Skip to contentSkip to conversation

Extensions to ov8865 driver

PATCH Superseded Daniel Scally 4 participants 32 messages Nov 1, 2021 – Nov 22, 2021

Subsystems (3)

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v4 cover Extensions to ov8865 driver

Hello all

This series extends the ov8865 driver with:

* Support for binding to ACPI enumerated devices.
* Support for a 19.2MHz clock in addition to existing 24MHz clock support
* Another v4l2_subdev_pad_ops callback
* 4 more V4L2 controls
* makes the driver supported by the cio2-bridge

There's also a little bit of tidying that I did along the way.

The series is tested on an MS Surface Go 2.

Thanks
Dan

Series changes since V3:

- Fixed a problem that prevented v3 applying properly due to the series being based on my WIP tree rather than a clean media tree. No code changes to the individual patches.

Daniel Scally (15):
media: i2c: Add ACPI support to ov8865
media: i2c: Fix incorrect value in comment
media: i2c: Defer probe if not endpoint found
media: i2c: Support 19.2MHz input clock in ov8865
media: i2c: Add .get_selection() support to ov8865
media: i2c: Switch control to V4L2_CID_ANALOGUE_GAIN
media: i2c: Add vblank control to ov8865
media: i2c: Add hblank control to ov8865
media: i2c: Update HTS values in ov8865
media: i2c: cap exposure at height + vblank in ov8865
media: i2c: Add controls from fwnode to ov8865
media: i2c: Switch exposure control unit to lines
media: i2c: Re-order runtime pm initialisation
media: i2c: Use dev_err_probe() in ov8865
media: ipu3-cio2: Add INT347A to cio2-bridge

Hans de Goede (1):
media: i2c: ov8865: Fix lockdep error

 drivers/media/i2c/ov8865.c                 | 459 +++++++++++++++------
 drivers/media/pci/intel/ipu3/cio2-bridge.c |   2 +
 2 files changed, 327 insertions(+), 134 deletions(-)
Signature · 1 line
2.25.1
#1 lore raw

PATCH v4 1/16 media: i2c: Add ACPI support to ov8865

The ov8865 sensor is sometimes found on x86 platforms enumerated via ACPI. Add an ACPI match table to the driver so that it's probed on those platforms.

---
 drivers/media/i2c/ov8865.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/media/i2c/ov8865.c +8 -0
index ce50f3ea87b8..7626c8608f8f 100644
@@ -9,6 +9,7 @@
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/i2c.h>
+#include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/of_graph.h>
 #include <linux/pm_runtime.h>
@@ -2946,6 +2947,12 @@ static const struct dev_pm_ops ov8865_pm_ops = {
 	SET_RUNTIME_PM_OPS(ov8865_suspend, ov8865_resume, NULL)
 };
 
+static const struct acpi_device_id ov8865_acpi_match[] = {
+	{"INT347A"},
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, ov8865_acpi_match);
+
 static const struct of_device_id ov8865_of_match[] = {
 	{ .compatible = "ovti,ov8865" },
 	{ }
@@ -2956,6 +2963,7 @@ static struct i2c_driver ov8865_driver = {
 	.driver = {
 		.name = "ov8865",
 		.of_match_table = ov8865_of_match,
+		.acpi_match_table = ov8865_acpi_match,
 		.pm = &ov8865_pm_ops,
 	},
 	.probe_new = ov8865_probe,
Signature · 1 line
2.25.1
#2 lore raw

Re: [PATCH v4 01/16] media: i2c: Add ACPI support to ov8865

Quoted 15 lines · Daniel Scally

The ov8865 sensor is sometimes found on x86 platforms enumerated via ACPI. Add an ACPI match table to the driver so that it's probed on those platforms.

---
 drivers/media/i2c/ov8865.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/media/i2c/ov8865.c +0 -0
index ce50f3ea87b8..7626c8608f8f 100644

drivers/media/i2c/ov8865.c line 15

Quoted 7 lines
drivers/media/i2c/ov8865.c +1 -0
@@ -9,6 +9,7 @@
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/i2c.h>
+#include <linux/mod_devicetable.h>
 #include <linux/module.h>
 
 #include <linux/of_graph.h>

I'm wondering if the code even uses of_*() APIs.
If nbo, maybe it's good to replace of_graph.h with property.h.

Quoted 25 lines

#include <linux/pm_runtime.h>

drivers/media/i2c/ov8865.c +7 -1
@@ -2946,6 +2947,12 @@ static const struct dev_pm_ops ov8865_pm_ops = {
        SET_RUNTIME_PM_OPS(ov8865_suspend, ov8865_resume, NULL)
 };
 
+static const struct acpi_device_id ov8865_acpi_match[] = {
+       {"INT347A"},
+       { }
+};
+MODULE_DEVICE_TABLE(acpi, ov8865_acpi_match);
+
 static const struct of_device_id ov8865_of_match[] = {
        { .compatible = "ovti,ov8865" },
        { }
@@ -2956,6 +2963,7 @@ static struct i2c_driver ov8865_driver = {
        .driver = {
                .name = "ov8865",
                .of_match_table = ov8865_of_match,
+               .acpi_match_table = ov8865_acpi_match,
                .pm = &ov8865_pm_ops,
        },
        .probe_new = ov8865_probe,
--

2.25.1

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#3 lore raw

Re: [PATCH v4 01/16] media: i2c: Add ACPI support to ov8865

Quoted 10 lines · Andy Shevchenko
Quoted 9 lines · Daniel Scally

The ov8865 sensor is sometimes found on x86 platforms enumerated via ACPI. Add an ACPI match table to the driver so that it's probed on those platforms.

---
 drivers/media/i2c/ov8865.c | 8 ++++++++
 1 file changed, 8 insertions(+)
Quoted 13 lines

drivers/media/i2c/ov8865.c line 14

Quoted 11 lines
drivers/media/i2c/ov8865.c +1 -0
index ce50f3ea87b8..7626c8608f8f 100644
@@ -9,6 +9,7 @@
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/i2c.h>
+#include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/of_graph.h>

I'm wondering if the code even uses of_*() APIs.
If nbo, maybe it's good to replace of_graph.h with property.h.

Yeah you're right; it doesn't use any of_*() calls. I'll add a patch

Quoted 26 lines
Quoted 25 lines
drivers/media/i2c/ov8865.c +7 -1
 #include <linux/pm_runtime.h>
@@ -2946,6 +2947,12 @@ static const struct dev_pm_ops ov8865_pm_ops = {
        SET_RUNTIME_PM_OPS(ov8865_suspend, ov8865_resume, NULL)
 };
 
+static const struct acpi_device_id ov8865_acpi_match[] = {
+       {"INT347A"},
+       { }
+};
+MODULE_DEVICE_TABLE(acpi, ov8865_acpi_match);
+
 static const struct of_device_id ov8865_of_match[] = {
        { .compatible = "ovti,ov8865" },
        { }
@@ -2956,6 +2963,7 @@ static struct i2c_driver ov8865_driver = {
        .driver = {
                .name = "ov8865",
                .of_match_table = ov8865_of_match,
+               .acpi_match_table = ov8865_acpi_match,
                .pm = &ov8865_pm_ops,
        },
        .probe_new = ov8865_probe,
--

2.25.1

#4 lore raw

PATCH v4 2/16 media: i2c: Fix incorrect value in comment

In reply to Daniel Scally

The PLL configuration defined here sets 72MHz (which is correct), not 80MHz. Correct the comment.

---
 drivers/media/i2c/ov8865.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/media/i2c/ov8865.c +1 -1
index 7626c8608f8f..8e3f8a554452 100644
@@ -713,7 +713,7 @@ static const struct ov8865_pll2_config ov8865_pll2_config_native = {
 /*
  * EXTCLK = 24 MHz
  * DAC_CLK = 360 MHz
- * SCLK = 80 MHz
+ * SCLK = 72 MHz
  */
 
 static const struct ov8865_pll2_config ov8865_pll2_config_binning = {
Signature · 1 line
2.25.1
#5 lore raw

PATCH v4 3/16 media: i2c: Defer probe if not endpoint found

In reply to Daniel Scally

The ov8865 driver is one of those that can be connected to a CIO2 device by the cio2-bridge code. This means that the absence of an endpoint for this device is not necessarily fatal, as one might be built by the cio2-bridge when it probes. Return -EPROBE_DEFER if no endpoint is found rather than a fatal error.

---
 drivers/media/i2c/ov8865.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/media/i2c/ov8865.c +2 -4
index 8e3f8a554452..9bc8d5d8199b 100644
@@ -2796,10 +2796,8 @@ static int ov8865_probe(struct i2c_client *client)
 	/* Graph Endpoint */
 
 	handle = fwnode_graph_get_next_endpoint(dev_fwnode(dev), NULL);
-	if (!handle) {
-		dev_err(dev, "unable to find endpoint node\n");
-		return -EINVAL;
-	}
+	if (!handle)
+		return -EPROBE_DEFER;
 
 	sensor->endpoint.bus_type = V4L2_MBUS_CSI2_DPHY;
 
Signature · 1 line
2.25.1
#6 lore raw

PATCH v4 4/16 media: i2c: Support 19.2MHz input clock in ov8865

In reply to Daniel Scally

The ov8865 driver as written expects a 24MHz input clock, but the sensor is sometimes found on x86 platforms with a 19.2MHz input clock supplied. Add a set of PLL configurations to the driver to support that rate too. As ACPI doesn't auto-configure the clock rate, check for a clock-frequency during probe and set that rate if one is found.

---
 drivers/media/i2c/ov8865.c | 186 +++++++++++++++++++++++++++----------
 1 file changed, 135 insertions(+), 51 deletions(-)
drivers/media/i2c/ov8865.c +135 -51
index 9bc8d5d8199b..4ddc1b277cc0 100644
@@ -21,10 +21,6 @@
 #include <media/v4l2-image-sizes.h>
 #include <media/v4l2-mediabus.h>
 
-/* Clock rate */
-
-#define OV8865_EXTCLK_RATE			24000000
-
 /* Register definitions */
 
 /* System */
@@ -567,6 +563,25 @@ struct ov8865_sclk_config {
 	unsigned int sclk_div;
 };
 
+struct ov8865_pll_configs {
+	const struct ov8865_pll1_config *pll1_config;
+	const struct ov8865_pll2_config *pll2_config_native;
+	const struct ov8865_pll2_config *pll2_config_binning;
+};
+
+/* Clock rate */
+
+enum extclk_rate {
+	OV8865_19_2_MHZ,
+	OV8865_24_MHZ,
+	OV8865_NUM_SUPPORTED_RATES
+};
+
+static const unsigned long supported_extclk_rates[] = {
+	[OV8865_19_2_MHZ] = 19200000,
+	[OV8865_24_MHZ] = 24000000,
+};
+
 /*
  * General formulas for (array-centered) mode calculation:
  * - photo_array_width = 3296
@@ -635,9 +650,7 @@ struct ov8865_mode {
 
 	struct v4l2_fract frame_interval;
 
-	const struct ov8865_pll1_config *pll1_config;
-	const struct ov8865_pll2_config *pll2_config;
-	const struct ov8865_sclk_config *sclk_config;
+	bool pll2_binning;
 
 	const struct ov8865_register_value *register_values;
 	unsigned int register_values_count;
@@ -665,6 +678,9 @@ struct ov8865_sensor {
 	struct regulator *avdd;
 	struct regulator *dvdd;
 	struct regulator *dovdd;
+
+	unsigned long extclk_rate;
+	const struct ov8865_pll_configs *pll_configs;
 	struct clk *extclk;
 
 	struct v4l2_fwnode_endpoint endpoint;
@@ -680,43 +696,70 @@ struct ov8865_sensor {
 /* Static definitions */
 
 /*
- * EXTCLK = 24 MHz
  * PHY_SCLK = 720 MHz
  * MIPI_PCLK = 90 MHz
  */
-static const struct ov8865_pll1_config ov8865_pll1_config_native = {
-	.pll_pre_div_half	= 1,
-	.pll_pre_div		= 0,
-	.pll_mul		= 30,
-	.m_div			= 1,
-	.mipi_div		= 3,
-	.pclk_div		= 1,
-	.sys_pre_div		= 1,
-	.sys_div		= 2,
+
+static const struct ov8865_pll1_config ov8865_pll1_config_native_19_2mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 2,
+		.pll_mul		= 75,
+		.m_div			= 1,
+		.mipi_div		= 3,
+		.pclk_div		= 1,
+		.sys_pre_div		= 1,
+		.sys_div		= 2,
+};
+
+static const struct ov8865_pll1_config ov8865_pll1_config_native_24mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 0,
+		.pll_mul		= 30,
+		.m_div			= 1,
+		.mipi_div		= 3,
+		.pclk_div		= 1,
+		.sys_pre_div		= 1,
+		.sys_div		= 2,
 };
 
 /*
- * EXTCLK = 24 MHz
  * DAC_CLK = 360 MHz
  * SCLK = 144 MHz
  */
 
-static const struct ov8865_pll2_config ov8865_pll2_config_native = {
-	.pll_pre_div_half	= 1,
-	.pll_pre_div		= 0,
-	.pll_mul		= 30,
-	.dac_div		= 2,
-	.sys_pre_div		= 5,
-	.sys_div		= 0,
+static const struct ov8865_pll2_config ov8865_pll2_config_native_19_2mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 5,
+		.pll_mul		= 75,
+		.dac_div		= 1,
+		.sys_pre_div		= 1,
+		.sys_div		= 3,
+};
+
+static const struct ov8865_pll2_config ov8865_pll2_config_native_24mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 0,
+		.pll_mul		= 30,
+		.dac_div		= 2,
+		.sys_pre_div		= 5,
+		.sys_div		= 0,
 };
 
 /*
- * EXTCLK = 24 MHz
  * DAC_CLK = 360 MHz
  * SCLK = 72 MHz
  */
 
-static const struct ov8865_pll2_config ov8865_pll2_config_binning = {
+static const struct ov8865_pll2_config ov8865_pll2_config_binning_19_2mhz = {
+	.pll_pre_div_half	= 1,
+	.pll_pre_div		= 2,
+	.pll_mul		= 75,
+	.dac_div		= 2,
+	.sys_pre_div		= 10,
+	.sys_div		= 0,
+};
+
+static const struct ov8865_pll2_config ov8865_pll2_config_binning_24mhz = {
 	.pll_pre_div_half	= 1,
 	.pll_pre_div		= 0,
 	.pll_mul		= 30,
@@ -725,6 +768,23 @@ static const struct ov8865_pll2_config ov8865_pll2_config_binning = {
 	.sys_div		= 0,
 };
 
+static struct ov8865_pll_configs ov8865_pll_configs_19_2mhz = {
+	.pll1_config = &ov8865_pll1_config_native_19_2mhz,
+	.pll2_config_native = &ov8865_pll2_config_native_19_2mhz,
+	.pll2_config_binning = &ov8865_pll2_config_binning_19_2mhz,
+};
+
+static struct ov8865_pll_configs ov8865_pll_configs_24mhz = {
+	.pll1_config = &ov8865_pll1_config_native_24mhz,
+	.pll2_config_native = &ov8865_pll2_config_native_24mhz,
+	.pll2_config_binning = &ov8865_pll2_config_binning_24mhz,
+};
+
+static const struct ov8865_pll_configs *ov8865_pll_configs[] = {
+	&ov8865_pll_configs_19_2mhz,
+	&ov8865_pll_configs_24mhz,
+};
+
 static const struct ov8865_sclk_config ov8865_sclk_config_native = {
 	.sys_sel		= 1,
 	.sclk_sel		= 0,
@@ -934,9 +994,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 30 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_native,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= false,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_native,
@@ -990,9 +1048,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 30 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_native,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= false,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_native,
@@ -1050,9 +1106,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 30 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_binning,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= true,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_binning,
@@ -1116,9 +1170,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 90 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_binning,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= true,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_binning,
@@ -1513,12 +1565,11 @@ static int ov8865_isp_configure(struct ov8865_sensor *sensor)
 static unsigned long ov8865_mode_pll1_rate(struct ov8865_sensor *sensor,
 					   const struct ov8865_mode *mode)
 {
-	const struct ov8865_pll1_config *config = mode->pll1_config;
-	unsigned long extclk_rate;
+	const struct ov8865_pll1_config *config;
 	unsigned long pll1_rate;
 
-	extclk_rate = clk_get_rate(sensor->extclk);
-	pll1_rate = extclk_rate * config->pll_mul / config->pll_pre_div_half;
+	config = sensor->pll_configs->pll1_config;
+	pll1_rate = sensor->extclk_rate * config->pll_mul / config->pll_pre_div_half;
 
 	switch (config->pll_pre_div) {
 	case 0:
@@ -1552,10 +1603,12 @@ static int ov8865_mode_pll1_configure(struct ov8865_sensor *sensor,
 				      const struct ov8865_mode *mode,
 				      u32 mbus_code)
 {
-	const struct ov8865_pll1_config *config = mode->pll1_config;
+	const struct ov8865_pll1_config *config;
 	u8 value;
 	int ret;
 
+	config = sensor->pll_configs->pll1_config;
+
 	switch (mbus_code) {
 	case MEDIA_BUS_FMT_SBGGR10_1X10:
 		value = OV8865_MIPI_BIT_SEL(10);
@@ -1622,9 +1675,12 @@ static int ov8865_mode_pll1_configure(struct ov8865_sensor *sensor,
 static int ov8865_mode_pll2_configure(struct ov8865_sensor *sensor,
 				      const struct ov8865_mode *mode)
 {
-	const struct ov8865_pll2_config *config = mode->pll2_config;
+	const struct ov8865_pll2_config *config;
 	int ret;
 
+	config = mode->pll2_binning ? sensor->pll_configs->pll2_config_binning :
+				      sensor->pll_configs->pll2_config_native;
+
 	ret = ov8865_write(sensor, OV8865_PLL_CTRL12_REG,
 			   OV8865_PLL_CTRL12_PRE_DIV_HALF(config->pll_pre_div_half) |
 			   OV8865_PLL_CTRL12_DAC_DIV(config->dac_div));
@@ -1658,7 +1714,7 @@ static int ov8865_mode_pll2_configure(struct ov8865_sensor *sensor,
 static int ov8865_mode_sclk_configure(struct ov8865_sensor *sensor,
 				      const struct ov8865_mode *mode)
 {
-	const struct ov8865_sclk_config *config = mode->sclk_config;
+	const struct ov8865_sclk_config *config = &ov8865_sclk_config_native;
 	int ret;
 
 	ret = ov8865_write(sensor, OV8865_CLK_SEL0_REG,
@@ -2053,9 +2109,11 @@ static int ov8865_mode_configure(struct ov8865_sensor *sensor,
 static unsigned long ov8865_mode_mipi_clk_rate(struct ov8865_sensor *sensor,
 					       const struct ov8865_mode *mode)
 {
-	const struct ov8865_pll1_config *config = mode->pll1_config;
+	const struct ov8865_pll1_config *config;
 	unsigned long pll1_rate;
 
+	config = sensor->pll_configs->pll1_config;
+
 	pll1_rate = ov8865_mode_pll1_rate(sensor, mode);
 
 	return pll1_rate / config->m_div / 2;
@@ -2783,7 +2841,8 @@ static int ov8865_probe(struct i2c_client *client)
 	struct ov8865_sensor *sensor;
 	struct v4l2_subdev *subdev;
 	struct media_pad *pad;
-	unsigned long rate;
+	unsigned int rate;
+	unsigned int i;
 	int ret;
 
 	sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
@@ -2858,13 +2917,38 @@ static int ov8865_probe(struct i2c_client *client)
 		goto error_endpoint;
 	}
 
-	rate = clk_get_rate(sensor->extclk);
-	if (rate != OV8865_EXTCLK_RATE) {
-		dev_err(dev, "clock rate %lu Hz is unsupported\n", rate);
+	/*
+	 * We could have either a 24MHz or 19.2MHz clock rate. Check for a
+	 * clock-frequency property and if found, set that rate. This should
+	 * cover the ACPI case. If the system uses devicetree then the
+	 * configured rate should already be set, so we'll have to check it.
+	 */
+	ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
+				       &rate);
+	if (!ret) {
+		ret = clk_set_rate(sensor->extclk, rate);
+		if (ret) {
+			dev_err(dev, "failed to set clock rate\n");
+			return ret;
+		}
+	}
+
+	sensor->extclk_rate = clk_get_rate(sensor->extclk);
+
+	for (i = 0; i < ARRAY_SIZE(supported_extclk_rates); i++) {
+		if (sensor->extclk_rate == supported_extclk_rates[i])
+			break;
+	}
+
+	if (i == ARRAY_SIZE(supported_extclk_rates)) {
+		dev_err(dev, "clock rate %lu Hz is unsupported\n",
+			sensor->extclk_rate);
 		ret = -EINVAL;
 		goto error_endpoint;
 	}
 
+	sensor->pll_configs = ov8865_pll_configs[i];
+
 	/* Subdev, entity and pad */
 
 	subdev = &sensor->subdev;
Signature · 1 line
2.25.1
#7 lore raw

Re: [PATCH v4 04/16] media: i2c: Support 19.2MHz input clock in ov8865

Quoted 6 lines · Daniel Scally

The ov8865 driver as written expects a 24MHz input clock, but the sensor is sometimes found on x86 platforms with a 19.2MHz input clock supplied. Add a set of PLL configurations to the driver to support that rate too. As ACPI doesn't auto-configure the clock rate, check for a clock-frequency during probe and set that rate if one is found.

...

Quoted 5 lines
drivers/media/i2c/ov8865.c +5 -0
+       /*
+        * We could have either a 24MHz or 19.2MHz clock rate. Check for a
+        * clock-frequency property and if found, set that rate. This should
+        * cover the ACPI case. If the system uses devicetree then the
+        * configured rate should already be set, so we'll have to check it.

drivers/media/i2c/ov8865.c static int ov8865_probe(struct i2c_client *client)

Quoted 10 lines
drivers/media/i2c/ov8865.c +9 -0
+        */
+       ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
+                                      &rate);
+       if (!ret) {
+               ret = clk_set_rate(sensor->extclk, rate);
 
+               if (ret) {
+                       dev_err(dev, "failed to set clock rate\n");
+                       return ret;
+               }

dev_err_probe()
7065f92255bb ("driver core: Clarify that dev_err_probe() is OK even w/out -EPROBE_DEFER")

Quoted 1 line

+ }

...

drivers/media/i2c/ov8865.c static int ov8865_probe(struct i2c_client *client) · line 2948

Quoted 11 lines
drivers/media/i2c/ov8865.c +8 -0
+       for (i = 0; i < ARRAY_SIZE(supported_extclk_rates); i++) {
+               if (sensor->extclk_rate == supported_extclk_rates[i])
+                       break;
+       }
+
+       if (i == ARRAY_SIZE(supported_extclk_rates)) {
+               dev_err(dev, "clock rate %lu Hz is unsupported\n",
+                       sensor->extclk_rate);
                ret = -EINVAL;
                goto error_endpoint;
        }

find_closest() ?

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#8 lore raw

Re: [PATCH v4 04/16] media: i2c: Support 19.2MHz input clock in ov8865

Hi Andy

Quoted 22 lines · Andy Shevchenko
Quoted 5 lines · Daniel Scally

The ov8865 driver as written expects a 24MHz input clock, but the sensor is sometimes found on x86 platforms with a 19.2MHz input clock supplied. Add a set of PLL configurations to the driver to support that rate too. As ACPI doesn't auto-configure the clock rate, check for a clock-frequency during probe and set that rate if one is found.

...

Quoted 4 lines
drivers/media/i2c/ov8865.c +4 -0
+       /*
+        * We could have either a 24MHz or 19.2MHz clock rate. Check for a
+        * clock-frequency property and if found, set that rate. This should
+        * cover the ACPI case. If the system uses devicetree then the

drivers/media/i2c/ov8865.c static int ov8865_probe(struct i2c_client *client) · line 2933

Quoted 10 lines
drivers/media/i2c/ov8865.c +10 -0
+        * configured rate should already be set, so we'll have to check it.
+        */
+       ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
+                                      &rate);
+       if (!ret) {
+               ret = clk_set_rate(sensor->extclk, rate);
+               if (ret) {
+                       dev_err(dev, "failed to set clock rate\n");
+                       return ret;
+               }
Quoted 3 lines

dev_err_probe()
7065f92255bb ("driver core: Clarify that dev_err_probe() is OK even w/out -EPROBE_DEFER")

That cuts down on boilerplate usefully, thank you!

Quoted 15 lines
Quoted 2 lines

+ }

...

drivers/media/i2c/ov8865.c static int ov8865_probe(struct i2c_client *client) · line 2948

Quoted 11 lines
drivers/media/i2c/ov8865.c +8 -0
+       for (i = 0; i < ARRAY_SIZE(supported_extclk_rates); i++) {
+               if (sensor->extclk_rate == supported_extclk_rates[i])
+                       break;
+       }
+
+       if (i == ARRAY_SIZE(supported_extclk_rates)) {
+               dev_err(dev, "clock rate %lu Hz is unsupported\n",
+                       sensor->extclk_rate);
                ret = -EINVAL;
                goto error_endpoint;
        }
Quoted 2 lines

find_closest() ?

Not sure about this one though; the values might not match exactly, but if someone makes a device with this sensor supplying a totally different clock than 19.2MHz or 24MHz, it ought to fail here rather than attempt to continue I think

maintainer
#9 lore raw

Re: [PATCH v4 04/16] media: i2c: Support 19.2MHz input clock in ov8865

In reply to Daniel Scally

Hi Daniel,

Thanks for the set.

Quoted 169 lines · Daniel Scally

The ov8865 driver as written expects a 24MHz input clock, but the sensor is sometimes found on x86 platforms with a 19.2MHz input clock supplied. Add a set of PLL configurations to the driver to support that rate too. As ACPI doesn't auto-configure the clock rate, check for a clock-frequency during probe and set that rate if one is found.

---
 drivers/media/i2c/ov8865.c | 186 +++++++++++++++++++++++++++----------
 1 file changed, 135 insertions(+), 51 deletions(-)
drivers/media/i2c/ov8865.c +71 -27
index 9bc8d5d8199b..4ddc1b277cc0 100644
@@ -21,10 +21,6 @@
 #include <media/v4l2-image-sizes.h>
 #include <media/v4l2-mediabus.h>
 
-/* Clock rate */
-
-#define OV8865_EXTCLK_RATE			24000000
-
 /* Register definitions */
 
 /* System */
@@ -567,6 +563,25 @@ struct ov8865_sclk_config {
 	unsigned int sclk_div;
 };
 
+struct ov8865_pll_configs {
+	const struct ov8865_pll1_config *pll1_config;
+	const struct ov8865_pll2_config *pll2_config_native;
+	const struct ov8865_pll2_config *pll2_config_binning;
+};
+
+/* Clock rate */
+
+enum extclk_rate {
+	OV8865_19_2_MHZ,
+	OV8865_24_MHZ,
+	OV8865_NUM_SUPPORTED_RATES
+};
+
+static const unsigned long supported_extclk_rates[] = {
+	[OV8865_19_2_MHZ] = 19200000,
+	[OV8865_24_MHZ] = 24000000,
+};
+
 /*
  * General formulas for (array-centered) mode calculation:
  * - photo_array_width = 3296
@@ -635,9 +650,7 @@ struct ov8865_mode {
 
 	struct v4l2_fract frame_interval;
 
-	const struct ov8865_pll1_config *pll1_config;
-	const struct ov8865_pll2_config *pll2_config;
-	const struct ov8865_sclk_config *sclk_config;
+	bool pll2_binning;
 
 	const struct ov8865_register_value *register_values;
 	unsigned int register_values_count;
@@ -665,6 +678,9 @@ struct ov8865_sensor {
 	struct regulator *avdd;
 	struct regulator *dvdd;
 	struct regulator *dovdd;
+
+	unsigned long extclk_rate;
+	const struct ov8865_pll_configs *pll_configs;
 	struct clk *extclk;
 
 	struct v4l2_fwnode_endpoint endpoint;
@@ -680,43 +696,70 @@ struct ov8865_sensor {
 /* Static definitions */
 
 /*
- * EXTCLK = 24 MHz
  * PHY_SCLK = 720 MHz
  * MIPI_PCLK = 90 MHz
  */
-static const struct ov8865_pll1_config ov8865_pll1_config_native = {
-	.pll_pre_div_half	= 1,
-	.pll_pre_div		= 0,
-	.pll_mul		= 30,
-	.m_div			= 1,
-	.mipi_div		= 3,
-	.pclk_div		= 1,
-	.sys_pre_div		= 1,
-	.sys_div		= 2,
+
+static const struct ov8865_pll1_config ov8865_pll1_config_native_19_2mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 2,
+		.pll_mul		= 75,
+		.m_div			= 1,
+		.mipi_div		= 3,
+		.pclk_div		= 1,
+		.sys_pre_div		= 1,
+		.sys_div		= 2,
+};
+
+static const struct ov8865_pll1_config ov8865_pll1_config_native_24mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 0,
+		.pll_mul		= 30,
+		.m_div			= 1,
+		.mipi_div		= 3,
+		.pclk_div		= 1,
+		.sys_pre_div		= 1,
+		.sys_div		= 2,
 };
 
 /*
- * EXTCLK = 24 MHz
  * DAC_CLK = 360 MHz
  * SCLK = 144 MHz
  */
 
-static const struct ov8865_pll2_config ov8865_pll2_config_native = {
-	.pll_pre_div_half	= 1,
-	.pll_pre_div		= 0,
-	.pll_mul		= 30,
-	.dac_div		= 2,
-	.sys_pre_div		= 5,
-	.sys_div		= 0,
+static const struct ov8865_pll2_config ov8865_pll2_config_native_19_2mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 5,
+		.pll_mul		= 75,
+		.dac_div		= 1,
+		.sys_pre_div		= 1,
+		.sys_div		= 3,
+};
+
+static const struct ov8865_pll2_config ov8865_pll2_config_native_24mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 0,
+		.pll_mul		= 30,
+		.dac_div		= 2,
+		.sys_pre_div		= 5,
+		.sys_div		= 0,
 };
 
 /*
- * EXTCLK = 24 MHz
  * DAC_CLK = 360 MHz
  * SCLK = 72 MHz
  */
 
-static const struct ov8865_pll2_config ov8865_pll2_config_binning = {
+static const struct ov8865_pll2_config ov8865_pll2_config_binning_19_2mhz = {
+	.pll_pre_div_half	= 1,
+	.pll_pre_div		= 2,
+	.pll_mul		= 75,
+	.dac_div		= 2,
+	.sys_pre_div		= 10,
+	.sys_div		= 0,
+};
+
+static const struct ov8865_pll2_config ov8865_pll2_config_binning_24mhz = {
 	.pll_pre_div_half	= 1,
 	.pll_pre_div		= 0,
 	.pll_mul		= 30,
@@ -725,6 +768,23 @@ static const struct ov8865_pll2_config ov8865_pll2_config_binning = {
 	.sys_div		= 0,
 };
 
+static struct ov8865_pll_configs ov8865_pll_configs_19_2mhz = {

drivers/media/i2c/ov8865.c static const struct ov8865_pll2_config ov8865_pll2_config_binning = { · line 781

Quoted 10 lines
drivers/media/i2c/ov8865.c +10 -0
+	.pll1_config = &ov8865_pll1_config_native_19_2mhz,
+	.pll2_config_native = &ov8865_pll2_config_native_19_2mhz,
+	.pll2_config_binning = &ov8865_pll2_config_binning_19_2mhz,
+};
+
+static struct ov8865_pll_configs ov8865_pll_configs_24mhz = {
+	.pll1_config = &ov8865_pll1_config_native_24mhz,
+	.pll2_config_native = &ov8865_pll2_config_native_24mhz,
+	.pll2_config_binning = &ov8865_pll2_config_binning_24mhz,
+};

These should be const.

Quoted 143 lines
drivers/media/i2c/ov8865.c +33 -24
+
+static const struct ov8865_pll_configs *ov8865_pll_configs[] = {
+	&ov8865_pll_configs_19_2mhz,
+	&ov8865_pll_configs_24mhz,
+};
+
 static const struct ov8865_sclk_config ov8865_sclk_config_native = {
 	.sys_sel		= 1,
 	.sclk_sel		= 0,
@@ -934,9 +994,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 30 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_native,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= false,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_native,
@@ -990,9 +1048,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 30 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_native,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= false,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_native,
@@ -1050,9 +1106,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 30 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_binning,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= true,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_binning,
@@ -1116,9 +1170,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 90 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_binning,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= true,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_binning,
@@ -1513,12 +1565,11 @@ static int ov8865_isp_configure(struct ov8865_sensor *sensor)
 static unsigned long ov8865_mode_pll1_rate(struct ov8865_sensor *sensor,
 					   const struct ov8865_mode *mode)
 {
-	const struct ov8865_pll1_config *config = mode->pll1_config;
-	unsigned long extclk_rate;
+	const struct ov8865_pll1_config *config;
 	unsigned long pll1_rate;
 
-	extclk_rate = clk_get_rate(sensor->extclk);
-	pll1_rate = extclk_rate * config->pll_mul / config->pll_pre_div_half;
+	config = sensor->pll_configs->pll1_config;
+	pll1_rate = sensor->extclk_rate * config->pll_mul / config->pll_pre_div_half;
 
 	switch (config->pll_pre_div) {
 	case 0:
@@ -1552,10 +1603,12 @@ static int ov8865_mode_pll1_configure(struct ov8865_sensor *sensor,
 				      const struct ov8865_mode *mode,
 				      u32 mbus_code)
 {
-	const struct ov8865_pll1_config *config = mode->pll1_config;
+	const struct ov8865_pll1_config *config;
 	u8 value;
 	int ret;
 
+	config = sensor->pll_configs->pll1_config;
+
 	switch (mbus_code) {
 	case MEDIA_BUS_FMT_SBGGR10_1X10:
 		value = OV8865_MIPI_BIT_SEL(10);
@@ -1622,9 +1675,12 @@ static int ov8865_mode_pll1_configure(struct ov8865_sensor *sensor,
 static int ov8865_mode_pll2_configure(struct ov8865_sensor *sensor,
 				      const struct ov8865_mode *mode)
 {
-	const struct ov8865_pll2_config *config = mode->pll2_config;
+	const struct ov8865_pll2_config *config;
 	int ret;
 
+	config = mode->pll2_binning ? sensor->pll_configs->pll2_config_binning :
+				      sensor->pll_configs->pll2_config_native;
+
 	ret = ov8865_write(sensor, OV8865_PLL_CTRL12_REG,
 			   OV8865_PLL_CTRL12_PRE_DIV_HALF(config->pll_pre_div_half) |
 			   OV8865_PLL_CTRL12_DAC_DIV(config->dac_div));
@@ -1658,7 +1714,7 @@ static int ov8865_mode_pll2_configure(struct ov8865_sensor *sensor,
 static int ov8865_mode_sclk_configure(struct ov8865_sensor *sensor,
 				      const struct ov8865_mode *mode)
 {
-	const struct ov8865_sclk_config *config = mode->sclk_config;
+	const struct ov8865_sclk_config *config = &ov8865_sclk_config_native;
 	int ret;
 
 	ret = ov8865_write(sensor, OV8865_CLK_SEL0_REG,
@@ -2053,9 +2109,11 @@ static int ov8865_mode_configure(struct ov8865_sensor *sensor,
 static unsigned long ov8865_mode_mipi_clk_rate(struct ov8865_sensor *sensor,
 					       const struct ov8865_mode *mode)
 {
-	const struct ov8865_pll1_config *config = mode->pll1_config;
+	const struct ov8865_pll1_config *config;
 	unsigned long pll1_rate;
 
+	config = sensor->pll_configs->pll1_config;
+
 	pll1_rate = ov8865_mode_pll1_rate(sensor, mode);
 
 	return pll1_rate / config->m_div / 2;
@@ -2783,7 +2841,8 @@ static int ov8865_probe(struct i2c_client *client)
 	struct ov8865_sensor *sensor;
 	struct v4l2_subdev *subdev;
 	struct media_pad *pad;
-	unsigned long rate;
+	unsigned int rate;
+	unsigned int i;
 	int ret;
 
 	sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
@@ -2858,13 +2917,38 @@ static int ov8865_probe(struct i2c_client *client)
 		goto error_endpoint;
 	}
 
-	rate = clk_get_rate(sensor->extclk);
-	if (rate != OV8865_EXTCLK_RATE) {
-		dev_err(dev, "clock rate %lu Hz is unsupported\n", rate);
+	/*
+	 * We could have either a 24MHz or 19.2MHz clock rate. Check for a
+	 * clock-frequency property and if found, set that rate. This should
+	 * cover the ACPI case. If the system uses devicetree then the
+	 * configured rate should already be set, so we'll have to check it.
+	 */
+	ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",

drivers/media/i2c/ov8865.c static int ov8865_probe(struct i2c_client *client) · line 2936

Quoted 10 lines
drivers/media/i2c/ov8865.c +10 -0
+				       &rate);
+	if (!ret) {
+		ret = clk_set_rate(sensor->extclk, rate);
+		if (ret) {
+			dev_err(dev, "failed to set clock rate\n");
+			return ret;
+		}
+	}
+
+	sensor->extclk_rate = clk_get_rate(sensor->extclk);

clk_get_rate() returns 0 if you don't have a clock. But you can still have clock-frequency property that tells the frequency. This is generally the case on ACPI based systems apart from some exceptions (which I understand you're well aware of).

See e.g. drivers/media/i2c/ccs/ccs-core.c .

Quoted 18 lines
drivers/media/i2c/ov8865.c +11 -0
+
+	for (i = 0; i < ARRAY_SIZE(supported_extclk_rates); i++) {
+		if (sensor->extclk_rate == supported_extclk_rates[i])
+			break;
+	}
+
+	if (i == ARRAY_SIZE(supported_extclk_rates)) {
+		dev_err(dev, "clock rate %lu Hz is unsupported\n",
+			sensor->extclk_rate);
 		ret = -EINVAL;
 		goto error_endpoint;
 	}
 
+	sensor->pll_configs = ov8865_pll_configs[i];
+
 	/* Subdev, entity and pad */
 
 	subdev = &sensor->subdev;
Signature · 3 lines
Kind regards,

Sakari Ailus
#10 lore raw

Re: [PATCH v4 04/16] media: i2c: Support 19.2MHz input clock in ov8865

Hi Sakari - sorry, only just coming back to this series.

Quoted 5 lines · Sakari Ailus
Quoted 5 lines
drivers/media/i2c/ov8865.c +5 -0
+static struct ov8865_pll_configs ov8865_pll_configs_19_2mhz = {
+	.pll1_config = &ov8865_pll1_config_native_19_2mhz,
+	.pll2_config_native = &ov8865_pll2_config_native_19_2mhz,
+	.pll2_config_binning = &ov8865_pll2_config_binning_19_2mhz,
+};
Quoted 8 lines

drivers/media/i2c/ov8865.c static const struct ov8865_pll2_config ov8865_pll2_config_binning = { · line 781

Quoted 6 lines
drivers/media/i2c/ov8865.c +6 -0
+
+static struct ov8865_pll_configs ov8865_pll_configs_24mhz = {
+	.pll1_config = &ov8865_pll1_config_native_24mhz,
+	.pll2_config_native = &ov8865_pll2_config_native_24mhz,
+	.pll2_config_binning = &ov8865_pll2_config_binning_24mhz,
+};

These should be const.

Done, thank you.

Quoted 30 lines
Quoted 14 lines
drivers/media/i2c/ov8865.c +7 -3
@@ -2858,13 +2917,38 @@ static int ov8865_probe(struct i2c_client *client)
 		goto error_endpoint;
 	}
 
-	rate = clk_get_rate(sensor->extclk);
-	if (rate != OV8865_EXTCLK_RATE) {
-		dev_err(dev, "clock rate %lu Hz is unsupported\n", rate);
+	/*
+	 * We could have either a 24MHz or 19.2MHz clock rate. Check for a
+	 * clock-frequency property and if found, set that rate. This should
+	 * cover the ACPI case. If the system uses devicetree then the
+	 * configured rate should already be set, so we'll have to check it.
+	 */
+	ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",

drivers/media/i2c/ov8865.c static int ov8865_probe(struct i2c_client *client) · line 2936

Quoted 10 lines
drivers/media/i2c/ov8865.c +10 -0
+				       &rate);
+	if (!ret) {
+		ret = clk_set_rate(sensor->extclk, rate);
+		if (ret) {
+			dev_err(dev, "failed to set clock rate\n");
+			return ret;
+		}
+	}
+
+	sensor->extclk_rate = clk_get_rate(sensor->extclk);

clk_get_rate() returns 0 if you don't have a clock. But you can still have clock-frequency property that tells the frequency. This is generally the case on ACPI based systems apart from some exceptions (which I understand you're well aware of).

Quoted 1 line

See e.g. drivers/media/i2c/ccs/ccs-core.c .

I'm checking the clock-frequency property above...that should be sufficient here I think right?

Quoted 19 lines
Quoted 18 lines
drivers/media/i2c/ov8865.c +11 -0
+
+	for (i = 0; i < ARRAY_SIZE(supported_extclk_rates); i++) {
+		if (sensor->extclk_rate == supported_extclk_rates[i])
+			break;
+	}
+
+	if (i == ARRAY_SIZE(supported_extclk_rates)) {
+		dev_err(dev, "clock rate %lu Hz is unsupported\n",
+			sensor->extclk_rate);
 		ret = -EINVAL;
 		goto error_endpoint;
 	}
 
+	sensor->pll_configs = ov8865_pll_configs[i];
+
 	/* Subdev, entity and pad */
 
 	subdev = &sensor->subdev;
#11 lore raw

Re: [PATCH v4 04/16] media: i2c: Support 19.2MHz input clock in ov8865

In reply to Sakari Ailus

Hi Sakari

Quoted 344 lines · Sakari Ailus

Hi Daniel,

Thanks for the set.

Quoted 169 lines · Daniel Scally

The ov8865 driver as written expects a 24MHz input clock, but the sensor is sometimes found on x86 platforms with a 19.2MHz input clock supplied. Add a set of PLL configurations to the driver to support that rate too. As ACPI doesn't auto-configure the clock rate, check for a clock-frequency during probe and set that rate if one is found.

---
 drivers/media/i2c/ov8865.c | 186 +++++++++++++++++++++++++++----------
 1 file changed, 135 insertions(+), 51 deletions(-)
drivers/media/i2c/ov8865.c +71 -27
index 9bc8d5d8199b..4ddc1b277cc0 100644
@@ -21,10 +21,6 @@
 #include <media/v4l2-image-sizes.h>
 #include <media/v4l2-mediabus.h>
 
-/* Clock rate */
-
-#define OV8865_EXTCLK_RATE			24000000
-
 /* Register definitions */
 
 /* System */
@@ -567,6 +563,25 @@ struct ov8865_sclk_config {
 	unsigned int sclk_div;
 };
 
+struct ov8865_pll_configs {
+	const struct ov8865_pll1_config *pll1_config;
+	const struct ov8865_pll2_config *pll2_config_native;
+	const struct ov8865_pll2_config *pll2_config_binning;
+};
+
+/* Clock rate */
+
+enum extclk_rate {
+	OV8865_19_2_MHZ,
+	OV8865_24_MHZ,
+	OV8865_NUM_SUPPORTED_RATES
+};
+
+static const unsigned long supported_extclk_rates[] = {
+	[OV8865_19_2_MHZ] = 19200000,
+	[OV8865_24_MHZ] = 24000000,
+};
+
 /*
  * General formulas for (array-centered) mode calculation:
  * - photo_array_width = 3296
@@ -635,9 +650,7 @@ struct ov8865_mode {
 
 	struct v4l2_fract frame_interval;
 
-	const struct ov8865_pll1_config *pll1_config;
-	const struct ov8865_pll2_config *pll2_config;
-	const struct ov8865_sclk_config *sclk_config;
+	bool pll2_binning;
 
 	const struct ov8865_register_value *register_values;
 	unsigned int register_values_count;
@@ -665,6 +678,9 @@ struct ov8865_sensor {
 	struct regulator *avdd;
 	struct regulator *dvdd;
 	struct regulator *dovdd;
+
+	unsigned long extclk_rate;
+	const struct ov8865_pll_configs *pll_configs;
 	struct clk *extclk;
 
 	struct v4l2_fwnode_endpoint endpoint;
@@ -680,43 +696,70 @@ struct ov8865_sensor {
 /* Static definitions */
 
 /*
- * EXTCLK = 24 MHz
  * PHY_SCLK = 720 MHz
  * MIPI_PCLK = 90 MHz
  */
-static const struct ov8865_pll1_config ov8865_pll1_config_native = {
-	.pll_pre_div_half	= 1,
-	.pll_pre_div		= 0,
-	.pll_mul		= 30,
-	.m_div			= 1,
-	.mipi_div		= 3,
-	.pclk_div		= 1,
-	.sys_pre_div		= 1,
-	.sys_div		= 2,
+
+static const struct ov8865_pll1_config ov8865_pll1_config_native_19_2mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 2,
+		.pll_mul		= 75,
+		.m_div			= 1,
+		.mipi_div		= 3,
+		.pclk_div		= 1,
+		.sys_pre_div		= 1,
+		.sys_div		= 2,
+};
+
+static const struct ov8865_pll1_config ov8865_pll1_config_native_24mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 0,
+		.pll_mul		= 30,
+		.m_div			= 1,
+		.mipi_div		= 3,
+		.pclk_div		= 1,
+		.sys_pre_div		= 1,
+		.sys_div		= 2,
 };
 
 /*
- * EXTCLK = 24 MHz
  * DAC_CLK = 360 MHz
  * SCLK = 144 MHz
  */
 
-static const struct ov8865_pll2_config ov8865_pll2_config_native = {
-	.pll_pre_div_half	= 1,
-	.pll_pre_div		= 0,
-	.pll_mul		= 30,
-	.dac_div		= 2,
-	.sys_pre_div		= 5,
-	.sys_div		= 0,
+static const struct ov8865_pll2_config ov8865_pll2_config_native_19_2mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 5,
+		.pll_mul		= 75,
+		.dac_div		= 1,
+		.sys_pre_div		= 1,
+		.sys_div		= 3,
+};
+
+static const struct ov8865_pll2_config ov8865_pll2_config_native_24mhz = {
+		.pll_pre_div_half	= 1,
+		.pll_pre_div		= 0,
+		.pll_mul		= 30,
+		.dac_div		= 2,
+		.sys_pre_div		= 5,
+		.sys_div		= 0,
 };
 
 /*
- * EXTCLK = 24 MHz
  * DAC_CLK = 360 MHz
  * SCLK = 72 MHz
  */
 
-static const struct ov8865_pll2_config ov8865_pll2_config_binning = {
+static const struct ov8865_pll2_config ov8865_pll2_config_binning_19_2mhz = {
+	.pll_pre_div_half	= 1,
+	.pll_pre_div		= 2,
+	.pll_mul		= 75,
+	.dac_div		= 2,
+	.sys_pre_div		= 10,
+	.sys_div		= 0,
+};
+
+static const struct ov8865_pll2_config ov8865_pll2_config_binning_24mhz = {
 	.pll_pre_div_half	= 1,
 	.pll_pre_div		= 0,
 	.pll_mul		= 30,
@@ -725,6 +768,23 @@ static const struct ov8865_pll2_config ov8865_pll2_config_binning = {
 	.sys_div		= 0,
 };
 
+static struct ov8865_pll_configs ov8865_pll_configs_19_2mhz = {

drivers/media/i2c/ov8865.c static const struct ov8865_pll2_config ov8865_pll2_config_binning = { · line 781

Quoted 10 lines
drivers/media/i2c/ov8865.c +10 -0
+	.pll1_config = &ov8865_pll1_config_native_19_2mhz,
+	.pll2_config_native = &ov8865_pll2_config_native_19_2mhz,
+	.pll2_config_binning = &ov8865_pll2_config_binning_19_2mhz,
+};
+
+static struct ov8865_pll_configs ov8865_pll_configs_24mhz = {
+	.pll1_config = &ov8865_pll1_config_native_24mhz,
+	.pll2_config_native = &ov8865_pll2_config_native_24mhz,
+	.pll2_config_binning = &ov8865_pll2_config_binning_24mhz,
+};

These should be const.

Quoted 143 lines
drivers/media/i2c/ov8865.c +33 -24
+
+static const struct ov8865_pll_configs *ov8865_pll_configs[] = {
+	&ov8865_pll_configs_19_2mhz,
+	&ov8865_pll_configs_24mhz,
+};
+
 static const struct ov8865_sclk_config ov8865_sclk_config_native = {
 	.sys_sel		= 1,
 	.sclk_sel		= 0,
@@ -934,9 +994,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 30 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_native,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= false,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_native,
@@ -990,9 +1048,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 30 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_native,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= false,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_native,
@@ -1050,9 +1106,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 30 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_binning,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= true,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_binning,
@@ -1116,9 +1170,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.frame_interval			= { 1, 90 },
 
 		/* PLL */
-		.pll1_config			= &ov8865_pll1_config_native,
-		.pll2_config			= &ov8865_pll2_config_binning,
-		.sclk_config			= &ov8865_sclk_config_native,
+		.pll2_binning			= true,
 
 		/* Registers */
 		.register_values	= ov8865_register_values_binning,
@@ -1513,12 +1565,11 @@ static int ov8865_isp_configure(struct ov8865_sensor *sensor)
 static unsigned long ov8865_mode_pll1_rate(struct ov8865_sensor *sensor,
 					   const struct ov8865_mode *mode)
 {
-	const struct ov8865_pll1_config *config = mode->pll1_config;
-	unsigned long extclk_rate;
+	const struct ov8865_pll1_config *config;
 	unsigned long pll1_rate;
 
-	extclk_rate = clk_get_rate(sensor->extclk);
-	pll1_rate = extclk_rate * config->pll_mul / config->pll_pre_div_half;
+	config = sensor->pll_configs->pll1_config;
+	pll1_rate = sensor->extclk_rate * config->pll_mul / config->pll_pre_div_half;
 
 	switch (config->pll_pre_div) {
 	case 0:
@@ -1552,10 +1603,12 @@ static int ov8865_mode_pll1_configure(struct ov8865_sensor *sensor,
 				      const struct ov8865_mode *mode,
 				      u32 mbus_code)
 {
-	const struct ov8865_pll1_config *config = mode->pll1_config;
+	const struct ov8865_pll1_config *config;
 	u8 value;
 	int ret;
 
+	config = sensor->pll_configs->pll1_config;
+
 	switch (mbus_code) {
 	case MEDIA_BUS_FMT_SBGGR10_1X10:
 		value = OV8865_MIPI_BIT_SEL(10);
@@ -1622,9 +1675,12 @@ static int ov8865_mode_pll1_configure(struct ov8865_sensor *sensor,
 static int ov8865_mode_pll2_configure(struct ov8865_sensor *sensor,
 				      const struct ov8865_mode *mode)
 {
-	const struct ov8865_pll2_config *config = mode->pll2_config;
+	const struct ov8865_pll2_config *config;
 	int ret;
 
+	config = mode->pll2_binning ? sensor->pll_configs->pll2_config_binning :
+				      sensor->pll_configs->pll2_config_native;
+
 	ret = ov8865_write(sensor, OV8865_PLL_CTRL12_REG,
 			   OV8865_PLL_CTRL12_PRE_DIV_HALF(config->pll_pre_div_half) |
 			   OV8865_PLL_CTRL12_DAC_DIV(config->dac_div));
@@ -1658,7 +1714,7 @@ static int ov8865_mode_pll2_configure(struct ov8865_sensor *sensor,
 static int ov8865_mode_sclk_configure(struct ov8865_sensor *sensor,
 				      const struct ov8865_mode *mode)
 {
-	const struct ov8865_sclk_config *config = mode->sclk_config;
+	const struct ov8865_sclk_config *config = &ov8865_sclk_config_native;
 	int ret;
 
 	ret = ov8865_write(sensor, OV8865_CLK_SEL0_REG,
@@ -2053,9 +2109,11 @@ static int ov8865_mode_configure(struct ov8865_sensor *sensor,
 static unsigned long ov8865_mode_mipi_clk_rate(struct ov8865_sensor *sensor,
 					       const struct ov8865_mode *mode)
 {
-	const struct ov8865_pll1_config *config = mode->pll1_config;
+	const struct ov8865_pll1_config *config;
 	unsigned long pll1_rate;
 
+	config = sensor->pll_configs->pll1_config;
+
 	pll1_rate = ov8865_mode_pll1_rate(sensor, mode);
 
 	return pll1_rate / config->m_div / 2;
@@ -2783,7 +2841,8 @@ static int ov8865_probe(struct i2c_client *client)
 	struct ov8865_sensor *sensor;
 	struct v4l2_subdev *subdev;
 	struct media_pad *pad;
-	unsigned long rate;
+	unsigned int rate;
+	unsigned int i;
 	int ret;
 
 	sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
@@ -2858,13 +2917,38 @@ static int ov8865_probe(struct i2c_client *client)
 		goto error_endpoint;
 	}
 
-	rate = clk_get_rate(sensor->extclk);
-	if (rate != OV8865_EXTCLK_RATE) {
-		dev_err(dev, "clock rate %lu Hz is unsupported\n", rate);
+	/*
+	 * We could have either a 24MHz or 19.2MHz clock rate. Check for a
+	 * clock-frequency property and if found, set that rate. This should
+	 * cover the ACPI case. If the system uses devicetree then the
+	 * configured rate should already be set, so we'll have to check it.
+	 */
+	ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",

drivers/media/i2c/ov8865.c static int ov8865_probe(struct i2c_client *client) · line 2936

Quoted 10 lines
drivers/media/i2c/ov8865.c +10 -0
+				       &rate);
+	if (!ret) {
+		ret = clk_set_rate(sensor->extclk, rate);
+		if (ret) {
+			dev_err(dev, "failed to set clock rate\n");
+			return ret;
+		}
+	}
+
+	sensor->extclk_rate = clk_get_rate(sensor->extclk);

clk_get_rate() returns 0 if you don't have a clock. But you can still have clock-frequency property that tells the frequency. This is generally the case on ACPI based systems apart from some exceptions (which I understand you're well aware of).

Quoted 1 line

See e.g. drivers/media/i2c/ccs/ccs-core.c .

Sorry; misunderstood this in my previous reply, but having reviewed the code you told me to review I understand what you're saying now - I'll re-work it to follow the ccs-core methodology

Quoted 18 lines
Quoted 18 lines
drivers/media/i2c/ov8865.c +11 -0
+
+	for (i = 0; i < ARRAY_SIZE(supported_extclk_rates); i++) {
+		if (sensor->extclk_rate == supported_extclk_rates[i])
+			break;
+	}
+
+	if (i == ARRAY_SIZE(supported_extclk_rates)) {
+		dev_err(dev, "clock rate %lu Hz is unsupported\n",
+			sensor->extclk_rate);
 		ret = -EINVAL;
 		goto error_endpoint;
 	}
 
+	sensor->pll_configs = ov8865_pll_configs[i];
+
 	/* Subdev, entity and pad */
 
 	subdev = &sensor->subdev;
#12 lore raw

PATCH v4 5/16 media: i2c: Add .get_selection() support to ov8865

In reply to Daniel Scally

The ov8865 driver's v4l2_subdev_pad_ops currently does not include .get_selection() - add support for that callback.

---
 drivers/media/i2c/ov8865.c | 64 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)
drivers/media/i2c/ov8865.c +64 -0
index 4ddc1b277cc0..0f2776390a8e 100644
@@ -450,6 +450,15 @@
 #define OV8865_PRE_CTRL0_PATTERN_COLOR_SQUARES	2
 #define OV8865_PRE_CTRL0_PATTERN_BLACK		3
 
+/* Pixel Array */
+
+#define OV8865_NATIVE_WIDTH			3296
+#define OV8865_NATIVE_HEIGHT			2528
+#define OV8865_ACTIVE_START_TOP			32
+#define OV8865_ACTIVE_START_LEFT		80
+#define OV8865_ACTIVE_WIDTH			3264
+#define OV8865_ACTIVE_HEIGHT			2448
+
 /* Macros */
 
 #define ov8865_subdev_sensor(s) \
@@ -2756,12 +2765,67 @@ static int ov8865_enum_frame_interval(struct v4l2_subdev *subdev,
 	return 0;
 }
 
+static void
+__ov8865_get_pad_crop(struct ov8865_sensor *sensor,
+		      struct v4l2_subdev_state *state, unsigned int pad,
+		      enum v4l2_subdev_format_whence which, struct v4l2_rect *r)
+{
+	const struct ov8865_mode *mode = sensor->state.mode;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		*r = *v4l2_subdev_get_try_crop(&sensor->subdev, state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		r->height = mode->output_size_y;
+		r->width = mode->output_size_x;
+		r->top = (OV8865_NATIVE_HEIGHT - mode->output_size_y) / 2;
+		r->left = (OV8865_NATIVE_WIDTH - mode->output_size_x) / 2;
+		break;
+	}
+}
+
+static int ov8865_get_selection(struct v4l2_subdev *subdev,
+				struct v4l2_subdev_state *state,
+				struct v4l2_subdev_selection *sel)
+{
+	struct ov8865_sensor *sensor = ov8865_subdev_sensor(subdev);
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP:
+		mutex_lock(&sensor->mutex);
+			__ov8865_get_pad_crop(sensor, state, sel->pad,
+					      sel->which, &sel->r);
+		mutex_unlock(&sensor->mutex);
+		break;
+	case V4L2_SEL_TGT_NATIVE_SIZE:
+		sel->r.top = 0;
+		sel->r.left = 0;
+		sel->r.width = OV8865_NATIVE_WIDTH;
+		sel->r.height = OV8865_NATIVE_HEIGHT;
+		break;
+	case V4L2_SEL_TGT_CROP_BOUNDS:
+	case V4L2_SEL_TGT_CROP_DEFAULT:
+		sel->r.top = OV8865_ACTIVE_START_TOP;
+		sel->r.left = OV8865_ACTIVE_START_LEFT;
+		sel->r.width = OV8865_ACTIVE_WIDTH;
+		sel->r.height = OV8865_ACTIVE_HEIGHT;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
 static const struct v4l2_subdev_pad_ops ov8865_subdev_pad_ops = {
 	.enum_mbus_code		= ov8865_enum_mbus_code,
 	.get_fmt		= ov8865_get_fmt,
 	.set_fmt		= ov8865_set_fmt,
 	.enum_frame_size	= ov8865_enum_frame_size,
 	.enum_frame_interval	= ov8865_enum_frame_interval,
+	.get_selection		= ov8865_get_selection,
+	.set_selection		= ov8865_get_selection,
 };
 
 static const struct v4l2_subdev_ops ov8865_subdev_ops = {
Signature · 1 line
2.25.1
#13 lore raw

PATCH v4 6/16 media: i2c: Switch control to V4L2_CID_ANALOGUE_GAIN

In reply to Daniel Scally

The V4L2_CID_GAIN control for this driver configures registers that the datasheet specifies as analogue gain. Switch the control's ID to V4L2_CID_ANALOGUE_GAIN.

---
 drivers/media/i2c/ov8865.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/media/i2c/ov8865.c +5 -4
index 0f2776390a8e..a832938c33b6 100644
@@ -2150,7 +2150,7 @@ static int ov8865_exposure_configure(struct ov8865_sensor *sensor, u32 exposure)
 
 /* Gain */
 
-static int ov8865_gain_configure(struct ov8865_sensor *sensor, u32 gain)
+static int ov8865_analog_gain_configure(struct ov8865_sensor *sensor, u32 gain)
 {
 	int ret;
 
@@ -2460,8 +2460,8 @@ static int ov8865_s_ctrl(struct v4l2_ctrl *ctrl)
 		if (ret)
 			return ret;
 		break;
-	case V4L2_CID_GAIN:
-		ret = ov8865_gain_configure(sensor, ctrl->val);
+	case V4L2_CID_ANALOGUE_GAIN:
+		ret = ov8865_analog_gain_configure(sensor, ctrl->val);
 		if (ret)
 			return ret;
 		break;
@@ -2506,7 +2506,8 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 
 	/* Gain */
 
-	v4l2_ctrl_new_std(handler, ops, V4L2_CID_GAIN, 128, 8191, 128, 128);
+	v4l2_ctrl_new_std(handler, ops, V4L2_CID_ANALOGUE_GAIN, 128, 8191, 128,
+			  128);
 
 	/* White Balance */
 
Signature · 1 line
2.25.1
#14 lore raw

PATCH v4 7/16 media: i2c: Add vblank control to ov8865

In reply to Daniel Scally

Add a V4L2_CID_VBLANK control to the ov8865 driver.

---
 drivers/media/i2c/ov8865.c | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)
drivers/media/i2c/ov8865.c +34 -0
index a832938c33b6..f741c0713ca4 100644
@@ -183,6 +183,8 @@
 #define OV8865_VTS_H(v)				(((v) & GENMASK(11, 8)) >> 8)
 #define OV8865_VTS_L_REG			0x380f
 #define OV8865_VTS_L(v)				((v) & GENMASK(7, 0))
+#define OV8865_TIMING_MAX_VTS			0xffff
+#define OV8865_TIMING_MIN_VTS			0x04
 #define OV8865_OFFSET_X_H_REG			0x3810
 #define OV8865_OFFSET_X_H(v)			(((v) & GENMASK(15, 8)) >> 8)
 #define OV8865_OFFSET_X_L_REG			0x3811
@@ -675,6 +677,7 @@ struct ov8865_state {
 struct ov8865_ctrls {
 	struct v4l2_ctrl *link_freq;
 	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *vblank;
 
 	struct v4l2_ctrl_handler handler;
 };
@@ -2225,6 +2228,20 @@ static int ov8865_test_pattern_configure(struct ov8865_sensor *sensor,
 			    ov8865_test_pattern_bits[index]);
 }
 
+/* Blanking */
+
+static int ov8865_vts_configure(struct ov8865_sensor *sensor, u32 vblank)
+{
+	u16 vts = sensor->state.mode->output_size_y + vblank;
+	int ret;
+
+	ret = ov8865_write(sensor, OV8865_VTS_H_REG, OV8865_VTS_H(vts));
+	if (ret)
+		return ret;
+
+	return ov8865_write(sensor, OV8865_VTS_L_REG, OV8865_VTS_L(vts));
+}
+
 /* State */
 
 static int ov8865_state_mipi_configure(struct ov8865_sensor *sensor,
@@ -2476,6 +2493,8 @@ static int ov8865_s_ctrl(struct v4l2_ctrl *ctrl)
 	case V4L2_CID_TEST_PATTERN:
 		index = (unsigned int)ctrl->val;
 		return ov8865_test_pattern_configure(sensor, index);
+	case V4L2_CID_VBLANK:
+		return ov8865_vts_configure(sensor, ctrl->val);
 	default:
 		return -EINVAL;
 	}
@@ -2492,6 +2511,8 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 	struct ov8865_ctrls *ctrls = &sensor->ctrls;
 	struct v4l2_ctrl_handler *handler = &ctrls->handler;
 	const struct v4l2_ctrl_ops *ops = &ov8865_ctrl_ops;
+	const struct ov8865_mode *mode = sensor->state.mode;
+	unsigned int vblank_max, vblank_def;
 	int ret;
 
 	v4l2_ctrl_handler_init(handler, 32);
@@ -2528,6 +2549,13 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 				     ARRAY_SIZE(ov8865_test_pattern_menu) - 1,
 				     0, 0, ov8865_test_pattern_menu);
 
+	/* Blanking */
+	vblank_max = OV8865_TIMING_MAX_VTS - mode->output_size_y;
+	vblank_def = mode->vts - mode->output_size_y;
+	ctrls->vblank = v4l2_ctrl_new_std(handler, ops, V4L2_CID_VBLANK,
+					  OV8865_TIMING_MIN_VTS, vblank_max, 1,
+					  vblank_def);
+
 	/* MIPI CSI-2 */
 
 	ctrls->link_freq =
@@ -2708,6 +2736,10 @@ static int ov8865_set_fmt(struct v4l2_subdev *subdev,
 		 sensor->state.mbus_code != mbus_code)
 		ret = ov8865_state_configure(sensor, mode, mbus_code);
 
+	__v4l2_ctrl_modify_range(sensor->ctrls.vblank, OV8865_TIMING_MIN_VTS,
+				 OV8865_TIMING_MAX_VTS - mode->output_size_y,
+				 1, mode->vts - mode->output_size_y);
+
 complete:
 	mutex_unlock(&sensor->mutex);
 
@@ -3035,6 +3067,8 @@ static int ov8865_probe(struct i2c_client *client)
 
 	/* Sensor */
 
+	sensor->state.mode =  &ov8865_modes[0];
+
 	ret = ov8865_ctrls_init(sensor);
 	if (ret)
 		goto error_mutex;
Signature · 1 line
2.25.1
maintainer
#15 lore raw

Re: [PATCH v4 07/16] media: i2c: Add vblank control to ov8865

Hi Daniel,

Quoted 93 lines · Daniel Scally

Add a V4L2_CID_VBLANK control to the ov8865 driver.

---
 drivers/media/i2c/ov8865.c | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)
drivers/media/i2c/ov8865.c +32 -0
index a832938c33b6..f741c0713ca4 100644
@@ -183,6 +183,8 @@
 #define OV8865_VTS_H(v)				(((v) & GENMASK(11, 8)) >> 8)
 #define OV8865_VTS_L_REG			0x380f
 #define OV8865_VTS_L(v)				((v) & GENMASK(7, 0))
+#define OV8865_TIMING_MAX_VTS			0xffff
+#define OV8865_TIMING_MIN_VTS			0x04
 #define OV8865_OFFSET_X_H_REG			0x3810
 #define OV8865_OFFSET_X_H(v)			(((v) & GENMASK(15, 8)) >> 8)
 #define OV8865_OFFSET_X_L_REG			0x3811
@@ -675,6 +677,7 @@ struct ov8865_state {
 struct ov8865_ctrls {
 	struct v4l2_ctrl *link_freq;
 	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *vblank;
 
 	struct v4l2_ctrl_handler handler;
 };
@@ -2225,6 +2228,20 @@ static int ov8865_test_pattern_configure(struct ov8865_sensor *sensor,
 			    ov8865_test_pattern_bits[index]);
 }
 
+/* Blanking */
+
+static int ov8865_vts_configure(struct ov8865_sensor *sensor, u32 vblank)
+{
+	u16 vts = sensor->state.mode->output_size_y + vblank;
+	int ret;
+
+	ret = ov8865_write(sensor, OV8865_VTS_H_REG, OV8865_VTS_H(vts));
+	if (ret)
+		return ret;
+
+	return ov8865_write(sensor, OV8865_VTS_L_REG, OV8865_VTS_L(vts));
+}
+
 /* State */
 
 static int ov8865_state_mipi_configure(struct ov8865_sensor *sensor,
@@ -2476,6 +2493,8 @@ static int ov8865_s_ctrl(struct v4l2_ctrl *ctrl)
 	case V4L2_CID_TEST_PATTERN:
 		index = (unsigned int)ctrl->val;
 		return ov8865_test_pattern_configure(sensor, index);
+	case V4L2_CID_VBLANK:
+		return ov8865_vts_configure(sensor, ctrl->val);
 	default:
 		return -EINVAL;
 	}
@@ -2492,6 +2511,8 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 	struct ov8865_ctrls *ctrls = &sensor->ctrls;
 	struct v4l2_ctrl_handler *handler = &ctrls->handler;
 	const struct v4l2_ctrl_ops *ops = &ov8865_ctrl_ops;
+	const struct ov8865_mode *mode = sensor->state.mode;
+	unsigned int vblank_max, vblank_def;
 	int ret;
 
 	v4l2_ctrl_handler_init(handler, 32);
@@ -2528,6 +2549,13 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 				     ARRAY_SIZE(ov8865_test_pattern_menu) - 1,
 				     0, 0, ov8865_test_pattern_menu);
 
+	/* Blanking */
+	vblank_max = OV8865_TIMING_MAX_VTS - mode->output_size_y;
+	vblank_def = mode->vts - mode->output_size_y;
+	ctrls->vblank = v4l2_ctrl_new_std(handler, ops, V4L2_CID_VBLANK,
+					  OV8865_TIMING_MIN_VTS, vblank_max, 1,
+					  vblank_def);
+
 	/* MIPI CSI-2 */
 
 	ctrls->link_freq =
@@ -2708,6 +2736,10 @@ static int ov8865_set_fmt(struct v4l2_subdev *subdev,
 		 sensor->state.mbus_code != mbus_code)
 		ret = ov8865_state_configure(sensor, mode, mbus_code);
 
+	__v4l2_ctrl_modify_range(sensor->ctrls.vblank, OV8865_TIMING_MIN_VTS,
+				 OV8865_TIMING_MAX_VTS - mode->output_size_y,
+				 1, mode->vts - mode->output_size_y);
+
 complete:
 	mutex_unlock(&sensor->mutex);
 

drivers/media/i2c/ov8865.c static int ov8865_probe(struct i2c_client *client) · line 3070

Quoted 4 lines
drivers/media/i2c/ov8865.c +1 -0
@@ -3035,6 +3067,8 @@ static int ov8865_probe(struct i2c_client *client)
 
 	/* Sensor */
 
+	sensor->state.mode =  &ov8865_modes[0];

This seems to be an unrelated change. Does it belong here?

Quoted 4 lines
drivers/media/i2c/ov8865.c +1 -0
+
 	ret = ov8865_ctrls_init(sensor);
 	if (ret)
 		goto error_mutex;
Signature · 3 lines
Regards,

Sakari Ailus
#16 lore raw

Re: [PATCH v4 07/16] media: i2c: Add vblank control to ov8865

Hi Sakari

Quoted 95 lines · Sakari Ailus

Hi Daniel,

Quoted 92 lines · Daniel Scally

Add a V4L2_CID_VBLANK control to the ov8865 driver.

---
 drivers/media/i2c/ov8865.c | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)
drivers/media/i2c/ov8865.c +32 -0
index a832938c33b6..f741c0713ca4 100644
@@ -183,6 +183,8 @@
 #define OV8865_VTS_H(v)				(((v) & GENMASK(11, 8)) >> 8)
 #define OV8865_VTS_L_REG			0x380f
 #define OV8865_VTS_L(v)				((v) & GENMASK(7, 0))
+#define OV8865_TIMING_MAX_VTS			0xffff
+#define OV8865_TIMING_MIN_VTS			0x04
 #define OV8865_OFFSET_X_H_REG			0x3810
 #define OV8865_OFFSET_X_H(v)			(((v) & GENMASK(15, 8)) >> 8)
 #define OV8865_OFFSET_X_L_REG			0x3811
@@ -675,6 +677,7 @@ struct ov8865_state {
 struct ov8865_ctrls {
 	struct v4l2_ctrl *link_freq;
 	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *vblank;
 
 	struct v4l2_ctrl_handler handler;
 };
@@ -2225,6 +2228,20 @@ static int ov8865_test_pattern_configure(struct ov8865_sensor *sensor,
 			    ov8865_test_pattern_bits[index]);
 }
 
+/* Blanking */
+
+static int ov8865_vts_configure(struct ov8865_sensor *sensor, u32 vblank)
+{
+	u16 vts = sensor->state.mode->output_size_y + vblank;
+	int ret;
+
+	ret = ov8865_write(sensor, OV8865_VTS_H_REG, OV8865_VTS_H(vts));
+	if (ret)
+		return ret;
+
+	return ov8865_write(sensor, OV8865_VTS_L_REG, OV8865_VTS_L(vts));
+}
+
 /* State */
 
 static int ov8865_state_mipi_configure(struct ov8865_sensor *sensor,
@@ -2476,6 +2493,8 @@ static int ov8865_s_ctrl(struct v4l2_ctrl *ctrl)
 	case V4L2_CID_TEST_PATTERN:
 		index = (unsigned int)ctrl->val;
 		return ov8865_test_pattern_configure(sensor, index);
+	case V4L2_CID_VBLANK:
+		return ov8865_vts_configure(sensor, ctrl->val);
 	default:
 		return -EINVAL;
 	}
@@ -2492,6 +2511,8 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 	struct ov8865_ctrls *ctrls = &sensor->ctrls;
 	struct v4l2_ctrl_handler *handler = &ctrls->handler;
 	const struct v4l2_ctrl_ops *ops = &ov8865_ctrl_ops;
+	const struct ov8865_mode *mode = sensor->state.mode;
+	unsigned int vblank_max, vblank_def;
 	int ret;
 
 	v4l2_ctrl_handler_init(handler, 32);
@@ -2528,6 +2549,13 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 				     ARRAY_SIZE(ov8865_test_pattern_menu) - 1,
 				     0, 0, ov8865_test_pattern_menu);
 
+	/* Blanking */
+	vblank_max = OV8865_TIMING_MAX_VTS - mode->output_size_y;
+	vblank_def = mode->vts - mode->output_size_y;
+	ctrls->vblank = v4l2_ctrl_new_std(handler, ops, V4L2_CID_VBLANK,
+					  OV8865_TIMING_MIN_VTS, vblank_max, 1,
+					  vblank_def);
+
 	/* MIPI CSI-2 */
 
 	ctrls->link_freq =
@@ -2708,6 +2736,10 @@ static int ov8865_set_fmt(struct v4l2_subdev *subdev,
 		 sensor->state.mbus_code != mbus_code)
 		ret = ov8865_state_configure(sensor, mode, mbus_code);
 
+	__v4l2_ctrl_modify_range(sensor->ctrls.vblank, OV8865_TIMING_MIN_VTS,
+				 OV8865_TIMING_MAX_VTS - mode->output_size_y,
+				 1, mode->vts - mode->output_size_y);
+
 complete:
 	mutex_unlock(&sensor->mutex);
 
Quoted 6 lines

drivers/media/i2c/ov8865.c static int ov8865_probe(struct i2c_client *client) · line 3070

Quoted 5 lines
drivers/media/i2c/ov8865.c +1 -0
@@ -3035,6 +3067,8 @@ static int ov8865_probe(struct i2c_client *client)
 
 	/* Sensor */
 
+	sensor->state.mode =  &ov8865_modes[0];

This seems to be an unrelated change. Does it belong here?

In ov8865_ctrls_init() I'm using sensor->state.mode to initialise the new vblank control. I guess instead of

+ const struct ov8865_mode *mode = sensor->state.mode;

I could have

+ const struct ov8865_mode *mode = &ov8865_modes[0];

in that function though

Quoted 5 lines
Quoted 5 lines
drivers/media/i2c/ov8865.c +1 -0
+
 	ret = ov8865_ctrls_init(sensor);
 	if (ret)
 		goto error_mutex;
maintainer
#17 lore raw

Re: [PATCH v4 07/16] media: i2c: Add vblank control to ov8865

Hi Daniel,

Quoted 117 lines · Daniel Scally

Hi Sakari

Quoted 95 lines · Sakari Ailus

Hi Daniel,

Quoted 92 lines · Daniel Scally

Add a V4L2_CID_VBLANK control to the ov8865 driver.

---
 drivers/media/i2c/ov8865.c | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)
drivers/media/i2c/ov8865.c +32 -0
index a832938c33b6..f741c0713ca4 100644
@@ -183,6 +183,8 @@
 #define OV8865_VTS_H(v)				(((v) & GENMASK(11, 8)) >> 8)
 #define OV8865_VTS_L_REG			0x380f
 #define OV8865_VTS_L(v)				((v) & GENMASK(7, 0))
+#define OV8865_TIMING_MAX_VTS			0xffff
+#define OV8865_TIMING_MIN_VTS			0x04
 #define OV8865_OFFSET_X_H_REG			0x3810
 #define OV8865_OFFSET_X_H(v)			(((v) & GENMASK(15, 8)) >> 8)
 #define OV8865_OFFSET_X_L_REG			0x3811
@@ -675,6 +677,7 @@ struct ov8865_state {
 struct ov8865_ctrls {
 	struct v4l2_ctrl *link_freq;
 	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *vblank;
 
 	struct v4l2_ctrl_handler handler;
 };
@@ -2225,6 +2228,20 @@ static int ov8865_test_pattern_configure(struct ov8865_sensor *sensor,
 			    ov8865_test_pattern_bits[index]);
 }
 
+/* Blanking */
+
+static int ov8865_vts_configure(struct ov8865_sensor *sensor, u32 vblank)
+{
+	u16 vts = sensor->state.mode->output_size_y + vblank;
+	int ret;
+
+	ret = ov8865_write(sensor, OV8865_VTS_H_REG, OV8865_VTS_H(vts));
+	if (ret)
+		return ret;
+
+	return ov8865_write(sensor, OV8865_VTS_L_REG, OV8865_VTS_L(vts));
+}
+
 /* State */
 
 static int ov8865_state_mipi_configure(struct ov8865_sensor *sensor,
@@ -2476,6 +2493,8 @@ static int ov8865_s_ctrl(struct v4l2_ctrl *ctrl)
 	case V4L2_CID_TEST_PATTERN:
 		index = (unsigned int)ctrl->val;
 		return ov8865_test_pattern_configure(sensor, index);
+	case V4L2_CID_VBLANK:
+		return ov8865_vts_configure(sensor, ctrl->val);
 	default:
 		return -EINVAL;
 	}
@@ -2492,6 +2511,8 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 	struct ov8865_ctrls *ctrls = &sensor->ctrls;
 	struct v4l2_ctrl_handler *handler = &ctrls->handler;
 	const struct v4l2_ctrl_ops *ops = &ov8865_ctrl_ops;
+	const struct ov8865_mode *mode = sensor->state.mode;
+	unsigned int vblank_max, vblank_def;
 	int ret;
 
 	v4l2_ctrl_handler_init(handler, 32);
@@ -2528,6 +2549,13 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 				     ARRAY_SIZE(ov8865_test_pattern_menu) - 1,
 				     0, 0, ov8865_test_pattern_menu);
 
+	/* Blanking */
+	vblank_max = OV8865_TIMING_MAX_VTS - mode->output_size_y;
+	vblank_def = mode->vts - mode->output_size_y;
+	ctrls->vblank = v4l2_ctrl_new_std(handler, ops, V4L2_CID_VBLANK,
+					  OV8865_TIMING_MIN_VTS, vblank_max, 1,
+					  vblank_def);
+
 	/* MIPI CSI-2 */
 
 	ctrls->link_freq =
@@ -2708,6 +2736,10 @@ static int ov8865_set_fmt(struct v4l2_subdev *subdev,
 		 sensor->state.mbus_code != mbus_code)
 		ret = ov8865_state_configure(sensor, mode, mbus_code);
 
+	__v4l2_ctrl_modify_range(sensor->ctrls.vblank, OV8865_TIMING_MIN_VTS,
+				 OV8865_TIMING_MAX_VTS - mode->output_size_y,
+				 1, mode->vts - mode->output_size_y);
+
 complete:
 	mutex_unlock(&sensor->mutex);
 
Quoted 6 lines

drivers/media/i2c/ov8865.c static int ov8865_probe(struct i2c_client *client) · line 3070

Quoted 5 lines
drivers/media/i2c/ov8865.c +1 -0
@@ -3035,6 +3067,8 @@ static int ov8865_probe(struct i2c_client *client)
 
 	/* Sensor */
 
+	sensor->state.mode =  &ov8865_modes[0];

This seems to be an unrelated change. Does it belong here?

In ov8865_ctrls_init() I'm using sensor->state.mode to initialise the new vblank control. I guess instead of

drivers/media/i2c/ov8865.c +1 -0
+	const struct ov8865_mode *mode = sensor->state.mode;

I could have

(quoted diff) +1 -0
+	const struct ov8865_mode *mode = &ov8865_modes[0];
Quoted 1 line

in that function though

You're right indeed.

ov8865_state_init() refers to the same mode. I think it'd be cleaner if you'd e.g. call ov8865_state_configure() with sensor->state.mode instead, so that you don't initialise the same variable in two places.

Signature · 3 lines
Kind regards,

Sakari Ailus
#18 lore raw

PATCH v4 8/16 media: i2c: Add hblank control to ov8865

In reply to Daniel Scally

Add a V4L2_CID_HBLANK control to the ov8865 driver. This is read only with timing control intended to be done via vblanking alone.

---
 drivers/media/i2c/ov8865.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
drivers/media/i2c/ov8865.c +14 -0
index f741c0713ca4..4b18cc80f985 100644
@@ -677,6 +677,7 @@ struct ov8865_state {
 struct ov8865_ctrls {
 	struct v4l2_ctrl *link_freq;
 	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *hblank;
 	struct v4l2_ctrl *vblank;
 
 	struct v4l2_ctrl_handler handler;
@@ -2513,6 +2514,7 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 	const struct v4l2_ctrl_ops *ops = &ov8865_ctrl_ops;
 	const struct ov8865_mode *mode = sensor->state.mode;
 	unsigned int vblank_max, vblank_def;
+	unsigned int hblank;
 	int ret;
 
 	v4l2_ctrl_handler_init(handler, 32);
@@ -2550,6 +2552,13 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 				     0, 0, ov8865_test_pattern_menu);
 
 	/* Blanking */
+	hblank = mode->hts - mode->output_size_x;
+	ctrls->hblank = v4l2_ctrl_new_std(handler, ops, V4L2_CID_HBLANK, hblank,
+					  hblank, 1, hblank);
+
+	if (ctrls->hblank)
+		ctrls->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
 	vblank_max = OV8865_TIMING_MAX_VTS - mode->output_size_y;
 	vblank_def = mode->vts - mode->output_size_y;
 	ctrls->vblank = v4l2_ctrl_new_std(handler, ops, V4L2_CID_VBLANK,
@@ -2696,6 +2705,7 @@ static int ov8865_set_fmt(struct v4l2_subdev *subdev,
 	struct v4l2_mbus_framefmt *mbus_format = &format->format;
 	const struct ov8865_mode *mode;
 	u32 mbus_code = 0;
+	unsigned int hblank;
 	unsigned int index;
 	int ret = 0;
 
@@ -2740,6 +2750,10 @@ static int ov8865_set_fmt(struct v4l2_subdev *subdev,
 				 OV8865_TIMING_MAX_VTS - mode->output_size_y,
 				 1, mode->vts - mode->output_size_y);
 
+	hblank = mode->hts - mode->output_size_x;
+	__v4l2_ctrl_modify_range(sensor->ctrls.hblank, hblank, hblank, 1,
+				 hblank);
+
 complete:
 	mutex_unlock(&sensor->mutex);
 
Signature · 1 line
2.25.1
#19 lore raw

PATCH v4 9/16 media: i2c: Update HTS values in ov8865

In reply to Daniel Scally

The HTS values for some of the modes in the ov8865 driver are a bit unusual, coming in lower than the output_size_x is set to. It seems like they might be calculated to fit the desired framerate into a configuration with just two data lanes. To bring this more in line with expected behaviour, raise the HTS values above the output_size_x.

The corollary of that change is that the hardcoded frame intervals against the modes no longer make sense, so remove those entirely. Update the .g/s_frame_interval() callbacks to calculate the frame interval based on the current mode and the vblank and hblank settings.

The implementation of the .enum_frame_interval() callback is no longer suitable since the possible frame rate is now a continuous range depending on the vblank control setting, so remove that callback entirely.

---
 drivers/media/i2c/ov8865.c | 65 +++++++-------------------------------
 1 file changed, 11 insertions(+), 54 deletions(-)
drivers/media/i2c/ov8865.c +11 -54
index 4b18cc80f985..1b8674152750 100644
@@ -659,8 +659,6 @@ struct ov8865_mode {
 	unsigned int blc_anchor_right_start;
 	unsigned int blc_anchor_right_end;
 
-	struct v4l2_fract frame_interval;
-
 	bool pll2_binning;
 
 	const struct ov8865_register_value *register_values;
@@ -964,7 +962,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 	{
 		/* Horizontal */
 		.output_size_x			= 3264,
-		.hts				= 1944,
+		.hts				= 3888,
 
 		/* Vertical */
 		.output_size_y			= 2448,
@@ -1003,9 +1001,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 1984,
 		.blc_anchor_right_end		= 2239,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 30 },
-
 		/* PLL */
 		.pll2_binning			= false,
 
@@ -1018,11 +1013,11 @@ static const struct ov8865_mode ov8865_modes[] = {
 	{
 		/* Horizontal */
 		.output_size_x			= 3264,
-		.hts				= 2582,
+		.hts				= 3888,
 
 		/* Vertical */
 		.output_size_y			= 1836,
-		.vts				= 2002,
+		.vts				= 2470,
 
 		.size_auto			= true,
 		.size_auto_boundary_x		= 8,
@@ -1057,9 +1052,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 1984,
 		.blc_anchor_right_end		= 2239,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 30 },
-
 		/* PLL */
 		.pll2_binning			= false,
 
@@ -1115,9 +1107,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 992,
 		.blc_anchor_right_end		= 1119,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 30 },
-
 		/* PLL */
 		.pll2_binning			= true,
 
@@ -1179,9 +1168,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 992,
 		.blc_anchor_right_end		= 1119,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 90 },
-
 		/* PLL */
 		.pll2_binning			= true,
 
@@ -2628,11 +2614,18 @@ static int ov8865_g_frame_interval(struct v4l2_subdev *subdev,
 {
 	struct ov8865_sensor *sensor = ov8865_subdev_sensor(subdev);
 	const struct ov8865_mode *mode;
+	unsigned int framesize;
+	unsigned int fps;
 
 	mutex_lock(&sensor->mutex);
 
 	mode = sensor->state.mode;
-	interval->interval = mode->frame_interval;
+	framesize = mode->hts * (mode->output_size_y +
+				 sensor->ctrls.vblank->val);
+	fps = DIV_ROUND_CLOSEST(sensor->ctrls.pixel_rate->val, framesize);
+
+	interval->interval.numerator = 1;
+	interval->interval.denominator = fps;
 
 	mutex_unlock(&sensor->mutex);
 
@@ -2777,41 +2770,6 @@ static int ov8865_enum_frame_size(struct v4l2_subdev *subdev,
 	return 0;
 }
 
-static int ov8865_enum_frame_interval(struct v4l2_subdev *subdev,
-				      struct v4l2_subdev_state *sd_state,
-				      struct v4l2_subdev_frame_interval_enum *interval_enum)
-{
-	const struct ov8865_mode *mode = NULL;
-	unsigned int mode_index;
-	unsigned int interval_index;
-
-	if (interval_enum->index > 0)
-		return -EINVAL;
-	/*
-	 * Multiple modes with the same dimensions may have different frame
-	 * intervals, so look up each relevant mode.
-	 */
-	for (mode_index = 0, interval_index = 0;
-	     mode_index < ARRAY_SIZE(ov8865_modes); mode_index++) {
-		mode = &ov8865_modes[mode_index];
-
-		if (mode->output_size_x == interval_enum->width &&
-		    mode->output_size_y == interval_enum->height) {
-			if (interval_index == interval_enum->index)
-				break;
-
-			interval_index++;
-		}
-	}
-
-	if (mode_index == ARRAY_SIZE(ov8865_modes))
-		return -EINVAL;
-
-	interval_enum->interval = mode->frame_interval;
-
-	return 0;
-}
-
 static void
 __ov8865_get_pad_crop(struct ov8865_sensor *sensor,
 		      struct v4l2_subdev_state *state, unsigned int pad,
@@ -2870,7 +2828,6 @@ static const struct v4l2_subdev_pad_ops ov8865_subdev_pad_ops = {
 	.get_fmt		= ov8865_get_fmt,
 	.set_fmt		= ov8865_set_fmt,
 	.enum_frame_size	= ov8865_enum_frame_size,
-	.enum_frame_interval	= ov8865_enum_frame_interval,
 	.get_selection		= ov8865_get_selection,
 	.set_selection		= ov8865_get_selection,
 };
Signature · 1 line
2.25.1
maintainer
#20 lore raw

Re: [PATCH v4 09/16] media: i2c: Update HTS values in ov8865

Hi Daniel,

Quoted 5 lines · Daniel Scally

The HTS values for some of the modes in the ov8865 driver are a bit unusual, coming in lower than the output_size_x is set to. It seems like they might be calculated to fit the desired framerate into a configuration with just two data lanes. To bring this more in line with expected behaviour, raise the HTS values above the output_size_x.

This isn't necessarily a problem as binning may be done in analogue domain. I don't know about this sensor though.

Is the frame interval still as expected in binned modes after this patch?

Quoted 161 lines

The corollary of that change is that the hardcoded frame intervals against the modes no longer make sense, so remove those entirely. Update the .g/s_frame_interval() callbacks to calculate the frame interval based on the current mode and the vblank and hblank settings.

The implementation of the .enum_frame_interval() callback is no longer suitable since the possible frame rate is now a continuous range depending on the vblank control setting, so remove that callback entirely.

---
 drivers/media/i2c/ov8865.c | 65 +++++++-------------------------------
 1 file changed, 11 insertions(+), 54 deletions(-)
drivers/media/i2c/ov8865.c +11 -54
index 4b18cc80f985..1b8674152750 100644
@@ -659,8 +659,6 @@ struct ov8865_mode {
 	unsigned int blc_anchor_right_start;
 	unsigned int blc_anchor_right_end;
 
-	struct v4l2_fract frame_interval;
-
 	bool pll2_binning;
 
 	const struct ov8865_register_value *register_values;
@@ -964,7 +962,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 	{
 		/* Horizontal */
 		.output_size_x			= 3264,
-		.hts				= 1944,
+		.hts				= 3888,
 
 		/* Vertical */
 		.output_size_y			= 2448,
@@ -1003,9 +1001,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 1984,
 		.blc_anchor_right_end		= 2239,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 30 },
-
 		/* PLL */
 		.pll2_binning			= false,
 
@@ -1018,11 +1013,11 @@ static const struct ov8865_mode ov8865_modes[] = {
 	{
 		/* Horizontal */
 		.output_size_x			= 3264,
-		.hts				= 2582,
+		.hts				= 3888,
 
 		/* Vertical */
 		.output_size_y			= 1836,
-		.vts				= 2002,
+		.vts				= 2470,
 
 		.size_auto			= true,
 		.size_auto_boundary_x		= 8,
@@ -1057,9 +1052,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 1984,
 		.blc_anchor_right_end		= 2239,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 30 },
-
 		/* PLL */
 		.pll2_binning			= false,
 
@@ -1115,9 +1107,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 992,
 		.blc_anchor_right_end		= 1119,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 30 },
-
 		/* PLL */
 		.pll2_binning			= true,
 
@@ -1179,9 +1168,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 992,
 		.blc_anchor_right_end		= 1119,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 90 },
-
 		/* PLL */
 		.pll2_binning			= true,
 
@@ -2628,11 +2614,18 @@ static int ov8865_g_frame_interval(struct v4l2_subdev *subdev,
 {
 	struct ov8865_sensor *sensor = ov8865_subdev_sensor(subdev);
 	const struct ov8865_mode *mode;
+	unsigned int framesize;
+	unsigned int fps;
 
 	mutex_lock(&sensor->mutex);
 
 	mode = sensor->state.mode;
-	interval->interval = mode->frame_interval;
+	framesize = mode->hts * (mode->output_size_y +
+				 sensor->ctrls.vblank->val);
+	fps = DIV_ROUND_CLOSEST(sensor->ctrls.pixel_rate->val, framesize);
+
+	interval->interval.numerator = 1;
+	interval->interval.denominator = fps;
 
 	mutex_unlock(&sensor->mutex);
 
@@ -2777,41 +2770,6 @@ static int ov8865_enum_frame_size(struct v4l2_subdev *subdev,
 	return 0;
 }
 
-static int ov8865_enum_frame_interval(struct v4l2_subdev *subdev,
-				      struct v4l2_subdev_state *sd_state,
-				      struct v4l2_subdev_frame_interval_enum *interval_enum)
-{
-	const struct ov8865_mode *mode = NULL;
-	unsigned int mode_index;
-	unsigned int interval_index;
-
-	if (interval_enum->index > 0)
-		return -EINVAL;
-	/*
-	 * Multiple modes with the same dimensions may have different frame
-	 * intervals, so look up each relevant mode.
-	 */
-	for (mode_index = 0, interval_index = 0;
-	     mode_index < ARRAY_SIZE(ov8865_modes); mode_index++) {
-		mode = &ov8865_modes[mode_index];
-
-		if (mode->output_size_x == interval_enum->width &&
-		    mode->output_size_y == interval_enum->height) {
-			if (interval_index == interval_enum->index)
-				break;
-
-			interval_index++;
-		}
-	}
-
-	if (mode_index == ARRAY_SIZE(ov8865_modes))
-		return -EINVAL;
-
-	interval_enum->interval = mode->frame_interval;
-
-	return 0;
-}
-
 static void
 __ov8865_get_pad_crop(struct ov8865_sensor *sensor,
 		      struct v4l2_subdev_state *state, unsigned int pad,
@@ -2870,7 +2828,6 @@ static const struct v4l2_subdev_pad_ops ov8865_subdev_pad_ops = {
 	.get_fmt		= ov8865_get_fmt,
 	.set_fmt		= ov8865_set_fmt,
 	.enum_frame_size	= ov8865_enum_frame_size,
-	.enum_frame_interval	= ov8865_enum_frame_interval,
 	.get_selection		= ov8865_get_selection,
 	.set_selection		= ov8865_get_selection,
 };
Signature · 3 lines
Kind regards,

Sakari Ailus
#21 lore raw

Re: [PATCH v4 09/16] media: i2c: Update HTS values in ov8865

Hi Sakari

Quoted 8 lines · Sakari Ailus

Hi Daniel,

Quoted 5 lines · Daniel Scally

The HTS values for some of the modes in the ov8865 driver are a bit unusual, coming in lower than the output_size_x is set to. It seems like they might be calculated to fit the desired framerate into a configuration with just two data lanes. To bring this more in line with expected behaviour, raise the HTS values above the output_size_x.

Quoted 4 lines

This isn't necessarily a problem as binning may be done in analogue domain. I don't know about this sensor though.

Is the frame interval still as expected in binned modes after this patch?

Actually none of the modes have binning in the X dimension set on. The ones with Y binning still have the framerates I expect, and the only modes who's HTS values I'm changing here don't use binning at all

Quoted 161 lines
Quoted 161 lines

The corollary of that change is that the hardcoded frame intervals against the modes no longer make sense, so remove those entirely. Update the .g/s_frame_interval() callbacks to calculate the frame interval based on the current mode and the vblank and hblank settings.

The implementation of the .enum_frame_interval() callback is no longer suitable since the possible frame rate is now a continuous range depending on the vblank control setting, so remove that callback entirely.

---
 drivers/media/i2c/ov8865.c | 65 +++++++-------------------------------
 1 file changed, 11 insertions(+), 54 deletions(-)
drivers/media/i2c/ov8865.c +11 -54
index 4b18cc80f985..1b8674152750 100644
@@ -659,8 +659,6 @@ struct ov8865_mode {
 	unsigned int blc_anchor_right_start;
 	unsigned int blc_anchor_right_end;
 
-	struct v4l2_fract frame_interval;
-
 	bool pll2_binning;
 
 	const struct ov8865_register_value *register_values;
@@ -964,7 +962,7 @@ static const struct ov8865_mode ov8865_modes[] = {
 	{
 		/* Horizontal */
 		.output_size_x			= 3264,
-		.hts				= 1944,
+		.hts				= 3888,
 
 		/* Vertical */
 		.output_size_y			= 2448,
@@ -1003,9 +1001,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 1984,
 		.blc_anchor_right_end		= 2239,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 30 },
-
 		/* PLL */
 		.pll2_binning			= false,
 
@@ -1018,11 +1013,11 @@ static const struct ov8865_mode ov8865_modes[] = {
 	{
 		/* Horizontal */
 		.output_size_x			= 3264,
-		.hts				= 2582,
+		.hts				= 3888,
 
 		/* Vertical */
 		.output_size_y			= 1836,
-		.vts				= 2002,
+		.vts				= 2470,
 
 		.size_auto			= true,
 		.size_auto_boundary_x		= 8,
@@ -1057,9 +1052,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 1984,
 		.blc_anchor_right_end		= 2239,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 30 },
-
 		/* PLL */
 		.pll2_binning			= false,
 
@@ -1115,9 +1107,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 992,
 		.blc_anchor_right_end		= 1119,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 30 },
-
 		/* PLL */
 		.pll2_binning			= true,
 
@@ -1179,9 +1168,6 @@ static const struct ov8865_mode ov8865_modes[] = {
 		.blc_anchor_right_start		= 992,
 		.blc_anchor_right_end		= 1119,
 
-		/* Frame Interval */
-		.frame_interval			= { 1, 90 },
-
 		/* PLL */
 		.pll2_binning			= true,
 
@@ -2628,11 +2614,18 @@ static int ov8865_g_frame_interval(struct v4l2_subdev *subdev,
 {
 	struct ov8865_sensor *sensor = ov8865_subdev_sensor(subdev);
 	const struct ov8865_mode *mode;
+	unsigned int framesize;
+	unsigned int fps;
 
 	mutex_lock(&sensor->mutex);
 
 	mode = sensor->state.mode;
-	interval->interval = mode->frame_interval;
+	framesize = mode->hts * (mode->output_size_y +
+				 sensor->ctrls.vblank->val);
+	fps = DIV_ROUND_CLOSEST(sensor->ctrls.pixel_rate->val, framesize);
+
+	interval->interval.numerator = 1;
+	interval->interval.denominator = fps;
 
 	mutex_unlock(&sensor->mutex);
 
@@ -2777,41 +2770,6 @@ static int ov8865_enum_frame_size(struct v4l2_subdev *subdev,
 	return 0;
 }
 
-static int ov8865_enum_frame_interval(struct v4l2_subdev *subdev,
-				      struct v4l2_subdev_state *sd_state,
-				      struct v4l2_subdev_frame_interval_enum *interval_enum)
-{
-	const struct ov8865_mode *mode = NULL;
-	unsigned int mode_index;
-	unsigned int interval_index;
-
-	if (interval_enum->index > 0)
-		return -EINVAL;
-	/*
-	 * Multiple modes with the same dimensions may have different frame
-	 * intervals, so look up each relevant mode.
-	 */
-	for (mode_index = 0, interval_index = 0;
-	     mode_index < ARRAY_SIZE(ov8865_modes); mode_index++) {
-		mode = &ov8865_modes[mode_index];
-
-		if (mode->output_size_x == interval_enum->width &&
-		    mode->output_size_y == interval_enum->height) {
-			if (interval_index == interval_enum->index)
-				break;
-
-			interval_index++;
-		}
-	}
-
-	if (mode_index == ARRAY_SIZE(ov8865_modes))
-		return -EINVAL;
-
-	interval_enum->interval = mode->frame_interval;
-
-	return 0;
-}
-
 static void
 __ov8865_get_pad_crop(struct ov8865_sensor *sensor,
 		      struct v4l2_subdev_state *state, unsigned int pad,
@@ -2870,7 +2828,6 @@ static const struct v4l2_subdev_pad_ops ov8865_subdev_pad_ops = {
 	.get_fmt		= ov8865_get_fmt,
 	.set_fmt		= ov8865_set_fmt,
 	.enum_frame_size	= ov8865_enum_frame_size,
-	.enum_frame_interval	= ov8865_enum_frame_interval,
 	.get_selection		= ov8865_get_selection,
 	.set_selection		= ov8865_get_selection,
 };
#22 lore raw

PATCH v4 10/16 media: i2c: cap exposure at height + vblank in ov8865

In reply to Daniel Scally

Exposure limits depend on the total height; when vblank is altered (and thus the total height is altered), change the exposure limits to reflect the new cap.

---
 drivers/media/i2c/ov8865.c | 26 ++++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)
drivers/media/i2c/ov8865.c +24 -2
index 1b8674152750..99548ad15dcd 100644
@@ -677,6 +677,7 @@ struct ov8865_ctrls {
 	struct v4l2_ctrl *pixel_rate;
 	struct v4l2_ctrl *hblank;
 	struct v4l2_ctrl *vblank;
+	struct v4l2_ctrl *exposure;
 
 	struct v4l2_ctrl_handler handler;
 };
@@ -2454,6 +2455,19 @@ static int ov8865_s_ctrl(struct v4l2_ctrl *ctrl)
 	unsigned int index;
 	int ret;
 
+	/* If VBLANK is altered we need to update exposure to compensate */
+	if (ctrl->id == V4L2_CID_VBLANK) {
+		int exposure_max;
+
+		exposure_max = sensor->state.mode->output_size_y + ctrl->val;
+		__v4l2_ctrl_modify_range(sensor->ctrls.exposure,
+					 sensor->ctrls.exposure->minimum,
+					 exposure_max,
+					 sensor->ctrls.exposure->step,
+					 min(sensor->ctrls.exposure->val,
+					     exposure_max));
+	}
+
 	/* Wait for the sensor to be on before setting controls. */
 	if (pm_runtime_suspended(sensor->dev))
 		return 0;
@@ -2510,8 +2524,8 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 
 	/* Exposure */
 
-	v4l2_ctrl_new_std(handler, ops, V4L2_CID_EXPOSURE, 16, 1048575, 16,
-			  512);
+	ctrls->exposure = v4l2_ctrl_new_std(handler, ops, V4L2_CID_EXPOSURE, 16,
+					    1048575, 16, 512);
 
 	/* Gain */
 
@@ -2700,6 +2714,7 @@ static int ov8865_set_fmt(struct v4l2_subdev *subdev,
 	u32 mbus_code = 0;
 	unsigned int hblank;
 	unsigned int index;
+	int exposure_max;
 	int ret = 0;
 
 	mutex_lock(&sensor->mutex);
@@ -2747,6 +2762,13 @@ static int ov8865_set_fmt(struct v4l2_subdev *subdev,
 	__v4l2_ctrl_modify_range(sensor->ctrls.hblank, hblank, hblank, 1,
 				 hblank);
 
+	exposure_max = mode->vts;
+	__v4l2_ctrl_modify_range(sensor->ctrls.exposure,
+				 sensor->ctrls.exposure->minimum, exposure_max,
+				 sensor->ctrls.exposure->step,
+				 min(sensor->ctrls.exposure->val,
+				     exposure_max));
+
 complete:
 	mutex_unlock(&sensor->mutex);
 
Signature · 1 line
2.25.1
#23 lore raw

PATCH v4 11/16 media: i2c: Add controls from fwnode to ov8865

In reply to Daniel Scally

Add V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION controls to the ov8865 driver by attempting to parse them from firmware.

---
 drivers/media/i2c/ov8865.c | 10 ++++++++++
 1 file changed, 10 insertions(+)
drivers/media/i2c/ov8865.c +10 -0
index 99548ad15dcd..dfb5095ef16b 100644
@@ -2513,6 +2513,7 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 	struct v4l2_ctrl_handler *handler = &ctrls->handler;
 	const struct v4l2_ctrl_ops *ops = &ov8865_ctrl_ops;
 	const struct ov8865_mode *mode = sensor->state.mode;
+	struct v4l2_fwnode_device_properties props;
 	unsigned int vblank_max, vblank_def;
 	unsigned int hblank;
 	int ret;
@@ -2576,6 +2577,15 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 		v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE, 1,
 				  INT_MAX, 1, 1);
 
+	/* set properties from fwnode (e.g. rotation, orientation) */
+	ret = v4l2_fwnode_device_parse(sensor->dev, &props);
+	if (ret)
+		goto error_ctrls;
+
+	ret = v4l2_ctrl_new_fwnode_properties(handler, ops, &props);
+	if (ret)
+		goto error_ctrls;
+
 	if (handler->error) {
 		ret = handler->error;
 		goto error_ctrls;
Signature · 1 line
2.25.1
#24 lore raw

PATCH v4 12/16 media: i2c: Switch exposure control unit to lines

In reply to Daniel Scally

The ov8865 driver currently has the unit of the V4L2_CID_EXPOSURE control as 1/16th of a line. This is what the sensor expects, but isn't very intuitive. Switch the control to be in units of a line and simply do the 16x multiplication before passing the value to the sensor.

The datasheet for this sensor gives minimum exposure as 2 lines, so take the opportunity to correct the lower bounds of the control.

---
 drivers/media/i2c/ov8865.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/media/i2c/ov8865.c +5 -2
index dfb5095ef16b..5f19d82554df 100644
@@ -2125,6 +2125,9 @@ static int ov8865_exposure_configure(struct ov8865_sensor *sensor, u32 exposure)
 {
 	int ret;
 
+	/* The sensor stores exposure in units of 1/16th of a line */
+	exposure *= 16;
+
 	ret = ov8865_write(sensor, OV8865_EXPOSURE_CTRL_HH_REG,
 			   OV8865_EXPOSURE_CTRL_HH(exposure));
 	if (ret)
@@ -2525,8 +2528,8 @@ static int ov8865_ctrls_init(struct ov8865_sensor *sensor)
 
 	/* Exposure */
 
-	ctrls->exposure = v4l2_ctrl_new_std(handler, ops, V4L2_CID_EXPOSURE, 16,
-					    1048575, 16, 512);
+	ctrls->exposure = v4l2_ctrl_new_std(handler, ops, V4L2_CID_EXPOSURE, 2,
+					    65535, 1, 32);
 
 	/* Gain */
 
Signature · 1 line
2.25.1
#25 lore raw

PATCH v4 13/16 media: i2c: Re-order runtime pm initialisation

In reply to Daniel Scally

The kerneldoc for pm_runtime_set_suspended() says:

"It is not valid to call this function for devices with runtime PM enabled"

To satisfy that requirement, re-order the calls so that pm_runtime_enable() is the last one.

---
 drivers/media/i2c/ov8865.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/media/i2c/ov8865.c +1 -1
index 5f19d82554df..18b5f1e8e9a7 100644
@@ -3085,8 +3085,8 @@ static int ov8865_probe(struct i2c_client *client)
 
 	/* Runtime PM */
 
-	pm_runtime_enable(sensor->dev);
 	pm_runtime_set_suspended(sensor->dev);
+	pm_runtime_enable(sensor->dev);
 
 	/* V4L2 subdev register */
 
Signature · 1 line
2.25.1
#26 lore raw

Re: [PATCH v4 13/16] media: i2c: Re-order runtime pm initialisation

Quoted 7 lines · Daniel Scally

The kerneldoc for pm_runtime_set_suspended() says:

"It is not valid to call this function for devices with runtime PM enabled"

To satisfy that requirement, re-order the calls so that pm_runtime_enable() is the last one.

Shouldn't this be a fix with Fixes tag applied?

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#27 lore raw

Re: [PATCH v4 13/16] media: i2c: Re-order runtime pm initialisation

Hi Andy

Quoted 10 lines · Andy Shevchenko
Quoted 7 lines · Daniel Scally

The kerneldoc for pm_runtime_set_suspended() says:

"It is not valid to call this function for devices with runtime PM enabled"

To satisfy that requirement, re-order the calls so that pm_runtime_enable() is the last one.

Shouldn't this be a fix with Fixes tag applied?

Yes I guess so - thanks, I'll add it

#28 lore raw

PATCH v4 14/16 media: i2c: Use dev_err_probe() in ov8865

In reply to Daniel Scally

There is a chance that regulator_get() returns -EPROBE_DEFER, in which case printing an error message is undesirable. To avoid spurious messages in dmesg in the event that -EPROBE_DEFER is returned, use dev_err_probe() on error paths for regulator_get().

---
 drivers/media/i2c/ov8865.c | 46 +++++++++++++++++---------------------
 1 file changed, 20 insertions(+), 26 deletions(-)
drivers/media/i2c/ov8865.c +20 -26
index 18b5f1e8e9a7..ab225fb616b9 100644
@@ -2955,6 +2955,26 @@ static int ov8865_probe(struct i2c_client *client)
 	sensor->dev = dev;
 	sensor->i2c_client = client;
 
+	/* Regulators */
+
+	/* DVDD: digital core */
+	sensor->dvdd = devm_regulator_get(dev, "dvdd");
+	if (IS_ERR(sensor->dvdd))
+		return dev_err_probe(dev, PTR_ERR(sensor->dvdd),
+				     "cannot get DVDD regulator\n");
+
+	/* DOVDD: digital I/O */
+	sensor->dovdd = devm_regulator_get(dev, "dovdd");
+	if (IS_ERR(sensor->dovdd))
+		return dev_err_probe(dev, PTR_ERR(sensor->dovdd),
+				     "cannot get DOVDD regulator\n");
+
+	/* AVDD: analog */
+	sensor->avdd = devm_regulator_get(dev, "avdd");
+	if (IS_ERR(sensor->avdd))
+		return dev_err_probe(dev, PTR_ERR(sensor->avdd),
+				     "cannot get AVDD (analog) regulator\n");
+
 	/* Graph Endpoint */
 
 	handle = fwnode_graph_get_next_endpoint(dev_fwnode(dev), NULL);
@@ -2985,32 +3005,6 @@ static int ov8865_probe(struct i2c_client *client)
 		goto error_endpoint;
 	}
 
-	/* Regulators */
-
-	/* DVDD: digital core */
-	sensor->dvdd = devm_regulator_get(dev, "dvdd");
-	if (IS_ERR(sensor->dvdd)) {
-		dev_err(dev, "cannot get DVDD (digital core) regulator\n");
-		ret = PTR_ERR(sensor->dvdd);
-		goto error_endpoint;
-	}
-
-	/* DOVDD: digital I/O */
-	sensor->dovdd = devm_regulator_get(dev, "dovdd");
-	if (IS_ERR(sensor->dovdd)) {
-		dev_err(dev, "cannot get DOVDD (digital I/O) regulator\n");
-		ret = PTR_ERR(sensor->dovdd);
-		goto error_endpoint;
-	}
-
-	/* AVDD: analog */
-	sensor->avdd = devm_regulator_get(dev, "avdd");
-	if (IS_ERR(sensor->avdd)) {
-		dev_err(dev, "cannot get AVDD (analog) regulator\n");
-		ret = PTR_ERR(sensor->avdd);
-		goto error_endpoint;
-	}
-
 	/* External Clock */
 
 	sensor->extclk = devm_clk_get(dev, NULL);
Signature · 1 line
2.25.1
#29 lore raw

PATCH v4 15/16 media: ipu3-cio2: Add INT347A to cio2-bridge

In reply to Daniel Scally

ACPI _HID INT347A represents the OV8865 sensor, the driver for which can support the platforms that the cio2-bridge serves. Add it to the array of supported sensors so the bridge will connect the sensor to the CIO2 device.

---
 drivers/media/pci/intel/ipu3/cio2-bridge.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/media/pci/intel/ipu3/cio2-bridge.c +2 -0
index 59a36f922675..fb7d708b16e2 100644
@@ -22,6 +22,8 @@
 static const struct cio2_sensor_config cio2_supported_sensors[] = {
 	/* Omnivision OV5693 */
 	CIO2_SENSOR_CONFIG("INT33BE", 0),
+	/* Omnivision OV8865 */
+	CIO2_SENSOR_CONFIG("INT347A", 1, 360000000),
 	/* Omnivision OV2680 */
 	CIO2_SENSOR_CONFIG("OVTI2680", 0),
 };
Signature · 1 line
2.25.1
#30 lore raw

PATCH v4 16/16 media: i2c: ov8865: Fix lockdep error

In reply to Daniel Scally

From: Hans de Goede <[email protected]>

ov8865_state_init() calls ov8865_state_mipi_configure() which uses __v4l2_ctrl_s_ctrl[_int64](). This means that sensor->mutex (which is also sensor->ctrls.handler.lock) must be locked before calling ov8865_state_init().

Note ov8865_state_mipi_configure() is also used in other places where the lock is already held so it cannot be changed itself.

This fixes the following lockdep kernel WARN:

[   13.233413] ------------[ cut here ]------------
[   13.233421] WARNING: CPU: 0 PID: 8 at drivers/media/v4l2-core/v4l2-ctrls-api.c:833 __v4l2_ctrl_s_ctrl+0x4d/0x60 [videodev]
...
[   13.234063] Call Trace:
[   13.234074]  ov8865_state_configure+0x98b/0xc00 [ov8865]
[   13.234095]  ov8865_probe+0x4b1/0x54c [ov8865]
[   13.234117]  i2c_device_probe+0x13c/0x2d0
---
 drivers/media/i2c/ov8865.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/media/i2c/ov8865.c +2 -0
index ab225fb616b9..c5fe290317e8 100644
@@ -3073,7 +3073,9 @@ static int ov8865_probe(struct i2c_client *client)
 	if (ret)
 		goto error_mutex;
 
+	mutex_lock(&sensor->mutex);
 	ret = ov8865_state_init(sensor);
+	mutex_unlock(&sensor->mutex);
 	if (ret)
 		goto error_ctrls;
 
Signature · 1 line
2.25.1
#31 lore raw

Re: [PATCH v4 16/16] media: i2c: ov8865: Fix lockdep error

Quoted 7 lines · Daniel Scally

From: Hans de Goede <[email protected]>

ov8865_state_init() calls ov8865_state_mipi_configure() which uses __v4l2_ctrl_s_ctrl[_int64](). This means that sensor->mutex (which is also sensor->ctrls.handler.lock) must be locked before calling ov8865_state_init().

Quoted 6 lines

Note ov8865_state_mipi_configure() is also used in other places where the lock is already held so it cannot be changed itself.

This fixes the following lockdep kernel WARN:

[   13.233413] ------------[ cut here ]------------

You may drop this noisy line.

Quoted 6 lines
[   13.233421] WARNING: CPU: 0 PID: 8 at drivers/media/v4l2-core/v4l2-ctrls-api.c:833 __v4l2_ctrl_s_ctrl+0x4d/0x60 [videodev]
...
[   13.234063] Call Trace:
[   13.234074]  ov8865_state_configure+0x98b/0xc00 [ov8865]
[   13.234095]  ov8865_probe+0x4b1/0x54c [ov8865]
[   13.234117]  i2c_device_probe+0x13c/0x2d0

Seems to me that this should be moved to the head of the series with Fixes tag added.

Signature · 2 lines
With Best Regards,
Andy Shevchenko