Skip to contentSkip to conversation

Bluetooth: btusb: Support public address configuration for MediaTek Chip.

PATCH In review [email protected] 2 participants 4 messages Sep 1, 2021

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 Bluetooth: btusb: Support public address configuration for MediaTek Chip.

From: "mark-yw.chen" <[email protected]>

The MediaTek chip support vendor specific HCI command(0xfc1a) to change the public address. Add hdev->set_bdaddr handler for MediaTek Chip. After doing a power cycle or MediaTek Bluetooth reset, BD_ADDR will bring back the original one.

---
 drivers/bluetooth/btusb.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
drivers/bluetooth/btusb.c +18 -0
index 60d2fce59a71..41e7c9f28d82 100644
@@ -2200,6 +2200,23 @@ struct btmtk_section_map {
 	};
 } __packed;
 
+static int btusb_set_bdaddr_mtk(struct hci_dev *hdev, const bdaddr_t *bdaddr)
+{
+	struct sk_buff *skb;
+	long ret;
+
+	skb = __hci_cmd_sync(hdev, 0xfc1a, sizeof(bdaddr), bdaddr, HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb)) {
+		ret = PTR_ERR(skb);
+		bt_dev_err(hdev, "changing Mediatek device address failed (%ld)",
+			   ret);
+		return ret;
+	}
+	kfree_skb(skb);
+
+	return 0;
+}
+
 static void btusb_mtk_wmt_recv(struct urb *urb)
 {
 	struct hci_dev *hdev = urb->context;
@@ -3819,6 +3836,7 @@ static int btusb_probe(struct usb_interface *intf,
 		hdev->shutdown = btusb_mtk_shutdown;
 		hdev->manufacturer = 70;
 		hdev->cmd_timeout = btusb_mtk_cmd_timeout;
+		hdev->set_bdaddr = btusb_set_bdaddr_mtk;
 		set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);
 		data->recv_acl = btusb_recv_acl_mtk;
 	}
Signature · 5 lines
2.18.0
_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#1 lore raw

PATCH v2 2/2 Bluetooth: btusb: Add protocol for MediaTek bluetooth devices(MT7922)

From: "mark-yw.chen" <[email protected]>

The information in /sys/kernel/debug/usb/devices about the MT7922U Bluetooth device is listed as the below.

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 18 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0e8d ProdID=7922 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

---
 drivers/bluetooth/btusb.c | 1 +
 1 file changed, 1 insertion(+)
drivers/bluetooth/btusb.c +1 -0
index 41e7c9f28d82..66c8f3cdc0c0 100644
@@ -2821,6 +2821,7 @@ static int btusb_mtk_setup(struct hci_dev *hdev)
 	case 0x7668:
 		fwname = FIRMWARE_MT7668;
 		break;
+	case 0x7922:
 	case 0x7961:
 		snprintf(fw_bin_name, sizeof(fw_bin_name),
 			"mediatek/BT_RAM_CODE_MT%04x_1_%x_hdr.bin",
Signature · 5 lines
2.18.0
_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
maintainer
#2 lore raw

Re: [PATCH v2 2/2] Bluetooth: btusb: Add protocol for MediaTek bluetooth devices(MT7922)

Hi Mark,

Quoted 43 lines

The information in /sys/kernel/debug/usb/devices about the MT7922U Bluetooth device is listed as the below.

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 18 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0e8d ProdID=7922 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Quoted 4 lines

---
drivers/bluetooth/btusb.c | 1 +

1 file changed, 1 insertion(+)

patch has been applied to bluetooth-next tree.

Regards

Marcel

maintainer
#3 lore raw
In reply to [email protected]

Hi Mark,

Quoted 9 lines

The MediaTek chip support vendor specific HCI command(0xfc1a) to change the public address. Add hdev->set_bdaddr handler for MediaTek Chip. After doing a power cycle or MediaTek Bluetooth reset, BD_ADDR will bring back the original one.

---
drivers/bluetooth/btusb.c | 18 ++++++++++++++++++

1 file changed, 18 insertions(+)

patch has been applied to bluetooth-next tree.

Regards

Marcel