Performance regression with async inode inactivation
Hello,
our performance testing grid has detected a performance regression caused by commit ab23a77687 ("xfs: per-cpu deferred inode inactivation queues") with reaim benchmark running 'disk' and 'disk-large' workloads. The regression has been so far detected on two machines - marvin7 (48 cpus, 64 GB ram, SATA SSD), dobby (64 cpus, 192 GB ram, rotating disk behind megaraid_sas controller).
The regression reports from mmtests on marvin7 (which from my experience I find more reliable than dobby) look like:
reaim-io-disk-xfs
Hmean disk-1 3597.12 ( 0.00%) 3636.37 ( 1.09%) Hmean disk-25 125000.00 ( 0.00%) 121753.25 ( -2.60%) Hmean disk-49 218424.96 ( 0.00%) 193421.05 * -11.45%* Hmean disk-73 286649.22 ( 0.00%) 240131.58 * -16.23%* Hmean disk-97 349339.74 ( 0.00%) 285854.62 * -18.17%* Hmean disk-121 373456.79 ( 0.00%) 309199.32 * -17.21%* Hmean disk-145 399449.04 ( 0.00%) 330547.11 * -17.25%* Hmean disk-169 420049.71 ( 0.00%) 345132.74 * -17.84%* Hmean disk-193 458795.56 ( 0.00%) 375243.03 * -18.21%* Stddev disk-1 102.32 ( 0.00%) 117.93 ( -15.25%) Stddev disk-25 6981.08 ( 0.00%) 4285.17 ( 38.62%) Stddev disk-49 9523.63 ( 0.00%) 10723.44 ( -12.60%) Stddev disk-73 9704.22 ( 0.00%) 7946.73 ( 18.11%) Stddev disk-97 10059.91 ( 0.00%) 6111.28 ( 39.25%) Stddev disk-121 5730.56 ( 0.00%) 11714.34 (-104.42%) Stddev disk-145 11154.40 ( 0.00%) 8129.06 ( 27.12%) Stddev disk-169 4477.30 ( 0.00%) 3558.86 ( 20.51%) Stddev disk-193 8785.70 ( 0.00%) 13258.89 ( -50.91%)
reaim-io-disk-large-xfs
Hmean disk-1 722.72 ( 0.00%) 721.85 ( -0.12%) Hmean disk-25 24177.95 ( 0.00%) 24319.06 ( 0.58%) Hmean disk-49 35294.12 ( 0.00%) 34361.85 ( -2.64%) Hmean disk-73 43042.45 ( 0.00%) 40896.36 * -4.99%* Hmean disk-97 48403.19 ( 0.00%) 46044.30 * -4.87%* Hmean disk-121 52230.22 ( 0.00%) 49347.47 * -5.52%* Hmean disk-145 54613.94 ( 0.00%) 52333.98 * -4.17%* Hmean disk-169 57178.30 ( 0.00%) 54745.71 * -4.25%* Hmean disk-193 60230.94 ( 0.00%) 57106.22 * -5.19%* Stddev disk-1 18.74 ( 0.00%) 30.19 ( -61.11%) Stddev disk-25 439.49 ( 0.00%) 809.58 ( -84.21%) Stddev disk-49 1416.65 ( 0.00%) 603.55 ( 57.40%) Stddev disk-73 949.45 ( 0.00%) 584.61 ( 38.43%) Stddev disk-97 689.51 ( 0.00%) 602.76 ( 12.58%) Stddev disk-121 485.22 ( 0.00%) 612.79 ( -26.29%) Stddev disk-145 147.37 ( 0.00%) 442.99 (-200.60%) Stddev disk-169 282.25 ( 0.00%) 613.42 (-117.33%) Stddev disk-193 970.05 ( 0.00%) 572.59 ( 40.97%)
Note that numbers behind dash (disk-xx) denote the number of reaim "clients" - i.e., the number of processes reaim runs in parallel.
This reaim workload will create quite some small files, fsync them, do a few operations on them like read, write, etc. and quickly delete them. This happens in many processes in parallel so I can imagine the unlink workload is rather heavy.
To reproduce the workload the easiest is probably to clone mmtests [1], there's README.md and docs/Tutorial.md about how to run tests. Relevant configurations are in configs/config-reaim-io-disk-large and configs/config-reaim-io-disk, you will need to edit these files to set appropriate test partition (will get wiped) and filesystem. Note that mmtests do somewhat modify standard reaim benchmark so that it does not call system("sync") after each operation (you can see modifications we apply in [2] if you're interested).
I can probably find some time to better understand what's going on on these machines later this week but if you have some suggestions what to look for, you're welcome.
Honza
[1] https://github.com/gormanm/mmtests
[2] https://github.com/gormanm/mmtests/blob/master/shellpack_src/src/reaim/reaim-install
Signature · 2 lines
Jan Kara <[email protected]> SUSE Labs, CR
Quoted 8 lines · Jan Kara
Hello,
our performance testing grid has detected a performance regression caused by commit
ab23a77687("xfs: per-cpu deferred inode inactivation queues") with reaim benchmark running 'disk' and 'disk-large' workloads. The regression has been so far detected on two machines - marvin7 (48 cpus, 64 GB ram, SATA SSD), dobby (64 cpus, 192 GB ram, rotating disk behindmegaraid_sascontroller).
I'll think about this some more, but for now my immediate reaction is to point out the previous discussion about aim7 reporting a similar (percentage point) regression:
https://lore.kernel.org/lkml/20210909142355.GA6270@xsang-OptiPlex-9020/
--D
Quoted 73 lines
The regression reports from mmtests on marvin7 (which from my experience I find more reliable than dobby) look like:
reaim-io-disk-xfs
Hmean disk-1 3597.12 ( 0.00%) 3636.37 ( 1.09%) Hmean disk-25 125000.00 ( 0.00%) 121753.25 ( -2.60%) Hmean disk-49 218424.96 ( 0.00%) 193421.05 * -11.45%* Hmean disk-73 286649.22 ( 0.00%) 240131.58 * -16.23%* Hmean disk-97 349339.74 ( 0.00%) 285854.62 * -18.17%* Hmean disk-121 373456.79 ( 0.00%) 309199.32 * -17.21%* Hmean disk-145 399449.04 ( 0.00%) 330547.11 * -17.25%* Hmean disk-169 420049.71 ( 0.00%) 345132.74 * -17.84%* Hmean disk-193 458795.56 ( 0.00%) 375243.03 * -18.21%* Stddev disk-1 102.32 ( 0.00%) 117.93 ( -15.25%) Stddev disk-25 6981.08 ( 0.00%) 4285.17 ( 38.62%) Stddev disk-49 9523.63 ( 0.00%) 10723.44 ( -12.60%) Stddev disk-73 9704.22 ( 0.00%) 7946.73 ( 18.11%) Stddev disk-97 10059.91 ( 0.00%) 6111.28 ( 39.25%) Stddev disk-121 5730.56 ( 0.00%) 11714.34 (-104.42%) Stddev disk-145 11154.40 ( 0.00%) 8129.06 ( 27.12%) Stddev disk-169 4477.30 ( 0.00%) 3558.86 ( 20.51%) Stddev disk-193 8785.70 ( 0.00%) 13258.89 ( -50.91%)reaim-io-disk-large-xfs
Hmean disk-1 722.72 ( 0.00%) 721.85 ( -0.12%) Hmean disk-25 24177.95 ( 0.00%) 24319.06 ( 0.58%) Hmean disk-49 35294.12 ( 0.00%) 34361.85 ( -2.64%) Hmean disk-73 43042.45 ( 0.00%) 40896.36 * -4.99%* Hmean disk-97 48403.19 ( 0.00%) 46044.30 * -4.87%* Hmean disk-121 52230.22 ( 0.00%) 49347.47 * -5.52%* Hmean disk-145 54613.94 ( 0.00%) 52333.98 * -4.17%* Hmean disk-169 57178.30 ( 0.00%) 54745.71 * -4.25%* Hmean disk-193 60230.94 ( 0.00%) 57106.22 * -5.19%* Stddev disk-1 18.74 ( 0.00%) 30.19 ( -61.11%) Stddev disk-25 439.49 ( 0.00%) 809.58 ( -84.21%) Stddev disk-49 1416.65 ( 0.00%) 603.55 ( 57.40%) Stddev disk-73 949.45 ( 0.00%) 584.61 ( 38.43%) Stddev disk-97 689.51 ( 0.00%) 602.76 ( 12.58%) Stddev disk-121 485.22 ( 0.00%) 612.79 ( -26.29%) Stddev disk-145 147.37 ( 0.00%) 442.99 (-200.60%) Stddev disk-169 282.25 ( 0.00%) 613.42 (-117.33%) Stddev disk-193 970.05 ( 0.00%) 572.59 ( 40.97%)Note that numbers behind dash (disk-xx) denote the number of reaim "clients" - i.e., the number of processes reaim runs in parallel.
This reaim workload will create quite some small files, fsync them, do a few operations on them like read, write, etc. and quickly delete them. This happens in many processes in parallel so I can imagine the unlink workload is rather heavy.
To reproduce the workload the easiest is probably to clone mmtests [1], there's README.md and
docs/Tutorial.mdabout how to run tests. Relevant configurations are in configs/config-reaim-io-disk-large and configs/config-reaim-io-disk, you will need to edit these files to set appropriate test partition (will get wiped) and filesystem. Note that mmtests do somewhat modify standard reaim benchmark so that it does not callsystem("sync")after each operation (you can see modifications we apply in [2] if you're interested).I can probably find some time to better understand what's going on on these machines later this week but if you have some suggestions what to look for, you're welcome.
Honza
[1] https://github.com/gormanm/mmtests
[2] https://github.com/gormanm/mmtests/blob/master/shellpack_src/src/reaim/reaim-installSignature · 2 lines
Jan Kara <[email protected]> SUSE Labs, CR
Quoted 8 lines · Jan Kara
Hello,
our performance testing grid has detected a performance regression caused by commit
ab23a77687("xfs: per-cpu deferred inode inactivation queues") with reaim benchmark running 'disk' and 'disk-large' workloads. The regression has been so far detected on two machines - marvin7 (48 cpus, 64 GB ram, SATA SSD), dobby (64 cpus, 192 GB ram, rotating disk behindmegaraid_sascontroller).
Yup, large cpu count, single slow disk, and the cause will likely be exclusive rwsem lock contention on a directory inode that concurrent openat and unlink are occuring in.
Basically, that commit removed a bunch of userspace overhead in unlinks, when mean they run as fast as the unlink() call can remove the directory entry. There is effectively nothing throttling unlink() in XFS now except for available log space and it mostly runs to completion without blocking. Hence the front end unlink performance can run in much faster bursts before delayed inactivation needs to run.
Given most of the added CPU overhead is in the rwsem spin_on_owner path, it implies that the write lock holder is, indeed, not sleeping with the lock held. Hence reaim is hitting a borderline contended rwsem much harder and with different behaviour, resulting in catastrophic breakdown of lock performance and hence unlink performance goes backwards.
I can't see any other new sleeping lock contention in the workload profiles - the context switch rate goes down substantially (by 35%!) with commit ab23a77687, which also implies that the lock contention is resulting in much longer spin and/or sleep times on the lock.
I'm not sure we can do anything about this in the filesystem. The contended lock is a core, high level VFS lock which is the first point of unlinkat() syscall serialisation. This is the lock that is directly exposed to userspace concurrency, so the scalability of this lock determines concurrency performance of the userspace application.....
Quoted 43 lines
The regression reports from mmtests on marvin7 (which from my experience I find more reliable than dobby) look like:
reaim-io-disk-xfs
Hmean disk-1 3597.12 ( 0.00%) 3636.37 ( 1.09%) Hmean disk-25 125000.00 ( 0.00%) 121753.25 ( -2.60%) Hmean disk-49 218424.96 ( 0.00%) 193421.05 * -11.45%* Hmean disk-73 286649.22 ( 0.00%) 240131.58 * -16.23%* Hmean disk-97 349339.74 ( 0.00%) 285854.62 * -18.17%* Hmean disk-121 373456.79 ( 0.00%) 309199.32 * -17.21%* Hmean disk-145 399449.04 ( 0.00%) 330547.11 * -17.25%* Hmean disk-169 420049.71 ( 0.00%) 345132.74 * -17.84%* Hmean disk-193 458795.56 ( 0.00%) 375243.03 * -18.21%* Stddev disk-1 102.32 ( 0.00%) 117.93 ( -15.25%) Stddev disk-25 6981.08 ( 0.00%) 4285.17 ( 38.62%) Stddev disk-49 9523.63 ( 0.00%) 10723.44 ( -12.60%) Stddev disk-73 9704.22 ( 0.00%) 7946.73 ( 18.11%) Stddev disk-97 10059.91 ( 0.00%) 6111.28 ( 39.25%) Stddev disk-121 5730.56 ( 0.00%) 11714.34 (-104.42%) Stddev disk-145 11154.40 ( 0.00%) 8129.06 ( 27.12%) Stddev disk-169 4477.30 ( 0.00%) 3558.86 ( 20.51%) Stddev disk-193 8785.70 ( 0.00%) 13258.89 ( -50.91%)reaim-io-disk-large-xfs
Hmean disk-1 722.72 ( 0.00%) 721.85 ( -0.12%) Hmean disk-25 24177.95 ( 0.00%) 24319.06 ( 0.58%) Hmean disk-49 35294.12 ( 0.00%) 34361.85 ( -2.64%) Hmean disk-73 43042.45 ( 0.00%) 40896.36 * -4.99%* Hmean disk-97 48403.19 ( 0.00%) 46044.30 * -4.87%* Hmean disk-121 52230.22 ( 0.00%) 49347.47 * -5.52%* Hmean disk-145 54613.94 ( 0.00%) 52333.98 * -4.17%* Hmean disk-169 57178.30 ( 0.00%) 54745.71 * -4.25%* Hmean disk-193 60230.94 ( 0.00%) 57106.22 * -5.19%* Stddev disk-1 18.74 ( 0.00%) 30.19 ( -61.11%) Stddev disk-25 439.49 ( 0.00%) 809.58 ( -84.21%) Stddev disk-49 1416.65 ( 0.00%) 603.55 ( 57.40%) Stddev disk-73 949.45 ( 0.00%) 584.61 ( 38.43%) Stddev disk-97 689.51 ( 0.00%) 602.76 ( 12.58%) Stddev disk-121 485.22 ( 0.00%) 612.79 ( -26.29%) Stddev disk-145 147.37 ( 0.00%) 442.99 (-200.60%) Stddev disk-169 282.25 ( 0.00%) 613.42 (-117.33%) Stddev disk-193 970.05 ( 0.00%) 572.59 ( 40.97%)
Quoted 7 lines
Note that numbers behind dash (disk-xx) denote the number of reaim "clients" - i.e., the number of processes reaim runs in parallel.
This reaim workload will create quite some small files, fsync them, do a few operations on them like read, write, etc. and quickly delete them. This happens in many processes in parallel so I can imagine the unlink workload is rather heavy.
Yup, which is why I've largely been ignoring it. reaim is a *very old* benchmark that doesn't do anything we'd normally do to scale out independent workloads effectively.
Quoted 9 lines
To reproduce the workload the easiest is probably to clone mmtests [1], there's README.md and
docs/Tutorial.mdabout how to run tests. Relevant configurations are in configs/config-reaim-io-disk-large and configs/config-reaim-io-disk, you will need to edit these files to set appropriate test partition (will get wiped) and filesystem. Note that mmtests do somewhat modify standard reaim benchmark so that it does not callsystem("sync")after each operation (you can see modifications we apply in [2] if you're interested).
Quoted 3 lines
I can probably find some time to better understand what's going on on these machines later this week but if you have some suggestions what to look for, you're welcome.
You should be able to reproduce the concurrent unlink contention simply by running a bunch of concurrent unlinks in a directory and watching the directory i_rwsem get absolutely hammered up in do_unlinkat().
Cheers,
Dave.
Signature · 2 lines
Dave Chinner [email protected]
Quoted 34 lines · Dave Chinner
Quoted 8 lines · Jan Kara
Hello,
our performance testing grid has detected a performance regression caused by commit
ab23a77687("xfs: per-cpu deferred inode inactivation queues") with reaim benchmark running 'disk' and 'disk-large' workloads. The regression has been so far detected on two machines - marvin7 (48 cpus, 64 GB ram, SATA SSD), dobby (64 cpus, 192 GB ram, rotating disk behindmegaraid_sascontroller).Yup, large cpu count, single slow disk, and the cause will likely be exclusive rwsem lock contention on a directory inode that concurrent openat and unlink are occuring in.
Basically, that commit removed a bunch of userspace overhead in unlinks, when mean they run as fast as the
unlink()call can remove the directory entry. There is effectively nothing throttlingunlink()in XFS now except for available log space and it mostly runs to completion without blocking. Hence the front end unlink performance can run in much faster bursts before delayed inactivation needs to run.Given most of the added CPU overhead is in the rwsem
spin_on_ownerpath, it implies that the write lock holder is, indeed, not sleeping with the lock held. Hence reaim is hitting a borderline contended rwsem much harder and with different behaviour, resulting in catastrophic breakdown of lock performance and hence unlink performance goes backwards.I can't see any other new sleeping lock contention in the workload profiles - the context switch rate goes down substantially (by 35%!) with commit
ab23a77687, which also implies that the lock contention is resulting in much longer spin and/or sleep times on the lock.
Quoted 6 lines
I'm not sure we can do anything about this in the filesystem. The contended lock is a core, high level VFS lock which is the first point of
unlinkat()syscall serialisation. This is the lock that is directly exposed to userspace concurrency, so the scalability of this lock determines concurrency performance of the userspace application.....
Thanks for explanation! It makes sense, except one difference I can see in vmstat on both marvin7 and dobby which I don't understand:
Dobby:
Ops Sector Reads 1009081.00 1009081.00
Ops Sector Writes 11550795.00 18753764.00
Marvin7:
Ops Sector Reads 887951.00 887951.00
Ops Sector Writes 8248822.00 11135086.00
So after the change reaim ends up doing noticeably more writes. I had a look at iostat comparison as well but there wasn't anything particular standing out besides higher amount of writes on the test disk. I guess, I'll limit the number of clients to a single number showing the regression, enable some more detailed monitoring and see whether something interesting pops up.
Quoted 46 lines
Quoted 46 lines
The regression reports from mmtests on marvin7 (which from my experience I find more reliable than dobby) look like:
reaim-io-disk-xfs
Hmean disk-1 3597.12 ( 0.00%) 3636.37 ( 1.09%) Hmean disk-25 125000.00 ( 0.00%) 121753.25 ( -2.60%) Hmean disk-49 218424.96 ( 0.00%) 193421.05 * -11.45%* Hmean disk-73 286649.22 ( 0.00%) 240131.58 * -16.23%* Hmean disk-97 349339.74 ( 0.00%) 285854.62 * -18.17%* Hmean disk-121 373456.79 ( 0.00%) 309199.32 * -17.21%* Hmean disk-145 399449.04 ( 0.00%) 330547.11 * -17.25%* Hmean disk-169 420049.71 ( 0.00%) 345132.74 * -17.84%* Hmean disk-193 458795.56 ( 0.00%) 375243.03 * -18.21%* Stddev disk-1 102.32 ( 0.00%) 117.93 ( -15.25%) Stddev disk-25 6981.08 ( 0.00%) 4285.17 ( 38.62%) Stddev disk-49 9523.63 ( 0.00%) 10723.44 ( -12.60%) Stddev disk-73 9704.22 ( 0.00%) 7946.73 ( 18.11%) Stddev disk-97 10059.91 ( 0.00%) 6111.28 ( 39.25%) Stddev disk-121 5730.56 ( 0.00%) 11714.34 (-104.42%) Stddev disk-145 11154.40 ( 0.00%) 8129.06 ( 27.12%) Stddev disk-169 4477.30 ( 0.00%) 3558.86 ( 20.51%) Stddev disk-193 8785.70 ( 0.00%) 13258.89 ( -50.91%)reaim-io-disk-large-xfs
Hmean disk-1 722.72 ( 0.00%) 721.85 ( -0.12%) Hmean disk-25 24177.95 ( 0.00%) 24319.06 ( 0.58%) Hmean disk-49 35294.12 ( 0.00%) 34361.85 ( -2.64%) Hmean disk-73 43042.45 ( 0.00%) 40896.36 * -4.99%* Hmean disk-97 48403.19 ( 0.00%) 46044.30 * -4.87%* Hmean disk-121 52230.22 ( 0.00%) 49347.47 * -5.52%* Hmean disk-145 54613.94 ( 0.00%) 52333.98 * -4.17%* Hmean disk-169 57178.30 ( 0.00%) 54745.71 * -4.25%* Hmean disk-193 60230.94 ( 0.00%) 57106.22 * -5.19%* Stddev disk-1 18.74 ( 0.00%) 30.19 ( -61.11%) Stddev disk-25 439.49 ( 0.00%) 809.58 ( -84.21%) Stddev disk-49 1416.65 ( 0.00%) 603.55 ( 57.40%) Stddev disk-73 949.45 ( 0.00%) 584.61 ( 38.43%) Stddev disk-97 689.51 ( 0.00%) 602.76 ( 12.58%) Stddev disk-121 485.22 ( 0.00%) 612.79 ( -26.29%) Stddev disk-145 147.37 ( 0.00%) 442.99 (-200.60%) Stddev disk-169 282.25 ( 0.00%) 613.42 (-117.33%) Stddev disk-193 970.05 ( 0.00%) 572.59 ( 40.97%)Note that numbers behind dash (disk-xx) denote the number of reaim "clients" - i.e., the number of processes reaim runs in parallel.
Quoted 8 lines
Quoted 4 lines
This reaim workload will create quite some small files, fsync them, do a few operations on them like read, write, etc. and quickly delete them. This happens in many processes in parallel so I can imagine the unlink workload is rather heavy.
Yup, which is why I've largely been ignoring it. reaim is a *very old* benchmark that doesn't do anything we'd normally do to scale out independent workloads effectively.
Yes, I agree reaim is a stupid workload for today's standards so I'm not much worried about it as such. Just occasionally it tends to highlight problems that are valid also for more relevant workloads (just less visible there) so we still run it.
Quoted 9 lines
Quoted 9 lines
To reproduce the workload the easiest is probably to clone mmtests [1], there's README.md and
docs/Tutorial.mdabout how to run tests. Relevant configurations are in configs/config-reaim-io-disk-large and configs/config-reaim-io-disk, you will need to edit these files to set appropriate test partition (will get wiped) and filesystem. Note that mmtests do somewhat modify standard reaim benchmark so that it does not callsystem("sync")after each operation (you can see modifications we apply in [2] if you're interested).
Quoted 8 lines
Quoted 3 lines
I can probably find some time to better understand what's going on on these machines later this week but if you have some suggestions what to look for, you're welcome.
You should be able to reproduce the concurrent unlink contention simply by running a bunch of concurrent unlinks in a directory and watching the directory
i_rwsemget absolutely hammered up indo_unlinkat().
OK, thanks for suggestion. I can try that as well.
Honza
Signature · 2 lines
Jan Kara <[email protected]> SUSE Labs, CR
Quoted 53 lines · Jan Kara
Quoted 34 lines · Dave Chinner
Quoted 8 lines · Jan Kara
Hello,
our performance testing grid has detected a performance regression caused by commit
ab23a77687("xfs: per-cpu deferred inode inactivation queues") with reaim benchmark running 'disk' and 'disk-large' workloads. The regression has been so far detected on two machines - marvin7 (48 cpus, 64 GB ram, SATA SSD), dobby (64 cpus, 192 GB ram, rotating disk behindmegaraid_sascontroller).Yup, large cpu count, single slow disk, and the cause will likely be exclusive rwsem lock contention on a directory inode that concurrent openat and unlink are occuring in.
Basically, that commit removed a bunch of userspace overhead in unlinks, when mean they run as fast as the
unlink()call can remove the directory entry. There is effectively nothing throttlingunlink()in XFS now except for available log space and it mostly runs to completion without blocking. Hence the front end unlink performance can run in much faster bursts before delayed inactivation needs to run.Given most of the added CPU overhead is in the rwsem
spin_on_ownerpath, it implies that the write lock holder is, indeed, not sleeping with the lock held. Hence reaim is hitting a borderline contended rwsem much harder and with different behaviour, resulting in catastrophic breakdown of lock performance and hence unlink performance goes backwards.I can't see any other new sleeping lock contention in the workload profiles - the context switch rate goes down substantially (by 35%!) with commit
ab23a77687, which also implies that the lock contention is resulting in much longer spin and/or sleep times on the lock.Quoted 6 lines
I'm not sure we can do anything about this in the filesystem. The contended lock is a core, high level VFS lock which is the first point of
unlinkat()syscall serialisation. This is the lock that is directly exposed to userspace concurrency, so the scalability of this lock determines concurrency performance of the userspace application.....Thanks for explanation! It makes sense, except one difference I can see in vmstat on both marvin7 and dobby which I don't understand:
Dobby:
Ops Sector Reads 1009081.00 1009081.00
Ops Sector Writes 11550795.00 18753764.00Marvin7:
Ops Sector Reads 887951.00 887951.00
Ops Sector Writes 8248822.00 11135086.00
Quoted 6 lines
So after the change reaim ends up doing noticeably more writes. I had a look at iostat comparison as well but there wasn't anything particular standing out besides higher amount of writes on the test disk. I guess, I'll limit the number of clients to a single number showing the regression, enable some more detailed monitoring and see whether something interesting pops up.
Interesting.
There weren't iostats in the original intel profiles given. I can see a couple of vmstats that give some indications - vmstat.io.bo went up from ~2500 to ~6000, and proc-vmstat.pgpgout went up from ~90k to 250k.
Looking at another more recent profile, there are more IO related stats in the output vmstat.nr_written went up by 2.5x and vmstat.pgpgout went up by a factor of 6 (50k -> 300k) but otherwise everything else was fairly constant in the VM. The resident size of the file cache is small, and vmstat.nr_dirtied went up by a small ammount by it's 4 orders of magnitude larger than nr_written.
Hmmm. That implies a *lot* of overwrite of cached files.
I wonder if we've just changed the memory pressure enough to trigger more frequent writeback? We're delaying the inactivation (and hence page cache invalidation) of up to 256 inodes per CPU, and the number of cached+dirty inodes appears to have increased a small amount (from ~3000 to ~4000). With slow disks, a small change in writeback behaviour could cause seek-bound related performance regressions.
Also worth noting is that there's been some recent variance in reaim numbers recently because of the journal FUA/flush optimisations we've made. Some machines report +20% from that change, some report -20%, and there's no pattern to it. It's just another indication that the reaim scalability and perf on these large CPU count, single spinning disk setups is highly dependent on disk performance and seek optimisation...
Have you run any tests on a system that isn't stupidly overpowered for it's disk subsystem? e.g. has an SSD rather than spinning rust?
Quoted 51 lines
Quoted 51 lines
Quoted 50 lines
The regression reports from mmtests on marvin7 (which from my experience I find more reliable than dobby) look like:
reaim-io-disk-xfs
Hmean disk-1 3597.12 ( 0.00%) 3636.37 ( 1.09%) Hmean disk-25 125000.00 ( 0.00%) 121753.25 ( -2.60%) Hmean disk-49 218424.96 ( 0.00%) 193421.05 * -11.45%* Hmean disk-73 286649.22 ( 0.00%) 240131.58 * -16.23%* Hmean disk-97 349339.74 ( 0.00%) 285854.62 * -18.17%* Hmean disk-121 373456.79 ( 0.00%) 309199.32 * -17.21%* Hmean disk-145 399449.04 ( 0.00%) 330547.11 * -17.25%* Hmean disk-169 420049.71 ( 0.00%) 345132.74 * -17.84%* Hmean disk-193 458795.56 ( 0.00%) 375243.03 * -18.21%* Stddev disk-1 102.32 ( 0.00%) 117.93 ( -15.25%) Stddev disk-25 6981.08 ( 0.00%) 4285.17 ( 38.62%) Stddev disk-49 9523.63 ( 0.00%) 10723.44 ( -12.60%) Stddev disk-73 9704.22 ( 0.00%) 7946.73 ( 18.11%) Stddev disk-97 10059.91 ( 0.00%) 6111.28 ( 39.25%) Stddev disk-121 5730.56 ( 0.00%) 11714.34 (-104.42%) Stddev disk-145 11154.40 ( 0.00%) 8129.06 ( 27.12%) Stddev disk-169 4477.30 ( 0.00%) 3558.86 ( 20.51%) Stddev disk-193 8785.70 ( 0.00%) 13258.89 ( -50.91%)reaim-io-disk-large-xfs
Hmean disk-1 722.72 ( 0.00%) 721.85 ( -0.12%) Hmean disk-25 24177.95 ( 0.00%) 24319.06 ( 0.58%) Hmean disk-49 35294.12 ( 0.00%) 34361.85 ( -2.64%) Hmean disk-73 43042.45 ( 0.00%) 40896.36 * -4.99%* Hmean disk-97 48403.19 ( 0.00%) 46044.30 * -4.87%* Hmean disk-121 52230.22 ( 0.00%) 49347.47 * -5.52%* Hmean disk-145 54613.94 ( 0.00%) 52333.98 * -4.17%* Hmean disk-169 57178.30 ( 0.00%) 54745.71 * -4.25%* Hmean disk-193 60230.94 ( 0.00%) 57106.22 * -5.19%* Stddev disk-1 18.74 ( 0.00%) 30.19 ( -61.11%) Stddev disk-25 439.49 ( 0.00%) 809.58 ( -84.21%) Stddev disk-49 1416.65 ( 0.00%) 603.55 ( 57.40%) Stddev disk-73 949.45 ( 0.00%) 584.61 ( 38.43%) Stddev disk-97 689.51 ( 0.00%) 602.76 ( 12.58%) Stddev disk-121 485.22 ( 0.00%) 612.79 ( -26.29%) Stddev disk-145 147.37 ( 0.00%) 442.99 (-200.60%) Stddev disk-169 282.25 ( 0.00%) 613.42 (-117.33%) Stddev disk-193 970.05 ( 0.00%) 572.59 ( 40.97%)Note that numbers behind dash (disk-xx) denote the number of reaim "clients" - i.e., the number of processes reaim runs in parallel.
This reaim workload will create quite some small files, fsync them, do a few operations on them like read, write, etc. and quickly delete them. This happens in many processes in parallel so I can imagine the unlink workload is rather heavy.
Quoted 8 lines
Quoted 3 lines
Yup, which is why I've largely been ignoring it. reaim is a *very old* benchmark that doesn't do anything we'd normally do to scale out independent workloads effectively.
Yes, I agree reaim is a stupid workload for today's standards so I'm not much worried about it as such. Just occasionally it tends to highlight problems that are valid also for more relevant workloads (just less visible there) so we still run it.
*nod*
It has worked well as a canary in past times, but recently I'm finding we're getting more noise than useful signal from these unbalanced "all CPU, no IO" test machine configs these days....
Cheers,
Dave.
Signature · 2 lines
Dave Chinner [email protected]
Quoted 92 lines · Dave Chinner
Quoted 53 lines · Jan Kara
Quoted 34 lines · Dave Chinner
Quoted 8 lines · Jan Kara
Hello,
our performance testing grid has detected a performance regression caused by commit
ab23a77687("xfs: per-cpu deferred inode inactivation queues") with reaim benchmark running 'disk' and 'disk-large' workloads. The regression has been so far detected on two machines - marvin7 (48 cpus, 64 GB ram, SATA SSD), dobby (64 cpus, 192 GB ram, rotating disk behindmegaraid_sascontroller).Yup, large cpu count, single slow disk, and the cause will likely be exclusive rwsem lock contention on a directory inode that concurrent openat and unlink are occuring in.
Basically, that commit removed a bunch of userspace overhead in unlinks, when mean they run as fast as the
unlink()call can remove the directory entry. There is effectively nothing throttlingunlink()in XFS now except for available log space and it mostly runs to completion without blocking. Hence the front end unlink performance can run in much faster bursts before delayed inactivation needs to run.Given most of the added CPU overhead is in the rwsem
spin_on_ownerpath, it implies that the write lock holder is, indeed, not sleeping with the lock held. Hence reaim is hitting a borderline contended rwsem much harder and with different behaviour, resulting in catastrophic breakdown of lock performance and hence unlink performance goes backwards.I can't see any other new sleeping lock contention in the workload profiles - the context switch rate goes down substantially (by 35%!) with commit
ab23a77687, which also implies that the lock contention is resulting in much longer spin and/or sleep times on the lock.Quoted 6 lines
I'm not sure we can do anything about this in the filesystem. The contended lock is a core, high level VFS lock which is the first point of
unlinkat()syscall serialisation. This is the lock that is directly exposed to userspace concurrency, so the scalability of this lock determines concurrency performance of the userspace application.....Thanks for explanation! It makes sense, except one difference I can see in vmstat on both marvin7 and dobby which I don't understand:
Dobby:
Ops Sector Reads 1009081.00 1009081.00
Ops Sector Writes 11550795.00 18753764.00Marvin7:
Ops Sector Reads 887951.00 887951.00
Ops Sector Writes 8248822.00 11135086.00Quoted 6 lines
So after the change reaim ends up doing noticeably more writes. I had a look at iostat comparison as well but there wasn't anything particular standing out besides higher amount of writes on the test disk. I guess, I'll limit the number of clients to a single number showing the regression, enable some more detailed monitoring and see whether something interesting pops up.
Interesting.
There weren't iostats in the original intel profiles given. I can see a couple of vmstats that give some indications - vmstat.io.bo went up from ~2500 to ~6000, and proc-vmstat.pgpgout went up from ~90k to 250k.
Looking at another more recent profile, there are more IO related stats in the output vmstat.nr_written went up by 2.5x and vmstat.pgpgout went up by a factor of 6 (50k -> 300k) but otherwise everything else was fairly constant in the VM. The resident size of the file cache is small, and vmstat.nr_dirtied went up by a small ammount by it's 4 orders of magnitude larger than
nr_written.Hmmm. That implies a *lot* of overwrite of cached files.
I wonder if we've just changed the memory pressure enough to trigger more frequent writeback? We're delaying the inactivation (and hence page cache invalidation) of up to 256 inodes per CPU, and the number of cached+dirty inodes appears to have increased a small amount (from ~3000 to ~4000). With slow disks, a small change in writeback behaviour could cause seek-bound related performance regressions.
Also worth noting is that there's been some recent variance in reaim numbers recently because of the journal FUA/flush optimisations we've made. Some machines report +20% from that change, some report -20%, and there's no pattern to it. It's just another indication that the reaim scalability and perf on these large CPU count, single spinning disk setups is highly dependent on disk performance and seek optimisation...
Quoted 2 lines
Have you run any tests on a system that isn't stupidly overpowered for it's disk subsystem? e.g. has an SSD rather than spinning rust?
So marvin7 actually has SSD. I was experimenting some more. Attached is a simple reproducer that demonstrates the issue for me - it just creates 16k file, fsync it, delete it in a loop from given number processes (I run with 48). The reproducer runs ~25% slower after the commit ab23a77687. Note that the reproducer makes each process use a different directory so i_rwsem contention is out of question.
From blktrace I can see that indeed after the commit we do ~25% more writes. Each stress-unlink process does the same amount of IO, the extra IO comes solely from the worker threads. Also I'd note that before the commit we were reusing blocks much more (likely inode blocks getting reused) - before the commit we write to ~88 MB worth of distinct disk blocks, after the commit we write to ~296 MB worth of distinct disk blocks. That's understandable given the delayed inode freeing but it's one thing that could possibly have effect. That's how far I've come today, I'll dig more tomorrow.
Honza
Signature · 2 lines
Jan Kara <[email protected]> SUSE Labs, CR
#include <stdio.h>
#include <fcntl.h>
#include <stdlib.h>
#include <errno.h>
#include <string.h>
#include <signal.h>
#include <unistd.h>
#include <sys/wait.h>
#include <sys/mman.h>
#include <sys/stat.h>
#include <sys/time.h>
#define COUNT 100
#define SIZE 16384
#define MAX_PROCS 1024
char shm_name[64];
char wbuf[SIZE];
void prepare(char *base, int num)
{
char dir[128];
sprintf(dir, "%s/dir-%d", base, num);
if (mkdir(dir, 0700) < 0 && errno != EEXIST) {
perror("mkdir");
exit(1);
}
}void teardown(char *base, int num)
{
char dir[128];
sprintf(dir, "%s/dir-%d", base, num);
rmdir(dir);
}void run_test(char *base, int num)
{
char name[128];
int shmfd;
int i;
int *shm;
int fd;
sprintf(name, "%s/dir-%d/file", base, num);
shmfd = shm_open(shm_name, O_RDWR, 0);
if (shmfd < 0) {
perror("shm_open");
exit(1);
}
shm = mmap(NULL, sizeof(int) * MAX_PROCS, PROT_READ | PROT_WRITE,
MAP_SHARED, shmfd, 0);
if (shm == MAP_FAILED) {
perror("mmap");
exit(1);
}
shm[num + 1] = 1;
while (shm[0] == 0)
usleep(1);
for (i = 0; i < COUNT; i++) {
fd = open(name, O_CREAT | O_WRONLY, 0644);
if (fd < 0) {
perror("open");
exit(1);
}
if (write(fd, wbuf, SIZE) != SIZE) {
perror("pwrite");
exit(1);
}
fsync(fd);
close(fd);
unlink(name);
}
}int main(int argc, char **argv)
{
int procs, i, j;
pid_t pids[MAX_PROCS];
int shmfd;
int *shm;
struct timeval start, end;
long long ms;
if (argc != 3) {
fprintf(stderr, "Usage: stress-unlink <processes> <dir>\n");
return 1;
}
procs = strtol(argv[1], NULL, 10);
if (procs > MAX_PROCS) {
fprintf(stderr, "Too many processes!\n");
return 1;
}
memset(wbuf, 0xcc, SIZE);
sprintf(shm_name, "/stress-unlink-%u", getpid());
shmfd = shm_open(shm_name, O_CREAT | O_RDWR, 0600);
if (shmfd < 0) {
perror("shm_open");
return 1;
}
if (ftruncate(shmfd, sizeof(int) * MAX_PROCS) < 0) {
perror("ftruncate shm");
return 1;
}
shm = mmap(NULL, sizeof(int) * MAX_PROCS, PROT_READ | PROT_WRITE,
MAP_SHARED, shmfd, 0);
if (shm == MAP_FAILED) {
perror("mmap");
return 1;
}
shm[0] = 0;
for (i = 0; i < procs; i++) {
shm[i+1] = 0;
prepare(argv[2], i);
}
for (i = 0; i < procs; i++) {
pids[i] = fork();
if (pids[i] < 0) {
perror("fork");
for (j = 0; j < i; j++)
kill(pids[j], SIGKILL);
return 1;
}
if (pids[i] == 0) {
run_test(argv[2], i);
exit(0);
}
}
do {
for (i = 0; i < procs && shm[i + 1]; i++);
} while (i != procs);
gettimeofday(&start, NULL);
shm[0] = 1;
fprintf(stderr, "Processes started.\n");
for (i = 0; i < procs; i++)
waitpid(pids[i], NULL, 0);
gettimeofday(&end, NULL);
for (i = 0; i < procs; i++)
teardown(argv[2], i);
shm_unlink(shm_name);
ms = (((long long)(end.tv_sec - start.tv_sec) * 1000000) +
(end.tv_usec - start.tv_usec)) / 1000;
printf("%lld.%03lld\n", ms/1000, ms%1000);
return 0;
}Quoted 103 lines · Jan Kara
Quoted 92 lines · Dave Chinner
Quoted 53 lines · Jan Kara
Quoted 34 lines · Dave Chinner
Quoted 8 lines · Jan Kara
Hello,
our performance testing grid has detected a performance regression caused by commit
ab23a77687("xfs: per-cpu deferred inode inactivation queues") with reaim benchmark running 'disk' and 'disk-large' workloads. The regression has been so far detected on two machines - marvin7 (48 cpus, 64 GB ram, SATA SSD), dobby (64 cpus, 192 GB ram, rotating disk behindmegaraid_sascontroller).Yup, large cpu count, single slow disk, and the cause will likely be exclusive rwsem lock contention on a directory inode that concurrent openat and unlink are occuring in.
Basically, that commit removed a bunch of userspace overhead in unlinks, when mean they run as fast as the
unlink()call can remove the directory entry. There is effectively nothing throttlingunlink()in XFS now except for available log space and it mostly runs to completion without blocking. Hence the front end unlink performance can run in much faster bursts before delayed inactivation needs to run.Given most of the added CPU overhead is in the rwsem
spin_on_ownerpath, it implies that the write lock holder is, indeed, not sleeping with the lock held. Hence reaim is hitting a borderline contended rwsem much harder and with different behaviour, resulting in catastrophic breakdown of lock performance and hence unlink performance goes backwards.I can't see any other new sleeping lock contention in the workload profiles - the context switch rate goes down substantially (by 35%!) with commit
ab23a77687, which also implies that the lock contention is resulting in much longer spin and/or sleep times on the lock.Quoted 6 lines
I'm not sure we can do anything about this in the filesystem. The contended lock is a core, high level VFS lock which is the first point of
unlinkat()syscall serialisation. This is the lock that is directly exposed to userspace concurrency, so the scalability of this lock determines concurrency performance of the userspace application.....Thanks for explanation! It makes sense, except one difference I can see in vmstat on both marvin7 and dobby which I don't understand:
Dobby:
Ops Sector Reads 1009081.00 1009081.00
Ops Sector Writes 11550795.00 18753764.00Marvin7:
Ops Sector Reads 887951.00 887951.00
Ops Sector Writes 8248822.00 11135086.00Quoted 6 lines
So after the change reaim ends up doing noticeably more writes. I had a look at iostat comparison as well but there wasn't anything particular standing out besides higher amount of writes on the test disk. I guess, I'll limit the number of clients to a single number showing the regression, enable some more detailed monitoring and see whether something interesting pops up.
Interesting.
There weren't iostats in the original intel profiles given. I can see a couple of vmstats that give some indications - vmstat.io.bo went up from ~2500 to ~6000, and proc-vmstat.pgpgout went up from ~90k to 250k.
Looking at another more recent profile, there are more IO related stats in the output vmstat.nr_written went up by 2.5x and vmstat.pgpgout went up by a factor of 6 (50k -> 300k) but otherwise everything else was fairly constant in the VM. The resident size of the file cache is small, and vmstat.nr_dirtied went up by a small ammount by it's 4 orders of magnitude larger than
nr_written.Hmmm. That implies a *lot* of overwrite of cached files.
I wonder if we've just changed the memory pressure enough to trigger more frequent writeback? We're delaying the inactivation (and hence page cache invalidation) of up to 256 inodes per CPU, and the number of cached+dirty inodes appears to have increased a small amount (from ~3000 to ~4000). With slow disks, a small change in writeback behaviour could cause seek-bound related performance regressions.
Also worth noting is that there's been some recent variance in reaim numbers recently because of the journal FUA/flush optimisations we've made. Some machines report +20% from that change, some report -20%, and there's no pattern to it. It's just another indication that the reaim scalability and perf on these large CPU count, single spinning disk setups is highly dependent on disk performance and seek optimisation...
Quoted 2 lines
Have you run any tests on a system that isn't stupidly overpowered for it's disk subsystem? e.g. has an SSD rather than spinning rust?
So marvin7 actually has SSD. I was experimenting some more. Attached is a simple reproducer that demonstrates the issue for me - it just creates 16k file, fsync it, delete it in a loop from given number processes (I run with 48). The reproducer runs ~25% slower after the commit
ab23a77687. Note that the reproducer makes each process use a different directory soi_rwsemcontention is out of question.
Quoted 3 lines
From blktrace I can see that indeed after the commit we do ~25% more writes. Each stress-unlink process does the same amount of IO, the extra IO comes solely from the worker threads.
So the question is "which worker thread?".
Quoted 4 lines
Also I'd note that before the
commit we were reusing blocks much more (likely inode blocks getting reused) - before the commit we write to ~88 MB worth of distinct disk blocks, after the commit we write to ~296 MB worth of distinct disk blocks.
Hmmm, I didn't see this at first. What's the filesystem layout (xfs_info) and the CLI for the test that you ran? How many CPUs was the test run on?
Running a test with 100 procs across 32p, so creating 100 dirs and 10000 files, on a 1.4TB SSD:
$ xfs_info /mnt/scratch
meta-data=/dev/mapper/fast isize=512 agcount=67, agsize=5467072 blks
= sectsz=512 attr=2, projid32bit=1
= crc=1 finobt=1, sparse=1, rmapbt=0
= reflink=1
data = bsize=4096 blocks=366292480, imaxpct=5
= sunit=64 swidth=256 blks
naming =version 2 bsize=4096 ascii-ci=0, ftype=1
log =internal log bsize=4096 blocks=512000, version=2
= sectsz=512 sunit=1 blks, lazy-count=1
realtime =none extsz=4096 blocks=0, rtextents=0
$ ./stress-unlink 100 /mnt/scratch
0.301
$The total number of inode cluster writes is:
$ pminfo -f xfs.icluster_flushcnt
xfs.icluster_flushcnt
value 68
That's 68 * 32kB or about 2MB.
[pminfo is part of Performance Co-Pilot - https://pcp.io/]
We did this many user writes:
$ pminfo -f xfs.write xfs.write_bytes
xfs.write
value 10000
xfs.write_bytes
value 163840000which is 160MB in 10000 writes.
Metadata writeback was:
$ pminfo -f xfs.log_tail.push_ail.success
xfs.log_tail.push_ail.success
value 473
473 buffers, part of which was 68 inode clusters so the total is about ~400 x 4kB + 2MB = 3.6MB.
So, really, there isn't a potential for 25% growth in these numbers that would make any sort of difference. The only remaining source of IO differential is log writes:
$ pminfo -f xfs.log
xfs.log.writes
value 1055
xfs.log.blocks
value 28212....
Which indicates another ~1000 IOs and ~28MB written.
And that's it. We've got a total of about 195MB written to disk for 100 concurrent runs, and it's no different before and after deferred inactivation. Other tests that I commonly run that do lots of file creates and unlinks along with sync writes (e.g. dbench) didn't show any regressions up to 512 concurrent processes, either. So there's no obvious regression on this filesystem layout....
But it made me wonder - there are two things that could influence background inactivation here: the AG count (which determines unlink concurrency) and log size (which determines transaction concurrency). So I remade the filesystem with a tiny 32MB log and 2 AGs, and that changed a -lot-:
xfs.icluster_flushcnt
value 40420
xfs.log_tail.push_ail.success
value 46098
Yeah, we did 40,000 inode cluster writes for only 10000 inode modifications. Basically, we wrote every inode cluster once for every inode modification (post create, post write, post unlink, post deferred activation). Normally create/unlink loops the inode doesn't even touch the disk - it's cancelled in the log before it gets flushed to disk and so this is where a chunk of the difference in disk space consumed comes from. It can be expected behaviour.
xfs.log_tail.push_ail.pinned
value 84381
And we hit pinned items in the AIL 85,000 times instead of 0. This triggers more log forces, but fsync is already doing that so it's not a big deal. However:
xfs.log_tail.try_logspace
value 80392
xfs.log_tail.sleep_logspace
value 59938
75% of the operations had to wait on log space, which means it's forcing the log tail to flush metadata to make space. That's where all the inode cluster writes are coming from - the transactions are lock stepping on log space. i.e. every time we want to modify an inode, we have to flush a dirty inode to make space in the log.
This also means that the CIL can't perform efficient in-memory transaction aggregation because it's always being forced out to disk. As a result:
xfs.log.writes
value 6504
xfs.log.blocks
value 657846x as many log writes, for 65MB of log writes. IOWs, the smaller log reduced CIL aggregation efficiency substantially and so we wrote twice as much to the log just because we had a small log.
So, the question needs to be asked: is this a function of a small log, or is this behaviour of low AG count?
Increasing AG count back out to > CPU count resulted in the number of inode cluster flushes dropping to ~3000, and the log writes dropping back down to 1000 and 28MB of log writes. Performance went way up, too (from 1.8s down to 0.35s), indicating that AG concurrency is a factor here.
OTOH, leaving the AG count at 2 and increasing the log back out to 2GB removed all the log space waiting, all the inode cluster flushing, and everything to do with waiting on log space. But performance barely changed (1.8s down to 1.5s) and log bandwidth *went up*:
xfs.log.writes
value 6528
xfs.log.blocks
value 135452
6,500 log writes, 130MB written to the log. IOWs, both too-small log space and too-low AG count for the given workload concurrency will adversely affect performance of concurrent workloads.
But we already knew that, didn't we? :/
Bumping the AG count from 2 to 16 and using a moderately sized log (i.e. > 100MB) largely erases the bad behaviour. Indeed, agcount=16, log size=100MB drops runtime to 0.30s and pretty much returns inode write count and log write/bw back down to minimums on this 100 process workload.
But to point out that this isn't perfect for everything, if I run the same test with 1000 processes on that config, it takes 6.2s, writes 400MB to the log and flushes 153,000 inode clusters. We're back to not having enough log space for the workload. Bumping out to agcount=67 (2x CPU count) and max log size(2GB) results in runtime of 3.5s (largely linear from the 100 process count), no inode writeback and only 200MB of log throughput.
So, yeah, I suspect that if you change the mkfs parameters for the reaim tests to have more AGs and significantly increased log space over the defaults, the regression should disappear...
Can you run these experiments with reaim on your test machines and see if they are influenced by filesystem level concurrency parameters like AG count and log size as these tests suggest?
Cheers,
Dave.
Signature · 2 lines
Dave Chinner [email protected]
Quoted 104 lines · Dave Chinner
Quoted 103 lines · Jan Kara
Quoted 92 lines · Dave Chinner
Quoted 53 lines · Jan Kara
Quoted 34 lines · Dave Chinner
Quoted 8 lines · Jan Kara
Hello,
our performance testing grid has detected a performance regression caused by commit
ab23a77687("xfs: per-cpu deferred inode inactivation queues") with reaim benchmark running 'disk' and 'disk-large' workloads. The regression has been so far detected on two machines - marvin7 (48 cpus, 64 GB ram, SATA SSD), dobby (64 cpus, 192 GB ram, rotating disk behindmegaraid_sascontroller).Yup, large cpu count, single slow disk, and the cause will likely be exclusive rwsem lock contention on a directory inode that concurrent openat and unlink are occuring in.
Basically, that commit removed a bunch of userspace overhead in unlinks, when mean they run as fast as the
unlink()call can remove the directory entry. There is effectively nothing throttlingunlink()in XFS now except for available log space and it mostly runs to completion without blocking. Hence the front end unlink performance can run in much faster bursts before delayed inactivation needs to run.Given most of the added CPU overhead is in the rwsem
spin_on_ownerpath, it implies that the write lock holder is, indeed, not sleeping with the lock held. Hence reaim is hitting a borderline contended rwsem much harder and with different behaviour, resulting in catastrophic breakdown of lock performance and hence unlink performance goes backwards.I can't see any other new sleeping lock contention in the workload profiles - the context switch rate goes down substantially (by 35%!) with commit
ab23a77687, which also implies that the lock contention is resulting in much longer spin and/or sleep times on the lock.Quoted 6 lines
I'm not sure we can do anything about this in the filesystem. The contended lock is a core, high level VFS lock which is the first point of
unlinkat()syscall serialisation. This is the lock that is directly exposed to userspace concurrency, so the scalability of this lock determines concurrency performance of the userspace application.....Thanks for explanation! It makes sense, except one difference I can see in vmstat on both marvin7 and dobby which I don't understand:
Dobby:
Ops Sector Reads 1009081.00 1009081.00
Ops Sector Writes 11550795.00 18753764.00Marvin7:
Ops Sector Reads 887951.00 887951.00
Ops Sector Writes 8248822.00 11135086.00Quoted 6 lines
So after the change reaim ends up doing noticeably more writes. I had a look at iostat comparison as well but there wasn't anything particular standing out besides higher amount of writes on the test disk. I guess, I'll limit the number of clients to a single number showing the regression, enable some more detailed monitoring and see whether something interesting pops up.
Interesting.
There weren't iostats in the original intel profiles given. I can see a couple of vmstats that give some indications - vmstat.io.bo went up from ~2500 to ~6000, and proc-vmstat.pgpgout went up from ~90k to 250k.
Looking at another more recent profile, there are more IO related stats in the output vmstat.nr_written went up by 2.5x and vmstat.pgpgout went up by a factor of 6 (50k -> 300k) but otherwise everything else was fairly constant in the VM. The resident size of the file cache is small, and vmstat.nr_dirtied went up by a small ammount by it's 4 orders of magnitude larger than
nr_written.Hmmm. That implies a *lot* of overwrite of cached files.
I wonder if we've just changed the memory pressure enough to trigger more frequent writeback? We're delaying the inactivation (and hence page cache invalidation) of up to 256 inodes per CPU, and the number of cached+dirty inodes appears to have increased a small amount (from ~3000 to ~4000). With slow disks, a small change in writeback behaviour could cause seek-bound related performance regressions.
Also worth noting is that there's been some recent variance in reaim numbers recently because of the journal FUA/flush optimisations we've made. Some machines report +20% from that change, some report -20%, and there's no pattern to it. It's just another indication that the reaim scalability and perf on these large CPU count, single spinning disk setups is highly dependent on disk performance and seek optimisation...
Quoted 2 lines
Have you run any tests on a system that isn't stupidly overpowered for it's disk subsystem? e.g. has an SSD rather than spinning rust?
So marvin7 actually has SSD. I was experimenting some more. Attached is a simple reproducer that demonstrates the issue for me - it just creates 16k file, fsync it, delete it in a loop from given number processes (I run with 48). The reproducer runs ~25% slower after the commit
ab23a77687. Note that the reproducer makes each process use a different directory soi_rwsemcontention is out of question.
Quoted 5 lines
Quoted 3 lines
From blktrace I can see that indeed after the commit we do ~25% more writes. Each stress-unlink process does the same amount of IO, the extra IO comes solely from the worker threads.
So the question is "which worker thread?".
Yes, I'm also wondering ;) But it's impossible to tell from block traces (there's just "kworker/xx:x" there).
Quoted 8 lines
Quoted 4 lines
Also I'd note that before the
commit we were reusing blocks much more (likely inode blocks getting reused) - before the commit we write to ~88 MB worth of distinct disk blocks, after the commit we write to ~296 MB worth of distinct disk blocks.Hmmm, I didn't see this at first. What's the filesystem layout (
xfs_info) and the CLI for the test that you ran? How many CPUs was the test run on?
The machine has 24 cores, each core has 2 SMT siblings, so 48 logical CPUs. That's why I've run stress-unlink with 48 processes.
xfs_info is:
meta-data=/dev/sdb1 isize=512 agcount=4, agsize=29303104 blks
= sectsz=512 attr=2, projid32bit=1
= crc=1 finobt=1, sparse=0, rmapbt=0
= reflink=0
data = bsize=4096 blocks=117212416, imaxpct=25
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0, ftype=1
log =internal log bsize=4096 blocks=57232, version=2
= sectsz=512 sunit=0 blks, lazy-count=1
realtime =none extsz=4096 blocks=0, rtextents=0This is whatever are XFS defaults (with somewhat dated xfsprogs on this machine - 4.15.0), I didn't pass any special parameters to mkfs.xfs.
Quoted 168 lines
Running a test with 100 procs across 32p, so creating 100 dirs and 10000 files, on a 1.4TB SSD:
$ xfs_info /mnt/scratch meta-data=/dev/mapper/fast isize=512 agcount=67, agsize=5467072 blks = sectsz=512 attr=2, projid32bit=1 = crc=1 finobt=1, sparse=1, rmapbt=0 = reflink=1 data = bsize=4096 blocks=366292480, imaxpct=5 = sunit=64 swidth=256 blks naming =version 2 bsize=4096 ascii-ci=0, ftype=1 log =internal log bsize=4096 blocks=512000, version=2 = sectsz=512 sunit=1 blks, lazy-count=1 realtime =none extsz=4096 blocks=0, rtextents=0 $ ./stress-unlink 100 /mnt/scratch 0.301 $The total number of inode cluster writes is:
$ pminfo -f xfs.icluster_flushcntxfs.icluster_flushcnt
value 68That's 68 * 32kB or about 2MB.
[pminfo is part of Performance Co-Pilot - https://pcp.io/]
We did this many user writes:
$ pminfo -f xfs.write xfs.write_bytesxfs.write
value 10000 xfs.write_bytes value 163840000which is 160MB in 10000 writes.
Metadata writeback was:
$ pminfo -f xfs.log_tail.push_ail.successxfs.log_tail.push_ail.success
value 473473 buffers, part of which was 68 inode clusters so the total is about ~400 x 4kB + 2MB = 3.6MB.
So, really, there isn't a potential for 25% growth in these numbers that would make any sort of difference. The only remaining source of IO differential is log writes:
$ pminfo -f xfs.logxfs.log.writes
value 1055 xfs.log.blocks value 28212....
Which indicates another ~1000 IOs and ~28MB written.
And that's it. We've got a total of about 195MB written to disk for 100 concurrent runs, and it's no different before and after deferred inactivation. Other tests that I commonly run that do lots of file creates and unlinks along with sync writes (e.g. dbench) didn't show any regressions up to 512 concurrent processes, either. So there's no obvious regression on this filesystem layout....
But it made me wonder - there are two things that could influence background inactivation here: the AG count (which determines unlink concurrency) and log size (which determines transaction concurrency). So I remade the filesystem with a tiny 32MB log and 2 AGs, and that changed a -lot-:
xfs.icluster_flushcnt
value 40420xfs.log_tail.push_ail.success
value 46098Yeah, we did 40,000 inode cluster writes for only 10000 inode modifications. Basically, we wrote every inode cluster once for every inode modification (post create, post write, post unlink, post deferred activation). Normally create/unlink loops the inode doesn't even touch the disk - it's cancelled in the log before it gets flushed to disk and so this is where a chunk of the difference in disk space consumed comes from. It can be expected behaviour.
xfs.log_tail.push_ail.pinned
value 84381And we hit pinned items in the AIL 85,000 times instead of 0. This triggers more log forces, but fsync is already doing that so it's not a big deal. However:
xfs.log_tail.try_logspace
value 80392xfs.log_tail.sleep_logspace
value 5993875% of the operations had to wait on log space, which means it's forcing the log tail to flush metadata to make space. That's where all the inode cluster writes are coming from - the transactions are lock stepping on log space. i.e. every time we want to modify an inode, we have to flush a dirty inode to make space in the log.
This also means that the CIL can't perform efficient in-memory transaction aggregation because it's always being forced out to disk. As a result:
xfs.log.writes
value 6504 xfs.log.blocks value 657846x as many log writes, for 65MB of log writes. IOWs, the smaller log reduced CIL aggregation efficiency substantially and so we wrote twice as much to the log just because we had a small log.
So, the question needs to be asked: is this a function of a small log, or is this behaviour of low AG count?
Increasing AG count back out to > CPU count resulted in the number of inode cluster flushes dropping to ~3000, and the log writes dropping back down to 1000 and 28MB of log writes. Performance went way up, too (from 1.8s down to 0.35s), indicating that AG concurrency is a factor here.
OTOH, leaving the AG count at 2 and increasing the log back out to 2GB removed all the log space waiting, all the inode cluster flushing, and everything to do with waiting on log space. But performance barely changed (1.8s down to 1.5s) and log bandwidth *went up*:
xfs.log.writes
value 6528xfs.log.blocks
value 1354526,500 log writes, 130MB written to the log. IOWs, both too-small log space and too-low AG count for the given workload concurrency will adversely affect performance of concurrent workloads.
But we already knew that, didn't we? :/
Bumping the AG count from 2 to 16 and using a moderately sized log (i.e. > 100MB) largely erases the bad behaviour. Indeed, agcount=16, log size=100MB drops runtime to 0.30s and pretty much returns inode write count and log write/bw back down to minimums on this 100 process workload.
But to point out that this isn't perfect for everything, if I run the same test with 1000 processes on that config, it takes 6.2s, writes 400MB to the log and flushes 153,000 inode clusters. We're back to not having enough log space for the workload. Bumping out to agcount=67 (2x CPU count) and max log size(2GB) results in runtime of 3.5s (largely linear from the 100 process count), no inode writeback and only 200MB of log throughput.
Quoted 7 lines
So, yeah, I suspect that if you change the mkfs parameters for the reaim tests to have more AGs and significantly increased log space over the defaults, the regression should disappear...
Can you run these experiments with reaim on your test machines and see if they are influenced by filesystem level concurrency parameters like AG count and log size as these tests suggest?
Thanks for the detailed analysis and suggestions. So here are some numbers from my end. First, note that I've bumped number of unlinks each process does from 100 to 1000 so that runtime on the test machine gets above 1s to avoid some random noise. The relative slowdown (25%) didn't change (I did it already yesterday but sent stress-unlink version without bumped up loop count). Exact time to complete of stress-unlink are (from 5 runs):
(default mkfs params - agcount=4, logsize=223MB)
AVG STDDEV
before 2.7952 0.022886
after 3.4746 0.025303
I did also runs with increased AG count (to 96) and log size (to 512 MB). The results are somewhat surprising:
(agcount=96, logsize=512MB)
AVG STDDEV
before 3.1340 0.044168
after 3.3612 0.048412
So the change did somewhat help the case with deferred inactivation however it significantly hurt the kernel before deferred inactivation. Overall we are still far from original performance.
I had a look at xfs stats (full stats are attached for 4 different configs
- (before / after) * (defaults / high ag count)) and logging stats are clearly different:
defaults-before:
log 4700 157590 0 48585 71854
defaults-after:
log 10293 536643 6 48007 53762
highag-before:
log 5933 233065 0 48000 58240
highag-after:
log 6789 303249 0 48155 53795
We can see big differences in the amount of log writes as well as logged blocks. defaults-before logged 76 MB, defaults-after logged 262 MB, highag-before logged 113 MB, highag-after logged 148 MB. Given data writes for this test are 750 MB (16k * 48 processes * 1000 loops), the difference of 186 MB of log IO matches well with the observed difference in the amount of writes in block traces.
I'm not sure why the amount of logged blocks differs so much. I didn't find big difference between various configs in push_ail stats. However I did find notable differences in various btree stats:
defaults-before:
abtb2 99580 228864 15129 15129 0 0 0 0 0 0 0 0 0 0 49616 abtc2 229903 464130 96526 96526 0 0 0 0 0 0 0 0 0 0 299055 ibt2 96099 96096 3 3 0 0 0 0 0 0 0 0 0 0 0
fibt2 96099 96096 3 3 0 0 0 0 0 0 0 0 0 0 0
defaults-after:
abtb2 95532 400144 36596 36441 0 0 0 0 0 0 0 0 0 0 1421782 abtc2 157421 667273 61135 60980 0 0 0 0 0 0 0 0 0 0 1935106 ibt2 95420 220423 51 34 0 0 0 0 0 0 0 0 0 0 1 fibt2 131505 230219 7708 7691 0 0 0 0 0 0 0 0 0 0 40470
highag-before:
abtb2 120143 240191 24047 24047 0 0 0 0 0 0 0 0 0 0 0 abtc2 288334 456240 120143 120143 0 0 0 0 0 0 0 0 0 0 24051 ibt2 96143 96096 47 47 0 0 0 0 0 0 0 0 0 0 0
fibt2 96143 96096 47 47 0 0 0 0 0 0 0 0 0 0 0
highag-after:
abtb2 96903 205361 20137 20117 0 0 0 0 0 0 0 0 0 0 101850 abtc2 211742 433347 81617 81597 0 0 0 0 0 0 0 0 0 0 274068 ibt2 96083 96035 48 47 0 0 0 0 0 0 0 0 0 0 0 fibt2 96083 96035 48 47 0 0 0 0 0 0 0 0 0 0 0
So we seem to be shuffling btrees more in the slower configurations.
Honza
Signature · 2 lines
Jan Kara <[email protected]> SUSE Labs, CR
extent_alloc 48004 192025 48004 192025
abt 0 0 0 0blk_map 48073 96001 48001 96001 48001 288076 0 bmbt 0 0 0 0
dir 96 48048 48048 0
trans 0 384280 0
ig 48048 47952 2 96 0 0 0
log 4700 157590 0 48585 71854push_ail 384280 0 289 8 0 101 0 18 0 1
xstrat 48000 0
rw 48000 0
attr 0 0 0 0
icluster 0 4 20
vnodes 97 0 0 0 48048 48048 48048 0
buf 768796 24 768772 138553 41272 24 0 20 17 abtb2 99580 228864 15129 15129 0 0 0 0 0 0 0 0 0 0 49616 abtc2 229903 464130 96526 96526 0 0 0 0 0 0 0 0 0 0 299055 bmbt2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ibt2 96099 96096 3 3 0 0 0 0 0 0 0 0 0 0 0
fibt2 96099 96096 3 3 0 0 0 0 0 0 0 0 0 0 0 rmapbt 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
refcntbt 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
qm 0 0 0 0 0 0 0 0 0
xpc 786432000 786432000 0defer_relog 0
debug 0
extent_alloc 48052 192409 47308 189365
abt 0 0 0 0blk_map 48073 96001 47274 96001 47274 287349 0 bmbt 0 0 0 0
dir 96 48048 48048 0
trans 0 381555 0
ig 48048 46076 0 1972 0 1245 0
log 10293 536643 6 48007 53762push_ail 381555 0 413 68 0 36 0 1028 0 6
xstrat 48000 0
rw 48000 0
attr 0 0 0 0
icluster 0 36 1123
vnodes 728 0 0 0 48048 48048 48048 0
buf 846870 121 846749 89673 27864 121 0 117 18 abtb2 95532 400144 36596 36441 0 0 0 0 0 0 0 0 0 0 1421782 abtc2 157421 667273 61135 60980 0 0 0 0 0 0 0 0 0 0 1935106 bmbt2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ibt2 95420 220423 51 34 0 0 0 0 0 0 0 0 0 0 1 fibt2 131505 230219 7708 7691 0 0 0 0 0 0 0 0 0 0 40470 rmapbt 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
refcntbt 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
qm 0 0 0 0 0 0 0 0 0
xpc 786432000 786432000 0defer_relog 0
debug 0
extent_alloc 48048 192377 48048 192377
abt 0 0 0 0blk_map 48073 96001 48001 96001 48001 288076 0 bmbt 0 0 0 0
dir 96 48048 48048 0
trans 0 384677 0
ig 48048 47952 0 96 0 0 0
log 5933 233065 0 48000 58240push_ail 384677 0 0 0 0 0 0 0 0 0
xstrat 48000 0
rw 48000 0
attr 0 0 0 0
icluster 0 0 0
vnodes 97 0 0 0 48048 48048 48048 0
buf 769219 288 768931 0 0 288 0 240 193
abtb2 120143 240191 24047 24047 0 0 0 0 0 0 0 0 0 0 0 abtc2 288334 456240 120143 120143 0 0 0 0 0 0 0 0 0 0 24051 bmbt2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ibt2 96143 96096 47 47 0 0 0 0 0 0 0 0 0 0 0
fibt2 96143 96096 47 47 0 0 0 0 0 0 0 0 0 0 0 rmapbt 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
refcntbt 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
qm 0 0 0 0 0 0 0 0 0
xpc 786432000 786432000 0defer_relog 0
debug 0
extent_alloc 48049 192385 47987 192133
abt 0 0 0 0blk_map 48050 96001 47940 96001 47940 287992 0 bmbt 0 0 0 0
dir 48 48048 48048 0
trans 0 384389 0
ig 48048 46316 0 1732 0 1671 0
log 6789 303249 0 48155 53795push_ail 384389 0 132 489 0 4 0 1633 0 1
xstrat 48000 0
rw 48000 0
attr 0 0 0 0
icluster 0 95 1716
vnodes 764 0 0 0 48048 48048 48048 0
buf 771055 97 770958 1339 250 97 0 97 0
abtb2 96903 205361 20137 20117 0 0 0 0 0 0 0 0 0 0 101850 abtc2 211742 433347 81617 81597 0 0 0 0 0 0 0 0 0 0 274068 bmbt2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ibt2 96083 96035 48 47 0 0 0 0 0 0 0 0 0 0 0 fibt2 96083 96035 48 47 0 0 0 0 0 0 0 0 0 0 0 rmapbt 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
refcntbt 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
qm 0 0 0 0 0 0 0 0 0
xpc 786432000 786432000 0defer_relog 0
debug 0
Quoted 11 lines · Jan Kara
Quoted 4 lines · Dave Chinner
On Wed, Oct 06, 2021 at 08:10:01PM +0200, Jan Kara wrote:
Hmmm, I didn't see this at first. What's the filesystem layout (xfs_info) and the CLI for the test that you ran? How many CPUs was the test run on?The machine has 24 cores, each core has 2 SMT siblings, so 48 logical CPUs. That's why I've run stress-unlink with 48 processes.
xfs_infois:
Quoted 8 lines
meta-data=/dev/sdb1 isize=512 agcount=4, agsize=29303104 blks
= sectsz=512 attr=2, projid32bit=1
= crc=1 finobt=1, sparse=0, rmapbt=0
= reflink=0
data = bsize=4096 blocks=117212416, imaxpct=25
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0, ftype=1
log =internal log bsize=4096 blocks=57232, version=2OK, default log is ~230MB, fs size is ~400GB?
Quoted 28 lines
Quoted 8 lines
But to point out that this isn't perfect for everything, if I run the same test with 1000 processes on that config, it takes 6.2s, writes 400MB to the log and flushes 153,000 inode clusters. We're back to not having enough log space for the workload. Bumping out to agcount=67 (2x CPU count) and max log size(2GB) results in runtime of 3.5s (largely linear from the 100 process count), no inode writeback and only 200MB of log throughput.
Quoted 7 lines
So, yeah, I suspect that if you change the mkfs parameters for the reaim tests to have more AGs and significantly increased log space over the defaults, the regression should disappear...
Can you run these experiments with reaim on your test machines and see if they are influenced by filesystem level concurrency parameters like AG count and log size as these tests suggest?
Thanks for the detailed analysis and suggestions. So here are some numbers from my end. First, note that I've bumped number of unlinks each process does from 100 to 1000 so that runtime on the test machine gets above 1s to avoid some random noise. The relative slowdown (25%) didn't change (I did it already yesterday but sent stress-unlink version without bumped up loop count). Exact time to complete of stress-unlink are (from 5 runs):
(default mkfs params - agcount=4, logsize=223MB)
AVG STDDEV
before 2.7952 0.022886
after 3.4746 0.025303
Quoted 7 lines
I did also runs with increased AG count (to 96) and log size (to 512 MB). The results are somewhat surprising:
(agcount=96, logsize=512MB)
AVG STDDEV
before 3.1340 0.044168
after 3.3612 0.048412
You bumped the log size to 512MB, but then bumped the amount of work by a factor of 10....
Quoted 10 lines
So the change did somewhat help the case with deferred inactivation however it significantly hurt the kernel before deferred inactivation. Overall we are still far from original performance.
I had a look at xfs stats (full stats are attached for 4 different configs
- (before / after) * (defaults / high ag count)) and logging stats are clearly different:defaults-before:
log 4700 157590 0 48585 71854
Fits in < 75% of log space, so will not be pushing out metadata at all during the test.
Quoted 2 lines
defaults-after:
log 10293 536643 6 48007 53762
Overwrites the log 2.5x, so limited by metadata writeback speed for most of the test.
Quoted 2 lines
highag-before:
log 5933 233065 0 48000 58240
Yup, workload is spread across 16x more AGs and AG metadata, so I'd expect to see such an increase in log throuhgput. But with a larger log, this won't be tail-pushing...
Quoted 2 lines
highag-after:
log 6789 303249 0 48155 53795
And this is also under the tail-pushing threshold, so really the only difference in perf here comes from writing more metadata to the log.
Quoted 8 lines
We can see big differences in the amount of log writes as well as logged blocks. defaults-before logged 76 MB, defaults-after logged 262 MB, highag-before logged 113 MB, highag-after logged 148 MB. Given data writes for this test are 750 MB (16k * 48 processes * 1000 loops), the difference of 186 MB of log IO matches well with the observed difference in the amount of writes in block traces.
I'm not sure why the amount of logged blocks differs so much.
fsync() interactions.
On the original code, the two unlink transactions are temporally adjacent as both are in unlinkat() syscall context. One is directly run by the syscall, the other in task_run context at syscall exit when processing the last reference of the file being dropped.
In general, that means the objects modified (inode cluster, AGI, inode, etc) are captured by the same CIL context and so aggregate in memory as a single change (essentially log dedupe). Then the next fsync() from some other context runs, pushing the CIL to disk and we only log those objects modified in unlink to the journal once.
With deferred activation, the two phases of unlink are temporally decoupled. We get a bunch of inodes running the first phase in unlink() context, but the second phase is run later in a tight loop from workqueue context. But this means that fsync()s occur between the two pahses, and hence the objects modified in the two phases of unlink are modified in two separate CIL contexts. Hence they get written to the log twice.
Depending on the way things work out, deferred inactivation also results in longer unlinked inode chains, resulting in more objects being logged per unlink than without deferred inactivation, as the inodes are added to the unlink chain and then immediately removed before any others are added. Hence deferred inode inactivation will increase the amount written to the log per unlink if the two phases of unlink as split across journal checkpoints.
IOWs, an increase in log writes for open-write-fsync-close-unlink workloads is not unexpected. But this workload isn't really a real world workload in any way - we generally don't do data integrity writes only to immediately throw the data away. :/
Remove the fsync and we do have a real world workload - temporary files for compiles, etc. Then everything should mostly get logged in the same CIL context because all transactions are run asynchronously and aggregate in memory until the CIL is full and checkpoints itself. Hence log writes shouldn't change very much at all for such workloads.
Quoted 10 lines
I didn't find
big difference between various configs inpush_ailstats. However I did find notable differences in various btree stats:defaults-before:
abtb2 99580 228864 15129 15129 0 0 0 0 0 0 0 0 0 0 49616 abtc2 229903 464130 96526 96526 0 0 0 0 0 0 0 0 0 0 299055 ibt2 96099 96096 3 3 0 0 0 0 0 0 0 0 0 0 0
fibt2 96099 96096 3 3 0 0 0 0 0 0 0 0 0 0 0
Quoted 5 lines
defaults-after:
abtb2 95532 400144 36596 36441 0 0 0 0 0 0 0 0 0 0 1421782 abtc2 157421 667273 61135 60980 0 0 0 0 0 0 0 0 0 0 1935106 ibt2 95420 220423 51 34 0 0 0 0 0 0 0 0 0 0 1 fibt2 131505 230219 7708 7691 0 0 0 0 0 0 0 0 0 0 40470
Yup, the change in the finobt is indicative of slight changes in order of allocate/free of inodes. We're tracking a more free inode records because we aren't doing purely sequential inode allocation and freeing due to AGI contention managing the unlinked inode chain.
IOWs, we've previously hyper-optimised create-unlink workloads to aggressively reuse inodes, and that resulted in rapid reuse of the unlinked inodes. That still happens, but deferred inactivation increases the pool of free inodes that is being cycled over by this workload. This reflects the per-ag contention occurring in this limited fs config - we're getting larger batches of unlinked inodes being chained on the AGs and so when they are freed we see more inodes being added to the finobt and then reallocated from there.
I have plans to further decouple the unlinked AGI chain updates between the two phases of unlink that will help address this, but that is future work and not ready to go yet.
Quoted 11 lines
highag-before:
abtb2 120143 240191 24047 24047 0 0 0 0 0 0 0 0 0 0 0 abtc2 288334 456240 120143 120143 0 0 0 0 0 0 0 0 0 0 24051 ibt2 96143 96096 47 47 0 0 0 0 0 0 0 0 0 0 0
fibt2 96143 96096 47 47 0 0 0 0 0 0 0 0 0 0 0highag-after:
abtb2 96903 205361 20137 20117 0 0 0 0 0 0 0 0 0 0 101850 abtc2 211742 433347 81617 81597 0 0 0 0 0 0 0 0 0 0 274068 ibt2 96083 96035 48 47 0 0 0 0 0 0 0 0 0 0 0 fibt2 96083 96035 48 47 0 0 0 0 0 0 0 0 0 0 0
With this, we have no AGI contention to speak of between the two phases of unlink, so unlinked inode chains remain very short in both cases and so we don't see any change to finobt residency.
Cheers,
Dave.
Signature · 2 lines
Dave Chinner [email protected]
Quoted 21 lines · Dave Chinner
Quoted 11 lines · Jan Kara
Quoted 4 lines · Dave Chinner
On Wed, Oct 06, 2021 at 08:10:01PM +0200, Jan Kara wrote:
Hmmm, I didn't see this at first. What's the filesystem layout (xfs_info) and the CLI for the test that you ran? How many CPUs was the test run on?The machine has 24 cores, each core has 2 SMT siblings, so 48 logical CPUs. That's why I've run stress-unlink with 48 processes.
xfs_infois:Quoted 8 lines
meta-data=/dev/sdb1 isize=512 agcount=4, agsize=29303104 blks = sectsz=512 attr=2, projid32bit=1 = crc=1 finobt=1, sparse=0, rmapbt=0 = reflink=0 data = bsize=4096 blocks=117212416, imaxpct=25 = sunit=0 swidth=0 blks naming =version 2 bsize=4096 ascii-ci=0, ftype=1 log =internal log bsize=4096 blocks=57232, version=2
Quoted 1 line
OK, default log is ~230MB, fs size is ~400GB?
Yep.
<snip log analysis>
Quoted 43 lines
Quoted 8 lines
We can see big differences in the amount of log writes as well as logged blocks. defaults-before logged 76 MB, defaults-after logged 262 MB, highag-before logged 113 MB, highag-after logged 148 MB. Given data writes for this test are 750 MB (16k * 48 processes * 1000 loops), the difference of 186 MB of log IO matches well with the observed difference in the amount of writes in block traces.
I'm not sure why the amount of logged blocks differs so much.
fsync()interactions.On the original code, the two unlink transactions are temporally adjacent as both are in
unlinkat()syscall context. One is directly run by the syscall, the other intask_runcontext at syscall exit when processing the last reference of the file being dropped.In general, that means the objects modified (inode cluster, AGI, inode, etc) are captured by the same CIL context and so aggregate in memory as a single change (essentially log dedupe). Then the next
fsync()from some other context runs, pushing the CIL to disk and we only log those objects modified in unlink to the journal once.With deferred activation, the two phases of unlink are temporally decoupled. We get a bunch of inodes running the first phase in
unlink()context, but the second phase is run later in a tight loop from workqueue context. But this means that fsync()s occur between the two pahses, and hence the objects modified in the two phases of unlink are modified in two separate CIL contexts. Hence they get written to the log twice.Depending on the way things work out, deferred inactivation also results in longer unlinked inode chains, resulting in more objects being logged per unlink than without deferred inactivation, as the inodes are added to the unlink chain and then immediately removed before any others are added. Hence deferred inode inactivation will increase the amount written to the log per unlink if the two phases of unlink as split across journal checkpoints.
IOWs, an increase in log writes for open-write-fsync-close-unlink workloads is not unexpected. But this workload isn't really a real world workload in any way - we generally don't do data integrity writes only to immediately throw the data away. :/
Quoted 6 lines
Remove the fsync and we do have a real world workload - temporary files for compiles, etc. Then everything should mostly get logged in the same CIL context because all transactions are run asynchronously and aggregate in memory until the CIL is full and checkpoints itself. Hence log writes shouldn't change very much at all for such workloads.
OK, that makes sense. Thanks for explanation. So to verify your theory, I've removed fsync(2) from the test program. So now it is pure create, write, unlink workload. Results of "stress-unlink 48 /mnt", now for 5000 loops of create-unlink to increase runtime (but the workload does barely any writes so it should not matter wrt log):
default mkfs params:
AVG STDDEV
before 2.0380 0.1597
after 2.7356 0.4712
agcount=96, log size 512M
AVG STDDEV
before 1.0610 0.0227
after 1.2508 0.0218
So still notable regression with the async inactivation. With default mkfs params we'd need more runs to get more reliable results (note the rather high standard deviation) but with high AG count results show pretty stable 20% regression - so let's have a look at that.
Looking at xfs stats there are barely any differences between before & after - 'after' writes a bit more to the log but it is ~1.5 MB over the whole benchmark run, altogether spending some 8ms doing IO so that's not it. Generally the workload seems to be CPU / memory bound now (it does barely any IO). Perf shows we are heavily contending on some spinlock in xfs_cil_commit() - I presume this is a xc_cil_lock. This actually happens both before and after, but we seem to spend some more time there with async inactivation. Likely this is related to work being done from worker threads. Perf stats for comparison:
before
51,135.08 msec cpu-clock # 47.894 CPUs utilized
4,699 context-switches # 0.092 K/sec
382 cpu-migrations # 0.007 K/sec
1,228 page-faults # 0.024 K/sec
128,884,972,351 cycles # 2.520 GHz
38,517,767,839 instructions # 0.30 insn per cycle
8,337,611,468 branches # 163.051 M/sec
39,749,736 branch-misses # 0.48% of all branches
25,225,109 cache-misses
1.067666170 seconds time elapsedafter
65,353.43 msec cpu-clock # 47.894 CPUs utilized
43,737 context-switches # 0.669 K/sec
1,824 cpu-migrations # 0.028 K/sec
1,953 page-faults # 0.030 K/sec
155,144,150,867 cycles # 2.374 GHz
45,280,145,337 instructions # 0.29 insn per cycle
10,027,567,384 branches # 153.436 M/sec
39,554,691 branch-misses # 0.39% of all branches
30,203,567 cache-misses
1.364539400 seconds time elapsedSo we can see huge increase in context-switches, notable increase in cache-misses, decrease in cycles/s so perhaps we are bouncing cache more? Anyway I guess this is kind of expected due to the nature of async inactivation, I just wanted to highlight that there are regressions without fsync in the game as well.
Honza
Signature · 2 lines
Jan Kara <[email protected]> SUSE Labs, CR
Quoted 99 lines · Jan Kara
Quoted 21 lines · Dave Chinner
Quoted 11 lines · Jan Kara
Quoted 4 lines · Dave Chinner
On Wed, Oct 06, 2021 at 08:10:01PM +0200, Jan Kara wrote:
Hmmm, I didn't see this at first. What's the filesystem layout (xfs_info) and the CLI for the test that you ran? How many CPUs was the test run on?The machine has 24 cores, each core has 2 SMT siblings, so 48 logical CPUs. That's why I've run stress-unlink with 48 processes.
xfs_infois:Quoted 8 lines
meta-data=/dev/sdb1 isize=512 agcount=4, agsize=29303104 blks = sectsz=512 attr=2, projid32bit=1 = crc=1 finobt=1, sparse=0, rmapbt=0 = reflink=0 data = bsize=4096 blocks=117212416, imaxpct=25 = sunit=0 swidth=0 blks naming =version 2 bsize=4096 ascii-ci=0, ftype=1 log =internal log bsize=4096 blocks=57232, version=2Quoted 1 line
OK, default log is ~230MB, fs size is ~400GB?
Yep.
<snip log analysis>
Quoted 43 lines
Quoted 8 lines
We can see big differences in the amount of log writes as well as logged blocks. defaults-before logged 76 MB, defaults-after logged 262 MB, highag-before logged 113 MB, highag-after logged 148 MB. Given data writes for this test are 750 MB (16k * 48 processes * 1000 loops), the difference of 186 MB of log IO matches well with the observed difference in the amount of writes in block traces.
I'm not sure why the amount of logged blocks differs so much.
fsync()interactions.On the original code, the two unlink transactions are temporally adjacent as both are in
unlinkat()syscall context. One is directly run by the syscall, the other intask_runcontext at syscall exit when processing the last reference of the file being dropped.In general, that means the objects modified (inode cluster, AGI, inode, etc) are captured by the same CIL context and so aggregate in memory as a single change (essentially log dedupe). Then the next
fsync()from some other context runs, pushing the CIL to disk and we only log those objects modified in unlink to the journal once.With deferred activation, the two phases of unlink are temporally decoupled. We get a bunch of inodes running the first phase in
unlink()context, but the second phase is run later in a tight loop from workqueue context. But this means that fsync()s occur between the two pahses, and hence the objects modified in the two phases of unlink are modified in two separate CIL contexts. Hence they get written to the log twice.Depending on the way things work out, deferred inactivation also results in longer unlinked inode chains, resulting in more objects being logged per unlink than without deferred inactivation, as the inodes are added to the unlink chain and then immediately removed before any others are added. Hence deferred inode inactivation will increase the amount written to the log per unlink if the two phases of unlink as split across journal checkpoints.
IOWs, an increase in log writes for open-write-fsync-close-unlink workloads is not unexpected. But this workload isn't really a real world workload in any way - we generally don't do data integrity writes only to immediately throw the data away. :/
Quoted 6 lines
Remove the fsync and we do have a real world workload - temporary files for compiles, etc. Then everything should mostly get logged in the same CIL context because all transactions are run asynchronously and aggregate in memory until the CIL is full and checkpoints itself. Hence log writes shouldn't change very much at all for such workloads.
OK, that makes sense. Thanks for explanation. So to verify your theory, I've removed fsync(2) from the test program. So now it is pure create, write, unlink workload. Results of "stress-unlink 48 /mnt", now for 5000 loops of create-unlink to increase runtime (but the workload does barely any writes so it should not matter wrt log):
default mkfs params:
AVG STDDEV
before 2.0380 0.1597
after 2.7356 0.4712agcount=96, log size 512M
AVG STDDEV
before 1.0610 0.0227
after 1.2508 0.0218So still notable regression with the async inactivation. With default mkfs params we'd need more runs to get more reliable results (note the rather high standard deviation) but with high AG count results show pretty stable 20% regression - so let's have a look at that.
Quoted 6 lines
Looking at xfs stats there are barely any differences between before & after - 'after' writes a bit more to the log but it is ~1.5 MB over the whole benchmark run, altogether spending some 8ms doing IO so that's not it. Generally the workload seems to be CPU / memory bound now (it does barely any IO). Perf shows we are heavily contending on some spinlock in
xfs_cil_commit()- I presume this is axc_cil_lock.
Yes, and I have patches that fix this. It got reverted a before release because it exposed a bunch of underlying zero-fay bugs in the log code, and I haven't had time to run it through the review cycle again even though it's pretty much unchanged from commits 26-39 in this series:
https://lore.kernel.org/linux-xfs/[email protected]/
The profiles in this patch demonstrate the problem and the fix:
https://lore.kernel.org/linux-xfs/[email protected]/
I did all my perf testing of inode inactivation with the CIL scalability patches also installed, because deferred inode inactivation only made contention on the CIL lock worse in my perf tests. We simply can't evaluate the benefit of a change when the system is easily driven into catastrophic lock breakdown by user level operational concurrency.
IOWs, the CIL lock is the global limiting factor for async transaction commit rates on large CPU count machines, and things that remove bottlenecks in higher layers often just increase contention on this lock and drive it into breakdown. That makes perf go backwards, not forwards, and it's not the fault of the high level change being made. That doesn't make the high level change wrong, it just means we need to peel the onion further before the improvements are fully realised.
Quoted 31 lines
This actually happens
both before and after, but we seem to spend some more time there with async inactivation. Likely this is related to work being done from worker threads. Perf stats for comparison:before
51,135.08 msec cpu-clock # 47.894 CPUs utilized 4,699 context-switches # 0.092 K/sec 382 cpu-migrations # 0.007 K/sec 1,228 page-faults # 0.024 K/sec 128,884,972,351 cycles # 2.520 GHz 38,517,767,839 instructions # 0.30 insn per cycle 8,337,611,468 branches # 163.051 M/sec 39,749,736 branch-misses # 0.48% of all branches 25,225,109 cache-misses 1.067666170 seconds time elapsedafter
65,353.43 msec cpu-clock # 47.894 CPUs utilized 43,737 context-switches # 0.669 K/sec 1,824 cpu-migrations # 0.028 K/sec 1,953 page-faults # 0.030 K/sec 155,144,150,867 cycles # 2.374 GHz 45,280,145,337 instructions # 0.29 insn per cycle 10,027,567,384 branches # 153.436 M/sec 39,554,691 branch-misses # 0.39% of all branches 30,203,567 cache-misses 1.364539400 seconds time elapsed
Quoted 5 lines
So we can see huge increase in context-switches, notable increase in cache-misses, decrease in cycles/s so perhaps we are bouncing cache more? Anyway I guess this is kind of expected due to the nature of async inactivation, I just wanted to highlight that there are regressions without fsync in the game as well.
Context switches are largely noise - they are most likely just AGI locks being bounced a bit more. It's the spinlock contention that is the likely issue here. For example, on my 32p machine with vanilla 5.15-rc4 with a fsync-less, 5000 iteration test run:
$ sudo perf_5.9 stat ./stress-unlink 32 /mnt/scratch Processes started. 1.290
Performance counter stats for './stress-unlink 32 /mnt/scratch':
16,856.61 msec task-clock # 12.595 CPUs utilized
48,297 context-switches # 0.003 M/sec
4,219 cpu-migrations # 0.250 K/sec
1,373 page-faults # 0.081 K/sec
39,254,798,526 cycles # 2.329 GHz
16,460,808,349 instructions # 0.42 insn per cycle
3,475,251,228 branches # 206.166 M/sec
12,129,889 branch-misses # 0.35% of all branches 1.338312347 seconds time elapsed
0.186554000 seconds user
17.247176000 seconds sysAnd with 5.15-rc4 + CIL scalability:
$ sudo perf_5.9 stat ./stress-unlink 32 /mnt/scratch Processes started. 0.894
Performance counter stats for './stress-unlink 32 /mnt/scratch':
12,917.93 msec task-clock # 13.805 CPUs utilized
39,680 context-switches # 0.003 M/sec
2,737 cpu-migrations # 0.212 K/sec
1,402 page-faults # 0.109 K/sec
30,920,293,752 cycles # 2.394 GHz
14,472,067,501 instructions # 0.47 insn per cycle
2,700,978,247 branches # 209.087 M/sec
9,287,754 branch-misses # 0.34% of all branches 0.935710173 seconds time elapsed
0.192467000 seconds user
13.245977000 seconds sysRuntime of the fsync-less, 5,000 iteration version drops from 1.29s to 0.89s, IPC goes up, branches and branch-misses go down, context switches only go down slightly, etc. IOWs, when you take away the CIL lock contention, we get back all that perf loss and then some...
FWIW, let's really hammer it for a long while. Vanilla 5.14-rc4:
$ sudo perf_5.9 stat ./stress-unlink 1000 /mnt/scratch Processes started. 38.881
Performance counter stats for './stress-unlink 1000 /mnt/scratch':
733,741.06 msec task-clock # 16.004 CPUs utilized
13,131,968 context-switches # 0.018 M/sec
1,302,636 cpu-migrations # 0.002 M/sec
40,720 page-faults # 0.055 K/sec
1,195,192,185,398 cycles # 1.629 GHz
643,382,890,656 instructions # 0.54 insn per cycle
129,065,409,600 branches # 175.900 M/sec
768,146,988 branch-misses # 0.60% of all branches 45.847750477 seconds time elapsed
11.194020000 seconds user
758.762376000 seconds sysAnd the transaction rate is pinned at 800,000/s for the entire test. We're running at the limit of the CIL lock here.
With CIL scalbility patchset:
$ sudo perf_5.9 stat ./stress-unlink 1000 /mnt/scratch Processes started. 28.263
Performance counter stats for './stress-unlink 1000 /mnt/scratch':
450,547.80 msec task-clock # 15.038 CPUs utilized
5,949,268 context-switches # 0.013 M/sec
868,887 cpu-migrations # 0.002 M/sec
41,570 page-faults # 0.092 K/sec
836,933,822,425 cycles # 1.858 GHz
536,132,522,275 instructions # 0.64 insn per cycle
99,264,579,180 branches # 220.320 M/sec
506,921,132 branch-misses # 0.51% of all branches 29.961492616 seconds time elapsed
7.796758000 seconds user
471.990545000 seconds sys30% reduction in runtime because the transaction rate is now running at 1.1M/s. Improvements in code execution across the board here, so the problem clearly isn't the deferred inode inactivation.
IOWs, I'm largely not concerned about the high CPU count perf regressions that we are seeing from log code these days - the fix is largely ready, it's just lacking in available engineering time to get it over the line and merged right now...
Cheers,
Dave.
Signature · 2 lines
Dave Chinner [email protected]
Quoted 56 lines · Dave Chinner
Quoted 29 lines · Jan Kara
Quoted 6 lines · Dave Chinner
Remove the fsync and we do have a real world workload - temporary files for compiles, etc. Then everything should mostly get logged in the same CIL context because all transactions are run asynchronously and aggregate in memory until the CIL is full and checkpoints itself. Hence log writes shouldn't change very much at all for such workloads.
OK, that makes sense. Thanks for explanation. So to verify your theory, I've removed fsync(2) from the test program. So now it is pure create, write, unlink workload. Results of "stress-unlink 48 /mnt", now for 5000 loops of create-unlink to increase runtime (but the workload does barely any writes so it should not matter wrt log):
default mkfs params:
AVG STDDEV
before 2.0380 0.1597
after 2.7356 0.4712agcount=96, log size 512M
AVG STDDEV
before 1.0610 0.0227
after 1.2508 0.0218So still notable regression with the async inactivation. With default mkfs params we'd need more runs to get more reliable results (note the rather high standard deviation) but with high AG count results show pretty stable 20% regression - so let's have a look at that.
Quoted 6 lines
Looking at xfs stats there are barely any differences between before & after - 'after' writes a bit more to the log but it is ~1.5 MB over the whole benchmark run, altogether spending some 8ms doing IO so that's not it. Generally the workload seems to be CPU / memory bound now (it does barely any IO). Perf shows we are heavily contending on some spinlock in
xfs_cil_commit()- I presume this is axc_cil_lock.Yes, and I have patches that fix this. It got reverted a before release because it exposed a bunch of underlying zero-fay bugs in the log code, and I haven't had time to run it through the review cycle again even though it's pretty much unchanged from commits 26-39 in this series:
https://lore.kernel.org/linux-xfs/[email protected]/
The profiles in this patch demonstrate the problem and the fix:
https://lore.kernel.org/linux-xfs/[email protected]/
I did all my perf testing of inode inactivation with the CIL scalability patches also installed, because deferred inode inactivation only made contention on the CIL lock worse in my perf tests. We simply can't evaluate the benefit of a change when the system is easily driven into catastrophic lock breakdown by user level operational concurrency.
Quoted 8 lines
IOWs, the CIL lock is the global limiting factor for async transaction commit rates on large CPU count machines, and things that remove bottlenecks in higher layers often just increase contention on this lock and drive it into breakdown. That makes perf go backwards, not forwards, and it's not the fault of the high level change being made. That doesn't make the high level change wrong, it just means we need to peel the onion further before the improvements are fully realised.
OK, understood.
Quoted 84 lines
Quoted 31 lines
This actually happens
both before and after, but we seem to spend some more time there with async inactivation. Likely this is related to work being done from worker threads. Perf stats for comparison:before
51,135.08 msec cpu-clock # 47.894 CPUs utilized 4,699 context-switches # 0.092 K/sec 382 cpu-migrations # 0.007 K/sec 1,228 page-faults # 0.024 K/sec 128,884,972,351 cycles # 2.520 GHz 38,517,767,839 instructions # 0.30 insn per cycle 8,337,611,468 branches # 163.051 M/sec 39,749,736 branch-misses # 0.48% of all branches 25,225,109 cache-misses 1.067666170 seconds time elapsedafter
65,353.43 msec cpu-clock # 47.894 CPUs utilized 43,737 context-switches # 0.669 K/sec 1,824 cpu-migrations # 0.028 K/sec 1,953 page-faults # 0.030 K/sec 155,144,150,867 cycles # 2.374 GHz 45,280,145,337 instructions # 0.29 insn per cycle 10,027,567,384 branches # 153.436 M/sec 39,554,691 branch-misses # 0.39% of all branches 30,203,567 cache-misses 1.364539400 seconds time elapsedQuoted 5 lines
So we can see huge increase in context-switches, notable increase in cache-misses, decrease in cycles/s so perhaps we are bouncing cache more? Anyway I guess this is kind of expected due to the nature of async inactivation, I just wanted to highlight that there are regressions without fsync in the game as well.
Context switches are largely noise - they are most likely just AGI locks being bounced a bit more. It's the spinlock contention that is the likely issue here. For example, on my 32p machine with vanilla 5.15-rc4 with a fsync-less, 5000 iteration test run:
$ sudo perf_5.9 stat ./stress-unlink 32 /mnt/scratch Processes started. 1.290Performance counter stats for './stress-unlink 32
/mnt/scratch':16,856.61 msec task-clock # 12.595 CPUs utilized 48,297 context-switches # 0.003 M/sec 4,219 cpu-migrations # 0.250 K/sec 1,373 page-faults # 0.081 K/sec 39,254,798,526 cycles # 2.329 GHz 16,460,808,349 instructions # 0.42 insn per cycle 3,475,251,228 branches # 206.166 M/sec 12,129,889 branch-misses # 0.35% of all branches1.338312347 seconds time elapsed 0.186554000 seconds user 17.247176000 seconds sysAnd with 5.15-rc4 + CIL scalability:
$ sudo perf_5.9 stat ./stress-unlink 32 /mnt/scratch Processes started. 0.894Performance counter stats for './stress-unlink 32
/mnt/scratch':12,917.93 msec task-clock # 13.805 CPUs utilized 39,680 context-switches # 0.003 M/sec 2,737 cpu-migrations # 0.212 K/sec 1,402 page-faults # 0.109 K/sec 30,920,293,752 cycles # 2.394 GHz 14,472,067,501 instructions # 0.47 insn per cycle 2,700,978,247 branches # 209.087 M/sec 9,287,754 branch-misses # 0.34% of all branches0.935710173 seconds time elapsed 0.192467000 seconds user 13.245977000 seconds sys
Quoted 4 lines
Runtime of the fsync-less, 5,000 iteration version drops from 1.29s to 0.89s, IPC goes up, branches and branch-misses go down, context switches only go down slightly, etc. IOWs, when you take away the CIL lock contention, we get back all that perf loss and then some...
Nice results!
Quoted 48 lines
FWIW, let's really hammer it for a long while. Vanilla 5.14-rc4:
$ sudo perf_5.9 stat ./stress-unlink 1000 /mnt/scratch Processes started. 38.881Performance counter stats for './stress-unlink 1000
/mnt/scratch':733,741.06 msec task-clock # 16.004 CPUs utilized 13,131,968 context-switches # 0.018 M/sec 1,302,636 cpu-migrations # 0.002 M/sec 40,720 page-faults # 0.055 K/sec 1,195,192,185,398 cycles # 1.629 GHz 643,382,890,656 instructions # 0.54 insn per cycle 129,065,409,600 branches # 175.900 M/sec 768,146,988 branch-misses # 0.60% of all branches45.847750477 seconds time elapsed 11.194020000 seconds user 758.762376000 seconds sysAnd the transaction rate is pinned at 800,000/s for the entire test. We're running at the limit of the CIL lock here.
With CIL scalbility patchset:
$ sudo perf_5.9 stat ./stress-unlink 1000 /mnt/scratch Processes started. 28.263Performance counter stats for './stress-unlink 1000
/mnt/scratch':450,547.80 msec task-clock # 15.038 CPUs utilized 5,949,268 context-switches # 0.013 M/sec 868,887 cpu-migrations # 0.002 M/sec 41,570 page-faults # 0.092 K/sec 836,933,822,425 cycles # 1.858 GHz 536,132,522,275 instructions # 0.64 insn per cycle 99,264,579,180 branches # 220.320 M/sec 506,921,132 branch-misses # 0.51% of all branches29.961492616 seconds time elapsed 7.796758000 seconds user 471.990545000 seconds sys
Quoted 8 lines
30% reduction in runtime because the transaction rate is now running at 1.1M/s. Improvements in code execution across the board here, so the problem clearly isn't the deferred inode inactivation.
IOWs, I'm largely not concerned about the high CPU count perf regressions that we are seeing from log code these days - the fix is largely ready, it's just lacking in available engineering time to get it over the line and merged right now...
OK, thanks for explanation!
Honza
Signature · 2 lines
Jan Kara <[email protected]> SUSE Labs, CR