arm64: dts: ti: k3-am64-main: Add GPMC & ELM nodes
Subsystems (2)
cover arm64: dts: ti: k3-am64-main: Add GPMC & ELM nodes
Hi Nishanth,
This series adds GPMC and ELM controller nodes.
cheers,
-roger
Roger Quadros (2):
arm64: dts: ti: k3-am64-main: Add GPMC memory controller node
arm64: dts: ti: k3-am64-main: Add ELM (Error Location Module) node
arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 28 ++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
Signature · 1 line
2.17.1
PATCH 1/2 arm64: dts: ti: k3-am64-main: Add GPMC memory controller node
The GPMC is a unified memory controller dedicated for interfacing with external memory devices like
- Asynchronous SRAM-like memories and ASICs
- Asynchronous, synchronous, and page mode burst NOR flash
- NAND flash
- Pseudo-SRAM devices
--- arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +19 -0
@@ -1253,4 +1253,23 @@ bus_freq = <1000000>; }; }; + + gpmc0: memory-controller@3b000000 { + compatible = "ti,am64-gpmc"; + power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 80 0>; + clock-names = "fck"; + reg = <0x00 0x03b000000 0x00 0x2000>, + <0x00 0x050000000 0x00 0x7FFFFFF>; + reg-names = "cfg", "data"; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; + gpmc,num-cs = <3>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; };
Signature · 1 line
2.17.1
PATCH 2/2 arm64: dts: ti: k3-am64-main: Add ELM (Error Location Module) node
In reply to Roger QuadrosThe ELM module is used for GPMC NAND accesses for detecting and correcting errors during reads due to NAND bitflips errors.
4-, 8-, and 16-bit error-correction levels are supported using the BCH (Bose-ChaudhurI-Hocquenghem) algorithm.
--- arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +9 -0
@@ -1272,4 +1272,13 @@ gpio-controller; #gpio-cells = <2>; }; + + elm0: ecc@25010000 { + compatible = "ti,am3352-elm"; + reg = <0x00 0x25010000 0x00 0x2000>; + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&k3_pds 54 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 54 0>; + clock-names = "fck"; + }; };
Signature · 1 line
2.17.1
Nishanth Menon
maintainerQuoted 7 lines · Roger Quadros
Hi Nishanth,
This series adds GPMC and ELM controller nodes.
cheers,
-roger
Quoted 10 lines
Roger Quadros (2):
arm64: dts: ti: k3-am64-main: Add GPMC memory controller node
arm64: dts: ti: k3-am64-main: Add ELM (Error Location Module) nodearch/arm64/boot/dts/ti/k3-am64-main.dtsi | 28 ++++++++++++++++++++++++ 1 file changed, 28 insertions(+)Signature · 1 line
2.17.1
Don't we need to disable the nodes in the board dts files, since these are only on optional daughter cards for evm?
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Quoted 15 lines · Nishanth Menon
Quoted 14 lines · Roger Quadros
Hi Nishanth,
This series adds GPMC and ELM controller nodes.
cheers,
-rogerRoger Quadros (2):
arm64: dts: ti: k3-am64-main: Add GPMC memory controller node
arm64: dts: ti: k3-am64-main: Add ELM (Error Location Module) nodearch/arm64/boot/dts/ti/k3-am64-main.dtsi | 28 ++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
Quoted 7 lines
Quoted 3 lines
Signature · 1 line
2.17.1Don't we need to disable the nodes in the board dts files, since these are only on optional daughter cards for evm?
Yes. Will fix it up in v2.
cheers,
-roger
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel