net/i40e: disable source pruning
PATCH 1/1 net/i40e: disable source pruning
VRRP advertisement packets are dropped on i40e PF devices because when a MAC address is added to a device, packets originating from that MAC address are dropped. This patch disables source pruning to work around that issue.
--- drivers/net/i40e/i40e_ethdev.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/net/i40e/i40e_ethdev.c +4 -0
@@ -5812,6 +5812,10 @@ struct i40e_vsi * ctxt.pf_num = hw->pf_id; ctxt.uplink_seid = vsi->uplink_seid; ctxt.vf_num =0 ; + ctxt.info.valid_sections |= +cpu_to_le16 (I40E_AQ_VSI_PROP_SWITCH_VALID ); + ctxt.info.switch_id |= +cpu_to_le16 (I40E_AQ_VSI_SW_ID_FLAG_LOCAL_LB );/* Update VSI parameters */ ret =i40e_aq_update_vsi_params (hw, &ctxt,NULL );
Signature · 1 line
1.8.3.1
PATCH v2 1/1 net/i40e: disable source pruning
VRRP advertisement packets are dropped on i40e PF devices because when a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a devarg to support disabling source pruning to work around above issue.
--- doc/guides/nics/i40e.rst | 9 ++++++ drivers/net/i40e/i40e_ethdev.c | 65 ++++++++++++++++++++++++++++++++++++++++++ drivers/net/i40e/i40e_ethdev.h | 1 + 3 files changed, 75 insertions(+)
doc/guides/nics/i40e.rst +9 -0
@@ -236,6 +236,15 @@ Runtime Config Options -a 84:00.0,vf_msg_cfg=80@120:180 +- ``Disable source pruning on PF`` (default ``not disabled``) + + When a MAC address is added to a device, packets originating from that MAC + address will be dropped for source pruning. To disable source pruning on PF + we can add ``devargs`` parameter ``disable_source_pruning=[0,1]`` and set its + value to 1, for example:: + + -a 84:00.0,disable_source_pruning=1 + Vector RX Pre-conditions ~~~~~~~~~~~~~~~~~~~~~~~~ For Vector RX it is assumed that the number of descriptor rings will be a power
drivers/net/i40e/i40e_ethdev.c +65 -0
101 lines not on this page · raw message
drivers/net/i40e/i40e_ethdev.h +1 -0
@@ -1171,6 +1171,7 @@ struct i40e_pf {bool dport_replace_flag;/* Destination port replace is done */ struct i40e_tm_conf tm_conf;bool support_multi_driver;/* 1 - support multiple driver */ +bool disable_source_pruning;/* 1 - disable source pruning */ /* Dynamic Device Personalization */ bool gtp_support;/* 1 - support GTP-C and GTP-U */
Signature · 1 line
1.8.3.1
PATCH v3 1/1 net/i40e: disable source pruning
VRRP advertisement packets are dropped on i40e PF devices because when a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a devarg to support disabling source pruning to work around above issue.
Bugzilla ID: 648
---
v3: Rebase to 69a3c6319140. Add bugzilla ID in commit log.
--- doc/guides/nics/i40e.rst | 9 ++++++ drivers/net/i40e/i40e_ethdev.c | 65 ++++++++++++++++++++++++++++++++++++++++++ drivers/net/i40e/i40e_ethdev.h | 1 + 3 files changed, 75 insertions(+)
doc/guides/nics/i40e.rst +9 -0
@@ -236,6 +236,15 @@ Runtime Config Options -a 84:00.0,vf_msg_cfg=80@120:180 +- ``Disable source pruning on PF`` (default ``not disabled``) + + When a MAC address is added to a device, packets originating from that MAC + address will be dropped for source pruning. To disable source pruning on PF + we can add ``devargs`` parameter ``disable_source_pruning=[0,1]`` and set its + value to 1, for example:: + + -a 84:00.0,disable_source_pruning=1 + Vector RX Pre-conditions ~~~~~~~~~~~~~~~~~~~~~~~~ For Vector RX it is assumed that the number of descriptor rings will be a power
drivers/net/i40e/i40e_ethdev.c +65 -0
101 lines not on this page · raw message
drivers/net/i40e/i40e_ethdev.h +1 -0
@@ -1171,6 +1171,7 @@ struct i40e_pf {bool dport_replace_flag;/* Destination port replace is done */ struct i40e_tm_conf tm_conf;bool support_multi_driver;/* 1 - support multiple driver */ +bool disable_source_pruning;/* 1 - disable source pruning */ /* Dynamic Device Personalization */ bool gtp_support;/* 1 - support GTP-C and GTP-U */
Signature · 1 line
1.8.3.1
Quoted 12 lines
-----Original Message-----
From: dev <[email protected]> On Behalf Of Alvin Zhang
Sent: Wednesday, October 20, 2021 9:29 AM
To: Xing, Beilei <[email protected]>; Guo, Junfeng <[email protected]>
Cc: [email protected]; Zhang, AlvinX <[email protected]>
Subject: [dpdk-dev] [PATCH v3] net/i40e: disable source pruningVRRP advertisement packets are dropped on i40e PF devices because when a MAC address is added to a device, packets originating from that MAC address are dropped.
Quoted 7 lines
This patch adds a devarg to support disabling source pruning to work around above issue.
Bugzilla ID: 648
Signed-off-by Alvin Zhang <[email protected]>---
Verified patchset http://patches.dpdk.org/project/dpdk/patch/[email protected]/ on baseline dpdk22.03-rc1:ecc0dd455e "raw/cnxk_gpio: add option to select subset of GPIOs" Tested pass on Ethernet Controller XL710 for 40GbE QSFP+ 1583, OS: Fedora Linux 35/5.14.10-300.fc35.x86_64
Test step as below:
./dpdk-testpmd -l 1,2 -n 1 -a 18:00.0,disable_source_pruning=1 -- -i
pkt = Ether(src="00:00:5E:00:01:0A")/IP()/Raw("x"*60)
test steps:
1). testpmd>set verbose 1
testpmd>start
2). Send the pkt, the pkt can be received by testpmd
3). testpmd>mac_addr add 0 00:00:5E:00:01:0A
4). Re-send the pkt, the pkt still can be received by testpmd.
Quoted 21 lines
From: Jiang, YuX [mailto:[email protected]]
Sent: Monday, 21 February 2022 09.31Quoted 4 lines
From: dev <[email protected]> On Behalf Of Alvin Zhang
Sent: Wednesday, October 20, 2021 9:29 AMVRRP advertisement packets are dropped on i40e PF devices because
when
Quoted 4 lines
a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a devarg to support disabling source pruning to work
around
Quoted 6 lines
above issue.
Bugzilla ID: 648
Signed-off-by Alvin Zhang <[email protected]>---
Tested-by Yu Jiang <[email protected]>
Quoted 15 lines
Verified patchset
http://patches.dpdk.org/project/dpdk/patch/20211020012831.8480-1-
[email protected]/ on baseline dpdk22.03-rc1:ecc0dd455e "raw/cnxk_gpio: add option to select subset of GPIOs" Tested pass on Ethernet Controller XL710 for 40GbE QSFP+ 1583, OS:
Fedora Linux 35/5.14.10-300.fc35.x86_64
Test step as below:
./dpdk-testpmd -l 1,2 -n 1 -a 18:00.0,disable_source_pruning=1 -- -i pkt = Ether(src="00:00:5E:00:01:0A")/IP()/Raw("x"*60) test steps:
1). testpmd>set verbose 1
testpmd>start
2). Send the pkt, the pkt can be received by testpmd
3). testpmd>mac_addr add 0 00:00:5E:00:01:0A
4). Re-send the pkt, the pkt still can be received by testpmd.
If source pruning is not the default behavior of all NICs, it should be disabled by default in the i40e NIC too.
A NIC shouldn't drop any packets unless it has explicitly been configured for it! And a NIC shouldn't treat any packets differently than other NICs do, unless the NIC has explicitly been configured so!
Furthermore, I would prefer that configurations for explicitly dropping certain types of packets is available through runtime APIs, e.g. RTE_FLOWS, or dedicated functions like rte_eth_promiscuous_enable/disable(). This patch doesn't support runtime detection of installed NICs performed by the application.
I am very surprised by this default behavior of a NIC. Please confirm that Source Pruning is at least disabled in Promiscuous mode?
-Morten
Quoted 59 lines
-----Original Message-----
From: Morten Brørup <[email protected]>
Sent: Monday, February 21, 2022 5:35 PM
To: Jiang, YuX <[email protected]>; Alvin Zhang <[email protected]>; Xing, Beilei <[email protected]>; Guo, Junfeng <[email protected]>
Cc: [email protected]; Zhang, AlvinX <[email protected]>
Subject: RE: [dpdk-dev] [PATCH v3] net/i40e: disable source pruningQuoted 21 lines
From: Jiang, YuX [mailto:[email protected]]
Sent: Monday, 21 February 2022 09.31Quoted 4 lines
From: dev <[email protected]> On Behalf Of Alvin Zhang
Sent: Wednesday, October 20, 2021 9:29 AMVRRP advertisement packets are dropped on i40e PF devices because
when
Quoted 4 lines
a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a devarg to support disabling source pruning to work
around
Quoted 6 lines
above issue.
Bugzilla ID: 648
Signed-off-by Alvin Zhang <[email protected]>---
Tested-by Yu Jiang <[email protected]>Quoted 14 lines
Verified patchset
http://patches.dpdk.org/project/dpdk/patch/20211020012831.8480-1-
[email protected]/ on baseline dpdk22.03-rc1:ecc0dd455e "raw/cnxk_gpio: add option to select subset of GPIOs" Tested pass on Ethernet Controller XL710 for 40GbE QSFP+ 1583, OS:
Fedora Linux 35/5.14.10-300.fc35.x86_64 Test step as below:
./dpdk-testpmd -l 1,2 -n 1 -a 18:00.0,disable_source_pruning=1 -- -i
pkt = Ether(src="00:00:5E:00:01:0A")/IP()/Raw("x"*60)
test steps:
1). testpmd>set verbose 1
testpmd>start
2). Send the pkt, the pkt can be received by testpmd 3). testpmd>mac_addr add 0 00:00:5E:00:01:0A 4). Re-send the pkt, the pkt still can be received by testpmd.If source pruning is not the default behavior of all NICs, it should be disabled by default in the i40e NIC too.
A NIC shouldn't drop any packets unless it has explicitly been configured for it! And a NIC shouldn't treat any packets differently than other NICs do, unless the NIC has explicitly been configured so!
Furthermore, I would prefer that configurations for explicitly dropping certain types of packets is available through runtime APIs, e.g.
RTE_FLOWS, or dedicated functions like rte_eth_promiscuous_enable/disable(). This patch doesn't support runtime detection of installed NICs performed by the application.
Quoted 4 lines
I am very surprised by this default behavior of a NIC. Please confirm that Source Pruning is at least disabled in Promiscuous mode?
-Morten
Thanks for your comments @Morten Brørup
After testing with other NIC like ice, source pruning is the default action, it means it is the same action for both ice and i40e when receiving in default.
In this patch, the default is "not disable", it is same with other NICs.
+CC Ethernet API maintainers, you might have an opinion about expected default behavior
Quoted 67 lines
From: Zhang, Ke1X [mailto:[email protected]]
Sent: Monday, 26 December 2022 10.04Quoted 15 lines
From: Morten Brørup <[email protected]>
Sent: Monday, February 21, 2022 5:35 PMQuoted 12 lines
From: Jiang, YuX [mailto:[email protected]]
Sent: Monday, 21 February 2022 09.31Quoted 4 lines
From: dev <[email protected]> On Behalf Of Alvin Zhang
Sent: Wednesday, October 20, 2021 9:29 AMVRRP advertisement packets are dropped on i40e PF devices because
when
Quoted 4 lines
a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a devarg to support disabling source pruning to
work
Quoted 9 lines
Quoted 9 lines
around
Quoted 6 lines
above issue.
Bugzilla ID: 648
Signed-off-by Alvin Zhang <[email protected]>---
Tested-by Yu Jiang <[email protected]>Quoted 7 lines
Quoted 7 lines
Verified patchset
http://patches.dpdk.org/project/dpdk/patch/20211020012831.8480-1-
[email protected]/ on baseline dpdk22.03-rc1:ecc0dd455e "raw/cnxk_gpio: add option to select subset of GPIOs" Tested pass on Ethernet Controller XL710 for 40GbE QSFP+ 1583, OS:
Fedora Linux 35/5.14.10-300.fc35.x86_64 Test step as below:
./dpdk-testpmd -l 1,2 -n 1 -a 18:00.0,disable_source_pruning=1 ---i
Quoted 6 lines
Quoted 6 lines
pkt = Ether(src="00:00:5E:00:01:0A")/IP()/Raw("x"*60)
test steps:
1). testpmd>set verbose 1
testpmd>start
2). Send the pkt, the pkt can be received by testpmd 3). testpmd>mac_addr add 0 00:00:5E:00:01:0A 4). Re-send the pkt, thepkt
Quoted 3 lines
Quoted 1 line
still can be received by testpmd.
If source pruning is not the default behavior of all NICs, it should
be disabled
Quoted 3 lines
by default in the i40e NIC too.
A NIC shouldn't drop any packets unless it has explicitly been
configured for it!
Quoted 1 line
And a NIC shouldn't treat any packets differently than other NICs do,
unless
Quoted 3 lines
the NIC has explicitly been configured so!
Furthermore, I would prefer that configurations for explicitly
dropping
Quoted 1 line
certain types of packets is available through runtime APIs, e.g.
RTE_FLOWS,Quoted 1 line
or dedicated functions like rte_eth_promiscuous_enable/disable().
This
Quoted 1 line
patch doesn't support runtime detection of installed NICs performed
by the
Quoted 3 lines
application.
I am very surprised by this default behavior of a NIC. Please confirm
that
Quoted 8 lines
Quoted 3 lines
Source Pruning is at least disabled in Promiscuous mode?
-Morten
Thanks for your comments @Morten Brørup
After testing with other NIC like ice, source pruning is the default action, it means it is the same action
for both ice and i40e when receiving in default.
I meant NICs in general, not just Intel NICs. Is it standard behavior for NICs in general (incl. NVIDIA, Broadcom, etc.) to perform source pruning?
They way I read the bug report, the source pruning behavior is specific to Intel NICs. Applications should not be required to pass specific command line parameters to make one vendor's PMDs behave like the general behavior of PMDs from other vendors.
Quoted 2 lines
In this patch, the default is "not disable", it is same with other NICs.
Not other NICs in general, only other Intel NICs.
I acknowledge that this patch is a workaround, and certainly an improvement, but why not provide a fix instead? It could be backported to older DPDK releases.
If you want to stick with this workaround instead of providing a proper fix, please also update the documentation to mention that disable_source_pruning=1 is required.
Please also describe how to disable source pruning at runtime. Some applications detect the installed NICs at runtime, so passing NIC specific parameters to the application at startup is not possible.
-Morten
Quoted 67 lines
From: Zhang, Ke1X [mailto:[email protected]]
Sent: Monday, 26 December 2022 10.04Quoted 15 lines
From: Morten Brørup <[email protected]>
Sent: Monday, February 21, 2022 5:35 PMQuoted 12 lines
From: Jiang, YuX [mailto:[email protected]]
Sent: Monday, 21 February 2022 09.31Quoted 4 lines
From: dev <[email protected]> On Behalf Of Alvin Zhang
Sent: Wednesday, October 20, 2021 9:29 AMVRRP advertisement packets are dropped on i40e PF devices because
when
Quoted 4 lines
a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a devarg to support disabling source pruning to
work
Quoted 9 lines
Quoted 9 lines
around
Quoted 6 lines
above issue.
Bugzilla ID: 648
Signed-off-by Alvin Zhang <[email protected]>---
Tested-by Yu Jiang <[email protected]>Quoted 7 lines
Quoted 7 lines
Verified patchset
http://patches.dpdk.org/project/dpdk/patch/20211020012831.8480-1-
[email protected]/ on baseline dpdk22.03-rc1:ecc0dd455e "raw/cnxk_gpio: add option to select subset of GPIOs" Tested pass on Ethernet Controller XL710 for 40GbE QSFP+ 1583, OS:
Fedora Linux 35/5.14.10-300.fc35.x86_64 Test step as below:
./dpdk-testpmd -l 1,2 -n 1 -a 18:00.0,disable_source_pruning=1 ---i
Quoted 6 lines
Quoted 6 lines
pkt = Ether(src="00:00:5E:00:01:0A")/IP()/Raw("x"*60)
test steps:
1). testpmd>set verbose 1
testpmd>start
2). Send the pkt, the pkt can be received by testpmd 3). testpmd>mac_addr add 0 00:00:5E:00:01:0A 4). Re-send the pkt, thepkt
Quoted 3 lines
Quoted 1 line
still can be received by testpmd.
If source pruning is not the default behavior of all NICs, it should
be disabled
Quoted 3 lines
by default in the i40e NIC too.
A NIC shouldn't drop any packets unless it has explicitly been
configured for it!
Quoted 1 line
And a NIC shouldn't treat any packets differently than other NICs do,
unless
Quoted 3 lines
the NIC has explicitly been configured so!
Furthermore, I would prefer that configurations for explicitly
dropping
Quoted 1 line
certain types of packets is available through runtime APIs, e.g.
RTE_FLOWS,Quoted 1 line
or dedicated functions like rte_eth_promiscuous_enable/disable().
This
Quoted 1 line
patch doesn't support runtime detection of installed NICs performed
by the
Quoted 3 lines
application.
I am very surprised by this default behavior of a NIC. Please confirm
that
Quoted 8 lines
Quoted 3 lines
Source Pruning is at least disabled in Promiscuous mode?
-Morten
Thanks for your comments @Morten Brørup
After testing with other NIC like ice, source pruning is the default action, it means it is the same action
for both ice and i40e when receiving in default.
I meant NICs in general, not just Intel NICs. Is it standard behavior for NICs in general (incl. NVIDIA, Broadcom, etc.) to perform source pruning?
They way I read the bug report, the source pruning behavior is specific to Intel NICs. Applications should not be required to pass specific command line parameters to make one vendor's PMDs behave like the general behavior of PMDs from other vendors.
Quoted 2 lines
In this patch, the default is "not disable", it is same with other NICs.
Not other NICs in general, only other Intel NICs.
I acknowledge that this patch is a workaround, and certainly an improvement, but why not provide a fix instead? It could be backported to older DPDK releases.
If you want to stick with this workaround instead of providing a proper fix, please also update the documentation to mention that disable_source_pruning=1 is required.
Please also describe how to disable source pruning at runtime. Some applications detect the installed NICs at runtime, so passing NIC specific parameters to the application at startup is not possible.
-Morten
PATCH 1/1 net/i40e: disable source pruning
In reply to Alvin ZhangVRRP advertisement packets are dropped on i40e PF devices because when a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a interface in lib/ethdev to support disabling source pruning to work around above issue.
Bugzilla ID: 648
--- app/test-pmd/cmdline.c | 77 ++++++++++++++++++++++++++++++++++ drivers/net/i40e/i40e_ethdev.c | 53 +++++++++++++++++++++++ lib/ethdev/ethdev_driver.h | 6 +++ lib/ethdev/rte_ethdev.c | 16 +++++++ lib/ethdev/rte_ethdev.h | 15 +++++++ 5 files changed, 167 insertions(+)
app/test-pmd/cmdline.c +77 -0
@@ -482,6 +482,9 @@ static void cmd_help_long_parsed(void *parsed_result,"set promisc (port_id|all) (on|off)\n" " Set the promiscuous mode on port_id, or all.\n\n" +"set llb (port_id|all) (on|off)\n" +" Set vsi local loopback on port_id, or all.\n\n" +"set allmulti (port_id|all) (on|off)\n" " Set the allmulti mode on port_id, or all.\n\n"
@@ -5775,6 +5778,78 @@ static cmdline_parse_inst_t cmd_set_promisc_mode_one = { }, }; +/* *** SET VSI LOCAL LOOPBACK *** */ +struct cmd_set_vsi_local_lb_result { +cmdline_fixed_string_t set; +cmdline_fixed_string_t llb; +cmdline_fixed_string_t port_all;/* valid if "allports" argument == 1 */ +uint16_t port_num;/* valid if "allports" argument == 0 */ +cmdline_fixed_string_t enable; +}; + +static void cmd_set_vsi_llb_parsed (void *parsed_result, + __rte_unused struct cmdline *cl, +void *allports) +{ +struct cmd_set_vsi_local_lb_result *res = parsed_result; +int enable; +portid_t i; + +if (!strcmp (res->enable,"on" )) + enable =1 ; +else + enable =0 ; + +/* all ports */ +if (allports) { +RTE_ETH_FOREACH_DEV (i) +rte_eth_dev_enable_local_lb (i, enable); + }else { +rte_eth_dev_enable_local_lb (res->port_num, enable); + } +} + +static cmdline_parse_token_string_t cmd_setllb_set = + TOKEN_STRING_INITIALIZER(struct cmd_set_vsi_local_lb_result, set, "set"); +static cmdline_parse_token_string_t cmd_setllb_llb = + TOKEN_STRING_INITIALIZER(struct cmd_set_vsi_local_lb_result, llb, +"llb" ); +static cmdline_parse_token_string_t cmd_setllb_portall = + TOKEN_STRING_INITIALIZER(struct cmd_set_vsi_local_lb_result, port_all, +"all" ); +static cmdline_parse_token_num_t cmd_setllb_portnum = + TOKEN_NUM_INITIALIZER(struct cmd_set_vsi_local_lb_result, port_num, +RTE_UINT16 ); +static cmdline_parse_token_string_t cmd_setllb_enalbe = + TOKEN_STRING_INITIALIZER(struct cmd_set_vsi_local_lb_result, enable, +"on#off" ); + +static cmdline_parse_inst_t cmd_set_vsi_enable_all = { + .f = cmd_set_vsi_llb_parsed, + .data = (void *)1 , + .help_str ="set llb all on|off: Set vsi local loopback for all ports" , + .tokens = { + (void *)&cmd_setllb_set, + (void *)&cmd_setllb_llb, + (void *)&cmd_setllb_portall, + (void *)&cmd_setllb_enalbe, +NULL , + }, +}; + +static cmdline_parse_inst_t cmd_set_vsi_enable_one = { + .f = cmd_set_vsi_llb_parsed, + .data = (void *)0 , + .help_str ="set llb <port_id> on|off: Set vsi local loopback on port id" , + .tokens = { + (void *)&cmd_setllb_set, + (void *)&cmd_setllb_llb, + (void *)&cmd_setllb_portnum, + (void *)&cmd_setllb_enalbe, +NULL , + }, +}; +/* *** SET ALLMULTI MODE *** */ struct cmd_set_allmulti_mode_result {cmdline_fixed_string_t set;
@@ -12866,6 +12941,8 @@ static cmdline_parse_ctx_t builtin_ctx[] = { (cmdline_parse_inst_t *)&cmd_show_port_cman_capa, (cmdline_parse_inst_t *)&cmd_show_port_cman_config, (cmdline_parse_inst_t *)&cmd_set_port_cman_config, + (cmdline_parse_inst_t *)&cmd_set_vsi_enable_all, + (cmdline_parse_inst_t *)&cmd_set_vsi_enable_one, NULL, };
drivers/net/i40e/i40e_ethdev.c +53 -0
71 lines not on this page · raw message
lib/ethdev/ethdev_driver.h +6 -0
@@ -668,6 +668,10 @@ typedef int (*eth_get_module_info_t)(struct rte_eth_dev *dev,typedef int (*eth_get_module_eeprom_t )(struct rte_eth_dev *dev,struct rte_dev_eeprom_info *info); +/** @internal Function used to enable/disable the vsi loop back of an Ethernet device. */ +typedef int (*eth_enable_local_lb_t )(struct rte_eth_dev *dev, +int on); +struct rte_flow_ops ;/** * @internal
@@ -1403,6 +1407,8 @@ struct eth_dev_ops {eth_cman_config_set_t cman_config_set;/** Retrieve congestion management configuration */ eth_cman_config_get_t cman_config_get; +/** Enable/disable the vsi loop back of an Ethernet device */ +eth_enable_local_lb_t enable_local_lb; };/**
lib/ethdev/rte_ethdev.c +16 -0
@@ -6318,6 +6318,22 @@ rte_eth_buffer_split_get_supported_hdr_ptypes(uint16_t port_id, uint32_t *ptypesreturn j; } +int +rte_eth_dev_enable_local_lb (uint16_t port_id,int on) +{ +struct rte_eth_dev *dev; +int ret; + +RTE_ETH_VALID_PORTID_OR_ERR_RET (port_id, -ENODEV ); + dev = &rte_eth_devices[port_id]; + +if (*dev->dev_ops->enable_local_lb ==NULL ) +return -ENOTSUP ; + + ret = (*dev->dev_ops->enable_local_lb)(dev, on); +return eth_err (port_id, ret); +} +RTE_LOG_REGISTER_DEFAULT (rte_eth_dev_logtype,INFO );RTE_INIT (ethdev_init_telemetry)
lib/ethdev/rte_ethdev.h +15 -0
@@ -3437,6 +3437,21 @@ int rte_eth_dev_set_mtu(uint16_t port_id, uint16_t mtu);*/ int rte_eth_dev_vlan_filter (uint16_t port_id,uint16_t vlan_id,int on); +/** +* Enable/Disable local Loopback for VSIs that are used as uplink of a software +* (cascaded) VEB, VEPA or Port Virtualizer. +* +* @param port_id +* The port identifier of the Ethernet device. +* @param on +* If > 0, enable local Loopback. +* Otherwise, disable local Loopback. +* @return +* - (0) if successful. +* - negative if failed. +*/ +int rte_eth_dev_enable_local_lb (uint16_t port_id,int on); +/** * Enable/Disable hardware VLAN Strip by a Rx queue of an Ethernet device. *
Signature · 1 line
2.25.1
+CC: Andrew, as Ethernet API maintainer
Quoted 9 lines
From: Ke Zhang [mailto:[email protected]]
Sent: Monday, 9 January 2023 03.20VRRP advertisement packets are dropped on i40e PF devices because when a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a interface in lib/ethdev to support disabling source pruning to work around above issue.
Thank you for the improved patch.
Quoted 5 lines
Bugzilla ID: 648
Signed-off-by Ke Zhang <[email protected]>---
[...]
+static cmdline_parse_token_string_t cmd_setllb_enalbe =
Typo: enalbe -> enable.
[...]
Quoted 23 lines
drivers/net/i40e/i40e_ethdev.c +9
-0+/* i40e_enable_pf_local_lb +* @pf: pointer to the pf structure +* +* allow local loopback on pf +*/ +static int +i40e_enable_pf_local_lb (struct rte_eth_dev *dev,int on) +{ + struct i40e_pf *pf = I40E_DEV_PRIVATE_TO_PF(dev->data-Quoted 1 line
dev_private);drivers/net/i40e/i40e_ethdev.c +9
-0+struct i40e_hw *hw =I40E_PF_TO_HW (pf); +struct i40e_vsi_context ctxt; +int ret; + +/* Use the FW API if FW >= v5.0 */ +if (hw->aq.fw_maj_ver <5 && hw->mac.type !=I40E_MAC_X722 ) { +#ifdef TREX_PATCH +/* Most of our customers do not have latest FW */ + PMD_INIT_LOG(INFO, "FW < v5.0, cannot enable localloopback");
(quoted diff) +2
-0+#else + PMD_INIT_LOG(ERR, "FW < v5.0, cannot enable localloopback");
drivers/net/i40e/i40e_ethdev.c i40e_enable_pf_lb(struct i40e_pf *pf) · line 5661
Quoted 3 lines
drivers/net/i40e/i40e_ethdev.c +3
-0+#endif +return I40E_NOT_SUPPORTED ; + }
Can this bug not be fixed without requiring FW >= 5.0?
If VRRP is not supported with older FW, perhaps you could also log a warning when a VRRP MAC address is added to the NIC (and the FW is too old, or local_lb is disabled). Just an idea; it will help people debug issues with VRRP in production.
Quoted 28 lines
drivers/net/i40e/i40e_ethdev.c +7
-0+ +memset (&ctxt,0 ,sizeof (ctxt)); + ctxt.seid = pf->main_vsi_seid; + ctxt.pf_num = hw->pf_id; + ret =i40e_aq_get_vsi_params (hw, &ctxt,NULL ); +if (ret) { + PMD_DRV_LOG(ERR, "cannot get pf vsi config, err %d, aq_err%d",
drivers/net/i40e/i40e_ethdev.c +20
-0+ ret, hw->aq.asq_last_status); +return ret; + } + ctxt.flags =I40E_AQ_VSI_TYPE_PF ; + ctxt.info.valid_sections = +rte_cpu_to_le_16 (I40E_AQ_VSI_PROP_SWITCH_VALID ); +if (on) + ctxt.info.switch_id |= +rte_cpu_to_le_16 (I40E_AQ_VSI_SW_ID_FLAG_LOCAL_LB ); +else + ctxt.info.switch_id &= + ~rte_cpu_to_le_16 (I40E_AQ_VSI_SW_ID_FLAG_LOCAL_LB ); + + ret =i40e_aq_update_vsi_params (hw, &ctxt,NULL ); +if (ret) +PMD_DRV_LOG (ERR ,"update vsi switch failed, aq_err=%d" , + hw->aq.asq_last_status); + +return ret; +}
[...]
Quoted 24 lines
lib/ethdev/rte_ethdev.h +2
-0@@ -3437,6 +3437,21 @@ int rte_eth_dev_set_mtu(uint16_t port_id,uint16_t mtu); */ int rte_eth_dev_vlan_filter (uint16_t port_id,uint16_t vlan_id,int on); +/** +* Enable/Disable local Loopback for VSIs that are used as uplink of a software
+ * (cascaded) VEB, VEPA or Port Virtualizer.
+ *
+ * @paramport_id
+ * The port identifier of the Ethernet device.
+ * @param on
+ * If > 0, enable local Loopback.
+ * Otherwise, disable local Loopback.
+ * @return
+ * - (0) if successful.
+ * - negative if failed.
+ */
lib/ethdev/rte_ethdev.h int rte_eth_dev_set_mtu(uint16_t port_id, uint16_t mtu); · line 3454
Quoted 2 lines
lib/ethdev/rte_ethdev.h +2
-0+int rte_eth_dev_enable_local_lb (uint16_t port_id,int on); +
Local Loopback usually means that packets queued for TX are looped back into RX by the NIC or PHY.
If the Intel X710/XXV710/XL710 "Source Pruning" feature only applies to egressing packets internally looped back to ingress by VEB, this patch makes some sense, although I wish you could come up with a better name for it than Local Loopback.
However, if the "Source Pruning" feature also applies to packets ingressing from the physical Ethernet interface, this naming and behavior is counterintuitive. In this case, "Source Pruning" is a special filter, which other NICs don't apply to ingressing packets, so the PMD should not enable the filter (and thus behave differently than all other NICs) unless explicitly enabled by the application.
Quoted 7 lines · Ke Zhang
VRRP advertisement packets are dropped on i40e PF devices because when a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a interface in lib/ethdev to support disabling source pruning to work around above issue.
Hi Ke,
We have a dilemma between enabling as much HW config/feature as possible and having common/portable APIs.
If we add a new API for each specific HW config/feature, it will be confusing for users and DPDK APIs won't be portable. We may end up slightly specific version of an API specific to a NIC.
For this we used PMD specific APIs time to time (like drivers/net/i40e/rte_pmd_i40e.h), although is not also a good solution.
If this is a common config/feature for more than one NIC, I am OK to procced with the patch as it is, for this I have cc'ed a few more folks, but first can you please describe the config/feature a little more detailed please.
What I understand is if packet target MAC address is same as device MAC address, packet is dropped, which is called 'source pruning' feature. What is the use case for this, is the expectation send a packet to router/switch and expect to receive it back?
Is all egress packets dropped as described? Becase feture referred as "local loopback" in the code, is this only applied to packets switched locally in NIC?
Can it be solution to always disable source pruning by default?
If this is specific to i40e, I suggest adding it as PMD specific API. I put some comments below but first need to clarify how to procced with the patch.
Quoted 16 lines
Bugzilla ID: 648
Signed-off-by Ke Zhang <[email protected]>--- app/test-pmd/cmdline.c | 77 ++++++++++++++++++++++++++++++++++ drivers/net/i40e/i40e_ethdev.c | 53 +++++++++++++++++++++++ lib/ethdev/ethdev_driver.h | 6 +++ lib/ethdev/rte_ethdev.c | 16 +++++++ lib/ethdev/rte_ethdev.h | 15 +++++++ 5 files changed, 167 insertions(+)app/test-pmd/cmdline.c +0
-0
app/test-pmd/cmdline.c static void cmd_help_long_parsed(void *parsed_result, · line 487
Quoted 6 lines
app/test-pmd/cmdline.c +3
-0@@ -482,6 +482,9 @@ static void cmd_help_long_parsed(void *parsed_result,"set promisc (port_id|all) (on|off)\n" " Set the promiscuous mode on port_id, or all.\n\n" +"set llb (port_id|all) (on|off)\n" +" Set vsi local loopback on port_id, or all.\n\n" +
Please don't use abreviations, specially for not commonly knows features, 'llb' won't make sense to many people, and as number of this unkown commonds increase it has a risk to make testpmd unusable, please prefer 'local_loopback'.
And please don't refer to 'vsi' here.
And personally I don't prefer using 'set xxx' commands to configure device, what I prefer:
"set xxx" --> set testpmd specific configuration
"port config <port_id> xxx" --> configure device
Although I am aware this separation is not clear and there is a mixuture of usage, some of them historical.
Quoted 67 lines
app/test-pmd/cmdline.c +60
-0"set allmulti (port_id|all) (on|off)\n" " Set the allmulti mode on port_id, or all.\n\n" @@ -5775,6 +5778,78 @@ static cmdline_parse_inst_t cmd_set_promisc_mode_one = { }, }; +/* *** SET VSI LOCAL LOOPBACK *** *> +struct cmd_set_vsi_local_lb_result { +cmdline_fixed_string_t set; +cmdline_fixed_string_t llb; +cmdline_fixed_string_t port_all; /* valid if "allports" argument == 1 */ +uint16_t port_num;/* valid if "allports" argument == 0 */ +cmdline_fixed_string_t enable; +}; + +static void cmd_set_vsi_llb_parsed (void *parsed_result, + __rte_unused struct cmdline *cl, +void *allports) +{ +struct cmd_set_vsi_local_lb_result *res = parsed_result; +int enable; +portid_t i; + +if (!strcmp (res->enable,"on" )) + enable =1 ; +else + enable =0 ; + +/* all ports */ +if (allports) { +RTE_ETH_FOREACH_DEV (i) +rte_eth_dev_enable_local_lb (i, enable); + }else { +rte_eth_dev_enable_local_lb (res->port_num, enable); + } +} + +static cmdline_parse_token_string_t cmd_setllb_set = + TOKEN_STRING_INITIALIZER(struct cmd_set_vsi_local_lb_result, set, "set"); +static cmdline_parse_token_string_t cmd_setllb_llb = + TOKEN_STRING_INITIALIZER(struct cmd_set_vsi_local_lb_result, llb, +"llb" ); +static cmdline_parse_token_string_t cmd_setllb_portall = + TOKEN_STRING_INITIALIZER(struct cmd_set_vsi_local_lb_result, port_all, +"all" ); +static cmdline_parse_token_num_t cmd_setllb_portnum = + TOKEN_NUM_INITIALIZER(struct cmd_set_vsi_local_lb_result, port_num, +RTE_UINT16 ); +static cmdline_parse_token_string_t cmd_setllb_enalbe = + TOKEN_STRING_INITIALIZER(struct cmd_set_vsi_local_lb_result, enable, +"on#off" ); + +static cmdline_parse_inst_t cmd_set_vsi_enable_all = { + .f = cmd_set_vsi_llb_parsed, + .data = (void *)1 , + .help_str ="set llb all on|off: Set vsi local loopback for all ports" , + .tokens = { + (void *)&cmd_setllb_set, + (void *)&cmd_setllb_llb, + (void *)&cmd_setllb_portall, + (void *)&cmd_setllb_enalbe, +NULL , + }, +}; + +static cmdline_parse_inst_t cmd_set_vsi_enable_one = { + .f = cmd_set_vsi_llb_parsed,
app/test-pmd/cmdline.c static cmdline_parse_inst_t cmd_set_promisc_mode_one = { · line 5850
Quoted 10 lines
app/test-pmd/cmdline.c +10
-0+ .data = (void *)0, + .help_str = "set llb <port_id> on|off: Set vsi local loopback on port id", + .tokens = { + (void *)&cmd_setllb_set, + (void *)&cmd_setllb_llb, + (void *)&cmd_setllb_portnum, + (void *)&cmd_setllb_enalbe, + NULL, + }, +};
please dont use 'vsi' in the scope of testpmd commands.
app/test-pmd/cmdline.c static cmdline_parse_ctx_t builtin_ctx[] = { · line 12945
Quoted 10 lines
app/test-pmd/cmdline.c +3
-0+/* *** SET ALLMULTI MODE *** */ struct cmd_set_allmulti_mode_result {cmdline_fixed_string_t set;@@ -12866,6 +12941,8 @@ static cmdline_parse_ctx_t builtin_ctx[] = { (cmdline_parse_inst_t *)&cmd_show_port_cman_capa, (cmdline_parse_inst_t *)&cmd_show_port_cman_config, (cmdline_parse_inst_t *)&cmd_set_port_cman_config, + (cmdline_parse_inst_t *)&cmd_set_vsi_enable_all, + (cmdline_parse_inst_t *)&cmd_set_vsi_enable_one,
Instead of adding to end better to try it grouping with relevant commands.
Quoted 86 lines
app/test-pmd/cmdline.c +0
-0NULL, };drivers/net/i40e/i40e_ethdev.c +53
-0@@ -406,6 +406,7 @@ static void i40e_ethertype_filter_restore(struct i40e_pf *pf);static void i40e_tunnel_filter_restore (struct i40e_pf *pf);static void i40e_filter_restore (struct i40e_pf *pf);static void i40e_notify_all_vfs_link_status (struct rte_eth_dev *dev); +static int i40e_enable_pf_local_lb (struct rte_eth_dev *dev,int on);static const char *const valid_keys[] = {ETH_I40E_FLOATING_VEB_ARG ,@@ -517,6 +518,7 @@ static const struct eth_dev_ops i40e_eth_dev_ops = { .tm_ops_get = i40e_tm_ops_get, .tx_done_cleanup = i40e_tx_done_cleanup, .get_monitor_addr = i40e_get_monitor_addr, + .enable_local_lb = i40e_enable_pf_local_lb, };/* store statistics names and its offset in stats structure */ @@ -5634,6 +5636,57 @@ i40e_enable_pf_lb(struct i40e_pf *pf) hw->aq.asq_last_status); } +/* i40e_enable_pf_local_lb +* @pf: pointer to the pf structure +* +* allow local loopback on pf +*/ +static int +i40e_enable_pf_local_lb (struct rte_eth_dev *dev,int on) +{ +struct i40e_pf *pf =I40E_DEV_PRIVATE_TO_PF (dev->data->dev_private); +struct i40e_hw *hw =I40E_PF_TO_HW (pf); +struct i40e_vsi_context ctxt; +int ret; + +/* Use the FW API if FW >= v5.0 */ +if (hw->aq.fw_maj_ver <5 && hw->mac.type !=I40E_MAC_X722 ) { +#ifdef TREX_PATCH +/* Most of our customers do not have latest FW */ +PMD_INIT_LOG (INFO ,"FW < v5.0, cannot enable local loopback" ); +#else +PMD_INIT_LOG (ERR ,"FW < v5.0, cannot enable local loopback" ); +#endif +return I40E_NOT_SUPPORTED ; + } + +memset (&ctxt,0 ,sizeof (ctxt)); + ctxt.seid = pf->main_vsi_seid; + ctxt.pf_num = hw->pf_id; + ret =i40e_aq_get_vsi_params (hw, &ctxt,NULL ); +if (ret) { +PMD_DRV_LOG (ERR ,"cannot get pf vsi config, err %d, aq_err %d" , + ret, hw->aq.asq_last_status); +return ret; + } + ctxt.flags =I40E_AQ_VSI_TYPE_PF ; + ctxt.info.valid_sections = +rte_cpu_to_le_16 (I40E_AQ_VSI_PROP_SWITCH_VALID ); +if (on) + ctxt.info.switch_id |= +rte_cpu_to_le_16 (I40E_AQ_VSI_SW_ID_FLAG_LOCAL_LB ); +else + ctxt.info.switch_id &= + ~rte_cpu_to_le_16 (I40E_AQ_VSI_SW_ID_FLAG_LOCAL_LB ); + + ret =i40e_aq_update_vsi_params (hw, &ctxt,NULL ); +if (ret) +PMD_DRV_LOG (ERR ,"update vsi switch failed, aq_err=%d" , + hw->aq.asq_last_status); + +return ret; +} +/* Setup a VSI */ struct i40e_vsi * i40e_vsi_setup(struct i40e_pf *pf,lib/ethdev/ethdev_driver.h +0
-0
lib/ethdev/ethdev_driver.h typedef int (*eth_get_module_info_t)(struct rte_eth_dev *dev, · line 674
Quoted 7 lines
lib/ethdev/ethdev_driver.h +4
-0@@ -668,6 +668,10 @@ typedef int (*eth_get_module_info_t)(struct rte_eth_dev *dev,typedef int (*eth_get_module_eeprom_t )(struct rte_eth_dev *dev,struct rte_dev_eeprom_info *info); +/** @internal Function used to enable/disable the vsi loop back of an Ethernet device. */ +typedef int (*eth_enable_local_lb_t )(struct rte_eth_dev *dev, +int on); +
What is 'VSI'? Is it common dpdk or ethdev concept? If not please don't refer it in ethdev.
lib/ethdev/ethdev_driver.h struct eth_dev_ops { · line 1411
Quoted 9 lines
lib/ethdev/ethdev_driver.h +2
-0struct rte_flow_ops ;/** * @internal @@ -1403,6 +1407,8 @@ struct eth_dev_ops {eth_cman_config_set_t cman_config_set;/** Retrieve congestion management configuration */ eth_cman_config_get_t cman_config_get; +/** Enable/disable the vsi loop back of an Ethernet device */ +eth_enable_local_lb_t enable_local_lb;
The name 'enable_local_lb' needs to refined.
Why it is called as 'local_lb'?
And again please use loopback instead of 'lb'.
Quoted 43 lines
lib/ethdev/ethdev_driver.h +0
-0};/** lib/ethdev/rte_ethdev.c +16
-0@@ -6318,6 +6318,22 @@ rte_eth_buffer_split_get_supported_hdr_ptypes(uint16_t port_id, uint32_t *ptypesreturn j; } +int +rte_eth_dev_enable_local_lb (uint16_t port_id,int on) +{ +struct rte_eth_dev *dev; +int ret; + +RTE_ETH_VALID_PORTID_OR_ERR_RET (port_id, -ENODEV ); + dev = &rte_eth_devices[port_id]; + +if (*dev->dev_ops->enable_local_lb ==NULL ) +return -ENOTSUP ; + + ret = (*dev->dev_ops->enable_local_lb)(dev, on); +return eth_err (port_id, ret); +} +RTE_LOG_REGISTER_DEFAULT (rte_eth_dev_logtype,INFO );RTE_INIT (ethdev_init_telemetry)lib/ethdev/rte_ethdev.h +5
-0@@ -3437,6 +3437,21 @@ int rte_eth_dev_set_mtu(uint16_t port_id, uint16_t mtu);*/ int rte_eth_dev_vlan_filter (uint16_t port_id,uint16_t vlan_id,int on); +/** +* Enable/Disable local Loopback for VSIs that are used as uplink of a software +* (cascaded) VEB, VEPA or Port Virtualizer. +* +* @param port_id
lib/ethdev/rte_ethdev.h int rte_eth_dev_set_mtu(uint16_t port_id, uint16_t mtu); · line 3454
Quoted 10 lines
lib/ethdev/rte_ethdev.h +10
-0+* The port identifier of the Ethernet device. +* @param on +* If > 0, enable local Loopback. +* Otherwise, disable local Loopback. +* @return +* - (0) if successful. +* - negative if failed. +*/ +int rte_eth_dev_enable_local_lb (uint16_t port_id,int on); +
API enable/disable the feature but API name has 'enable', so it will be calling enable_X API to disable X,
if API is to enable/disable, perhaps it can be names as 'set_X'?
PATCH v2 1/1 net/i40e: support enabling/disabling source pruning
In reply to Ke ZhangVRRP advertisement packets are dropped on i40e PF devices because when a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a PMD specific API to enable/disable source pruning to fix above issue.
Bugzilla ID: 648
--- app/test-pmd/cmdline.c | 84 +++++++++++++++++++++++++++++++++ drivers/net/i40e/i40e_ethdev.c | 43 +++++++++++++++++ drivers/net/i40e/i40e_ethdev.h | 1 + drivers/net/i40e/rte_pmd_i40e.c | 20 ++++++++ drivers/net/i40e/rte_pmd_i40e.h | 16 +++++++ 5 files changed, 164 insertions(+)
app/test-pmd/cmdline.c +84 -0
@@ -776,6 +776,9 @@ static void cmd_help_long_parsed(void *parsed_result,"port cleanup (port_id) txq (queue_id) (free_cnt)\n" " Cleanup txq mbufs for a specific Tx queue\n\n" + +"port config (port_id|all) src_prune (on|off)\n" +" Set source prune on port_id, or all.\n\n" ); }
@@ -1619,6 +1622,84 @@ static cmdline_parse_inst_t cmd_config_loopback_specific = { }, }; +/* *** configure source prune for port *** */ +struct cmd_config_src_prune_result { +cmdline_fixed_string_t port; +cmdline_fixed_string_t keyword; +cmdline_fixed_string_t port_all;/* valid if "allports" argument == 1 */ +uint16_t port_num;/* valid if "allports" argument == 0 */ +cmdline_fixed_string_t item; +cmdline_fixed_string_t enable; +}; + +static void cmd_config_src_prune_parsed (void *parsed_result, + __rte_unused struct cmdline *cl, +void *allports) +{ +struct cmd_config_src_prune_result *res = parsed_result; +int enable; +portid_t i; + +if (!strcmp (res->enable,"on" )) + enable =1 ; +else + enable =0 ; + +/* all ports */ +if (allports) { +RTE_ETH_FOREACH_DEV (i) +rte_pmd_i40e_set_src_prune (i, enable); + }else { +rte_pmd_i40e_set_src_prune (res->port_num, enable); + } +} + +static cmdline_parse_token_string_t cmd_config_src_prune_port = + TOKEN_STRING_INITIALIZER(struct cmd_config_src_prune_result, port, "port"); +static cmdline_parse_token_string_t cmd_config_src_prune_keyword = + TOKEN_STRING_INITIALIZER(struct cmd_config_src_prune_result, keyword, +"config" ); +static cmdline_parse_token_string_t cmd_config_src_prune_portall = + TOKEN_STRING_INITIALIZER(struct cmd_config_src_prune_result, port_all, +"all" ); +static cmdline_parse_token_num_t cmd_config_src_prune_portnum = + TOKEN_NUM_INITIALIZER(struct cmd_config_src_prune_result, port_num, +RTE_UINT16 ); +static cmdline_parse_token_string_t cmd_config_src_prune_item = + TOKEN_STRING_INITIALIZER(struct cmd_config_src_prune_result, + item,"src_prune" ); +static cmdline_parse_token_string_t cmd_config_src_prune_enable = + TOKEN_STRING_INITIALIZER(struct cmd_config_src_prune_result, enable, +"on#off" ); + +static cmdline_parse_inst_t cmd_config_src_prune_all = { + .f = cmd_config_src_prune_parsed, + .data = (void *)1 , + .help_str ="port config all src_prune (on|off): Set source prune on all ports." , + .tokens = { + (void *)&cmd_config_src_prune_port, + (void *)&cmd_config_src_prune_keyword, + (void *)&cmd_config_src_prune_portall, + (void *)&cmd_config_src_prune_item, + (void *)&cmd_config_src_prune_enable, +NULL , + }, +}; + +static cmdline_parse_inst_t cmd_config_src_prune_specific = { + .f = cmd_config_src_prune_parsed, + .data = (void *)0 , + .help_str ="port config all src_prune (on|off): Set source prune on specific port." , + .tokens = { + (void *)&cmd_config_src_prune_port, + (void *)&cmd_config_src_prune_keyword, + (void *)&cmd_config_src_prune_portnum, + (void *)&cmd_config_src_prune_item, + (void *)&cmd_config_src_prune_enable, +NULL , + }, +}; +/* *** configure txq/rxq, txd/rxd *** */ struct cmd_config_rx_tx {cmdline_fixed_string_t port;
@@ -12731,6 +12812,8 @@ static cmdline_parse_ctx_t builtin_ctx[] = { (cmdline_parse_inst_t *)&cmd_config_speed_specific, (cmdline_parse_inst_t *)&cmd_config_loopback_all, (cmdline_parse_inst_t *)&cmd_config_loopback_specific, + (cmdline_parse_inst_t *)&cmd_config_src_prune_all, + (cmdline_parse_inst_t *)&cmd_config_src_prune_specific, (cmdline_parse_inst_t *)&cmd_config_rx_tx, (cmdline_parse_inst_t *)&cmd_config_mtu, (cmdline_parse_inst_t *)&cmd_config_max_pkt_len,
@@ -12850,6 +12933,7 @@ static cmdline_parse_ctx_t builtin_ctx[] = { (cmdline_parse_inst_t *)&cmd_operate_bpf_unld_parse, #endif (cmdline_parse_inst_t *)&cmd_config_tx_metadata_specific, + (cmdline_parse_inst_t *)&cmd_show_tx_metadata, (cmdline_parse_inst_t *)&cmd_show_rx_tx_desc_status, (cmdline_parse_inst_t *)&cmd_show_rx_queue_desc_used_count,
drivers/net/i40e/i40e_ethdev.c +43 -0
55 lines not on this page · raw message
drivers/net/i40e/i40e_ethdev.h +1 -0
@@ -1427,6 +1427,7 @@ int i40e_pf_calc_configured_queues_num(struct i40e_pf *pf);int i40e_pf_reset_rss_reta (struct i40e_pf *pf);int i40e_pf_reset_rss_key (struct i40e_pf *pf);int i40e_pf_config_rss (struct i40e_pf *pf); +int i40e_set_pf_source_prune (struct i40e_pf *pf,int on);int i40e_set_rss_key (struct i40e_vsi *vsi,uint8_t *key,uint8_t key_len);int i40e_set_rss_lut (struct i40e_vsi *vsi,uint8_t *lut,uint16_t lut_size);int i40e_vf_representor_init (struct rte_eth_dev *ethdev,void *init_params);
drivers/net/i40e/rte_pmd_i40e.c +20 -0
@@ -445,6 +445,26 @@ rte_pmd_i40e_set_tx_loopback(uint16_t port, uint8_t on)return ret; } +int +rte_pmd_i40e_set_src_prune (uint16_t port,uint8_t on) +{ +struct rte_eth_dev *dev; +struct i40e_pf *pf; +int ret; + +RTE_ETH_VALID_PORTID_OR_ERR_RET (port, -ENODEV ); + + dev = &rte_eth_devices[port]; + +if (!is_i40e_supported (dev)) +return -ENOTSUP ; + + pf =I40E_DEV_PRIVATE_TO_PF (dev->data->dev_private); + + ret =i40e_set_pf_source_prune (pf, on); +return ret; +} +int rte_pmd_i40e_set_vf_unicast_promisc (uint16_t port,uint16_t vf_id,uint8_t on) {
drivers/net/i40e/rte_pmd_i40e.h +16 -0
@@ -400,6 +400,22 @@ int rte_pmd_i40e_set_vf_vlan_anti_spoof(uint16_t port,int rte_pmd_i40e_set_tx_loopback (uint16_t port,uint8_t on); +/** +* Enable/Disable source prune on all the PF. +* +* @param port +* The port identifier of the Ethernet device. +* @param on +* 1 - Enable source prune. +* 0 - Disable source prune. +* @return +* - (0) if successful. +* - (-ENODEV) if *port* invalid. +* - (-EINVAL) if bad parameter. +*/ +int rte_pmd_i40e_set_src_prune (uint16_t port, +uint8_t on); +/** * Enable/Disable VF unicast promiscuous mode. *
Signature · 1 line
2.25.1
RE: [PATCH v2] net/i40e: support enabling/disabling source pruning
Quoted 7 lines
From: Ke Zhang [mailto:[email protected]]
Sent: Monday, 30 January 2023 09.09VRRP advertisement packets are dropped on i40e PF devices because when a MAC address is added to a device, packets originating from that MAC address are dropped.
Quoted 7 lines
This patch adds a PMD specific API to enable/disable source pruning to fix above issue.
Bugzilla ID: 648
Signed-off-by Ke Zhang <[email protected]>---
This fixes what I considered a bug in the driver, so source pruning is now disabled by default. Thank you.
Should rte_pmd_i40e_set_src_prune be added to a maps file? (I'm not sure about a PMD specific APIs, so please check.)
Re: [PATCH v2] net/i40e: support enabling/disabling source pruning
In reply to Ke ZhangQuoted 24 lines · Ke Zhang
VRRP advertisement packets are dropped on i40e PF devices because when a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a PMD specific API to enable/disable source pruning to fix above issue.
Bugzilla ID: 648
Signed-off-by Ke Zhang <[email protected]>--- app/test-pmd/cmdline.c | 84 +++++++++++++++++++++++++++++++++ drivers/net/i40e/i40e_ethdev.c | 43 +++++++++++++++++ drivers/net/i40e/i40e_ethdev.h | 1 + drivers/net/i40e/rte_pmd_i40e.c | 20 ++++++++ drivers/net/i40e/rte_pmd_i40e.h | 16 +++++++ 5 files changed, 164 insertions(+)app/test-pmd/cmdline.c +0
-0
app/test-pmd/cmdline.c static void cmd_help_long_parsed(void *parsed_result, · line 784
Quoted 9 lines
app/test-pmd/cmdline.c +3
-0@@ -776,6 +776,9 @@ static void cmd_help_long_parsed(void *parsed_result,"port cleanup (port_id) txq (queue_id) (free_cnt)\n" " Cleanup txq mbufs for a specific Tx queue\n\n" + +"port config (port_id|all) src_prune (on|off)\n" +" Set source prune on port_id, or all.\n\n" ); }
- This seems i40e specific, please move to drivers/net/i40e/i40e_testpmd.c.
- Besides, I would prefer that something in the command name clearly states this is driver (here, i40e) specific.
Like "port config XX i40e_src_prune" or maybe the other way around, start with a "driver i40e" prefix.
Maybe others have an opinion.
Signature · 1 line
David Marchand
RE: [PATCH v2] net/i40e: support enabling/disabling source pruning
Quoted 56 lines
-----Original Message-----
From: David Marchand <[email protected]>
Sent: Monday, January 30, 2023 4:58 PM
To: Zhang, Ke1X <[email protected]>; [email protected]; [email protected]; [email protected]
Cc: [email protected]; Matz, Olivier <[email protected]>; Zhang, Yuying <[email protected]>; Xing, Beilei <[email protected]>
Subject: Re: [PATCH v2] net/i40e: support enabling/disabling source pruningQuoted 2 lines · Ke Zhang
VRRP advertisement packets are dropped on i40e PF devices because
when
Quoted 11 lines
a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a PMD specific API to enable/disable source pruning to fix above issue.
Bugzilla ID: 648
Signed-off-by Ke Zhang <[email protected]>--- app/test-pmd/cmdline.c | 84+++++++++++++++++++++++++++++++++
Quoted 12 lines
drivers/net/i40e/i40e_ethdev.c | 43 +++++++++++++++++ drivers/net/i40e/i40e_ethdev.h | 1 + drivers/net/i40e/rte_pmd_i40e.c | 20 ++++++++ drivers/net/i40e/rte_pmd_i40e.h | 16 +++++++ 5 files changed, 164 insertions(+)app/test-pmd/cmdline.c index renamed from app/test-pmd/cmdline.c +0
-0
cb8c174020..76a574affd100644app/test-pmd/cmdline.c static void cmd_help_long_parsed(void · line 784
Quoted 9 lines
app/test-pmd/cmdline.c +3
-0@@ -776,6 +776,9 @@ static void cmd_help_long_parsed(void *parsed_result,"port cleanup (port_id) txq (queue_id) (free_cnt)\n" " Cleanup txq mbufs for a specific Tx queue\n\n" + +"port config (port_id|all) src_prune (on|off)\n" +" Set source prune on port_id, or all.\n\n" ); }- This seems i40e specific, please move to
drivers/net/i40e/i40e_testpmd.c.- Besides, I would prefer that something in the command name clearly states this is driver (here, i40e) specific.
Like "port config XXi40e_src_prune" or maybe the other way around, start with a "driver i40e" prefix.
Quoted 5 lines
Maybe others have an opinion.
--
David Marchand
Thanks for your comments, this command could be used for other Intel NIC like ice, And It is only finished for i40e in this story: https://jira.devtools.intel.com/browse/DPDK-29564
Re: [PATCH v2] net/i40e: support enabling/disabling source pruning
31/01/2023 04:28, Zhang, Ke1X:
Quoted 46 lines
From: David Marchand <[email protected]>
Quoted 45 lines · Ke Zhang
Quoted 2 lines
VRRP advertisement packets are dropped on i40e PF devices because
when
Quoted 11 lines
a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a PMD specific API to enable/disable source pruning to fix above issue.
Bugzilla ID: 648
Signed-off-by Ke Zhang <[email protected]>--- app/test-pmd/cmdline.c | 84+++++++++++++++++++++++++++++++++
Quoted 12 lines
drivers/net/i40e/i40e_ethdev.c | 43 +++++++++++++++++ drivers/net/i40e/i40e_ethdev.h | 1 + drivers/net/i40e/rte_pmd_i40e.c | 20 ++++++++ drivers/net/i40e/rte_pmd_i40e.h | 16 +++++++ 5 files changed, 164 insertions(+)app/test-pmd/cmdline.c index renamed from app/test-pmd/cmdline.c +0
-0
cb8c174020..76a574affd100644app/test-pmd/cmdline.c static void cmd_help_long_parsed(void · line 784
Quoted 9 lines
app/test-pmd/cmdline.c +3
-0@@ -776,6 +776,9 @@ static void cmd_help_long_parsed(void *parsed_result,"port cleanup (port_id) txq (queue_id) (free_cnt)\n" " Cleanup txq mbufs for a specific Tx queue\n\n" + +"port config (port_id|all) src_prune (on|off)\n" +" Set source prune on port_id, or all.\n\n" ); }- This seems i40e specific, please move to
drivers/net/i40e/i40e_testpmd.c.- Besides, I would prefer that something in the command name clearly states this is driver (here, i40e) specific.
Like "port config XXi40e_src_prune" or maybe the other way around, start with a "driver i40e" prefix.
Quoted 8 lines
Quoted 5 lines
Maybe others have an opinion.
--
David MarchandThanks for your comments, this command could be used for other Intel NIC like ice, And It is only finished for i40e in this story: https://jira.devtools.intel.com/browse/DPDK-29564
Only Intel has access to this URL.
On the principle, you should not update testpmd commands in a patch for i40e. We add testpmd commands when adding new features in ethdev.
Here specifically, you are adding rte_pmd_i40e_set_src_prune() with a vague explanation: "Enable/Disable source prune on all the PF." Without more information, I cannot judge whether the feature is generic or not. So for now, this is a nack.
RE: [PATCH v2] net/i40e: support enabling/disabling source pruning
Quoted 77 lines
-----Original Message-----
From: Thomas Monjalon <[email protected]>
Sent: Wednesday, February 1, 2023 7:11 PM
To: David Marchand <[email protected]>; [email protected]; [email protected]; Zhang, Ke1X <[email protected]>
Cc: [email protected]; Matz, Olivier <[email protected]>; Zhang, Yuying <[email protected]>; Xing, Beilei <[email protected]>
Subject: Re: [PATCH v2] net/i40e: support enabling/disabling source pruning31/01/2023 04:28, Zhang, Ke1X:
Quoted 2 lines
From: David Marchand <[email protected]>
Quoted 1 line
On Mon, Jan 30, 2023 at 9:23 AM Ke Zhang <[email protected]>
Quoted 28 lines · wrote:
Quoted 28 lines
Quoted 2 lines
VRRP advertisement packets are dropped on i40e PF devices because
when
Quoted 11 lines
a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a PMD specific API to enable/disable source pruning to fix above issue.
Bugzilla ID: 648
Signed-off-by Ke Zhang <[email protected]>--- app/test-pmd/cmdline.c | 84+++++++++++++++++++++++++++++++++
Quoted 13 lines
drivers/net/i40e/i40e_ethdev.c | 43 +++++++++++++++++ drivers/net/i40e/i40e_ethdev.h | 1 + drivers/net/i40e/rte_pmd_i40e.c | 20 ++++++++ drivers/net/i40e/rte_pmd_i40e.h | 16 +++++++ 5 files changed, 164 insertions(+)app/test-pmd/cmdline.c index renamed from app/test-pmd/cmdline.c +0
-0
cb8c174020..76a574affd100644app/test-pmd/cmdline.c +0
-0@@ -776,6 +776,9 @@ static void cmd_help_long_parsed(void *parsed_result,Quoted 10 lines
Quoted 10 lines
app/test-pmd/cmdline.c static void cmd_help_long_parsed(void *parsed_result, · line 783
Quoted 8 lines
app/test-pmd/cmdline.c +3
-0"port cleanup (port_id) txq (queue_id) (free_cnt)\n" " Cleanup txq mbufs for a specific Tx queue\n\n" + +"port config (port_id|all) src_prune (on|off)\n" +" Set source prune on port_id, or all.\n\n" ); }- This seems i40e specific, please move to
drivers/net/i40e/i40e_testpmd.c.Quoted 9 lines
Quoted 9 lines
- Besides, I would prefer that something in the command name clearly states this is driver (here, i40e) specific.
Like "port config XXi40e_src_prune" or maybe the other way around, start with a "driver i40e" prefix.Maybe others have an opinion.
Quoted 6 lines
Quoted 2 lines
--
David MarchandThanks for your comments, this command could be used for other Intel NIC like ice, And It is only finished for i40e in this story:
https://jira.devtools.intel.com/browse/DPDK-29564Only Intel has access to this URL.
On the principle, you should not update testpmd commands in a patch for i40e.
We add testpmd commands when adding new features in ethdev.
Quoted 6 lines
Here specifically, you are adding
rte_pmd_i40e_set_src_prune()with a vague explanation: "Enable/Disable source prune on all the PF." Without more information, I cannot judge whether the feature is generic or not.
So for now, this is a nack.
Thanks for your comments, this feature is only for intel NIC. Would you please share a solution for this case? Thanks.
Re: [PATCH v2] net/i40e: support enabling/disabling source pruning
07/02/2023 02:40, Zhang, Ke1X:
Quoted 66 lines
From: Thomas Monjalon <[email protected]>
Quoted 65 lines
31/01/2023 04:28, Zhang, Ke1X:
Quoted 2 lines
From: David Marchand <[email protected]>
Quoted 1 line
On Mon, Jan 30, 2023 at 9:23 AM Ke Zhang <[email protected]>
Quoted 28 lines · wrote:
Quoted 28 lines
Quoted 2 lines
VRRP advertisement packets are dropped on i40e PF devices because
when
Quoted 11 lines
a MAC address is added to a device, packets originating from that MAC address are dropped.
This patch adds a PMD specific API to enable/disable source pruning to fix above issue.
Bugzilla ID: 648
Signed-off-by Ke Zhang <[email protected]>--- app/test-pmd/cmdline.c | 84+++++++++++++++++++++++++++++++++
Quoted 13 lines
drivers/net/i40e/i40e_ethdev.c | 43 +++++++++++++++++ drivers/net/i40e/i40e_ethdev.h | 1 + drivers/net/i40e/rte_pmd_i40e.c | 20 ++++++++ drivers/net/i40e/rte_pmd_i40e.h | 16 +++++++ 5 files changed, 164 insertions(+)app/test-pmd/cmdline.c index renamed from app/test-pmd/cmdline.c +0
-0
cb8c174020..76a574affd100644app/test-pmd/cmdline.c +0
-0@@ -776,6 +776,9 @@ static void cmd_help_long_parsed(void *parsed_result,Quoted 10 lines
Quoted 10 lines
app/test-pmd/cmdline.c static void cmd_help_long_parsed(void *parsed_result, · line 783
Quoted 8 lines
app/test-pmd/cmdline.c +3
-0"port cleanup (port_id) txq (queue_id) (free_cnt)\n" " Cleanup txq mbufs for a specific Tx queue\n\n" + +"port config (port_id|all) src_prune (on|off)\n" +" Set source prune on port_id, or all.\n\n" ); }- This seems i40e specific, please move to
drivers/net/i40e/i40e_testpmd.c.Quoted 9 lines
Quoted 9 lines
- Besides, I would prefer that something in the command name clearly states this is driver (here, i40e) specific.
Like "port config XXi40e_src_prune" or maybe the other way around, start with a "driver i40e" prefix.Maybe others have an opinion.
Quoted 6 lines
Quoted 2 lines
--
David MarchandThanks for your comments, this command could be used for other Intel NIC like ice, And It is only finished for i40e in this story:
https://jira.devtools.intel.com/browse/DPDK-29564Only Intel has access to this URL.
On the principle, you should not update testpmd commands in a patch for i40e.
We add testpmd commands when adding new features in ethdev.
Quoted 8 lines
Quoted 6 lines
Here specifically, you are adding
rte_pmd_i40e_set_src_prune()with a vague explanation: "Enable/Disable source prune on all the PF." Without more information, I cannot judge whether the feature is generic or not.
So for now, this is a nack.Thanks for your comments, this feature is only for intel NIC. Would you please share a solution for this case?
Host testpmd code in your driver directory
with a command name starting with the name of your driver: "i40e port ...". You can look at what is done for mlx5 in drivers/net/mlx5/mlx5_testpmd.c