Skip to contentSkip to conversation

arm64: dts: initial NXP S32G2 support

PATCH Applied Chester Lin 3 participants 12 messages Sep 8, 2021 – Oct 4, 2021

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v2 cover arm64: dts: initial NXP S32G2 support

Hello,

Here I'd like to propose a patchset, which is initial upstream support for NXP S32G2. S32G is a processor family developed by NXP for automotive solutions, such as vehicle networking and automotive high-performance processing. This series focuses on S32G2, which is the latest generation we can find at the moment. As the first round to support S32G2, this patchset only enables basic components and interfaces the SoC must have while kernel booting, which aims to have minimum hardware enablement for these two boards, S32G-VNP-EVB and S32G-VNP-RDB2. The concepts of how these boards work are originated from the downstream kernel tree[1] developed by NXP, which provides lots of details about the SoC S32G274A and its integrated boards. This series has been verified with downstream ATF[2] & U-Boot[3] based on the ATF boot flow.

Thanks,
Chester

[1] https://source.codeaurora.org/external/autobsps32/linux/
[2] https://source.codeaurora.org/external/autobsps32/arm-trusted-firmware/
[3] https://source.codeaurora.org/external/autobsps32/u-boot/

Changes in v2:
- dt-bindings:
- Rename the compatible vendor string to "nxp," for s32g2.
- Drop the specific description "S32V234 SoC".
- Fill my name in the maintainer field. I tried to contact the authors of fsl,s32-linflexuart.txt but got no response.
- Remove redundant minItems/maxItems from compatible properties.
- Remove the redundant example from fsl,s32-linflexuart.yaml.
- dtsi/dts:
- Add a SoC description in s32g2.dtsi.
- Add an interrupt-affinity to the pmu node.
- Move the psci node into the "/firmware" node.
- Remove the redundant properties and white lines in DT.
- Remove the wrong interrupt specifier from the gic node.
- Specify the range and cell-size of /soc [0 - 4 GiB].
- Correct the reserved size of GICR to 512Kbytes [0x80000].
- Add new Signed-off-by to the DT uart patch.
- Fix copyright strings.
- Revise reg properties based on new cell-size.
- Move the serial/uart aliases from the SoC .dtsi to board .dts files.
- Correct the model string of RDB2.
- Add comments for the uart markings on PCB.
- Adjust RAM size comments of memory nodes.
- Convert reg addresses of memory nodes into hex format.
- MAINTAINERS
- Add information of reviewers.

Chester Lin (8):
dt-bindings: arm: fsl: add NXP S32G2 boards
dt-bindings: serial: fsl-linflexuart: convert to json-schema format
dt-bindings: serial: fsl-linflexuart: add compatible for S32G2
arm64: dts: add NXP S32G2 support
arm64: dts: s32g2: add serial/uart support
arm64: dts: s32g2: add VNP-EVB and VNP-RDB2 support
arm64: dts: s32g2: add memory nodes for evb and rdb2
MAINTAINERS: add an entry for NXP S32G boards

 .../devicetree/bindings/arm/fsl.yaml          |   7 +
 .../bindings/serial/fsl,s32-linflexuart.txt   |  22 ----
 .../bindings/serial/fsl,s32-linflexuart.yaml  |  48 +++++++
 MAINTAINERS                                   |   9 ++
 arch/arm64/boot/dts/freescale/Makefile        |   2 +
 arch/arm64/boot/dts/freescale/s32g2.dtsi      | 124 ++++++++++++++++++
 .../arm64/boot/dts/freescale/s32g274a-evb.dts |  34 +++++
 .../boot/dts/freescale/s32g274a-rdb2.dts      |  40 ++++++
 8 files changed, 264 insertions(+), 22 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.txt
 create mode 100644 Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.yaml
 create mode 100644 arch/arm64/boot/dts/freescale/s32g2.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/s32g274a-evb.dts
 create mode 100644 arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts
Signature · 1 line
2.30.0
#1 lore raw

PATCH v2 1/8 dt-bindings: arm: fsl: add NXP S32G2 boards

Add bindings for S32G2's evaluation board (S32G-VNP-EVB) and reference design board 2 ( S32G-VNP-RDB2).

---
Changes in v2:
- Rename the vendor string to "nxp,".

 Documentation/devicetree/bindings/arm/fsl.yaml | 7 +++++++
 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/arm/fsl.yaml +7 -0
index 60f4862ba15e..12ab7ac565fb 100644
@@ -990,6 +990,13 @@ properties:
           - const: solidrun,lx2160a-cex7
           - const: fsl,lx2160a
 
+      - description: S32G2 based Boards
+        items:
+          - enum:
+              - nxp,s32g274a-evb
+              - nxp,s32g274a-rdb2
+          - const: nxp,s32g2
+
       - description: S32V234 based Boards
         items:
           - enum:
Signature · 1 line
2.30.0
#2 lore raw

PATCH v2 2/8 dt-bindings: serial: fsl-linflexuart: convert to json-schema format

In reply to Chester Lin

Convert the FSL LINFlexD UART binding to json-schema.

---
Changes in v2:
- Drop the specific description "S32V234 SoC".
- Fill my name in the maintainer field. I tried to contact the authors of fsl,s32-linflexuart.txt but got no response.

 .../bindings/serial/fsl,s32-linflexuart.txt   | 22 ---------
 .../bindings/serial/fsl,s32-linflexuart.yaml  | 46 +++++++++++++++++++
 2 files changed, 46 insertions(+), 22 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.txt
 create mode 100644 Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.yaml
Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.txt deleted +0 -22
deleted file mode 100644
index f1bbe0826be5..000000000000
@@ -1,22 +0,0 @@
-* Freescale LINFlexD UART
-
-The LINFlexD controller implements several LIN protocol versions, as well as
-support for full-duplex UART communication through 8-bit and 9-bit frames.
-
-See chapter 47 ("LINFlexD") in the reference manual[1].
-
-Required properties:
-- compatible :
-  - "fsl,s32v234-linflexuart" for LINFlexD configured in UART mode, which
-    is compatible with the one integrated on S32V234 SoC
-- reg : Address and length of the register set for the device
-- interrupts : Should contain uart interrupt
-
-Example:
-uart0: serial@40053000 {
-	compatible = "fsl,s32v234-linflexuart";
-	reg = <0x0 0x40053000 0x0 0x1000>;
-	interrupts = <0 59 4>;
-};
-
-[1] https://www.nxp.com/webapp/Download?colCode=S32V234RM
Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.yaml new file +46 -0

46 lines not on this page · raw message

Signature · 1 line
2.30.0
maintainer Reviewed-by on v2 2/8
#3 lore raw

Re: [PATCH v2 2/8] dt-bindings: serial: fsl-linflexuart: convert to json-schema format

Quoted 10 lines · Chester Lin

Convert the FSL LINFlexD UART binding to json-schema.

---
Changes in v2:
- Drop the specific description "S32V234 SoC".
- Fill my name in the maintainer field. I tried to contact the authors of fsl,s32-linflexuart.txt but got no response.

Quoted 6 lines
 .../bindings/serial/fsl,s32-linflexuart.txt   | 22 ---------
 .../bindings/serial/fsl,s32-linflexuart.yaml  | 46 +++++++++++++++++++
 2 files changed, 46 insertions(+), 22 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.txt
 create mode 100644 Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.yaml
#4 lore raw

PATCH v2 3/8 dt-bindings: serial: fsl-linflexuart: add compatible for S32G2

In reply to Chester Lin

Add a compatible string for the uart binding of NXP S32G2 platforms. Here we use "s32v234-linflexuart" as fallback since the current linflexuart driver can still work on S32G2.

---
Changes in v2:
- Remove redundant minItems/maxItems from compatible properties.
- Remove the redundant example.
- Rename the vendor string to "nxp," for s32g2.

 .../devicetree/bindings/serial/fsl,s32-linflexuart.yaml     | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.yaml +4 -2
index b6fc123e8375..8b643bae3c7b 100644
@@ -20,9 +20,11 @@ allOf:
 
 properties:
   compatible:
-    description: The LINFlexD controller in UART mode.
-    items:
+    oneOf:
       - const: fsl,s32v234-linflexuart
+      - items:
+          - const: nxp,s32g2-linflexuart
+          - const: fsl,s32v234-linflexuart
 
   reg:
     maxItems: 1
Signature · 1 line
2.30.0
maintainer Reviewed-by on v2 3/8
#5 lore raw

Re: [PATCH v2 3/8] dt-bindings: serial: fsl-linflexuart: add compatible for S32G2

Quoted 5 lines · Chester Lin

Add a compatible string for the uart binding of NXP S32G2 platforms. Here we use "s32v234-linflexuart" as fallback since the current linflexuart driver can still work on S32G2.

Quoted 9 lines

---
Changes in v2:
- Remove redundant minItems/maxItems from compatible properties.
- Remove the redundant example.
- Rename the vendor string to "nxp," for s32g2.

 .../devicetree/bindings/serial/fsl,s32-linflexuart.yaml     | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
#6 lore raw

PATCH v2 4/8 arm64: dts: add NXP S32G2 support

In reply to Chester Lin

Add an initial dtsi file for generic SoC features of NXP S32G2.

---
Changes in v2:
- Add a SoC description.
- Add an interrupt-affinity to the pmu node.
- Move the psci node into the "/firmware" node.
- Remove the redundant properties and white lines.
- Remove the wrong interrupt specifier from the gic node.
- Specify the range and cell-size of /soc [0 - 4 GiB].
- Correct the reserved size of GICR to 512KiB [0x80000].

 arch/arm64/boot/dts/freescale/s32g2.dtsi | 99 ++++++++++++++++++++++++
 1 file changed, 99 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/s32g2.dtsi
arch/arm64/boot/dts/freescale/s32g2.dtsi new file +99 -0
new file mode 100644
index 000000000000..53b18671deec
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * NXP S32G2 SoC family
+ *
+ * Copyright (c) 2021 SUSE LLC
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "nxp,s32g2";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			next-level-cache = <&cluster0_l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			enable-method = "psci";
+			next-level-cache = <&cluster0_l2>;
+		};
+
+		cpu2: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x100>;
+			enable-method = "psci";
+			next-level-cache = <&cluster1_l2>;
+		};
+
+		cpu3: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x101>;
+			enable-method = "psci";
+			next-level-cache = <&cluster1_l2>;
+		};
+
+		cluster0_l2: l2-cache0 {
+			compatible = "cache";
+		};
+
+		cluster1_l2: l2-cache1 {
+			compatible = "cache";
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	firmware {
+		psci {
+			compatible = "arm,psci-1.0";
+			method = "smc";
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0x80000000>;
+
+		gic: interrupt-controller@50800000 {
+			compatible = "arm,gic-v3";
+			reg = <0x50800000 0x10000>,
+			      <0x50880000 0x80000>,
+			      <0x50400000 0x2000>,
+			      <0x50410000 0x2000>,
+			      <0x50420000 0x2000>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+	};
+};
Signature · 1 line
2.30.0
#7 lore raw

PATCH v2 5/8 arm64: dts: s32g2: add serial/uart support

In reply to Chester Lin

Add serial/uart support for NXP S32G2 based on the information provided by NXP's CodeAurora BSP.

---
Changes in v2:
- Add new Signed-off-by.
- Fix the copyright string.
- Remove aliases.
- Revise reg properties based on new cell size.

 arch/arm64/boot/dts/freescale/s32g2.dtsi | 25 ++++++++++++++++++++++++
 1 file changed, 25 insertions(+)
arch/arm64/boot/dts/freescale/s32g2.dtsi +25 -0
index 53b18671deec..59ea8a25aa4c 100644
@@ -3,6 +3,7 @@
  * NXP S32G2 SoC family
  *
  * Copyright (c) 2021 SUSE LLC
+ * Copyright (c) 2017-2021 NXP
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -84,6 +85,30 @@ soc {
 		#size-cells = <1>;
 		ranges = <0 0 0 0x80000000>;
 
+		uart0: serial@401c8000 {
+			compatible = "nxp,s32g2-linflexuart",
+				     "fsl,s32v234-linflexuart";
+			reg = <0x401c8000 0x3000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+		};
+
+		uart1: serial@401cc000 {
+			compatible = "nxp,s32g2-linflexuart",
+				     "fsl,s32v234-linflexuart";
+			reg = <0x401cc000 0x3000>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+		};
+
+		uart2: serial@402bc000 {
+			compatible = "nxp,s32g2-linflexuart",
+				     "fsl,s32v234-linflexuart";
+			reg = <0x402bc000 0x3000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+		};
+
 		gic: interrupt-controller@50800000 {
 			compatible = "arm,gic-v3";
 			reg = <0x50800000 0x10000>,
Signature · 1 line
2.30.0
#8 lore raw

PATCH v2 6/8 arm64: dts: s32g2: add VNP-EVB and VNP-RDB2 support

In reply to Chester Lin

Add initial device-trees of NXP S32G2's Evaluation Board (S32G-VNP-EVB) and Reference Design 2 Board (S32G-VNP-RDB2).

---
Changes in v2:
- Correct the model string.
- Rename the compatible vendor string to "nxp,".
- Move the serial/uart aliases from the SoC .dtsi to board .dts files.
- Add comments for the uart markings on PCB.

 arch/arm64/boot/dts/freescale/Makefile        |  2 ++
 .../arm64/boot/dts/freescale/s32g274a-evb.dts | 26 +++++++++++++++
 .../boot/dts/freescale/s32g274a-rdb2.dts      | 32 +++++++++++++++++++
 3 files changed, 60 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/s32g274a-evb.dts
 create mode 100644 arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts
arch/arm64/boot/dts/freescale/Makefile +2 -0
index db9e36ebe932..0d4a18bd83e6 100644
@@ -70,4 +70,6 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-eval-v3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
 
+dtb-$(CONFIG_ARCH_S32) += s32g274a-evb.dtb
+dtb-$(CONFIG_ARCH_S32) += s32g274a-rdb2.dtb
 dtb-$(CONFIG_ARCH_S32) += s32v234-evb.dtb
arch/arm64/boot/dts/freescale/s32g274a-evb.dts new file +26 -0
new file mode 100644
index 000000000000..3aec05de0842
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 SUSE LLC
+ */
+
+/dts-v1/;
+
+#include "s32g2.dtsi"
+
+/ {
+	model = "NXP S32G2 Evaluation Board (S32G-VNP-EVB)";
+	compatible = "nxp,s32g274a-evb", "nxp,s32g2";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+/* UART (J58) to Micro USB port */
+&uart0 {
+	status = "okay";
+};
arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts new file +32 -0
new file mode 100644
index 000000000000..ed3f23babdca
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 SUSE LLC
+ */
+
+/dts-v1/;
+
+#include "s32g2.dtsi"
+
+/ {
+	model = "NXP S32G2 Reference Design Board 2 (S32G-VNP-RDB2)";
+	compatible = "nxp,s32g274a-rdb2", "nxp,s32g2";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+/* UART (J2) to Micro USB port */
+&uart0 {
+	status = "okay";
+};
+
+/* UART (J1) to Micro USB port */
+&uart1 {
+	status = "okay";
+};
Signature · 1 line
2.30.0
#9 lore raw

PATCH v2 7/8 arm64: dts: s32g2: add memory nodes for evb and rdb2

In reply to Chester Lin

Add memory nodes for S32G-VNP-EVB and S32G-VNP-RDB2.

---
Changes in v2:
- Modify the patch description.
- Fix the copyright string.
- Adjust RAM size comments.
- Convert reg addresses of memory nodes into hex format.

 arch/arm64/boot/dts/freescale/s32g274a-evb.dts  | 8 ++++++++
 arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts | 8 ++++++++
 2 files changed, 16 insertions(+)
arch/arm64/boot/dts/freescale/s32g274a-evb.dts +8 -0
index 3aec05de0842..9118d8d2ee01 100644
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
  * Copyright (c) 2021 SUSE LLC
+ * Copyright (c) 2019-2021 NXP
  */
 
 /dts-v1/;
@@ -18,6 +19,13 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	/* 4GiB RAM */
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0 0x80000000>,
+		      <0x8 0x80000000 0 0x80000000>;
+	};
 };
 
 /* UART (J58) to Micro USB port */
arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts +8 -0
index ed3f23babdca..e05ee854cdf5 100644
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
  * Copyright (c) 2021 SUSE LLC
+ * Copyright (c) 2019-2021 NXP
  */
 
 /dts-v1/;
@@ -19,6 +20,13 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	/* 4GiB RAM */
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0 0x80000000>,
+		      <0x8 0x80000000 0 0x80000000>;
+	};
 };
 
 /* UART (J2) to Micro USB port */
Signature · 1 line
2.30.0
#10 lore raw

PATCH v2 8/8 MAINTAINERS: add an entry for NXP S32G boards

In reply to Chester Lin

Add a new entry for the maintenance of NXP S32G DT files.

---
Changes in v2:
- Add information of reviewers.

 MAINTAINERS | 9 +++++++++
 1 file changed, 9 insertions(+)
MAINTAINERS +8 -0
index 5a61cb2d0cd4..6f2a3f8ae88e 100644
@@ -2308,6 +2308,14 @@ F:	arch/arm/boot/dts/nuvoton-wpcm450*
 F:	arch/arm/mach-npcm/wpcm450.c
 F:	drivers/*/*wpcm*
 
+ARM/NXP S32G ARCHITECTURE
+M:	Chester Lin <[email protected]>
+R:	Andreas Färber <[email protected]>
+R:	Matthias Brugger <[email protected]>
+L:	[email protected] (moderated for non-subscribers)
+S:	Maintained
+F:	arch/arm64/boot/dts/freescale/s32g*.dts*
+
 ARM/OPENMOKO NEO FREERUNNER (GTA02) MACHINE SUPPORT
 L:	[email protected] (subscribers-only)
 S:	Orphan
Signature · 1 line
2.30.0
Applied
#11 lore raw
In reply to Chester Lin
Quoted 48 lines · Chester Lin

Hello,

Here I'd like to propose a patchset, which is initial upstream support for NXP S32G2. S32G is a processor family developed by NXP for automotive solutions, such as vehicle networking and automotive high-performance processing. This series focuses on S32G2, which is the latest generation we can find at the moment. As the first round to support S32G2, this patchset only enables basic components and interfaces the SoC must have while kernel booting, which aims to have minimum hardware enablement for these two boards, S32G-VNP-EVB and S32G-VNP-RDB2. The concepts of how these boards work are originated from the downstream kernel tree[1] developed by NXP, which provides lots of details about the SoC S32G274A and its integrated boards. This series has been verified with downstream ATF[2] & U-Boot[3] based on the ATF boot flow.

Thanks,
Chester

[1] https://source.codeaurora.org/external/autobsps32/linux/
[2] https://source.codeaurora.org/external/autobsps32/arm-trusted-firmware/
[3] https://source.codeaurora.org/external/autobsps32/u-boot/

Changes in v2:
- dt-bindings:
- Rename the compatible vendor string to "nxp," for s32g2.
- Drop the specific description "S32V234 SoC".
- Fill my name in the maintainer field. I tried to contact the authors of fsl,s32-linflexuart.txt but got no response.
- Remove redundant minItems/maxItems from compatible properties.
- Remove the redundant example from fsl,s32-linflexuart.yaml.
- dtsi/dts:
- Add a SoC description in s32g2.dtsi.
- Add an interrupt-affinity to the pmu node.
- Move the psci node into the "/firmware" node.
- Remove the redundant properties and white lines in DT.
- Remove the wrong interrupt specifier from the gic node.
- Specify the range and cell-size of /soc [0 - 4 GiB].
- Correct the reserved size of GICR to 512Kbytes [0x80000].
- Add new Signed-off-by to the DT uart patch.
- Fix copyright strings.
- Revise reg properties based on new cell-size.
- Move the serial/uart aliases from the SoC .dtsi to board .dts files.
- Correct the model string of RDB2.
- Add comments for the uart markings on PCB.
- Adjust RAM size comments of memory nodes.
- Convert reg addresses of memory nodes into hex format.
- MAINTAINERS
- Add information of reviewers.

Quoted 9 lines

Chester Lin (8):
dt-bindings: arm: fsl: add NXP S32G2 boards
dt-bindings: serial: fsl-linflexuart: convert to json-schema format
dt-bindings: serial: fsl-linflexuart: add compatible for S32G2
arm64: dts: add NXP S32G2 support
arm64: dts: s32g2: add serial/uart support
arm64: dts: s32g2: add VNP-EVB and VNP-RDB2 support
arm64: dts: s32g2: add memory nodes for evb and rdb2
MAINTAINERS: add an entry for NXP S32G boards

Applied all, thanks!