mmc: vub300: fix control-message timeouts

USB control-message timeouts are specified in milliseconds and should specifically not vary with CONFIG_HZ.

Fixes 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")

Cc [email protected] # 3.0

Signed-off-by Johan Hovold <[email protected]>

---
 drivers/mmc/host/vub300.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

drivers/mmc/host/vub300.c +9 -10

index 4950d10d3a19..97beece62fec 100644
@@ -576,7 +576,7 @@ static void check_vub300_port_status(struct vub300_mmc_host *vub300)
                                GET_SYSTEM_PORT_STATUS,
                                USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
                                0x0000, 0x0000, &vub300->system_port_status,
-                               sizeof(vub300->system_port_status), HZ);
+                               sizeof(vub300->system_port_status), 1000);
        if (sizeof(vub300->system_port_status) == retval)
                new_system_port_status(vub300);
 }

@@ -1241,7 +1241,7 @@ static void __download_offload_pseudocode(struct vub300_mmc_host *vub300,
                                                SET_INTERRUPT_PSEUDOCODE,
                                                USB_DIR_OUT | USB_TYPE_VENDOR |
                                                USB_RECIP_DEVICE, 0x0000, 0x0000,
-                                               xfer_buffer, xfer_length, HZ);
+                                               xfer_buffer, xfer_length, 1000);
                        kfree(xfer_buffer);
                        if (retval < 0)
                                goto copy_error_message;

@@ -1284,7 +1284,7 @@ static void __download_offload_pseudocode(struct vub300_mmc_host *vub300,
                                                SET_TRANSFER_PSEUDOCODE,
                                                USB_DIR_OUT | USB_TYPE_VENDOR |
                                                USB_RECIP_DEVICE, 0x0000, 0x0000,
-                                               xfer_buffer, xfer_length, HZ);
+                                               xfer_buffer, xfer_length, 1000);
                        kfree(xfer_buffer);
                        if (retval < 0)
                                goto copy_error_message;

@@ -1991,7 +1991,7 @@ static void __set_clock_speed(struct vub300_mmc_host *vub300, u8 buf[8],
                usb_control_msg(vub300->udev, usb_sndctrlpipe(vub300->udev, 0),
                                SET_CLOCK_SPEED,
                                USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-                               0x00, 0x00, buf, buf_array_size, HZ);
+                               0x00, 0x00, buf, buf_array_size, 1000);
        if (retval != 8) {
                dev_err(&vub300->udev->dev, "SET_CLOCK_SPEED"
                        " %dkHz failed with retval=%d\n", kHzClock, retval);

@@ -2013,14 +2013,14 @@ static void vub300_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
                usb_control_msg(vub300->udev, usb_sndctrlpipe(vub300->udev, 0),
                                SET_SD_POWER,
                                USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-                               0x0000, 0x0000, NULL, 0, HZ);
+                               0x0000, 0x0000, NULL, 0, 1000);
                /* must wait for the VUB300 u-proc to boot up */
                msleep(600);
        } else if ((ios->power_mode == MMC_POWER_UP) && !vub300->card_powered) {
                usb_control_msg(vub300->udev, usb_sndctrlpipe(vub300->udev, 0),
                                SET_SD_POWER,
                                USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-                               0x0001, 0x0000, NULL, 0, HZ);
+                               0x0001, 0x0000, NULL, 0, 1000);
                msleep(600);
                vub300->card_powered = 1;
        } else if (ios->power_mode == MMC_POWER_ON) {

@@ -2275,14 +2275,14 @@ static int vub300_probe(struct usb_interface *interface,
                                GET_HC_INF0,
                                USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
                                0x0000, 0x0000, &vub300->hc_info,
-                               sizeof(vub300->hc_info), HZ);
+                               sizeof(vub300->hc_info), 1000);
        if (retval < 0)
                goto error5;
        retval =
                usb_control_msg(vub300->udev, usb_sndctrlpipe(vub300->udev, 0),
                                SET_ROM_WAIT_STATES,
                                USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-                               firmware_rom_wait_states, 0x0000, NULL, 0, HZ);
+                               firmware_rom_wait_states, 0x0000, NULL, 0, 1000);
        if (retval < 0)
                goto error5;
        dev_info(&vub300->udev->dev,

@@ -2297,7 +2297,7 @@ static int vub300_probe(struct usb_interface *interface,
                                GET_SYSTEM_PORT_STATUS,
                                USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
                                0x0000, 0x0000, &vub300->system_port_status,
-                               sizeof(vub300->system_port_status), HZ);
+                               sizeof(vub300->system_port_status), 1000);
        if (retval < 0) {
                goto error4;
        } else if (sizeof(vub300->system_port_status) == retval) {
--

2.32.0