MediaTek Ethernet Patches on MT8195
Subsystems (6)
v8 cover MediaTek Ethernet Patches on MT8195
Changes in v8:
1. add acked-by in "stmmac: dwmac-mediatek: add platform level clocks management" patch
Changes in v7:
1. fix uninitialized warning as Jakub's comments.
Changes in v6:
1. update commit message as Jakub's comments.
2. split mt8195 eth dts patch("arm64: dts: mt8195: add ethernet device node") from this series, since mt8195 dtsi/dts basic patches is still under reviewing.
https://patchwork.kernel.org/project/linux-mediatek/list/?series=579071
we'll resend mt8195 eth dts patch once all the dependent patches are accepted.
Changes in v5:
1. remove useless inclusion in dwmac-mediatek.c as Angelo's comments.
2. add acked-by in "net-next: stmmac: dwmac-mediatek: add support for mt8195" patch
Changes in v4:
1. add changes in commit message in "net-next: dt-bindings: dwmac:
Convert mediatek-dwmac to DT schema" patch.
2. remove ethernet-controller.yaml since snps,dwmac.yaml already include it.
Changes in v3:
1. Add prefix "net-next" to support new IC as Denis's suggestion.
2. Split dt-bindings to two patches, one for conversion, and the other for new IC.
3. add a new patch to update device node in mt2712-evb.dts to accommodate to changes in driver.
4. remove unnecessary wrapper as Angelo's suggestion.
5. Add acked-by in "net-next: stmmac: dwmac-mediatek: Reuse more common features" patch.
Changes in v2:
1. fix errors/warnings in mediatek-dwmac.yaml with upgraded dtschema tools
This series include 5 patches:
1. add platform level clocks management for dwmac-mediatek
2. resue more common features defined in stmmac_platform.c
3. add ethernet entry for mt8195
4. convert mediatek-dwmac.txt to mediatek-dwmac.yaml
Biao Huang (6):
stmmac: dwmac-mediatek: add platform level clocks management
stmmac: dwmac-mediatek: Reuse more common features
arm64: dts: mt2712: update ethernet device node
net: dt-bindings: dwmac: Convert mediatek-dwmac to DT schema
stmmac: dwmac-mediatek: add support for mt8195
net: dt-bindings: dwmac: add support for mt8195
.../bindings/net/mediatek-dwmac.txt | 91 ------ .../bindings/net/mediatek-dwmac.yaml | 210 ++++++++++++ arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 1 + arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 14 +- .../ethernet/stmicro/stmmac/dwmac-mediatek.c | 306 ++++++++++++++++-- 5 files changed, 503 insertions(+), 119 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.txt create mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
--
2.18.0
PATCH v8 1/6 stmmac: dwmac-mediatek: add platform level clocks management
This patch implements clks_config callback for dwmac-mediatek platform, which could support platform level clocks management.
--- .../ethernet/stmicro/stmmac/dwmac-mediatek.c | 25 +++++++++++++------ 1 file changed, 18 insertions(+), 7 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c +18 -7
@@ -9,7 +9,6 @@#include <linux/of.h> #include <linux/of_device.h> #include <linux/of_net.h> -#include <linux/pm_runtime.h> #include <linux/regmap.h> #include <linux/stmmac.h>
@@ -359,9 +358,6 @@ static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)return ret; } -pm_runtime_enable (&pdev->dev); -pm_runtime_get_sync (&pdev->dev); -return 0 ; }
@@ -370,11 +366,25 @@ static void mediatek_dwmac_exit(struct platform_device *pdev, void *priv)struct mediatek_dwmac_plat_data *plat = priv;clk_bulk_disable_unprepare (plat->num_clks_to_config, plat->clks); - -pm_runtime_put_sync (&pdev->dev); -pm_runtime_disable (&pdev->dev); } +static int mediatek_dwmac_clks_config (void *priv,bool enabled) +{ +struct mediatek_dwmac_plat_data *plat = priv; +int ret =0 ; + +if (enabled) { + ret =clk_bulk_prepare_enable (plat->num_clks_to_config, plat->clks); +if (ret) { +dev_err (plat->dev,"failed to enable clks, err = %d\n" , ret); +return ret; + } + }else { +clk_bulk_disable_unprepare (plat->num_clks_to_config, plat->clks); + } + +return ret; +}static int mediatek_dwmac_probe (struct platform_device *pdev) {struct mediatek_dwmac_plat_data *priv_plat;
@@ -420,6 +430,7 @@ static int mediatek_dwmac_probe(struct platform_device *pdev) plat_dat->bsp_priv = priv_plat; plat_dat->init = mediatek_dwmac_init; plat_dat->exit = mediatek_dwmac_exit; + plat_dat->clks_config = mediatek_dwmac_clks_config;mediatek_dwmac_init (pdev, priv_plat); ret =stmmac_dvr_probe (&pdev->dev, plat_dat, &stmmac_res);
Signature · 1 line
2.25.1
PATCH v8 2/6 stmmac: dwmac-mediatek: Reuse more common features
In reply to Biao HuangThis patch makes dwmac-mediatek reuse more features supported by stmmac_platform.c.
--- .../ethernet/stmicro/stmmac/dwmac-mediatek.c | 32 +++++++++---------- 1 file changed, 15 insertions(+), 17 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c +15 -17
@@ -334,22 +334,20 @@ static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)const struct mediatek_dwmac_variant *variant = plat->variant;int ret; - ret =dma_set_mask_and_coherent (plat->dev,DMA_BIT_MASK (variant->dma_bit_mask)); -if (ret) { -dev_err (plat->dev,"No suitable DMA available, err = %d\n" , ret); -return ret; - } - - ret = variant->dwmac_set_phy_interface (plat); -if (ret) { -dev_err (plat->dev,"failed to set phy interface, err = %d\n" , ret); -return ret; +if (variant->dwmac_set_phy_interface) { + ret = variant->dwmac_set_phy_interface (plat); +if (ret) { +dev_err (plat->dev,"failed to set phy interface, err = %d\n" , ret); +return ret; + } } - ret = variant->dwmac_set_delay (plat); -if (ret) { -dev_err (plat->dev,"failed to set delay value, err = %d\n" , ret); -return ret; +if (variant->dwmac_set_delay) { + ret = variant->dwmac_set_delay (plat); +if (ret) { +dev_err (plat->dev,"failed to set delay value, err = %d\n" , ret); +return ret; + } } ret =clk_bulk_prepare_enable (plat->num_clks_to_config, plat->clks);
@@ -422,15 +420,15 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)return PTR_ERR (plat_dat); plat_dat->interface = priv_plat->phy_mode; - plat_dat->has_gmac4 =1 ; - plat_dat->has_gmac =0 ; - plat_dat->pmt =0 ; + plat_dat->use_phy_wol =1 ; plat_dat->riwt_off =1 ; plat_dat->maxmtu =ETH_DATA_LEN ; + plat_dat->addr64 = priv_plat->variant->dma_bit_mask; plat_dat->bsp_priv = priv_plat; plat_dat->init = mediatek_dwmac_init; plat_dat->exit = mediatek_dwmac_exit; plat_dat->clks_config = mediatek_dwmac_clks_config; +mediatek_dwmac_init (pdev, priv_plat); ret =stmmac_dvr_probe (&pdev->dev, plat_dat, &stmmac_res);
Signature · 1 line
2.25.1
PATCH v8 3/6 arm64: dts: mt2712: update ethernet device node
In reply to Biao HuangSince there are some changes in ethernet driver, update ethernet device node in dts to accommodate to it.
--- arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 1 + arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 14 +++++++++----- 2 files changed, 10 insertions(+), 5 deletions(-)
arch/arm64/boot/dts/mediatek/mt2712-evb.dts +1 -0
@@ -110,6 +110,7 @@ ð { phy-handle = <ðernet_phy0>; mediatek,tx-delay-ps = <1530>; snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; + snps,reset-delays-us = <0 10000 10000>; pinctrl-names = "default", "sleep"; pinctrl-0 = <ð_default>; pinctrl-1 = <ð_sleep>;
arch/arm64/boot/dts/mediatek/mt2712e.dtsi +9 -5
@@ -726,7 +726,7 @@ queue2 { }; eth: ethernet@1101c000 { - compatible = "mediatek,mt2712-gmac"; + compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a"; reg = <0 0x1101c000 0 0x1300>; interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; interrupt-names = "macirq";
@@ -734,15 +734,19 @@ eth: ethernet@1101c000 { clock-names = "axi", "apb", "mac_main", - "ptp_ref"; + "ptp_ref", + "rmii_internal"; clocks = <&pericfg CLK_PERI_GMAC>, <&pericfg CLK_PERI_GMAC_PCLK>, <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, - <&topckgen CLK_TOP_APLL1_D3>; + <&topckgen CLK_TOP_APLL1_D3>, + <&topckgen CLK_TOP_ETHERPLL_50M>; power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; mediatek,pericfg = <&pericfg>; snps,axi-config = <&stmmac_axi_setup>;
Signature · 1 line
2.25.1
Matthias Brugger
maintainerRe: [PATCH net-next v8 3/6] arm64: dts: mt2712: update ethernet device node
Quoted 3 lines · Biao Huang
Since there are some changes in ethernet driver, update ethernet device node in dts to accommodate to it.
I have a hard time to understand how the first two patches are related to this one. Please be more specific in your commit message.
Also please beware that we should make sure that a newer driver version should still work properly with an older device tree, which does not have your changes.
Regards,
Matthias
Quoted 56 lines
Signed-off-by Biao Huang <[email protected]>--- arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 1 + arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 14 +++++++++----- 2 files changed, 10 insertions(+), 5 deletions(-)arch/arm64/boot/dts/mediatek/mt2712-evb.dts +1
-0@@ -110,6 +110,7 @@ ð { phy-handle = <ðernet_phy0>; mediatek,tx-delay-ps = <1530>; snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; + snps,reset-delays-us = <0 10000 10000>; pinctrl-names = "default", "sleep"; pinctrl-0 = <ð_default>; pinctrl-1 = <ð_sleep>;arch/arm64/boot/dts/mediatek/mt2712e.dtsi +9
-5@@ -726,7 +726,7 @@ queue2 { }; eth: ethernet@1101c000 { - compatible = "mediatek,mt2712-gmac"; + compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a"; reg = <0 0x1101c000 0 0x1300>; interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; interrupt-names = "macirq";@@ -734,15 +734,19 @@ eth: ethernet@1101c000 { clock-names = "axi", "apb", "mac_main", - "ptp_ref"; + "ptp_ref", + "rmii_internal"; clocks = <&pericfg CLK_PERI_GMAC>, <&pericfg CLK_PERI_GMAC_PCLK>, <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, - <&topckgen CLK_TOP_APLL1_D3>; + <&topckgen CLK_TOP_APLL1_D3>, + <&topckgen CLK_TOP_ETHERPLL_50M>; power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; mediatek,pericfg = <&pericfg>; snps,axi-config = <&stmmac_axi_setup>;
Re: [PATCH net-next v8 3/6] arm64: dts: mt2712: update ethernet device node
Dear Matthias,
Thanks for your comments~
Quoted 9 lines · Matthias Brugger
Quoted 3 lines · Biao Huang
Since there are some changes in ethernet driver, update ethernet device node in dts to accommodate to it.
I have a hard time to understand how the first two patches are related to this
one. Please be more specific in your commit message.
This dts patch is not related to previous two patches in this series.
Actually, this patch should be sent with commit "71a55a2315b047352b3d65e2d24724207be85ae2", which added extra RMII support in driver. But unfortunately, we missed it out.
Is there any proper way to relate this patch to commit "71a55a2315b047352b3d65e2d24724207be85ae2"? (Fixed tag seems not a good choice, or just add more details in commit message?)
Quoted 71 lines
Also please beware that we should make sure that a newer driver version should
still work properly with an older device tree, which does not have your changes.Regards,
MatthiasQuoted 62 lines
Signed-off-by Biao Huang <[email protected]>--- arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 1 + arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 14 +++++++++----- 2 files changed, 10 insertions(+), 5 deletions(-)arch/arm64/boot/dts/mediatek/mt2712-evb.dts +1
-0@@ -110,6 +110,7 @@ ð { phy-handle = <ðernet_phy0>; mediatek,tx-delay-ps = <1530>; snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; + snps,reset-delays-us = <0 10000 10000>; pinctrl-names = "default", "sleep"; pinctrl-0 = <ð_default>; pinctrl-1 = <ð_sleep>;arch/arm64/boot/dts/mediatek/mt2712e.dtsi +1
-1@@ -726,7 +726,7 @@ queue2 { }; eth: ethernet@1101c000 { - compatible = "mediatek,mt2712-gmac"; + compatible = "mediatek,mt2712-gmac", "snps,dwmac- 4.20a"; reg = <0 0x1101c000 0 0x1300>; interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;interrupt-names = "macirq";arch/arm64/boot/dts/mediatek/mt2712e.dtsi +8
-4@@ -734,15 +734,19 @@ eth: ethernet@1101c000 { clock-names = "axi", "apb", "mac_main", - "ptp_ref"; + "ptp_ref", + "rmii_internal"; clocks = <&pericfg CLK_PERI_GMAC>, <&pericfg CLK_PERI_GMAC_PCLK>, <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, - <&topckgen CLK_TOP_APLL1_D3>; + <&topckgen CLK_TOP_APLL1_D3>, + <&topckgen CLK_TOP_ETHERPLL_50M>;power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; mediatek,pericfg = <&pericfg>; snps,axi-config = <&stmmac_axi_setup>;
Matthias Brugger
maintainerRe: [PATCH net-next v8 3/6] arm64: dts: mt2712: update ethernet device node
In reply to Biao HuangQuoted 3 lines · Biao Huang
Since there are some changes in ethernet driver, update ethernet device node in dts to accommodate to it.
I have a hard time to understand how the changes in 1/6 and 2/6 are related to that.
Please explain better what has changed. Also beware that we shouldn't introduce any non-backward compatible DTS changes. That means, the device should work with the new driver but an older device tree.
Regards,
Matthias
Quoted 56 lines
Signed-off-by Biao Huang <[email protected]>--- arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 1 + arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 14 +++++++++----- 2 files changed, 10 insertions(+), 5 deletions(-)arch/arm64/boot/dts/mediatek/mt2712-evb.dts +1
-0@@ -110,6 +110,7 @@ ð { phy-handle = <ðernet_phy0>; mediatek,tx-delay-ps = <1530>; snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; + snps,reset-delays-us = <0 10000 10000>; pinctrl-names = "default", "sleep"; pinctrl-0 = <ð_default>; pinctrl-1 = <ð_sleep>;arch/arm64/boot/dts/mediatek/mt2712e.dtsi +9
-5@@ -726,7 +726,7 @@ queue2 { }; eth: ethernet@1101c000 { - compatible = "mediatek,mt2712-gmac"; + compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a"; reg = <0 0x1101c000 0 0x1300>; interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; interrupt-names = "macirq";@@ -734,15 +734,19 @@ eth: ethernet@1101c000 { clock-names = "axi", "apb", "mac_main", - "ptp_ref"; + "ptp_ref", + "rmii_internal"; clocks = <&pericfg CLK_PERI_GMAC>, <&pericfg CLK_PERI_GMAC_PCLK>, <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, - <&topckgen CLK_TOP_APLL1_D3>; + <&topckgen CLK_TOP_APLL1_D3>, + <&topckgen CLK_TOP_ETHERPLL_50M>; power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; mediatek,pericfg = <&pericfg>; snps,axi-config = <&stmmac_axi_setup>;
Re: [PATCH net-next v8 3/6] arm64: dts: mt2712: update ethernet device node
Dear Matthias,
Thanks for your comments~
Quoted 10 lines · Matthias Brugger
Quoted 3 lines · Biao Huang
Since there are some changes in ethernet driver, update ethernet device node in dts to accommodate to it.
I have a hard time to understand how the changes in 1/6 and 2/6 are related to
that.
Quoted 9 lines
Please explain better what has changed. Also beware that we shouldn't introduce
any non-backward compatible DTS changes. That means, the device should work with
the new driver but an older device tree.Regards,
Matthias
http://lists.infradead.org/pipermail/linux-mediatek/2021-December/032812.html
I've add more details to commit message in v10 send, please kindly review it.
Regards!
Biao
Quoted 62 lines
Quoted 62 lines
Signed-off-by Biao Huang <[email protected]>--- arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 1 + arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 14 +++++++++----- 2 files changed, 10 insertions(+), 5 deletions(-)arch/arm64/boot/dts/mediatek/mt2712-evb.dts +1
-0@@ -110,6 +110,7 @@ ð { phy-handle = <ðernet_phy0>; mediatek,tx-delay-ps = <1530>; snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; + snps,reset-delays-us = <0 10000 10000>; pinctrl-names = "default", "sleep"; pinctrl-0 = <ð_default>; pinctrl-1 = <ð_sleep>;arch/arm64/boot/dts/mediatek/mt2712e.dtsi +1
-1@@ -726,7 +726,7 @@ queue2 { }; eth: ethernet@1101c000 { - compatible = "mediatek,mt2712-gmac"; + compatible = "mediatek,mt2712-gmac", "snps,dwmac- 4.20a"; reg = <0 0x1101c000 0 0x1300>; interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;interrupt-names = "macirq";arch/arm64/boot/dts/mediatek/mt2712e.dtsi +8
-4@@ -734,15 +734,19 @@ eth: ethernet@1101c000 { clock-names = "axi", "apb", "mac_main", - "ptp_ref"; + "ptp_ref", + "rmii_internal"; clocks = <&pericfg CLK_PERI_GMAC>, <&pericfg CLK_PERI_GMAC_PCLK>, <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, - <&topckgen CLK_TOP_APLL1_D3>; + <&topckgen CLK_TOP_APLL1_D3>, + <&topckgen CLK_TOP_ETHERPLL_50M>;power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; mediatek,pericfg = <&pericfg>; snps,axi-config = <&stmmac_axi_setup>;
PATCH v8 4/6 net: dt-bindings: dwmac: Convert mediatek-dwmac to DT schema
In reply to Biao HuangConvert mediatek-dwmac to DT schema, and delete old mediatek-dwmac.txt. And there are some changes in .yaml than .txt, others almost keep the same:
1. compatible "const: snps,dwmac-4.20".
2. delete "snps,reset-active-low;" in example, since driver remove this property long ago.
3. add "snps,reset-delay-us = <0 10000 10000>" in example.
4. the example is for rgmii interface, keep related properties only.
--- .../bindings/net/mediatek-dwmac.txt | 91 ---------- .../bindings/net/mediatek-dwmac.yaml | 156 ++++++++++++++++++ 2 files changed, 156 insertions(+), 91 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.txt create mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0 -91
@@ -1,91 +0,0 @@ -MediaTek DWMAC glue layer controller - -This file documents platform glue layer for stmmac. -Please see stmmac.txt for the other unchanged properties. - -The device node has following properties. - -Required properties: -- compatible: Should be "mediatek,mt2712-gmac" for MT2712 SoC -- reg: Address and length of the register set for the device -- interrupts: Should contain the MAC interrupts -- interrupt-names: Should contain a list of interrupt names corresponding to - the interrupts in the interrupts property, if available. - Should be "macirq" for the main MAC IRQ -- clocks: Must contain a phandle for each entry in clock-names. -- clock-names: The name of the clock listed in the clocks property. These are - "axi", "apb", "mac_main", "ptp_ref", "rmii_internal" for MT2712 SoC. -- mac-address: See ethernet.txt in the same directory -- phy-mode: See ethernet.txt in the same directory -- mediatek,pericfg: A phandle to the syscon node that control ethernet - interface and timing delay. - -Optional properties: -- mediatek,tx-delay-ps: TX clock delay macro value. Default is 0. - It should be defined for RGMII/MII interface. - It should be defined for RMII interface when the reference clock is from MT2712 SoC. -- mediatek,rx-delay-ps: RX clock delay macro value. Default is 0. - It should be defined for RGMII/MII interface. - It should be defined for RMII interface. -Both delay properties need to be a multiple of 170 for RGMII interface, -or will round down. Range 0~31*170. -Both delay properties need to be a multiple of 550 for MII/RMII interface, -or will round down. Range 0~31*550. - -- mediatek,rmii-rxc: boolean property, if present indicates that the RMII - reference clock, which is from external PHYs, is connected to RXC pin - on MT2712 SoC. - Otherwise, is connected to TXC pin. -- mediatek,rmii-clk-from-mac: boolean property, if present indicates that - MT2712 SoC provides the RMII reference clock, which outputs to TXC pin only. -- mediatek,txc-inverse: boolean property, if present indicates that - 1. tx clock will be inversed in MII/RGMII case, - 2. tx clock inside MAC will be inversed relative to reference clock - which is from external PHYs in RMII case, and it rarely happen. - 3. the reference clock, which outputs to TXC pin will be inversed in RMII case - when the reference clock is from MT2712 SoC. -- mediatek,rxc-inverse: boolean property, if present indicates that - 1. rx clock will be inversed in MII/RGMII case. - 2. reference clock will be inversed when arrived at MAC in RMII case, when - the reference clock is from external PHYs. - 3. the inside clock, which be sent to MAC, will be inversed in RMII case when - the reference clock is from MT2712 SoC. -- assigned-clocks: mac_main and ptp_ref clocks -- assigned-clock-parents: parent clocks of the assigned clocks - -Example: - eth: ethernet@1101c000 { - compatible = "mediatek,mt2712-gmac"; - reg = <0 0x1101c000 0 0x1300>; - interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; - interrupt-names = "macirq"; - phy-mode ="rgmii-rxid"; - mac-address = [00 55 7b b5 7d f7]; - clock-names = "axi", - "apb", - "mac_main", - "ptp_ref", - "rmii_internal"; - clocks = <&pericfg CLK_PERI_GMAC>, - <&pericfg CLK_PERI_GMAC_PCLK>, - <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; - assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, - <&topckgen CLK_TOP_APLL1_D3>, - <&topckgen CLK_TOP_ETHERPLL_50M>; - power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; - mediatek,pericfg = <&pericfg>; - mediatek,tx-delay-ps = <1530>; - mediatek,rx-delay-ps = <1530>; - mediatek,rmii-rxc; - mediatek,txc-inverse; - mediatek,rxc-inverse; - snps,txpbl = <1>; - snps,rxpbl = <1>; - snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; - snps,reset-active-low; - };
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +156 -0
156 lines not on this page · raw message
Signature · 1 line
2.25.1
Rob Herring
maintainerRe: [PATCH net-next v8 4/6] net: dt-bindings: dwmac: Convert mediatek-dwmac to DT schema
Quoted 8 lines · Biao Huang
Convert mediatek-dwmac to DT schema, and delete old mediatek-dwmac.txt. And there are some changes in .yaml than .txt, others almost keep the same:
1. compatible "const: snps,dwmac-4.20".
2. delete "snps,reset-active-low;" in example, since driver remove this property long ago.
3. add "snps,reset-delay-us = <0 10000 10000>" in example.
4. the example is for rgmii interface, keep related properties only.
Quoted 8 lines
Signed-off-by Biao Huang <[email protected]>--- .../bindings/net/mediatek-dwmac.txt | 91 ---------- .../bindings/net/mediatek-dwmac.yaml | 156 ++++++++++++++++++ 2 files changed, 156 insertions(+), 91 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.txt create mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
Running 'make dtbs_check' with the schema in this patch gives the following warnings. Consider if they are expected or the schema is incorrect. These may not be new warnings.
Note that it is not yet a requirement to have 0 warnings for dtbs_check. This will change in the future.
Full log is available here: https://patchwork.ozlabs.org/patch/1566169
ethernet@1101c000: clock-names: ['axi', 'apb', 'mac_main', 'ptp_ref'] is too short
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: clocks: [[27, 34], [27, 37], [6, 154], [6, 155]] is too short
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: compatible: ['mediatek,mt2712-gmac'] does not contain items matching the given schema
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: compatible: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: Unevaluated properties are not allowed ('compatible', 'reg', 'interrupts', 'interrupt-names', 'mac-address', 'clock-names', 'clocks', 'power-domains', 'snps,axi-config', 'snps,mtl-rx-config', 'snps,mtl-tx-config', 'snps,txpbl', 'snps,rxpbl', 'clk_csr', 'phy-mode', 'phy-handle', 'snps,reset-gpio', 'mdio' were unexpected)
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
Rob Herring
maintainerRe: [PATCH net-next v8 4/6] net: dt-bindings: dwmac: Convert mediatek-dwmac to DT schema
In reply to Biao HuangQuoted 140 lines · Biao Huang
Convert mediatek-dwmac to DT schema, and delete old mediatek-dwmac.txt. And there are some changes in .yaml than .txt, others almost keep the same:
1. compatible "const: snps,dwmac-4.20".
2. delete "snps,reset-active-low;" in example, since driver remove this property long ago.
3. add "snps,reset-delay-us = <0 10000 10000>" in example.
4. the example is for rgmii interface, keep related properties only.Signed-off-by Biao Huang <[email protected]>--- .../bindings/net/mediatek-dwmac.txt | 91 ---------- .../bindings/net/mediatek-dwmac.yaml | 156 ++++++++++++++++++ 2 files changed, 156 insertions(+), 91 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.txt create mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.yamlDocumentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-91@@ -1,91 +0,0 @@ -MediaTek DWMAC glue layer controller - -This file documents platform glue layer for stmmac. -Please see stmmac.txt for the other unchanged properties. - -The device node has following properties. - -Required properties: -- compatible: Should be "mediatek,mt2712-gmac" for MT2712 SoC -- reg: Address and length of the register set for the device -- interrupts: Should contain the MAC interrupts -- interrupt-names: Should contain a list of interrupt names corresponding to - the interrupts in the interrupts property, if available. - Should be "macirq" for the main MAC IRQ -- clocks: Must contain a phandle for each entry in clock-names. -- clock-names: The name of the clock listed in the clocks property. These are - "axi", "apb", "mac_main", "ptp_ref", "rmii_internal" for MT2712 SoC. -- mac-address: See ethernet.txt in the same directory -- phy-mode: See ethernet.txt in the same directory -- mediatek,pericfg: A phandle to the syscon node that control ethernet - interface and timing delay. - -Optional properties: -- mediatek,tx-delay-ps: TX clock delay macro value. Default is 0. - It should be defined for RGMII/MII interface. - It should be defined for RMII interface when the reference clock is from MT2712 SoC. -- mediatek,rx-delay-ps: RX clock delay macro value. Default is 0. - It should be defined for RGMII/MII interface. - It should be defined for RMII interface. -Both delay properties need to be a multiple of 170 for RGMII interface, -or will round down. Range 0~31*170. -Both delay properties need to be a multiple of 550 for MII/RMII interface, -or will round down. Range 0~31*550. - -- mediatek,rmii-rxc: boolean property, if present indicates that the RMII - reference clock, which is from external PHYs, is connected to RXC pin - on MT2712 SoC. - Otherwise, is connected to TXC pin. -- mediatek,rmii-clk-from-mac: boolean property, if present indicates that - MT2712 SoC provides the RMII reference clock, which outputs to TXC pin only. -- mediatek,txc-inverse: boolean property, if present indicates that - 1. tx clock will be inversed in MII/RGMII case, - 2. tx clock inside MAC will be inversed relative to reference clock - which is from external PHYs in RMII case, and it rarely happen. - 3. the reference clock, which outputs to TXC pin will be inversed in RMII case - when the reference clock is from MT2712 SoC. -- mediatek,rxc-inverse: boolean property, if present indicates that - 1. rx clock will be inversed in MII/RGMII case. - 2. reference clock will be inversed when arrived at MAC in RMII case, when - the reference clock is from external PHYs. - 3. the inside clock, which be sent to MAC, will be inversed in RMII case when - the reference clock is from MT2712 SoC. -- assigned-clocks: mac_main and ptp_ref clocks -- assigned-clock-parents: parent clocks of the assigned clocks - -Example: - eth: ethernet@1101c000 { - compatible = "mediatek,mt2712-gmac"; - reg = <0 0x1101c000 0 0x1300>; - interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; - interrupt-names = "macirq"; - phy-mode ="rgmii-rxid"; - mac-address = [00 55 7b b5 7d f7]; - clock-names = "axi", - "apb", - "mac_main", - "ptp_ref", - "rmii_internal"; - clocks = <&pericfg CLK_PERI_GMAC>, - <&pericfg CLK_PERI_GMAC_PCLK>, - <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; - assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, - <&topckgen CLK_TOP_APLL1_D3>, - <&topckgen CLK_TOP_ETHERPLL_50M>; - power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; - mediatek,pericfg = <&pericfg>; - mediatek,tx-delay-ps = <1530>; - mediatek,rx-delay-ps = <1530>; - mediatek,rmii-rxc; - mediatek,txc-inverse; - mediatek,rxc-inverse; - snps,txpbl = <1>; - snps,rxpbl = <1>; - snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; - snps,reset-active-low; - };Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +21
-0@@ -0,0 +1,156 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/mediatek-dwmac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek DWMAC glue layer controller + +maintainers: + - Biao Huang <[email protected]> + +description: + This file documents platform glue layer for stmmac. + +# We need a select here so we don't match all nodes with 'snps,dwmac' +select: + properties: + compatible: + contains: + enum: + - mediatek,mt2712-gmac
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml line 31
Quoted 10 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +10
-0+ required: + - compatible + +allOf: + - $ref: "snps,dwmac.yaml#" + +properties: + compatible: + oneOf: + - items:
Don't need oneOf for 1 entry.
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml line 42
Quoted 11 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +11
-0+ - enum: + - mediatek,mt2712-gmac + - const: snps,dwmac-4.20a + + clocks: + items: + - description: AXI clock + - description: APB clock + - description: MAC Main clock + - description: PTP clock + - description: RMII reference clock provided by MAC
Seems you need 'minItems: 4' or are the DT files wrong?
Quoted 118 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +114
-0+ + clock-names: + items: + - const: axi + - const: apb + - const: mac_main + - const: ptp_ref + - const: rmii_internal + + mediatek,pericfg: + $ref: /schemas/types.yaml#/definitions/phandle + description: + The phandle to the syscon node that control ethernet + interface and timing delay. + + mediatek,tx-delay-ps: + description: + The internal TX clock delay (provided by this driver) in nanoseconds. + For MT2712 RGMII interface, Allowed value need to be a multiple of 170, + or will round down. Range 0~31*170. + For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, + or will round down. Range 0~31*550. + + mediatek,rx-delay-ps: + description: + The internal RX clock delay (provided by this driver) in nanoseconds. + For MT2712 RGMII interface, Allowed value need to be a multiple of 170, + or will round down. Range 0~31*170. + For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, + or will round down. Range 0~31*550. + + mediatek,rmii-rxc: + type: boolean + description: + If present, indicates that the RMII reference clock, which is from external + PHYs, is connected to RXC pin. Otherwise, is connected to TXC pin. + + mediatek,rmii-clk-from-mac: + type: boolean + description: + If present, indicates that MAC provides the RMII reference clock, which + outputs to TXC pin only. + + mediatek,txc-inverse: + type: boolean + description: + If present, indicates that + 1. tx clock will be inversed in MII/RGMII case, + 2. tx clock inside MAC will be inversed relative to reference clock + which is from external PHYs in RMII case, and it rarely happen. + 3. the reference clock, which outputs to TXC pin will be inversed in RMII case + when the reference clock is from MAC. + + mediatek,rxc-inverse: + type: boolean + description: + If present, indicates that + 1. rx clock will be inversed in MII/RGMII case. + 2. reference clock will be inversed when arrived at MAC in RMII case, when + the reference clock is from external PHYs. + 3. the inside clock, which be sent to MAC, will be inversed in RMII case when + the reference clock is from MAC. + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + - phy-mode + - mediatek,pericfg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/mt2712-clk.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/mt2712-power.h> + + eth: ethernet@1101c000 { + compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a"; + reg = <0x1101c000 0x1300>; + interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "macirq"; + phy-mode ="rgmii-rxid"; + mac-address = [00 55 7b b5 7d f7]; + clock-names = "axi", + "apb", + "mac_main", + "ptp_ref", + "rmii_internal"; + clocks = <&pericfg CLK_PERI_GMAC>, + <&pericfg CLK_PERI_GMAC_PCLK>, + <&topckgen CLK_TOP_ETHER_125M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; + assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, + <&topckgen CLK_TOP_APLL1_D3>, + <&topckgen CLK_TOP_ETHERPLL_50M>; + power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; + mediatek,pericfg = <&pericfg>; + mediatek,tx-delay-ps = <1530>; + snps,txpbl = <1>; + snps,rxpbl = <1>; + snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; + snps,reset-delays-us = <0 10000 10000>; + };Signature · 1 line
2.25.1
Re: [PATCH net-next v8 4/6] net: dt-bindings: dwmac: Convert mediatek-dwmac to DT schema
Dear Rob,
Thanks for your comments~
Quoted 178 lines · Rob Herring
Quoted 177 lines · Biao Huang
Convert mediatek-dwmac to DT schema, and delete old mediatek- dwmac.txt.
And there are some changes in .yaml than .txt, others almost keep the same:
1. compatible "const: snps,dwmac-4.20".
2. delete "snps,reset-active-low;" in example, since driver
remove this
property long ago.
3. add "snps,reset-delay-us = <0 10000 10000>" in example.
4. the example is for rgmii interface, keep related properties
only.Signed-off-by Biao Huang <[email protected]>--- .../bindings/net/mediatek-dwmac.txt | 91 ---------- .../bindings/net/mediatek-dwmac.yaml | 156 ++++++++++++++++++ 2 files changed, 156 insertions(+), 91 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/mediatek- dwmac.txt create mode 100644 Documentation/devicetree/bindings/net/mediatek-
dwmac.yaml(quoted diff) +0
-0dwmac.txt b/Documentation/devicetree/bindings/net/mediatek- dwmac.txt
deleted file mode 100644
index afbcaebf062e..000000000000Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-12@@ -1,91 +0,0 @@ -MediaTek DWMAC glue layer controller - -This file documents platform glue layer for stmmac. -Please see stmmac.txt for the other unchanged properties. - -The device node has following properties. - -Required properties: -- compatible: Should be "mediatek,mt2712-gmac" for MT2712 SoC -- reg: Address and length of the register set for the device -- interrupts: Should contain the MAC interrupts -- interrupt-names: Should contain a list of interrupt namescorresponding to
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-4- the interrupts in the interrupts property, if available. - Should be "macirq" for the main MAC IRQ -- clocks: Must contain a phandle for each entry in clock-names. -- clock-names: The name of the clock listed in the clocksproperty. These are
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-1- "axi", "apb", "mac_main", "ptp_ref", "rmii_internal" for MT2712SoC.
-- mac-address: See ethernet.txt in the same directory -- phy-mode: See ethernet.txt in the same directory -- mediatek,pericfg: A phandle to the syscon node that control ethernetDocumentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-6- interface and timing delay. - -Optional properties: -- mediatek,tx-delay-ps: TX clock delay macro value. Default is 0. - It should be defined for RGMII/MII interface. - It should be defined for RMII interface when the referenceclock is from MT2712 SoC.
-- mediatek,rx-delay-ps: RX clock delay macro value. Default is 0.Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-3- It should be defined for RGMII/MII interface. - It should be defined for RMII interface. -Both delay properties need to be a multiple of 170 for RGMIIinterface,
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-2-or will round down. Range 0~31*170. -Both delay properties need to be a multiple of 550 for MII/RMIIinterface,
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-3-or will round down. Range 0~31*550. - -- mediatek,rmii-rxc: boolean property, if present indicates thatthe RMII
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-1- reference clock, which is from external PHYs, is connected toRXC pin
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-3- on MT2712 SoC. - Otherwise, is connected to TXC pin. -- mediatek,rmii-clk-from-mac: boolean property, if presentindicates that
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-1- MT2712 SoC provides the RMII reference clock, which outputs toTXC pin only.
-- mediatek,txc-inverse: boolean property, if present indicates thatDocumentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-2- 1. tx clock will be inversed in MII/RGMII case, - 2. tx clock inside MAC will be inversed relative to referenceclock
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-1- which is from external PHYs in RMII case, and it rarelyhappen.
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-1- 3. the reference clock, which outputs to TXC pin will beinversed in RMII case
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-2- when the reference clock is from MT2712 SoC. -- mediatek,rxc-inverse: boolean property, if present indicatesthat
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-2- 1. rx clock will be inversed in MII/RGMII case. - 2. reference clock will be inversed when arrived at MAC in RMIIcase, when
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-2- the reference clock is from external PHYs. - 3. the inside clock, which be sent to MAC, will be inversed inRMII case when
Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-25- the reference clock is from MT2712 SoC. -- assigned-clocks: mac_main and ptp_ref clocks -- assigned-clock-parents: parent clocks of the assigned clocks - -Example: - eth: ethernet@1101c000 { - compatible = "mediatek,mt2712-gmac"; - reg = <0 0x1101c000 0 0x1300>; - interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; - interrupt-names = "macirq"; - phy-mode ="rgmii-rxid"; - mac-address = [00 55 7b b5 7d f7]; - clock-names = "axi", - "apb", - "mac_main", - "ptp_ref", - "rmii_internal"; - clocks = <&pericfg CLK_PERI_GMAC>, - <&pericfg CLK_PERI_GMAC_PCLK>, - <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; - assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>, - <&topckgen
CLK_TOP_ETHER_50M_RMII_SEL>;Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-1- assigned-clock-parents = <&topckgen
CLK_TOP_ETHERPLL_125M>,Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-2- <&topckgen CLK_TOP_APLL1_D3>, - <&topckgen
CLK_TOP_ETHERPLL_50M>;Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted +0
-12- power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; - mediatek,pericfg = <&pericfg>; - mediatek,tx-delay-ps = <1530>; - mediatek,rx-delay-ps = <1530>; - mediatek,rmii-rxc; - mediatek,txc-inverse; - mediatek,rxc-inverse; - snps,txpbl = <1>; - snps,rxpbl = <1>; - snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; - snps,reset-active-low; - };(quoted diff) +0
-0
dwmac.yamlb/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
new file mode 100644
index 000000000000..9207266a6e69Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +15
-0@@ -0,0 +1,156 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/mediatek-dwmac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek DWMAC glue layer controller + +maintainers: + - Biao Huang <[email protected]> + +description: + This file documents platform glue layer for stmmac. + +# We need a select here so we don't match all nodes with'snps,dwmac'
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +10
-0+select: + properties: + compatible: + contains: + enum: + - mediatek,mt2712-gmac + required: + - compatible + +allOf:
Quoted 8 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml line 31
Quoted 6 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +6
-0+ - $ref: "snps,dwmac.yaml#" + +properties: + compatible: + oneOf: + - items:Don't need oneOf for 1 entry.
OK, I'll fix it in next send.
Quoted 13 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml line 42
Quoted 12 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +11
-0+ - enum: + - mediatek,mt2712-gmac + - const: snps,dwmac-4.20a + + clocks: + items: + - description: AXI clock + - description: APB clock + - description: MAC Main clock + - description: PTP clock + - description: RMII reference clock provided by MAC
Quoted 1 line
Seems you need 'minItems: 4' or are the DT files wrong?
The current eth device node in mt2712.dtsi should be updated, and there is a patch in this series for it:
"[PATCH net-next v8 3/6] arm64: dts: mt2712: update ethernet device node"
Quoted 134 lines
Quoted 134 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +18
-0+ + clock-names: + items: + - const: axi + - const: apb + - const: mac_main + - const: ptp_ref + - const: rmii_internal + + mediatek,pericfg: + $ref: /schemas/types.yaml#/definitions/phandle + description: + The phandle to the syscon node that control ethernet + interface and timing delay. + + mediatek,tx-delay-ps: + description: + The internal TX clock delay (provided by this driver) innanoseconds.
+ For MT2712 RGMII interface, Allowed value need to be a
multiple of 170,Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +2
-0+ or will round down. Range 0~31*170. + For MT2712 RMII/MII interface, Allowed value need to be amultiple of 550,
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +5
-0+ or will round down. Range 0~31*550. + + mediatek,rx-delay-ps: + description: + The internal RX clock delay (provided by this driver) innanoseconds.
+ For MT2712 RGMII interface, Allowed value need to be a
multiple of 170,Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +2
-0+ or will round down. Range 0~31*170. + For MT2712 RMII/MII interface, Allowed value need to be amultiple of 550,
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +6
-0+ or will round down. Range 0~31*550. + + mediatek,rmii-rxc: + type: boolean + description: + If present, indicates that the RMII reference clock, whichis from external
+ PHYs, is connected to RXC pin. Otherwise, is connected to
TXC pin.Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +5
-0+ + mediatek,rmii-clk-from-mac: + type: boolean + description: + If present, indicates that MAC provides the RMII referenceclock, which
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +8
-0+ outputs to TXC pin only. + + mediatek,txc-inverse: + type: boolean + description: + If present, indicates that + 1. tx clock will be inversed in MII/RGMII case, + 2. tx clock inside MAC will be inversed relative toreference clock
+ which is from external PHYs in RMII case, and it rarely
happen.
+ 3. the reference clock, which outputs to TXC pin will be
inversed in RMII caseDocumentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +8
-0+ when the reference clock is from MAC. + + mediatek,rxc-inverse: + type: boolean + description: + If present, indicates that + 1. rx clock will be inversed in MII/RGMII case. + 2. reference clock will be inversed when arrived at MAC inRMII case, when
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +2
-0+ the reference clock is from external PHYs. + 3. the inside clock, which be sent to MAC, will be inversedin RMII case when
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +43
-0+ the reference clock is from MAC. + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + - phy-mode + - mediatek,pericfg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/mt2712-clk.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/mt2712-power.h> + + eth: ethernet@1101c000 { + compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a"; + reg = <0x1101c000 0x1300>; + interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "macirq"; + phy-mode ="rgmii-rxid"; + mac-address = [00 55 7b b5 7d f7]; + clock-names = "axi", + "apb", + "mac_main", + "ptp_ref", + "rmii_internal"; + clocks = <&pericfg CLK_PERI_GMAC>, + <&pericfg CLK_PERI_GMAC_PCLK>, + <&topckgen CLK_TOP_ETHER_125M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; + assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; + assigned-clock-parents = <&topckgen
CLK_TOP_ETHERPLL_125M>,Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file +10
-0+ <&topckgen CLK_TOP_APLL1_D3>, + <&topckgen CLK_TOP_ETHERPLL_50M>; + power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; + mediatek,pericfg = <&pericfg>; + mediatek,tx-delay-ps = <1530>; + snps,txpbl = <1>; + snps,rxpbl = <1>; + snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; + snps,reset-delays-us = <0 10000 10000>; + };Signature · 1 line
2.25.1
PATCH v8 5/6 stmmac: dwmac-mediatek: add support for mt8195
In reply to Biao HuangAdd Ethernet support for MediaTek SoCs from the mt8195 family.
--- .../ethernet/stmicro/stmmac/dwmac-mediatek.c | 253 +++++++++++++++++- 1 file changed, 252 insertions(+), 1 deletion(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c +252 -1
@@ -39,6 +39,33 @@#define ETH_FINE_DLY_GTXC BIT(1)#define ETH_FINE_DLY_RXC BIT(0) +/* Peri Configuration register for mt8195 */ +#define MT8195_PERI_ETH_CTRL0 0xFD0 +#define MT8195_RMII_CLK_SRC_INTERNAL BIT(28) +#define MT8195_RMII_CLK_SRC_RXC BIT(27) +#define MT8195_ETH_INTF_SEL GENMASK(26, 24) +#define MT8195_RGMII_TXC_PHASE_CTRL BIT(22) +#define MT8195_EXT_PHY_MODE BIT(21) +#define MT8195_DLY_GTXC_INV BIT(12) +#define MT8195_DLY_GTXC_ENABLE BIT(5) +#define MT8195_DLY_GTXC_STAGES GENMASK(4, 0) + +#define MT8195_PERI_ETH_CTRL1 0xFD4 +#define MT8195_DLY_RXC_INV BIT(25) +#define MT8195_DLY_RXC_ENABLE BIT(18) +#define MT8195_DLY_RXC_STAGES GENMASK(17, 13) +#define MT8195_DLY_TXC_INV BIT(12) +#define MT8195_DLY_TXC_ENABLE BIT(5) +#define MT8195_DLY_TXC_STAGES GENMASK(4, 0) + +#define MT8195_PERI_ETH_CTRL2 0xFD8 +#define MT8195_DLY_RMII_RXC_INV BIT(25) +#define MT8195_DLY_RMII_RXC_ENABLE BIT(18) +#define MT8195_DLY_RMII_RXC_STAGES GENMASK(17, 13) +#define MT8195_DLY_RMII_TXC_INV BIT(12) +#define MT8195_DLY_RMII_TXC_ENABLE BIT(5) +#define MT8195_DLY_RMII_TXC_STAGES GENMASK(4, 0) +struct mac_delay_struct {u32 tx_delay;u32 rx_delay;
@@ -57,11 +84,13 @@ struct mediatek_dwmac_plat_data {int num_clks_to_config;bool rmii_clk_from_mac;bool rmii_rxc; +bool mac_wol; };struct mediatek_dwmac_variant {int (*dwmac_set_phy_interface)(struct mediatek_dwmac_plat_data *plat);int (*dwmac_set_delay)(struct mediatek_dwmac_plat_data *plat); +void (*dwmac_fix_mac_speed)(void *priv,unsigned int speed);/* clock ids to be requested */ const char *const *clk_list;
@@ -77,6 +106,10 @@ static const char * const mt2712_dwmac_clk_l[] = { "axi", "apb", "mac_main", "ptp_ref", "rmii_internal" }; +static const char *const mt8195_dwmac_clk_l[] = { +"axi" ,"apb" ,"mac_cg" ,"mac_main" ,"ptp_ref" ,"rmii_internal" +}; +static int mt2712_set_interface (struct mediatek_dwmac_plat_data *plat) {int rmii_clk_from_mac = plat->rmii_clk_from_mac ?RMII_CLK_SRC_INTERNAL :0 ;
@@ -267,6 +300,204 @@ static const struct mediatek_dwmac_variant mt2712_gmac_variant = { .tx_delay_max = 17600, }; +static int mt8195_set_interface (struct mediatek_dwmac_plat_data *plat) +{ +int rmii_clk_from_mac = plat->rmii_clk_from_mac ?MT8195_RMII_CLK_SRC_INTERNAL :0 ; +int rmii_rxc = plat->rmii_rxc ?MT8195_RMII_CLK_SRC_RXC :0 ; +u32 intf_val =0 ; + +/* The clock labeled as "rmii_internal" in mt8195_dwmac_clk_l is needed +* only in RMII(when MAC provides the reference clock), and useless for +* RGMII/MII/RMII(when PHY provides the reference clock). +* num_clks_to_config indicates the real number of clocks should be +* configured, equals to (plat->variant->num_clks - 1) in default for all the case, +* then +1 for rmii_clk_from_mac case. +*/ + plat->num_clks_to_config = plat->variant->num_clks -1 ; + +/* select phy interface in top control domain */ +switch (plat->phy_mode) { +case PHY_INTERFACE_MODE_MII : + intf_val |=FIELD_PREP (MT8195_ETH_INTF_SEL ,PHY_INTF_MII ); +break ; +case PHY_INTERFACE_MODE_RMII : +if (plat->rmii_clk_from_mac) + plat->num_clks_to_config++; + intf_val |= (rmii_rxc | rmii_clk_from_mac); + intf_val |=FIELD_PREP (MT8195_ETH_INTF_SEL ,PHY_INTF_RMII ); +break ; +case PHY_INTERFACE_MODE_RGMII : +case PHY_INTERFACE_MODE_RGMII_TXID : +case PHY_INTERFACE_MODE_RGMII_RXID : +case PHY_INTERFACE_MODE_RGMII_ID : + intf_val |=FIELD_PREP (MT8195_ETH_INTF_SEL ,PHY_INTF_RGMII ); +break ; +default : +dev_err (plat->dev,"phy interface not supported\n" ); +return -EINVAL ; + } + +/* MT8195 only support external PHY */ + intf_val |=MT8195_EXT_PHY_MODE ; + +regmap_write (plat->peri_regmap,MT8195_PERI_ETH_CTRL0 , intf_val); + +return 0 ; +} + +static void mt8195_delay_ps2stage (struct mediatek_dwmac_plat_data *plat) +{ +struct mac_delay_struct *mac_delay = &plat->mac_delay; + +/* 290ps per stage */ + mac_delay->tx_delay /=290 ; + mac_delay->rx_delay /=290 ; +} + +static void mt8195_delay_stage2ps (struct mediatek_dwmac_plat_data *plat) +{ +struct mac_delay_struct *mac_delay = &plat->mac_delay; + +/* 290ps per stage */ + mac_delay->tx_delay *=290 ; + mac_delay->rx_delay *=290 ; +} + +static int mt8195_set_delay (struct mediatek_dwmac_plat_data *plat) +{ +struct mac_delay_struct *mac_delay = &plat->mac_delay; +u32 gtxc_delay_val =0 , delay_val =0 , rmii_delay_val =0 ; + +mt8195_delay_ps2stage (plat); + +switch (plat->phy_mode) { +case PHY_INTERFACE_MODE_MII : + delay_val |=FIELD_PREP (MT8195_DLY_TXC_ENABLE , !!mac_delay->tx_delay); + delay_val |=FIELD_PREP (MT8195_DLY_TXC_STAGES , mac_delay->tx_delay); + delay_val |=FIELD_PREP (MT8195_DLY_TXC_INV , mac_delay->tx_inv); + + delay_val |=FIELD_PREP (MT8195_DLY_RXC_ENABLE , !!mac_delay->rx_delay); + delay_val |=FIELD_PREP (MT8195_DLY_RXC_STAGES , mac_delay->rx_delay); + delay_val |=FIELD_PREP (MT8195_DLY_RXC_INV , mac_delay->rx_inv); +break ; +case PHY_INTERFACE_MODE_RMII : +if (plat->rmii_clk_from_mac) { +/* case 1: mac provides the rmii reference clock, +* and the clock output to TXC pin. +* The egress timing can be adjusted by RMII_TXC delay macro circuit. +* The ingress timing can be adjusted by RMII_RXC delay macro circuit. +*/ + rmii_delay_val |=FIELD_PREP (MT8195_DLY_RMII_TXC_ENABLE , + !!mac_delay->tx_delay); + rmii_delay_val |=FIELD_PREP (MT8195_DLY_RMII_TXC_STAGES , + mac_delay->tx_delay); + rmii_delay_val |=FIELD_PREP (MT8195_DLY_RMII_TXC_INV , + mac_delay->tx_inv); + + rmii_delay_val |=FIELD_PREP (MT8195_DLY_RMII_RXC_ENABLE , + !!mac_delay->rx_delay); + rmii_delay_val |=FIELD_PREP (MT8195_DLY_RMII_RXC_STAGES , + mac_delay->rx_delay); + rmii_delay_val |=FIELD_PREP (MT8195_DLY_RMII_RXC_INV , + mac_delay->rx_inv); + }else { +/* case 2: the rmii reference clock is from external phy, +* and the property "rmii_rxc" indicates which pin(TXC/RXC) +* the reference clk is connected to. The reference clock is a +* received signal, so rx_delay/rx_inv are used to indicate +* the reference clock timing adjustment +*/ +if (plat->rmii_rxc) { +/* the rmii reference clock from outside is connected +* to RXC pin, the reference clock will be adjusted +* by RXC delay macro circuit. +*/ + delay_val |=FIELD_PREP (MT8195_DLY_RXC_ENABLE , + !!mac_delay->rx_delay); + delay_val |=FIELD_PREP (MT8195_DLY_RXC_STAGES , + mac_delay->rx_delay); + delay_val |=FIELD_PREP (MT8195_DLY_RXC_INV , + mac_delay->rx_inv); + }else { +/* the rmii reference clock from outside is connected +* to TXC pin, the reference clock will be adjusted +* by TXC delay macro circuit. +*/ + delay_val |=FIELD_PREP (MT8195_DLY_TXC_ENABLE , + !!mac_delay->rx_delay); + delay_val |=FIELD_PREP (MT8195_DLY_TXC_STAGES , + mac_delay->rx_delay); + delay_val |=FIELD_PREP (MT8195_DLY_TXC_INV , + mac_delay->rx_inv); + } + } +break ; +case PHY_INTERFACE_MODE_RGMII : +case PHY_INTERFACE_MODE_RGMII_TXID : +case PHY_INTERFACE_MODE_RGMII_RXID : +case PHY_INTERFACE_MODE_RGMII_ID : + gtxc_delay_val |=FIELD_PREP (MT8195_DLY_GTXC_ENABLE , !!mac_delay->tx_delay); + gtxc_delay_val |=FIELD_PREP (MT8195_DLY_GTXC_STAGES , mac_delay->tx_delay); + gtxc_delay_val |=FIELD_PREP (MT8195_DLY_GTXC_INV , mac_delay->tx_inv); + + delay_val |=FIELD_PREP (MT8195_DLY_RXC_ENABLE , !!mac_delay->rx_delay); + delay_val |=FIELD_PREP (MT8195_DLY_RXC_STAGES , mac_delay->rx_delay); + delay_val |=FIELD_PREP (MT8195_DLY_RXC_INV , mac_delay->rx_inv); + +break ; +default : +dev_err (plat->dev,"phy interface not supported\n" ); +return -EINVAL ; + } + +regmap_update_bits (plat->peri_regmap, +MT8195_PERI_ETH_CTRL0 , +MT8195_RGMII_TXC_PHASE_CTRL | +MT8195_DLY_GTXC_INV | +MT8195_DLY_GTXC_ENABLE | +MT8195_DLY_GTXC_STAGES , + gtxc_delay_val); +regmap_write (plat->peri_regmap,MT8195_PERI_ETH_CTRL1 , delay_val); +regmap_write (plat->peri_regmap,MT8195_PERI_ETH_CTRL2 , rmii_delay_val); + +mt8195_delay_stage2ps (plat); + +return 0 ; +} + +static void mt8195_fix_mac_speed (void *priv,unsigned int speed) +{ +struct mediatek_dwmac_plat_data *priv_plat = priv; + +if ((phy_interface_mode_is_rgmii (priv_plat->phy_mode))) { +/* prefer 2ns fixed delay which is controlled by TXC_PHASE_CTRL, +* when link speed is 1Gbps with RGMII interface, +* Fall back to delay macro circuit for 10/100Mbps link speed. +*/ +if (speed ==SPEED_1000 ) +regmap_update_bits (priv_plat->peri_regmap, +MT8195_PERI_ETH_CTRL0 , +MT8195_RGMII_TXC_PHASE_CTRL | +MT8195_DLY_GTXC_ENABLE | +MT8195_DLY_GTXC_INV | +MT8195_DLY_GTXC_STAGES , +MT8195_RGMII_TXC_PHASE_CTRL ); +else +mt8195_set_delay (priv_plat); + } +} + +static const struct mediatek_dwmac_variant mt8195_gmac_variant = { + .dwmac_set_phy_interface = mt8195_set_interface, + .dwmac_set_delay = mt8195_set_delay, + .dwmac_fix_mac_speed = mt8195_fix_mac_speed, + .clk_list = mt8195_dwmac_clk_l, + .num_clks =ARRAY_SIZE (mt8195_dwmac_clk_l), + .dma_bit_mask =35 , + .rx_delay_max =9280 , + .tx_delay_max =9280 , +}; +static int mediatek_dwmac_config_dt (struct mediatek_dwmac_plat_data *plat) {struct mac_delay_struct *mac_delay = &plat->mac_delay;
@@ -307,6 +538,7 @@ static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat) mac_delay->rx_inv =of_property_read_bool (plat->np,"mediatek,rxc-inverse" ); plat->rmii_rxc =of_property_read_bool (plat->np,"mediatek,rmii-rxc" ); plat->rmii_clk_from_mac =of_property_read_bool (plat->np,"mediatek,rmii-clk-from-mac" ); + plat->mac_wol =of_property_read_bool (plat->np,"mediatek,mac-wol" );return 0 ; }
@@ -383,6 +615,7 @@ static int mediatek_dwmac_clks_config(void *priv, bool enabled)return ret; } +static int mediatek_dwmac_probe (struct platform_device *pdev) {struct mediatek_dwmac_plat_data *priv_plat;
@@ -420,7 +653,7 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)return PTR_ERR (plat_dat); plat_dat->interface = priv_plat->phy_mode; - plat_dat->use_phy_wol =1 ; + plat_dat->use_phy_wol = priv_plat->mac_wol ?0 :1 ; plat_dat->riwt_off =1 ; plat_dat->maxmtu =ETH_DATA_LEN ; plat_dat->addr64 = priv_plat->variant->dma_bit_mask;
@@ -428,7 +661,23 @@ static int mediatek_dwmac_probe(struct platform_device *pdev) plat_dat->init = mediatek_dwmac_init; plat_dat->exit = mediatek_dwmac_exit; plat_dat->clks_config = mediatek_dwmac_clks_config; +if (priv_plat->variant->dwmac_fix_mac_speed) + plat_dat->fix_mac_speed = priv_plat->variant->dwmac_fix_mac_speed; + plat_dat->safety_feat_cfg =devm_kzalloc (&pdev->dev, +sizeof (*plat_dat->safety_feat_cfg), +GFP_KERNEL ); +if (!plat_dat->safety_feat_cfg) +return -ENOMEM ; + plat_dat->safety_feat_cfg->tsoee =1 ; + plat_dat->safety_feat_cfg->mrxpee =0 ; + plat_dat->safety_feat_cfg->mestee =1 ; + plat_dat->safety_feat_cfg->mrxee =1 ; + plat_dat->safety_feat_cfg->mtxee =1 ; + plat_dat->safety_feat_cfg->epsi =0 ; + plat_dat->safety_feat_cfg->edpp =1 ; + plat_dat->safety_feat_cfg->prtyen =1 ; + plat_dat->safety_feat_cfg->tmouten =1 ;mediatek_dwmac_init (pdev, priv_plat); ret =stmmac_dvr_probe (&pdev->dev, plat_dat, &stmmac_res);
@@ -443,6 +692,8 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)static const struct of_device_id mediatek_dwmac_match[] = { { .compatible ="mediatek,mt2712-gmac" , .data = &mt2712_gmac_variant }, + { .compatible ="mediatek,mt8195-gmac" , + .data = &mt8195_gmac_variant }, { } };
Signature · 1 line
2.25.1
PATCH v8 6/6 net: dt-bindings: dwmac: add support for mt8195
In reply to Biao HuangAdd binding document for the ethernet on mt8195.
--- .../bindings/net/mediatek-dwmac.yaml | 86 +++++++++++++++---- 1 file changed, 70 insertions(+), 16 deletions(-)
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +70 -16
@@ -19,11 +19,67 @@ select: contains: enum: - mediatek,mt2712-gmac + - mediatek,mt8195-gmac required: - compatible allOf: - $ref: "snps,dwmac.yaml#" + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt2712-gmac + + then: + properties: + clocks: + minItems: 5 + items: + - description: AXI clock + - description: APB clock + - description: MAC Main clock + - description: PTP clock + - description: RMII reference clock provided by MAC + + clock-names: + minItems: 5 + items: + - const: axi + - const: apb + - const: mac_main + - const: ptp_ref + - const: rmii_internal + + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8195-gmac + + then: + properties: + clocks: + minItems: 6 + items: + - description: AXI clock + - description: APB clock + - description: MAC clock gate + - description: MAC Main clock + - description: PTP clock + - description: RMII reference clock provided by MAC + + clock-names: + minItems: 6 + items: + - const: axi + - const: apb + - const: mac_cg + - const: mac_main + - const: ptp_ref + - const: rmii_internal properties: compatible:
@@ -32,22 +88,10 @@ properties: - enum: - mediatek,mt2712-gmac - const: snps,dwmac-4.20a - - clocks: - items: - - description: AXI clock - - description: APB clock - - description: MAC Main clock - - description: PTP clock - - description: RMII reference clock provided by MAC - - clock-names: - items: - - const: axi - - const: apb - - const: mac_main - - const: ptp_ref - - const: rmii_internal + - items: + - enum: + - mediatek,mt8195-gmac + - const: snps,dwmac-5.10a mediatek,pericfg: $ref: /schemas/types.yaml#/definitions/phandle
@@ -62,6 +106,8 @@ properties: or will round down. Range 0~31*170. For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, or will round down. Range 0~31*550. + For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290, + or will round down. Range 0~31*290. mediatek,rx-delay-ps: description:
@@ -70,6 +116,8 @@ properties: or will round down. Range 0~31*170. For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, or will round down. Range 0~31*550. + For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple + of 290, or will round down. Range 0~31*290. mediatek,rmii-rxc: type: boolean
@@ -103,6 +151,12 @@ properties: 3. the inside clock, which be sent to MAC, will be inversed in RMII case when the reference clock is from MAC. + mediatek,mac-wol: + type: boolean + description: + If present, indicates that MAC supports WOL(Wake-On-LAN), and MAC WOL will be enabled. + Otherwise, PHY WOL is perferred. + required: - compatible - reg
Signature · 1 line
2.25.1
Rob Herring
maintainerRe: [PATCH net-next v8 6/6] net: dt-bindings: dwmac: add support for mt8195
Quoted 7 lines · Biao Huang
Add binding document for the ethernet on mt8195.
Signed-off-by Biao Huang <[email protected]>--- .../bindings/net/mediatek-dwmac.yaml | 86 +++++++++++++++---- 1 file changed, 70 insertions(+), 16 deletions(-)
Running 'make dtbs_check' with the schema in this patch gives the following warnings. Consider if they are expected or the schema is incorrect. These may not be new warnings.
Note that it is not yet a requirement to have 0 warnings for dtbs_check. This will change in the future.
Full log is available here: https://patchwork.ozlabs.org/patch/1566168
ethernet@1101c000: clock-names: ['axi', 'apb', 'mac_main', 'ptp_ref'] is too short
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: clocks: [[27, 34], [27, 37], [6, 154], [6, 155]] is too short
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: compatible: ['mediatek,mt2712-gmac'] does not contain items matching the given schema
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: compatible: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: Unevaluated properties are not allowed ('compatible', 'reg', 'interrupts', 'interrupt-names', 'mac-address', 'clock-names', 'clocks', 'assigned-clocks', 'assigned-clock-parents', 'power-domains', 'snps,axi-config', 'snps,mtl-rx-config', 'snps,mtl-tx-config', 'snps,txpbl', 'snps,rxpbl', 'clk_csr', 'phy-mode', 'phy-handle', 'snps,reset-gpio', 'mdio' were unexpected)
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
Rob Herring
maintainerRe: [PATCH net-next v8 6/6] net: dt-bindings: dwmac: add support for mt8195
In reply to Biao HuangQuoted 53 lines · Biao Huang
Add binding document for the ethernet on mt8195.
Signed-off-by Biao Huang <[email protected]>--- .../bindings/net/mediatek-dwmac.yaml | 86 +++++++++++++++---- 1 file changed, 70 insertions(+), 16 deletions(-)Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +33
-0@@ -19,11 +19,67 @@ select: contains: enum: - mediatek,mt2712-gmac + - mediatek,mt8195-gmac required: - compatible allOf: - $ref: "snps,dwmac.yaml#" + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt2712-gmac + + then: + properties: + clocks: + minItems: 5 + items: + - description: AXI clock + - description: APB clock + - description: MAC Main clock + - description: PTP clock + - description: RMII reference clock provided by MAC + + clock-names: + minItems: 5 + items: + - const: axi + - const: apb + - const: mac_main + - const: ptp_ref + - const: rmii_internal + + - if: + properties: + compatible: + contains: + enum:
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml select: · line 69
Quoted 10 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +10
-0+ - mediatek,mt8195-gmac + + then: + properties: + clocks: + minItems: 6 + items: + - description: AXI clock + - description: APB clock + - description: MAC clock gate
Add new clocks on to the end of existing clocks. That will simplify the binding as here you will just need 'minItems: 6'.
Quoted 78 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +27
-16+ - description: MAC Main clock + - description: PTP clock + - description: RMII reference clock provided by MAC + + clock-names: + minItems: 6 + items: + - const: axi + - const: apb + - const: mac_cg + - const: mac_main + - const: ptp_ref + - const: rmii_internal properties: compatible:@@ -32,22 +88,10 @@ properties: - enum: - mediatek,mt2712-gmac - const: snps,dwmac-4.20a - - clocks: - items: - - description: AXI clock - - description: APB clock - - description: MAC Main clock - - description: PTP clock - - description: RMII reference clock provided by MAC - - clock-names: - items: - - const: axi - - const: apb - - const: mac_main - - const: ptp_ref - - const: rmii_internal + - items: + - enum: + - mediatek,mt8195-gmac + - const: snps,dwmac-5.10a mediatek,pericfg: $ref: /schemas/types.yaml#/definitions/phandle@@ -62,6 +106,8 @@ properties: or will round down. Range 0~31*170. For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, or will round down. Range 0~31*550. + For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290, + or will round down. Range 0~31*290. mediatek,rx-delay-ps: description:@@ -70,6 +116,8 @@ properties: or will round down. Range 0~31*170. For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, or will round down. Range 0~31*550. + For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple + of 290, or will round down. Range 0~31*290. mediatek,rmii-rxc: type: boolean@@ -103,6 +151,12 @@ properties: 3. the inside clock, which be sent to MAC, will be inversed in RMII case when the reference clock is from MAC. + mediatek,mac-wol: + type: boolean + description: + If present, indicates that MAC supports WOL(Wake-On-LAN), and MAC WOL will be enabled. + Otherwise, PHY WOL is perferred. + required: - compatible - regSignature · 1 line
2.25.1
Re: [PATCH net-next v8 6/6] net: dt-bindings: dwmac: add support for mt8195
Dear Rob,
Thanks for your comment~
Quoted 63 lines · Rob Herring
Quoted 62 lines · Biao Huang
Add binding document for the ethernet on mt8195.
Signed-off-by Biao Huang <[email protected]>--- .../bindings/net/mediatek-dwmac.yaml | 86 +++++++++++++++---- 1 file changed, 70 insertions(+), 16 deletions(-)(quoted diff) +0
-0
dwmac.yamlb/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
index9207266a6e69..fb04166404d8100644Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +39
-0@@ -19,11 +19,67 @@ select: contains: enum: - mediatek,mt2712-gmac + - mediatek,mt8195-gmac required: - compatible allOf: - $ref: "snps,dwmac.yaml#" + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt2712-gmac + + then: + properties: + clocks: + minItems: 5 + items: + - description: AXI clock + - description: APB clock + - description: MAC Main clock + - description: PTP clock + - description: RMII reference clock provided by MAC + + clock-names: + minItems: 5 + items: + - const: axi + - const: apb + - const: mac_main + - const: ptp_ref + - const: rmii_internal + + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8195-gmac + + then: + properties: + clocks: + minItems: 6
Quoted 8 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml select: · line 69
Quoted 4 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +4
-0+ items: + - description: AXI clock + - description: APB clock + - description: MAC clock gateAdd new clocks on to the end of existing clocks. That will simplify the
binding as here you will just need 'minItems: 6'.
The "rmii_internal" clock is a special one we put it to the end on purpose, and will turn it on/off in driver according to whether phy_mode is rmii or not.
So the "mac_cg" clock, which is new for mt8195, and not used in mt2712, can't put it to the end for simplicity.
Can we just keep it this way? or other suggestions?
[v3 reply]
http://lists.infradead.org/pipermail/linux-mediatek/2021-November/031951.html
Quoted 84 lines
Quoted 84 lines
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +19
-16+ - description: MAC Main clock + - description: PTP clock + - description: RMII reference clock provided by MAC + + clock-names: + minItems: 6 + items: + - const: axi + - const: apb + - const: mac_cg + - const: mac_main + - const: ptp_ref + - const: rmii_internal properties: compatible:@@ -32,22 +88,10 @@ properties: - enum: - mediatek,mt2712-gmac - const: snps,dwmac-4.20a - - clocks: - items: - - description: AXI clock - - description: APB clock - - description: MAC Main clock - - description: PTP clock - - description: RMII reference clock provided by MAC - - clock-names: - items: - - const: axi - - const: apb - - const: mac_main - - const: ptp_ref - - const: rmii_internal + - items: + - enum: + - mediatek,mt8195-gmac + - const: snps,dwmac-5.10a mediatek,pericfg: $ref: /schemas/types.yaml#/definitions/phandle@@ -62,6 +106,8 @@ properties: or will round down. Range 0~31*170. For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, or will round down. Range 0~31*550. + For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290, + or will round down. Range 0~31*290.mediatek,rx-delay-ps:
description:Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +1
-0@@ -70,6 +116,8 @@ properties: or will round down. Range 0~31*170. For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, or will round down. Range 0~31*550. + For MT8195 RGMII/RMII/MII interface, Allowed value need tobe a multiple
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +1
-0+ of 290, or will round down. Range 0~31*290. mediatek,rmii-rxc: type: boolean@@ -103,6 +151,12 @@ properties: 3. the inside clock, which be sent to MAC, will be inversedin RMII case when
the reference clock is from MAC.Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +4
-0+ mediatek,mac-wol: + type: boolean + description: + If present, indicates that MAC supports WOL(Wake-On-LAN),and MAC WOL will be enabled.
Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +2
-0+ Otherwise, PHY WOL is perferred. + required: - compatible - regSignature · 1 line
2.25.1