Skip to contentSkip to conversation

Add imx8ulp clock & reset driver support

PATCH In review Jacky Bai 3 participants 26 messages Sep 14, 2021 – Sep 20, 2021

Subsystems (5)
lore
Share & tools
lore

Jacky Bai

author
#0 lore raw

v3 cover Add imx8ulp clock & reset driver support

This patchset adds the clock & reset driver support for i.MX8ULP. For some of the PCC slot, As there is a SWRST control bit share the same pcc register for peripheral reset ccontrol. To simplify the case, register the pcc reset controller driver when pcc clock driver is registered.

Patch 1/9 for the dt-bindings part is send out for review previously with the dts patchset:
https://patchwork.kernel.org/project/linux-arm-kernel/cover/[email protected]/

Shawn suggests to send out the clock driver part firstly, so this patch is included in this patchset for now.

v3 changes:
- split the clock dt schema file into two file, one for pcc, one for cgc

v2 changes:
- remove the useless clocks & clock-names from the dt-binding doc
- remove the redundant fixed clock register.

Anson Huang (1):
clk: imx: disable i.mx7ulp composite clock during initialization

Jacky Bai (8):
dt-bindings: clock: Add imx8ulp clock support
clk: imx: Update the pllv4 to support imx8ulp
clk: imx: Update the compsite driver to support imx8ulp
clk: imx: Add 'CLK_SET_RATE_NO_REPARENT' for composite-7ulp
clk: imx: disable the pfd when set pfdv2 clock rate
clk: imx: Update the pfdv2 for 8ulp specific support
clk: imx: Add clock driver for imx8ulp
clk: imx: Add the pcc reset controller support on imx8ulp

 .../bindings/clock/imx8ulp-cgc-clock.yaml     |  43 ++
 .../bindings/clock/imx8ulp-pcc-clock.yaml     |  50 ++
 drivers/clk/imx/Kconfig                       |   6 +
 drivers/clk/imx/Makefile                      |   2 +
 drivers/clk/imx/clk-composite-7ulp.c          |  87 ++-
 drivers/clk/imx/clk-imx7ulp.c                 |  20 +-
 drivers/clk/imx/clk-imx8ulp.c                 | 569 ++++++++++++++++++
 drivers/clk/imx/clk-pfdv2.c                   |  22 +-
 drivers/clk/imx/clk-pllv4.c                   |  34 +-
 drivers/clk/imx/clk.h                         |  24 +-
 include/dt-bindings/clock/imx8ulp-clock.h     | 258 ++++++++
 include/dt-bindings/reset/imx8ulp-pcc-reset.h |  59 ++
 12 files changed, 1142 insertions(+), 32 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml
 create mode 100644 Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml
 create mode 100644 drivers/clk/imx/clk-imx8ulp.c
 create mode 100644 include/dt-bindings/clock/imx8ulp-clock.h
 create mode 100644 include/dt-bindings/reset/imx8ulp-pcc-reset.h
Signature · 1 line
2.26.2
author
#1 lore raw

PATCH v3 1/9 dt-bindings: clock: Add imx8ulp clock support

Add the clock dt-binding file for i.MX8ULP.

For pcc node, it will also be used as a reset controller, so add the '#reset-cells' property description and add the pcc reset IDs.

---
v3 changes:
- split into two binding file, one for pcc, one for cgc

v2 changes:
- removed the redundant clocks & clock-names property

v1 changes:
- Move this patch from dts patchset into this patchset

---
 .../bindings/clock/imx8ulp-cgc-clock.yaml     |  43 +++
 .../bindings/clock/imx8ulp-pcc-clock.yaml     |  50 ++++
 include/dt-bindings/clock/imx8ulp-clock.h     | 258 ++++++++++++++++++
 include/dt-bindings/reset/imx8ulp-pcc-reset.h |  59 ++++
 4 files changed, 410 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml
 create mode 100644 Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml
 create mode 100644 include/dt-bindings/clock/imx8ulp-clock.h
 create mode 100644 include/dt-bindings/reset/imx8ulp-pcc-reset.h
Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml new file +43 -0
new file mode 100644
index 000000000000..71f7186b135b
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/imx8ulp-cgc-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX8ULP Clock Generation & Control(CGC) Module Binding
+
+maintainers:
+  - Jacky Bai <[email protected]>
+
+description: |
+  On i.MX8ULP, The clock sources generation, distribution and management is
+  under the control of several CGCs & PCCs modules. The CGC modules generate
+  and distribute clocks on the device.
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx8ulp-cgc1
+      - fsl,imx8ulp-cgc2
+
+  reg:
+    maxItems: 1
+
+  '#clock-cells':
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+  # Clock Generation & Control Module node:
+  - |
+    clock-controller@292c0000 {
+        compatible = "fsl,imx8ulp-cgc1";
+        reg = <0x292c0000 0x10000>;
+        #clock-cells = <1>;
+    };
Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml new file +50 -0

50 lines not on this page · raw message

include/dt-bindings/clock/imx8ulp-clock.h new file +258 -0

258 lines not on this page · raw message

include/dt-bindings/reset/imx8ulp-pcc-reset.h new file +59 -0

59 lines not on this page · raw message

Signature · 1 line
2.26.2
#2 lore raw

Re: [PATCH v3 1/9] dt-bindings: clock: Add imx8ulp clock support

Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml

Quoted 28 lines · Jacky Bai

Add the clock dt-binding file for i.MX8ULP.

For pcc node, it will also be used as a reset controller, so add the '#reset-cells' property description and add the pcc reset IDs.

---
v3 changes:
- split into two binding file, one for pcc, one for cgc

v2 changes:
- removed the redundant clocks & clock-names property

v1 changes:
- Move this patch from dts patchset into this patchset

---
 .../bindings/clock/imx8ulp-cgc-clock.yaml     |  43 +++
 .../bindings/clock/imx8ulp-pcc-clock.yaml     |  50 ++++
 include/dt-bindings/clock/imx8ulp-clock.h     | 258 ++++++++++++++++++
 include/dt-bindings/reset/imx8ulp-pcc-reset.h |  59 ++++
 4 files changed, 410 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml
 create mode 100644 Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml
 create mode 100644 include/dt-bindings/clock/imx8ulp-clock.h
 create mode 100644 include/dt-bindings/reset/imx8ulp-pcc-reset.h
Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml +0 -0

I'm not sure but I think the Documentation part is usually done in a separate patch.

Quoted 436 lines

new file mode 100644
index 000000000000..71f7186b135b

Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml new file +43 -0
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/imx8ulp-cgc-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX8ULP Clock Generation & Control(CGC) Module Binding
+
+maintainers:
+  - Jacky Bai <[email protected]>
+
+description: |
+  On i.MX8ULP, The clock sources generation, distribution and management is
+  under the control of several CGCs & PCCs modules. The CGC modules generate
+  and distribute clocks on the device.
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx8ulp-cgc1
+      - fsl,imx8ulp-cgc2
+
+  reg:
+    maxItems: 1
+
+  '#clock-cells':
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+  # Clock Generation & Control Module node:
+  - |
+    clock-controller@292c0000 {
+        compatible = "fsl,imx8ulp-cgc1";
+        reg = <0x292c0000 0x10000>;
+        #clock-cells = <1>;
+    };
Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml new file +50 -0
new file mode 100644
index 000000000000..00612725bf8b
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/imx8ulp-pcc-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX8ULP Peripheral Clock Controller(PCC) Module Binding
+
+maintainers:
+  - Jacky Bai <[email protected]>
+
+description: |
+  On i.MX8ULP, The clock sources generation, distribution and management is
+  under the control of several CGCs & PCCs modules. The PCC modules control
+  software reset, clock selection, optional division and clock gating mode
+  for peripherals.
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx8ulp-pcc3
+      - fsl,imx8ulp-pcc4
+      - fsl,imx8ulp-pcc5
+
+  reg:
+    maxItems: 1
+
+  '#clock-cells':
+    const: 1
+
+  '#reset-cells':
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+  - '#reset-cells'
+
+additionalProperties: false
+
+examples:
+  # Peripheral Clock Control Module node:
+  - |
+    clock-controller@292d0000 {
+        compatible = "fsl,imx8ulp-pcc3";
+        reg = <0x292d0000 0x10000>;
+        #clock-cells = <1>;
+        #reset-cells = <1>;
+    };
include/dt-bindings/clock/imx8ulp-clock.h new file +258 -0
new file mode 100644
index 000000000000..953ecfe8ebcc
@@ -0,0 +1,258 @@
+/* SPDX-License-Identifier: GPL-2.0+ OR MIT */
+/*
+ * Copyright 2021 NXP
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_IMX8ULP_H
+#define __DT_BINDINGS_CLOCK_IMX8ULP_H
+
+#define IMX8ULP_CLK_DUMMY			0
+
+/* CGC1 */
+#define IMX8ULP_CLK_SPLL2			5
+#define IMX8ULP_CLK_SPLL3			6
+#define IMX8ULP_CLK_A35_SEL			7
+#define IMX8ULP_CLK_A35_DIV			8
+#define IMX8ULP_CLK_SPLL2_PRE_SEL		9
+#define IMX8ULP_CLK_SPLL3_PRE_SEL		10
+#define IMX8ULP_CLK_SPLL3_PFD0			11
+#define IMX8ULP_CLK_SPLL3_PFD1			12
+#define IMX8ULP_CLK_SPLL3_PFD2			13
+#define IMX8ULP_CLK_SPLL3_PFD3			14
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV1		15
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV2		16
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV1		17
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV2		18
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV1		19
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV2		20
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV1		21
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV2		22
+#define IMX8ULP_CLK_NIC_SEL			23
+#define IMX8ULP_CLK_NIC_AD_DIVPLAT		24
+#define IMX8ULP_CLK_NIC_PER_DIVPLAT		25
+#define IMX8ULP_CLK_XBAR_SEL			26
+#define IMX8ULP_CLK_XBAR_AD_DIVPLAT		27
+#define IMX8ULP_CLK_XBAR_DIVBUS			28
+#define IMX8ULP_CLK_XBAR_AD_SLOW		29
+#define IMX8ULP_CLK_SOSC_DIV1			30
+#define IMX8ULP_CLK_SOSC_DIV2			31
+#define IMX8ULP_CLK_SOSC_DIV3			32
+#define IMX8ULP_CLK_FROSC_DIV1			33
+#define IMX8ULP_CLK_FROSC_DIV2			34
+#define IMX8ULP_CLK_FROSC_DIV3			35
+#define IMX8ULP_CLK_SPLL3_VCODIV		36
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV1_GATE	37
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV2_GATE	38
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV1_GATE	39
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV2_GATE	40
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV1_GATE	41
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV2_GATE	42
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV1_GATE	43
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV2_GATE	44
+#define IMX8ULP_CLK_SOSC_DIV1_GATE		45
+#define IMX8ULP_CLK_SOSC_DIV2_GATE		46
+#define IMX8ULP_CLK_SOSC_DIV3_GATE		47
+#define IMX8ULP_CLK_FROSC_DIV1_GATE		48
+#define IMX8ULP_CLK_FROSC_DIV2_GATE		49
+#define IMX8ULP_CLK_FROSC_DIV3_GATE		50
+#define IMX8ULP_CLK_SAI4_SEL			51
+#define IMX8ULP_CLK_SAI5_SEL			52
+#define IMX8ULP_CLK_AUD_CLK1			53
+#define IMX8ULP_CLK_ARM				54
+#define IMX8ULP_CLK_ENET_TS_SEL			55
+
+#define IMX8ULP_CLK_CGC1_END			56
+
+/* CGC2 */
+#define IMX8ULP_CLK_PLL4_PRE_SEL	0
+#define IMX8ULP_CLK_PLL4		1
+#define IMX8ULP_CLK_PLL4_VCODIV		2
+#define IMX8ULP_CLK_DDR_SEL		3
+#define IMX8ULP_CLK_DDR_DIV		4
+#define IMX8ULP_CLK_LPAV_AXI_SEL	5
+#define IMX8ULP_CLK_LPAV_AXI_DIV	6
+#define IMX8ULP_CLK_LPAV_AHB_DIV	7
+#define IMX8ULP_CLK_LPAV_BUS_DIV	8
+#define IMX8ULP_CLK_PLL4_PFD0		9
+#define IMX8ULP_CLK_PLL4_PFD1		10
+#define IMX8ULP_CLK_PLL4_PFD2		11
+#define IMX8ULP_CLK_PLL4_PFD3		12
+#define IMX8ULP_CLK_PLL4_PFD0_DIV1_GATE	13
+#define IMX8ULP_CLK_PLL4_PFD0_DIV2_GATE	14
+#define IMX8ULP_CLK_PLL4_PFD1_DIV1_GATE	15
+#define IMX8ULP_CLK_PLL4_PFD1_DIV2_GATE	16
+#define IMX8ULP_CLK_PLL4_PFD2_DIV1_GATE	17
+#define IMX8ULP_CLK_PLL4_PFD2_DIV2_GATE	18
+#define IMX8ULP_CLK_PLL4_PFD3_DIV1_GATE	19
+#define IMX8ULP_CLK_PLL4_PFD3_DIV2_GATE	20
+#define IMX8ULP_CLK_PLL4_PFD0_DIV1	21
+#define IMX8ULP_CLK_PLL4_PFD0_DIV2	22
+#define IMX8ULP_CLK_PLL4_PFD1_DIV1	23
+#define IMX8ULP_CLK_PLL4_PFD1_DIV2	24
+#define IMX8ULP_CLK_PLL4_PFD2_DIV1	25
+#define IMX8ULP_CLK_PLL4_PFD2_DIV2	26
+#define IMX8ULP_CLK_PLL4_PFD3_DIV1	27
+#define IMX8ULP_CLK_PLL4_PFD3_DIV2	28
+#define IMX8ULP_CLK_CGC2_SOSC_DIV1_GATE	29
+#define IMX8ULP_CLK_CGC2_SOSC_DIV2_GATE	30
+#define IMX8ULP_CLK_CGC2_SOSC_DIV3_GATE	31
+#define IMX8ULP_CLK_CGC2_SOSC_DIV1	32
+#define IMX8ULP_CLK_CGC2_SOSC_DIV2	33
+#define IMX8ULP_CLK_CGC2_SOSC_DIV3	34
+#define IMX8ULP_CLK_CGC2_FROSC_DIV1_GATE	35
+#define IMX8ULP_CLK_CGC2_FROSC_DIV2_GATE	36
+#define IMX8ULP_CLK_CGC2_FROSC_DIV3_GATE	37
+#define IMX8ULP_CLK_CGC2_FROSC_DIV1	38
+#define IMX8ULP_CLK_CGC2_FROSC_DIV2	39
+#define IMX8ULP_CLK_CGC2_FROSC_DIV3	40
+#define IMX8ULP_CLK_AUD_CLK2		41
+#define IMX8ULP_CLK_SAI6_SEL		42
+#define IMX8ULP_CLK_SAI7_SEL		43
+#define IMX8ULP_CLK_SPDIF_SEL		44
+#define IMX8ULP_CLK_HIFI_SEL		45
+#define IMX8ULP_CLK_HIFI_DIVCORE	46
+#define IMX8ULP_CLK_HIFI_DIVPLAT	47
+#define IMX8ULP_CLK_DSI_PHY_REF		48
+
+#define IMX8ULP_CLK_CGC2_END		49
+
+/* PCC3 */
+#define IMX8ULP_CLK_WDOG3		0
+#define IMX8ULP_CLK_WDOG4		1
+#define IMX8ULP_CLK_LPIT1		2
+#define IMX8ULP_CLK_TPM4		3
+#define IMX8ULP_CLK_TPM5		4
+#define IMX8ULP_CLK_FLEXIO1		5
+#define IMX8ULP_CLK_I3C2		6
+#define IMX8ULP_CLK_LPI2C4		7
+#define IMX8ULP_CLK_LPI2C5		8
+#define IMX8ULP_CLK_LPUART4		9
+#define IMX8ULP_CLK_LPUART5		10
+#define IMX8ULP_CLK_LPSPI4		11
+#define IMX8ULP_CLK_LPSPI5		12
+#define IMX8ULP_CLK_DMA1_MP		13
+#define IMX8ULP_CLK_DMA1_CH0		14
+#define IMX8ULP_CLK_DMA1_CH1		15
+#define IMX8ULP_CLK_DMA1_CH2		16
+#define IMX8ULP_CLK_DMA1_CH3		17
+#define IMX8ULP_CLK_DMA1_CH4		18
+#define IMX8ULP_CLK_DMA1_CH5		19
+#define IMX8ULP_CLK_DMA1_CH6		20
+#define IMX8ULP_CLK_DMA1_CH7		21
+#define IMX8ULP_CLK_DMA1_CH8		22
+#define IMX8ULP_CLK_DMA1_CH9		23
+#define IMX8ULP_CLK_DMA1_CH10		24
+#define IMX8ULP_CLK_DMA1_CH11		25
+#define IMX8ULP_CLK_DMA1_CH12		26
+#define IMX8ULP_CLK_DMA1_CH13		27
+#define IMX8ULP_CLK_DMA1_CH14		28
+#define IMX8ULP_CLK_DMA1_CH15		29
+#define IMX8ULP_CLK_DMA1_CH16		30
+#define IMX8ULP_CLK_DMA1_CH17		31
+#define IMX8ULP_CLK_DMA1_CH18		32
+#define IMX8ULP_CLK_DMA1_CH19		33
+#define IMX8ULP_CLK_DMA1_CH20		34
+#define IMX8ULP_CLK_DMA1_CH21		35
+#define IMX8ULP_CLK_DMA1_CH22		36
+#define IMX8ULP_CLK_DMA1_CH23		37
+#define IMX8ULP_CLK_DMA1_CH24		38
+#define IMX8ULP_CLK_DMA1_CH25		39
+#define IMX8ULP_CLK_DMA1_CH26		40
+#define IMX8ULP_CLK_DMA1_CH27		41
+#define IMX8ULP_CLK_DMA1_CH28		42
+#define IMX8ULP_CLK_DMA1_CH29		43
+#define IMX8ULP_CLK_DMA1_CH30		44
+#define IMX8ULP_CLK_DMA1_CH31		45
+#define IMX8ULP_CLK_MU3_A		46
+#define IMX8ULP_CLK_MU0_B		47
+
+#define IMX8ULP_CLK_PCC3_END		48
+
+/* PCC4 */
+#define IMX8ULP_CLK_FLEXSPI2		0
+#define IMX8ULP_CLK_TPM6		1
+#define IMX8ULP_CLK_TPM7		2
+#define IMX8ULP_CLK_LPI2C6		3
+#define IMX8ULP_CLK_LPI2C7		4
+#define IMX8ULP_CLK_LPUART6		5
+#define IMX8ULP_CLK_LPUART7		6
+#define IMX8ULP_CLK_SAI4		7
+#define IMX8ULP_CLK_SAI5		8
+#define IMX8ULP_CLK_PCTLE		9
+#define IMX8ULP_CLK_PCTLF		10
+#define IMX8ULP_CLK_USDHC0		11
+#define IMX8ULP_CLK_USDHC1		12
+#define IMX8ULP_CLK_USDHC2		13
+#define IMX8ULP_CLK_USB0		14
+#define IMX8ULP_CLK_USB0_PHY		15
+#define IMX8ULP_CLK_USB1		16
+#define IMX8ULP_CLK_USB1_PHY		17
+#define IMX8ULP_CLK_USB_XBAR		18
+#define IMX8ULP_CLK_ENET		19
+#define IMX8ULP_CLK_SFA1		20
+#define IMX8ULP_CLK_RGPIOE		21
+#define IMX8ULP_CLK_RGPIOF		22
+
+#define IMX8ULP_CLK_PCC4_END		23
+
+/* PCC5 */
+#define IMX8ULP_CLK_TPM8		0
+#define IMX8ULP_CLK_SAI6		1
+#define IMX8ULP_CLK_SAI7		2
+#define IMX8ULP_CLK_SPDIF		3
+#define IMX8ULP_CLK_ISI			4
+#define IMX8ULP_CLK_CSI_REGS 		5
+#define IMX8ULP_CLK_PCTLD		6
+#define IMX8ULP_CLK_CSI			7
+#define IMX8ULP_CLK_DSI			8
+#define IMX8ULP_CLK_WDOG5		9
+#define IMX8ULP_CLK_EPDC		10
+#define IMX8ULP_CLK_PXP			11
+#define IMX8ULP_CLK_SFA2		12
+#define IMX8ULP_CLK_GPU2D		13
+#define IMX8ULP_CLK_GPU3D		14
+#define IMX8ULP_CLK_DC_NANO		15
+#define IMX8ULP_CLK_CSI_CLK_UI 		16
+#define IMX8ULP_CLK_CSI_CLK_ESC		17
+#define IMX8ULP_CLK_RGPIOD		18
+#define IMX8ULP_CLK_DMA2_MP		19
+#define IMX8ULP_CLK_DMA2_CH0		20
+#define IMX8ULP_CLK_DMA2_CH1		21
+#define IMX8ULP_CLK_DMA2_CH2		22
+#define IMX8ULP_CLK_DMA2_CH3		23
+#define IMX8ULP_CLK_DMA2_CH4		24
+#define IMX8ULP_CLK_DMA2_CH5		25
+#define IMX8ULP_CLK_DMA2_CH6		26
+#define IMX8ULP_CLK_DMA2_CH7		27
+#define IMX8ULP_CLK_DMA2_CH8		28
+#define IMX8ULP_CLK_DMA2_CH9		29
+#define IMX8ULP_CLK_DMA2_CH10		30
+#define IMX8ULP_CLK_DMA2_CH11		31
+#define IMX8ULP_CLK_DMA2_CH12		32
+#define IMX8ULP_CLK_DMA2_CH13		33
+#define IMX8ULP_CLK_DMA2_CH14		34
+#define IMX8ULP_CLK_DMA2_CH15		35
+#define IMX8ULP_CLK_DMA2_CH16		36
+#define IMX8ULP_CLK_DMA2_CH17		37
+#define IMX8ULP_CLK_DMA2_CH18		38
+#define IMX8ULP_CLK_DMA2_CH19		39
+#define IMX8ULP_CLK_DMA2_CH20		40
+#define IMX8ULP_CLK_DMA2_CH21		41
+#define IMX8ULP_CLK_DMA2_CH22		42
+#define IMX8ULP_CLK_DMA2_CH23		43
+#define IMX8ULP_CLK_DMA2_CH24		44
+#define IMX8ULP_CLK_DMA2_CH25		45
+#define IMX8ULP_CLK_DMA2_CH26		46
+#define IMX8ULP_CLK_DMA2_CH27		47
+#define IMX8ULP_CLK_DMA2_CH28		48
+#define IMX8ULP_CLK_DMA2_CH29		49
+#define IMX8ULP_CLK_DMA2_CH30		50
+#define IMX8ULP_CLK_DMA2_CH31		51
+#define IMX8ULP_CLK_MU2_B		52
+#define IMX8ULP_CLK_MU3_B		53
+#define IMX8ULP_CLK_AVD_SIM		54
+#define IMX8ULP_CLK_DSI_TX_ESC		55
+
+#define IMX8ULP_CLK_PCC5_END		56
+
+#endif
include/dt-bindings/reset/imx8ulp-pcc-reset.h new file +59 -0
new file mode 100644
index 000000000000..e99a4735c3c4
@@ -0,0 +1,59 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright 2021 NXP
+ */
+
+#ifndef DT_BINDING_PCC_RESET_IMX8ULP_H
+#define DT_BINDING_PCC_RESET_IMX8ULP_H
+
+/* PCC3 */
+#define PCC3_WDOG3_SWRST	0
+#define PCC3_WDOG4_SWRST	1
+#define PCC3_LPIT1_SWRST	2
+#define PCC3_TPM4_SWRST		3
+#define PCC3_TPM5_SWRST		4
+#define PCC3_FLEXIO1_SWRST	5
+#define PCC3_I3C2_SWRST		6
+#define PCC3_LPI2C4_SWRST	7
+#define PCC3_LPI2C5_SWRST	8
+#define PCC3_LPUART4_SWRST	9
+#define PCC3_LPUART5_SWRST	10
+#define PCC3_LPSPI4_SWRST	11
+#define PCC3_LPSPI5_SWRST	12
+
+/* PCC4 */
+#define PCC4_FLEXSPI2_SWRST	0
+#define PCC4_TPM6_SWRST		1
+#define PCC4_TPM7_SWRST		2
+#define PCC4_LPI2C6_SWRST	3
+#define PCC4_LPI2C7_SWRST	4
+#define PCC4_LPUART6_SWRST	5
+#define PCC4_LPUART7_SWRST	6
+#define PCC4_SAI4_SWRST		7
+#define PCC4_SAI5_SWRST		8
+#define PCC4_USDHC0_SWRST	9
+#define PCC4_USDHC1_SWRST	10
+#define PCC4_USDHC2_SWRST	11
+#define PCC4_USB0_SWRST		12
+#define PCC4_USB0_PHY_SWRST	13
+#define PCC4_USB1_SWRST		14
+#define PCC4_USB1_PHY_SWRST	15
+#define PCC4_ENET_SWRST		16
+
+/* PCC5 */
+#define PCC5_TPM8_SWRST		0
+#define PCC5_SAI6_SWRST		1
+#define PCC5_SAI7_SWRST		2
+#define PCC5_SPDIF_SWRST	3
+#define PCC5_ISI_SWRST		4
+#define PCC5_CSI_REGS_SWRST	5
+#define PCC5_CSI_SWRST		6
+#define PCC5_DSI_SWRST		7
+#define PCC5_WDOG5_SWRST	8
+#define PCC5_EPDC_SWRST		9
+#define PCC5_PXP_SWRST		10
+#define PCC5_GPU2D_SWRST	11
+#define PCC5_GPU3D_SWRST	12
+#define PCC5_DC_NANO_SWRST	13
+
+#endif /*DT_BINDING_RESET_IMX8ULP_H */
Signature · 1 line
2.26.2
author
#3 lore raw

RE: [PATCH v3 1/9] dt-bindings: clock: Add imx8ulp clock support

Quoted 32 lines

Subject: Re: [PATCH v3 1/9] dt-bindings: clock: Add imx8ulp clock support

Quoted 13 lines · Jacky Bai

Add the clock dt-binding file for i.MX8ULP.

For pcc node, it will also be used as a reset controller, so add the '#reset-cells' property description and add the pcc reset IDs.

---
v3 changes:
- split into two binding file, one for pcc, one for cgc

v2 changes:
- removed the redundant clocks & clock-names property

Quoted 6 lines

v1 changes:
- Move this patch from dts patchset into this patchset

---
 .../bindings/clock/imx8ulp-cgc-clock.yaml     |  43 +++
 .../bindings/clock/imx8ulp-pcc-clock.yaml     |  50 ++++
 include/dt-bindings/clock/imx8ulp-clock.h     | 258

++++++++++++++++++

Quoted 9 lines
 include/dt-bindings/reset/imx8ulp-pcc-reset.h |  59 ++++
 4 files changed, 410 insertions(+)
 create mode 100644
Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml
 create mode 100644
Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml
 create mode 100644 include/dt-bindings/clock/imx8ulp-clock.h
 create mode 100644 include/dt-bindings/reset/imx8ulp-pcc-reset.h
Quoted 7 lines
Quoted 3 lines

diff --git a/Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml b/Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml

I'm not sure but I think the Documentation part is usually done in a separate patch.

The clk-imx8ulp.c file highly depends on the clock/reset index in this dt-binding patch.

BR
Jacky Bai

Quoted 443 lines
Quoted 443 lines

new file mode 100644
index 000000000000..71f7186b135b

Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml new file +44 -0
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/imx8ulp-cgc-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX8ULP Clock Generation & Control(CGC) Module Binding
+
+maintainers:
+  - Jacky Bai <[email protected]>
+
+description: |
+  On i.MX8ULP, The clock sources generation, distribution and
+management is
+  under the control of several CGCs & PCCs modules. The CGC modules
+generate
+  and distribute clocks on the device.
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx8ulp-cgc1
+      - fsl,imx8ulp-cgc2
+
+  reg:
+    maxItems: 1
+
+  '#clock-cells':
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+  # Clock Generation & Control Module node:
+  - |
+    clock-controller@292c0000 {
+        compatible = "fsl,imx8ulp-cgc1";
+        reg = <0x292c0000 0x10000>;
+        #clock-cells = <1>;
+    };

diff --git a/Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml b/Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml new file mode 100644
index 000000000000..00612725bf8b

Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml new file +52 -0
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/imx8ulp-pcc-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX8ULP Peripheral Clock Controller(PCC) Module Binding
+
+maintainers:
+  - Jacky Bai <[email protected]>
+
+description: |
+  On i.MX8ULP, The clock sources generation, distribution and
+management is
+  under the control of several CGCs & PCCs modules. The PCC modules
+control
+  software reset, clock selection, optional division and clock gating
+mode
+  for peripherals.
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx8ulp-pcc3
+      - fsl,imx8ulp-pcc4
+      - fsl,imx8ulp-pcc5
+
+  reg:
+    maxItems: 1
+
+  '#clock-cells':
+    const: 1
+
+  '#reset-cells':
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+  - '#reset-cells'
+
+additionalProperties: false
+
+examples:
+  # Peripheral Clock Control Module node:
+  - |
+    clock-controller@292d0000 {
+        compatible = "fsl,imx8ulp-pcc3";
+        reg = <0x292d0000 0x10000>;
+        #clock-cells = <1>;
+        #reset-cells = <1>;
+    };
include/dt-bindings/clock/imx8ulp-clock.h new file +258 -0
new file mode 100644
index 000000000000..953ecfe8ebcc
@@ -0,0 +1,258 @@
+/* SPDX-License-Identifier: GPL-2.0+ OR MIT */
+/*
+ * Copyright 2021 NXP
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_IMX8ULP_H #define
+__DT_BINDINGS_CLOCK_IMX8ULP_H
+
+#define IMX8ULP_CLK_DUMMY			0
+
+/* CGC1 */
+#define IMX8ULP_CLK_SPLL2			5
+#define IMX8ULP_CLK_SPLL3			6
+#define IMX8ULP_CLK_A35_SEL			7
+#define IMX8ULP_CLK_A35_DIV			8
+#define IMX8ULP_CLK_SPLL2_PRE_SEL		9
+#define IMX8ULP_CLK_SPLL3_PRE_SEL		10
+#define IMX8ULP_CLK_SPLL3_PFD0			11
+#define IMX8ULP_CLK_SPLL3_PFD1			12
+#define IMX8ULP_CLK_SPLL3_PFD2			13
+#define IMX8ULP_CLK_SPLL3_PFD3			14
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV1		15
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV2		16
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV1		17
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV2		18
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV1		19
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV2		20
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV1		21
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV2		22
+#define IMX8ULP_CLK_NIC_SEL			23
+#define IMX8ULP_CLK_NIC_AD_DIVPLAT		24
+#define IMX8ULP_CLK_NIC_PER_DIVPLAT		25
+#define IMX8ULP_CLK_XBAR_SEL			26
+#define IMX8ULP_CLK_XBAR_AD_DIVPLAT		27
+#define IMX8ULP_CLK_XBAR_DIVBUS			28
+#define IMX8ULP_CLK_XBAR_AD_SLOW		29
+#define IMX8ULP_CLK_SOSC_DIV1			30
+#define IMX8ULP_CLK_SOSC_DIV2			31
+#define IMX8ULP_CLK_SOSC_DIV3			32
+#define IMX8ULP_CLK_FROSC_DIV1			33
+#define IMX8ULP_CLK_FROSC_DIV2			34
+#define IMX8ULP_CLK_FROSC_DIV3			35
+#define IMX8ULP_CLK_SPLL3_VCODIV		36
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV1_GATE	37
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV2_GATE	38
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV1_GATE	39
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV2_GATE	40
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV1_GATE	41
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV2_GATE	42
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV1_GATE	43
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV2_GATE	44
+#define IMX8ULP_CLK_SOSC_DIV1_GATE		45
+#define IMX8ULP_CLK_SOSC_DIV2_GATE		46
+#define IMX8ULP_CLK_SOSC_DIV3_GATE		47
+#define IMX8ULP_CLK_FROSC_DIV1_GATE		48
+#define IMX8ULP_CLK_FROSC_DIV2_GATE		49
+#define IMX8ULP_CLK_FROSC_DIV3_GATE		50
+#define IMX8ULP_CLK_SAI4_SEL			51
+#define IMX8ULP_CLK_SAI5_SEL			52
+#define IMX8ULP_CLK_AUD_CLK1			53
+#define IMX8ULP_CLK_ARM				54
+#define IMX8ULP_CLK_ENET_TS_SEL			55
+
+#define IMX8ULP_CLK_CGC1_END			56
+
+/* CGC2 */
+#define IMX8ULP_CLK_PLL4_PRE_SEL	0
+#define IMX8ULP_CLK_PLL4		1
+#define IMX8ULP_CLK_PLL4_VCODIV		2
+#define IMX8ULP_CLK_DDR_SEL		3
+#define IMX8ULP_CLK_DDR_DIV		4
+#define IMX8ULP_CLK_LPAV_AXI_SEL	5
+#define IMX8ULP_CLK_LPAV_AXI_DIV	6
+#define IMX8ULP_CLK_LPAV_AHB_DIV	7
+#define IMX8ULP_CLK_LPAV_BUS_DIV	8
+#define IMX8ULP_CLK_PLL4_PFD0		9
+#define IMX8ULP_CLK_PLL4_PFD1		10
+#define IMX8ULP_CLK_PLL4_PFD2		11
+#define IMX8ULP_CLK_PLL4_PFD3		12
+#define IMX8ULP_CLK_PLL4_PFD0_DIV1_GATE	13
+#define IMX8ULP_CLK_PLL4_PFD0_DIV2_GATE	14
+#define IMX8ULP_CLK_PLL4_PFD1_DIV1_GATE	15
+#define IMX8ULP_CLK_PLL4_PFD1_DIV2_GATE	16
+#define IMX8ULP_CLK_PLL4_PFD2_DIV1_GATE	17
+#define IMX8ULP_CLK_PLL4_PFD2_DIV2_GATE	18
+#define IMX8ULP_CLK_PLL4_PFD3_DIV1_GATE	19
+#define IMX8ULP_CLK_PLL4_PFD3_DIV2_GATE	20
+#define IMX8ULP_CLK_PLL4_PFD0_DIV1	21
+#define IMX8ULP_CLK_PLL4_PFD0_DIV2	22
+#define IMX8ULP_CLK_PLL4_PFD1_DIV1	23
+#define IMX8ULP_CLK_PLL4_PFD1_DIV2	24
+#define IMX8ULP_CLK_PLL4_PFD2_DIV1	25
+#define IMX8ULP_CLK_PLL4_PFD2_DIV2	26
+#define IMX8ULP_CLK_PLL4_PFD3_DIV1	27
+#define IMX8ULP_CLK_PLL4_PFD3_DIV2	28
+#define IMX8ULP_CLK_CGC2_SOSC_DIV1_GATE	29
+#define IMX8ULP_CLK_CGC2_SOSC_DIV2_GATE	30
+#define IMX8ULP_CLK_CGC2_SOSC_DIV3_GATE	31
+#define IMX8ULP_CLK_CGC2_SOSC_DIV1	32
+#define IMX8ULP_CLK_CGC2_SOSC_DIV2	33
+#define IMX8ULP_CLK_CGC2_SOSC_DIV3	34
+#define IMX8ULP_CLK_CGC2_FROSC_DIV1_GATE	35
+#define IMX8ULP_CLK_CGC2_FROSC_DIV2_GATE	36
+#define IMX8ULP_CLK_CGC2_FROSC_DIV3_GATE	37
+#define IMX8ULP_CLK_CGC2_FROSC_DIV1	38
+#define IMX8ULP_CLK_CGC2_FROSC_DIV2	39
+#define IMX8ULP_CLK_CGC2_FROSC_DIV3	40
+#define IMX8ULP_CLK_AUD_CLK2		41
+#define IMX8ULP_CLK_SAI6_SEL		42
+#define IMX8ULP_CLK_SAI7_SEL		43
+#define IMX8ULP_CLK_SPDIF_SEL		44
+#define IMX8ULP_CLK_HIFI_SEL		45
+#define IMX8ULP_CLK_HIFI_DIVCORE	46
+#define IMX8ULP_CLK_HIFI_DIVPLAT	47
+#define IMX8ULP_CLK_DSI_PHY_REF		48
+
+#define IMX8ULP_CLK_CGC2_END		49
+
+/* PCC3 */
+#define IMX8ULP_CLK_WDOG3		0
+#define IMX8ULP_CLK_WDOG4		1
+#define IMX8ULP_CLK_LPIT1		2
+#define IMX8ULP_CLK_TPM4		3
+#define IMX8ULP_CLK_TPM5		4
+#define IMX8ULP_CLK_FLEXIO1		5
+#define IMX8ULP_CLK_I3C2		6
+#define IMX8ULP_CLK_LPI2C4		7
+#define IMX8ULP_CLK_LPI2C5		8
+#define IMX8ULP_CLK_LPUART4		9
+#define IMX8ULP_CLK_LPUART5		10
+#define IMX8ULP_CLK_LPSPI4		11
+#define IMX8ULP_CLK_LPSPI5		12
+#define IMX8ULP_CLK_DMA1_MP		13
+#define IMX8ULP_CLK_DMA1_CH0		14
+#define IMX8ULP_CLK_DMA1_CH1		15
+#define IMX8ULP_CLK_DMA1_CH2		16
+#define IMX8ULP_CLK_DMA1_CH3		17
+#define IMX8ULP_CLK_DMA1_CH4		18
+#define IMX8ULP_CLK_DMA1_CH5		19
+#define IMX8ULP_CLK_DMA1_CH6		20
+#define IMX8ULP_CLK_DMA1_CH7		21
+#define IMX8ULP_CLK_DMA1_CH8		22
+#define IMX8ULP_CLK_DMA1_CH9		23
+#define IMX8ULP_CLK_DMA1_CH10		24
+#define IMX8ULP_CLK_DMA1_CH11		25
+#define IMX8ULP_CLK_DMA1_CH12		26
+#define IMX8ULP_CLK_DMA1_CH13		27
+#define IMX8ULP_CLK_DMA1_CH14		28
+#define IMX8ULP_CLK_DMA1_CH15		29
+#define IMX8ULP_CLK_DMA1_CH16		30
+#define IMX8ULP_CLK_DMA1_CH17		31
+#define IMX8ULP_CLK_DMA1_CH18		32
+#define IMX8ULP_CLK_DMA1_CH19		33
+#define IMX8ULP_CLK_DMA1_CH20		34
+#define IMX8ULP_CLK_DMA1_CH21		35
+#define IMX8ULP_CLK_DMA1_CH22		36
+#define IMX8ULP_CLK_DMA1_CH23		37
+#define IMX8ULP_CLK_DMA1_CH24		38
+#define IMX8ULP_CLK_DMA1_CH25		39
+#define IMX8ULP_CLK_DMA1_CH26		40
+#define IMX8ULP_CLK_DMA1_CH27		41
+#define IMX8ULP_CLK_DMA1_CH28		42
+#define IMX8ULP_CLK_DMA1_CH29		43
+#define IMX8ULP_CLK_DMA1_CH30		44
+#define IMX8ULP_CLK_DMA1_CH31		45
+#define IMX8ULP_CLK_MU3_A		46
+#define IMX8ULP_CLK_MU0_B		47
+
+#define IMX8ULP_CLK_PCC3_END		48
+
+/* PCC4 */
+#define IMX8ULP_CLK_FLEXSPI2		0
+#define IMX8ULP_CLK_TPM6		1
+#define IMX8ULP_CLK_TPM7		2
+#define IMX8ULP_CLK_LPI2C6		3
+#define IMX8ULP_CLK_LPI2C7		4
+#define IMX8ULP_CLK_LPUART6		5
+#define IMX8ULP_CLK_LPUART7		6
+#define IMX8ULP_CLK_SAI4		7
+#define IMX8ULP_CLK_SAI5		8
+#define IMX8ULP_CLK_PCTLE		9
+#define IMX8ULP_CLK_PCTLF		10
+#define IMX8ULP_CLK_USDHC0		11
+#define IMX8ULP_CLK_USDHC1		12
+#define IMX8ULP_CLK_USDHC2		13
+#define IMX8ULP_CLK_USB0		14
+#define IMX8ULP_CLK_USB0_PHY		15
+#define IMX8ULP_CLK_USB1		16
+#define IMX8ULP_CLK_USB1_PHY		17
+#define IMX8ULP_CLK_USB_XBAR		18
+#define IMX8ULP_CLK_ENET		19
+#define IMX8ULP_CLK_SFA1		20
+#define IMX8ULP_CLK_RGPIOE		21
+#define IMX8ULP_CLK_RGPIOF		22
+
+#define IMX8ULP_CLK_PCC4_END		23
+
+/* PCC5 */
+#define IMX8ULP_CLK_TPM8		0
+#define IMX8ULP_CLK_SAI6		1
+#define IMX8ULP_CLK_SAI7		2
+#define IMX8ULP_CLK_SPDIF		3
+#define IMX8ULP_CLK_ISI			4
+#define IMX8ULP_CLK_CSI_REGS 		5
+#define IMX8ULP_CLK_PCTLD		6
+#define IMX8ULP_CLK_CSI			7
+#define IMX8ULP_CLK_DSI			8
+#define IMX8ULP_CLK_WDOG5		9
+#define IMX8ULP_CLK_EPDC		10
+#define IMX8ULP_CLK_PXP			11
+#define IMX8ULP_CLK_SFA2		12
+#define IMX8ULP_CLK_GPU2D		13
+#define IMX8ULP_CLK_GPU3D		14
+#define IMX8ULP_CLK_DC_NANO		15
+#define IMX8ULP_CLK_CSI_CLK_UI 		16
+#define IMX8ULP_CLK_CSI_CLK_ESC		17
+#define IMX8ULP_CLK_RGPIOD		18
+#define IMX8ULP_CLK_DMA2_MP		19
+#define IMX8ULP_CLK_DMA2_CH0		20
+#define IMX8ULP_CLK_DMA2_CH1		21
+#define IMX8ULP_CLK_DMA2_CH2		22
+#define IMX8ULP_CLK_DMA2_CH3		23
+#define IMX8ULP_CLK_DMA2_CH4		24
+#define IMX8ULP_CLK_DMA2_CH5		25
+#define IMX8ULP_CLK_DMA2_CH6		26
+#define IMX8ULP_CLK_DMA2_CH7		27
+#define IMX8ULP_CLK_DMA2_CH8		28
+#define IMX8ULP_CLK_DMA2_CH9		29
+#define IMX8ULP_CLK_DMA2_CH10		30
+#define IMX8ULP_CLK_DMA2_CH11		31
+#define IMX8ULP_CLK_DMA2_CH12		32
+#define IMX8ULP_CLK_DMA2_CH13		33
+#define IMX8ULP_CLK_DMA2_CH14		34
+#define IMX8ULP_CLK_DMA2_CH15		35
+#define IMX8ULP_CLK_DMA2_CH16		36
+#define IMX8ULP_CLK_DMA2_CH17		37
+#define IMX8ULP_CLK_DMA2_CH18		38
+#define IMX8ULP_CLK_DMA2_CH19		39
+#define IMX8ULP_CLK_DMA2_CH20		40
+#define IMX8ULP_CLK_DMA2_CH21		41
+#define IMX8ULP_CLK_DMA2_CH22		42
+#define IMX8ULP_CLK_DMA2_CH23		43
+#define IMX8ULP_CLK_DMA2_CH24		44
+#define IMX8ULP_CLK_DMA2_CH25		45
+#define IMX8ULP_CLK_DMA2_CH26		46
+#define IMX8ULP_CLK_DMA2_CH27		47
+#define IMX8ULP_CLK_DMA2_CH28		48
+#define IMX8ULP_CLK_DMA2_CH29		49
+#define IMX8ULP_CLK_DMA2_CH30		50
+#define IMX8ULP_CLK_DMA2_CH31		51
+#define IMX8ULP_CLK_MU2_B		52
+#define IMX8ULP_CLK_MU3_B		53
+#define IMX8ULP_CLK_AVD_SIM		54
+#define IMX8ULP_CLK_DSI_TX_ESC		55
+
+#define IMX8ULP_CLK_PCC5_END		56
+
+#endif
include/dt-bindings/reset/imx8ulp-pcc-reset.h new file +59 -1
new file mode 100644
index 000000000000..e99a4735c3c4
@@ -0,0 +1,59 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright 2021 NXP
+ */
+
+#ifndef DT_BINDING_PCC_RESET_IMX8ULP_H #define
+DT_BINDING_PCC_RESET_IMX8ULP_H
+
+/* PCC3 */
+#define PCC3_WDOG3_SWRST	0
+#define PCC3_WDOG4_SWRST	1
+#define PCC3_LPIT1_SWRST	2
+#define PCC3_TPM4_SWRST		3
+#define PCC3_TPM5_SWRST		4
+#define PCC3_FLEXIO1_SWRST	5
+#define PCC3_I3C2_SWRST		6
+#define PCC3_LPI2C4_SWRST	7
+#define PCC3_LPI2C5_SWRST	8
+#define PCC3_LPUART4_SWRST	9
+#define PCC3_LPUART5_SWRST	10
+#define PCC3_LPSPI4_SWRST	11
+#define PCC3_LPSPI5_SWRST	12
+
+/* PCC4 */
+#define PCC4_FLEXSPI2_SWRST	0
+#define PCC4_TPM6_SWRST		1
+#define PCC4_TPM7_SWRST		2
+#define PCC4_LPI2C6_SWRST	3
+#define PCC4_LPI2C7_SWRST	4
+#define PCC4_LPUART6_SWRST	5
+#define PCC4_LPUART7_SWRST	6
+#define PCC4_SAI4_SWRST		7
+#define PCC4_SAI5_SWRST		8
+#define PCC4_USDHC0_SWRST	9
+#define PCC4_USDHC1_SWRST	10
+#define PCC4_USDHC2_SWRST	11
+#define PCC4_USB0_SWRST		12
+#define PCC4_USB0_PHY_SWRST	13
+#define PCC4_USB1_SWRST		14
+#define PCC4_USB1_PHY_SWRST	15
+#define PCC4_ENET_SWRST		16
+
+/* PCC5 */
+#define PCC5_TPM8_SWRST		0
+#define PCC5_SAI6_SWRST		1
+#define PCC5_SAI7_SWRST		2
+#define PCC5_SPDIF_SWRST	3
+#define PCC5_ISI_SWRST		4
+#define PCC5_CSI_REGS_SWRST	5
+#define PCC5_CSI_SWRST		6
+#define PCC5_DSI_SWRST		7
+#define PCC5_WDOG5_SWRST	8
+#define PCC5_EPDC_SWRST		9
+#define PCC5_PXP_SWRST		10
+#define PCC5_GPU2D_SWRST	11
+#define PCC5_GPU3D_SWRST	12
+#define PCC5_DC_NANO_SWRST	13
+
+#endif /*DT_BINDING_RESET_IMX8ULP_H */
--

2.26.2

Reviewed-by
#4 lore raw

Re: [PATCH v3 1/9] dt-bindings: clock: Add imx8ulp clock support

Quoted 36 lines · Jacky Bai
Quoted 36 lines

Subject: Re: [PATCH v3 1/9] dt-bindings: clock: Add imx8ulp clock support

Quoted 13 lines · Jacky Bai

Add the clock dt-binding file for i.MX8ULP.

For pcc node, it will also be used as a reset controller, so add the '#reset-cells' property description and add the pcc reset IDs.

---
v3 changes:
- split into two binding file, one for pcc, one for cgc

v2 changes:
- removed the redundant clocks & clock-names property

Quoted 6 lines

v1 changes:
- Move this patch from dts patchset into this patchset

---
 .../bindings/clock/imx8ulp-cgc-clock.yaml     |  43 +++
 .../bindings/clock/imx8ulp-pcc-clock.yaml     |  50 ++++
 include/dt-bindings/clock/imx8ulp-clock.h     | 258

++++++++++++++++++

Quoted 12 lines
 include/dt-bindings/reset/imx8ulp-pcc-reset.h |  59 ++++
 4 files changed, 410 insertions(+)
 create mode 100644
Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml
 create mode 100644
Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml
 create mode 100644 include/dt-bindings/clock/imx8ulp-clock.h
 create mode 100644 include/dt-bindings/reset/imx8ulp-pcc-reset.h

diff --git a/Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml b/Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml

Quoted 6 lines
Quoted 3 lines

I'm not sure but I think the Documentation part is usually done in a separate patch.

The clk-imx8ulp.c file highly depends on the clock/reset index in this dt-binding patch.

Yeah, I get that, but I was suggesting splitting the Documentation part and the binding header part into two separate patches. It's up to you.

For everything else:

Quoted 446 lines

BR
Jacky Bai

Quoted 443 lines
Quoted 443 lines

new file mode 100644
index 000000000000..71f7186b135b

Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml new file +44 -0
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/imx8ulp-cgc-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX8ULP Clock Generation & Control(CGC) Module Binding
+
+maintainers:
+  - Jacky Bai <[email protected]>
+
+description: |
+  On i.MX8ULP, The clock sources generation, distribution and
+management is
+  under the control of several CGCs & PCCs modules. The CGC modules
+generate
+  and distribute clocks on the device.
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx8ulp-cgc1
+      - fsl,imx8ulp-cgc2
+
+  reg:
+    maxItems: 1
+
+  '#clock-cells':
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+  # Clock Generation & Control Module node:
+  - |
+    clock-controller@292c0000 {
+        compatible = "fsl,imx8ulp-cgc1";
+        reg = <0x292c0000 0x10000>;
+        #clock-cells = <1>;
+    };

diff --git a/Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml b/Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml new file mode 100644
index 000000000000..00612725bf8b

Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml new file +52 -0
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/imx8ulp-pcc-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX8ULP Peripheral Clock Controller(PCC) Module Binding
+
+maintainers:
+  - Jacky Bai <[email protected]>
+
+description: |
+  On i.MX8ULP, The clock sources generation, distribution and
+management is
+  under the control of several CGCs & PCCs modules. The PCC modules
+control
+  software reset, clock selection, optional division and clock gating
+mode
+  for peripherals.
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx8ulp-pcc3
+      - fsl,imx8ulp-pcc4
+      - fsl,imx8ulp-pcc5
+
+  reg:
+    maxItems: 1
+
+  '#clock-cells':
+    const: 1
+
+  '#reset-cells':
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+  - '#reset-cells'
+
+additionalProperties: false
+
+examples:
+  # Peripheral Clock Control Module node:
+  - |
+    clock-controller@292d0000 {
+        compatible = "fsl,imx8ulp-pcc3";
+        reg = <0x292d0000 0x10000>;
+        #clock-cells = <1>;
+        #reset-cells = <1>;
+    };
include/dt-bindings/clock/imx8ulp-clock.h new file +258 -0
new file mode 100644
index 000000000000..953ecfe8ebcc
@@ -0,0 +1,258 @@
+/* SPDX-License-Identifier: GPL-2.0+ OR MIT */
+/*
+ * Copyright 2021 NXP
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_IMX8ULP_H #define
+__DT_BINDINGS_CLOCK_IMX8ULP_H
+
+#define IMX8ULP_CLK_DUMMY			0
+
+/* CGC1 */
+#define IMX8ULP_CLK_SPLL2			5
+#define IMX8ULP_CLK_SPLL3			6
+#define IMX8ULP_CLK_A35_SEL			7
+#define IMX8ULP_CLK_A35_DIV			8
+#define IMX8ULP_CLK_SPLL2_PRE_SEL		9
+#define IMX8ULP_CLK_SPLL3_PRE_SEL		10
+#define IMX8ULP_CLK_SPLL3_PFD0			11
+#define IMX8ULP_CLK_SPLL3_PFD1			12
+#define IMX8ULP_CLK_SPLL3_PFD2			13
+#define IMX8ULP_CLK_SPLL3_PFD3			14
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV1		15
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV2		16
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV1		17
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV2		18
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV1		19
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV2		20
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV1		21
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV2		22
+#define IMX8ULP_CLK_NIC_SEL			23
+#define IMX8ULP_CLK_NIC_AD_DIVPLAT		24
+#define IMX8ULP_CLK_NIC_PER_DIVPLAT		25
+#define IMX8ULP_CLK_XBAR_SEL			26
+#define IMX8ULP_CLK_XBAR_AD_DIVPLAT		27
+#define IMX8ULP_CLK_XBAR_DIVBUS			28
+#define IMX8ULP_CLK_XBAR_AD_SLOW		29
+#define IMX8ULP_CLK_SOSC_DIV1			30
+#define IMX8ULP_CLK_SOSC_DIV2			31
+#define IMX8ULP_CLK_SOSC_DIV3			32
+#define IMX8ULP_CLK_FROSC_DIV1			33
+#define IMX8ULP_CLK_FROSC_DIV2			34
+#define IMX8ULP_CLK_FROSC_DIV3			35
+#define IMX8ULP_CLK_SPLL3_VCODIV		36
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV1_GATE	37
+#define IMX8ULP_CLK_SPLL3_PFD0_DIV2_GATE	38
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV1_GATE	39
+#define IMX8ULP_CLK_SPLL3_PFD1_DIV2_GATE	40
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV1_GATE	41
+#define IMX8ULP_CLK_SPLL3_PFD2_DIV2_GATE	42
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV1_GATE	43
+#define IMX8ULP_CLK_SPLL3_PFD3_DIV2_GATE	44
+#define IMX8ULP_CLK_SOSC_DIV1_GATE		45
+#define IMX8ULP_CLK_SOSC_DIV2_GATE		46
+#define IMX8ULP_CLK_SOSC_DIV3_GATE		47
+#define IMX8ULP_CLK_FROSC_DIV1_GATE		48
+#define IMX8ULP_CLK_FROSC_DIV2_GATE		49
+#define IMX8ULP_CLK_FROSC_DIV3_GATE		50
+#define IMX8ULP_CLK_SAI4_SEL			51
+#define IMX8ULP_CLK_SAI5_SEL			52
+#define IMX8ULP_CLK_AUD_CLK1			53
+#define IMX8ULP_CLK_ARM				54
+#define IMX8ULP_CLK_ENET_TS_SEL			55
+
+#define IMX8ULP_CLK_CGC1_END			56
+
+/* CGC2 */
+#define IMX8ULP_CLK_PLL4_PRE_SEL	0
+#define IMX8ULP_CLK_PLL4		1
+#define IMX8ULP_CLK_PLL4_VCODIV		2
+#define IMX8ULP_CLK_DDR_SEL		3
+#define IMX8ULP_CLK_DDR_DIV		4
+#define IMX8ULP_CLK_LPAV_AXI_SEL	5
+#define IMX8ULP_CLK_LPAV_AXI_DIV	6
+#define IMX8ULP_CLK_LPAV_AHB_DIV	7
+#define IMX8ULP_CLK_LPAV_BUS_DIV	8
+#define IMX8ULP_CLK_PLL4_PFD0		9
+#define IMX8ULP_CLK_PLL4_PFD1		10
+#define IMX8ULP_CLK_PLL4_PFD2		11
+#define IMX8ULP_CLK_PLL4_PFD3		12
+#define IMX8ULP_CLK_PLL4_PFD0_DIV1_GATE	13
+#define IMX8ULP_CLK_PLL4_PFD0_DIV2_GATE	14
+#define IMX8ULP_CLK_PLL4_PFD1_DIV1_GATE	15
+#define IMX8ULP_CLK_PLL4_PFD1_DIV2_GATE	16
+#define IMX8ULP_CLK_PLL4_PFD2_DIV1_GATE	17
+#define IMX8ULP_CLK_PLL4_PFD2_DIV2_GATE	18
+#define IMX8ULP_CLK_PLL4_PFD3_DIV1_GATE	19
+#define IMX8ULP_CLK_PLL4_PFD3_DIV2_GATE	20
+#define IMX8ULP_CLK_PLL4_PFD0_DIV1	21
+#define IMX8ULP_CLK_PLL4_PFD0_DIV2	22
+#define IMX8ULP_CLK_PLL4_PFD1_DIV1	23
+#define IMX8ULP_CLK_PLL4_PFD1_DIV2	24
+#define IMX8ULP_CLK_PLL4_PFD2_DIV1	25
+#define IMX8ULP_CLK_PLL4_PFD2_DIV2	26
+#define IMX8ULP_CLK_PLL4_PFD3_DIV1	27
+#define IMX8ULP_CLK_PLL4_PFD3_DIV2	28
+#define IMX8ULP_CLK_CGC2_SOSC_DIV1_GATE	29
+#define IMX8ULP_CLK_CGC2_SOSC_DIV2_GATE	30
+#define IMX8ULP_CLK_CGC2_SOSC_DIV3_GATE	31
+#define IMX8ULP_CLK_CGC2_SOSC_DIV1	32
+#define IMX8ULP_CLK_CGC2_SOSC_DIV2	33
+#define IMX8ULP_CLK_CGC2_SOSC_DIV3	34
+#define IMX8ULP_CLK_CGC2_FROSC_DIV1_GATE	35
+#define IMX8ULP_CLK_CGC2_FROSC_DIV2_GATE	36
+#define IMX8ULP_CLK_CGC2_FROSC_DIV3_GATE	37
+#define IMX8ULP_CLK_CGC2_FROSC_DIV1	38
+#define IMX8ULP_CLK_CGC2_FROSC_DIV2	39
+#define IMX8ULP_CLK_CGC2_FROSC_DIV3	40
+#define IMX8ULP_CLK_AUD_CLK2		41
+#define IMX8ULP_CLK_SAI6_SEL		42
+#define IMX8ULP_CLK_SAI7_SEL		43
+#define IMX8ULP_CLK_SPDIF_SEL		44
+#define IMX8ULP_CLK_HIFI_SEL		45
+#define IMX8ULP_CLK_HIFI_DIVCORE	46
+#define IMX8ULP_CLK_HIFI_DIVPLAT	47
+#define IMX8ULP_CLK_DSI_PHY_REF		48
+
+#define IMX8ULP_CLK_CGC2_END		49
+
+/* PCC3 */
+#define IMX8ULP_CLK_WDOG3		0
+#define IMX8ULP_CLK_WDOG4		1
+#define IMX8ULP_CLK_LPIT1		2
+#define IMX8ULP_CLK_TPM4		3
+#define IMX8ULP_CLK_TPM5		4
+#define IMX8ULP_CLK_FLEXIO1		5
+#define IMX8ULP_CLK_I3C2		6
+#define IMX8ULP_CLK_LPI2C4		7
+#define IMX8ULP_CLK_LPI2C5		8
+#define IMX8ULP_CLK_LPUART4		9
+#define IMX8ULP_CLK_LPUART5		10
+#define IMX8ULP_CLK_LPSPI4		11
+#define IMX8ULP_CLK_LPSPI5		12
+#define IMX8ULP_CLK_DMA1_MP		13
+#define IMX8ULP_CLK_DMA1_CH0		14
+#define IMX8ULP_CLK_DMA1_CH1		15
+#define IMX8ULP_CLK_DMA1_CH2		16
+#define IMX8ULP_CLK_DMA1_CH3		17
+#define IMX8ULP_CLK_DMA1_CH4		18
+#define IMX8ULP_CLK_DMA1_CH5		19
+#define IMX8ULP_CLK_DMA1_CH6		20
+#define IMX8ULP_CLK_DMA1_CH7		21
+#define IMX8ULP_CLK_DMA1_CH8		22
+#define IMX8ULP_CLK_DMA1_CH9		23
+#define IMX8ULP_CLK_DMA1_CH10		24
+#define IMX8ULP_CLK_DMA1_CH11		25
+#define IMX8ULP_CLK_DMA1_CH12		26
+#define IMX8ULP_CLK_DMA1_CH13		27
+#define IMX8ULP_CLK_DMA1_CH14		28
+#define IMX8ULP_CLK_DMA1_CH15		29
+#define IMX8ULP_CLK_DMA1_CH16		30
+#define IMX8ULP_CLK_DMA1_CH17		31
+#define IMX8ULP_CLK_DMA1_CH18		32
+#define IMX8ULP_CLK_DMA1_CH19		33
+#define IMX8ULP_CLK_DMA1_CH20		34
+#define IMX8ULP_CLK_DMA1_CH21		35
+#define IMX8ULP_CLK_DMA1_CH22		36
+#define IMX8ULP_CLK_DMA1_CH23		37
+#define IMX8ULP_CLK_DMA1_CH24		38
+#define IMX8ULP_CLK_DMA1_CH25		39
+#define IMX8ULP_CLK_DMA1_CH26		40
+#define IMX8ULP_CLK_DMA1_CH27		41
+#define IMX8ULP_CLK_DMA1_CH28		42
+#define IMX8ULP_CLK_DMA1_CH29		43
+#define IMX8ULP_CLK_DMA1_CH30		44
+#define IMX8ULP_CLK_DMA1_CH31		45
+#define IMX8ULP_CLK_MU3_A		46
+#define IMX8ULP_CLK_MU0_B		47
+
+#define IMX8ULP_CLK_PCC3_END		48
+
+/* PCC4 */
+#define IMX8ULP_CLK_FLEXSPI2		0
+#define IMX8ULP_CLK_TPM6		1
+#define IMX8ULP_CLK_TPM7		2
+#define IMX8ULP_CLK_LPI2C6		3
+#define IMX8ULP_CLK_LPI2C7		4
+#define IMX8ULP_CLK_LPUART6		5
+#define IMX8ULP_CLK_LPUART7		6
+#define IMX8ULP_CLK_SAI4		7
+#define IMX8ULP_CLK_SAI5		8
+#define IMX8ULP_CLK_PCTLE		9
+#define IMX8ULP_CLK_PCTLF		10
+#define IMX8ULP_CLK_USDHC0		11
+#define IMX8ULP_CLK_USDHC1		12
+#define IMX8ULP_CLK_USDHC2		13
+#define IMX8ULP_CLK_USB0		14
+#define IMX8ULP_CLK_USB0_PHY		15
+#define IMX8ULP_CLK_USB1		16
+#define IMX8ULP_CLK_USB1_PHY		17
+#define IMX8ULP_CLK_USB_XBAR		18
+#define IMX8ULP_CLK_ENET		19
+#define IMX8ULP_CLK_SFA1		20
+#define IMX8ULP_CLK_RGPIOE		21
+#define IMX8ULP_CLK_RGPIOF		22
+
+#define IMX8ULP_CLK_PCC4_END		23
+
+/* PCC5 */
+#define IMX8ULP_CLK_TPM8		0
+#define IMX8ULP_CLK_SAI6		1
+#define IMX8ULP_CLK_SAI7		2
+#define IMX8ULP_CLK_SPDIF		3
+#define IMX8ULP_CLK_ISI			4
+#define IMX8ULP_CLK_CSI_REGS 		5
+#define IMX8ULP_CLK_PCTLD		6
+#define IMX8ULP_CLK_CSI			7
+#define IMX8ULP_CLK_DSI			8
+#define IMX8ULP_CLK_WDOG5		9
+#define IMX8ULP_CLK_EPDC		10
+#define IMX8ULP_CLK_PXP			11
+#define IMX8ULP_CLK_SFA2		12
+#define IMX8ULP_CLK_GPU2D		13
+#define IMX8ULP_CLK_GPU3D		14
+#define IMX8ULP_CLK_DC_NANO		15
+#define IMX8ULP_CLK_CSI_CLK_UI 		16
+#define IMX8ULP_CLK_CSI_CLK_ESC		17
+#define IMX8ULP_CLK_RGPIOD		18
+#define IMX8ULP_CLK_DMA2_MP		19
+#define IMX8ULP_CLK_DMA2_CH0		20
+#define IMX8ULP_CLK_DMA2_CH1		21
+#define IMX8ULP_CLK_DMA2_CH2		22
+#define IMX8ULP_CLK_DMA2_CH3		23
+#define IMX8ULP_CLK_DMA2_CH4		24
+#define IMX8ULP_CLK_DMA2_CH5		25
+#define IMX8ULP_CLK_DMA2_CH6		26
+#define IMX8ULP_CLK_DMA2_CH7		27
+#define IMX8ULP_CLK_DMA2_CH8		28
+#define IMX8ULP_CLK_DMA2_CH9		29
+#define IMX8ULP_CLK_DMA2_CH10		30
+#define IMX8ULP_CLK_DMA2_CH11		31
+#define IMX8ULP_CLK_DMA2_CH12		32
+#define IMX8ULP_CLK_DMA2_CH13		33
+#define IMX8ULP_CLK_DMA2_CH14		34
+#define IMX8ULP_CLK_DMA2_CH15		35
+#define IMX8ULP_CLK_DMA2_CH16		36
+#define IMX8ULP_CLK_DMA2_CH17		37
+#define IMX8ULP_CLK_DMA2_CH18		38
+#define IMX8ULP_CLK_DMA2_CH19		39
+#define IMX8ULP_CLK_DMA2_CH20		40
+#define IMX8ULP_CLK_DMA2_CH21		41
+#define IMX8ULP_CLK_DMA2_CH22		42
+#define IMX8ULP_CLK_DMA2_CH23		43
+#define IMX8ULP_CLK_DMA2_CH24		44
+#define IMX8ULP_CLK_DMA2_CH25		45
+#define IMX8ULP_CLK_DMA2_CH26		46
+#define IMX8ULP_CLK_DMA2_CH27		47
+#define IMX8ULP_CLK_DMA2_CH28		48
+#define IMX8ULP_CLK_DMA2_CH29		49
+#define IMX8ULP_CLK_DMA2_CH30		50
+#define IMX8ULP_CLK_DMA2_CH31		51
+#define IMX8ULP_CLK_MU2_B		52
+#define IMX8ULP_CLK_MU3_B		53
+#define IMX8ULP_CLK_AVD_SIM		54
+#define IMX8ULP_CLK_DSI_TX_ESC		55
+
+#define IMX8ULP_CLK_PCC5_END		56
+
+#endif
include/dt-bindings/reset/imx8ulp-pcc-reset.h new file +59 -1
new file mode 100644
index 000000000000..e99a4735c3c4
@@ -0,0 +1,59 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright 2021 NXP
+ */
+
+#ifndef DT_BINDING_PCC_RESET_IMX8ULP_H #define
+DT_BINDING_PCC_RESET_IMX8ULP_H
+
+/* PCC3 */
+#define PCC3_WDOG3_SWRST	0
+#define PCC3_WDOG4_SWRST	1
+#define PCC3_LPIT1_SWRST	2
+#define PCC3_TPM4_SWRST		3
+#define PCC3_TPM5_SWRST		4
+#define PCC3_FLEXIO1_SWRST	5
+#define PCC3_I3C2_SWRST		6
+#define PCC3_LPI2C4_SWRST	7
+#define PCC3_LPI2C5_SWRST	8
+#define PCC3_LPUART4_SWRST	9
+#define PCC3_LPUART5_SWRST	10
+#define PCC3_LPSPI4_SWRST	11
+#define PCC3_LPSPI5_SWRST	12
+
+/* PCC4 */
+#define PCC4_FLEXSPI2_SWRST	0
+#define PCC4_TPM6_SWRST		1
+#define PCC4_TPM7_SWRST		2
+#define PCC4_LPI2C6_SWRST	3
+#define PCC4_LPI2C7_SWRST	4
+#define PCC4_LPUART6_SWRST	5
+#define PCC4_LPUART7_SWRST	6
+#define PCC4_SAI4_SWRST		7
+#define PCC4_SAI5_SWRST		8
+#define PCC4_USDHC0_SWRST	9
+#define PCC4_USDHC1_SWRST	10
+#define PCC4_USDHC2_SWRST	11
+#define PCC4_USB0_SWRST		12
+#define PCC4_USB0_PHY_SWRST	13
+#define PCC4_USB1_SWRST		14
+#define PCC4_USB1_PHY_SWRST	15
+#define PCC4_ENET_SWRST		16
+
+/* PCC5 */
+#define PCC5_TPM8_SWRST		0
+#define PCC5_SAI6_SWRST		1
+#define PCC5_SAI7_SWRST		2
+#define PCC5_SPDIF_SWRST	3
+#define PCC5_ISI_SWRST		4
+#define PCC5_CSI_REGS_SWRST	5
+#define PCC5_CSI_SWRST		6
+#define PCC5_DSI_SWRST		7
+#define PCC5_WDOG5_SWRST	8
+#define PCC5_EPDC_SWRST		9
+#define PCC5_PXP_SWRST		10
+#define PCC5_GPU2D_SWRST	11
+#define PCC5_GPU3D_SWRST	12
+#define PCC5_DC_NANO_SWRST	13
+
+#endif /*DT_BINDING_RESET_IMX8ULP_H */
--

2.26.2

maintainer
#5 lore raw

Re: [PATCH v3 1/9] dt-bindings: clock: Add imx8ulp clock support

Quoted 41 lines · Abel Vesa
Quoted 40 lines · Jacky Bai
Quoted 39 lines

Subject: Re: [PATCH v3 1/9] dt-bindings: clock: Add imx8ulp clock support

Quoted 13 lines · Jacky Bai

Add the clock dt-binding file for i.MX8ULP.

For pcc node, it will also be used as a reset controller, so add the '#reset-cells' property description and add the pcc reset IDs.

---
v3 changes:
- split into two binding file, one for pcc, one for cgc

v2 changes:
- removed the redundant clocks & clock-names property

Quoted 6 lines

v1 changes:
- Move this patch from dts patchset into this patchset

---
 .../bindings/clock/imx8ulp-cgc-clock.yaml     |  43 +++
 .../bindings/clock/imx8ulp-pcc-clock.yaml     |  50 ++++
 include/dt-bindings/clock/imx8ulp-clock.h     | 258

++++++++++++++++++

Quoted 9 lines
 include/dt-bindings/reset/imx8ulp-pcc-reset.h |  59 ++++
 4 files changed, 410 insertions(+)
 create mode 100644
Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml
 create mode 100644
Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml
 create mode 100644 include/dt-bindings/clock/imx8ulp-clock.h
 create mode 100644 include/dt-bindings/reset/imx8ulp-pcc-reset.h
Quoted 3 lines

diff --git a/Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml b/Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml

I'm not sure but I think the Documentation part is usually done in a separate patch.

Quoted 5 lines
Quoted 2 lines

The clk-imx8ulp.c file highly depends on the clock/reset index in this dt-binding patch.

Yeah, I get that, but I was suggesting splitting the Documentation part and the binding header part into two separate patches. It's up to you.

The header is part of the binding ABI, so it belongs in this patch.

Rob

author
#6 lore raw

PATCH v3 2/9 clk: imx: Update the pllv4 to support imx8ulp

In reply to Jacky Bai

The PLLs used on i.MX8ULP is mostly the same as on i.MX7ULP, except the PLL register offset is changed. Change the PLLv4 driver for code reuse on i.MX7ULP and i.MX8ULP.

---
v3 changes: no

---
 drivers/clk/imx/clk-imx7ulp.c |  4 ++--
 drivers/clk/imx/clk-pllv4.c   | 34 +++++++++++++++++++++++++---------
 drivers/clk/imx/clk.h         |  9 +++++++--
 3 files changed, 34 insertions(+), 13 deletions(-)
drivers/clk/imx/clk-imx7ulp.c +2 -2
index 779e09105da7..ba50d6db8097 100644
@@ -78,8 +78,8 @@ static void __init imx7ulp_clk_scg1_init(struct device_node *np)
 	hws[IMX7ULP_CLK_SPLL_PRE_DIV]	= imx_clk_hw_divider_flags("spll_pre_div", "spll_pre_sel", base + 0x608,	8,	3,	CLK_SET_RATE_GATE);
 
 	/*						name	 parent_name	 base */
-	hws[IMX7ULP_CLK_APLL]		= imx_clk_hw_pllv4("apll",  "apll_pre_div", base + 0x500);
-	hws[IMX7ULP_CLK_SPLL]		= imx_clk_hw_pllv4("spll",  "spll_pre_div", base + 0x600);
+	hws[IMX7ULP_CLK_APLL]		= imx_clk_hw_pllv4(IMX_PLLV4_IMX7ULP, "apll",  "apll_pre_div", base + 0x500);
+	hws[IMX7ULP_CLK_SPLL]		= imx_clk_hw_pllv4(IMX_PLLV4_IMX7ULP, "spll",  "spll_pre_div", base + 0x600);
 
 	/* APLL PFDs */
 	hws[IMX7ULP_CLK_APLL_PFD0]	= imx_clk_hw_pfdv2("apll_pfd0", "apll", base + 0x50c, 0);
drivers/clk/imx/clk-pllv4.c +25 -9
index 8ec703f27417..3c750ccbee25 100644
@@ -23,14 +23,17 @@
 
 /* PLL Configuration Register (xPLLCFG) */
 #define PLL_CFG_OFFSET		0x08
+#define IMX8ULP_PLL_CFG_OFFSET	0x10
 #define BP_PLL_MULT		16
 #define BM_PLL_MULT		(0x7f << 16)
 
 /* PLL Numerator Register (xPLLNUM) */
 #define PLL_NUM_OFFSET		0x10
+#define IMX8ULP_PLL_NUM_OFFSET	0x1c
 
 /* PLL Denominator Register (xPLLDENOM) */
 #define PLL_DENOM_OFFSET	0x14
+#define IMX8ULP_PLL_DENOM_OFFSET	0x18
 
 #define MAX_MFD			0x3fffffff
 #define DEFAULT_MFD		1000000
@@ -38,6 +41,9 @@
 struct clk_pllv4 {
 	struct clk_hw	hw;
 	void __iomem	*base;
+	u32		cfg_offset;
+	u32		num_offset;
+	u32		denom_offset;
 };
 
 /* Valid PLL MULT Table */
@@ -72,12 +78,12 @@ static unsigned long clk_pllv4_recalc_rate(struct clk_hw *hw,
 	u32 mult, mfn, mfd;
 	u64 temp64;
 
-	mult = readl_relaxed(pll->base + PLL_CFG_OFFSET);
+	mult = readl_relaxed(pll->base + pll->cfg_offset);
 	mult &= BM_PLL_MULT;
 	mult >>= BP_PLL_MULT;
 
-	mfn = readl_relaxed(pll->base + PLL_NUM_OFFSET);
-	mfd = readl_relaxed(pll->base + PLL_DENOM_OFFSET);
+	mfn = readl_relaxed(pll->base + pll->num_offset);
+	mfd = readl_relaxed(pll->base + pll->denom_offset);
 	temp64 = parent_rate;
 	temp64 *= mfn;
 	do_div(temp64, mfd);
@@ -165,13 +171,13 @@ static int clk_pllv4_set_rate(struct clk_hw *hw, unsigned long rate,
 	do_div(temp64, parent_rate);
 	mfn = temp64;
 
-	val = readl_relaxed(pll->base + PLL_CFG_OFFSET);
+	val = readl_relaxed(pll->base + pll->cfg_offset);
 	val &= ~BM_PLL_MULT;
 	val |= mult << BP_PLL_MULT;
-	writel_relaxed(val, pll->base + PLL_CFG_OFFSET);
+	writel_relaxed(val, pll->base + pll->cfg_offset);
 
-	writel_relaxed(mfn, pll->base + PLL_NUM_OFFSET);
-	writel_relaxed(mfd, pll->base + PLL_DENOM_OFFSET);
+	writel_relaxed(mfn, pll->base + pll->num_offset);
+	writel_relaxed(mfd, pll->base + pll->denom_offset);
 
 	return 0;
 }
@@ -207,8 +213,8 @@ static const struct clk_ops clk_pllv4_ops = {
 	.is_prepared	= clk_pllv4_is_prepared,
 };
 
-struct clk_hw *imx_clk_hw_pllv4(const char *name, const char *parent_name,
-			  void __iomem *base)
+struct clk_hw *imx_clk_hw_pllv4(enum imx_pllv4_type type, const char *name,
+		 const char *parent_name, void __iomem *base)
 {
 	struct clk_pllv4 *pll;
 	struct clk_hw *hw;
@@ -221,6 +227,16 @@ struct clk_hw *imx_clk_hw_pllv4(const char *name, const char *parent_name,
 
 	pll->base = base;
 
+	if (type == IMX_PLLV4_IMX8ULP) {
+		pll->cfg_offset = IMX8ULP_PLL_CFG_OFFSET;
+		pll->num_offset = IMX8ULP_PLL_NUM_OFFSET;
+		pll->denom_offset = IMX8ULP_PLL_DENOM_OFFSET;
+	} else {
+		pll->cfg_offset = PLL_CFG_OFFSET;
+		pll->num_offset = PLL_NUM_OFFSET;
+		pll->denom_offset = PLL_DENOM_OFFSET;
+	}
+
 	init.name = name;
 	init.ops = &clk_pllv4_ops;
 	init.parent_names = &parent_name;
drivers/clk/imx/clk.h +7 -2
index e144f983fd8c..3f518559b8f9 100644
@@ -42,6 +42,11 @@ enum imx_pll14xx_type {
 	PLL_1443X,
 };
 
+enum imx_pllv4_type {
+	IMX_PLLV4_IMX7ULP,
+	IMX_PLLV4_IMX8ULP,
+};
+
 /* NOTE: Rate table should be kept sorted in descending order. */
 struct imx_pll14xx_rate_table {
 	unsigned int rate;
@@ -191,8 +196,8 @@ struct clk_hw *imx_clk_hw_pllv3(enum imx_pllv3_type type, const char *name,
 		.kdiv	=	(_k),			\
 	}
 
-struct clk_hw *imx_clk_hw_pllv4(const char *name, const char *parent_name,
-			     void __iomem *base);
+struct clk_hw *imx_clk_hw_pllv4(enum imx_pllv4_type type, const char *name,
+		const char *parent_name, void __iomem *base);
 
 struct clk_hw *clk_hw_register_gate2(struct device *dev, const char *name,
 		const char *parent_name, unsigned long flags,
Signature · 1 line
2.26.2
Reviewed-by on v3 2/9
#7 lore raw

Re: [PATCH v3 2/9] clk: imx: Update the pllv4 to support imx8ulp

Quoted 5 lines · Jacky Bai

The PLLs used on i.MX8ULP is mostly the same as on i.MX7ULP, except the PLL register offset is changed. Change the PLLv4 driver for code reuse on i.MX7ULP and i.MX8ULP.

I'm OK with this one. But maybe later on we will have two separate wrappers in clk.h called imx_clk_hw_pllv4_7ulp and imx_clk_hw_pllv4_8ulp. We'll see.

Quoted 147 lines

---
v3 changes: no

---
 drivers/clk/imx/clk-imx7ulp.c |  4 ++--
 drivers/clk/imx/clk-pllv4.c   | 34 +++++++++++++++++++++++++---------
 drivers/clk/imx/clk.h         |  9 +++++++--
 3 files changed, 34 insertions(+), 13 deletions(-)
drivers/clk/imx/clk-imx7ulp.c +2 -2
index 779e09105da7..ba50d6db8097 100644
@@ -78,8 +78,8 @@ static void __init imx7ulp_clk_scg1_init(struct device_node *np)
 	hws[IMX7ULP_CLK_SPLL_PRE_DIV]	= imx_clk_hw_divider_flags("spll_pre_div", "spll_pre_sel", base + 0x608,	8,	3,	CLK_SET_RATE_GATE);
 
 	/*						name	 parent_name	 base */
-	hws[IMX7ULP_CLK_APLL]		= imx_clk_hw_pllv4("apll",  "apll_pre_div", base + 0x500);
-	hws[IMX7ULP_CLK_SPLL]		= imx_clk_hw_pllv4("spll",  "spll_pre_div", base + 0x600);
+	hws[IMX7ULP_CLK_APLL]		= imx_clk_hw_pllv4(IMX_PLLV4_IMX7ULP, "apll",  "apll_pre_div", base + 0x500);
+	hws[IMX7ULP_CLK_SPLL]		= imx_clk_hw_pllv4(IMX_PLLV4_IMX7ULP, "spll",  "spll_pre_div", base + 0x600);
 
 	/* APLL PFDs */
 	hws[IMX7ULP_CLK_APLL_PFD0]	= imx_clk_hw_pfdv2("apll_pfd0", "apll", base + 0x50c, 0);
drivers/clk/imx/clk-pllv4.c +25 -9
index 8ec703f27417..3c750ccbee25 100644
@@ -23,14 +23,17 @@
 
 /* PLL Configuration Register (xPLLCFG) */
 #define PLL_CFG_OFFSET		0x08
+#define IMX8ULP_PLL_CFG_OFFSET	0x10
 #define BP_PLL_MULT		16
 #define BM_PLL_MULT		(0x7f << 16)
 
 /* PLL Numerator Register (xPLLNUM) */
 #define PLL_NUM_OFFSET		0x10
+#define IMX8ULP_PLL_NUM_OFFSET	0x1c
 
 /* PLL Denominator Register (xPLLDENOM) */
 #define PLL_DENOM_OFFSET	0x14
+#define IMX8ULP_PLL_DENOM_OFFSET	0x18
 
 #define MAX_MFD			0x3fffffff
 #define DEFAULT_MFD		1000000
@@ -38,6 +41,9 @@
 struct clk_pllv4 {
 	struct clk_hw	hw;
 	void __iomem	*base;
+	u32		cfg_offset;
+	u32		num_offset;
+	u32		denom_offset;
 };
 
 /* Valid PLL MULT Table */
@@ -72,12 +78,12 @@ static unsigned long clk_pllv4_recalc_rate(struct clk_hw *hw,
 	u32 mult, mfn, mfd;
 	u64 temp64;
 
-	mult = readl_relaxed(pll->base + PLL_CFG_OFFSET);
+	mult = readl_relaxed(pll->base + pll->cfg_offset);
 	mult &= BM_PLL_MULT;
 	mult >>= BP_PLL_MULT;
 
-	mfn = readl_relaxed(pll->base + PLL_NUM_OFFSET);
-	mfd = readl_relaxed(pll->base + PLL_DENOM_OFFSET);
+	mfn = readl_relaxed(pll->base + pll->num_offset);
+	mfd = readl_relaxed(pll->base + pll->denom_offset);
 	temp64 = parent_rate;
 	temp64 *= mfn;
 	do_div(temp64, mfd);
@@ -165,13 +171,13 @@ static int clk_pllv4_set_rate(struct clk_hw *hw, unsigned long rate,
 	do_div(temp64, parent_rate);
 	mfn = temp64;
 
-	val = readl_relaxed(pll->base + PLL_CFG_OFFSET);
+	val = readl_relaxed(pll->base + pll->cfg_offset);
 	val &= ~BM_PLL_MULT;
 	val |= mult << BP_PLL_MULT;
-	writel_relaxed(val, pll->base + PLL_CFG_OFFSET);
+	writel_relaxed(val, pll->base + pll->cfg_offset);
 
-	writel_relaxed(mfn, pll->base + PLL_NUM_OFFSET);
-	writel_relaxed(mfd, pll->base + PLL_DENOM_OFFSET);
+	writel_relaxed(mfn, pll->base + pll->num_offset);
+	writel_relaxed(mfd, pll->base + pll->denom_offset);
 
 	return 0;
 }
@@ -207,8 +213,8 @@ static const struct clk_ops clk_pllv4_ops = {
 	.is_prepared	= clk_pllv4_is_prepared,
 };
 
-struct clk_hw *imx_clk_hw_pllv4(const char *name, const char *parent_name,
-			  void __iomem *base)
+struct clk_hw *imx_clk_hw_pllv4(enum imx_pllv4_type type, const char *name,
+		 const char *parent_name, void __iomem *base)
 {
 	struct clk_pllv4 *pll;
 	struct clk_hw *hw;
@@ -221,6 +227,16 @@ struct clk_hw *imx_clk_hw_pllv4(const char *name, const char *parent_name,
 
 	pll->base = base;
 
+	if (type == IMX_PLLV4_IMX8ULP) {
+		pll->cfg_offset = IMX8ULP_PLL_CFG_OFFSET;
+		pll->num_offset = IMX8ULP_PLL_NUM_OFFSET;
+		pll->denom_offset = IMX8ULP_PLL_DENOM_OFFSET;
+	} else {
+		pll->cfg_offset = PLL_CFG_OFFSET;
+		pll->num_offset = PLL_NUM_OFFSET;
+		pll->denom_offset = PLL_DENOM_OFFSET;
+	}
+
 	init.name = name;
 	init.ops = &clk_pllv4_ops;
 	init.parent_names = &parent_name;
drivers/clk/imx/clk.h +7 -2
index e144f983fd8c..3f518559b8f9 100644
@@ -42,6 +42,11 @@ enum imx_pll14xx_type {
 	PLL_1443X,
 };
 
+enum imx_pllv4_type {
+	IMX_PLLV4_IMX7ULP,
+	IMX_PLLV4_IMX8ULP,
+};
+
 /* NOTE: Rate table should be kept sorted in descending order. */
 struct imx_pll14xx_rate_table {
 	unsigned int rate;
@@ -191,8 +196,8 @@ struct clk_hw *imx_clk_hw_pllv3(enum imx_pllv3_type type, const char *name,
 		.kdiv	=	(_k),			\
 	}
 
-struct clk_hw *imx_clk_hw_pllv4(const char *name, const char *parent_name,
-			     void __iomem *base);
+struct clk_hw *imx_clk_hw_pllv4(enum imx_pllv4_type type, const char *name,
+		const char *parent_name, void __iomem *base);
 
 struct clk_hw *clk_hw_register_gate2(struct device *dev, const char *name,
 		const char *parent_name, unsigned long flags,
Signature · 1 line
2.26.2
author
#8 lore raw

PATCH v3 3/9 clk: imx: Update the compsite driver to support imx8ulp

In reply to Jacky Bai

On i.MX8ULP, some peripherals have a sw_rst control resides in the per device PCC clock control register, all others are same as i.MX7ULP, so update the 7ulp clock composite driver to support i.MX8ULP to maxmimize the code reuse.

---
v3 changs: no

---
 drivers/clk/imx/clk-composite-7ulp.c | 61 ++++++++++++++++++++++++++--
 drivers/clk/imx/clk.h                |  6 +++
 2 files changed, 64 insertions(+), 3 deletions(-)
drivers/clk/imx/clk-composite-7ulp.c +58 -3
index d85ba78abbb1..50ed383320bf 100644
@@ -23,11 +23,50 @@
 #define PCG_PCD_WIDTH	3
 #define PCG_PCD_MASK	0x7
 
-struct clk_hw *imx7ulp_clk_hw_composite(const char *name,
+#define SW_RST		BIT(28)
+
+static int pcc_gate_enable(struct clk_hw *hw)
+{
+	struct clk_gate *gate = to_clk_gate(hw);
+	u32 val;
+	int ret;
+
+	ret = clk_gate_ops.enable(hw);
+	if (ret)
+		return ret;
+
+	/*
+	 * release the sw reset for peripherals associated with
+	 * with this pcc clock.
+	 */
+	val = readl(gate->reg);
+	val |= SW_RST;
+	writel(val, gate->reg);
+
+	return 0;
+}
+
+static void pcc_gate_disable(struct clk_hw *hw)
+{
+	clk_gate_ops.disable(hw);
+}
+
+static int pcc_gate_is_enabled(struct clk_hw *hw)
+{
+	return clk_gate_ops.is_enabled(hw);
+}
+
+static const struct clk_ops pcc_gate_ops = {
+	.enable = pcc_gate_enable,
+	.disable = pcc_gate_disable,
+	.is_enabled = pcc_gate_is_enabled,
+};
+
+static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 				     const char * const *parent_names,
 				     int num_parents, bool mux_present,
 				     bool rate_present, bool gate_present,
-				     void __iomem *reg)
+				     void __iomem *reg, bool has_swrst)
 {
 	struct clk_hw *mux_hw = NULL, *fd_hw = NULL, *gate_hw = NULL;
 	struct clk_fractional_divider *fd = NULL;
@@ -77,7 +116,7 @@ struct clk_hw *imx7ulp_clk_hw_composite(const char *name,
 	hw = clk_hw_register_composite(NULL, name, parent_names, num_parents,
 				       mux_hw, &clk_mux_ops, fd_hw,
 				       &clk_fractional_divider_ops, gate_hw,
-				       &clk_gate_ops, CLK_SET_RATE_GATE |
+				       has_swrst ? &pcc_gate_ops : &clk_gate_ops, CLK_SET_RATE_GATE |
 				       CLK_SET_PARENT_GATE);
 	if (IS_ERR(hw)) {
 		kfree(mux);
@@ -87,3 +126,19 @@ struct clk_hw *imx7ulp_clk_hw_composite(const char *name,
 
 	return hw;
 }
+
+struct clk_hw *imx7ulp_clk_hw_composite(const char *name, const char * const *parent_names,
+				int num_parents, bool mux_present, bool rate_present,
+				bool gate_present, void __iomem *reg)
+{
+	return imx_ulp_clk_hw_composite(name, parent_names, num_parents, mux_present, rate_present,
+					gate_present, reg, false);
+}
+
+struct clk_hw *imx8ulp_clk_hw_composite(const char *name, const char * const *parent_names,
+				int num_parents, bool mux_present, bool rate_present,
+				bool gate_present, void __iomem *reg, bool has_swrst)
+{
+	return imx_ulp_clk_hw_composite(name, parent_names, num_parents, mux_present, rate_present,
+					gate_present, reg, has_swrst);
+}
drivers/clk/imx/clk.h +6 -0
index 3f518559b8f9..a9bcfee7a75b 100644
@@ -237,6 +237,12 @@ struct clk_hw *imx7ulp_clk_hw_composite(const char *name,
 				     bool rate_present, bool gate_present,
 				     void __iomem *reg);
 
+struct clk_hw *imx8ulp_clk_hw_composite(const char *name,
+				     const char * const *parent_names,
+				     int num_parents, bool mux_present,
+				     bool rate_present, bool gate_present,
+				     void __iomem *reg, bool has_swrst);
+
 struct clk_hw *imx_clk_hw_fixup_divider(const char *name, const char *parent,
 				  void __iomem *reg, u8 shift, u8 width,
 				  void (*fixup)(u32 *val));
Signature · 1 line
2.26.2
Reviewed-by on v3 3/9
#9 lore raw

Re: [PATCH v3 3/9] clk: imx: Update the compsite driver to support imx8ulp

Quoted 7 lines · Jacky Bai

On i.MX8ULP, some peripherals have a sw_rst control resides in the per device PCC clock control register, all others are same as i.MX7ULP, so update the 7ulp clock composite driver to support i.MX8ULP to maxmimize the code reuse.

Quoted 113 lines

---
v3 changs: no

---
 drivers/clk/imx/clk-composite-7ulp.c | 61 ++++++++++++++++++++++++++--
 drivers/clk/imx/clk.h                |  6 +++
 2 files changed, 64 insertions(+), 3 deletions(-)
drivers/clk/imx/clk-composite-7ulp.c +58 -3
index d85ba78abbb1..50ed383320bf 100644
@@ -23,11 +23,50 @@
 #define PCG_PCD_WIDTH	3
 #define PCG_PCD_MASK	0x7
 
-struct clk_hw *imx7ulp_clk_hw_composite(const char *name,
+#define SW_RST		BIT(28)
+
+static int pcc_gate_enable(struct clk_hw *hw)
+{
+	struct clk_gate *gate = to_clk_gate(hw);
+	u32 val;
+	int ret;
+
+	ret = clk_gate_ops.enable(hw);
+	if (ret)
+		return ret;
+
+	/*
+	 * release the sw reset for peripherals associated with
+	 * with this pcc clock.
+	 */
+	val = readl(gate->reg);
+	val |= SW_RST;
+	writel(val, gate->reg);
+
+	return 0;
+}
+
+static void pcc_gate_disable(struct clk_hw *hw)
+{
+	clk_gate_ops.disable(hw);
+}
+
+static int pcc_gate_is_enabled(struct clk_hw *hw)
+{
+	return clk_gate_ops.is_enabled(hw);
+}
+
+static const struct clk_ops pcc_gate_ops = {
+	.enable = pcc_gate_enable,
+	.disable = pcc_gate_disable,
+	.is_enabled = pcc_gate_is_enabled,
+};
+
+static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 				     const char * const *parent_names,
 				     int num_parents, bool mux_present,
 				     bool rate_present, bool gate_present,
-				     void __iomem *reg)
+				     void __iomem *reg, bool has_swrst)
 {
 	struct clk_hw *mux_hw = NULL, *fd_hw = NULL, *gate_hw = NULL;
 	struct clk_fractional_divider *fd = NULL;
@@ -77,7 +116,7 @@ struct clk_hw *imx7ulp_clk_hw_composite(const char *name,
 	hw = clk_hw_register_composite(NULL, name, parent_names, num_parents,
 				       mux_hw, &clk_mux_ops, fd_hw,
 				       &clk_fractional_divider_ops, gate_hw,
-				       &clk_gate_ops, CLK_SET_RATE_GATE |
+				       has_swrst ? &pcc_gate_ops : &clk_gate_ops, CLK_SET_RATE_GATE |
 				       CLK_SET_PARENT_GATE);
 	if (IS_ERR(hw)) {
 		kfree(mux);
@@ -87,3 +126,19 @@ struct clk_hw *imx7ulp_clk_hw_composite(const char *name,
 
 	return hw;
 }
+
+struct clk_hw *imx7ulp_clk_hw_composite(const char *name, const char * const *parent_names,
+				int num_parents, bool mux_present, bool rate_present,
+				bool gate_present, void __iomem *reg)
+{
+	return imx_ulp_clk_hw_composite(name, parent_names, num_parents, mux_present, rate_present,
+					gate_present, reg, false);
+}
+
+struct clk_hw *imx8ulp_clk_hw_composite(const char *name, const char * const *parent_names,
+				int num_parents, bool mux_present, bool rate_present,
+				bool gate_present, void __iomem *reg, bool has_swrst)
+{
+	return imx_ulp_clk_hw_composite(name, parent_names, num_parents, mux_present, rate_present,
+					gate_present, reg, has_swrst);
+}
drivers/clk/imx/clk.h +6 -0
index 3f518559b8f9..a9bcfee7a75b 100644
@@ -237,6 +237,12 @@ struct clk_hw *imx7ulp_clk_hw_composite(const char *name,
 				     bool rate_present, bool gate_present,
 				     void __iomem *reg);
 
+struct clk_hw *imx8ulp_clk_hw_composite(const char *name,
+				     const char * const *parent_names,
+				     int num_parents, bool mux_present,
+				     bool rate_present, bool gate_present,
+				     void __iomem *reg, bool has_swrst);
+
 struct clk_hw *imx_clk_hw_fixup_divider(const char *name, const char *parent,
 				  void __iomem *reg, u8 shift, u8 width,
 				  void (*fixup)(u32 *val));
Signature · 1 line
2.26.2
author
#10 lore raw

PATCH v3 4/9 clk: imx: disable i.mx7ulp composite clock during initialization

In reply to Jacky Bai

From: Anson Huang <[email protected]>

i.MX7ULP peripheral clock ONLY allow parent/rate to be changed with clock gated, however, during clock tree initialization, the peripheral clock could be enabled by bootloader, but the prepare count in clock tree is still zero, so clock core driver will allow parent/rate changed even with CLK_SET_RATE_GATE/CLK_SET_PARENT_GATE set, but the change will fail due to HW NOT allow parent/rate change with clock enabled. It will cause clock HW status mismatch with clock tree info and lead to function issue. Below is an example:

usdhc0's pcc clock value is 0xC5000000 during kernel boot up, it means usdhc0 clock is enabled, its parent is APLL_PFD1. In DT file, the usdhc0 clock settings are as below:

assigned-clocks = <&pcc2 IMX7ULP_CLK_USDHC0>; assigned-clock-parents = <&scg1 IMX7ULP_CLK_NIC1_DIV>;

when kernel boot up, the clock tree info is as below, but the usdhc0 PCC register is still 0xC5000000, which means its parent is still from APLL_PFD1, which is incorrect and cause usdhc0 NOT work.

nic1_clk 2 2 0 176000000 0 0 50000

    usdhc0       0        0        0   176000000          0     0  50000

After making sure the peripheral clock is disabled during clock tree initialization, the usdhc0 is working, and this change is necessary for all i.MX7ULP peripheral clocks.

---
v3 changes: no

---
 drivers/clk/imx/clk-composite-7ulp.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
drivers/clk/imx/clk-composite-7ulp.c +14 -0
index 50ed383320bf..92908ee4509d 100644
@@ -8,6 +8,7 @@
 #include <linux/bits.h>
 #include <linux/clk-provider.h>
 #include <linux/err.h>
+#include <linux/io.h>
 #include <linux/slab.h>
 
 #include "../clk-fractional-divider.h"
@@ -73,6 +74,7 @@ static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 	struct clk_gate *gate = NULL;
 	struct clk_mux *mux = NULL;
 	struct clk_hw *hw;
+	u32 val;
 
 	if (mux_present) {
 		mux = kzalloc(sizeof(*mux), GFP_KERNEL);
@@ -111,6 +113,18 @@ static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 		gate_hw = &gate->hw;
 		gate->reg = reg;
 		gate->bit_idx = PCG_CGC_SHIFT;
+		/*
+		 * make sure clock is gated during clock tree initialization,
+		 * the HW ONLY allow clock parent/rate changed with clock gated,
+		 * during clock tree initialization, clocks could be enabled
+		 * by bootloader, so the HW status will mismatch with clock tree
+		 * prepare count, then clock core driver will allow parent/rate
+		 * change since the prepare count is zero, but HW actually
+		 * prevent the parent/rate change due to the clock is enabled.
+		 */
+		val = readl_relaxed(reg);
+		val &= ~(1 << PCG_CGC_SHIFT);
+		writel_relaxed(val, reg);
 	}
 
 	hw = clk_hw_register_composite(NULL, name, parent_names, num_parents,
Signature · 1 line
2.26.2
Reviewed-by on v3 4/9
#11 lore raw

Re: [PATCH v3 4/9] clk: imx: disable i.mx7ulp composite clock during initialization

Quoted 22 lines · Jacky Bai

From: Anson Huang <[email protected]>

i.MX7ULP peripheral clock ONLY allow parent/rate to be changed with clock gated, however, during clock tree initialization, the peripheral clock could be enabled by bootloader, but the prepare count in clock tree is still zero, so clock core driver will allow parent/rate changed even with CLK_SET_RATE_GATE/CLK_SET_PARENT_GATE set, but the change will fail due to HW NOT allow parent/rate change with clock enabled. It will cause clock HW status mismatch with clock tree info and lead to function issue. Below is an example:

usdhc0's pcc clock value is 0xC5000000 during kernel boot up, it means usdhc0 clock is enabled, its parent is APLL_PFD1. In DT file, the usdhc0 clock settings are as below:

assigned-clocks = <&pcc2 IMX7ULP_CLK_USDHC0>; assigned-clock-parents = <&scg1 IMX7ULP_CLK_NIC1_DIV>;

when kernel boot up, the clock tree info is as below, but the usdhc0 PCC register is still 0xC5000000, which means its parent is still from APLL_PFD1, which is incorrect and cause usdhc0 NOT work.

Quoted 8 lines

nic1_clk 2 2 0 176000000 0 0 50000

    usdhc0       0        0        0   176000000          0     0  50000

After making sure the peripheral clock is disabled during clock tree initialization, the usdhc0 is working, and this change is necessary for all i.MX7ULP peripheral clocks.

Quoted 48 lines

---
v3 changes: no

---
 drivers/clk/imx/clk-composite-7ulp.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
drivers/clk/imx/clk-composite-7ulp.c +14 -0
index 50ed383320bf..92908ee4509d 100644
@@ -8,6 +8,7 @@
 #include <linux/bits.h>
 #include <linux/clk-provider.h>
 #include <linux/err.h>
+#include <linux/io.h>
 #include <linux/slab.h>
 
 #include "../clk-fractional-divider.h"
@@ -73,6 +74,7 @@ static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 	struct clk_gate *gate = NULL;
 	struct clk_mux *mux = NULL;
 	struct clk_hw *hw;
+	u32 val;
 
 	if (mux_present) {
 		mux = kzalloc(sizeof(*mux), GFP_KERNEL);
@@ -111,6 +113,18 @@ static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 		gate_hw = &gate->hw;
 		gate->reg = reg;
 		gate->bit_idx = PCG_CGC_SHIFT;
+		/*
+		 * make sure clock is gated during clock tree initialization,
+		 * the HW ONLY allow clock parent/rate changed with clock gated,
+		 * during clock tree initialization, clocks could be enabled
+		 * by bootloader, so the HW status will mismatch with clock tree
+		 * prepare count, then clock core driver will allow parent/rate
+		 * change since the prepare count is zero, but HW actually
+		 * prevent the parent/rate change due to the clock is enabled.
+		 */
+		val = readl_relaxed(reg);
+		val &= ~(1 << PCG_CGC_SHIFT);
+		writel_relaxed(val, reg);
 	}
 
 	hw = clk_hw_register_composite(NULL, name, parent_names, num_parents,
Signature · 1 line
2.26.2
author
#12 lore raw

PATCH v3 5/9 clk: imx: Add 'CLK_SET_RATE_NO_REPARENT' for composite-7ulp

In reply to Jacky Bai

For the imx_composite-7ulp clock type, The clock parent should be changed explicitly by end user of this clock, if the the 'CLK_SET_RATE_NO_REPARENT' flag is not set, when user want to set a clock frequency that can NOT get from HW accurately, then the clock's parent will be switch to another clock parent sometimes. This is NOT what we expected and introduced some additional debug effort, so add the 'CLK_SET_RATE_NO_REPARENT' to avoid such unexpected result.

---
v3 changs: no

---
 drivers/clk/imx/clk-composite-7ulp.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/clk/imx/clk-composite-7ulp.c +1 -1
index 92908ee4509d..9ce8c630ee32 100644
@@ -131,7 +131,7 @@ static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 				       mux_hw, &clk_mux_ops, fd_hw,
 				       &clk_fractional_divider_ops, gate_hw,
 				       has_swrst ? &pcc_gate_ops : &clk_gate_ops, CLK_SET_RATE_GATE |
-				       CLK_SET_PARENT_GATE);
+				       CLK_SET_PARENT_GATE | CLK_SET_RATE_NO_REPARENT);
 	if (IS_ERR(hw)) {
 		kfree(mux);
 		kfree(fd);
Signature · 1 line
2.26.2
Reviewed-by on v3 5/9
#13 lore raw

Re: [PATCH v3 5/9] clk: imx: Add 'CLK_SET_RATE_NO_REPARENT' for composite-7ulp

Quoted 10 lines · Jacky Bai

For the imx_composite-7ulp clock type, The clock parent should be changed explicitly by end user of this clock, if the the 'CLK_SET_RATE_NO_REPARENT' flag is not set, when user want to set a clock frequency that can NOT get from HW accurately, then the clock's parent will be switch to another clock parent sometimes. This is NOT what we expected and introduced some additional debug effort, so add the 'CLK_SET_RATE_NO_REPARENT' to avoid such unexpected result.

Quoted 22 lines

---
v3 changs: no

---
 drivers/clk/imx/clk-composite-7ulp.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/clk/imx/clk-composite-7ulp.c +1 -1
index 92908ee4509d..9ce8c630ee32 100644
@@ -131,7 +131,7 @@ static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 				       mux_hw, &clk_mux_ops, fd_hw,
 				       &clk_fractional_divider_ops, gate_hw,
 				       has_swrst ? &pcc_gate_ops : &clk_gate_ops, CLK_SET_RATE_GATE |
-				       CLK_SET_PARENT_GATE);
+				       CLK_SET_PARENT_GATE | CLK_SET_RATE_NO_REPARENT);
 	if (IS_ERR(hw)) {
 		kfree(mux);
 		kfree(fd);
Signature · 1 line
2.26.2
author
#14 lore raw

PATCH v3 6/9 clk: imx: disable the pfd when set pfdv2 clock rate

In reply to Jacky Bai

It is possible that a PFD is enabled in HW but not in SW. That means the enable count & prepare count of the PFD clock is '0', so the 'CLK_SET_RATE' flag can do nothing when the rate is changed while the PFD is hw enabled. In order to safely change the pfd rate, we can disable the PFD directly if it is hw enabled but not used by SW end user.

---
v3 changs: no

---
 drivers/clk/imx/clk-pfdv2.c | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)
drivers/clk/imx/clk-pfdv2.c +11 -2
index 6b744c84278e..9cba83521988 100644
@@ -161,8 +161,17 @@ static int clk_pfdv2_set_rate(struct clk_hw *hw, unsigned long rate,
 	if (!rate)
 		return -EINVAL;
 
-	/* PFD can NOT change rate without gating */
-	WARN_ON(clk_pfdv2_is_enabled(hw));
+	/*
+	 * PFD can NOT change rate without gating.
+	 * as the PFDs may enabled in HW by default but no
+	 * consumer used it, the enable count is '0', so the
+	 * 'SET_RATE_GATE' can NOT help on blocking the set_rate
+	 * ops especially for 'assigned-clock-xxx'. In order
+	 * to simplify the case, just disable the PFD if it is
+	 * enabled in HW but not in SW.
+	 */
+	if (clk_pfdv2_is_enabled(hw))
+		clk_pfdv2_disable(hw);
 
 	tmp = tmp * 18 + rate / 2;
 	do_div(tmp, rate);
Signature · 1 line
2.26.2
Reviewed-by on v3 6/9
#15 lore raw

Re: [PATCH v3 6/9] clk: imx: disable the pfd when set pfdv2 clock rate

Quoted 8 lines · Jacky Bai

It is possible that a PFD is enabled in HW but not in SW. That means the enable count & prepare count of the PFD clock is '0', so the 'CLK_SET_RATE' flag can do nothing when the rate is changed while the PFD is hw enabled. In order to safely change the pfd rate, we can disable the PFD directly if it is hw enabled but not used by SW end user.

Quoted 33 lines

---
v3 changs: no

---
 drivers/clk/imx/clk-pfdv2.c | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)
drivers/clk/imx/clk-pfdv2.c +11 -2
index 6b744c84278e..9cba83521988 100644
@@ -161,8 +161,17 @@ static int clk_pfdv2_set_rate(struct clk_hw *hw, unsigned long rate,
 	if (!rate)
 		return -EINVAL;
 
-	/* PFD can NOT change rate without gating */
-	WARN_ON(clk_pfdv2_is_enabled(hw));
+	/*
+	 * PFD can NOT change rate without gating.
+	 * as the PFDs may enabled in HW by default but no
+	 * consumer used it, the enable count is '0', so the
+	 * 'SET_RATE_GATE' can NOT help on blocking the set_rate
+	 * ops especially for 'assigned-clock-xxx'. In order
+	 * to simplify the case, just disable the PFD if it is
+	 * enabled in HW but not in SW.
+	 */
+	if (clk_pfdv2_is_enabled(hw))
+		clk_pfdv2_disable(hw);
 
 	tmp = tmp * 18 + rate / 2;
 	do_div(tmp, rate);
Signature · 1 line
2.26.2
author
#16 lore raw

PATCH v3 7/9 clk: imx: Update the pfdv2 for 8ulp specific support

In reply to Jacky Bai

On i.MX8ULP, the 'CLK_SET_RATE_PARENT' flag should NOT be set and according to the laest RM, the PFD divider value range seems will be changed in the future, so update the pfdv2 to include the specific support for i.MX8ULP.

---
v3 changs: no

---
 drivers/clk/imx/clk-imx7ulp.c | 16 ++++++++--------
 drivers/clk/imx/clk-pfdv2.c   |  9 ++++++---
 drivers/clk/imx/clk.h         |  9 +++++++--
 3 files changed, 21 insertions(+), 13 deletions(-)
drivers/clk/imx/clk-imx7ulp.c +8 -8
index ba50d6db8097..b6e45e77ee39 100644
@@ -82,16 +82,16 @@ static void __init imx7ulp_clk_scg1_init(struct device_node *np)
 	hws[IMX7ULP_CLK_SPLL]		= imx_clk_hw_pllv4(IMX_PLLV4_IMX7ULP, "spll",  "spll_pre_div", base + 0x600);
 
 	/* APLL PFDs */
-	hws[IMX7ULP_CLK_APLL_PFD0]	= imx_clk_hw_pfdv2("apll_pfd0", "apll", base + 0x50c, 0);
-	hws[IMX7ULP_CLK_APLL_PFD1]	= imx_clk_hw_pfdv2("apll_pfd1", "apll", base + 0x50c, 1);
-	hws[IMX7ULP_CLK_APLL_PFD2]	= imx_clk_hw_pfdv2("apll_pfd2", "apll", base + 0x50c, 2);
-	hws[IMX7ULP_CLK_APLL_PFD3]	= imx_clk_hw_pfdv2("apll_pfd3", "apll", base + 0x50c, 3);
+	hws[IMX7ULP_CLK_APLL_PFD0]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "apll_pfd0", "apll", base + 0x50c, 0);
+	hws[IMX7ULP_CLK_APLL_PFD1]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "apll_pfd1", "apll", base + 0x50c, 1);
+	hws[IMX7ULP_CLK_APLL_PFD2]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "apll_pfd2", "apll", base + 0x50c, 2);
+	hws[IMX7ULP_CLK_APLL_PFD3]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "apll_pfd3", "apll", base + 0x50c, 3);
 
 	/* SPLL PFDs */
-	hws[IMX7ULP_CLK_SPLL_PFD0]	= imx_clk_hw_pfdv2("spll_pfd0", "spll", base + 0x60C, 0);
-	hws[IMX7ULP_CLK_SPLL_PFD1]	= imx_clk_hw_pfdv2("spll_pfd1", "spll", base + 0x60C, 1);
-	hws[IMX7ULP_CLK_SPLL_PFD2]	= imx_clk_hw_pfdv2("spll_pfd2", "spll", base + 0x60C, 2);
-	hws[IMX7ULP_CLK_SPLL_PFD3]	= imx_clk_hw_pfdv2("spll_pfd3", "spll", base + 0x60C, 3);
+	hws[IMX7ULP_CLK_SPLL_PFD0]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "spll_pfd0", "spll", base + 0x60C, 0);
+	hws[IMX7ULP_CLK_SPLL_PFD1]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "spll_pfd1", "spll", base + 0x60C, 1);
+	hws[IMX7ULP_CLK_SPLL_PFD2]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "spll_pfd2", "spll", base + 0x60C, 2);
+	hws[IMX7ULP_CLK_SPLL_PFD3]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "spll_pfd3", "spll", base + 0x60C, 3);
 
 	/* PLL Mux */
 	hws[IMX7ULP_CLK_APLL_PFD_SEL]	= imx_clk_hw_mux_flags("apll_pfd_sel", base + 0x508, 14, 2, apll_pfd_sels, ARRAY_SIZE(apll_pfd_sels), CLK_SET_RATE_PARENT | CLK_SET_PARENT_GATE);
drivers/clk/imx/clk-pfdv2.c +6 -3
index 9cba83521988..42505669cdfb 100644
@@ -200,8 +200,8 @@ static const struct clk_ops clk_pfdv2_ops = {
 	.is_enabled     = clk_pfdv2_is_enabled,
 };
 
-struct clk_hw *imx_clk_hw_pfdv2(const char *name, const char *parent_name,
-			     void __iomem *reg, u8 idx)
+struct clk_hw *imx_clk_hw_pfdv2(enum imx_pfdv2_type type, const char *name,
+			     const char *parent_name, void __iomem *reg, u8 idx)
 {
 	struct clk_init_data init;
 	struct clk_pfdv2 *pfd;
@@ -223,7 +223,10 @@ struct clk_hw *imx_clk_hw_pfdv2(const char *name, const char *parent_name,
 	init.ops = &clk_pfdv2_ops;
 	init.parent_names = &parent_name;
 	init.num_parents = 1;
-	init.flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT;
+	if (type == IMX_PFDV2_IMX7ULP)
+		init.flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT;
+	else
+		init.flags = CLK_SET_RATE_GATE;
 
 	pfd->hw.init = &init;
 
drivers/clk/imx/clk.h +7 -2
index a9bcfee7a75b..45be7ba23fae 100644
@@ -47,6 +47,11 @@ enum imx_pllv4_type {
 	IMX_PLLV4_IMX8ULP,
 };
 
+enum imx_pfdv2_type {
+	IMX_PFDV2_IMX7ULP,
+	IMX_PFDV2_IMX8ULP,
+};
+
 /* NOTE: Rate table should be kept sorted in descending order. */
 struct imx_pll14xx_rate_table {
 	unsigned int rate;
@@ -220,8 +225,8 @@ struct clk_hw *imx_clk_hw_gate_exclusive(const char *name, const char *parent,
 struct clk_hw *imx_clk_hw_pfd(const char *name, const char *parent_name,
 		void __iomem *reg, u8 idx);
 
-struct clk_hw *imx_clk_hw_pfdv2(const char *name, const char *parent_name,
-			     void __iomem *reg, u8 idx);
+struct clk_hw *imx_clk_hw_pfdv2(enum imx_pfdv2_type type, const char *name,
+	 const char *parent_name, void __iomem *reg, u8 idx);
 
 struct clk_hw *imx_clk_hw_busy_divider(const char *name, const char *parent_name,
 				 void __iomem *reg, u8 shift, u8 width,
Signature · 1 line
2.26.2
Reviewed-by on v3 7/9
#17 lore raw

Re: [PATCH v3 7/9] clk: imx: Update the pfdv2 for 8ulp specific support

Quoted 6 lines · Jacky Bai

On i.MX8ULP, the 'CLK_SET_RATE_PARENT' flag should NOT be set and according to the laest RM, the PFD divider value range seems will be changed in the future, so update the pfdv2 to include the specific support for i.MX8ULP.

Quoted 94 lines

---
v3 changs: no

---
 drivers/clk/imx/clk-imx7ulp.c | 16 ++++++++--------
 drivers/clk/imx/clk-pfdv2.c   |  9 ++++++---
 drivers/clk/imx/clk.h         |  9 +++++++--
 3 files changed, 21 insertions(+), 13 deletions(-)
drivers/clk/imx/clk-imx7ulp.c +8 -8
index ba50d6db8097..b6e45e77ee39 100644
@@ -82,16 +82,16 @@ static void __init imx7ulp_clk_scg1_init(struct device_node *np)
 	hws[IMX7ULP_CLK_SPLL]		= imx_clk_hw_pllv4(IMX_PLLV4_IMX7ULP, "spll",  "spll_pre_div", base + 0x600);
 
 	/* APLL PFDs */
-	hws[IMX7ULP_CLK_APLL_PFD0]	= imx_clk_hw_pfdv2("apll_pfd0", "apll", base + 0x50c, 0);
-	hws[IMX7ULP_CLK_APLL_PFD1]	= imx_clk_hw_pfdv2("apll_pfd1", "apll", base + 0x50c, 1);
-	hws[IMX7ULP_CLK_APLL_PFD2]	= imx_clk_hw_pfdv2("apll_pfd2", "apll", base + 0x50c, 2);
-	hws[IMX7ULP_CLK_APLL_PFD3]	= imx_clk_hw_pfdv2("apll_pfd3", "apll", base + 0x50c, 3);
+	hws[IMX7ULP_CLK_APLL_PFD0]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "apll_pfd0", "apll", base + 0x50c, 0);
+	hws[IMX7ULP_CLK_APLL_PFD1]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "apll_pfd1", "apll", base + 0x50c, 1);
+	hws[IMX7ULP_CLK_APLL_PFD2]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "apll_pfd2", "apll", base + 0x50c, 2);
+	hws[IMX7ULP_CLK_APLL_PFD3]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "apll_pfd3", "apll", base + 0x50c, 3);
 
 	/* SPLL PFDs */
-	hws[IMX7ULP_CLK_SPLL_PFD0]	= imx_clk_hw_pfdv2("spll_pfd0", "spll", base + 0x60C, 0);
-	hws[IMX7ULP_CLK_SPLL_PFD1]	= imx_clk_hw_pfdv2("spll_pfd1", "spll", base + 0x60C, 1);
-	hws[IMX7ULP_CLK_SPLL_PFD2]	= imx_clk_hw_pfdv2("spll_pfd2", "spll", base + 0x60C, 2);
-	hws[IMX7ULP_CLK_SPLL_PFD3]	= imx_clk_hw_pfdv2("spll_pfd3", "spll", base + 0x60C, 3);
+	hws[IMX7ULP_CLK_SPLL_PFD0]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "spll_pfd0", "spll", base + 0x60C, 0);
+	hws[IMX7ULP_CLK_SPLL_PFD1]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "spll_pfd1", "spll", base + 0x60C, 1);
+	hws[IMX7ULP_CLK_SPLL_PFD2]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "spll_pfd2", "spll", base + 0x60C, 2);
+	hws[IMX7ULP_CLK_SPLL_PFD3]	= imx_clk_hw_pfdv2(IMX_PFDV2_IMX7ULP, "spll_pfd3", "spll", base + 0x60C, 3);
 
 	/* PLL Mux */
 	hws[IMX7ULP_CLK_APLL_PFD_SEL]	= imx_clk_hw_mux_flags("apll_pfd_sel", base + 0x508, 14, 2, apll_pfd_sels, ARRAY_SIZE(apll_pfd_sels), CLK_SET_RATE_PARENT | CLK_SET_PARENT_GATE);
drivers/clk/imx/clk-pfdv2.c +6 -3
index 9cba83521988..42505669cdfb 100644
@@ -200,8 +200,8 @@ static const struct clk_ops clk_pfdv2_ops = {
 	.is_enabled     = clk_pfdv2_is_enabled,
 };
 
-struct clk_hw *imx_clk_hw_pfdv2(const char *name, const char *parent_name,
-			     void __iomem *reg, u8 idx)
+struct clk_hw *imx_clk_hw_pfdv2(enum imx_pfdv2_type type, const char *name,
+			     const char *parent_name, void __iomem *reg, u8 idx)
 {
 	struct clk_init_data init;
 	struct clk_pfdv2 *pfd;
@@ -223,7 +223,10 @@ struct clk_hw *imx_clk_hw_pfdv2(const char *name, const char *parent_name,
 	init.ops = &clk_pfdv2_ops;
 	init.parent_names = &parent_name;
 	init.num_parents = 1;
-	init.flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT;
+	if (type == IMX_PFDV2_IMX7ULP)
+		init.flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT;
+	else
+		init.flags = CLK_SET_RATE_GATE;
 
 	pfd->hw.init = &init;
 
drivers/clk/imx/clk.h +7 -2
index a9bcfee7a75b..45be7ba23fae 100644
@@ -47,6 +47,11 @@ enum imx_pllv4_type {
 	IMX_PLLV4_IMX8ULP,
 };
 
+enum imx_pfdv2_type {
+	IMX_PFDV2_IMX7ULP,
+	IMX_PFDV2_IMX8ULP,
+};
+
 /* NOTE: Rate table should be kept sorted in descending order. */
 struct imx_pll14xx_rate_table {
 	unsigned int rate;
@@ -220,8 +225,8 @@ struct clk_hw *imx_clk_hw_gate_exclusive(const char *name, const char *parent,
 struct clk_hw *imx_clk_hw_pfd(const char *name, const char *parent_name,
 		void __iomem *reg, u8 idx);
 
-struct clk_hw *imx_clk_hw_pfdv2(const char *name, const char *parent_name,
-			     void __iomem *reg, u8 idx);
+struct clk_hw *imx_clk_hw_pfdv2(enum imx_pfdv2_type type, const char *name,
+	 const char *parent_name, void __iomem *reg, u8 idx);
 
 struct clk_hw *imx_clk_hw_busy_divider(const char *name, const char *parent_name,
 				 void __iomem *reg, u8 shift, u8 width,
Signature · 1 line
2.26.2
author
#18 lore raw

PATCH v3 8/9 clk: imx: Add clock driver for imx8ulp

In reply to Jacky Bai

Add clock driver for i.MX8ULP.

---
v3 changes:
- no

v2 changes:
- remove the redundent fixed sosc, fosc etc clock register

---
 drivers/clk/imx/Kconfig       |   6 +
 drivers/clk/imx/Makefile      |   2 +
 drivers/clk/imx/clk-imx8ulp.c | 459 ++++++++++++++++++++++++++++++++++
 3 files changed, 467 insertions(+)
 create mode 100644 drivers/clk/imx/clk-imx8ulp.c
drivers/clk/imx/Kconfig +6 -0
index 47d9ec3abd2f..b81d6437ed95 100644
@@ -98,3 +98,9 @@ config CLK_IMX8QXP
 	select MXC_CLK_SCU
 	help
 	  Build the driver for IMX8QXP SCU based clocks.
+
+config CLK_IMX8ULP
+	tristate "IMX8ULP CCM Clock Driver"
+	depends on ARCH_MXC || COMPILE_TEST
+	help
+	    Build the driver for i.MX8ULP CCM Clock Driver
drivers/clk/imx/Makefile +2 -0
index c24a2acbfa56..b5e040026dfb 100644
@@ -31,6 +31,8 @@ clk-imx-scu-$(CONFIG_CLK_IMX8QXP) += clk-scu.o clk-imx8qxp.o \
 				     clk-imx8qxp-rsrc.o clk-imx8qm-rsrc.o
 clk-imx-lpcg-scu-$(CONFIG_CLK_IMX8QXP) += clk-lpcg-scu.o clk-imx8qxp-lpcg.o
 
+obj-$(CONFIG_CLK_IMX8ULP) += clk-imx8ulp.o
+
 obj-$(CONFIG_CLK_IMX1)   += clk-imx1.o
 obj-$(CONFIG_CLK_IMX25)  += clk-imx25.o
 obj-$(CONFIG_CLK_IMX27)  += clk-imx27.o
drivers/clk/imx/clk-imx8ulp.c new file +459 -0

459 lines not on this page · raw message

Signature · 1 line
2.26.2
Reviewed-by on v3 8/9
#19 lore raw

Re: [PATCH v3 8/9] clk: imx: Add clock driver for imx8ulp

Quoted 4 lines · Jacky Bai

Add clock driver for i.MX8ULP.

Looks good to me.

Quoted 508 lines

---
v3 changes:
- no

v2 changes:
- remove the redundent fixed sosc, fosc etc clock register

---
 drivers/clk/imx/Kconfig       |   6 +
 drivers/clk/imx/Makefile      |   2 +
 drivers/clk/imx/clk-imx8ulp.c | 459 ++++++++++++++++++++++++++++++++++
 3 files changed, 467 insertions(+)
 create mode 100644 drivers/clk/imx/clk-imx8ulp.c
drivers/clk/imx/Kconfig +6 -0
index 47d9ec3abd2f..b81d6437ed95 100644
@@ -98,3 +98,9 @@ config CLK_IMX8QXP
 	select MXC_CLK_SCU
 	help
 	  Build the driver for IMX8QXP SCU based clocks.
+
+config CLK_IMX8ULP
+	tristate "IMX8ULP CCM Clock Driver"
+	depends on ARCH_MXC || COMPILE_TEST
+	help
+	    Build the driver for i.MX8ULP CCM Clock Driver
drivers/clk/imx/Makefile +2 -0
index c24a2acbfa56..b5e040026dfb 100644
@@ -31,6 +31,8 @@ clk-imx-scu-$(CONFIG_CLK_IMX8QXP) += clk-scu.o clk-imx8qxp.o \
 				     clk-imx8qxp-rsrc.o clk-imx8qm-rsrc.o
 clk-imx-lpcg-scu-$(CONFIG_CLK_IMX8QXP) += clk-lpcg-scu.o clk-imx8qxp-lpcg.o
 
+obj-$(CONFIG_CLK_IMX8ULP) += clk-imx8ulp.o
+
 obj-$(CONFIG_CLK_IMX1)   += clk-imx1.o
 obj-$(CONFIG_CLK_IMX25)  += clk-imx25.o
 obj-$(CONFIG_CLK_IMX27)  += clk-imx27.o
drivers/clk/imx/clk-imx8ulp.c new file +459 -0
new file mode 100644
index 000000000000..6aad04114658
@@ -0,0 +1,459 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2021 NXP
+ */
+
+#include <dt-bindings/clock/imx8ulp-clock.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include "clk.h"
+
+static const char * const pll_pre_sels[] = { "sosc", "frosc", };
+static const char * const a35_sels[] = { "frosc", "spll2", "sosc", "lvds", };
+static const char * const nic_sels[] = { "frosc", "spll3_pfd0", "sosc", "lvds", };
+static const char * const pcc3_periph_bus_sels[] = { "dummy", "lposc", "sosc_div2",
+						     "frosc_div2", "xbar_divbus", "spll3_pfd1_div1",
+						     "spll3_pfd0_div2", "spll3_pfd0_div1", };
+static const char * const pcc4_periph_bus_sels[] = { "dummy", "dummy", "lposc",
+						     "sosc_div2", "frosc_div2", "xbar_divbus",
+						     "spll3_vcodiv", "spll3_pfd0_div1", };
+static const char * const pcc4_periph_plat_sels[] = { "dummy", "sosc_div1", "frosc_div1",
+						      "spll3_pfd3_div2", "spll3_pfd3_div1",
+						      "spll3_pfd2_div2", "spll3_pfd2_div1",
+						      "spll3_pfd1_div2", };
+static const char * const pcc5_periph_bus_sels[] = { "dummy", "dummy", "lposc",
+						     "sosc_div2", "frosc_div2", "lpav_bus_clk",
+						     "pll4_vcodiv", "pll4_pfd3_div1", };
+static const char * const pcc5_periph_plat_sels[] = { "dummy", "pll4_pfd3_div2", "pll4_pfd2_div2",
+						      "pll4_pfd2_div1", "pll4_pfd1_div2",
+						      "pll4_pfd1_div1", "pll4_pfd0_div2",
+						      "pll4_pfd0_div1", };
+static const char * const hifi_sels[] = { "frosc", "pll4", "pll4_pfd0", "sosc",
+					 "lvds", "dummy", "dummy", "dummy", };
+static const char * const ddr_sels[] = { "frosc", "pll4_pfd1", "sosc", "lvds",
+					 "pll4", "pll4", "pll4", "pll4", };
+static const char * const lpav_sels[] = { "frosc", "pll4_pfd1", "sosc", "lvds", };
+static const char * const sai45_sels[] = { "spll3_pfd1_div1", "aud_clk1", "aud_clk2", "sosc", };
+static const char * const sai67_sels[] = { "spll1_pfd2_div", "spll3_pfd1_div1", "aud_clk0", "aud_clk1", "aud_clk2", "sosc", "dummy", "dummy", };
+static const char * const aud_clk1_sels[] = { "ext_aud_mclk2", "sai4_rx_bclk", "sai4_tx_bclk", "sai5_rx_bclk", "sai5_tx_bclk", "dummy", "dummy", "dummy", };
+static const char * const aud_clk2_sels[] = { "ext_aud_mclk3", "sai6_rx_bclk", "sai6_tx_bclk", "sai7_rx_bclk", "sai7_tx_bclk", "spdif_rx", "dummy", "dummy", };
+static const char * const enet_ts_sels[] = { "ext_rmii_clk", "ext_ts_clk", "rosc", "ext_aud_mclk", "sosc", "dummy", "dummy", "dummy"};
+static const char * const xbar_divbus[] = { "xbar_divbus" };
+static const char * const nic_per_divplat[] = { "nic_per_divplat" };
+static const char * const lpav_axi_div[] = { "lpav_axi_div" };
+static const char * const lpav_bus_div[] = { "lpav_bus_div" };
+
+static int imx8ulp_clk_cgc1_init(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct clk_hw_onecell_data *clk_data;
+	struct clk_hw **clks;
+	void __iomem *base;
+
+	clk_data = devm_kzalloc(dev, struct_size(clk_data, hws, IMX8ULP_CLK_CGC1_END),
+			   GFP_KERNEL);
+	if (!clk_data)
+		return -ENOMEM;
+
+	clk_data->num = IMX8ULP_CLK_CGC1_END;
+	clks = clk_data->hws;
+
+	clks[IMX8ULP_CLK_DUMMY] = imx_clk_hw_fixed("dummy", 0);
+
+	/* CGC1 */
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (WARN_ON(IS_ERR(base)))
+		return PTR_ERR(base);
+
+	clks[IMX8ULP_CLK_SPLL2_PRE_SEL]	= imx_clk_hw_mux_flags("spll2_pre_sel", base + 0x510, 0, 1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
+	clks[IMX8ULP_CLK_SPLL3_PRE_SEL]	= imx_clk_hw_mux_flags("spll3_pre_sel", base + 0x610, 0, 1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
+
+	clks[IMX8ULP_CLK_SPLL2] = imx_clk_hw_pllv4(IMX_PLLV4_IMX8ULP, "spll2", "spll2_pre_sel", base + 0x500);
+	clks[IMX8ULP_CLK_SPLL3] = imx_clk_hw_pllv4(IMX_PLLV4_IMX8ULP, "spll3", "spll3_pre_sel", base + 0x600);
+	clks[IMX8ULP_CLK_SPLL3_VCODIV] = imx_clk_hw_divider("spll3_vcodiv", "spll3", base + 0x604, 0, 6);
+
+	clks[IMX8ULP_CLK_SPLL3_PFD0] = imx_clk_hw_pfdv2(IMX_PFDV2_IMX8ULP, "spll3_pfd0", "spll3_vcodiv", base + 0x614, 0);
+	clks[IMX8ULP_CLK_SPLL3_PFD1] = imx_clk_hw_pfdv2(IMX_PFDV2_IMX8ULP, "spll3_pfd1", "spll3_vcodiv", base + 0x614, 1);
+	clks[IMX8ULP_CLK_SPLL3_PFD2] = imx_clk_hw_pfdv2(IMX_PFDV2_IMX8ULP, "spll3_pfd2", "spll3_vcodiv", base + 0x614, 2);
+	clks[IMX8ULP_CLK_SPLL3_PFD3] = imx_clk_hw_pfdv2(IMX_PFDV2_IMX8ULP, "spll3_pfd3", "spll3_vcodiv", base + 0x614, 3);
+
+	clks[IMX8ULP_CLK_SPLL3_PFD0_DIV1_GATE] = imx_clk_hw_gate_dis("spll3_pfd0_div1_gate", "spll3_pfd0", base + 0x608, 7);
+	clks[IMX8ULP_CLK_SPLL3_PFD0_DIV2_GATE] = imx_clk_hw_gate_dis("spll3_pfd0_div2_gate", "spll3_pfd0", base + 0x608, 15);
+	clks[IMX8ULP_CLK_SPLL3_PFD1_DIV1_GATE] = imx_clk_hw_gate_dis("spll3_pfd1_div1_gate", "spll3_pfd1", base + 0x608, 23);
+	clks[IMX8ULP_CLK_SPLL3_PFD1_DIV2_GATE] = imx_clk_hw_gate_dis("spll3_pfd1_div2_gate", "spll3_pfd1", base + 0x608, 31);
+	clks[IMX8ULP_CLK_SPLL3_PFD2_DIV1_GATE] = imx_clk_hw_gate_dis("spll3_pfd2_div1_gate", "spll3_pfd2", base + 0x60c, 7);
+	clks[IMX8ULP_CLK_SPLL3_PFD2_DIV2_GATE] = imx_clk_hw_gate_dis("spll3_pfd2_div2_gate", "spll3_pfd2", base + 0x60c, 15);
+	clks[IMX8ULP_CLK_SPLL3_PFD3_DIV1_GATE] = imx_clk_hw_gate_dis("spll3_pfd3_div1_gate", "spll3_pfd3", base + 0x60c, 23);
+	clks[IMX8ULP_CLK_SPLL3_PFD3_DIV2_GATE] = imx_clk_hw_gate_dis("spll3_pfd3_div2_gate", "spll3_pfd3", base + 0x60c, 31);
+	clks[IMX8ULP_CLK_SPLL3_PFD0_DIV1] = imx_clk_hw_divider("spll3_pfd0_div1", "spll3_pfd0_div1_gate", base + 0x608, 0, 6);
+	clks[IMX8ULP_CLK_SPLL3_PFD0_DIV2] = imx_clk_hw_divider("spll3_pfd0_div2", "spll3_pfd0_div2_gate", base + 0x608, 8, 6);
+	clks[IMX8ULP_CLK_SPLL3_PFD1_DIV1] = imx_clk_hw_divider("spll3_pfd1_div1", "spll3_pfd1_div1_gate", base + 0x608, 16, 6);
+	clks[IMX8ULP_CLK_SPLL3_PFD1_DIV2] = imx_clk_hw_divider("spll3_pfd1_div2", "spll3_pfd1_div2_gate", base + 0x608, 24, 6);
+	clks[IMX8ULP_CLK_SPLL3_PFD2_DIV1] = imx_clk_hw_divider("spll3_pfd2_div1", "spll3_pfd2_div1_gate", base + 0x60c, 0, 6);
+	clks[IMX8ULP_CLK_SPLL3_PFD2_DIV2] = imx_clk_hw_divider("spll3_pfd2_div2", "spll3_pfd2_div2_gate", base + 0x60c, 8, 6);
+	clks[IMX8ULP_CLK_SPLL3_PFD3_DIV1] = imx_clk_hw_divider("spll3_pfd3_div1", "spll3_pfd3_div1_gate", base + 0x60c, 16, 6);
+	clks[IMX8ULP_CLK_SPLL3_PFD3_DIV2] = imx_clk_hw_divider("spll3_pfd3_div2", "spll3_pfd3_div2_gate", base + 0x60c, 24, 6);
+
+	clks[IMX8ULP_CLK_A35_SEL] = imx_clk_hw_mux2("a35_sel", base + 0x14, 28, 2, a35_sels, ARRAY_SIZE(a35_sels));
+	clks[IMX8ULP_CLK_A35_DIV] = imx_clk_hw_divider_flags("a35_div", "a35_sel", base + 0x14, 21, 6, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+
+	clks[IMX8ULP_CLK_NIC_SEL] = imx_clk_hw_mux2("nic_sel", base + 0x34, 28, 2, nic_sels, ARRAY_SIZE(nic_sels));
+	clks[IMX8ULP_CLK_NIC_AD_DIVPLAT] = imx_clk_hw_divider_flags("nic_ad_divplat", "nic_sel", base + 0x34, 21, 6, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+	clks[IMX8ULP_CLK_NIC_PER_DIVPLAT] = imx_clk_hw_divider_flags("nic_per_divplat", "nic_ad_divplat", base + 0x34, 14, 6, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+	clks[IMX8ULP_CLK_XBAR_AD_DIVPLAT] = imx_clk_hw_divider_flags("xbar_ad_divplat", "nic_ad_divplat", base + 0x38, 14, 6, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+	clks[IMX8ULP_CLK_XBAR_DIVBUS] = imx_clk_hw_divider_flags("xbar_divbus", "nic_ad_divplat", base + 0x38, 7, 6, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+	clks[IMX8ULP_CLK_XBAR_AD_SLOW] = imx_clk_hw_divider_flags("xbar_ad_slow", "nic_ad_divplat", base + 0x38, 0, 6, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+
+	clks[IMX8ULP_CLK_SOSC_DIV1_GATE] = imx_clk_hw_gate_dis("sosc_div1_gate", "sosc", base + 0x108, 7);
+	clks[IMX8ULP_CLK_SOSC_DIV2_GATE] = imx_clk_hw_gate_dis("sosc_div2_gate", "sosc", base + 0x108, 15);
+	clks[IMX8ULP_CLK_SOSC_DIV3_GATE] = imx_clk_hw_gate_dis("sosc_div3_gate", "sosc", base + 0x108, 23);
+	clks[IMX8ULP_CLK_SOSC_DIV1] = imx_clk_hw_divider("sosc_div1", "sosc_div1_gate", base + 0x108, 0, 6);
+	clks[IMX8ULP_CLK_SOSC_DIV2] = imx_clk_hw_divider("sosc_div2", "sosc_div2_gate", base + 0x108, 8, 6);
+	clks[IMX8ULP_CLK_SOSC_DIV3] = imx_clk_hw_divider("sosc_div3", "sosc_div3_gate", base + 0x108, 16, 6);
+
+	clks[IMX8ULP_CLK_FROSC_DIV1_GATE] = imx_clk_hw_gate_dis("frosc_div1_gate", "frosc", base + 0x208, 7);
+	clks[IMX8ULP_CLK_FROSC_DIV2_GATE] = imx_clk_hw_gate_dis("frosc_div2_gate", "frosc", base + 0x208, 15);
+	clks[IMX8ULP_CLK_FROSC_DIV3_GATE] = imx_clk_hw_gate_dis("frosc_div3_gate", "frosc", base + 0x208, 23);
+	clks[IMX8ULP_CLK_FROSC_DIV1] = imx_clk_hw_divider("frosc_div1", "frosc_div1_gate", base + 0x208, 0, 6);
+	clks[IMX8ULP_CLK_FROSC_DIV2] = imx_clk_hw_divider("frosc_div2", "frosc_div2_gate", base + 0x208, 8, 6);
+	clks[IMX8ULP_CLK_FROSC_DIV3] = imx_clk_hw_divider("frosc_div3", "frosc_div3_gate", base + 0x208, 16, 6);
+	clks[IMX8ULP_CLK_AUD_CLK1] = imx_clk_hw_mux2("aud_clk1", base + 0x900, 0, 3, aud_clk1_sels, ARRAY_SIZE(aud_clk1_sels));
+	clks[IMX8ULP_CLK_SAI4_SEL] = imx_clk_hw_mux2("sai4_sel", base + 0x904, 0, 2, sai45_sels, ARRAY_SIZE(sai45_sels));
+	clks[IMX8ULP_CLK_SAI5_SEL] = imx_clk_hw_mux2("sai5_sel", base + 0x904, 8, 2, sai45_sels, ARRAY_SIZE(sai45_sels));
+	clks[IMX8ULP_CLK_ENET_TS_SEL] = imx_clk_hw_mux2("enet_ts", base + 0x700, 24, 3, enet_ts_sels, ARRAY_SIZE(enet_ts_sels));
+
+	imx_check_clk_hws(clks, clk_data->num);
+
+	return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, clk_data);
+}
+
+static int imx8ulp_clk_cgc2_init(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct clk_hw_onecell_data *clk_data;
+	struct clk_hw **clks;
+	void __iomem *base;
+
+	clk_data = devm_kzalloc(dev, struct_size(clk_data, hws, IMX8ULP_CLK_CGC2_END),
+			   GFP_KERNEL);
+	if (!clk_data)
+		return -ENOMEM;
+
+	clk_data->num = IMX8ULP_CLK_CGC2_END;
+	clks = clk_data->hws;
+
+	/* CGC2 */
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (WARN_ON(IS_ERR(base)))
+		return PTR_ERR(base);
+
+	clks[IMX8ULP_CLK_PLL4_PRE_SEL] = imx_clk_hw_mux_flags("pll4_pre_sel", base + 0x610, 0, 1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
+
+	clks[IMX8ULP_CLK_PLL4]	= imx_clk_hw_pllv4(IMX_PLLV4_IMX8ULP, "pll4", "pll4_pre_sel", base + 0x600);
+	clks[IMX8ULP_CLK_PLL4_VCODIV] = imx_clk_hw_divider("pll4_vcodiv", "pll4", base + 0x604, 0, 6);
+
+	clks[IMX8ULP_CLK_HIFI_SEL] = imx_clk_hw_mux_flags("hifi_sel", base + 0x14, 28, 3, hifi_sels, ARRAY_SIZE(hifi_sels), CLK_SET_PARENT_GATE);
+	clks[IMX8ULP_CLK_HIFI_DIVCORE] = imx_clk_hw_divider("hifi_core_div", "hifi_sel", base + 0x14, 21, 6);
+	clks[IMX8ULP_CLK_HIFI_DIVPLAT] = imx_clk_hw_divider("hifi_plat_div", "hifi_core_div", base + 0x14, 14, 6);
+
+	clks[IMX8ULP_CLK_DDR_SEL] = imx_clk_hw_mux_flags("ddr_sel", base + 0x40, 28, 3, ddr_sels, ARRAY_SIZE(ddr_sels), CLK_SET_PARENT_GATE);
+	clks[IMX8ULP_CLK_DDR_DIV] = imx_clk_hw_divider_flags("ddr_div", "ddr_sel", base + 0x40, 21, 6, CLK_IS_CRITICAL);
+	clks[IMX8ULP_CLK_LPAV_AXI_SEL] = imx_clk_hw_mux("lpav_sel", base + 0x3c, 28, 2, lpav_sels, ARRAY_SIZE(lpav_sels));
+	clks[IMX8ULP_CLK_LPAV_AXI_DIV] = imx_clk_hw_divider_flags("lpav_axi_div", "lpav_sel", base + 0x3c, 21, 6, CLK_IS_CRITICAL);
+	clks[IMX8ULP_CLK_LPAV_AHB_DIV] = imx_clk_hw_divider_flags("lpav_ahb_div", "lpav_axi_div", base + 0x3c, 14, 6, CLK_IS_CRITICAL);
+	clks[IMX8ULP_CLK_LPAV_BUS_DIV] = imx_clk_hw_divider_flags("lpav_bus_div", "lpav_axi_div", base + 0x3c, 7, 6, CLK_IS_CRITICAL);
+
+	clks[IMX8ULP_CLK_PLL4_PFD0] = imx_clk_hw_pfdv2(IMX_PFDV2_IMX8ULP, "pll4_pfd0", "pll4_vcodiv", base + 0x614, 0);
+	clks[IMX8ULP_CLK_PLL4_PFD1] = imx_clk_hw_pfdv2(IMX_PFDV2_IMX8ULP, "pll4_pfd1", "pll4_vcodiv", base + 0x614, 1);
+	clks[IMX8ULP_CLK_PLL4_PFD2] = imx_clk_hw_pfdv2(IMX_PFDV2_IMX8ULP, "pll4_pfd2", "pll4_vcodiv", base + 0x614, 2);
+	clks[IMX8ULP_CLK_PLL4_PFD3] = imx_clk_hw_pfdv2(IMX_PFDV2_IMX8ULP, "pll4_pfd3", "pll4_vcodiv", base + 0x614, 3);
+
+	clks[IMX8ULP_CLK_PLL4_PFD0_DIV1_GATE] = imx_clk_hw_gate_dis("pll4_pfd0_div1_gate", "pll4_pfd0", base + 0x608, 7);
+	clks[IMX8ULP_CLK_PLL4_PFD0_DIV2_GATE] = imx_clk_hw_gate_dis("pll4_pfd0_div2_gate", "pll4_pfd0", base + 0x608, 15);
+	clks[IMX8ULP_CLK_PLL4_PFD1_DIV1_GATE] = imx_clk_hw_gate_dis("pll4_pfd1_div1_gate", "pll4_pfd1", base + 0x608, 23);
+	clks[IMX8ULP_CLK_PLL4_PFD1_DIV2_GATE] = imx_clk_hw_gate_dis("pll4_pfd1_div2_gate", "pll4_pfd1", base + 0x608, 31);
+	clks[IMX8ULP_CLK_PLL4_PFD2_DIV1_GATE] = imx_clk_hw_gate_dis("pll4_pfd2_div1_gate", "pll4_pfd2", base + 0x60c, 7);
+	clks[IMX8ULP_CLK_PLL4_PFD2_DIV2_GATE] = imx_clk_hw_gate_dis("pll4_pfd2_div2_gate", "pll4_pfd2", base + 0x60c, 15);
+	clks[IMX8ULP_CLK_PLL4_PFD3_DIV1_GATE] = imx_clk_hw_gate_dis("pll4_pfd3_div1_gate", "pll4_pfd3", base + 0x60c, 23);
+	clks[IMX8ULP_CLK_PLL4_PFD3_DIV2_GATE] = imx_clk_hw_gate_dis("pll4_pfd3_div2_gate", "pll4_pfd3", base + 0x60c, 31);
+	clks[IMX8ULP_CLK_PLL4_PFD0_DIV1] = imx_clk_hw_divider("pll4_pfd0_div1", "pll4_pfd0_div1_gate", base + 0x608, 0, 6);
+	clks[IMX8ULP_CLK_PLL4_PFD0_DIV2] = imx_clk_hw_divider("pll4_pfd0_div2", "pll4_pfd0_div2_gate", base + 0x608, 8, 6);
+	clks[IMX8ULP_CLK_PLL4_PFD1_DIV1] = imx_clk_hw_divider("pll4_pfd1_div1", "pll4_pfd1_div1_gate", base + 0x608, 16, 6);
+	clks[IMX8ULP_CLK_PLL4_PFD1_DIV2] = imx_clk_hw_divider("pll4_pfd1_div2", "pll4_pfd1_div2_gate", base + 0x608, 24, 6);
+	clks[IMX8ULP_CLK_PLL4_PFD2_DIV1] = imx_clk_hw_divider("pll4_pfd2_div1", "pll4_pfd2_div1_gate", base + 0x60c, 0, 6);
+	clks[IMX8ULP_CLK_PLL4_PFD2_DIV2] = imx_clk_hw_divider("pll4_pfd2_div2", "pll4_pfd2_div2_gate", base + 0x60c, 8, 6);
+	clks[IMX8ULP_CLK_PLL4_PFD3_DIV1] = imx_clk_hw_divider("pll4_pfd3_div1", "pll4_pfd3_div1_gate", base + 0x60c, 16, 6);
+	clks[IMX8ULP_CLK_PLL4_PFD3_DIV2] = imx_clk_hw_divider("pll4_pfd3_div2", "pll4_pfd3_div2_gate", base + 0x60c, 24, 6);
+
+	clks[IMX8ULP_CLK_CGC2_SOSC_DIV1_GATE] = imx_clk_hw_gate_dis("cgc2_sosc_div1_gate", "sosc", base + 0x108, 7);
+	clks[IMX8ULP_CLK_CGC2_SOSC_DIV2_GATE] = imx_clk_hw_gate_dis("cgc2_sosc_div2_gate", "sosc", base + 0x108, 15);
+	clks[IMX8ULP_CLK_CGC2_SOSC_DIV3_GATE] = imx_clk_hw_gate_dis("cgc2_sosc_div3_gate", "sosc", base + 0x108, 23);
+	clks[IMX8ULP_CLK_CGC2_SOSC_DIV1] = imx_clk_hw_divider("cgc2_sosc_div1", "cgc2_sosc_div1_gate", base + 0x108, 0, 6);
+	clks[IMX8ULP_CLK_CGC2_SOSC_DIV2] = imx_clk_hw_divider("cgc2_sosc_div2", "cgc2_sosc_div2_gate", base + 0x108, 8, 6);
+	clks[IMX8ULP_CLK_CGC2_SOSC_DIV3] = imx_clk_hw_divider("cgc2_sosc_div3", "cgc2_sosc_div3_gate", base + 0x108, 16, 6);
+
+	clks[IMX8ULP_CLK_CGC2_FROSC_DIV1_GATE] = imx_clk_hw_gate_dis("cgc2_frosc_div1_gate", "frosc", base + 0x208, 7);
+	clks[IMX8ULP_CLK_CGC2_FROSC_DIV2_GATE] = imx_clk_hw_gate_dis("cgc2_frosc_div2_gate", "frosc", base + 0x208, 15);
+	clks[IMX8ULP_CLK_CGC2_FROSC_DIV3_GATE] = imx_clk_hw_gate_dis("cgc2_frosc_div3_gate", "frosc", base + 0x208, 23);
+	clks[IMX8ULP_CLK_CGC2_FROSC_DIV1] = imx_clk_hw_divider("cgc2_frosc_div1", "cgc2_frosc_div1_gate", base + 0x208, 0, 6);
+	clks[IMX8ULP_CLK_CGC2_FROSC_DIV2] = imx_clk_hw_divider("cgc2_frosc_div2", "cgc2_frosc_div2_gate", base + 0x208, 8, 6);
+	clks[IMX8ULP_CLK_CGC2_FROSC_DIV3] = imx_clk_hw_divider("cgc2_frosc_div3", "cgc2_frosc_div3_gate", base + 0x208, 16, 6);
+	clks[IMX8ULP_CLK_AUD_CLK2]  = imx_clk_hw_mux2("aud_clk2", base + 0x900, 0, 3, aud_clk2_sels, ARRAY_SIZE(aud_clk2_sels));
+	clks[IMX8ULP_CLK_SAI6_SEL]  = imx_clk_hw_mux2("sai6_sel", base + 0x904, 0, 3, sai67_sels, ARRAY_SIZE(sai67_sels));
+	clks[IMX8ULP_CLK_SAI7_SEL]  = imx_clk_hw_mux2("sai7_sel", base + 0x904, 8, 3, sai67_sels, ARRAY_SIZE(sai67_sels));
+	clks[IMX8ULP_CLK_SPDIF_SEL] = imx_clk_hw_mux2("spdif_sel", base + 0x910, 0, 3, sai67_sels, ARRAY_SIZE(sai67_sels));
+	clks[IMX8ULP_CLK_DSI_PHY_REF] = imx_clk_hw_fixed("dsi_phy_ref", 24000000);
+
+	imx_check_clk_hws(clks, clk_data->num);
+
+	return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, clk_data);
+}
+
+static int imx8ulp_clk_pcc3_init(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct clk_hw_onecell_data *clk_data;
+	struct clk_hw **clks;
+	void __iomem *base;
+	int ret;
+
+	clk_data = devm_kzalloc(dev, struct_size(clk_data, hws, IMX8ULP_CLK_PCC3_END),
+			   GFP_KERNEL);
+	if (!clk_data)
+		return -ENOMEM;
+
+	clk_data->num = IMX8ULP_CLK_PCC3_END;
+	clks = clk_data->hws;
+
+	/* PCC3 */
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (WARN_ON(IS_ERR(base)))
+		return PTR_ERR(base);
+
+	clks[IMX8ULP_CLK_WDOG3] = imx8ulp_clk_hw_composite("wdog3", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xa8, 1);
+	clks[IMX8ULP_CLK_WDOG4] = imx8ulp_clk_hw_composite("wdog4", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xac, 1);
+	clks[IMX8ULP_CLK_LPIT1] = imx8ulp_clk_hw_composite("lpit1", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xc8, 1);
+	clks[IMX8ULP_CLK_TPM4] = imx8ulp_clk_hw_composite("tpm4", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xcc, 1);
+	clks[IMX8ULP_CLK_TPM5] = imx8ulp_clk_hw_composite("tpm5", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xd0, 1);
+	clks[IMX8ULP_CLK_FLEXIO1] = imx8ulp_clk_hw_composite("flexio1", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xd4, 1);
+	clks[IMX8ULP_CLK_I3C2] = imx8ulp_clk_hw_composite("i3c2", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xd8, 1);
+	clks[IMX8ULP_CLK_LPI2C4] = imx8ulp_clk_hw_composite("lpi2c4", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xdc, 1);
+	clks[IMX8ULP_CLK_LPI2C5] = imx8ulp_clk_hw_composite("lpi2c5", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xe0, 1);
+	clks[IMX8ULP_CLK_LPUART4] = imx8ulp_clk_hw_composite("lpuart4", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xe4, 1);
+	clks[IMX8ULP_CLK_LPUART5] = imx8ulp_clk_hw_composite("lpuart5", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xe8, 1);
+	clks[IMX8ULP_CLK_LPSPI4] = imx8ulp_clk_hw_composite("lpspi4", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xec, 1);
+	clks[IMX8ULP_CLK_LPSPI5] = imx8ulp_clk_hw_composite("lpspi5", pcc3_periph_bus_sels, ARRAY_SIZE(pcc3_periph_bus_sels), true, true, true, base + 0xf0, 1);
+
+	clks[IMX8ULP_CLK_DMA1_MP] = imx_clk_hw_gate("pcc_dma1_mp", "xbar_ad_divplat", base + 0x4, 30);
+	clks[IMX8ULP_CLK_DMA1_CH0] = imx_clk_hw_gate("pcc_dma1_ch0", "xbar_ad_divplat", base + 0x8, 30);
+	clks[IMX8ULP_CLK_DMA1_CH1] = imx_clk_hw_gate("pcc_dma1_ch1", "xbar_ad_divplat", base + 0xc, 30);
+	clks[IMX8ULP_CLK_DMA1_CH2] = imx_clk_hw_gate("pcc_dma1_ch2", "xbar_ad_divplat", base + 0x10, 30);
+	clks[IMX8ULP_CLK_DMA1_CH3] = imx_clk_hw_gate("pcc_dma1_ch3", "xbar_ad_divplat", base + 0x14, 30);
+	clks[IMX8ULP_CLK_DMA1_CH4] = imx_clk_hw_gate("pcc_dma1_ch4", "xbar_ad_divplat", base + 0x18, 30);
+	clks[IMX8ULP_CLK_DMA1_CH5] = imx_clk_hw_gate("pcc_dma1_ch5", "xbar_ad_divplat", base + 0x1c, 30);
+	clks[IMX8ULP_CLK_DMA1_CH6] = imx_clk_hw_gate("pcc_dma1_ch6", "xbar_ad_divplat", base + 0x20, 30);
+	clks[IMX8ULP_CLK_DMA1_CH7] = imx_clk_hw_gate("pcc_dma1_ch7", "xbar_ad_divplat", base + 0x24, 30);
+	clks[IMX8ULP_CLK_DMA1_CH8] = imx_clk_hw_gate("pcc_dma1_ch8", "xbar_ad_divplat", base + 0x28, 30);
+	clks[IMX8ULP_CLK_DMA1_CH9] = imx_clk_hw_gate("pcc_dma1_ch9", "xbar_ad_divplat", base + 0x2c, 30);
+	clks[IMX8ULP_CLK_DMA1_CH10] = imx_clk_hw_gate("pcc_dma1_ch10", "xbar_ad_divplat", base + 0x30, 30);
+	clks[IMX8ULP_CLK_DMA1_CH11] = imx_clk_hw_gate("pcc_dma1_ch11", "xbar_ad_divplat", base + 0x34, 30);
+	clks[IMX8ULP_CLK_DMA1_CH12] = imx_clk_hw_gate("pcc_dma1_ch12", "xbar_ad_divplat", base + 0x38, 30);
+	clks[IMX8ULP_CLK_DMA1_CH13] = imx_clk_hw_gate("pcc_dma1_ch13", "xbar_ad_divplat", base + 0x3c, 30);
+	clks[IMX8ULP_CLK_DMA1_CH14] = imx_clk_hw_gate("pcc_dma1_ch14", "xbar_ad_divplat", base + 0x40, 30);
+	clks[IMX8ULP_CLK_DMA1_CH15] = imx_clk_hw_gate("pcc_dma1_ch15", "xbar_ad_divplat", base + 0x44, 30);
+	clks[IMX8ULP_CLK_DMA1_CH16] = imx_clk_hw_gate("pcc_dma1_ch16", "xbar_ad_divplat", base + 0x48, 30);
+	clks[IMX8ULP_CLK_DMA1_CH17] = imx_clk_hw_gate("pcc_dma1_ch17", "xbar_ad_divplat", base + 0x4c, 30);
+	clks[IMX8ULP_CLK_DMA1_CH18] = imx_clk_hw_gate("pcc_dma1_ch18", "xbar_ad_divplat", base + 0x50, 30);
+	clks[IMX8ULP_CLK_DMA1_CH19] = imx_clk_hw_gate("pcc_dma1_ch19", "xbar_ad_divplat", base + 0x54, 30);
+	clks[IMX8ULP_CLK_DMA1_CH20] = imx_clk_hw_gate("pcc_dma1_ch20", "xbar_ad_divplat", base + 0x58, 30);
+	clks[IMX8ULP_CLK_DMA1_CH21] = imx_clk_hw_gate("pcc_dma1_ch21", "xbar_ad_divplat", base + 0x5c, 30);
+	clks[IMX8ULP_CLK_DMA1_CH22] = imx_clk_hw_gate("pcc_dma1_ch22", "xbar_ad_divplat", base + 0x60, 30);
+	clks[IMX8ULP_CLK_DMA1_CH23] = imx_clk_hw_gate("pcc_dma1_ch23", "xbar_ad_divplat", base + 0x64, 30);
+	clks[IMX8ULP_CLK_DMA1_CH24] = imx_clk_hw_gate("pcc_dma1_ch24", "xbar_ad_divplat", base + 0x68, 30);
+	clks[IMX8ULP_CLK_DMA1_CH25] = imx_clk_hw_gate("pcc_dma1_ch25", "xbar_ad_divplat", base + 0x6c, 30);
+	clks[IMX8ULP_CLK_DMA1_CH26] = imx_clk_hw_gate("pcc_dma1_ch26", "xbar_ad_divplat", base + 0x70, 30);
+	clks[IMX8ULP_CLK_DMA1_CH27] = imx_clk_hw_gate("pcc_dma1_ch27", "xbar_ad_divplat", base + 0x74, 30);
+	clks[IMX8ULP_CLK_DMA1_CH28] = imx_clk_hw_gate("pcc_dma1_ch28", "xbar_ad_divplat", base + 0x78, 30);
+	clks[IMX8ULP_CLK_DMA1_CH29] = imx_clk_hw_gate("pcc_dma1_ch29", "xbar_ad_divplat", base + 0x7c, 30);
+	clks[IMX8ULP_CLK_DMA1_CH30] = imx_clk_hw_gate("pcc_dma1_ch30", "xbar_ad_divplat", base + 0x80, 30);
+	clks[IMX8ULP_CLK_DMA1_CH31] = imx_clk_hw_gate("pcc_dma1_ch31", "xbar_ad_divplat", base + 0x84, 30);
+	clks[IMX8ULP_CLK_MU0_B] = imx_clk_hw_gate("mu0_b", "xbar_ad_divplat", base + 0x88, 30);
+	clks[IMX8ULP_CLK_MU3_A] = imx_clk_hw_gate("mu3_a", "xbar_ad_divplat", base + 0x8c, 30);
+
+	imx_check_clk_hws(clks, clk_data->num);
+
+	ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, clk_data);
+
+	imx_register_uart_clocks(1);
+
+	return ret;
+}
+
+static int imx8ulp_clk_pcc4_init(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct clk_hw_onecell_data *clk_data;
+	struct clk_hw **clks;
+	void __iomem *base;
+
+	clk_data = devm_kzalloc(dev, struct_size(clk_data, hws, IMX8ULP_CLK_PCC4_END),
+			   GFP_KERNEL);
+	if (!clk_data)
+		return -ENOMEM;
+
+	clk_data->num = IMX8ULP_CLK_PCC4_END;
+	clks = clk_data->hws;
+
+	/* PCC4 */
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (WARN_ON(IS_ERR(base)))
+		return PTR_ERR(base);
+
+	clks[IMX8ULP_CLK_FLEXSPI2] = imx8ulp_clk_hw_composite("flexspi2", pcc4_periph_plat_sels, ARRAY_SIZE(pcc4_periph_plat_sels), true, true, true, base + 0x4, 1);
+	clks[IMX8ULP_CLK_TPM6] = imx8ulp_clk_hw_composite("tpm6", pcc4_periph_bus_sels, ARRAY_SIZE(pcc4_periph_bus_sels), true, true, true, base + 0x8, 1);
+	clks[IMX8ULP_CLK_TPM7] = imx8ulp_clk_hw_composite("tpm7", pcc4_periph_bus_sels, ARRAY_SIZE(pcc4_periph_bus_sels), true, true, true, base + 0xc, 1);
+	clks[IMX8ULP_CLK_LPI2C6] = imx8ulp_clk_hw_composite("lpi2c6", pcc4_periph_bus_sels, ARRAY_SIZE(pcc4_periph_bus_sels), true, true, true, base + 0x10, 1);
+	clks[IMX8ULP_CLK_LPI2C7] = imx8ulp_clk_hw_composite("lpi2c7", pcc4_periph_bus_sels, ARRAY_SIZE(pcc4_periph_bus_sels), true, true, true, base + 0x14, 1);
+	clks[IMX8ULP_CLK_LPUART6] = imx8ulp_clk_hw_composite("lpuart6", pcc4_periph_bus_sels, ARRAY_SIZE(pcc4_periph_bus_sels), true, true, true, base + 0x18, 1);
+	clks[IMX8ULP_CLK_LPUART7] = imx8ulp_clk_hw_composite("lpuart7", pcc4_periph_bus_sels, ARRAY_SIZE(pcc4_periph_bus_sels), true, true, true, base + 0x1c, 1);
+	clks[IMX8ULP_CLK_SAI4] = imx8ulp_clk_hw_composite("sai4", xbar_divbus, 1, false, false, true, base + 0x20, 1); /* sai ipg, NOT from sai sel */
+	clks[IMX8ULP_CLK_SAI5] = imx8ulp_clk_hw_composite("sai5", xbar_divbus, 1, false, false, true, base + 0x24, 1); /* sai ipg */
+	clks[IMX8ULP_CLK_PCTLE] = imx_clk_hw_gate("pctle", "xbar_divbus", base + 0x28, 30);
+	clks[IMX8ULP_CLK_PCTLF] = imx_clk_hw_gate("pctlf", "xbar_divbus", base + 0x2c, 30);
+	clks[IMX8ULP_CLK_USDHC0] = imx8ulp_clk_hw_composite("usdhc0", pcc4_periph_plat_sels, ARRAY_SIZE(pcc4_periph_plat_sels), true, false, true, base + 0x34, 1);
+	clks[IMX8ULP_CLK_USDHC1] = imx8ulp_clk_hw_composite("usdhc1", pcc4_periph_plat_sels, ARRAY_SIZE(pcc4_periph_plat_sels), true, false, true, base + 0x38, 1);
+	clks[IMX8ULP_CLK_USDHC2] = imx8ulp_clk_hw_composite("usdhc2", pcc4_periph_plat_sels, ARRAY_SIZE(pcc4_periph_plat_sels), true, false, true, base + 0x3c, 1);
+	clks[IMX8ULP_CLK_USB0] = imx8ulp_clk_hw_composite("usb0", nic_per_divplat, 1, false, false, true, base + 0x40, 1);
+	clks[IMX8ULP_CLK_USB0_PHY] = imx8ulp_clk_hw_composite("usb0_phy", xbar_divbus, 1, false, false, true, base + 0x44, 1);
+	clks[IMX8ULP_CLK_USB1] = imx8ulp_clk_hw_composite("usb1", nic_per_divplat, 1, false, false, true, base + 0x48, 1);
+	clks[IMX8ULP_CLK_USB1_PHY] = imx8ulp_clk_hw_composite("usb1_phy", xbar_divbus, 1, false, false, true, base + 0x4c, 1);
+	clks[IMX8ULP_CLK_USB_XBAR] = imx_clk_hw_gate("usb_xbar", "xbar_divbus", base + 0x50, 30);
+	clks[IMX8ULP_CLK_ENET] = imx8ulp_clk_hw_composite("enet", nic_per_divplat, 1, false, false, true, base + 0x54, 1);
+	clks[IMX8ULP_CLK_RGPIOE] = imx_clk_hw_gate("rgpioe", "nic_per_divplat", base + 0x78, 30);
+	clks[IMX8ULP_CLK_RGPIOF] = imx_clk_hw_gate("rgpiof", "nic_per_divplat", base + 0x7c, 30);
+
+	imx_check_clk_hws(clks, clk_data->num);
+
+	return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, clk_data);
+}
+
+static int imx8ulp_clk_pcc5_init(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct clk_hw_onecell_data *clk_data;
+	struct clk_hw **clks;
+	void __iomem *base;
+
+	clk_data = devm_kzalloc(dev, struct_size(clk_data, hws, IMX8ULP_CLK_PCC5_END),
+			   GFP_KERNEL);
+	if (!clk_data)
+		return -ENOMEM;
+
+	clk_data->num = IMX8ULP_CLK_PCC5_END;
+	clks = clk_data->hws;
+
+	/* PCC5 */
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (WARN_ON(IS_ERR(base)))
+		return PTR_ERR(base);
+
+	clks[IMX8ULP_CLK_DMA2_MP] = imx_clk_hw_gate("pcc_dma2_mp", "lpav_axi_div", base + 0x0, 30);
+	clks[IMX8ULP_CLK_DMA2_CH0] = imx_clk_hw_gate("pcc_dma2_ch0", "lpav_axi_div", base + 0x4, 30);
+	clks[IMX8ULP_CLK_DMA2_CH1] = imx_clk_hw_gate("pcc_dma2_ch1", "lpav_axi_div", base + 0x8, 30);
+	clks[IMX8ULP_CLK_DMA2_CH2] = imx_clk_hw_gate("pcc_dma2_ch2", "lpav_axi_div", base + 0xc, 30);
+	clks[IMX8ULP_CLK_DMA2_CH3] = imx_clk_hw_gate("pcc_dma2_ch3", "lpav_axi_div", base + 0x10, 30);
+	clks[IMX8ULP_CLK_DMA2_CH4] = imx_clk_hw_gate("pcc_dma2_ch4", "lpav_axi_div", base + 0x14, 30);
+	clks[IMX8ULP_CLK_DMA2_CH5] = imx_clk_hw_gate("pcc_dma2_ch5", "lpav_axi_div", base + 0x18, 30);
+	clks[IMX8ULP_CLK_DMA2_CH6] = imx_clk_hw_gate("pcc_dma2_ch6", "lpav_axi_div", base + 0x1c, 30);
+	clks[IMX8ULP_CLK_DMA2_CH7] = imx_clk_hw_gate("pcc_dma2_ch7", "lpav_axi_div", base + 0x20, 30);
+	clks[IMX8ULP_CLK_DMA2_CH8] = imx_clk_hw_gate("pcc_dma2_ch8", "lpav_axi_div", base + 0x24, 30);
+	clks[IMX8ULP_CLK_DMA2_CH9] = imx_clk_hw_gate("pcc_dma2_ch9", "lpav_axi_div", base + 0x28, 30);
+	clks[IMX8ULP_CLK_DMA2_CH10] = imx_clk_hw_gate("pcc_dma2_ch10", "lpav_axi_div", base + 0x2c, 30);
+	clks[IMX8ULP_CLK_DMA2_CH11] = imx_clk_hw_gate("pcc_dma2_ch11", "lpav_axi_div", base + 0x30, 30);
+	clks[IMX8ULP_CLK_DMA2_CH12] = imx_clk_hw_gate("pcc_dma2_ch12", "lpav_axi_div", base + 0x34, 30);
+	clks[IMX8ULP_CLK_DMA2_CH13] = imx_clk_hw_gate("pcc_dma2_ch13", "lpav_axi_div", base + 0x38, 30);
+	clks[IMX8ULP_CLK_DMA2_CH14] = imx_clk_hw_gate("pcc_dma2_ch14", "lpav_axi_div", base + 0x3c, 30);
+	clks[IMX8ULP_CLK_DMA2_CH15] = imx_clk_hw_gate("pcc_dma2_ch15", "lpav_axi_div", base + 0x40, 30);
+	clks[IMX8ULP_CLK_DMA2_CH16] = imx_clk_hw_gate("pcc_dma2_ch16", "lpav_axi_div", base + 0x44, 30);
+	clks[IMX8ULP_CLK_DMA2_CH17] = imx_clk_hw_gate("pcc_dma2_ch17", "lpav_axi_div", base + 0x48, 30);
+	clks[IMX8ULP_CLK_DMA2_CH18] = imx_clk_hw_gate("pcc_dma2_ch18", "lpav_axi_div", base + 0x4c, 30);
+	clks[IMX8ULP_CLK_DMA2_CH19] = imx_clk_hw_gate("pcc_dma2_ch19", "lpav_axi_div", base + 0x50, 30);
+	clks[IMX8ULP_CLK_DMA2_CH20] = imx_clk_hw_gate("pcc_dma2_ch20", "lpav_axi_div", base + 0x54, 30);
+	clks[IMX8ULP_CLK_DMA2_CH21] = imx_clk_hw_gate("pcc_dma2_ch21", "lpav_axi_div", base + 0x58, 30);
+	clks[IMX8ULP_CLK_DMA2_CH22] = imx_clk_hw_gate("pcc_dma2_ch22", "lpav_axi_div", base + 0x5c, 30);
+	clks[IMX8ULP_CLK_DMA2_CH23] = imx_clk_hw_gate("pcc_dma2_ch23", "lpav_axi_div", base + 0x60, 30);
+	clks[IMX8ULP_CLK_DMA2_CH24] = imx_clk_hw_gate("pcc_dma2_ch24", "lpav_axi_div", base + 0x64, 30);
+	clks[IMX8ULP_CLK_DMA2_CH25] = imx_clk_hw_gate("pcc_dma2_ch25", "lpav_axi_div", base + 0x68, 30);
+	clks[IMX8ULP_CLK_DMA2_CH26] = imx_clk_hw_gate("pcc_dma2_ch26", "lpav_axi_div", base + 0x6c, 30);
+	clks[IMX8ULP_CLK_DMA2_CH27] = imx_clk_hw_gate("pcc_dma2_ch27", "lpav_axi_div", base + 0x70, 30);
+	clks[IMX8ULP_CLK_DMA2_CH28] = imx_clk_hw_gate("pcc_dma2_ch28", "lpav_axi_div", base + 0x74, 30);
+	clks[IMX8ULP_CLK_DMA2_CH29] = imx_clk_hw_gate("pcc_dma2_ch29", "lpav_axi_div", base + 0x78, 30);
+	clks[IMX8ULP_CLK_DMA2_CH30] = imx_clk_hw_gate("pcc_dma2_ch30", "lpav_axi_div", base + 0x7c, 30);
+	clks[IMX8ULP_CLK_DMA2_CH31] = imx_clk_hw_gate("pcc_dma2_ch31", "lpav_axi_div", base + 0x80, 30);
+
+	clks[IMX8ULP_CLK_AVD_SIM] = imx_clk_hw_gate("avd_sim", "lpav_bus_div", base + 0x94, 30);
+	clks[IMX8ULP_CLK_TPM8] = imx8ulp_clk_hw_composite("tpm8", pcc5_periph_bus_sels, ARRAY_SIZE(pcc5_periph_bus_sels), true, true, true, base + 0xa0, 1);
+	clks[IMX8ULP_CLK_MU2_B] = imx_clk_hw_gate("mu2_b", "lpav_bus_div", base + 0x84, 30);
+	clks[IMX8ULP_CLK_MU3_B] = imx_clk_hw_gate("mu3_b", "lpav_bus_div", base + 0x88, 30);
+	clks[IMX8ULP_CLK_SAI6] = imx8ulp_clk_hw_composite("sai6", lpav_bus_div, 1, false, false, true, base + 0xa4, 1);
+	clks[IMX8ULP_CLK_SAI7] = imx8ulp_clk_hw_composite("sai7", lpav_bus_div, 1, false, false, true, base + 0xa8, 1);
+	clks[IMX8ULP_CLK_SPDIF] = imx8ulp_clk_hw_composite("spdif", lpav_bus_div, 1, false, false, true, base + 0xac, 1);
+	clks[IMX8ULP_CLK_ISI] = imx8ulp_clk_hw_composite("isi", lpav_axi_div, 1, false, false, true, base + 0xb0, 1);
+	clks[IMX8ULP_CLK_CSI_REGS] = imx8ulp_clk_hw_composite("csi_regs", lpav_bus_div, 1, false, false, true, base + 0xb4, 1);
+	clks[IMX8ULP_CLK_CSI] = imx8ulp_clk_hw_composite("csi", pcc5_periph_plat_sels, ARRAY_SIZE(pcc5_periph_plat_sels), true, true, true, base + 0xbc, 1);
+	clks[IMX8ULP_CLK_DSI] = imx8ulp_clk_hw_composite("dsi", pcc5_periph_plat_sels, ARRAY_SIZE(pcc5_periph_plat_sels), true, true, true, base + 0xc0, 1);
+	clks[IMX8ULP_CLK_WDOG5] = imx8ulp_clk_hw_composite("wdog5", pcc5_periph_bus_sels, ARRAY_SIZE(pcc5_periph_bus_sels), true, true, true, base + 0xc8, 1);
+	clks[IMX8ULP_CLK_EPDC] = imx8ulp_clk_hw_composite("epdc", pcc5_periph_plat_sels, ARRAY_SIZE(pcc5_periph_plat_sels), true, true, true, base + 0xcc, 1);
+	clks[IMX8ULP_CLK_PXP] = imx8ulp_clk_hw_composite("pxp", lpav_axi_div, 1, false, false, true, base + 0xd0, 1);
+	clks[IMX8ULP_CLK_GPU2D] = imx8ulp_clk_hw_composite("gpu2d", pcc5_periph_plat_sels, ARRAY_SIZE(pcc5_periph_plat_sels), true, true, true, base + 0xf0, 1);
+	clks[IMX8ULP_CLK_GPU3D] = imx8ulp_clk_hw_composite("gpu3d", pcc5_periph_plat_sels, ARRAY_SIZE(pcc5_periph_plat_sels), true, true, true, base + 0xf4, 1);
+	clks[IMX8ULP_CLK_DC_NANO] = imx8ulp_clk_hw_composite("dc_nano", pcc5_periph_plat_sels, ARRAY_SIZE(pcc5_periph_plat_sels), true, true, true, base + 0xf8, 1);
+	clks[IMX8ULP_CLK_CSI_CLK_UI] = imx8ulp_clk_hw_composite("csi_clk_ui", pcc5_periph_plat_sels, ARRAY_SIZE(pcc5_periph_plat_sels), true, true, true, base + 0x10c, 1);
+	clks[IMX8ULP_CLK_CSI_CLK_ESC] = imx8ulp_clk_hw_composite("csi_clk_esc", pcc5_periph_plat_sels, ARRAY_SIZE(pcc5_periph_plat_sels), true, true, true, base + 0x110, 1);
+	clks[IMX8ULP_CLK_RGPIOD] = imx_clk_hw_gate("rgpiod", "lpav_axi_div", base + 0x114, 30);
+	clks[IMX8ULP_CLK_DSI_TX_ESC] = imx_clk_hw_fixed_factor("mipi_dsi_tx_esc", "dsi", 1, 4);
+
+	imx_check_clk_hws(clks, clk_data->num);
+
+	return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, clk_data);
+}
+
+static int imx8ulp_clk_probe(struct platform_device *pdev)
+{
+	int (*probe)(struct platform_device *pdev);
+
+	probe = of_device_get_match_data(&pdev->dev);
+
+	if (probe)
+		return probe(pdev);
+
+	return 0;
+}
+
+static const struct of_device_id imx8ulp_clk_dt_ids[] = {
+	{ .compatible = "fsl,imx8ulp-pcc3", .data = imx8ulp_clk_pcc3_init },
+	{ .compatible = "fsl,imx8ulp-pcc4", .data = imx8ulp_clk_pcc4_init },
+	{ .compatible = "fsl,imx8ulp-pcc5", .data = imx8ulp_clk_pcc5_init },
+	{ .compatible = "fsl,imx8ulp-cgc2", .data = imx8ulp_clk_cgc2_init },
+	{ .compatible = "fsl,imx8ulp-cgc1", .data = imx8ulp_clk_cgc1_init },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, imx8ulp_clk_dt_ids);
+
+static struct platform_driver imx8ulp_clk_driver = {
+	.probe	= imx8ulp_clk_probe,
+	.driver = {
+		.name		= KBUILD_MODNAME,
+		.of_match_table	= imx8ulp_clk_dt_ids,
+	},
+};
+module_platform_driver(imx8ulp_clk_driver);
+
+MODULE_AUTHOR("Peng Fan <[email protected]>");
+MODULE_DESCRIPTION("NXP i.MX8ULP clock driver");
+MODULE_LICENSE("GPL v2");
Signature · 1 line
2.26.2
author
#20 lore raw

PATCH v3 9/9 clk: imx: Add the pcc reset controller support on imx8ulp

In reply to Jacky Bai

On i.MX8ULP, for some of the PCCs, it has a peripheral SW RST bit resides in the same registers as the clock controller. So add this SW RST controller support alongs with the pcc clock initialization.

the reset and clock shared the same register, to avoid accessing the same register by reset control and clock control concurrently, locking is necessary, so reuse the imx_ccm_lock spinlock to simplify the code.

---
v3 changes:
- remove the explict selection of 'RESET_CONTROLLER' in kconfig
- add some comments for the spinlock of reset driver

v2 changes:
- add 'Suggested-by' as suggested by Victor Liu

---
 drivers/clk/imx/clk-composite-7ulp.c |  10 +++
 drivers/clk/imx/clk-imx8ulp.c        | 116 ++++++++++++++++++++++++++-
 2 files changed, 123 insertions(+), 3 deletions(-)
drivers/clk/imx/clk-composite-7ulp.c +10 -0
index 9ce8c630ee32..89106de16a3f 100644
@@ -29,6 +29,7 @@
 static int pcc_gate_enable(struct clk_hw *hw)
 {
 	struct clk_gate *gate = to_clk_gate(hw);
+	unsigned long flags;
 	u32 val;
 	int ret;
 
@@ -36,6 +37,7 @@ static int pcc_gate_enable(struct clk_hw *hw)
 	if (ret)
 		return ret;
 
+	spin_lock_irqsave(gate->lock, flags);
 	/*
 	 * release the sw reset for peripherals associated with
 	 * with this pcc clock.
@@ -44,6 +46,8 @@ static int pcc_gate_enable(struct clk_hw *hw)
 	val |= SW_RST;
 	writel(val, gate->reg);
 
+	spin_unlock_irqrestore(gate->lock, flags);
+
 	return 0;
 }
 
@@ -84,6 +88,8 @@ static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 		mux->reg = reg;
 		mux->shift = PCG_PCS_SHIFT;
 		mux->mask = PCG_PCS_MASK;
+		if (has_swrst)
+			mux->lock = &imx_ccm_lock;
 	}
 
 	if (rate_present) {
@@ -101,6 +107,8 @@ static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 		fd->nwidth = PCG_PCD_WIDTH;
 		fd->nmask = PCG_PCD_MASK;
 		fd->flags = CLK_FRAC_DIVIDER_ZERO_BASED;
+		if (has_swrst)
+			fd->lock = &imx_ccm_lock;
 	}
 
 	if (gate_present) {
@@ -113,6 +121,8 @@ static struct clk_hw *imx_ulp_clk_hw_composite(const char *name,
 		gate_hw = &gate->hw;
 		gate->reg = reg;
 		gate->bit_idx = PCG_CGC_SHIFT;
+		if (has_swrst)
+			gate->lock = &imx_ccm_lock;
 		/*
 		 * make sure clock is gated during clock tree initialization,
 		 * the HW ONLY allow clock parent/rate changed with clock gated,
drivers/clk/imx/clk-imx8ulp.c +113 -3

161 lines not on this page · raw message

Signature · 1 line
2.26.2
#21 lore raw

Re: [PATCH v3 9/9] clk: imx: Add the pcc reset controller support on imx8ulp

Quoted 36 lines · Jacky Bai
drivers/clk/imx/clk-imx8ulp.c +21 -0
index 6aad04114658..6699437e17b8 100644
@@ -9,6 +9,7 @@
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/reset-controller.h>
 #include <linux/slab.h>
 
 #include "clk.h"
@@ -48,6 +49,99 @@ static const char * const nic_per_divplat[] = { "nic_per_divplat" };
 static const char * const lpav_axi_div[] = { "lpav_axi_div" };
 static const char * const lpav_bus_div[] = { "lpav_bus_div" };
 
+struct pcc_reset_dev {
+	void __iomem *base;
+	struct reset_controller_dev rcdev;
+	const u32 *resets;
+	/* Set to imx_ccm_lock to protect register access shared with clock control */
+	spinlock_t *lock;
+};
+
+#define PCC_SW_RST	BIT(28)
+#define to_pcc_reset_dev(_rcdev)	container_of(_rcdev, struct pcc_reset_dev, rcdev)
+
+static const u32 pcc3_resets[] = {
+	0xa8, 0xac, 0xc8, 0xcc, 0xd0,
+	0xd4, 0xd8, 0xdc, 0xe0, 0xe4,
+	0xe8, 0xec, 0xf0
+};
+
+static const u32 pcc4_resets[] = {
+	0x4, 0x8, 0xc, 0x10, 0x14,
+	0x18, 0x1c, 0x20, 0x24, 0x34,

drivers/clk/imx/clk-imx8ulp.c static const char * const nic_per_divplat[] = { "nic_per_divplat" }; · line 81

Quoted 10 lines
drivers/clk/imx/clk-imx8ulp.c +10 -0
+	0x38, 0x3c, 0x40, 0x44, 0x48,
+	0x4c, 0x54
+};
+
+static const u32 pcc5_resets[] = {
+	0xa0, 0xa4, 0xa8, 0xac, 0xb0,
+	0xb4, 0xbc, 0xc0, 0xc8, 0xcc,
+	0xd0, 0xf0, 0xf4, 0xf8
+};
+

I believe this could be avoided entirely by having something like:

PCCx_RESETS_OFFSET + (index * 4)

and then:

#define PCC3_RESETS_OFFSET 0xa8
#define PCC4_RESETS_OFFSET 0x4
#define PCC5_RESETS_OFFSET 0xa0

#define PCC3_RESETS_NUM 13
#define PCC4_RESETS_NUM 17
#define PCC5_RESETS_NUM 14

Then we could pass on the PCCx_RESETS_OFFSET and the PCCx_RESETS_NUM and that's it.

Quoted 63 lines
drivers/clk/imx/clk-imx8ulp.c +63 -0
+static int imx8ulp_pcc_assert(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	struct pcc_reset_dev *pcc_reset = to_pcc_reset_dev(rcdev);
+	u32 offset = pcc_reset->resets[id];
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(pcc_reset->lock, flags);
+
+	val = readl(pcc_reset->base + offset);
+	val &= ~PCC_SW_RST;
+	writel(val, pcc_reset->base + offset);
+
+	spin_unlock_irqrestore(pcc_reset->lock, flags);
+
+	return 0;
+}
+
+static int imx8ulp_pcc_deassert(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	struct pcc_reset_dev *pcc_reset = to_pcc_reset_dev(rcdev);
+	u32 offset = pcc_reset->resets[id];
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(pcc_reset->lock, flags);
+
+	val = readl(pcc_reset->base + offset);
+	val |= PCC_SW_RST;
+	writel(val, pcc_reset->base + offset);
+
+	spin_unlock_irqrestore(pcc_reset->lock, flags);
+
+	return 0;
+}
+
+static const struct reset_control_ops imx8ulp_pcc_reset_ops = {
+	.assert = imx8ulp_pcc_assert,
+	.deassert = imx8ulp_pcc_deassert,
+};
+
+static int imx8ulp_pcc_reset_init(struct platform_device *pdev, void __iomem *base,
+	 const u32 *resets, unsigned int nr_resets)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	struct pcc_reset_dev *pcc_reset;
+
+	pcc_reset = devm_kzalloc(dev, sizeof(*pcc_reset), GFP_KERNEL);
+	if (!pcc_reset)
+		return -ENOMEM;
+
+	pcc_reset->base = base;
+	pcc_reset->lock = &imx_ccm_lock;
+	pcc_reset->resets = resets;
+	pcc_reset->rcdev.owner = THIS_MODULE;
+	pcc_reset->rcdev.nr_resets = nr_resets;
+	pcc_reset->rcdev.ops = &imx8ulp_pcc_reset_ops;
+	pcc_reset->rcdev.of_node = np;
+
+	return devm_reset_controller_register(dev, &pcc_reset->rcdev);
+}
+

...

Quoted 3 lines
Signature · 1 line
2.26.2
author
#22 lore raw

RE: [PATCH v3 9/9] clk: imx: Add the pcc reset controller support on imx8ulp

Quoted 65 lines

Subject: Re: [PATCH v3 9/9] clk: imx: Add the pcc reset controller support on imx8ulp

Quoted 14 lines · Jacky Bai
(quoted diff) +0 -0

b/drivers/clk/imx/clk-imx8ulp.c index 6aad04114658..6699437e17b8 100644

drivers/clk/imx/clk-imx8ulp.c +1 -0
@@ -9,6 +9,7 @@
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/reset-controller.h>
 #include <linux/slab.h>
 
 #include "clk.h"

drivers/clk/imx/clk-imx8ulp.c static const char * const nic_per_divplat[] = { · line 57

Quoted 9 lines
drivers/clk/imx/clk-imx8ulp.c +5 -0
@@ -48,6 +49,99 @@ static const char * const nic_per_divplat[] = {
 "nic_per_divplat" };  static const char * const lpav_axi_div[] = {
 "lpav_axi_div" };  static const char * const lpav_bus_div[] = {
 "lpav_bus_div" };
 
+struct pcc_reset_dev {
+	void __iomem *base;
+	struct reset_controller_dev rcdev;
+	const u32 *resets;
+	/* Set to imx_ccm_lock to protect register access shared with clock

control */

drivers/clk/imx/clk-imx8ulp.c static const char * const nic_per_divplat[] = { "nic_per_divplat" };

Quoted 5 lines
drivers/clk/imx/clk-imx8ulp.c +5 -0
+	spinlock_t *lock;
+};
+
+#define PCC_SW_RST	BIT(28)
+#define to_pcc_reset_dev(_rcdev)	container_of(_rcdev, struct

pcc_reset_dev, rcdev)

Quoted 10 lines
drivers/clk/imx/clk-imx8ulp.c +10 -0
+
+static const u32 pcc3_resets[] = {
+	0xa8, 0xac, 0xc8, 0xcc, 0xd0,
+	0xd4, 0xd8, 0xdc, 0xe0, 0xe4,
+	0xe8, 0xec, 0xf0
+};
+
+static const u32 pcc4_resets[] = {
+	0x4, 0x8, 0xc, 0x10, 0x14,
+	0x18, 0x1c, 0x20, 0x24, 0x34,

drivers/clk/imx/clk-imx8ulp.c static const char * const nic_per_divplat[] = { "nic_per_divplat" }; · line 81

Quoted 10 lines
drivers/clk/imx/clk-imx8ulp.c +10 -0
+	0x38, 0x3c, 0x40, 0x44, 0x48,
+	0x4c, 0x54
+};
+
+static const u32 pcc5_resets[] = {
+	0xa0, 0xa4, 0xa8, 0xac, 0xb0,
+	0xb4, 0xbc, 0xc0, 0xc8, 0xcc,
+	0xd0, 0xf0, 0xf4, 0xf8
+};
+

I believe this could be avoided entirely by having something like:

PCCx_RESETS_OFFSET + (index * 4)

and then:

#define PCC3_RESETS_OFFSET 0xa8
#define PCC4_RESETS_OFFSET 0x4
#define PCC5_RESETS_OFFSET 0xa0

Quoted 7 lines

#define PCC3_RESETS_NUM 13
#define PCC4_RESETS_NUM 17
#define PCC5_RESETS_NUM 14

Then we could pass on the PCCx_RESETS_OFFSET and the PCCx_RESETS_NUM and that's it.

As you can see that the PCC offset that has reset is not consecutive in the register region. So it will introduce hole in the index. And we can NOT use linear formula to calculate the offset directly.

BR
Jacky Bai

Quoted 68 lines
Quoted 32 lines
drivers/clk/imx/clk-imx8ulp.c +32 -0
+static int imx8ulp_pcc_assert(struct reset_controller_dev *rcdev,
+unsigned long id) {
+	struct pcc_reset_dev *pcc_reset = to_pcc_reset_dev(rcdev);
+	u32 offset = pcc_reset->resets[id];
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(pcc_reset->lock, flags);
+
+	val = readl(pcc_reset->base + offset);
+	val &= ~PCC_SW_RST;
+	writel(val, pcc_reset->base + offset);
+
+	spin_unlock_irqrestore(pcc_reset->lock, flags);
+
+	return 0;
+}
+
+static int imx8ulp_pcc_deassert(struct reset_controller_dev *rcdev,
+unsigned long id) {
+	struct pcc_reset_dev *pcc_reset = to_pcc_reset_dev(rcdev);
+	u32 offset = pcc_reset->resets[id];
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(pcc_reset->lock, flags);
+
+	val = readl(pcc_reset->base + offset);
+	val |= PCC_SW_RST;
+	writel(val, pcc_reset->base + offset);
+
+	spin_unlock_irqrestore(pcc_reset->lock, flags);

drivers/clk/imx/clk-imx8ulp.c static const char * const nic_per_divplat[] = { "nic_per_divplat" };

Quoted 10 lines
drivers/clk/imx/clk-imx8ulp.c +10 -0
+
+	return 0;
+}
+
+static const struct reset_control_ops imx8ulp_pcc_reset_ops = {
+	.assert = imx8ulp_pcc_assert,
+	.deassert = imx8ulp_pcc_deassert,
+};
+
+static int imx8ulp_pcc_reset_init(struct platform_device *pdev, void

__iomem *base,

Quoted 19 lines
drivers/clk/imx/clk-imx8ulp.c +19 -0
+	 const u32 *resets, unsigned int nr_resets) {
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	struct pcc_reset_dev *pcc_reset;
+
+	pcc_reset = devm_kzalloc(dev, sizeof(*pcc_reset), GFP_KERNEL);
+	if (!pcc_reset)
+		return -ENOMEM;
+
+	pcc_reset->base = base;
+	pcc_reset->lock = &imx_ccm_lock;
+	pcc_reset->resets = resets;
+	pcc_reset->rcdev.owner = THIS_MODULE;
+	pcc_reset->rcdev.nr_resets = nr_resets;
+	pcc_reset->rcdev.ops = &imx8ulp_pcc_reset_ops;
+	pcc_reset->rcdev.of_node = np;
+
+	return devm_reset_controller_register(dev, &pcc_reset->rcdev); }
+

...

Quoted 3 lines

--
2.26.2

Reviewed-by
#23 lore raw

Re: [PATCH v3 9/9] clk: imx: Add the pcc reset controller support on imx8ulp

Quoted 69 lines · Jacky Bai
Quoted 69 lines

Subject: Re: [PATCH v3 9/9] clk: imx: Add the pcc reset controller support on imx8ulp

Quoted 14 lines · Jacky Bai
(quoted diff) +0 -0

b/drivers/clk/imx/clk-imx8ulp.c index 6aad04114658..6699437e17b8 100644

drivers/clk/imx/clk-imx8ulp.c +1 -0
@@ -9,6 +9,7 @@
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/reset-controller.h>
 #include <linux/slab.h>
 
 #include "clk.h"

drivers/clk/imx/clk-imx8ulp.c static const char * const nic_per_divplat[] = { · line 57

Quoted 9 lines
drivers/clk/imx/clk-imx8ulp.c +5 -0
@@ -48,6 +49,99 @@ static const char * const nic_per_divplat[] = {
 "nic_per_divplat" };  static const char * const lpav_axi_div[] = {
 "lpav_axi_div" };  static const char * const lpav_bus_div[] = {
 "lpav_bus_div" };
 
+struct pcc_reset_dev {
+	void __iomem *base;
+	struct reset_controller_dev rcdev;
+	const u32 *resets;
+	/* Set to imx_ccm_lock to protect register access shared with clock

control */

drivers/clk/imx/clk-imx8ulp.c static const char * const nic_per_divplat[] = { "nic_per_divplat" };

Quoted 5 lines
drivers/clk/imx/clk-imx8ulp.c +5 -0
+	spinlock_t *lock;
+};
+
+#define PCC_SW_RST	BIT(28)
+#define to_pcc_reset_dev(_rcdev)	container_of(_rcdev, struct

pcc_reset_dev, rcdev)

Quoted 10 lines
drivers/clk/imx/clk-imx8ulp.c +10 -0
+
+static const u32 pcc3_resets[] = {
+	0xa8, 0xac, 0xc8, 0xcc, 0xd0,
+	0xd4, 0xd8, 0xdc, 0xe0, 0xe4,
+	0xe8, 0xec, 0xf0
+};
+
+static const u32 pcc4_resets[] = {
+	0x4, 0x8, 0xc, 0x10, 0x14,
+	0x18, 0x1c, 0x20, 0x24, 0x34,

drivers/clk/imx/clk-imx8ulp.c static const char * const nic_per_divplat[] = { "nic_per_divplat" }; · line 81

Quoted 10 lines
drivers/clk/imx/clk-imx8ulp.c +10 -0
+	0x38, 0x3c, 0x40, 0x44, 0x48,
+	0x4c, 0x54
+};
+
+static const u32 pcc5_resets[] = {
+	0xa0, 0xa4, 0xa8, 0xac, 0xb0,
+	0xb4, 0xbc, 0xc0, 0xc8, 0xcc,
+	0xd0, 0xf0, 0xf4, 0xf8
+};
+

I believe this could be avoided entirely by having something like:

PCCx_RESETS_OFFSET + (index * 4)

and then:

#define PCC3_RESETS_OFFSET 0xa8
#define PCC4_RESETS_OFFSET 0x4
#define PCC5_RESETS_OFFSET 0xa0

#define PCC3_RESETS_NUM 13
#define PCC4_RESETS_NUM 17
#define PCC5_RESETS_NUM 14

Quoted 7 lines
Quoted 3 lines

Then we could pass on the PCCx_RESETS_OFFSET and the PCCx_RESETS_NUM and that's it.

As you can see that the PCC offset that has reset is not consecutive in the register region. So it will introduce hole in the index. And we can NOT use linear formula to calculate the offset directly.

You are right, they don't seem to be consecutive, on a closer look.

I don't have any other comments, so:

Quoted 71 lines

BR
Jacky Bai

Quoted 68 lines
Quoted 32 lines
drivers/clk/imx/clk-imx8ulp.c +32 -0
+static int imx8ulp_pcc_assert(struct reset_controller_dev *rcdev,
+unsigned long id) {
+	struct pcc_reset_dev *pcc_reset = to_pcc_reset_dev(rcdev);
+	u32 offset = pcc_reset->resets[id];
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(pcc_reset->lock, flags);
+
+	val = readl(pcc_reset->base + offset);
+	val &= ~PCC_SW_RST;
+	writel(val, pcc_reset->base + offset);
+
+	spin_unlock_irqrestore(pcc_reset->lock, flags);
+
+	return 0;
+}
+
+static int imx8ulp_pcc_deassert(struct reset_controller_dev *rcdev,
+unsigned long id) {
+	struct pcc_reset_dev *pcc_reset = to_pcc_reset_dev(rcdev);
+	u32 offset = pcc_reset->resets[id];
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(pcc_reset->lock, flags);
+
+	val = readl(pcc_reset->base + offset);
+	val |= PCC_SW_RST;
+	writel(val, pcc_reset->base + offset);
+
+	spin_unlock_irqrestore(pcc_reset->lock, flags);

drivers/clk/imx/clk-imx8ulp.c static const char * const nic_per_divplat[] = { "nic_per_divplat" };

Quoted 10 lines
drivers/clk/imx/clk-imx8ulp.c +10 -0
+
+	return 0;
+}
+
+static const struct reset_control_ops imx8ulp_pcc_reset_ops = {
+	.assert = imx8ulp_pcc_assert,
+	.deassert = imx8ulp_pcc_deassert,
+};
+
+static int imx8ulp_pcc_reset_init(struct platform_device *pdev, void

__iomem *base,

Quoted 19 lines
drivers/clk/imx/clk-imx8ulp.c +19 -0
+	 const u32 *resets, unsigned int nr_resets) {
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	struct pcc_reset_dev *pcc_reset;
+
+	pcc_reset = devm_kzalloc(dev, sizeof(*pcc_reset), GFP_KERNEL);
+	if (!pcc_reset)
+		return -ENOMEM;
+
+	pcc_reset->base = base;
+	pcc_reset->lock = &imx_ccm_lock;
+	pcc_reset->resets = resets;
+	pcc_reset->rcdev.owner = THIS_MODULE;
+	pcc_reset->rcdev.nr_resets = nr_resets;
+	pcc_reset->rcdev.ops = &imx8ulp_pcc_reset_ops;
+	pcc_reset->rcdev.of_node = np;
+
+	return devm_reset_controller_register(dev, &pcc_reset->rcdev); }
+

...

Quoted 3 lines

--
2.26.2

#24 lore raw
In reply to Jacky Bai
Quoted 6 lines · Jacky Bai

This patchset adds the clock & reset driver support for i.MX8ULP. For some of the PCC slot, As there is a SWRST control bit share the same pcc register for peripheral reset ccontrol. To simplify the case, register the pcc reset controller driver when pcc clock driver is registered.

Quoted 6 lines

Patch 1/9 for the dt-bindings part is send out for review previously with the dts patchset:
https://patchwork.kernel.org/project/linux-arm-kernel/cover/[email protected]/

Shawn suggests to send out the clock driver part firstly, so this patch is included in this patchset for now.

Usually, the clock patches need to be sent to linux-clk mailing list too.

Quoted 43 lines

v3 changes:
- split the clock dt schema file into two file, one for pcc, one for cgc

v2 changes:
- remove the useless clocks & clock-names from the dt-binding doc
- remove the redundant fixed clock register.

Anson Huang (1):
clk: imx: disable i.mx7ulp composite clock during initialization

Jacky Bai (8):
dt-bindings: clock: Add imx8ulp clock support
clk: imx: Update the pllv4 to support imx8ulp
clk: imx: Update the compsite driver to support imx8ulp
clk: imx: Add 'CLK_SET_RATE_NO_REPARENT' for composite-7ulp
clk: imx: disable the pfd when set pfdv2 clock rate
clk: imx: Update the pfdv2 for 8ulp specific support
clk: imx: Add clock driver for imx8ulp
clk: imx: Add the pcc reset controller support on imx8ulp

 .../bindings/clock/imx8ulp-cgc-clock.yaml     |  43 ++
 .../bindings/clock/imx8ulp-pcc-clock.yaml     |  50 ++
 drivers/clk/imx/Kconfig                       |   6 +
 drivers/clk/imx/Makefile                      |   2 +
 drivers/clk/imx/clk-composite-7ulp.c          |  87 ++-
 drivers/clk/imx/clk-imx7ulp.c                 |  20 +-
 drivers/clk/imx/clk-imx8ulp.c                 | 569 ++++++++++++++++++
 drivers/clk/imx/clk-pfdv2.c                   |  22 +-
 drivers/clk/imx/clk-pllv4.c                   |  34 +-
 drivers/clk/imx/clk.h                         |  24 +-
 include/dt-bindings/clock/imx8ulp-clock.h     | 258 ++++++++
 include/dt-bindings/reset/imx8ulp-pcc-reset.h |  59 ++
 12 files changed, 1142 insertions(+), 32 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml
 create mode 100644 Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml
 create mode 100644 drivers/clk/imx/clk-imx8ulp.c
 create mode 100644 include/dt-bindings/clock/imx8ulp-clock.h
 create mode 100644 include/dt-bindings/reset/imx8ulp-pcc-reset.h
Signature · 1 line
2.26.2
#25 lore raw
In reply to Jacky Bai
Quoted 6 lines · Jacky Bai

This patchset adds the clock & reset driver support for i.MX8ULP. For some of the PCC slot, As there is a SWRST control bit share the same pcc register for peripheral reset ccontrol. To simplify the case, register the pcc reset controller driver when pcc clock driver is registered.

Quoted 7 lines

Patch 1/9 for the dt-bindings part is send out for review previously with the dts patchset:
https://patchwork.kernel.org/project/linux-arm-kernel/cover/[email protected]/

Shawn suggests to send out the clock driver part firstly, so this patch is included in this patchset for now.

Applied all.

Thanks.

Quoted 42 lines

v3 changes:
- split the clock dt schema file into two file, one for pcc, one for cgc

v2 changes:
- remove the useless clocks & clock-names from the dt-binding doc
- remove the redundant fixed clock register.

Anson Huang (1):
clk: imx: disable i.mx7ulp composite clock during initialization

Jacky Bai (8):
dt-bindings: clock: Add imx8ulp clock support
clk: imx: Update the pllv4 to support imx8ulp
clk: imx: Update the compsite driver to support imx8ulp
clk: imx: Add 'CLK_SET_RATE_NO_REPARENT' for composite-7ulp
clk: imx: disable the pfd when set pfdv2 clock rate
clk: imx: Update the pfdv2 for 8ulp specific support
clk: imx: Add clock driver for imx8ulp
clk: imx: Add the pcc reset controller support on imx8ulp

 .../bindings/clock/imx8ulp-cgc-clock.yaml     |  43 ++
 .../bindings/clock/imx8ulp-pcc-clock.yaml     |  50 ++
 drivers/clk/imx/Kconfig                       |   6 +
 drivers/clk/imx/Makefile                      |   2 +
 drivers/clk/imx/clk-composite-7ulp.c          |  87 ++-
 drivers/clk/imx/clk-imx7ulp.c                 |  20 +-
 drivers/clk/imx/clk-imx8ulp.c                 | 569 ++++++++++++++++++
 drivers/clk/imx/clk-pfdv2.c                   |  22 +-
 drivers/clk/imx/clk-pllv4.c                   |  34 +-
 drivers/clk/imx/clk.h                         |  24 +-
 include/dt-bindings/clock/imx8ulp-clock.h     | 258 ++++++++
 include/dt-bindings/reset/imx8ulp-pcc-reset.h |  59 ++
 12 files changed, 1142 insertions(+), 32 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/imx8ulp-cgc-clock.yaml
 create mode 100644 Documentation/devicetree/bindings/clock/imx8ulp-pcc-clock.yaml
 create mode 100644 drivers/clk/imx/clk-imx8ulp.c
 create mode 100644 include/dt-bindings/clock/imx8ulp-clock.h
 create mode 100644 include/dt-bindings/reset/imx8ulp-pcc-reset.h
Signature · 1 line
2.26.2