},${baudrate} " \
 		"root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp" \
 		"\0" \
-	"nfsboot=run netargs; dhcp ${loadaddr} ${kernel_image}; " \
+	"nfsboot=run netargs; dhcp ${loadaddr} ${boot_file}; " \
 		"tftp ${fdt_addr} verdin/${fdtfile}; " \
 		"booti ${loadaddr} - ${fdt_addr}\0" \
 	"setup=setenv setupargs console=${console},${baudrate} " \
@@ -124,5 +124,4 @@
 #define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 
-#endif /*_VERDIN_IMX8MM_H */
-
+#endif /* __VERDIN_IMX8MM_H */
Signature · 1 line
2.26.2
#10 lore raw

PATCH v3 9/10 verdin-imx8mm: use preboot for fdtfile evaluation

In reply to Marcel Ziswiler

From: Igor Opaniuk <[email protected]>

Enable and set preboot var with fdtfile evaluation.
It will be checked and run immediately before starting the CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp. entering interactive mode.

This provides possibility to use different boot cmds in interactive mode without manual setting fdtfile value, as it it's already evaluated before entering interactive mode.

---

(no changes since v2)

Changes in v2:
- New patch addressing dynamic fdtfile definition.

 configs/verdin-imx8mm_defconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
configs/verdin-imx8mm_defconfig +2 -1
index ad9c00a3cc4..ab549ebbada 100644
@@ -28,7 +28,8 @@ CONFIG_SPL_LOAD_FIT=y
 CONFIG_OF_SYSTEM_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/toradex/verdin-imx8mm/imximage.cfg"
 # CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_DEFAULT_FDT_FILE="fsl-imx8mm-verdin-dev.dtb"
+CONFIG_USE_PREBOOT=y
+CONFIG_PREBOOT="setenv fdtfile imx8mm-verdin-${variant}-${fdt_board}.dtb"
 CONFIG_LOG=y
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
Signature · 1 line
2.26.2
#11 lore raw

PATCH v3 10/10 verdin-imx8mm: fix watchdog pinctrl issue

In reply to Marcel Ziswiler

From: Marcel Ziswiler <[email protected]>

Finally, found the root cause of the issue already once mentioned back here [2] which caused the following error message during boot:

imx_wdt watchdog@30280000:
pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19

Turns out while the watchdog node itself was already u-boot,dm-spl its pinctrl node was not which caused it to be unavailable at that early stage. Note that any and all other boards I checked also seem to be missing this. However, I can't judge whether or not they might indeed need a similar fix or not.

[2] https://marc.info/?l=u-boot&m=161786572422973

Fixes commit d304e7ace3a6

("ARM: imx8m: Fix reset in SPL on Toradex iMX8MM Verdin")

---

(no changes since v2)

Changes in v2:
- New patch fixing watchdog pinctrl issue.

 arch/arm/dts/imx8mm-verdin-u-boot.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm/dts/imx8mm-verdin-u-boot.dtsi +4 -0
index 0e041865021..6962bb40b6e 100644
@@ -68,6 +68,10 @@
 	u-boot,dm-spl;
 };
 
+&pinctrl_wdog {
+	u-boot,dm-spl;
+};
+
 &{/soc@0/bus@30800000/i2c@30a20000/pmic} {
 	u-boot,dm-spl;
 };
Signature · 1 line
2.26.2