5.10.89-rc1 review
Greg Kroah-Hartman
maintainercover 5.10.89-rc1 review
This is the start of the stable review cycle for the 5.10.89 release. There are 76 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Wed, 29 Dec 2021 15:13:09 +0000. Anything received after that time might be too late.
The whole patch series can be found in one patch at:
https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.10.89-rc1.gz
or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.10.y
and the diffstat can be found below.
thanks,
greg k-h
-------------
Pseudo-Shortlog of commits:
Greg Kroah-Hartman <[email protected]>
Linux 5.10.89-rc1
Rémi Denis-Courmont <[email protected]>
phonet/pep: refuse to enable an unbound pipe
Lin Ma <[email protected]>
hamradio: improve the incomplete fix to avoid NPD
Lin Ma <[email protected]>
hamradio: defer ax25 kfree after unregister_netdev
Lin Ma <[email protected]>
ax25: NPD bug when detaching AX25 device
Guenter Roeck <[email protected]>
hwmon: (lm90) Do not report 'busy' status bit as alarm
Guenter Roeck <[email protected]>
hwmom: (lm90) Fix citical alarm status for MAX6680/MAX6681
Guodong Liu <[email protected]>
pinctrl: mediatek: fix global-out-of-bounds issue
Derek Fang <[email protected]>
ASoC: rt5682: fix the wrong jack type detected
Martin Povišer <[email protected]>
ASoC: tas2770: Fix setting of high sample rates
Hans de Goede <[email protected]>
Input: goodix - add id->model mapping for the "9111" model
Samuel Čavoj <[email protected]>
Input: i8042 - enable deferred probe quirk for ASUS UM325UA
Johnny Chuang <[email protected]>
Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312
Andrey Ryabinin <[email protected]>
mm: mempolicy: fix THP allocations escaping mempolicy restrictions
Sean Christopherson <[email protected]>
KVM: VMX: Fix stale docs for kvm-intel.emulate_invalid_guest_state
Marian Postevca <[email protected]>
usb: gadget: u_ether: fix race in setting MAC address in setup phase
Christian Brauner <[email protected]>
ceph: fix up non-directory creation in SGID directories
Chao Yu <[email protected]>
f2fs: fix to do sanity check on last xattr entry in __f2fs_setxattr()
Sumit Garg <[email protected]>
tee: optee: Fix incorrect page free bug
Liu Shixin <[email protected]>
mm/hwpoison: clear MF_COUNT_INCREASED before retrying get_any_page()
Johannes Berg <[email protected]>
mac80211: fix locking in ieee80211_start_ap error path
Ard Biesheuvel <[email protected]>
ARM: 9169/1: entry: fix Thumb2 bug in iWMMXt exception handling
Yann Gautier <[email protected]>
mmc: mmci: stm32: clear DLYB_CR after sending tuning command
Ulf Hansson <[email protected]>
mmc: core: Disable card detect during shutdown
Martin Blumenstingl <[email protected]>
mmc: meson-mx-sdhc: Set MANUAL_STOP for multi-block SDIO commands
Prathamesh Shete <[email protected]>
mmc: sdhci-tegra: Fix switch to HS400ES mode
Noralf Trønnes <[email protected]>
gpio: dln2: Fix interrupts when replugging the device
Fabien Dessenne <[email protected]>
pinctrl: stm32: consider the GPIO offset to expose all the GPIO lines
Sean Christopherson <[email protected]>
KVM: VMX: Wake vCPU when delivering posted IRQ even if vCPU == this vCPU
Johan Hovold <[email protected]>
platform/x86: intel_pmc_core: fix memleak on registration failure
Andrew Cooper <[email protected]>
x86/pkey: Fix undefined behaviour with PKRU_WD_BIT
Jens Wiklander <[email protected]>
tee: handle lookup of shm with reference count 0
John David Anglin <[email protected]>
parisc: Fix mask used to select futex spinlock
John David Anglin <[email protected]>
parisc: Correct completer in lws start
Thadeu Lima de Souza Cascardo <[email protected]>
ipmi: fix initialization when workqueue allocation fails
Mian Yousaf Kaukab <[email protected]>
ipmi: ssif: initialize ssif_info->client early
Thadeu Lima de Souza Cascardo <[email protected]>
ipmi: bail out if init_srcu_struct fails
José Expósito <[email protected]>
Input: atmel_mxt_ts - fix double free in mxt_read_info_block
Martin Blumenstingl <[email protected]>
ASoC: meson: aiu: Move AIU_I2S_MISC hold setting to aiu-fifo-i2s
Werner Sembach <[email protected]>
ALSA: hda/realtek: Fix quirk for Clevo NJ51CU
Bradley Scott <[email protected]>
ALSA: hda/realtek: Add new alc285-hp-amp-init model
Bradley Scott <[email protected]>
ALSA: hda/realtek: Amp init fixup for HP ZBook 15 G6
Colin Ian King <[email protected]>
ALSA: drivers: opl3: Fix incorrect use of vp->state
Xiaoke Wang <[email protected]>
ALSA: jack: Check the return value of kstrdup()
Guenter Roeck <[email protected]>
hwmon: (lm90) Drop critical attribute support for MAX6654
Guenter Roeck <[email protected]>
hwmon: (lm90) Introduce flag indicating extended temperature support
Guenter Roeck <[email protected]>
hwmon: (lm90) Add basic support for TI TMP461
Guenter Roeck <[email protected]>
hwmon: (lm90) Fix usage of CONFIG2 register in detect function
Phil Elwell <[email protected]>
pinctrl: bcm2835: Change init order for gpio hogs
Andrea Righi <[email protected]>
Input: elantech - fix stack out of bound access in elantech_change_report_id()
Jiasheng Jiang <[email protected]>
sfc: falcon: Check null pointer of rx_queue->page_ring
Jiasheng Jiang <[email protected]>
sfc: Check null pointer of rx_queue->page_ring
Jiasheng Jiang <[email protected]>
net: ks8851: Check for error irq
Jiasheng Jiang <[email protected]>
drivers: net: smc911x: Check for error irq
Jiasheng Jiang <[email protected]>
fjes: Check for error irq
Fernando Fernandez Mancera <[email protected]>
bonding: fix ad_actor_system option setting to default
Wu Bo <[email protected]>
ipmi: Fix UAF when uninstall ipmi_si and ipmi_msghandler module
Heiner Kallweit <[email protected]>
igb: fix deadlock caused by taking RTNL in RPM resume path
Willem de Bruijn <[email protected]>
net: skip virtio_net_hdr_set_proto if protocol already set
Willem de Bruijn <[email protected]>
net: accept UFOv6 packages in virtio_net_hdr_to_skb
Jiasheng Jiang <[email protected]>
qlcnic: potential dereference null pointer of rx_queue->page_ring
Yevhen Orlov <[email protected]>
net: marvell: prestera: fix incorrect return of port_find
Martin Haaß <[email protected]>
ARM: dts: imx6qdl-wandboard: Fix Ethernet support
Ignacy Gawędzki <[email protected]>
netfilter: fix regression in looped (broad|multi)cast's MAC handling
Jiacheng Shi <[email protected]>
RDMA/hns: Replace kfree() with kvfree()
José Expósito <[email protected]>
IB/qib: Fix memory leak in qib_user_sdma_queue_pkts()
Martin Blumenstingl <[email protected]>
ASoC: meson: aiu: fifo: Add missing dma_coerce_mask_and_coherent()
Dongliang Mu <[email protected]>
spi: change clk_disable_unprepare to clk_unprepare
Robert Marko <[email protected]>
arm64: dts: allwinner: orangepi-zero-plus: fix PHY mode
Jiasheng Jiang <[email protected]>
HID: potential dereference of null pointer
Benjamin Tissoires <[email protected]>
HID: holtek: fix mouse probing
Zhang Yi <[email protected]>
ext4: check for inconsistent extents between index and leaf block
Zhang Yi <[email protected]>
ext4: check for out-of-order index extents in ext4_valid_extent_entries()
Zhang Yi <[email protected]>
ext4: prevent partial update of the extent blocks
Greg Jesionowski <[email protected]>
net: usb: lan78xx: add Allied Telesis AT29M2-AF
Nick Desaulniers <[email protected]>
arm64: vdso32: require CROSS_COMPILE_COMPAT for gcc+bfd
Nick Desaulniers <[email protected]>
arm64: vdso32: drop -no-integrated-as flag
-------------
Diffstat:
Documentation/admin-guide/kernel-parameters.txt | 8 +- Documentation/hwmon/lm90.rst | 10 ++ Documentation/networking/bonding.rst | 11 +- Documentation/sound/hd-audio/models.rst | 2 + Makefile | 4 +- arch/arm/boot/dts/imx6qdl-wandboard.dtsi | 1 + arch/arm/kernel/entry-armv.S | 8 +- arch/arm64/Kconfig | 3 +- .../dts/allwinner/sun50i-h5-orangepi-zero-plus.dts | 2 +- arch/arm64/kernel/vdso32/Makefile | 25 +-- arch/parisc/include/asm/futex.h | 4 +- arch/parisc/kernel/syscall.S | 2 +- arch/x86/include/asm/pgtable.h | 4 +- arch/x86/kvm/vmx/vmx.c | 3 +- drivers/char/ipmi/ipmi_msghandler.c | 21 ++- drivers/char/ipmi/ipmi_ssif.c | 7 +- drivers/gpio/gpio-dln2.c | 19 ++- drivers/hid/hid-holtek-mouse.c | 15 ++ drivers/hid/hid-vivaldi.c | 3 + drivers/hwmon/Kconfig | 2 +- drivers/hwmon/lm90.c | 171 +++++++++++++-------- drivers/infiniband/hw/hns/hns_roce_srq.c | 2 +- drivers/infiniband/hw/qib/qib_user_sdma.c | 2 +- drivers/input/mouse/elantech.c | 8 +- drivers/input/serio/i8042-x86ia64io.h | 7 + drivers/input/touchscreen/atmel_mxt_ts.c | 2 +- drivers/input/touchscreen/elants_i2c.c | 46 +++++- drivers/input/touchscreen/goodix.c | 1 + drivers/mmc/core/core.c | 7 +- drivers/mmc/core/core.h | 1 + drivers/mmc/core/host.c | 9 ++ drivers/mmc/host/meson-mx-sdhc-mmc.c | 16 ++ drivers/mmc/host/mmci_stm32_sdmmc.c | 2 + drivers/mmc/host/sdhci-tegra.c | 43 ++++-- drivers/net/bonding/bond_options.c | 2 +- drivers/net/ethernet/intel/igb/igb_main.c | 19 ++- .../net/ethernet/marvell/prestera/prestera_main.c | 16 +- drivers/net/ethernet/micrel/ks8851_par.c | 2 + drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov.h | 2 +- .../ethernet/qlogic/qlcnic/qlcnic_sriov_common.c | 12 +- .../net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c | 4 +- drivers/net/ethernet/sfc/falcon/rx.c | 5 +- drivers/net/ethernet/sfc/rx_common.c | 5 +- drivers/net/ethernet/smsc/smc911x.c | 5 + drivers/net/fjes/fjes_main.c | 5 + drivers/net/hamradio/mkiss.c | 5 +- drivers/net/usb/lan78xx.c | 6 + drivers/pinctrl/bcm/pinctrl-bcm2835.c | 29 ++-- drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c | 8 +- drivers/pinctrl/stm32/pinctrl-stm32.c | 8 +- drivers/platform/x86/intel_pmc_core_pltdrv.c | 2 +- drivers/spi/spi-armada-3700.c | 2 +- drivers/tee/optee/shm_pool.c | 6 +- drivers/tee/tee_shm.c | 171 ++++++++------------- drivers/usb/gadget/function/u_ether.c | 15 +- fs/ceph/file.c | 18 ++- fs/ext4/extents.c | 93 +++++++---- fs/f2fs/xattr.c | 11 +- include/linux/tee_drv.h | 4 +- include/linux/virtio_net.h | 25 ++- mm/memory-failure.c | 1 + mm/mempolicy.c | 4 +- net/ax25/af_ax25.c | 4 +- net/mac80211/cfg.c | 3 + net/netfilter/nfnetlink_log.c | 3 +- net/netfilter/nfnetlink_queue.c | 3 +- net/phonet/pep.c | 2 + sound/core/jack.c | 4 + sound/drivers/opl3/opl3_midi.c | 2 +- sound/pci/hda/patch_realtek.c | 28 +++- sound/soc/codecs/rt5682.c | 4 + sound/soc/codecs/tas2770.c | 4 +- sound/soc/meson/aiu-encoder-i2s.c | 33 ---- sound/soc/meson/aiu-fifo-i2s.c | 19 +++ sound/soc/meson/aiu-fifo.c | 6 + 75 files changed, 677 insertions(+), 394 deletions(-)
Greg Kroah-Hartman
maintainerPATCH 1/76 arm64: vdso32: drop -no-integrated-as flag
From: Nick Desaulniers <[email protected]>
commit ef94340583eec5cb1544dc41a87baa4f684b3fe1 upstream.
Clang can assemble these files just fine; this is a relic from the top level Makefile conditionally adding this. We no longer need --prefix, --gcc-toolchain, or -Qunused-arguments flags either with this change, so remove those too.
To test building:
$ ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- \ CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make LLVM=1 LLVM_IAS=1 \ defconfig arch/arm64/kernel/vdso32/
--- arch/arm64/kernel/vdso32/Makefile | 8 -------- 1 file changed, 8 deletions(-)
arch/arm64/kernel/vdso32/Makefile +0 -8
@@ -10,15 +10,7 @@ include $(srctree)/lib/vdso/Makefile # Same as cc-*option, but using CC_COMPAT instead of CC ifeq ($(CONFIG_CC_IS_CLANG), y) -COMPAT_GCC_TOOLCHAIN_DIR := $(dir $(shell which $(CROSS_COMPILE_COMPAT)elfedit)) -COMPAT_GCC_TOOLCHAIN := $(realpath $(COMPAT_GCC_TOOLCHAIN_DIR)/..) - CC_COMPAT_CLANG_FLAGS := --target=$(notdir $(CROSS_COMPILE_COMPAT:%-=%)) -CC_COMPAT_CLANG_FLAGS += --prefix=$(COMPAT_GCC_TOOLCHAIN_DIR)$(notdir $(CROSS_COMPILE_COMPAT)) -CC_COMPAT_CLANG_FLAGS += -no-integrated-as -Qunused-arguments -ifneq ($(COMPAT_GCC_TOOLCHAIN),) -CC_COMPAT_CLANG_FLAGS += --gcc-toolchain=$(COMPAT_GCC_TOOLCHAIN) -endif CC_COMPAT ?= $(CC) CC_COMPAT += $(CC_COMPAT_CLANG_FLAGS)
Greg Kroah-Hartman
maintainerPATCH 2/76 arm64: vdso32: require CROSS_COMPILE_COMPAT for gcc+bfd
In reply to Greg Kroah-HartmanFrom: Nick Desaulniers <[email protected]>
commit 3e6f8d1fa18457d54b20917bd9174d27daf09ab9 upstream.
Similar to
commit 231ad7f409f1 ("Makefile: infer --target from ARCH for CC=clang") There really is no point in setting --target based on $CROSS_COMPILE_COMPAT for clang when the integrated assembler is being used, since
commit ef94340583ee ("arm64: vdso32: drop -no-integrated-as flag").
Allows COMPAT_VDSO to be selected without setting $CROSS_COMPILE_COMPAT when using clang and lld together.
Before:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 defconfig $ grep CONFIG_COMPAT_VDSO .config CONFIG_COMPAT_VDSO=y $ ARCH=arm64 make -j72 LLVM=1 defconfig $ grep CONFIG_COMPAT_VDSO .config $
After:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 defconfig $ grep CONFIG_COMPAT_VDSO .config CONFIG_COMPAT_VDSO=y $ ARCH=arm64 make -j72 LLVM=1 defconfig $ grep CONFIG_COMPAT_VDSO .config CONFIG_COMPAT_VDSO=y
--- arch/arm64/Kconfig | 3 ++- arch/arm64/kernel/vdso32/Makefile | 17 +++++------------ 2 files changed, 7 insertions(+), 13 deletions(-)
arch/arm64/Kconfig +2 -1
@@ -1265,7 +1265,8 @@ config KUSER_HELPERS config COMPAT_VDSO bool "Enable vDSO for 32-bit applications" - depends on !CPU_BIG_ENDIAN && "$(CROSS_COMPILE_COMPAT)" != "" + depends on !CPU_BIG_ENDIAN + depends on (CC_IS_CLANG && LD_IS_LLD) || "$(CROSS_COMPILE_COMPAT)" != "" select GENERIC_COMPAT_VDSO default y help
arch/arm64/kernel/vdso32/Makefile +5 -12
@@ -10,18 +10,15 @@ include $(srctree)/lib/vdso/Makefile # Same as cc-*option, but using CC_COMPAT instead of CC ifeq ($(CONFIG_CC_IS_CLANG), y) -CC_COMPAT_CLANG_FLAGS := --target=$(notdir $(CROSS_COMPILE_COMPAT:%-=%)) - CC_COMPAT ?= $(CC) -CC_COMPAT += $(CC_COMPAT_CLANG_FLAGS) - -ifneq ($(LLVM),) -LD_COMPAT ?= $(LD) +CC_COMPAT += --target=arm-linux-gnueabi else -LD_COMPAT ?= $(CROSS_COMPILE_COMPAT)ld +CC_COMPAT ?= $(CROSS_COMPILE_COMPAT)gcc endif + +ifeq ($(CONFIG_LD_IS_LLD), y) +LD_COMPAT ?= $(LD) else -CC_COMPAT ?= $(CROSS_COMPILE_COMPAT)gcc LD_COMPAT ?= $(CROSS_COMPILE_COMPAT)ld endif
@@ -47,10 +44,6 @@ VDSO_CPPFLAGS += $(LINUXINCLUDE) # Common C and assembly flags # From top-level Makefile VDSO_CAFLAGS := $(VDSO_CPPFLAGS) -ifneq ($(shell $(CC_COMPAT) --version 2>&1 | head -n 1 | grep clang),) -VDSO_CAFLAGS += --target=$(notdir $(CROSS_COMPILE_COMPAT:%-=%)) -endif - VDSO_CAFLAGS += $(call cc32-option,-fno-PIE) ifdef CONFIG_DEBUG_INFO VDSO_CAFLAGS += -g
Greg Kroah-Hartman
maintainerPATCH 3/76 net: usb: lan78xx: add Allied Telesis AT29M2-AF
In reply to Greg Kroah-HartmanFrom: Greg Jesionowski <[email protected]>
commit ef8a0f6eab1ca5d1a75c242c5c7b9d386735fa0a upstream.
This adds the vendor and product IDs for the AT29M2-AF which is a lan7801-based device.
--- drivers/net/usb/lan78xx.c | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/net/usb/lan78xx.c +6 -0
@@ -64,6 +64,8 @@#define LAN7801_USB_PRODUCT_ID (0x7801)#define LAN78XX_EEPROM_MAGIC (0x78A5)#define LAN78XX_OTP_MAGIC (0x78F3) +#define AT29M2AF_USB_VENDOR_ID (0x07C9) +#define AT29M2AF_USB_PRODUCT_ID (0x0012)#define MII_READ 1#define MII_WRITE 0
@@ -4142,6 +4144,10 @@ static const struct usb_device_id produc/* LAN7801 USB Gigabit Ethernet Device */ USB_DEVICE(LAN78XX_USB_VENDOR_ID, LAN7801_USB_PRODUCT_ID), }, + { +/* ATM2-AF USB Gigabit Ethernet Device */ + USB_DEVICE(AT29M2AF_USB_VENDOR_ID, AT29M2AF_USB_PRODUCT_ID), + }, {}, };MODULE_DEVICE_TABLE (usb, products);
Greg Kroah-Hartman
maintainerPATCH 4/76 ext4: prevent partial update of the extent blocks
In reply to Greg Kroah-HartmanFrom: Zhang Yi <[email protected]>
commit 0f2f87d51aebcf71a709b52f661d681594c7dffa upstream.
In the most error path of current extents updating operations are not roll back partial updates properly when some bad things happens(.e.g in ext4_ext_insert_extent()). So we may get an inconsistent extents tree if journal has been aborted due to IO error, which may probability lead to BUGON later when we accessing these extent entries in errors=continue mode. This patch drop extent buffer's verify flag before updatng the contents in ext4_ext_get_access(), and reset it after updating in __ext4_ext_dirty(). After this patch we could force to check the extent buffer if extents tree updating was break off, make sure the extents are consistent.
--- fs/ext4/extents.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-)
fs/ext4/extents.c +15 -2
@@ -136,14 +136,24 @@ int ext4_datasem_ensure_credits(handle_tstatic int ext4_ext_get_access (handle_t *handle,struct inode *inode,struct ext4_ext_path *path) { +int err =0 ; +if (path->p_bh) {/* path points to block */ BUFFER_TRACE (path->p_bh,"get_write_access" ); -return ext4_journal_get_write_access (handle, path->p_bh); + err =ext4_journal_get_write_access (handle, path->p_bh); +/* +* The extent buffer's verified bit will be set again in +* __ext4_ext_dirty(). We could leave an inconsistent +* buffer if the extents updating procudure break off du +* to some error happens, force to check it again. +*/ +if (!err) +clear_buffer_verified (path->p_bh); }/* path points to leaf/index in inode body */ /* we use in-core data, no need to protect them */ -return 0 ; +return err; }/*
@@ -164,6 +174,9 @@ static int __ext4_ext_dirty(const char */* path points to block */ err =__ext4_handle_dirty_metadata (where, line, handle, inode, path->p_bh); +/* Extents updating done, re-set verified flag */ +if (!err) +set_buffer_verified (path->p_bh); }else {/* path points to leaf/index in inode body */ err =ext4_mark_inode_dirty (handle, inode);
Greg Kroah-Hartman
maintainerPATCH 5/76 ext4: check for out-of-order index extents in ext4_valid_extent_entries()
In reply to Greg Kroah-HartmanFrom: Zhang Yi <[email protected]>
commit 8dd27fecede55e8a4e67eef2878040ecad0f0d33 upstream.
After commit 5946d089379a ("ext4: check for overlapping extents in ext4_valid_extent_entries()"), we can check out the overlapping extent entry in leaf extent blocks. But the out-of-order extent entry in index extent blocks could also trigger bad things if the filesystem is inconsistent. So this patch add a check to figure out the out-of-order index extents and return error.
--- fs/ext4/extents.c | 17 ++++++++++++----- 1 file changed, 12 insertions(+), 5 deletions(-)
fs/ext4/extents.c +12 -5
@@ -369,6 +369,9 @@ static int ext4_valid_extent_entries(str ext4_fsblk_t *pblk, int depth) {unsigned short entries; +ext4_lblk_t lblock =0 ; +ext4_lblk_t prev =0 ; +if (eh->eh_entries ==0 )return 1 ;
@@ -377,31 +380,35 @@ static int ext4_valid_extent_entries(strif (depth ==0 ) {/* leaf entries */ struct ext4_extent *ext =EXT_FIRST_EXTENT (eh); -ext4_lblk_t lblock =0 ; -ext4_lblk_t prev =0 ; -int len =0 ;while (entries) {if (!ext4_valid_extent (inode, ext))return 0 ;/* Check for overlapping extents */ lblock =le32_to_cpu (ext->ee_block); - len =ext4_ext_get_actual_len (ext);if ((lblock <= prev) && prev) { *pblk =ext4_ext_pblock (ext);return 0 ; } + prev = lblock +ext4_ext_get_actual_len (ext) -1 ; ext++; entries--; - prev = lblock + len -1 ; } }else {struct ext4_extent_idx *ext_idx =EXT_FIRST_INDEX (eh);while (entries) {if (!ext4_valid_extent_idx (inode, ext_idx))return 0 ; + +/* Check for overlapping index extents */ + lblock =le32_to_cpu (ext_idx->ei_block); +if ((lblock <= prev) && prev) { + *pblk =ext4_idx_pblock (ext_idx); +return 0 ; + } ext_idx++; entries--; + prev = lblock; } }return 1 ;
Greg Kroah-Hartman
maintainerPATCH 6/76 ext4: check for inconsistent extents between index and leaf block
In reply to Greg Kroah-HartmanFrom: Zhang Yi <[email protected]>
commit 9c6e071913792d80894cd0be98cc3c4b770e26d3 upstream.
Now that we can check out overlapping extents in leaf block and out-of-order index extents in index block. But the .ee_block in the first extent of one leaf block should equal to the .ei_block in it's parent index extent entry. This patch add a check to verify such inconsistent between the index and leaf block.
--- fs/ext4/extents.c | 59 ++++++++++++++++++++++++++++++++---------------------- 1 file changed, 36 insertions(+), 23 deletions(-)
fs/ext4/extents.c +36 -23
@@ -366,7 +366,8 @@ static int ext4_valid_extent_idx(structstatic int ext4_valid_extent_entries (struct inode *inode,struct ext4_extent_header *eh, -ext4_fsblk_t *pblk,int depth) +ext4_lblk_t lblk,ext4_fsblk_t *pblk, +int depth) {unsigned short entries;ext4_lblk_t lblock =0 ;
@@ -380,6 +381,14 @@ static int ext4_valid_extent_entries(strif (depth ==0 ) {/* leaf entries */ struct ext4_extent *ext =EXT_FIRST_EXTENT (eh); + +/* +* The logical block in the first entry should equal to +* the number in the index block. +*/ +if (depth !=ext_depth (inode) && + lblk !=le32_to_cpu (ext->ee_block)) +return 0 ;while (entries) {if (!ext4_valid_extent (inode, ext))return 0 ;
@@ -396,6 +405,14 @@ static int ext4_valid_extent_entries(str } }else {struct ext4_extent_idx *ext_idx =EXT_FIRST_INDEX (eh); + +/* +* The logical block in the first entry should equal to +* the number in the parent index block. +*/ +if (depth !=ext_depth (inode) && + lblk !=le32_to_cpu (ext_idx->ei_block)) +return 0 ;while (entries) {if (!ext4_valid_extent_idx (inode, ext_idx))return 0 ;
@@ -416,7 +433,7 @@ static int ext4_valid_extent_entries(strstatic int __ext4_ext_check (const char *function,unsigned int line,struct inode *inode,struct ext4_extent_header *eh, -int depth,ext4_fsblk_t pblk) +int depth,ext4_fsblk_t pblk,ext4_lblk_t lblk) {const char *error_msg;int max =0 , err = -EFSCORRUPTED ;
@@ -442,7 +459,7 @@ static int __ext4_ext_check(const char * error_msg ="invalid eh_entries" ; goto corrupted; } -if (!ext4_valid_extent_entries (inode, eh, &pblk, depth)) { +if (!ext4_valid_extent_entries (inode, eh, lblk, &pblk, depth)) { error_msg ="invalid extent entries" ; goto corrupted; }
@@ -472,7 +489,7 @@ corrupted: }#define ext4_ext_check (inode, eh, depth, pblk) \ - __ext4_ext_check(__func__, __LINE__, (inode), (eh), (depth), (pblk)) + __ext4_ext_check(__func__, __LINE__, (inode), (eh), (depth), (pblk), 0)int ext4_ext_check_inode (struct inode *inode) {
@@ -505,16 +522,18 @@ static void ext4_cache_extents(struct instatic struct buffer_head *__read_extent_tree_block (const char *function,unsigned int line, -struct inode *inode,ext4_fsblk_t pblk,int depth, -int flags) +struct inode *inode,struct ext4_extent_idx *idx, +int depth,int flags) {struct buffer_head *bh;int err;gfp_t gfp_flags = __GFP_MOVABLE |GFP_NOFS ; +ext4_fsblk_t pblk;if (flags &EXT4_EX_NOFAIL ) gfp_flags |= __GFP_NOFAIL; + pblk =ext4_idx_pblock (idx); bh =sb_getblk_gfp (inode->i_sb, pblk, gfp_flags);if (unlikely (!bh))return ERR_PTR (-ENOMEM );
@@ -527,8 +546,8 @@ __read_extent_tree_block(const char *fun }if (buffer_verified (bh) && !(flags &EXT4_EX_FORCE_CACHE ))return bh; - err =__ext4_ext_check (function, line, inode, -ext_block_hdr (bh), depth, pblk); + err =__ext4_ext_check (function, line, inode,ext_block_hdr (bh), + depth, pblk,le32_to_cpu (idx->ei_block));if (err) goto errout;set_buffer_verified (bh);
@@ -546,8 +565,8 @@ errout: } -#define read_extent_tree_block (inode, pblk, depth, flags) \ - __read_extent_tree_block(__func__, __LINE__, (inode), (pblk), \ +#define read_extent_tree_block (inode, idx, depth, flags) \ + __read_extent_tree_block(__func__, __LINE__, (inode), (idx), \ (depth), (flags))/*
@@ -597,8 +616,7 @@ int ext4_ext_precache(struct inode *inod i--;continue ; } - bh =read_extent_tree_block (inode, -ext4_idx_pblock (path[i].p_idx++), + bh =read_extent_tree_block (inode, path[i].p_idx++, depth - i -1 ,EXT4_EX_FORCE_CACHE );if (IS_ERR (bh)) {
@@ -903,8 +921,7 @@ ext4_find_extent(struct inode *inode, ex path[ppos].p_depth = i; path[ppos].p_ext =NULL ; - bh =read_extent_tree_block (inode, path[ppos].p_block, --i, - flags); + bh =read_extent_tree_block (inode, path[ppos].p_idx, --i, flags);if (IS_ERR (bh)) { ret =PTR_ERR (bh); goto err;
@@ -1509,7 +1526,6 @@ static int ext4_ext_search_right(structstruct ext4_extent_header *eh;struct ext4_extent_idx *ix;struct ext4_extent *ex; -ext4_fsblk_t block;int depth;/* Note, NOT eh_depth; depth from top of tree */ int ee_len;
@@ -1576,20 +1592,17 @@ got_index:* follow it and find the closest allocated * block to the right */ ix++; - block =ext4_idx_pblock (ix);while (++depth < path->p_depth) {/* subtract from p_depth to get proper eh_depth */ - bh =read_extent_tree_block (inode, block, - path->p_depth - depth,0 ); + bh =read_extent_tree_block (inode, ix, path->p_depth - depth,0 );if (IS_ERR (bh))return PTR_ERR (bh); eh =ext_block_hdr (bh); ix =EXT_FIRST_INDEX (eh); - block =ext4_idx_pblock (ix);put_bh (bh); } - bh =read_extent_tree_block (inode, block, path->p_depth - depth,0 ); + bh =read_extent_tree_block (inode, ix, path->p_depth - depth,0 );if (IS_ERR (bh))return PTR_ERR (bh); eh =ext_block_hdr (bh);
@@ -2968,9 +2981,9 @@ again:ext_debug (inode,"move to level %d (block %llu)\n" , i +1 ,ext4_idx_pblock (path[i].p_idx));memset (path + i +1 ,0 ,sizeof (*path)); - bh =read_extent_tree_block (inode, -ext4_idx_pblock (path[i].p_idx), depth - i -1 , -EXT4_EX_NOCACHE ); + bh =read_extent_tree_block (inode, path[i].p_idx, + depth - i -1 , +EXT4_EX_NOCACHE );if (IS_ERR (bh)) {/* should we reset i_size? */ err =PTR_ERR (bh);
Greg Kroah-Hartman
maintainerPATCH 7/76 HID: holtek: fix mouse probing
In reply to Greg Kroah-HartmanFrom: Benjamin Tissoires <[email protected]>
commit 93a2207c254ca102ebbdae47b00f19bbfbfa7ecd upstream.
An overlook from the previous commit: we don't even parse or start the device, meaning that the device is not presented to user space.
--- drivers/hid/hid-holtek-mouse.c | 15 +++++++++++++++ 1 file changed, 15 insertions(+)
drivers/hid/hid-holtek-mouse.c +15 -0
@@ -65,8 +65,23 @@ static __u8 *holtek_mouse_report_fixup(sstatic int holtek_mouse_probe (struct hid_device *hdev,const struct hid_device_id *id) { +int ret; +if (!hid_is_usb (hdev))return -EINVAL ; + + ret =hid_parse (hdev); +if (ret) { +hid_err (hdev,"hid parse failed: %d\n" , ret); +return ret; + } + + ret =hid_hw_start (hdev,HID_CONNECT_DEFAULT ); +if (ret) { +hid_err (hdev,"hw start failed: %d\n" , ret); +return ret; + } +return 0 ; }
Greg Kroah-Hartman
maintainerPATCH 8/76 HID: potential dereference of null pointer
In reply to Greg Kroah-HartmanFrom: Jiasheng Jiang <[email protected]>
commit 13251ce1dd9bb525da2becb9b26fdfb94ca58659 upstream.
The return value of devm_kzalloc() needs to be checked. To avoid hdev->dev->driver_data to be null in case of the failure of alloc.
--- drivers/hid/hid-vivaldi.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/hid/hid-vivaldi.c +3 -0
@@ -57,6 +57,9 @@ static int vivaldi_probe(struct hid_deviint ret; drvdata =devm_kzalloc (&hdev->dev,sizeof (*drvdata),GFP_KERNEL ); +if (!drvdata) +return -ENOMEM ; +hid_set_drvdata (hdev, drvdata); ret =hid_parse (hdev);
Greg Kroah-Hartman
maintainerPATCH 9/76 arm64: dts: allwinner: orangepi-zero-plus: fix PHY mode
In reply to Greg Kroah-HartmanFrom: Robert Marko <[email protected]>
[ Upstream commit 08d2061ff9c5319a07bf9ca6bbf11fdec68f704a ]
Orange Pi Zero Plus uses a Realtek RTL8211E RGMII Gigabit PHY, but its currently set to plain RGMII mode meaning that it doesn't introduce delays.
With this setup, TX packets are completely lost and changing the mode to RGMII-ID so the PHY will add delays internally fixes the issue.
--- arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts +1 -1
@@ -69,7 +69,7 @@ pinctrl-0 = <&emac_rgmii_pins>; phy-supply = <®_gmac_3v3>; phy-handle = <&ext_rgmii_phy>; - phy-mode = "rgmii"; + phy-mode = "rgmii-id"; status = "okay"; };
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 10/76 spi: change clk_disable_unprepare to clk_unprepare
In reply to Greg Kroah-HartmanFrom: Dongliang Mu <[email protected]>
[ Upstream commit db6689b643d8653092f5853751ea2cdbc299f8d3 ]
The corresponding API for clk_prepare is clk_unprepare, other than clk_disable_unprepare.
Fix this by changing clk_disable_unprepare to clk_unprepare.
--- drivers/spi/spi-armada-3700.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spi/spi-armada-3700.c +1 -1
@@ -901,7 +901,7 @@ static int a3700_spi_probe(struct platform_device *pdev)return 0 ; error_clk: -clk_disable_unprepare (spi->clk); +clk_unprepare (spi->clk); error:spi_master_put (master); out:
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 11/76 ASoC: meson: aiu: fifo: Add missing dma_coerce_mask_and_coherent()
In reply to Greg Kroah-HartmanFrom: Martin Blumenstingl <[email protected]>
[ Upstream commit 1bcd326631dc4faa3322d60b4fc45e8b3747993e ]
The FIFO registers which take an DMA-able address are only 32-bit wide on AIU. Add dma_coerce_mask_and_coherent() to make the DMA core aware of this limitation.
--- sound/soc/meson/aiu-fifo.c | 6 ++++++ 1 file changed, 6 insertions(+)
sound/soc/meson/aiu-fifo.c +6 -0
@@ -5,6 +5,7 @@#include <linux/bitfield.h> #include <linux/clk.h> +#include <linux/dma-mapping.h> #include <sound/pcm_params.h> #include <sound/soc.h> #include <sound/soc-dai.h>
@@ -192,6 +193,11 @@ int aiu_fifo_pcm_new(struct snd_soc_pcm_runtime *rtd,struct snd_card *card = rtd->card->snd_card;struct aiu_fifo *fifo = dai->playback_dma_data;size_t size = fifo->pcm->buffer_bytes_max; +int ret; + + ret =dma_coerce_mask_and_coherent (card->dev,DMA_BIT_MASK (32 )); +if (ret) +return ret; snd_pcm_lib_preallocate_pages(substream, SNDRV_DMA_TYPE_DEV,
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 12/76 IB/qib: Fix memory leak in qib_user_sdma_queue_pkts()
In reply to Greg Kroah-HartmanFrom: José Expósito <[email protected]>
[ Upstream commit bee90911e0138c76ee67458ac0d58b38a3190f65 ]
The wrong goto label was used for the error case and missed cleanup of the pkt allocation.
Addresses-Coverity-ID: 1493352 ("Resource leak")
--- drivers/infiniband/hw/qib/qib_user_sdma.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/infiniband/hw/qib/qib_user_sdma.c +1 -1
@@ -941,7 +941,7 @@ static int qib_user_sdma_queue_pkts(const struct qib_devdata *dd, &addrlimit) || addrlimit > type_max(typeof(pkt->addrlimit))) { ret = -EINVAL ; - goto free_pbc; + goto free_pkt; } pkt->addrlimit = addrlimit;
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 13/76 RDMA/hns: Replace kfree() with kvfree()
In reply to Greg Kroah-HartmanFrom: Jiacheng Shi <[email protected]>
[ Upstream commit 12d3bbdd6bd2780b71cc466f3fbc6eb7d43bbc2a ]
Variables allocated by kvmalloc_array() should not be freed by kfree. Because they may be allocated by vmalloc. So we replace kfree() with kvfree() here.
--- drivers/infiniband/hw/hns/hns_roce_srq.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/infiniband/hw/hns/hns_roce_srq.c +1 -1
@@ -277,7 +277,7 @@ static int alloc_srq_wrid(struct hns_roce_dev *hr_dev, struct hns_roce_srq *srq)static void free_srq_wrid (struct hns_roce_srq *srq) { -kfree (srq->wrid); +kvfree (srq->wrid); srq->wrid =NULL ; }
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 14/76 netfilter: fix regression in looped (broad|multi)casts MAC handling
In reply to Greg Kroah-HartmanFrom: Ignacy Gawędzki <[email protected]>
[ Upstream commit ebb966d3bdfed581ecccbb4a7432341baf7619b4 ]
In commit 5648b5e1169f ("netfilter: nfnetlink_queue: fix OOB when mac header was cleared"), the test for non-empty MAC header introduced in commit 2c38de4c1f8da7 ("netfilter: fix looped (broad|multi)cast's MAC handling") has been replaced with a test for a set MAC header.
This breaks the case when the MAC header has been reset (using skb_reset_mac_header), as is the case with looped-back multicast packets. As a result, the packets ending up in NFQUEUE get a bogus hwaddr interpreted from the first bytes of the IP header.
This patch adds a test for a non-empty MAC header in addition to the test for a set MAC header. The same two tests are also implemented in nfnetlink_log.c, where the initial code of commit 2c38de4c1f8da7 ("netfilter: fix looped (broad|multi)cast's MAC handling") has not been touched, but where supposedly the same situation may happen.
--- net/netfilter/nfnetlink_log.c | 3 ++- net/netfilter/nfnetlink_queue.c | 3 ++- 2 files changed, 4 insertions(+), 2 deletions(-)
net/netfilter/nfnetlink_log.c +2 -1
@@ -557,7 +557,8 @@ __build_packet_message(struct nfnl_log_net *log, goto nla_put_failure;if (indev && skb->dev && - skb->mac_header != skb->network_header) { +skb_mac_header_was_set (skb) && +skb_mac_header_len (skb) !=0 ) {struct nfulnl_msg_packet_hw phw;int len;
net/netfilter/nfnetlink_queue.c +2 -1
@@ -562,7 +562,8 @@ nfqnl_build_packet_message(struct net *net, struct nfqnl_instance *queue, goto nla_put_failure;if (indev && entskb->dev && -skb_mac_header_was_set (entskb)) { +skb_mac_header_was_set (entskb) && +skb_mac_header_len (entskb) !=0 ) {struct nfqnl_msg_packet_hw phw;int len;
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 15/76 ARM: dts: imx6qdl-wandboard: Fix Ethernet support
In reply to Greg Kroah-HartmanFrom: Martin Haaß <[email protected]>
[ Upstream commit 39e660687ac0c57499134765abbecf71cfd11eae ]
Currently, the imx6q-wandboard Ethernet does not transmit any data.
This issue has been exposed by commit f5d9aa79dfdf ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested by the commit above.
--- arch/arm/boot/dts/imx6qdl-wandboard.dtsi | 1 + 1 file changed, 1 insertion(+)
arch/arm/boot/dts/imx6qdl-wandboard.dtsi +1 -0
@@ -289,6 +289,7 @@ ethphy: ethernet-phy@1 { reg = <1>; + qca,clk-out-frequency = <125000000>; }; }; };
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 16/76 net: marvell: prestera: fix incorrect return of port_find
In reply to Greg Kroah-HartmanFrom: Yevhen Orlov <[email protected]>
[ Upstream commit 8b681bd7c301c423fbe97a6b23388a2180ff04ca ]
In case, when some ports is in list and we don't find requested - we return last iterator state and not return NULL as expected.
--- .../ethernet/marvell/prestera/prestera_main.c | 16 ++++++++++------ 1 file changed, 10 insertions(+), 6 deletions(-)
drivers/net/ethernet/marvell/prestera/prestera_main.c +10 -6
@@ -50,12 +50,14 @@ int prestera_port_pvid_set(struct prestera_port *port, u16 vid)struct prestera_port *prestera_port_find_by_hwid (struct prestera_switch *sw,u32 dev_id,u32 hw_id) { -struct prestera_port *port =NULL ; +struct prestera_port *port =NULL , *tmp;read_lock (&sw->port_list_lock); -list_for_each_entry (port, &sw->port_list, list) { -if (port->dev_id == dev_id && port->hw_id == hw_id) +list_for_each_entry (tmp, &sw->port_list, list) { +if (tmp->dev_id == dev_id && tmp->hw_id == hw_id) { + port = tmp;break ; + } }read_unlock (&sw->port_list_lock);
@@ -64,12 +66,14 @@ struct prestera_port *prestera_port_find_by_hwid(struct prestera_switch *sw,struct prestera_port *prestera_find_port (struct prestera_switch *sw,u32 id) { -struct prestera_port *port =NULL ; +struct prestera_port *port =NULL , *tmp;read_lock (&sw->port_list_lock); -list_for_each_entry (port, &sw->port_list, list) { -if (port->id == id) +list_for_each_entry (tmp, &sw->port_list, list) { +if (tmp->id == id) { + port = tmp;break ; + } }read_unlock (&sw->port_list_lock);
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 17/76 qlcnic: potential dereference null pointer of rx_queue->page_ring
In reply to Greg Kroah-HartmanFrom: Jiasheng Jiang <[email protected]>
[ Upstream commit 60ec7fcfe76892a1479afab51ff17a4281923156 ]
The return value of kcalloc() needs to be checked.
To avoid dereference of null pointer in case of the failure of alloc. Therefore, it might be better to change the return type of qlcnic_sriov_alloc_vlans() and return -ENOMEM when alloc fails and return 0 the others.
Also, qlcnic_sriov_set_guest_vlan_mode() and __qlcnic_pci_sriov_enable() should deal with the return value of qlcnic_sriov_alloc_vlans().
--- drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov.h | 2 +- .../net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c | 12 +++++++++--- drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c | 4 +++- 3 files changed, 13 insertions(+), 5 deletions(-)
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov.h +1 -1
@@ -201,7 +201,7 @@ int qlcnic_sriov_get_vf_vport_info(struct qlcnic_adapter *, struct qlcnic_info *, u16);int qlcnic_sriov_cfg_vf_guest_vlan (struct qlcnic_adapter *,u16 ,u8 );void qlcnic_sriov_free_vlans (struct qlcnic_adapter *); -void qlcnic_sriov_alloc_vlans (struct qlcnic_adapter *); +int qlcnic_sriov_alloc_vlans (struct qlcnic_adapter *);bool qlcnic_sriov_check_any_vlan (struct qlcnic_vf_info *);void qlcnic_sriov_del_vlan_id (struct qlcnic_sriov *,struct qlcnic_vf_info *,u16 );
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c +9 -3
@@ -432,7 +432,7 @@ static int qlcnic_sriov_set_guest_vlan_mode(struct qlcnic_adapter *adapter, struct qlcnic_cmd_args *cmd) {struct qlcnic_sriov *sriov = adapter->ahw->sriov; -int i, num_vlans; +int i, num_vlans, ret;u16 *vlans;if (sriov->allowed_vlans)
@@ -443,7 +443,9 @@ static int qlcnic_sriov_set_guest_vlan_mode(struct qlcnic_adapter *adapter,dev_info (&adapter->pdev->dev,"Number of allowed Guest VLANs = %d\n" , sriov->num_allowed_vlans); -qlcnic_sriov_alloc_vlans (adapter); + ret =qlcnic_sriov_alloc_vlans (adapter); +if (ret) +return ret;if (!sriov->any_vlan)return 0 ;
@@ -2159,7 +2161,7 @@ static int qlcnic_sriov_vf_resume(struct qlcnic_adapter *adapter)return err; } -void qlcnic_sriov_alloc_vlans (struct qlcnic_adapter *adapter) +int qlcnic_sriov_alloc_vlans (struct qlcnic_adapter *adapter) {struct qlcnic_sriov *sriov = adapter->ahw->sriov;struct qlcnic_vf_info *vf;
@@ -2169,7 +2171,11 @@ void qlcnic_sriov_alloc_vlans(struct qlcnic_adapter *adapter) vf = &sriov->vf_info[i]; vf->sriov_vlans =kcalloc (sriov->num_allowed_vlans,sizeof (*vf->sriov_vlans),GFP_KERNEL ); +if (!vf->sriov_vlans) +return -ENOMEM ; } + +return 0 ; }void qlcnic_sriov_free_vlans (struct qlcnic_adapter *adapter)
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c +3 -1
@@ -597,7 +597,9 @@ static int __qlcnic_pci_sriov_enable(struct qlcnic_adapter *adapter,if (err) goto del_flr_queue; -qlcnic_sriov_alloc_vlans (adapter); + err =qlcnic_sriov_alloc_vlans (adapter); +if (err) + goto del_flr_queue;return err;
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 18/76 net: accept UFOv6 packages in virtio_net_hdr_to_skb
In reply to Greg Kroah-HartmanFrom: Willem de Bruijn <[email protected]>
[ Upstream commit 7e5cced9ca84df52d874aca6b632f930b3dc5bc6 ]
Skb with skb->protocol 0 at the time of virtio_net_hdr_to_skb may have a protocol inferred from virtio_net_hdr with virtio_net_hdr_set_proto.
Unlike TCP, UDP does not have separate types for IPv4 and IPv6. Type VIRTIO_NET_HDR_GSO_UDP is guessed to be IPv4/UDP. As of the below commit, UFOv6 packets are dropped due to not matching the protocol as obtained from dev_parse_header_protocol.
Invert the test to take that L2 protocol field as starting point and pass both UFOv4 and UFOv6 for VIRTIO_NET_HDR_GSO_UDP.
--- include/linux/virtio_net.h | 22 ++++++++++++++++++++-- 1 file changed, 20 insertions(+), 2 deletions(-)
include/linux/virtio_net.h +20 -2
@@ -7,6 +7,21 @@#include <uapi/linux/udp.h> #include <uapi/linux/virtio_net.h> +static inline bool virtio_net_hdr_match_proto (__be16 protocol,__u8 gso_type) +{ +switch (gso_type & ~VIRTIO_NET_HDR_GSO_ECN ) { +case VIRTIO_NET_HDR_GSO_TCPV4 : +return protocol ==cpu_to_be16 (ETH_P_IP ); +case VIRTIO_NET_HDR_GSO_TCPV6 : +return protocol ==cpu_to_be16 (ETH_P_IPV6 ); +case VIRTIO_NET_HDR_GSO_UDP : +return protocol ==cpu_to_be16 (ETH_P_IP ) || + protocol ==cpu_to_be16 (ETH_P_IPV6 ); +default : +return false; + } +} +static inline int virtio_net_hdr_set_proto (struct sk_buff *skb,const struct virtio_net_hdr *hdr) {
@@ -88,9 +103,12 @@ static inline int virtio_net_hdr_to_skb(struct sk_buff *skb,if (!skb->protocol) {__be16 protocol =dev_parse_header_protocol (skb); -virtio_net_hdr_set_proto (skb, hdr); -if (protocol && protocol != skb->protocol) +if (!protocol) +virtio_net_hdr_set_proto (skb, hdr); +else if (!virtio_net_hdr_match_proto (protocol, hdr->gso_type))return -EINVAL ; +else + skb->protocol = protocol; } retry: if (!skb_flow_dissect_flow_keys_basic(NULL, skb, &keys,
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 19/76 net: skip virtio_net_hdr_set_proto if protocol already set
In reply to Greg Kroah-HartmanFrom: Willem de Bruijn <[email protected]>
[ Upstream commit 1ed1d592113959f00cc552c3b9f47ca2d157768f ]
virtio_net_hdr_set_proto infers skb->protocol from the virtio_net_hdr gso_type, to avoid packets getting dropped for lack of a proto type.
Its protocol choice is a guess, especially in the case of UFO, where the single VIRTIO_NET_HDR_GSO_UDP label covers both UFOv4 and UFOv6.
Skip this best effort if the field is already initialized. Whether explicitly from userspace, or implicitly based on an earlier call to dev_parse_header_protocol (which is more robust, but was introduced after this patch).
--- include/linux/virtio_net.h | 3 +++ 1 file changed, 3 insertions(+)
include/linux/virtio_net.h +3 -0
@@ -25,6 +25,9 @@ static inline bool virtio_net_hdr_match_proto(__be16 protocol, __u8 gso_type)static inline int virtio_net_hdr_set_proto (struct sk_buff *skb,const struct virtio_net_hdr *hdr) { +if (skb->protocol) +return 0 ; +switch (hdr->gso_type & ~VIRTIO_NET_HDR_GSO_ECN ) {case VIRTIO_NET_HDR_GSO_TCPV4 :case VIRTIO_NET_HDR_GSO_UDP :
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 20/76 igb: fix deadlock caused by taking RTNL in RPM resume path
In reply to Greg Kroah-HartmanFrom: Heiner Kallweit <[email protected]>
[ Upstream commit ac8c58f5b535d6272324e2b8b4a0454781c9147e ]
Recent net core changes caused an issue with few Intel drivers (reportedly igb), where taking RTNL in RPM resume path results in a deadlock. See [0] for a bug report. I don't think the core changes are wrong, but taking RTNL in RPM resume path isn't needed. The Intel drivers are the only ones doing this. See [1] for a discussion on the issue. Following patch changes the RPM resume path to not take RTNL.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=215129
[1] https://lore.kernel.org/netdev/20211125074949.5f897431@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/t/
--- drivers/net/ethernet/intel/igb/igb_main.c | 19 +++++++++++++------ 1 file changed, 13 insertions(+), 6 deletions(-)
drivers/net/ethernet/intel/igb/igb_main.c +13 -6
@@ -9260,7 +9260,7 @@ static int __maybe_unused igb_suspend(struct device *dev)return __igb_shutdown (to_pci_dev (dev),NULL ,0 ); } -static int __maybe_unused igb_resume (struct device *dev) +static int __maybe_unused __igb_resume (struct device *dev,bool rpm) {struct pci_dev *pdev =to_pci_dev (dev);struct net_device *netdev =pci_get_drvdata (pdev);
@@ -9303,17 +9303,24 @@ static int __maybe_unused igb_resume(struct device *dev)wr32 (E1000_WUS , ~0 ); -rtnl_lock (); +if (!rpm) +rtnl_lock ();if (!err &&netif_running (netdev)) err =__igb_open (netdev, true);if (!err)netif_device_attach (netdev); -rtnl_unlock (); +if (!rpm) +rtnl_unlock ();return err; } +static int __maybe_unused igb_resume (struct device *dev) +{ +return __igb_resume (dev, false); +} +static int __maybe_unused igb_runtime_idle (struct device *dev) {struct net_device *netdev =dev_get_drvdata (dev);
@@ -9332,7 +9339,7 @@ static int __maybe_unused igb_runtime_suspend(struct device *dev)static int __maybe_unused igb_runtime_resume (struct device *dev) { -return igb_resume (dev); +return __igb_resume (dev, true); }static void igb_shutdown (struct pci_dev *pdev)
@@ -9448,7 +9455,7 @@ static pci_ers_result_t igb_io_error_detected(struct pci_dev *pdev,* @pdev: Pointer to PCI device * * Restart the card from scratch, as if from a cold-boot. Implementation -* resembles the first-half of the igb_resume routine. +* resembles the first-half of the __igb_resume routine. **/ static pci_ers_result_t igb_io_slot_reset (struct pci_dev *pdev) {
@@ -9488,7 +9495,7 @@ static pci_ers_result_t igb_io_slot_reset(struct pci_dev *pdev)* * This callback is called when the error recovery driver tells us that * its OK to resume normal operation. Implementation resembles the -* second-half of the igb_resume routine. +* second-half of the __igb_resume routine. */ static void igb_io_resume (struct pci_dev *pdev) {
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 21/76 ipmi: Fix UAF when uninstall ipmi_si and ipmi_msghandler module
In reply to Greg Kroah-HartmanFrom: Wu Bo <[email protected]>
[ Upstream commit ffb76a86f8096a8206be03b14adda6092e18e275 ]
Hi,
When testing install and uninstall of ipmi_si.ko and ipmi_msghandler.ko, the system crashed.
The log as follows:
[ 141.087026] BUG: unable to handle kernel paging request at ffffffffc09b3a5a [ 141.087241] PGD 8fe4c0d067 P4D 8fe4c0d067 PUD 8fe4c0f067 PMD 103ad89067 PTE 0 [ 141.087464] Oops: 0010 [#1] SMP NOPTI [ 141.087580] CPU: 67 PID: 668 Comm: kworker/67:1 Kdump: loaded Not tainted 4.18.0.x86_64 #47 [ 141.088009] Workqueue: events 0xffffffffc09b3a40 [ 141.088009] RIP: 0010:0xffffffffc09b3a5a [ 141.088009] Code: Bad RIP value. [ 141.088009] RSP: 0018:ffffb9094e2c3e88 EFLAGS: 00010246 [ 141.088009] RAX: 0000000000000000 RBX: ffff9abfdb1f04a0 RCX: 0000000000000000 [ 141.088009] RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246 [ 141.088009] RBP: 0000000000000000 R08: ffff9abfffee3cb8 R09: 00000000000002e1 [ 141.088009] R10: ffffb9094cb73d90 R11: 00000000000f4240 R12: ffff9abfffee8700 [ 141.088009] R13: 0000000000000000 R14: ffff9abfdb1f04a0 R15: ffff9abfdb1f04a8 [ 141.088009] FS: 0000000000000000(0000) GS:ffff9abfffec0000(0000) knlGS:0000000000000000 [ 141.088009] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 141.088009] CR2: ffffffffc09b3a30 CR3: 0000008fe4c0a001 CR4: 00000000007606e0 [ 141.088009] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 141.088009] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 141.088009] PKRU: 55555554 [ 141.088009] Call Trace: [ 141.088009] ? process_one_work+0x195/0x390 [ 141.088009] ? worker_thread+0x30/0x390 [ 141.088009] ? process_one_work+0x390/0x390 [ 141.088009] ? kthread+0x10d/0x130 [ 141.088009] ? kthread_flush_work_fn+0x10/0x10 [ 141.088009] ? ret_from_fork+0x35/0x40] BUG: unable to handle kernel paging request at ffffffffc0b28a5a [ 200.223240] PGD 97fe00d067 P4D 97fe00d067 PUD 97fe00f067 PMD a580cbf067 PTE 0 [ 200.223464] Oops: 0010 [#1] SMP NOPTI [ 200.223579] CPU: 63 PID: 664 Comm: kworker/63:1 Kdump: loaded Not tainted 4.18.0.x86_64 #46 [ 200.224008] Workqueue: events 0xffffffffc0b28a40 [ 200.224008] RIP: 0010:0xffffffffc0b28a5a [ 200.224008] Code: Bad RIP value. [ 200.224008] RSP: 0018:ffffbf3c8e2a3e88 EFLAGS: 00010246 [ 200.224008] RAX: 0000000000000000 RBX: ffffa0799ad6bca0 RCX: 0000000000000000 [ 200.224008] RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246 [ 200.224008] RBP: 0000000000000000 R08: ffff9fe43fde3cb8 R09: 00000000000000d5 [ 200.224008] R10: ffffbf3c8cb53d90 R11: 00000000000f4240 R12: ffff9fe43fde8700 [ 200.224008] R13: 0000000000000000 R14: ffffa0799ad6bca0 R15: ffffa0799ad6bca8 [ 200.224008] FS: 0000000000000000(0000) GS:ffff9fe43fdc0000(0000) knlGS:0000000000000000 [ 200.224008] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 200.224008] CR2: ffffffffc0b28a30 CR3: 00000097fe00a002 CR4: 00000000007606e0 [ 200.224008] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 200.224008] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 200.224008] PKRU: 55555554 [ 200.224008] Call Trace: [ 200.224008] ? process_one_work+0x195/0x390 [ 200.224008] ? worker_thread+0x30/0x390 [ 200.224008] ? process_one_work+0x390/0x390 [ 200.224008] ? kthread+0x10d/0x130 [ 200.224008] ? kthread_flush_work_fn+0x10/0x10 [ 200.224008] ? ret_from_fork+0x35/0x40 [ 200.224008] kernel fault(0x1) notification starting on CPU 63 [ 200.224008] kernel fault(0x1) notification finished on CPU 63 [ 200.224008] CR2: ffffffffc0b28a5a [ 200.224008] ---[ end trace c82a412d93f57412 ]---
The reason is as follows:
T1: rmmod ipmi_si.
->ipmi_unregister_smi()
-> ipmi_bmc_unregister()
-> __ipmi_bmc_unregister()
-> kref_put(&bmc->usecount, cleanup_bmc_device);
-> schedule_work(&bmc->remove_work);T2: rmmod ipmi_msghandler.
ipmi_msghander module uninstalled, and the module space will be freed.
T3: bmc->remove_work doing cleanup the bmc resource.
-> cleanup_bmc_work()
-> platform_device_unregister(&bmc->pdev);
-> platform_device_del(pdev);
-> device_del(&pdev->dev);
-> kobject_uevent(&dev->kobj, KOBJ_REMOVE);
-> kobject_uevent_env()
-> dev_uevent()
-> if (dev->type && dev->type->name)'dev->type'(bmc_device_type) pointer space has freed when uninstall
ipmi_msghander module, 'dev->type->name' cause the system crash.
drivers/char/ipmi/ipmi_msghandler.c:
2820 static const struct device_type bmc_device_type = {
2821 .groups = bmc_dev_attr_groups,
2822 };
Steps to reproduce:
Add a time delay in cleanup_bmc_work() function,
and uninstall ipmi_si and ipmi_msghandler module.
2910 static void cleanup_bmc_work(struct work_struct *work) 2911 {
2912 struct bmc_device *bmc = container_of(work, struct bmc_device,
2913 remove_work);
2914 int id = bmc->pdev.id; /* Unregister overwrites id */
2915
2916 msleep(3000); <--- 2917 platform_device_unregister(&bmc->pdev); 2918 ida_simple_remove(&ipmi_bmc_ida, id);
2919 }
Use 'remove_work_wq' instead of 'system_wq' to solve this issues.
Message-Id: <[email protected]>
--- drivers/char/ipmi/ipmi_msghandler.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/char/ipmi/ipmi_msghandler.c +1 -1
@@ -2945,7 +2945,7 @@ cleanup_bmc_device(struct kref *ref)* with removing the device attributes while reading a device * attribute. */ -schedule_work (&bmc->remove_work); +queue_work (remove_work_wq, &bmc->remove_work); }/*
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 22/76 bonding: fix ad_actor_system option setting to default
In reply to Greg Kroah-HartmanFrom: Fernando Fernandez Mancera <[email protected]>
[ Upstream commit 1c15b05baea71a5ff98235783e3e4ad227760876 ]
When 802.3ad bond mode is configured the ad_actor_system option is set to "00:00:00:00:00:00". But when trying to set the all-zeroes MAC as actors' system address it was failing with EINVAL.
An all-zeroes ethernet address is valid, only multicast addresses are not valid values.
--- Documentation/networking/bonding.rst | 11 ++++++----- drivers/net/bonding/bond_options.c | 2 +- 2 files changed, 7 insertions(+), 6 deletions(-)
Documentation/networking/bonding.rst +6 -5
@@ -196,11 +196,12 @@ ad_actor_sys_prio ad_actor_system In an AD system, this specifies the mac-address for the actor in - protocol packet exchanges (LACPDUs). The value cannot be NULL or - multicast. It is preferred to have the local-admin bit set for this - mac but driver does not enforce it. If the value is not given then - system defaults to using the masters' mac address as actors' system - address. + protocol packet exchanges (LACPDUs). The value cannot be a multicast + address. If the all-zeroes MAC is specified, bonding will internally + use the MAC of the bond itself. It is preferred to have the + local-admin bit set for this mac but driver does not enforce it. If + the value is not given then system defaults to using the masters' + mac address as actors' system address. This parameter has effect only in 802.3ad mode and is available through SysFs interface.
drivers/net/bonding/bond_options.c +1 -1
@@ -1466,7 +1466,7 @@ static int bond_option_ad_actor_system_set(struct bonding *bond, mac = (u8 *)&newval->value; } -if (!is_valid_ether_addr (mac)) +if (is_multicast_ether_addr (mac)) goto err;netdev_dbg (bond->dev,"Setting ad_actor_system to %pM\n" , mac);
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 23/76 fjes: Check for error irq
In reply to Greg Kroah-HartmanFrom: Jiasheng Jiang <[email protected]>
[ Upstream commit db6d6afe382de5a65d6ccf51253ab48b8e8336c3 ]
I find that platform_get_irq() will not always succeed.
It will return error irq in case of the failure.
Therefore, it might be better to check it if order to avoid the use of error irq.
--- drivers/net/fjes/fjes_main.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/net/fjes/fjes_main.c +5 -0
@@ -1269,6 +1269,11 @@ static int fjes_probe(struct platform_device *plat_dev) hw->hw_res.start = res->start; hw->hw_res.size =resource_size (res); hw->hw_res.irq =platform_get_irq (plat_dev,0 ); +if (hw->hw_res.irq <0 ) { + err = hw->hw_res.irq; + goto err_free_control_wq; + } + err =fjes_hw_init (&adapter->hw);if (err) goto err_free_control_wq;
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 24/76 drivers: net: smc911x: Check for error irq
In reply to Greg Kroah-HartmanFrom: Jiasheng Jiang <[email protected]>
[ Upstream commit cb93b3e11d405f20a405a07482d01147ef4934a3 ]
Because platform_get_irq() could fail and return error irq. Therefore, it might be better to check it if order to avoid the use of error irq.
--- drivers/net/ethernet/smsc/smc911x.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/net/ethernet/smsc/smc911x.c +5 -0
@@ -2069,6 +2069,11 @@ static int smc911x_drv_probe(struct platform_device *pdev) ndev->dma = (unsigned char )-1 ; ndev->irq =platform_get_irq (pdev,0 ); +if (ndev->irq <0 ) { + ret = ndev->irq; + goto release_both; + } + lp =netdev_priv (ndev); lp->netdev = ndev;#ifdef SMC_DYNAMIC_BUS_CONFIG
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 25/76 net: ks8851: Check for error irq
In reply to Greg Kroah-HartmanFrom: Jiasheng Jiang <[email protected]>
[ Upstream commit 99d7fbb5cedf598f67e8be106d6c7b8d91366aef ]
Because platform_get_irq() could fail and return error irq. Therefore, it might be better to check it if order to avoid the use of error irq.
--- drivers/net/ethernet/micrel/ks8851_par.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/net/ethernet/micrel/ks8851_par.c +2 -0
@@ -323,6 +323,8 @@ static int ks8851_probe_par(struct platform_device *pdev)return ret; netdev->irq =platform_get_irq (pdev,0 ); +if (netdev->irq <0 ) +return netdev->irq;return ks8851_probe_common (netdev, dev, msg_enable); }
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 26/76 sfc: Check null pointer of rx_queue->page_ring
In reply to Greg Kroah-HartmanFrom: Jiasheng Jiang <[email protected]>
[ Upstream commit bdf1b5c3884f6a0dc91b0dbdb8c3b7d205f449e0 ]
Because of the possible failure of the kcalloc, it should be better to set rx_queue->page_ptr_mask to 0 when it happens in order to maintain the consistency.
--- drivers/net/ethernet/sfc/rx_common.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/net/ethernet/sfc/rx_common.c +4 -1
@@ -150,7 +150,10 @@ static void efx_init_rx_recycle_ring(struct efx_rx_queue *rx_queue) efx->rx_bufs_per_page); rx_queue->page_ring =kcalloc (page_ring_size,sizeof (*rx_queue->page_ring),GFP_KERNEL ); - rx_queue->page_ptr_mask = page_ring_size -1 ; +if (!rx_queue->page_ring) + rx_queue->page_ptr_mask =0 ; +else + rx_queue->page_ptr_mask = page_ring_size -1 ; }static void efx_fini_rx_recycle_ring (struct efx_rx_queue *rx_queue)
Signature · 1 line
2.34.1
Re: [PATCH 5.10 26/76] sfc: Check null pointer of rx_queue->page_ring
hi!
Quoted 7 lines
From: Jiasheng Jiang <[email protected]>
[ Upstream commit
bdf1b5c3884f6a0dc91b0dbdb8c3b7d205f449e0]Because of the possible failure of the kcalloc, it should be better to set
rx_queue->page_ptr_maskto 0 when it happens in order to maintain the consistency.
This is confusing/wrong, or at least not a complete fix.
drivers/net/ethernet/sfc/rx_common.c static void efx_init_rx_recycle_ring(struct efx_rx_queue *rx_queue) · line 158
Quoted 12 lines
+++
b/drivers/net/ethernet/sfc/rx_common.cdrivers/net/ethernet/sfc/rx_common.c +4
-1@@ -150,7 +150,10 @@ static void efx_init_rx_recycle_ring(struct efx_rx_queue *rx_queue) efx->rx_bufs_per_page); rx_queue->page_ring =kcalloc (page_ring_size,sizeof (*rx_queue->page_ring),GFP_KERNEL ); - rx_queue->page_ptr_mask = page_ring_size -1 ; +if (!rx_queue->page_ring) + rx_queue->page_ptr_mask =0 ; +else + rx_queue->page_ptr_mask = page_ring_size -1 ; }
So we have !rx_queue->page_ring. But in efx_reuse_page, we do
index = rx_queue->page_remove & rx_queue->page_ptr_mask; page = rx_queue->page_ring[index];
So index is now zero, but we'll derefernce null pointer anyway.
Best regards,
Pavel
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Re: [PATCH 5.10 26/76] sfc: Check null pointer of rx_queue->page_ring
Quoted 27 lines · Pavel Machek
hi!
Quoted 7 lines
From: Jiasheng Jiang <[email protected]>
[ Upstream commit
bdf1b5c3884f6a0dc91b0dbdb8c3b7d205f449e0]Because of the possible failure of the kcalloc, it should be better to set
rx_queue->page_ptr_maskto 0 when it happens in order to maintain the consistency.This is confusing/wrong, or at least not a complete fix.
drivers/net/ethernet/sfc/rx_common.c static void efx_init_rx_recycle_ring(struct efx_rx_queue *rx_queue) · line 158
Quoted 12 lines
+++
b/drivers/net/ethernet/sfc/rx_common.cdrivers/net/ethernet/sfc/rx_common.c +4
-1@@ -150,7 +150,10 @@ static void efx_init_rx_recycle_ring(struct efx_rx_queue *rx_queue) efx->rx_bufs_per_page); rx_queue->page_ring =kcalloc (page_ring_size,sizeof (*rx_queue->page_ring),GFP_KERNEL ); - rx_queue->page_ptr_mask = page_ring_size -1 ; +if (!rx_queue->page_ring) + rx_queue->page_ptr_mask =0 ; +else + rx_queue->page_ptr_mask = page_ring_size -1 ; }So we have !rx_queue->page_ring. But in
efx_reuse_page, we do
Quoted 4 lines
index = rx_queue->page_remove & rx_queue->page_ptr_mask; page = rx_queue->page_ring[index];So index is now zero, but we'll derefernce null pointer anyway.
Good point. I've posted a patch for this to netdev.
https://lore.kernel.org/netdev/[email protected]/
Thanks,
Martin
Greg Kroah-Hartman
maintainerPATCH 27/76 sfc: falcon: Check null pointer of rx_queue->page_ring
In reply to Greg Kroah-HartmanFrom: Jiasheng Jiang <[email protected]>
[ Upstream commit 9b8bdd1eb5890aeeab7391dddcf8bd51f7b07216 ]
Because of the possible failure of the kcalloc, it should be better to set rx_queue->page_ptr_mask to 0 when it happens in order to maintain the consistency.
--- drivers/net/ethernet/sfc/falcon/rx.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/net/ethernet/sfc/falcon/rx.c +4 -1
@@ -728,7 +728,10 @@ static void ef4_init_rx_recycle_ring(struct ef4_nic *efx, efx->rx_bufs_per_page); rx_queue->page_ring =kcalloc (page_ring_size,sizeof (*rx_queue->page_ring),GFP_KERNEL ); - rx_queue->page_ptr_mask = page_ring_size -1 ; +if (!rx_queue->page_ring) + rx_queue->page_ptr_mask =0 ; +else + rx_queue->page_ptr_mask = page_ring_size -1 ; }void ef4_init_rx_queue (struct ef4_rx_queue *rx_queue)
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 28/76 Input: elantech - fix stack out of bound access in elantech_change_report_id()
In reply to Greg Kroah-HartmanFrom: Andrea Righi <[email protected]>
[ Upstream commit 1d72d9f960ccf1052a0630a68c3d358791dbdaaa ]
The array param[] in elantech_change_report_id() must be at least 3 bytes, because elantech_read_reg_params() is calling ps2_command() with PSMOUSE_CMD_GETINFO, that is going to access 3 bytes from param[], but it's defined in the stack as an array of 2 bytes, therefore we have a potential stack out-of-bounds access here, also confirmed by KASAN:
[ 6.512374] BUG: KASAN: stack-out-of-bounds in __ps2_command+0x372/0x7e0 [ 6.512397] Read of size 1 at addr ffff8881024d77c2 by task kworker/2:1/118
[ 6.512416] CPU: 2 PID: 118 Comm: kworker/2:1 Not tainted 5.13.0-22-generic #22+arighi20211110 [ 6.512428] Hardware name: LENOVO 20T8000QGE/20T8000QGE, BIOS R1AET32W (1.08 ) 08/14/2020 [ 6.512436] Workqueue: events_long serio_handle_event [ 6.512453] Call Trace: [ 6.512462] show_stack+0x52/0x58 [ 6.512474] dump_stack+0xa1/0xd3 [ 6.512487] print_address_description.constprop.0+0x1d/0x140 [ 6.512502] ? __ps2_command+0x372/0x7e0 [ 6.512516] __kasan_report.cold+0x7d/0x112 [ 6.512527] ? _raw_write_lock_irq+0x20/0xd0 [ 6.512539] ? __ps2_command+0x372/0x7e0 [ 6.512552] kasan_report+0x3c/0x50 [ 6.512564] __asan_load1+0x6a/0x70 [ 6.512575] __ps2_command+0x372/0x7e0 [ 6.512589] ? ps2_drain+0x240/0x240 [ 6.512601] ? dev_printk_emit+0xa2/0xd3 [ 6.512612] ? dev_vprintk_emit+0xc5/0xc5 [ 6.512621] ? __kasan_check_write+0x14/0x20 [ 6.512634] ? mutex_lock+0x8f/0xe0 [ 6.512643] ? __mutex_lock_slowpath+0x20/0x20 [ 6.512655] ps2_command+0x52/0x90 [ 6.512670] elantech_ps2_command+0x4f/0xc0 [psmouse] [ 6.512734] elantech_change_report_id+0x1e6/0x256 [psmouse] [ 6.512799] ? elantech_report_trackpoint.constprop.0.cold+0xd/0xd [psmouse] [ 6.512863] ? ps2_command+0x7f/0x90 [ 6.512877] elantech_query_info.cold+0x6bd/0x9ed [psmouse] [ 6.512943] ? elantech_setup_ps2+0x460/0x460 [psmouse] [ 6.513005] ? psmouse_reset+0x69/0xb0 [psmouse] [ 6.513064] ? psmouse_attr_set_helper+0x2a0/0x2a0 [psmouse] [ 6.513122] ? phys_pmd_init+0x30e/0x521 [ 6.513137] elantech_init+0x8a/0x200 [psmouse] [ 6.513200] ? elantech_init_ps2+0xf0/0xf0 [psmouse] [ 6.513249] ? elantech_query_info+0x440/0x440 [psmouse] [ 6.513296] ? synaptics_send_cmd+0x60/0x60 [psmouse] [ 6.513342] ? elantech_query_info+0x440/0x440 [psmouse] [ 6.513388] ? psmouse_try_protocol+0x11e/0x170 [psmouse] [ 6.513432] psmouse_extensions+0x65d/0x6e0 [psmouse] [ 6.513476] ? psmouse_try_protocol+0x170/0x170 [psmouse] [ 6.513519] ? mutex_unlock+0x22/0x40 [ 6.513526] ? ps2_command+0x7f/0x90 [ 6.513536] ? psmouse_probe+0xa3/0xf0 [psmouse] [ 6.513580] psmouse_switch_protocol+0x27d/0x2e0 [psmouse] [ 6.513624] psmouse_connect+0x272/0x530 [psmouse] [ 6.513669] serio_driver_probe+0x55/0x70 [ 6.513679] really_probe+0x190/0x720 [ 6.513689] driver_probe_device+0x160/0x1f0 [ 6.513697] device_driver_attach+0x119/0x130 [ 6.513705] ? device_driver_attach+0x130/0x130 [ 6.513713] __driver_attach+0xe7/0x1a0 [ 6.513720] ? device_driver_attach+0x130/0x130 [ 6.513728] bus_for_each_dev+0xfb/0x150 [ 6.513738] ? subsys_dev_iter_exit+0x10/0x10 [ 6.513748] ? _raw_write_unlock_bh+0x30/0x30 [ 6.513757] driver_attach+0x2d/0x40 [ 6.513764] serio_handle_event+0x199/0x3d0 [ 6.513775] process_one_work+0x471/0x740 [ 6.513785] worker_thread+0x2d2/0x790 [ 6.513794] ? process_one_work+0x740/0x740 [ 6.513802] kthread+0x1b4/0x1e0 [ 6.513809] ? set_kthread_struct+0x80/0x80 [ 6.513816] ret_from_fork+0x22/0x30
[ 6.513832] The buggy address belongs to the page: [ 6.513838] page:00000000bc35e189 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1024d7 [ 6.513847] flags: 0x17ffffc0000000(node=0|zone=2|lastcpupid=0x1fffff) [ 6.513860] raw: 0017ffffc0000000 dead000000000100 dead000000000122 0000000000000000 [ 6.513867] raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 [ 6.513872] page dumped because: kasan: bad access detected
[ 6.513879] addr ffff8881024d77c2 is located in stack of task kworker/2:1/118 at offset 34 in frame: [ 6.513887] elantech_change_report_id+0x0/0x256 [psmouse]
[ 6.513941] this frame has 1 object: [ 6.513947] [32, 34) 'param'
[ 6.513956] Memory state around the buggy address: [ 6.513962] ffff8881024d7680: f2 f2 f2 f2 f2 00 00 f3 f3 00 00 00 00 00 00 00 [ 6.513969] ffff8881024d7700: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 6.513976] >ffff8881024d7780: 00 00 00 00 f1 f1 f1 f1 02 f3 f3 f3 00 00 00 00 [ 6.513982] ^ [ 6.513988] ffff8881024d7800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 6.513995] ffff8881024d7880: 00 f1 f1 f1 f1 03 f2 03 f2 03 f3 f3 f3 00 00 00 [ 6.514000] ==================================================================
Define param[] in elantech_change_report_id() as an array of 3 bytes to prevent the out-of-bounds access in the stack.
--- drivers/input/mouse/elantech.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)
drivers/input/mouse/elantech.c +7 -1
@@ -1588,7 +1588,13 @@ static const struct dmi_system_id no_hw_res_dmi_table[] = {*/ static int elantech_change_report_id (struct psmouse *psmouse) { -unsigned char param[2 ] = {0x10 ,0x03 }; +/* +* NOTE: the code is expecting to receive param[] as an array of 3 +* items (see __ps2_command()), even if in this case only 2 are +* actually needed. Make sure the array size is 3 to avoid potential +* stack out-of-bound accesses. +*/ +unsigned char param[3 ] = {0x10 ,0x03 }; if (elantech_write_reg_params(psmouse, 0x7, param) || elantech_read_reg_params(psmouse, 0x7, param) ||
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 29/76 pinctrl: bcm2835: Change init order for gpio hogs
In reply to Greg Kroah-HartmanFrom: Phil Elwell <[email protected]>
[ Upstream commit 266423e60ea1b953fcc0cd97f3dad85857e434d1 ]
...and gpio-ranges
pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio side is registered first, but this breaks gpio hogs (which are configured during gpiochip_add_data). Part of the hog initialisation is a call to pinctrl_gpio_request, and since the pinctrl driver hasn't yet been registered this results in an -EPROBE_DEFER from which it can never recover.
Change the initialisation sequence to register the pinctrl driver first.
This also solves a similar problem with the gpio-ranges property, which is required in order for released pins to be returned to inputs.
--- drivers/pinctrl/bcm/pinctrl-bcm2835.c | 29 +++++++++++++++------------ 1 file changed, 16 insertions(+), 13 deletions(-)
drivers/pinctrl/bcm/pinctrl-bcm2835.c +16 -13
@@ -1244,6 +1244,18 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev)raw_spin_lock_init (&pc->irq_lock[i]); } + pc->pctl_desc = *pdata->pctl_desc; + pc->pctl_dev =devm_pinctrl_register (dev, &pc->pctl_desc, pc); +if (IS_ERR (pc->pctl_dev)) { +gpiochip_remove (&pc->gpio_chip); +return PTR_ERR (pc->pctl_dev); + } + + pc->gpio_range = *pdata->gpio_range; + pc->gpio_range.base = pc->gpio_chip.base; + pc->gpio_range.gc = &pc->gpio_chip; +pinctrl_add_gpio_range (pc->pctl_dev, &pc->gpio_range); + girq = &pc->gpio_chip.irq; girq->chip = &bcm2835_gpio_irq_chip; girq->parent_handler = bcm2835_gpio_irq_handler;
@@ -1251,8 +1263,10 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev) girq->parents =devm_kcalloc (dev,BCM2835_NUM_IRQS ,sizeof (*girq->parents),GFP_KERNEL ); -if (!girq->parents) +if (!girq->parents) { +pinctrl_remove_gpio_range (pc->pctl_dev, &pc->gpio_range);return -ENOMEM ; + }if (is_7211) { pc->wake_irq = devm_kcalloc(dev, BCM2835_NUM_IRQS,
@@ -1303,21 +1317,10 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev) err =gpiochip_add_data (&pc->gpio_chip, pc);if (err) {dev_err (dev,"could not add GPIO chip\n" ); +pinctrl_remove_gpio_range (pc->pctl_dev, &pc->gpio_range);return err; } - pc->pctl_desc = *pdata->pctl_desc; - pc->pctl_dev =devm_pinctrl_register (dev, &pc->pctl_desc, pc); -if (IS_ERR (pc->pctl_dev)) { -gpiochip_remove (&pc->gpio_chip); -return PTR_ERR (pc->pctl_dev); - } - - pc->gpio_range = *pdata->gpio_range; - pc->gpio_range.base = pc->gpio_chip.base; - pc->gpio_range.gc = &pc->gpio_chip; -pinctrl_add_gpio_range (pc->pctl_dev, &pc->gpio_range); -return 0 ; }
Signature · 1 line
2.34.1
Re: [PATCH 5.10 29/76] pinctrl: bcm2835: Change init order for gpio hogs
Hi!
Quoted 13 lines
From: Phil Elwell <[email protected]>
[ Upstream commit
266423e60ea1b953fcc0cd97f3dad85857e434d1]...and gpio-ranges
pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio side is registered first, but this breaks gpio hogs (which are configured during
gpiochip_add_data). Part of the hog initialisation is a call topinctrl_gpio_request, and since the pinctrl driver hasn't yet been registered this results in an -EPROBE_DEFER from which it can never recover.
Quoted 2 lines
Change the initialisation sequence to register the pinctrl driver first.
This does not get error handling right.
Quoted 5 lines
drivers/pinctrl/bcm/pinctrl-bcm2835.c +0
-0
drivers/pinctrl/bcm/pinctrl-bcm2835.c static int bcm2835_pinctrl_probe(struct platform_device *pdev) · line 1252
Quoted 9 lines
drivers/pinctrl/bcm/pinctrl-bcm2835.c +6
-0@@ -1244,6 +1244,18 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev)raw_spin_lock_init (&pc->irq_lock[i]); } + pc->pctl_desc = *pdata->pctl_desc; + pc->pctl_dev =devm_pinctrl_register (dev, &pc->pctl_desc, pc); +if (IS_ERR (pc->pctl_dev)) { +gpiochip_remove (&pc->gpio_chip); +return PTR_ERR (pc->pctl_dev); + }
You do gpiochip_remove(), even when it was not added.
drivers/pinctrl/bcm/pinctrl-bcm2835.c static int bcm2835_pinctrl_probe(struct platform_device *pdev) · line 1269
Quoted 9 lines
drivers/pinctrl/bcm/pinctrl-bcm2835.c +3
-1@@ -1251,8 +1263,10 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev) girq->parents =devm_kcalloc (dev,BCM2835_NUM_IRQS ,sizeof (*girq->parents),GFP_KERNEL ); -if (!girq->parents) +if (!girq->parents) { +pinctrl_remove_gpio_range (pc->pctl_dev, &pc->gpio_range);return -ENOMEM ; + }
And yes, adding the removes here makes sense, but it looks like some are missing (in 5.10).
Something like this?
Best regards,
Pavel
drivers/pinctrl/bcm/pinctrl-bcm2835.c +15 -9
@@ -1247,7 +1247,6 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev) pc->pctl_desc = *pdata->pctl_desc; pc->pctl_dev =devm_pinctrl_register (dev, &pc->pctl_desc, pc);if (IS_ERR (pc->pctl_dev)) { -gpiochip_remove (&pc->gpio_chip);return PTR_ERR (pc->pctl_dev); }
@@ -1264,16 +1263,18 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev)sizeof (*girq->parents), GFP_KERNEL);if (!girq->parents) { -pinctrl_remove_gpio_range (pc->pctl_dev, &pc->gpio_range); -return -ENOMEM ; + err = -ENOMEM ; + goto remove_gpio; }if (is_7211) { pc->wake_irq =devm_kcalloc (dev,BCM2835_NUM_IRQS ,sizeof (*pc->wake_irq),GFP_KERNEL ); -if (!pc->wake_irq) -return -ENOMEM ; +if (!pc->wake_irq) { + err = -ENOMEM ; + goto remove_gpio; + } }/*
@@ -1297,8 +1298,10 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev) len =strlen (dev_name (pc->dev)) +16 ; name =devm_kzalloc (pc->dev, len,GFP_KERNEL ); -if (!name) -return -ENOMEM ; +if (!name) { + err = -ENOMEM ; + goto remove_gpio; + }snprintf (name, len,"%s:bank%d" ,dev_name (pc->dev), i);
@@ -1317,11 +1320,14 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev) err =gpiochip_add_data (&pc->gpio_chip, pc);if (err) {dev_err (dev,"could not add GPIO chip\n" ); -pinctrl_remove_gpio_range (pc->pctl_dev, &pc->gpio_range); -return err; + goto remove_gpio; }return 0 ; + +remove_gpio: +pinctrl_remove_gpio_range (pc->pctl_dev, &pc->gpio_range); +return err; }static struct platform_driver bcm2835_pinctrl_driver = {
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Greg Kroah-Hartman
maintainerPATCH 30/76 hwmon: (lm90) Fix usage of CONFIG2 register in detect function
In reply to Greg Kroah-HartmanFrom: Guenter Roeck <[email protected]>
[ Upstream commit fce15c45d3fbd9fc1feaaf3210d8e3f8b33dfd3a ]
The detect function had a comment "Make compiler happy" when id did not read the second configuration register. As it turns out, the code was checking the contents of this register for manufacturer ID 0xA1 (NXP Semiconductor/Philips), but never actually read the register. So it wasn't surprising that the compiler complained, and it indeed had a point. Fix the code to read the register contents for manufacturer ID 0xa1.
At the same time, the code was reading the register for manufacturer ID 0x41 (Analog Devices), but it was not using the results. In effect it was just checking if reading the register returned an error. That doesn't really add much if any value, so stop doing that.
--- drivers/hwmon/lm90.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)
drivers/hwmon/lm90.c +2 -3
@@ -1438,12 +1438,11 @@ static int lm90_detect(struct i2c_client *client,if (man_id <0 || chip_id <0 || config1 <0 || convrate <0 )return -ENODEV ; -if (man_id ==0x01 || man_id ==0x5C || man_id ==0x41 ) { +if (man_id ==0x01 || man_id ==0x5C || man_id ==0xA1 ) { config2 =i2c_smbus_read_byte_data (client,LM90_REG_R_CONFIG2 );if (config2 <0 )return -ENODEV ; - }else - config2 =0 ;/* Make compiler happy */ + }if ((address ==0x4C || address ==0x4D ) && man_id ==0x01 ) {/* National Semiconductor */
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 31/76 hwmon: (lm90) Add basic support for TI TMP461
In reply to Greg Kroah-HartmanFrom: Guenter Roeck <[email protected]>
[ Upstream commit f8344f7693a25d9025a59d164450b50c6f5aa3c0 ]
TMP461 is almost identical to TMP451 and was actually detected as TMP451 with the existing lm90 driver if its I2C address is 0x4c. Add support for it to the lm90 driver. At the same time, improve the chip detection function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations"). TMP461 does not support word operations on temperature registers, which causes bad temperature readings with the tmp401 driver. The lm90 driver does not perform word operations on temperature registers and thus does not have this problem.
Support is listed as basic because TMP461 supports a sensor resolution of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125 degrees C. Also, the TMP461 supports negative temperatures with its default temperature range, which is not the case for similar chips supported by the lm90 and the tmp401 drivers. Those limitations will be addressed with follow-up patches.
--- Documentation/hwmon/lm90.rst | 10 +++++++ drivers/hwmon/Kconfig | 2 +- drivers/hwmon/lm90.c | 54 ++++++++++++++++++++++++++---------- 3 files changed, 50 insertions(+), 16 deletions(-)
Documentation/hwmon/lm90.rst +10 -0
@@ -265,6 +265,16 @@ Supported chips: https://www.ti.com/litv/pdf/sbos686 + * Texas Instruments TMP461 + + Prefix: 'tmp461' + + Addresses scanned: I2C 0x48 through 0x4F + + Datasheet: Publicly available at TI website + + https://www.ti.com/lit/gpn/tmp461 + Author: Jean Delvare <[email protected]>
drivers/hwmon/Kconfig +1 -1
@@ -1275,7 +1275,7 @@ config SENSORS_LM90 Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6654, MAX6657, MAX6658, MAX6659, MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, ON Semiconductor NCT1008, Winbond/Nuvoton W83L771W/G/AWG/ASG, - Philips SA56004, GMT G781, and Texas Instruments TMP451 + Philips SA56004, GMT G781, Texas Instruments TMP451 and TMP461 sensor chips. This driver can also be built as a module. If so, the module
drivers/hwmon/lm90.c +39 -15
100 lines not on this page · raw message
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 32/76 hwmon: (lm90) Introduce flag indicating extended temperature support
In reply to Greg Kroah-HartmanFrom: Guenter Roeck <[email protected]>
[ Upstream commit f347e249fcf920ad6974cbd898e2ec0b366a1c34 ]
A flag indicating extended temperature support makes it easier to add support for additional chips with this functionality.
--- drivers/hwmon/lm90.c | 21 +++++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-)
drivers/hwmon/lm90.c +11 -10
@@ -186,7 +186,8 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,#define LM90_HAVE_EMERGENCY_ALARM (1 << 5)/* emergency alarm */ #define LM90_HAVE_TEMP3 (1 << 6)/* 3rd temperature sensor */ #define LM90_HAVE_BROKEN_ALERT (1 << 7)/* Broken alert */ -#define LM90_PAUSE_FOR_CONFIG (1 << 8)/* Pause conversion for config */ +#define LM90_HAVE_EXTENDED_TEMP (1 << 8)/* extended temperature support*/ +#define LM90_PAUSE_FOR_CONFIG (1 << 9)/* Pause conversion for config */ /* LM90 status */ #define LM90_STATUS_LTHRM (1 << 0)/* local THERM limit tripped */
@@ -359,7 +360,7 @@ static const struct lm90_params lm90_params[] = { }, [adt7461] = { .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT - | LM90_HAVE_BROKEN_ALERT, + | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP, .alert_alarms = 0x7c, .max_convrate = 10, },
@@ -431,7 +432,7 @@ static const struct lm90_params lm90_params[] = { }, [tmp451] = { .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT - | LM90_HAVE_BROKEN_ALERT, + | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP, .alert_alarms = 0x7c, .max_convrate = 9, .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
@@ -1013,7 +1014,7 @@ static int lm90_get_temp11(struct lm90_data *data, int index)s16 temp11 = data->temp11[index];int temp; -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) temp =temp_from_u16_adt7461 (data, temp11);else if (data->kind == max6646) temp =temp_from_u16 (temp11);
@@ -1047,7 +1048,7 @@ static int lm90_set_temp11(struct lm90_data *data, int index, long val)if (data->kind == lm99 && index <=2 ) val -=16000 ; -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) data->temp11[index] =temp_to_u16_adt7461 (data, val);else if (data->kind == max6646) data->temp11[index] =temp_to_u8 (val) <<8 ;
@@ -1074,7 +1075,7 @@ static int lm90_get_temp8(struct lm90_data *data, int index)s8 temp8 = data->temp8[index];int temp; -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) temp =temp_from_u8_adt7461 (data, temp8);else if (data->kind == max6646) temp =temp_from_u8 (temp8);
@@ -1107,7 +1108,7 @@ static int lm90_set_temp8(struct lm90_data *data, int index, long val)if (data->kind == lm99 && index ==3 ) val -=16000 ; -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) data->temp8[index] =temp_to_u8_adt7461 (data, val);else if (data->kind == max6646) data->temp8[index] =temp_to_u8 (val);
@@ -1125,7 +1126,7 @@ static int lm90_get_temphyst(struct lm90_data *data, int index) {int temp; -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) temp =temp_from_u8_adt7461 (data, data->temp8[index]);else if (data->kind == max6646) temp =temp_from_u8 (data->temp8[index]);
@@ -1145,7 +1146,7 @@ static int lm90_set_temphyst(struct lm90_data *data, long val)int temp;int err; -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) temp =temp_from_u8_adt7461 (data, data->temp8[LOCAL_CRIT ]);else if (data->kind == max6646) temp =temp_from_u8 (data->temp8[LOCAL_CRIT ]);
@@ -1698,7 +1699,7 @@ static int lm90_init_client(struct i2c_client *client, struct lm90_data *data)lm90_set_convrate (client, data,500 );/* 500ms; 2Hz conversion rate */ /* Check Temperature Range Select */ -if (data->kind == adt7461 || data->kind == tmp451) { +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) {if (config &0x04 ) data->flags |=LM90_FLAG_ADT7461_EXT ; }
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 33/76 hwmon: (lm90) Drop critical attribute support for MAX6654
In reply to Greg Kroah-HartmanFrom: Guenter Roeck <[email protected]>
[ Upstream commit 16ba51b5dcd3f6dde2e51d5ccc86313119dcf889 ]
Tests with a real chip and a closer look into the datasheet show that MAX6654 does not support CRIT/THERM/OVERTEMP limits, so drop support of the respective attributes for this chip.
Introduce LM90_HAVE_CRIT flag and use it to instantiate critical limit attributes to solve the problem.
--- drivers/hwmon/lm90.c | 86 +++++++++++++++++++++++++------------------- 1 file changed, 49 insertions(+), 37 deletions(-)
drivers/hwmon/lm90.c +49 -37
@@ -35,13 +35,14 @@* explicitly as max6659, or if its address is not 0x4c. * These chips lack the remote temperature offset feature. * -* This driver also supports the MAX6654 chip made by Maxim. This chip can -* be at 9 different addresses, similar to MAX6680/MAX6681. The MAX6654 is -* otherwise similar to MAX6657/MAX6658/MAX6659. Extended range is available -* by setting the configuration register accordingly, and is done during -* initialization. Extended precision is only available at conversion rates -* of 1 Hz and slower. Note that extended precision is not enabled by -* default, as this driver initializes all chips to 2 Hz by design. +* This driver also supports the MAX6654 chip made by Maxim. This chip can be +* at 9 different addresses, similar to MAX6680/MAX6681. The MAX6654 is similar +* to MAX6657/MAX6658/MAX6659, but does not support critical temperature +* limits. Extended range is available by setting the configuration register +* accordingly, and is done during initialization. Extended precision is only +* available at conversion rates of 1 Hz and slower. Note that extended +* precision is not enabled by default, as this driver initializes all chips +* to 2 Hz by design. * * This driver also supports the MAX6646, MAX6647, MAX6648, MAX6649 and * MAX6692 chips made by Maxim. These are again similar to the LM86,
@@ -188,6 +189,7 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,#define LM90_HAVE_BROKEN_ALERT (1 << 7)/* Broken alert */ #define LM90_HAVE_EXTENDED_TEMP (1 << 8)/* extended temperature support*/ #define LM90_PAUSE_FOR_CONFIG (1 << 9)/* Pause conversion for config */ +#define LM90_HAVE_CRIT (1 << 10)/* Chip supports CRIT/OVERT register */ /* LM90 status */ #define LM90_STATUS_LTHRM (1 << 0)/* local THERM limit tripped */
@@ -354,38 +356,43 @@ struct lm90_params {static const struct lm90_params lm90_params[] = { [adm1032] = { .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT - |LM90_HAVE_BROKEN_ALERT , + |LM90_HAVE_BROKEN_ALERT |LM90_HAVE_CRIT , .alert_alarms =0x7c , .max_convrate =10 , }, [adt7461] = { .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT - |LM90_HAVE_BROKEN_ALERT |LM90_HAVE_EXTENDED_TEMP , + |LM90_HAVE_BROKEN_ALERT |LM90_HAVE_EXTENDED_TEMP + |LM90_HAVE_CRIT , .alert_alarms =0x7c , .max_convrate =10 , }, [g781] = { .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT - |LM90_HAVE_BROKEN_ALERT , + |LM90_HAVE_BROKEN_ALERT |LM90_HAVE_CRIT , .alert_alarms =0x7c , .max_convrate =8 , }, [lm86] = { - .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT , + .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT + |LM90_HAVE_CRIT , .alert_alarms =0x7b , .max_convrate =9 , }, [lm90] = { - .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT , + .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT + |LM90_HAVE_CRIT , .alert_alarms =0x7b , .max_convrate =9 , }, [lm99] = { - .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT , + .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT + |LM90_HAVE_CRIT , .alert_alarms =0x7b , .max_convrate =9 , }, [max6646] = { + .flags =LM90_HAVE_CRIT , .alert_alarms =0x7c , .max_convrate =6 , .reg_local_ext =MAX6657_REG_R_LOCAL_TEMPL ,
@@ -396,50 +403,50 @@ static const struct lm90_params lm90_params[] = { .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, }, [max6657] = { - .flags = LM90_PAUSE_FOR_CONFIG, + .flags = LM90_PAUSE_FOR_CONFIG | LM90_HAVE_CRIT, .alert_alarms = 0x7c, .max_convrate = 8, .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, }, [max6659] = { - .flags = LM90_HAVE_EMERGENCY, + .flags = LM90_HAVE_EMERGENCY | LM90_HAVE_CRIT, .alert_alarms = 0x7c, .max_convrate = 8, .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, }, [max6680] = { - .flags = LM90_HAVE_OFFSET, + .flags = LM90_HAVE_OFFSET | LM90_HAVE_CRIT, .alert_alarms = 0x7c, .max_convrate = 7, }, [max6696] = { .flags =LM90_HAVE_EMERGENCY - | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3, + | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3 | LM90_HAVE_CRIT, .alert_alarms = 0x1c7c, .max_convrate = 6, .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, }, [w83l771] = { - .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT, + .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_CRIT, .alert_alarms = 0x7c, .max_convrate = 8, }, [sa56004] = { - .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT, + .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_CRIT, .alert_alarms = 0x7b, .max_convrate = 9, .reg_local_ext = SA56004_REG_R_LOCAL_TEMPL, }, [tmp451] = { .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT - | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP, + | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP | LM90_HAVE_CRIT, .alert_alarms = 0x7c, .max_convrate = 9, .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL, }, [tmp461] = { .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT - | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP, + | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP | LM90_HAVE_CRIT, .alert_alarms = 0x7c, .max_convrate = 9, .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
@@ -667,20 +674,22 @@ static int lm90_update_limits(struct device *dev)struct i2c_client *client = data->client;int val; - val =lm90_read_reg (client,LM90_REG_R_LOCAL_CRIT ); -if (val <0 ) -return val; - data->temp8[LOCAL_CRIT ] = val; +if (data->flags &LM90_HAVE_CRIT ) { + val =lm90_read_reg (client,LM90_REG_R_LOCAL_CRIT ); +if (val <0 ) +return val; + data->temp8[LOCAL_CRIT ] = val; - val =lm90_read_reg (client,LM90_REG_R_REMOTE_CRIT ); -if (val <0 ) -return val; - data->temp8[REMOTE_CRIT ] = val; + val =lm90_read_reg (client,LM90_REG_R_REMOTE_CRIT ); +if (val <0 ) +return val; + data->temp8[REMOTE_CRIT ] = val; - val =lm90_read_reg (client,LM90_REG_R_TCRIT_HYST ); -if (val <0 ) -return val; - data->temp_hyst = val; + val =lm90_read_reg (client,LM90_REG_R_TCRIT_HYST ); +if (val <0 ) +return val; + data->temp_hyst = val; + } val =lm90_read_reg (client,LM90_REG_R_REMOTE_LOWH );if (val <0 )
@@ -1866,11 +1875,14 @@ static int lm90_probe(struct i2c_client *client) info->config = data->channel_config; data->channel_config[0 ] =HWMON_T_INPUT |HWMON_T_MIN |HWMON_T_MAX | -HWMON_T_CRIT |HWMON_T_CRIT_HYST |HWMON_T_MIN_ALARM | -HWMON_T_MAX_ALARM |HWMON_T_CRIT_ALARM ; +HWMON_T_MIN_ALARM |HWMON_T_MAX_ALARM ; data->channel_config[1 ] =HWMON_T_INPUT |HWMON_T_MIN |HWMON_T_MAX | -HWMON_T_CRIT |HWMON_T_CRIT_HYST |HWMON_T_MIN_ALARM | -HWMON_T_MAX_ALARM |HWMON_T_CRIT_ALARM |HWMON_T_FAULT ; +HWMON_T_MIN_ALARM |HWMON_T_MAX_ALARM |HWMON_T_FAULT ; + +if (data->flags &LM90_HAVE_CRIT ) { + data->channel_config[0 ] |=HWMON_T_CRIT |HWMON_T_CRIT_ALARM |HWMON_T_CRIT_HYST ; + data->channel_config[1 ] |=HWMON_T_CRIT |HWMON_T_CRIT_ALARM |HWMON_T_CRIT_HYST ; + }if (data->flags &LM90_HAVE_OFFSET ) data->channel_config[1 ] |=HWMON_T_OFFSET ;
Signature · 1 line
2.34.1
Greg Kroah-Hartman
maintainerPATCH 34/76 ALSA: jack: Check the return value of kstrdup()
In reply to Greg Kroah-HartmanFrom: Xiaoke Wang <[email protected]>
commit c01c1db1dc632edafb0dff32d40daf4f9c1a4e19 upstream.
kstrdup() can return NULL, it is better to check the return value of it.
--- sound/core/jack.c | 4 ++++ 1 file changed, 4 insertions(+)
sound/core/jack.c +4 -0
@@ -220,6 +220,10 @@ int snd_jack_new(struct snd_card *card,return -ENOMEM ; jack->id =kstrdup (id,GFP_KERNEL ); +if (jack->id ==NULL ) { +kfree (jack); +return -ENOMEM ; + }/* don't creat input device for phantom jack */ if (!phantom_jack) {
Greg Kroah-Hartman
maintainerPATCH 35/76 ALSA: drivers: opl3: Fix incorrect use of vp->state
In reply to Greg Kroah-HartmanFrom: Colin Ian King <[email protected]>
commit 2dee54b289fbc810669a1b2b8a0887fa1c9a14d7 upstream.
Static analysis with scan-build has found an assignment to vp2 that is never used. It seems that the check on vp->state > 0 should be actually on vp2->state instead. Fix this.
This dates back to 2002, I found the offending commit from the git history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit 91e39521bbf6 ("[PATCH] ALSA patch for 2.5.4")
--- sound/drivers/opl3/opl3_midi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
sound/drivers/opl3/opl3_midi.c +1 -1
@@ -398,7 +398,7 @@ void snd_opl3_note_on(void *p, int note, }if (instr_4op) { vp2 = &opl3->voices[voice +3 ]; -if (vp->state >0 ) { +if (vp2->state >0 ) { opl3_reg = reg_side | (OPL3_REG_KEYON_BLOCK + voice_offset +3 ); reg_val = vp->keyon_reg & ~OPL3_KEYON_BIT ;
Greg Kroah-Hartman
maintainerPATCH 36/76 ALSA: hda/realtek: Amp init fixup for HP ZBook 15 G6
In reply to Greg Kroah-HartmanFrom: Bradley Scott <[email protected]>
commit d296a74b7b59ff9116236c17edb25f26935dbf70 upstream.
HP ZBook 15 G6 (SSID 103c:860f) needs the same speaker amplifier initialization as used on several other HP laptops using ALC285.
--- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+)
sound/pci/hda/patch_realtek.c +1 -0
@@ -8599,6 +8599,7 @@ static const struct snd_pci_quirk alc269SND_PCI_QUIRK (0x103c ,0x84da ,"HP OMEN dc0019-ur" ,ALC295_FIXUP_HP_OMEN ),SND_PCI_QUIRK (0x103c ,0x84e7 ,"HP Pavilion 15" ,ALC269_FIXUP_HP_MUTE_LED_MIC3 ),SND_PCI_QUIRK (0x103c ,0x8519 ,"HP Spectre x360 15-df0xxx" ,ALC285_FIXUP_HP_SPECTRE_X360 ), +SND_PCI_QUIRK (0x103c ,0x860f ,"HP ZBook 15 G6" ,ALC285_FIXUP_HP_GPIO_AMP_INIT ),SND_PCI_QUIRK (0x103c ,0x861f ,"HP Elite Dragonfly G1" ,ALC285_FIXUP_HP_GPIO_AMP_INIT ),SND_PCI_QUIRK (0x103c ,0x869d ,"HP" ,ALC236_FIXUP_HP_MUTE_LED ), SND_PCI_QUIRK(0x103c, 0x86c7, "HP Envy AiO 32", ALC274_FIXUP_HP_ENVY_GPIO),
Greg Kroah-Hartman
maintainerPATCH 37/76 ALSA: hda/realtek: Add new alc285-hp-amp-init model
In reply to Greg Kroah-HartmanFrom: Bradley Scott <[email protected]>
commit aa72394667e5cea3547e4c41ddff7ca8c632d764 upstream.
Adds a new "alc285-hp-amp-init" model that can be used to apply the ALC285 HP speaker amplifier initialization fixup to devices that are not already known by passing "hda_model=alc285-hp-amp-init" to the snd-sof-intel-hda-common module or "model=alc285-hp-amp-init" to the snd-hda-intel module, depending on which is being used.
--- Documentation/sound/hd-audio/models.rst | 2 ++ sound/pci/hda/patch_realtek.c | 1 + 2 files changed, 3 insertions(+)
Documentation/sound/hd-audio/models.rst +2 -0
@@ -326,6 +326,8 @@ usi-headset Headset support on USI machines dual-codecs Lenovo laptops with dual codecs +alc285-hp-amp-init + HP laptops which require speaker amplifier initialization (ALC285) ALC680 ======
sound/pci/hda/patch_realtek.c +1 -0
@@ -9061,6 +9061,7 @@ static const struct hda_model_fixup alc2 {.id = ALC287_FIXUP_IDEAPAD_BASS_SPK_AMP, .name = "alc287-ideapad-bass-spk-amp"}, {.id = ALC623_FIXUP_LENOVO_THINKSTATION_P340, .name = "alc623-lenovo-thinkstation-p340"}, {.id = ALC255_FIXUP_ACER_HEADPHONE_AND_MIC, .name = "alc255-acer-headphone-and-mic"}, + {.id = ALC285_FIXUP_HP_GPIO_AMP_INIT, .name = "alc285-hp-amp-init"}, {} };#define ALC225_STANDARD_PINS \
Greg Kroah-Hartman
maintainerPATCH 38/76 ALSA: hda/realtek: Fix quirk for Clevo NJ51CU
In reply to Greg Kroah-HartmanFrom: Werner Sembach <[email protected]>
commit edca7cc4b0accfa69dc032442fe0684e59c691b8 upstream.
The Clevo NJ51CU comes either with the ALC293 or the ALC256 codec, but uses the 0x8686 subproduct id in both cases. The ALC256 codec needs a different quirk for the headset microphone working and and edditional quirk for sound working after suspend and resume.
When waking up from s3 suspend the Coef 0x10 is set to 0x0220 instead of 0x0020 on the ALC256 codec. Setting the value manually makes the sound work again. This patch does this automatically.
[ minor coding style fix by tiwai ]
--- sound/pci/hda/patch_realtek.c | 26 +++++++++++++++++++++++++- 1 file changed, 25 insertions(+), 1 deletion(-)
sound/pci/hda/patch_realtek.c +25 -1
@@ -6492,6 +6492,23 @@ static void alc233_fixup_no_audio_jack(salc_process_coef_fw (codec, alc233_fixup_no_audio_jack_coefs); } +static void alc256_fixup_mic_no_presence_and_resume (struct hda_codec *codec, +const struct hda_fixup *fix, +int action) +{ +/* +* The Clevo NJ51CU comes either with the ALC293 or the ALC256 codec, +* but uses the 0x8686 subproduct id in both cases. The ALC256 codec +* needs an additional quirk for sound working after suspend and resume. +*/ +if (codec->core.vendor_id ==0x10ec0256 ) { +alc_update_coef_idx (codec,0x10 ,1 <<9 ,0 ); +snd_hda_codec_set_pincfg (codec,0x19 ,0x04a11120 ); + }else { +snd_hda_codec_set_pincfg (codec,0x1a ,0x04a1113c ); + } +} +enum {ALC269_FIXUP_GPIO2 ,ALC269_FIXUP_SONY_VAIO ,
@@ -6711,6 +6728,7 @@ enum {ALC256_FIXUP_SET_COEF_DEFAULTS ,ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE ,ALC233_FIXUP_NO_AUDIO_JACK , + ALC256_FIXUP_MIC_NO_PRESENCE_AND_RESUME, }; static const struct hda_fixup alc269_fixups[] = {
@@ -8429,6 +8447,12 @@ static const struct hda_fixup alc269_fix .type = HDA_FIXUP_FUNC, .v.func = alc233_fixup_no_audio_jack, }, + [ALC256_FIXUP_MIC_NO_PRESENCE_AND_RESUME] = { + .type = HDA_FIXUP_FUNC, + .v.func = alc256_fixup_mic_no_presence_and_resume, + .chained = true, + .chain_id =ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC + }, };static const struct snd_pci_quirk alc269_fixup_tbl[] = {
@@ -8767,7 +8791,7 @@ static const struct snd_pci_quirk alc269SND_PCI_QUIRK (0x1558 ,0x8562 ,"Clevo NH[5|7][0-9]RZ[Q]" ,ALC269_FIXUP_DMIC ),SND_PCI_QUIRK (0x1558 ,0x8668 ,"Clevo NP50B[BE]" ,ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE ),SND_PCI_QUIRK (0x1558 ,0x8680 ,"Clevo NJ50LU" ,ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE ), -SND_PCI_QUIRK (0x1558 ,0x8686 ,"Clevo NH50[CZ]U" ,ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE ), +SND_PCI_QUIRK (0x1558 ,0x8686 ,"Clevo NH50[CZ]U" ,ALC256_FIXUP_MIC_NO_PRESENCE_AND_RESUME ),SND_PCI_QUIRK (0x1558 ,0x8a20 ,"Clevo NH55DCQ-Y" ,ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE ),SND_PCI_QUIRK (0x1558 ,0x8a51 ,"Clevo NH70RCQ-Y" ,ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE ), SND_PCI_QUIRK(0x1558, 0x8d50, "Clevo NH55RCQ-M", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
Greg Kroah-Hartman
maintainerPATCH 39/76 ASoC: meson: aiu: Move AIU_I2S_MISC hold setting to aiu-fifo-i2s
In reply to Greg Kroah-HartmanFrom: Martin Blumenstingl <[email protected]>
commit ee907afb0c39a41ee74b862882cfe12820c74b98 upstream.
The out-of-tree vendor driver uses the following approach to set the AIU_I2S_MISC register:
1) write AIU_MEM_I2S_START_PTR and AIU_MEM_I2S_RD_PTR
2) configure AIU_I2S_MUTE_SWAP[15:0]
3) write AIU_MEM_I2S_END_PTR
4) set AIU_I2S_MISC[2] to 1 (documented as: "put I2S interface in hold mode")
5) set AIU_I2S_MISC[4] to 1 (depending on the driver revision it always stays at 1 while for older drivers this bit is unset in step 4)
6) set AIU_I2S_MISC[2] to 0
7) write AIU_MEM_I2S_MASKS
8) toggle AIU_MEM_I2S_CONTROL[0]
9) toggle AIU_MEM_I2S_BUF_CNTL[0]
Move setting the AIU_I2S_MISC[2] bit to aiu_fifo_i2s_hw_params() so it resembles the flow in the vendor kernel more closely. While here also configure AIU_I2S_MISC[4] (documented as: "force each audio data to left or right according to the bit attached with the audio data") similar to how the vendor driver does this. This fixes the infamous and long-standing "machine gun noise" issue (a buffer underrun issue).
--- sound/soc/meson/aiu-encoder-i2s.c | 33 --------------------------------- sound/soc/meson/aiu-fifo-i2s.c | 19 +++++++++++++++++++ 2 files changed, 19 insertions(+), 33 deletions(-)
sound/soc/meson/aiu-encoder-i2s.c +0 -33
@@ -18,7 +18,6 @@#define AIU_RST_SOFT_I2S_FAST BIT(0)#define AIU_I2S_DAC_CFG_MSB_FIRST BIT(2) -#define AIU_I2S_MISC_HOLD_EN BIT(2)#define AIU_CLK_CTRL_I2S_DIV_EN BIT(0)#define AIU_CLK_CTRL_I2S_DIV GENMASK(3, 2)#define AIU_CLK_CTRL_AOCLK_INVERT BIT(6)
@@ -36,37 +35,6 @@ static void aiu_encoder_i2s_divider_enab enable ? AIU_CLK_CTRL_I2S_DIV_EN : 0); } -static void aiu_encoder_i2s_hold (struct snd_soc_component *component, -bool enable) -{ -snd_soc_component_update_bits (component,AIU_I2S_MISC , -AIU_I2S_MISC_HOLD_EN , - enable ?AIU_I2S_MISC_HOLD_EN :0 ); -} - -static int aiu_encoder_i2s_trigger (struct snd_pcm_substream *substream,int cmd, -struct snd_soc_dai *dai) -{ -struct snd_soc_component *component = dai->component; - -switch (cmd) { -case SNDRV_PCM_TRIGGER_START : -case SNDRV_PCM_TRIGGER_RESUME : -case SNDRV_PCM_TRIGGER_PAUSE_RELEASE : -aiu_encoder_i2s_hold (component, false); -return 0 ; - -case SNDRV_PCM_TRIGGER_STOP : -case SNDRV_PCM_TRIGGER_SUSPEND : -case SNDRV_PCM_TRIGGER_PAUSE_PUSH : -aiu_encoder_i2s_hold (component, true); -return 0 ; - -default : -return -EINVAL ; - } -} -static int aiu_encoder_i2s_setup_desc (struct snd_soc_component *component,struct snd_pcm_hw_params *params) {
@@ -353,7 +321,6 @@ static void aiu_encoder_i2s_shutdown(str }const struct snd_soc_dai_ops aiu_encoder_i2s_dai_ops = { - .trigger = aiu_encoder_i2s_trigger, .hw_params = aiu_encoder_i2s_hw_params, .hw_free = aiu_encoder_i2s_hw_free, .set_fmt = aiu_encoder_i2s_set_fmt,
sound/soc/meson/aiu-fifo-i2s.c +19 -0
@@ -20,6 +20,8 @@#define AIU_MEM_I2S_CONTROL_MODE_16BIT BIT(6)#define AIU_MEM_I2S_BUF_CNTL_INIT BIT(0)#define AIU_RST_SOFT_I2S_FAST BIT(0) +#define AIU_I2S_MISC_HOLD_EN BIT(2) +#define AIU_I2S_MISC_FORCE_LEFT_RIGHT BIT(4)#define AIU_FIFO_I2S_BLOCK 256
@@ -90,6 +92,10 @@ static int aiu_fifo_i2s_hw_params(structunsigned int val;int ret; +snd_soc_component_update_bits (component,AIU_I2S_MISC , +AIU_I2S_MISC_HOLD_EN , +AIU_I2S_MISC_HOLD_EN ); + ret =aiu_fifo_hw_params (substream, params, dai);if (ret)return ret;
@@ -117,6 +123,19 @@ static int aiu_fifo_i2s_hw_params(structsnd_soc_component_update_bits (component,AIU_MEM_I2S_MASKS ,AIU_MEM_I2S_MASKS_IRQ_BLOCK , val); +/* +* Most (all?) supported SoCs have this bit set by default. The vendor +* driver however sets it manually (depending on the version either +* while un-setting AIU_I2S_MISC_HOLD_EN or right before that). Follow +* the same approach for consistency with the vendor driver. +*/ +snd_soc_component_update_bits (component,AIU_I2S_MISC , +AIU_I2S_MISC_FORCE_LEFT_RIGHT , +AIU_I2S_MISC_FORCE_LEFT_RIGHT ); + +snd_soc_component_update_bits (component,AIU_I2S_MISC , +AIU_I2S_MISC_HOLD_EN ,0 ); +return 0 ; }
Greg Kroah-Hartman
maintainerPATCH 40/76 Input: atmel_mxt_ts - fix double free in mxt_read_info_block
In reply to Greg Kroah-HartmanFrom: José Expósito <[email protected]>
commit 12f247ab590a08856441efdbd351cf2cc8f60a2d upstream.
The "id_buf" buffer is stored in "data->raw_info_block" and freed by "mxt_free_object_table" in case of error.
Return instead of jumping to avoid a double free.
Addresses-Coverity-ID: 1474582 ("Double free")
--- drivers/input/touchscreen/atmel_mxt_ts.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/input/touchscreen/atmel_mxt_ts.c +1 -1
@@ -1839,7 +1839,7 @@ static int mxt_read_info_block(struct mxif (error) {dev_err (&client->dev,"Error %d parsing object table\n" , error);mxt_free_object_table (data); - goto err_free_mem; +return error; } data->object_table = (struct mxt_object *)(id_buf +MXT_OBJECT_START );
Greg Kroah-Hartman
maintainerPATCH 41/76 ipmi: bail out if init_srcu_struct fails
In reply to Greg Kroah-HartmanFrom: Thadeu Lima de Souza Cascardo <[email protected]>
commit 2b5160b12091285c5aca45980f100a9294af7b04 upstream.
In case, init_srcu_struct fails (because of memory allocation failure), we might proceed with the driver initialization despite srcu_struct not being entirely initialized.
Message-Id: <[email protected]>
--- drivers/char/ipmi/ipmi_msghandler.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/char/ipmi/ipmi_msghandler.c +3 -1
@@ -5161,7 +5161,9 @@ static int ipmi_init_msghandler(void)if (initialized) goto out; -init_srcu_struct (&ipmi_interfaces_srcu); + rv =init_srcu_struct (&ipmi_interfaces_srcu); +if (rv) + goto out;timer_setup (&ipmi_timer, ipmi_timeout,0 );mod_timer (&ipmi_timer, jiffies +IPMI_TIMEOUT_JIFFIES );
Greg Kroah-Hartman
maintainerPATCH 42/76 ipmi: ssif: initialize ssif_info->client early
In reply to Greg Kroah-HartmanFrom: Mian Yousaf Kaukab <[email protected]>
commit 34f35f8f14bc406efc06ee4ff73202c6fd245d15 upstream.
During probe ssif_info->client is dereferenced in error path. However, it is set when some of the error checking has already been done. This causes following kernel crash if an error path is taken:
[ 30.645593][ T674] ipmi_ssif 0-000e: ipmi_ssif: Not probing, Interface already present [ 30.657616][ T674] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088 ... [ 30.657723][ T674] pc : __dev_printk+0x28/0xa0 [ 30.657732][ T674] lr : _dev_err+0x7c/0xa0 ... [ 30.657772][ T674] Call trace: [ 30.657775][ T674] __dev_printk+0x28/0xa0 [ 30.657778][ T674] _dev_err+0x7c/0xa0 [ 30.657781][ T674] ssif_probe+0x548/0x900 [ipmi_ssif 62ce4b08badc1458fd896206d9ef69a3c31f3d3e] [ 30.657791][ T674] i2c_device_probe+0x37c/0x3c0
...
Initialize ssif_info->client before any error path can be taken. Clear i2c_client data in the error path to prevent the dangling pointer from leaking.
Message-Id: <[email protected]>
--- drivers/char/ipmi/ipmi_ssif.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/char/ipmi/ipmi_ssif.c +4 -3
@@ -1700,6 +1700,9 @@ static int ssif_probe(struct i2c_client } } + ssif_info->client = client; +i2c_set_clientdata (client, ssif_info); + rv =ssif_check_and_remove (client, ssif_info);/* If rv is 0 and addr source is not SI_ACPI, continue probing */ if (!rv && ssif_info->addr_source ==SI_ACPI ) {
@@ -1720,9 +1723,6 @@ static int ssif_probe(struct i2c_clientipmi_addr_src_to_str (ssif_info->addr_source), client->addr, client->adapter->name, slave_addr); - ssif_info->client = client; -i2c_set_clientdata (client, ssif_info); -/* Now check for system interface capabilities */ msg[0 ] =IPMI_NETFN_APP_REQUEST <<2 ; msg[1 ] =IPMI_GET_SYSTEM_INTERFACE_CAPABILITIES_CMD ;
@@ -1922,6 +1922,7 @@ static int ssif_probe(struct i2c_clientdev_err (&ssif_info->client->dev,"Unable to start IPMI SSIF: %d\n" , rv); +i2c_set_clientdata (client,NULL );kfree (ssif_info); }kfree (resp);
Greg Kroah-Hartman
maintainerPATCH 43/76 ipmi: fix initialization when workqueue allocation fails
In reply to Greg Kroah-HartmanFrom: Thadeu Lima de Souza Cascardo <[email protected]>
commit 75d70d76cb7b927cace2cb34265d68ebb3306b13 upstream.
If the workqueue allocation fails, the driver is marked as not initialized, and timer and panic_notifier will be left registered.
Instead of removing those when workqueue allocation fails, do the workqueue initialization before doing it, and cleanup srcu_struct if it fails.
Message-Id: <[email protected]>
--- drivers/char/ipmi/ipmi_msghandler.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-)
drivers/char/ipmi/ipmi_msghandler.c +9 -6
@@ -5165,20 +5165,23 @@ static int ipmi_init_msghandler(void)if (rv) goto out; -timer_setup (&ipmi_timer, ipmi_timeout,0 ); -mod_timer (&ipmi_timer, jiffies +IPMI_TIMEOUT_JIFFIES ); - -atomic_notifier_chain_register (&panic_notifier_list, &panic_block); - remove_work_wq =create_singlethread_workqueue ("ipmi-msghandler-remove-wq" );if (!remove_work_wq) {pr_err ("unable to create ipmi-msghandler-remove-wq workqueue" ); rv = -ENOMEM ; - goto out; + goto out_wq; } +timer_setup (&ipmi_timer, ipmi_timeout,0 ); +mod_timer (&ipmi_timer, jiffies +IPMI_TIMEOUT_JIFFIES ); + +atomic_notifier_chain_register (&panic_notifier_list, &panic_block); + initialized = true; +out_wq: +if (rv) +cleanup_srcu_struct (&ipmi_interfaces_srcu); out:mutex_unlock (&ipmi_interfaces_mutex);return rv;
Greg Kroah-Hartman
maintainerPATCH 44/76 parisc: Correct completer in lws start
In reply to Greg Kroah-HartmanFrom: John David Anglin <[email protected]>
commit 8f66fce0f46560b9e910787ff7ad0974441c4f9c upstream.
The completer in the "or,ev %r1,%r30,%r30" instruction is reversed, so we are not clipping the LWS number when we are called from a 32-bit process (W=0). We need to nulify the following depdi instruction when the least-significant bit of %r30 is 1.
If the %r20 register is not clipped, a user process could perform a LWS call that would branch to an undefined location in the kernel and potentially crash the machine.
--- arch/parisc/kernel/syscall.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/parisc/kernel/syscall.S +1 -1
@@ -478,7 +478,7 @@ lws_start: extrd,u %r1,PSW_W_BIT,1,%r1 /* sp must be aligned on 4, so deposit the W bit setting into * the bottom of sp temporarily */ - or,ev %r1,%r30,%r30 + or,od %r1,%r30,%r30 /* Clip LWS number to a 32-bit value for 32-bit processes */ depdi 0, 31, 32, %r20
Greg Kroah-Hartman
maintainerPATCH 45/76 parisc: Fix mask used to select futex spinlock
In reply to Greg Kroah-HartmanFrom: John David Anglin <[email protected]>
commit d3a5a68cff47f6eead84504c3c28376b85053242 upstream.
The address bits used to select the futex spinlock need to match those used in the LWS code in syscall.S. The mask 0x3f8 only selects 7 bits. It should select 8 bits.
This change fixes the glibc nptl/tst-cond24 and nptl/tst-cond25 tests.
--- arch/parisc/include/asm/futex.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/parisc/include/asm/futex.h +2 -2
@@ -16,7 +16,7 @@ static inline void _futex_spin_lock_irqsave(u32 __user *uaddr, unsigned long int *flags) {extern u32 lws_lock_start[]; -long index = ((long )uaddr &0x3f8 ) >>1 ; +long index = ((long )uaddr &0x7f8 ) >>1 ;arch_spinlock_t *s = (arch_spinlock_t *)&lws_lock_start[index];local_irq_save (*flags);arch_spin_lock (s);
@@ -26,7 +26,7 @@ static inline void _futex_spin_unlock_irqrestore(u32 __user *uaddr, unsigned long int *flags) {extern u32 lws_lock_start[]; -long index = ((long )uaddr &0x3f8 ) >>1 ; +long index = ((long )uaddr &0x7f8 ) >>1 ;arch_spinlock_t *s = (arch_spinlock_t *)&lws_lock_start[index];arch_spin_unlock (s);local_irq_restore (*flags);
Greg Kroah-Hartman
maintainerPATCH 46/76 tee: handle lookup of shm with reference count 0
In reply to Greg Kroah-HartmanFrom: Jens Wiklander <[email protected]>
commit dfd0743f1d9ea76931510ed150334d571fbab49d upstream.
Since the tee subsystem does not keep a strong reference to its idle shared memory buffers, it races with other threads that try to destroy a shared memory through a close of its dma-buf fd or by unmapping the memory.
In tee_shm_get_from_id() when a lookup in teedev->idr has been successful, it is possible that the tee_shm is in the dma-buf teardown path, but that path is blocked by the teedev mutex. Since we don't have an API to tell if the tee_shm is in the dma-buf teardown path or not we must find another way of detecting this condition.
Fix this by doing the reference counting directly on the tee_shm using a new refcount_t refcount field. dma-buf is replaced by using anon_inode_getfd() instead, this separates the life-cycle of the underlying file from the tee_shm. tee_shm_put() is updated to hold the mutex when decreasing the refcount to 0 and then remove the tee_shm from teedev->idr before releasing the mutex. This means that the tee_shm can never be found unless it has a refcount larger than 0.
--- drivers/tee/tee_shm.c | 171 ++++++++++++++++++------------------------------ include/linux/tee_drv.h | 4 - 2 files changed, 68 insertions(+), 107 deletions(-)
drivers/tee/tee_shm.c +66 -105
@@ -1,11 +1,11 @@// SPDX-License-Identifier: GPL-2.0-only /* -* Copyright (c) 2015-2016, Linaro Limited +* Copyright (c) 2015-2017, 2019-2021 Linaro Limited */ +#include <linux/anon_inodes.h> #include <linux/device.h> -#include <linux/dma-buf.h> -#include <linux/fdtable.h> #include <linux/idr.h> +#include <linux/mm.h> #include <linux/sched.h> #include <linux/slab.h> #include <linux/tee_drv.h>
@@ -28,16 +28,8 @@ static void release_registered_pages(str } } -static void tee_shm_release (struct tee_shm *shm) +static void tee_shm_release (struct tee_device *teedev,struct tee_shm *shm) { -struct tee_device *teedev = shm->ctx->teedev; - -if (shm->flags &TEE_SHM_DMA_BUF ) { -mutex_lock (&teedev->mutex); -idr_remove (&teedev->idr, shm->id); -mutex_unlock (&teedev->mutex); - } -if (shm->flags &TEE_SHM_POOL ) {struct tee_shm_pool_mgr *poolm;
@@ -64,45 +56,6 @@ static void tee_shm_release(struct tee_stee_device_put (teedev); } -static struct sg_table *tee_shm_op_map_dma_buf (struct dma_buf_attachment - *attach,enum dma_data_direction dir) -{ -return NULL ; -} - -static void tee_shm_op_unmap_dma_buf (struct dma_buf_attachment *attach, -struct sg_table *table, -enum dma_data_direction dir) -{ -} - -static void tee_shm_op_release (struct dma_buf *dmabuf) -{ -struct tee_shm *shm = dmabuf->priv; - -tee_shm_release (shm); -} - -static int tee_shm_op_mmap (struct dma_buf *dmabuf,struct vm_area_struct *vma) -{ -struct tee_shm *shm = dmabuf->priv; -size_t size = vma->vm_end - vma->vm_start; - -/* Refuse sharing shared memory provided by application */ -if (shm->flags &TEE_SHM_USER_MAPPED ) -return -EINVAL ; - -return remap_pfn_range (vma, vma->vm_start, shm->paddr >>PAGE_SHIFT , - size, vma->vm_page_prot); -} - -static const struct dma_buf_ops tee_shm_dma_buf_ops = { - .map_dma_buf = tee_shm_op_map_dma_buf, - .unmap_dma_buf = tee_shm_op_unmap_dma_buf, - .release = tee_shm_op_release, - .mmap = tee_shm_op_mmap, -}; -struct tee_shm *tee_shm_alloc (struct tee_context *ctx,size_t size,u32 flags) {struct tee_device *teedev = ctx->teedev;
@@ -137,6 +90,7 @@ struct tee_shm *tee_shm_alloc(struct tee goto err_dev_put; } +refcount_set (&shm->refcount,1 ); shm->flags = flags |TEE_SHM_POOL ; shm->ctx = ctx;if (flags &TEE_SHM_DMA_BUF )
@@ -150,10 +104,7 @@ struct tee_shm *tee_shm_alloc(struct tee goto err_kfree; } -if (flags &TEE_SHM_DMA_BUF ) { -DEFINE_DMA_BUF_EXPORT_INFO (exp_info); -mutex_lock (&teedev->mutex); shm->id =idr_alloc (&teedev->idr, shm,1 ,0 ,GFP_KERNEL );mutex_unlock (&teedev->mutex);
@@ -161,28 +112,11 @@ struct tee_shm *tee_shm_alloc(struct tee ret =ERR_PTR (shm->id); goto err_pool_free; } - - exp_info.ops = &tee_shm_dma_buf_ops; - exp_info.size = shm->size; - exp_info.flags =O_RDWR ; - exp_info.priv = shm; - - shm->dmabuf =dma_buf_export (&exp_info); -if (IS_ERR (shm->dmabuf)) { - ret =ERR_CAST (shm->dmabuf); - goto err_rem; - } }teedev_ctx_get (ctx);return shm; -err_rem: -if (flags &TEE_SHM_DMA_BUF ) { -mutex_lock (&teedev->mutex); -idr_remove (&teedev->idr, shm->id); -mutex_unlock (&teedev->mutex); - } err_pool_free: poolm->ops->free (poolm, shm); err_kfree:
@@ -243,6 +177,7 @@ struct tee_shm *tee_shm_register(struct goto err; } +refcount_set (&shm->refcount,1 ); shm->flags = flags |TEE_SHM_REGISTER ; shm->ctx = ctx; shm->id =-1 ;
@@ -303,22 +238,6 @@ struct tee_shm *tee_shm_register(struct goto err; } -if (flags &TEE_SHM_DMA_BUF ) { -DEFINE_DMA_BUF_EXPORT_INFO (exp_info); - - exp_info.ops = &tee_shm_dma_buf_ops; - exp_info.size = shm->size; - exp_info.flags =O_RDWR ; - exp_info.priv = shm; - - shm->dmabuf =dma_buf_export (&exp_info); -if (IS_ERR (shm->dmabuf)) { - ret =ERR_CAST (shm->dmabuf); - teedev->desc->ops->shm_unregister (ctx, shm); - goto err; - } - } -return shm; err:if (shm) {
@@ -336,6 +255,35 @@ err: }EXPORT_SYMBOL_GPL (tee_shm_register); +static int tee_shm_fop_release (struct inode *inode,struct file *filp) +{ +tee_shm_put (filp->private_data); +return 0 ; +} + +static int tee_shm_fop_mmap (struct file *filp,struct vm_area_struct *vma) +{ +struct tee_shm *shm = filp->private_data; +size_t size = vma->vm_end - vma->vm_start; + +/* Refuse sharing shared memory provided by application */ +if (shm->flags &TEE_SHM_USER_MAPPED ) +return -EINVAL ; + +/* check for overflowing the buffer's size */ +if (vma->vm_pgoff +vma_pages (vma) > shm->size >>PAGE_SHIFT ) +return -EINVAL ; + +return remap_pfn_range (vma, vma->vm_start, shm->paddr >>PAGE_SHIFT , + size, vma->vm_page_prot); +} + +static const struct file_operations tee_shm_fops = { + .owner =THIS_MODULE , + .release = tee_shm_fop_release, + .mmap = tee_shm_fop_mmap, +}; +/** * tee_shm_get_fd() - Increase reference count and return file descriptor * @shm: Shared memory handle
@@ -348,10 +296,11 @@ int tee_shm_get_fd(struct tee_shm *shm)if (!(shm->flags &TEE_SHM_DMA_BUF ))return -EINVAL ; -get_dma_buf (shm->dmabuf); - fd =dma_buf_fd (shm->dmabuf,O_CLOEXEC ); +/* matched by tee_shm_put() in tee_shm_op_release() */ +refcount_inc (&shm->refcount); + fd =anon_inode_getfd ("tee_shm" , &tee_shm_fops, shm,O_RDWR );if (fd <0 ) -dma_buf_put (shm->dmabuf); +tee_shm_put (shm);return fd; }
@@ -361,17 +310,7 @@ int tee_shm_get_fd(struct tee_shm *shm)*/ void tee_shm_free (struct tee_shm *shm) { -/* -* dma_buf_put() decreases the dmabuf reference counter and will -* call tee_shm_release() when the last reference is gone. -* -* In the case of driver private memory we call tee_shm_release -* directly instead as it doesn't have a reference counter. -*/ -if (shm->flags &TEE_SHM_DMA_BUF ) -dma_buf_put (shm->dmabuf); -else -tee_shm_release (shm); +tee_shm_put (shm); }EXPORT_SYMBOL_GPL (tee_shm_free);
@@ -478,10 +417,15 @@ struct tee_shm *tee_shm_get_from_id(stru teedev = ctx->teedev;mutex_lock (&teedev->mutex); shm =idr_find (&teedev->idr, id); +/* +* If the tee_shm was found in the IDR it must have a refcount +* larger than 0 due to the guarantee in tee_shm_put() below. So +* it's safe to use refcount_inc(). +*/ if (!shm || shm->ctx != ctx) shm =ERR_PTR (-EINVAL ); -else if (shm->flags &TEE_SHM_DMA_BUF ) -get_dma_buf (shm->dmabuf); +else +refcount_inc (&shm->refcount);mutex_unlock (&teedev->mutex);return shm; }
@@ -493,7 +437,24 @@ EXPORT_SYMBOL_GPL(tee_shm_get_from_id);*/ void tee_shm_put (struct tee_shm *shm) { -if (shm->flags &TEE_SHM_DMA_BUF ) -dma_buf_put (shm->dmabuf); +struct tee_device *teedev = shm->ctx->teedev; +bool do_release = false; + +mutex_lock (&teedev->mutex); +if (refcount_dec_and_test (&shm->refcount)) { +/* +* refcount has reached 0, we must now remove it from the +* IDR before releasing the mutex. This will guarantee that +* the refcount_inc() in tee_shm_get_from_id() never starts +* from 0. +*/ +if (shm->flags &TEE_SHM_DMA_BUF ) +idr_remove (&teedev->idr, shm->id); + do_release = true; + } +mutex_unlock (&teedev->mutex); + +if (do_release) +tee_shm_release (teedev, shm); }EXPORT_SYMBOL_GPL (tee_shm_put);
include/linux/tee_drv.h +2 -2
@@ -195,7 +195,7 @@ int tee_session_calc_client_uuid(uuid_t* @offset: offset of buffer in user space * @pages: locked pages from userspace * @num_pages: number of locked pages -* @dmabuf: dmabuf used to for exporting to user space +* @refcount: reference counter * @flags: defined by TEE_SHM_* in tee_drv.h * @id: unique id of a shared memory object on this device *
@@ -210,7 +210,7 @@ struct tee_shm {unsigned int offset;struct page **pages;size_t num_pages; -struct dma_buf *dmabuf; +refcount_t refcount;u32 flags;int id; };
Greg Kroah-Hartman
maintainerPATCH 47/76 x86/pkey: Fix undefined behaviour with PKRU_WD_BIT
In reply to Greg Kroah-HartmanFrom: Andrew Cooper <[email protected]>
commit 57690554abe135fee81d6ac33cc94d75a7e224bb upstream.
Both __pkru_allows_write() and arch_set_user_pkey_access() shift PKRU_WD_BIT (a signed constant) by up to 30 bits, hitting the sign bit.
Use unsigned constants instead.
Clearly pkey 15 has not been used in combination with UBSAN yet.
Noticed by code inspection only. I can't actually provoke the compiler into generating incorrect logic as far as this shift is concerned.
[
dhansen: add stable@ tag, plus minor changelog massaging,
For anyone doing backports, these #defines were in arch/x86/include/asm/pgtable.h before 784a46618f6.
]
--- arch/x86/include/asm/pgtable.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/x86/include/asm/pgtable.h +2 -2
@@ -1360,8 +1360,8 @@ static inline pmd_t pmd_swp_clear_uffd_w }#endif /* CONFIG_HAVE_ARCH_USERFAULTFD_WP */ -#define PKRU_AD_BIT 0x1 -#define PKRU_WD_BIT 0x2 +#define PKRU_AD_BIT 0x1u +#define PKRU_WD_BIT 0x2u#define PKRU_BITS_PER_PKEY 2#ifdef CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS
Greg Kroah-Hartman
maintainerPATCH 48/76 platform/x86: intel_pmc_core: fix memleak on registration failure
In reply to Greg Kroah-HartmanFrom: Johan Hovold <[email protected]>
commit 26a8b09437804fabfb1db080d676b96c0de68e7c upstream.
In case device registration fails during module initialisation, the platform device structure needs to be freed using platform_device_put() to properly free all resources (e.g. the device name).
--- drivers/platform/x86/intel_pmc_core_pltdrv.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/platform/x86/intel_pmc_core_pltdrv.c +1 -1
@@ -65,7 +65,7 @@ static int __init pmc_core_platform_init retval =platform_device_register (pmc_core_device);if (retval) -kfree (pmc_core_device); +platform_device_put (pmc_core_device);return retval; }
Re: [PATCH 5.10 48/76] platform/x86: intel_pmc_core: fix memleak on registration failure
Hi!
Quoted 8 lines · Greg Kroah-Hartman
From: Johan Hovold <[email protected]>
commit
26a8b09437804fabfb1db080d676b96c0de68e7cupstream.In case device registration fails during module initialisation, the platform device structure needs to be freed using
platform_device_put()to properly free all resources (e.g. the device name).
Does it? What exactly was leaking here?
drivers/platform/x86/intel_pmc_core_pltdrv.c static int __init pmc_core_platform_init · line 69
Quoted 8 lines
+++
b/drivers/platform/x86/intel_pmc_core_pltdrv.cdrivers/platform/x86/intel_pmc_core_pltdrv.c +1
-1@@ -65,7 +65,7 @@ static int __init pmc_core_platform_init retval =platform_device_register (pmc_core_device);if (retval) -kfree (pmc_core_device); +platform_device_put (pmc_core_device);
This is strange. Failing registration should have no effects that need to be undone.
Best regards,
Pavel
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Greg Kroah-Hartman
maintainerRe: [PATCH 5.10 48/76] platform/x86: intel_pmc_core: fix memleak on registration failure
Quoted 17 lines · Pavel Machek
Hi!
Quoted 8 lines · Greg Kroah-Hartman
From: Johan Hovold <[email protected]>
commit
26a8b09437804fabfb1db080d676b96c0de68e7cupstream.In case device registration fails during module initialisation, the platform device structure needs to be freed using
platform_device_put()to properly free all resources (e.g. the device name).Does it? What exactly was leaking here?
Quoted 3 lines
+++
b/drivers/platform/x86/intel_pmc_core_pltdrv.c(quoted diff) +0
-0@@ -65,7 +65,7 @@ static int __init pmc_core_platform_init
Quoted 8 lines
drivers/platform/x86/intel_pmc_core_pltdrv.c static int __init pmc_core_platform_init · line 69
Quoted 5 lines
drivers/platform/x86/intel_pmc_core_pltdrv.c +1
-1retval =platform_device_register (pmc_core_device);if (retval) -kfree (pmc_core_device); +platform_device_put (pmc_core_device);This is strange. Failing registration should have no effects that need to be undone.
Sadly, that is not how the driver model has ever worked for various reasons.
greg k-h
Greg Kroah-Hartman
maintainerPATCH 49/76 KVM: VMX: Wake vCPU when delivering posted IRQ even if vCPU == this vCPU
In reply to Greg Kroah-HartmanFrom: Sean Christopherson <[email protected]>
commit fdba608f15e2427419997b0898750a49a735afcb upstream.
Drop a check that guards triggering a posted interrupt on the currently running vCPU, and more importantly guards waking the target vCPU if triggering a posted interrupt fails because the vCPU isn't IN_GUEST_MODE. If a vIRQ is delivered from asynchronous context, the target vCPU can be the currently running vCPU and can also be blocking, in which case skipping kvm_vcpu_wake_up() is effectively dropping what is supposed to be a wake event for the vCPU.
The "do nothing" logic when "vcpu == running_vcpu" mostly works only because the majority of calls to ->deliver_posted_interrupt(), especially when using posted interrupts, come from synchronous KVM context. But if a device is exposed to the guest using vfio-pci passthrough, the VFIO IRQ and vCPU are bound to the same pCPU, and the IRQ is _not_ configured to use posted interrupts, wake events from the device will be delivered to KVM from IRQ context, e.g.
vfio_msihandler()
|
|-> eventfd_signal()
|
|-> ...
|
|-> irqfd_wakeup()
|
|->kvm_arch_set_irq_inatomic()
|
|-> kvm_irq_delivery_to_apic_fast()
|
|-> kvm_apic_set_irq()This also aligns the non-nested and nested usage of triggering posted interrupts, and will allow for additional cleanups.
Message-Id: <[email protected]>
--- arch/x86/kvm/vmx/vmx.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
arch/x86/kvm/vmx/vmx.c +1 -2
@@ -4007,8 +4007,7 @@ static int vmx_deliver_posted_interrupt(if (pi_test_and_set_on (&vmx->pi_desc))return 0 ; -if (vcpu !=kvm_get_running_vcpu () && - !kvm_vcpu_trigger_posted_interrupt (vcpu, false)) +if (!kvm_vcpu_trigger_posted_interrupt (vcpu, false))kvm_vcpu_kick (vcpu);return 0 ;
Greg Kroah-Hartman
maintainerPATCH 50/76 pinctrl: stm32: consider the GPIO offset to expose all the GPIO lines
In reply to Greg Kroah-HartmanFrom: Fabien Dessenne <[email protected]>
commit b67210cc217f9ca1c576909454d846970c13dfd4 upstream.
Consider the GPIO controller offset (from "gpio-ranges") to compute the maximum GPIO line number.
This fixes an issue where gpio-ranges uses a non-null offset.
e.g.: gpio-ranges = <&pinctrl 6 86 10>
In that case the last valid GPIO line is not 9 but 15 (6 + 10 - 1)
--- drivers/pinctrl/stm32/pinctrl-stm32.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/pinctrl/stm32/pinctrl-stm32.c +4 -4
@@ -1255,10 +1255,10 @@ static int stm32_gpiolib_register_bank(s bank_nr = args.args[1 ] /STM32_GPIO_PINS_PER_BANK ; bank->gpio_chip.base = args.args[1 ]; - npins = args.args[2 ]; -while (!of_parse_phandle_with_fixed_args (np,"gpio-ranges" ,3 , - ++i, &args)) - npins += args.args[2 ]; +/* get the last defined gpio line (offset + nb of pins) */ + npins = args.args[0 ] + args.args[2 ]; +while (!of_parse_phandle_with_fixed_args (np,"gpio-ranges" ,3 , ++i, &args)) + npins =max (npins, (int )(args.args[0 ] + args.args[2 ])); }else { bank_nr = pctl->nbanks; bank->gpio_chip.base = bank_nr *STM32_GPIO_PINS_PER_BANK ;
Greg Kroah-Hartman
maintainerPATCH 51/76 gpio: dln2: Fix interrupts when replugging the device
In reply to Greg Kroah-HartmanFrom: Noralf Trønnes <[email protected]>
commit 9a5875f14b0e3a13ae314883f1bb72b7f31fac07 upstream.
When replugging the device the following message shows up:
gpio gpiochip2: (dln2): detected irqchip that is shared with multiple gpiochips: please fix the driver.
This also has the effect that interrupts won't work.
The same problem would also show up if multiple devices where plugged in.
Fix this by allocating the irq_chip data structure per instance like other drivers do.
I don't know when this problem appeared, but it is present in 5.10.
--- drivers/gpio/gpio-dln2.c | 19 +++++++++---------- 1 file changed, 9 insertions(+), 10 deletions(-)
drivers/gpio/gpio-dln2.c +9 -10
@@ -46,6 +46,7 @@struct dln2_gpio {struct platform_device *pdev;struct gpio_chip gpio; +struct irq_chip irqchip;/* * Cache pin direction to save us one transfer, since the hardware has
@@ -383,15 +384,6 @@ static void dln2_irq_bus_unlock(struct imutex_unlock (&dln2->irq_lock); } -static struct irq_chip dln2_gpio_irqchip = { - .name ="dln2-irq" , - .irq_mask = dln2_irq_mask, - .irq_unmask = dln2_irq_unmask, - .irq_set_type = dln2_irq_set_type, - .irq_bus_lock = dln2_irq_bus_lock, - .irq_bus_sync_unlock = dln2_irq_bus_unlock, -}; -static void dln2_gpio_event (struct platform_device *pdev,u16 echo,const void *data,int len) {
@@ -477,8 +469,15 @@ static int dln2_gpio_probe(struct platfo dln2->gpio.direction_output = dln2_gpio_direction_output; dln2->gpio.set_config = dln2_gpio_set_config; + dln2->irqchip.name ="dln2-irq" , + dln2->irqchip.irq_mask = dln2_irq_mask, + dln2->irqchip.irq_unmask = dln2_irq_unmask, + dln2->irqchip.irq_set_type = dln2_irq_set_type, + dln2->irqchip.irq_bus_lock = dln2_irq_bus_lock, + dln2->irqchip.irq_bus_sync_unlock = dln2_irq_bus_unlock, + girq = &dln2->gpio.irq; - girq->chip = &dln2_gpio_irqchip; + girq->chip = &dln2->irqchip;/* The event comes from the outside so no parent handler */ girq->parent_handler =NULL ; girq->num_parents =0 ;
Greg Kroah-Hartman
maintainerPATCH 52/76 mmc: sdhci-tegra: Fix switch to HS400ES mode
In reply to Greg Kroah-HartmanFrom: Prathamesh Shete <[email protected]>
commit 4fc7261dbab139d3c64c3b618262504e16cfe7ee upstream.
When CMD13 is sent after switching to HS400ES mode, the bus is operating at either MMC_HIGH_26_MAX_DTR or MMC_HIGH_52_MAX_DTR. To meet Tegra SDHCI requirement at HS400ES mode, force SDHCI interface clock to MMC_HS200_MAX_DTR (200 MHz) so that host controller CAR clock and the interface clock are rate matched.
--- drivers/mmc/host/sdhci-tegra.c | 43 ++++++++++++++++++++++++----------------- 1 file changed, 26 insertions(+), 17 deletions(-)
drivers/mmc/host/sdhci-tegra.c +26 -17
@@ -354,23 +354,6 @@ static void tegra_sdhci_set_tap(struct s } } -static void tegra_sdhci_hs400_enhanced_strobe (struct mmc_host *mmc, -struct mmc_ios *ios) -{ -struct sdhci_host *host =mmc_priv (mmc); -u32 val; - - val =sdhci_readl (host,SDHCI_TEGRA_VENDOR_SYS_SW_CTRL ); - -if (ios->enhanced_strobe) - val |=SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE ; -else - val &= ~SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE ; - -sdhci_writel (host, val,SDHCI_TEGRA_VENDOR_SYS_SW_CTRL ); - -} -static void tegra_sdhci_reset (struct sdhci_host *host,u8 mask) {struct sdhci_pltfm_host *pltfm_host =sdhci_priv (host);
@@ -791,6 +774,32 @@ static void tegra_sdhci_set_clock(struct } } +static void tegra_sdhci_hs400_enhanced_strobe (struct mmc_host *mmc, +struct mmc_ios *ios) +{ +struct sdhci_host *host =mmc_priv (mmc); +u32 val; + + val =sdhci_readl (host,SDHCI_TEGRA_VENDOR_SYS_SW_CTRL ); + +if (ios->enhanced_strobe) { + val |=SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE ; +/* +* When CMD13 is sent from mmc_select_hs400es() after +* switching to HS400ES mode, the bus is operating at +* either MMC_HIGH_26_MAX_DTR or MMC_HIGH_52_MAX_DTR. +* To meet Tegra SDHCI requirement at HS400ES mode, force SDHCI +* interface clock to MMC_HS200_MAX_DTR (200 MHz) so that host +* controller CAR clock and the interface clock are rate matched. +*/ +tegra_sdhci_set_clock (host,MMC_HS200_MAX_DTR ); + }else { + val &= ~SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE ; + } + +sdhci_writel (host, val,SDHCI_TEGRA_VENDOR_SYS_SW_CTRL ); +} +static unsigned int tegra_sdhci_get_max_clock (struct sdhci_host *host) {struct sdhci_pltfm_host *pltfm_host =sdhci_priv (host);
Greg Kroah-Hartman
maintainerPATCH 53/76 mmc: meson-mx-sdhc: Set MANUAL_STOP for multi-block SDIO commands
In reply to Greg Kroah-HartmanFrom: Martin Blumenstingl <[email protected]>
commit f89b548ca66be7500dcd92ee8e61590f7d08ac91 upstream.
The vendor driver implements special handling for multi-block SD_IO_RW_EXTENDED (and SD_IO_RW_DIRECT) commands which have data attached to them. It sets the MANUAL_STOP bit in the MESON_SDHC_MISC register for these commands. In all other cases this bit is cleared. Here we omit SD_IO_RW_DIRECT since that command never has any data attached to it.
This fixes SDIO wifi using the brcmfmac driver which reported the following error without this change on a Netxeon S82 board using a Meson8 (S802) SoC:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_sdiod_ramrw: membytes transfer failed
brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
at 0x00000000 brcmf_sdio_download_firmware: dongle image file download failed
And with this change:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
have limited channels available
brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
version 5.90.195.89.6 FWID 01-b30a427d--- drivers/mmc/host/meson-mx-sdhc-mmc.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)
drivers/mmc/host/meson-mx-sdhc-mmc.c +16 -0
@@ -135,6 +135,7 @@ static void meson_mx_sdhc_start_cmd(stru struct mmc_command *cmd) {struct meson_mx_sdhc_host *host =mmc_priv (mmc); +bool manual_stop = false;u32 ictl, send;int pack_len;
@@ -172,12 +173,27 @@ static void meson_mx_sdhc_start_cmd(struelse /* software flush: */ ictl |=MESON_SDHC_ICTL_DATA_XFER_OK ; + +/* +* Mimic the logic from the vendor driver where (only) +* SD_IO_RW_EXTENDED commands with more than one block set the +* MESON_SDHC_MISC_MANUAL_STOP bit. This fixes the firmware +* download in the brcmfmac driver for a BCM43362/1 card. +* Without this sdio_memcpy_toio() (with a size of 219557 +* bytes) times out if MESON_SDHC_MISC_MANUAL_STOP is not set. +*/ + manual_stop = cmd->data->blocks >1 && + cmd->opcode ==SD_IO_RW_EXTENDED ; }else { pack_len =0 ; ictl |=MESON_SDHC_ICTL_RESP_OK ; } +regmap_update_bits (host->regmap,MESON_SDHC_MISC , +MESON_SDHC_MISC_MANUAL_STOP , + manual_stop ?MESON_SDHC_MISC_MANUAL_STOP :0 ); +if (cmd->opcode ==MMC_STOP_TRANSMISSION ) send |=MESON_SDHC_SEND_DATA_STOP ;
Greg Kroah-Hartman
maintainerPATCH 54/76 mmc: core: Disable card detect during shutdown
In reply to Greg Kroah-HartmanFrom: Ulf Hansson <[email protected]>
commit 66c915d09b942fb3b2b0cb2f56562180901fba17 upstream.
It's seems prone to problems by allowing card detect and its corresponding mmc_rescan() work to run, during platform shutdown. For example, we may end up turning off the power while initializing a card, which potentially could damage it.
To avoid this scenario, let's add ->shutdown_pre() callback for the mmc host class device and then turn of the card detect from there.
--- drivers/mmc/core/core.c | 7 ++++++- drivers/mmc/core/core.h | 1 + drivers/mmc/core/host.c | 9 +++++++++ 3 files changed, 16 insertions(+), 1 deletion(-)
drivers/mmc/core/core.c +6 -1
@@ -2327,7 +2327,7 @@ void mmc_start_host(struct mmc_host *hos_mmc_detect_change (host,0 , false); } -void mmc_stop_host (struct mmc_host *host) +void __mmc_stop_host (struct mmc_host *host) {if (host->slot.cd_irq >=0 ) {mmc_gpio_set_cd_wake (host, false);
@@ -2336,6 +2336,11 @@ void mmc_stop_host(struct mmc_host *host host->rescan_disable =1 ;cancel_delayed_work_sync (&host->detect); +} + +void mmc_stop_host (struct mmc_host *host) +{ +__mmc_stop_host (host);/* clear pm flags now and let card drivers set them as needed */ host->pm_flags =0 ;
drivers/mmc/core/core.h +1 -0
@@ -69,6 +69,7 @@ static inline void mmc_delay(unsigned invoid mmc_rescan (struct work_struct *work);void mmc_start_host (struct mmc_host *host); +void __mmc_stop_host (struct mmc_host *host);void mmc_stop_host (struct mmc_host *host); void _mmc_detect_change(struct mmc_host *host, unsigned long delay,
drivers/mmc/core/host.c +9 -0
@@ -79,9 +79,18 @@ static void mmc_host_classdev_release(stkfree (host); } +static int mmc_host_classdev_shutdown (struct device *dev) +{ +struct mmc_host *host =cls_dev_to_mmc_host (dev); + +__mmc_stop_host (host); +return 0 ; +} +static struct class mmc_host_class = { .name ="mmc_host" , .dev_release = mmc_host_classdev_release, + .shutdown_pre = mmc_host_classdev_shutdown, .pm =MMC_HOST_CLASS_DEV_PM_OPS , };
Greg Kroah-Hartman
maintainerPATCH 55/76 mmc: mmci: stm32: clear DLYB_CR after sending tuning command
In reply to Greg Kroah-HartmanFrom: Yann Gautier <[email protected]>
commit ff31ee0a0f471776f67be5e5275c18d17736fc6b upstream.
During test campaign, and especially after several unbind/bind sequences, it has been seen that the SD-card on SDMMC1 thread could freeze. The freeze always appear on a CMD23 following a CMD19. Checking SDMMC internal registers shows that the tuning command (CMD19) has failed.
The freeze is then due to the delay block involved in the tuning sequence. To correct this, clear the delay block register DLYB_CR register after the tuning commands.
--- drivers/mmc/host/mmci_stm32_sdmmc.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/mmc/host/mmci_stm32_sdmmc.c +2 -0
@@ -441,6 +441,8 @@ static int sdmmc_dlyb_phase_tuning(strucreturn -EINVAL ; } +writel_relaxed (0 , dlyb->base +DLYB_CR ); + phase = end_of_len - max_len /2 ;sdmmc_dlyb_set_cfgr (dlyb, dlyb->unit, phase, false);
Greg Kroah-Hartman
maintainerPATCH 56/76 ARM: 9169/1: entry: fix Thumb2 bug in iWMMXt exception handling
In reply to Greg Kroah-HartmanFrom: Ard Biesheuvel <[email protected]>
commit 8536a5ef886005bc443c2da9b842d69fd3d7647f upstream.
The Thumb2 version of the FP exception handling entry code treats the register holding the CP number (R8) differently, resulting in the iWMMXT CP number check to be incorrect.
Fix this by unifying the ARM and Thumb2 code paths, and switch the order of the additions of the TI_USED_CP offset and the shifted CP index.
--- arch/arm/kernel/entry-armv.S | 8 +++----- 1 file changed, 3 insertions(+), 5 deletions(-)
arch/arm/kernel/entry-armv.S +3 -5
@@ -596,11 +596,9 @@ call_fpe: tstne r0, #0x04000000 @ bit 26 set on both ARM and Thumb-2 reteq lr and r8, r0, #0x00000f00 @ mask out CP number - THUMB( lsr r8, r8, #8 ) mov r7, #1 - add r6, r10, #TI_USED_CP - ARM( strb r7, [r6, r8, lsr #8] ) @ set appropriate used_cp[] - THUMB( strb r7, [r6, r8] ) @ set appropriate used_cp[] + add r6, r10, r8, lsr #8 @ add used_cp[] array offset first + strb r7, [r6, #TI_USED_CP] @ set appropriate used_cp[] #ifdef CONFIG_IWMMXT @ Test if we need to give access to iWMMXt coprocessors ldr r5, [r10, #TI_FLAGS]
@@ -609,7 +607,7 @@ call_fpe: bcs iwmmxt_task_enable #endif ARM( add pc, pc, r8, lsr #6 ) - THUMB( lsl r8, r8, #2 ) + THUMB( lsr r8, r8, #6 ) THUMB( add pc, r8 ) nop
Greg Kroah-Hartman
maintainerPATCH 57/76 mac80211: fix locking in ieee80211_start_ap error path
In reply to Greg Kroah-HartmanFrom: Johannes Berg <[email protected]>
commit 87a270625a89fc841f1a7e21aae6176543d8385c upstream.
We need to hold the local->mtx to release the channel context, as even encoded by the lockdep_assert_held() there. Fix it.
--- net/mac80211/cfg.c | 3 +++ 1 file changed, 3 insertions(+)
net/mac80211/cfg.c +3 -0
@@ -1217,7 +1217,10 @@ static int ieee80211_start_ap(struct wipreturn 0 ; error: +mutex_lock (&local->mtx);ieee80211_vif_release_channel (sdata); +mutex_unlock (&local->mtx); +return err; }
Greg Kroah-Hartman
maintainerPATCH 58/76 mm/hwpoison: clear MF_COUNT_INCREASED before retrying get_any_page()
In reply to Greg Kroah-HartmanFrom: Liu Shixin <[email protected]>
commit 2a57d83c78f889bf3f54eede908d0643c40d5418 upstream.
Hulk Robot reported a panic in put_page_testzero() when testing madvise() with MADV_SOFT_OFFLINE. The BUG() is triggered when retrying get_any_page(). This is because we keep MF_COUNT_INCREASED flag in second try but the refcnt is not increased.
page dumped because: VM_BUG_ON_PAGE(page_ref_count(page) == 0)
------------[ cut here ]------------
kernel BUG at include/linux/mm.h:737!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 5 PID: 2135 Comm: sshd Tainted: G B 5.16.0-rc6-dirty #373
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: release_pages+0x53f/0x840
Call Trace:
free_pages_and_swap_cache+0x64/0x80
tlb_flush_mmu+0x6f/0x220
unmap_page_range+0xe6c/0x12c0
unmap_single_vma+0x90/0x170
unmap_vmas+0xc4/0x180
exit_mmap+0xde/0x3a0
mmput+0xa3/0x250
do_exit+0x564/0x1470
do_group_exit+0x3b/0x100
__do_sys_exit_group+0x13/0x20
__x64_sys_exit_group+0x16/0x20
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Modules linked in:
---[ end trace e99579b570fe0649 ]---
RIP: 0010:release_pages+0x53f/0x840--- mm/memory-failure.c | 1 + 1 file changed, 1 insertion(+)
mm/memory-failure.c +1 -0
@@ -1938,6 +1938,7 @@ retry:else if (ret ==0 )if (soft_offline_free_page (page) && try_again) { try_again = false; + flags &= ~MF_COUNT_INCREASED ; goto retry; }
Greg Kroah-Hartman
maintainerPATCH 59/76 tee: optee: Fix incorrect page free bug
In reply to Greg Kroah-HartmanFrom: Sumit Garg <[email protected]>
commit 18549bf4b21c739a9def39f27dcac53e27286ab5 upstream.
Pointer to the allocated pages (struct page *page) has already progressed towards the end of allocation. It is incorrect to perform __free_pages(page, order) using this pointer as we would free any arbitrary pages. Fix this by stop modifying the page pointer.
--- drivers/tee/optee/shm_pool.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/tee/optee/shm_pool.c +2 -4
@@ -41,10 +41,8 @@ static int pool_op_alloc(struct tee_shm_ goto err; } -for (i =0 ; i < nr_pages; i++) { - pages[i] = page; - page++; - } +for (i =0 ; i < nr_pages; i++) + pages[i] = page + i; shm->flags |=TEE_SHM_REGISTER ; rc = optee_shm_register(shm->ctx, shm, pages, nr_pages,
Greg Kroah-Hartman
maintainerPATCH 60/76 f2fs: fix to do sanity check on last xattr entry in __f2fs_setxattr()
In reply to Greg Kroah-HartmanFrom: Chao Yu <[email protected]>
commit 5598b24efaf4892741c798b425d543e4bed357a1 upstream.
As Wenqing Liu reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215235
- Overview
page fault in f2fs_setxattr() when mount and operate on corrupted image
- Reproduce
tested on kernel 5.16-rc3, 5.15.X under root
1. unzip tmp7.zip
2. ./single.sh f2fs 7
Sometimes need to run the script several times
- Kernel dump
loop0: detected capacity change from 0 to 131072 F2FS-fs (loop0): Found nat_bits in checkpoint F2FS-fs (loop0): Mounted with checkpoint version = 7548c2ee
BUG: unable to handle page fault for address: ffffe47bc7123f48 RIP: 0010:kfree+0x66/0x320 Call Trace: __f2fs_setxattr+0x2aa/0xc00 [f2fs] f2fs_setxattr+0xfa/0x480 [f2fs] __f2fs_set_acl+0x19b/0x330 [f2fs] __vfs_removexattr+0x52/0x70 __vfs_removexattr_locked+0xb1/0x140 vfs_removexattr+0x56/0x100 removexattr+0x57/0x80 path_removexattr+0xa3/0xc0 __x64_sys_removexattr+0x17/0x20 do_syscall_64+0x37/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae
The root cause is in __f2fs_setxattr(), we missed to do sanity check on last xattr entry, result in out-of-bound memory access during updating inconsistent xattr data of target inode.
After the fix, it can detect such xattr inconsistency as below:
F2FS-fs (loop11): inode (7) has invalid last xattr entry, entry_size: 60676 F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has invalid last xattr entry, entry_size: 47736
--- fs/f2fs/xattr.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)
fs/f2fs/xattr.c +10 -1
@@ -680,8 +680,17 @@ static int __f2fs_setxattr(struct inode } last = here; -while (!IS_XATTR_LAST_ENTRY (last)) +while (!IS_XATTR_LAST_ENTRY (last)) { +if ((void *)(last) +sizeof (__u32) > last_base_addr || + (void *)XATTR_NEXT_ENTRY (last) > last_base_addr) { +f2fs_err (F2FS_I_SB (inode),"inode (%lu) has invalid last xattr entry, entry_size: %zu" , + inode->i_ino,ENTRY_SIZE (last)); +set_sbi_flag (F2FS_I_SB (inode),SBI_NEED_FSCK ); + error = -EFSCORRUPTED ; + goto exit; + } last =XATTR_NEXT_ENTRY (last); + } newsize =XATTR_ALIGN (sizeof (struct f2fs_xattr_entry ) + len + size);
Re: [PATCH 5.10 60/76] f2fs: fix to do sanity check on last xattr entry in __f2fs_setxattr()
Hi,
Quoted 68 lines · Greg Kroah-Hartman
From: Chao Yu <[email protected]>
commit
5598b24efaf4892741c798b425d543e4bed357a1upstream.As Wenqing Liu reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215235
- Overview
page fault inf2fs_setxattr()when mount and operate on corrupted image- Reproduce
tested on kernel 5.16-rc3, 5.15.X under root1. unzip tmp7.zip
2. ./single.sh f2fs 7Sometimes need to run the script several times
- Kernel dump
loop0: detected capacity change from 0 to 131072 F2FS-fs (loop0): Foundnat_bitsin checkpoint F2FS-fs (loop0): Mounted with checkpoint version =7548c2eeBUG: unable to handle page fault for address: ffffe47bc7123f48 RIP: 0010:kfree+0x66/0x320 Call Trace: __f2fs_setxattr+0x2aa/0xc00 [f2fs] f2fs_setxattr+0xfa/0x480 [f2fs] __f2fs_set_acl+0x19b/0x330 [f2fs] __vfs_removexattr+0x52/0x70 __vfs_removexattr_locked+0xb1/0x140 vfs_removexattr+0x56/0x100 removexattr+0x57/0x80 path_removexattr+0xa3/0xc0 __x64_sys_removexattr+0x17/0x20 do_syscall_64+0x37/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xaeThe root cause is in
__f2fs_setxattr(), we missed to do sanity check on last xattr entry, result in out-of-bound memory access during updating inconsistent xattr data of target inode.After the fix, it can detect such xattr inconsistency as below:
F2FS-fs (loop11): inode (7) has invalid last xattr entry,
entry_size: 60676 F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has invalid last xattr entry,entry_size: 47736Reported-by Wenqing Liu <[email protected]>Signed-off-by Chao Yu <[email protected]>Signed-off-by Jaegeuk Kim <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>--- fs/f2fs/xattr.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)fs/f2fs/xattr.c +3
-1@@ -680,8 +680,17 @@ static int __f2fs_setxattr(struct inode } last = here; -while (!IS_XATTR_LAST_ENTRY (last)) +while (!IS_XATTR_LAST_ENTRY (last)) { +if ((void *)(last) +sizeof (__u32) > last_base_addr || + (void *)XATTR_NEXT_ENTRY (last) > last_base_addr) {
fs/f2fs/xattr.c static int __f2fs_setxattr(struct inode · line 695
Quoted 10 lines
fs/f2fs/xattr.c +7
-0+f2fs_err (F2FS_I_SB (inode),"inode (%lu) has invalid last xattr entry, entry_size: %zu" , + inode->i_ino,ENTRY_SIZE (last)); +set_sbi_flag (F2FS_I_SB (inode),SBI_NEED_FSCK ); + error = -EFSCORRUPTED ; + goto exit; + } last =XATTR_NEXT_ENTRY (last); + } newsize =XATTR_ALIGN (sizeof (struct f2fs_xattr_entry ) + len + size);
It looks this commit while it was applied to several stable series (TTBOMK in 5.15.12, 5.10.89, 5.4.169, 4.19.223 and 4.14.260) it is still missing from mainline, Chao, or anyone else, do you know what happened here?
Regards,
Salvatore
Re: [PATCH 5.10 60/76] f2fs: fix to do sanity check on last xattr entry in __f2fs_setxattr()
Quoted 6 lines · Salvatore Bonaccorso
Hi,
Quoted 3 lines · Greg Kroah-Hartman
From: Chao Yu <[email protected]>
commit
5598b24efaf4892741c798b425d543e4bed357a1upstream.
I've no idea.
I didn't add this line from v1 to v3:
https://lore.kernel.org/lkml/[email protected]/T/
https://lore.kernel.org/all/[email protected]/T/
https://lore.kernel.org/all/[email protected]/T/
Am I missing anything?
Thanks,
Quoted 83 lines
Quoted 65 lines
As Wenqing Liu reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215235
- Overview
page fault inf2fs_setxattr()when mount and operate on corrupted image- Reproduce
tested on kernel 5.16-rc3, 5.15.X under root1. unzip tmp7.zip
2. ./single.sh f2fs 7Sometimes need to run the script several times
- Kernel dump
loop0: detected capacity change from 0 to 131072 F2FS-fs (loop0): Foundnat_bitsin checkpoint F2FS-fs (loop0): Mounted with checkpoint version =7548c2eeBUG: unable to handle page fault for address: ffffe47bc7123f48 RIP: 0010:kfree+0x66/0x320 Call Trace: __f2fs_setxattr+0x2aa/0xc00 [f2fs] f2fs_setxattr+0xfa/0x480 [f2fs] __f2fs_set_acl+0x19b/0x330 [f2fs] __vfs_removexattr+0x52/0x70 __vfs_removexattr_locked+0xb1/0x140 vfs_removexattr+0x56/0x100 removexattr+0x57/0x80 path_removexattr+0xa3/0xc0 __x64_sys_removexattr+0x17/0x20 do_syscall_64+0x37/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xaeThe root cause is in
__f2fs_setxattr(), we missed to do sanity check on last xattr entry, result in out-of-bound memory access during updating inconsistent xattr data of target inode.After the fix, it can detect such xattr inconsistency as below:
F2FS-fs (loop11): inode (7) has invalid last xattr entry,
entry_size: 60676 F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has invalid last xattr entry,entry_size: 47736Reported-by Wenqing Liu <[email protected]>Signed-off-by Chao Yu <[email protected]>Signed-off-by Jaegeuk Kim <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>--- fs/f2fs/xattr.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)fs/f2fs/xattr.c +3
-1@@ -680,8 +680,17 @@ static int __f2fs_setxattr(struct inode } last = here; -while (!IS_XATTR_LAST_ENTRY (last)) +while (!IS_XATTR_LAST_ENTRY (last)) { +if ((void *)(last) +sizeof (__u32) > last_base_addr || + (void *)XATTR_NEXT_ENTRY (last) > last_base_addr) {fs/f2fs/xattr.c static int __f2fs_setxattr(struct inode · line 695
Quoted 10 lines
fs/f2fs/xattr.c +7
-0+f2fs_err (F2FS_I_SB (inode),"inode (%lu) has invalid last xattr entry, entry_size: %zu" , + inode->i_ino,ENTRY_SIZE (last)); +set_sbi_flag (F2FS_I_SB (inode),SBI_NEED_FSCK ); + error = -EFSCORRUPTED ; + goto exit; + } last =XATTR_NEXT_ENTRY (last); + } newsize =XATTR_ALIGN (sizeof (struct f2fs_xattr_entry ) + len + size);It looks this commit while it was applied to several stable series (TTBOMK in 5.15.12, 5.10.89, 5.4.169, 4.19.223 and 4.14.260) it is still missing from mainline, Chao, or anyone else, do you know what happened here?
Regards,
Salvatore
Re: [PATCH 5.10 60/76] f2fs: fix to do sanity check on last xattr entry in __f2fs_setxattr()
Hi,
Quoted 10 lines · Chao Yu
Quoted 6 lines · Salvatore Bonaccorso
Hi,
Quoted 3 lines · Greg Kroah-Hartman
From: Chao Yu <[email protected]>
commit
5598b24efaf4892741c798b425d543e4bed357a1upstream.I've no idea.
Quoted 7 lines
I didn't add this line from v1 to v3:
https://lore.kernel.org/lkml/[email protected]/T/
https://lore.kernel.org/all/[email protected]/T/
https://lore.kernel.org/all/[email protected]/T/Am I missing anything?
The line is added when a commit from "upstream" is added to the stable series to identify the upstream commit it is taken from for cherry-pick (or backport).
Strange so, that the fix is not in mainline actually yet.
Regards,
Salvatore
Greg Kroah-Hartman
maintainerRe: [PATCH 5.10 60/76] f2fs: fix to do sanity check on last xattr entry in __f2fs_setxattr()
Quoted 19 lines · Salvatore Bonaccorso
Hi,
Quoted 16 lines · Chao Yu
Quoted 6 lines · Salvatore Bonaccorso
Hi,
Quoted 3 lines · Greg Kroah-Hartman
From: Chao Yu <[email protected]>
commit
5598b24efaf4892741c798b425d543e4bed357a1upstream.I've no idea.
I didn't add this line from v1 to v3:
https://lore.kernel.org/lkml/[email protected]/T/
https://lore.kernel.org/all/[email protected]/T/
https://lore.kernel.org/all/[email protected]/T/
Quoted 7 lines
Quoted 1 line
Am I missing anything?
The line is added when a commit from "upstream" is added to the stable series to identify the upstream commit it is taken from for cherry-pick (or backport).
Strange so, that the fix is not in mainline actually yet.
I thought it was about to be sent to Linus. Why has the f2fs maintainer not sent a merge request to him to get this merged properly yet?
thanks,
greg k-h
Re: [PATCH 5.10 60/76] f2fs: fix to do sanity check on last xattr entry in __f2fs_setxattr()
Quoted 22 lines · Greg Kroah-Hartman
Quoted 21 lines · Salvatore Bonaccorso
Hi,
Quoted 17 lines · Chao Yu
Quoted 6 lines · Salvatore Bonaccorso
Hi,
Quoted 3 lines · Greg Kroah-Hartman
From: Chao Yu <[email protected]>
commit
5598b24efaf4892741c798b425d543e4bed357a1upstream.I've no idea.
I didn't add this line from v1 to v3:
https://lore.kernel.org/lkml/[email protected]/T/
https://lore.kernel.org/all/[email protected]/T/
https://lore.kernel.org/all/[email protected]/T/Am I missing anything?
Quoted 8 lines
Quoted 5 lines
The line is added when a commit from "upstream" is added to the stable series to identify the upstream commit it is taken from for cherry-pick (or backport).
Strange so, that the fix is not in mainline actually yet.
I thought it was about to be sent to Linus. Why has the f2fs maintainer not sent a merge request to him to get this merged properly yet?
It's very surprising that -stable can cherry-pick non-upstreamed patches based on the stable maintainer's self assumption. Please wait for being upstreamed.
The patch is on track via -next.
https://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs.git/commit/?h=dev&id=5598b24efaf4892741c798b425d543e4bed357a1
Quoted 4 lines
thanks,
greg k-h
Greg Kroah-Hartman
maintainerRe: [PATCH 5.10 60/76] f2fs: fix to do sanity check on last xattr entry in __f2fs_setxattr()
Quoted 27 lines · Jaegeuk Kim
Quoted 26 lines · Greg Kroah-Hartman
Quoted 25 lines · Salvatore Bonaccorso
Hi,
Quoted 10 lines · Chao Yu
Quoted 6 lines · Salvatore Bonaccorso
Hi,
Quoted 3 lines · Greg Kroah-Hartman
From: Chao Yu <[email protected]>
commit
5598b24efaf4892741c798b425d543e4bed357a1upstream.I've no idea.
Quoted 7 lines
I didn't add this line from v1 to v3:
https://lore.kernel.org/lkml/[email protected]/T/
https://lore.kernel.org/all/[email protected]/T/
https://lore.kernel.org/all/[email protected]/T/Am I missing anything?
The line is added when a commit from "upstream" is added to the stable series to identify the upstream commit it is taken from for cherry-pick (or backport).
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Strange so, that the fix is not in mainline actually yet.
I thought it was about to be sent to Linus. Why has the f2fs maintainer not sent a merge request to him to get this merged properly yet?
It's very surprising that -stable can cherry-pick non-upstreamed patches based on the stable maintainer's self assumption. Please wait for being upstreamed.
I normally do wait, but when a commit has a public CVE registered for it, and it shows up in -next, I assume that it will be sent to Linus any moment now. Because of that, I made the call to take the patch then.
Odd that you wish to delay this, sorry I took it early.
greg k-h
Greg Kroah-Hartman
maintainerPATCH 61/76 ceph: fix up non-directory creation in SGID directories
In reply to Greg Kroah-HartmanFrom: Christian Brauner <[email protected]>
commit fd84bfdddd169c219c3a637889a8b87f70a072c2 upstream.
Ceph always inherits the SGID bit if it is set on the parent inode, while the generic inode_init_owner does not do this in a few cases where it can create a possible security problem (cf. [1]).
Update ceph to strip the SGID bit just as inode_init_owner would.
This bug was detected by the mapped mount testsuite in [3]. The testsuite tests all core VFS functionality and semantics with and without mapped mounts. That is to say it functions as a generic VFS testsuite in addition to a mapped mount testsuite. While working on mapped mount support for ceph, SIGD inheritance was the only failing test for ceph after the port.
The same bug was detected by the mapped mount testsuite in XFS in January 2021 (cf. [2]).
[1]: commit 0fa3ecd87848 ("Fix up non-directory creation in SGID directories") [2]: commit 01ea173e103e ("xfs: fix up non-directory creation in SGID directories") [3]: https://git.kernel.org/fs/xfs/xfstests-dev.git
--- fs/ceph/file.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-)
fs/ceph/file.c +15 -3
@@ -603,13 +603,25 @@ static int ceph_finish_async_create(stru in.cap.realm =cpu_to_le64 (ci->i_snap_realm->ino); in.cap.flags =CEPH_CAP_FLAG_AUTH ; in.ctime = in.mtime = in.atime = iinfo.btime; - in.mode =cpu_to_le32 ((u32 )mode); in.truncate_seq =cpu_to_le32 (1 ); in.truncate_size =cpu_to_le64 (-1ULL ); in.xattr_version =cpu_to_le64 (1 ); in.uid =cpu_to_le32 (from_kuid (&init_user_ns,current_fsuid ())); - in.gid =cpu_to_le32 (from_kgid (&init_user_ns, dir->i_mode &S_ISGID ? - dir->i_gid :current_fsgid ())); +if (dir->i_mode &S_ISGID ) { + in.gid =cpu_to_le32 (from_kgid (&init_user_ns, dir->i_gid)); + +/* Directories always inherit the setgid bit. */ +if (S_ISDIR (mode)) + mode |=S_ISGID ; +else if ((mode & (S_ISGID |S_IXGRP )) == (S_ISGID |S_IXGRP ) && + !in_group_p (dir->i_gid) && + !capable_wrt_inode_uidgid (dir,CAP_FSETID )) + mode &= ~S_ISGID ; + }else { + in.gid =cpu_to_le32 (from_kgid (&init_user_ns,current_fsgid ())); + } + in.mode =cpu_to_le32 ((u32 )mode); + in.nlink =cpu_to_le32 (1 ); in.max_size =cpu_to_le64 (lo->stripe_unit);
Greg Kroah-Hartman
maintainerPATCH 62/76 usb: gadget: u_ether: fix race in setting MAC address in setup phase
In reply to Greg Kroah-HartmanFrom: Marian Postevca <[email protected]>
commit 890d5b40908bfd1a79be018d2d297cf9df60f4ee upstream.
When listening for notifications through netlink of a new interface being registered, sporadically, it is possible for the MAC to be read as zero. The zero MAC address lasts a short period of time and then switches to a valid random MAC address.
This causes problems for netd in Android, which assumes that the interface is malfunctioning and will not use it.
In the good case we get this log:InterfaceController::getCfg() ifName usb0
hwAddr 92:a8:f0:73:79:5b ipv4Addr 0.0.0.0 flags 0x1002
In the error case we get these logs:InterfaceController::getCfg() ifName usb0
hwAddr 00:00:00:00:00:00 ipv4Addr 0.0.0.0 flags 0x1002
netd : interfaceGetCfg("usb0")
netd : interfaceSetCfg() -> ServiceSpecificException
(99, "[Cannot assign requested address] : ioctl() failed")
The reason for the issue is the order in which the interface is setup, it is first registered through register_netdev() and after the MAC address is set.
Fixed by first setting the MAC address of the net_device and after that calling register_netdev().
--- drivers/usb/gadget/function/u_ether.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)
drivers/usb/gadget/function/u_ether.c +5 -10
@@ -860,19 +860,23 @@ int gether_register_netdev(struct net_de {struct eth_dev *dev;struct usb_gadget *g; -struct sockaddr sa;int status;if (!net->dev.parent)return -EINVAL ; dev =netdev_priv (net); g = dev->gadget; + +memcpy (net->dev_addr, dev->dev_mac,ETH_ALEN ); + net->addr_assign_type =NET_ADDR_RANDOM ; + status =register_netdev (net);if (status <0 ) {dev_dbg (&g->dev,"register_netdev failed, %d\n" , status);return status; }else {INFO (dev,"HOST MAC %pM\n" , dev->host_mac); +INFO (dev,"MAC %pM\n" , dev->dev_mac);/* two kinds of host-initiated state changes: * - iff DATA transfer is active, carrier is "on"
@@ -880,15 +884,6 @@ int gether_register_netdev(struct net_de*/ netif_carrier_off (net); } - sa.sa_family = net->type; -memcpy (sa.sa_data, dev->dev_mac,ETH_ALEN ); -rtnl_lock (); - status =dev_set_mac_address (net, &sa,NULL ); -rtnl_unlock (); -if (status) -pr_warn ("cannot set self ethernet address: %d\n" , status); -else -INFO (dev,"MAC %pM\n" , dev->dev_mac);return status; }
Greg Kroah-Hartman
maintainerPATCH 63/76 KVM: VMX: Fix stale docs for kvm-intel.emulate_invalid_guest_state
In reply to Greg Kroah-HartmanFrom: Sean Christopherson <[email protected]>
commit 0ff29701ffad9a5d5a24344d8b09f3af7b96ffda upstream.
Update the documentation for kvm-intel's emulate_invalid_guest_state to rectify the description of KVM's default behavior, and to document that the behavior and thus parameter only applies to L1.
Message-Id: <[email protected]>
--- Documentation/admin-guide/kernel-parameters.txt | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
Documentation/admin-guide/kernel-parameters.txt +6 -2
@@ -2294,8 +2294,12 @@ Default is 1 (enabled) kvm-intel.emulate_invalid_guest_state= - [KVM,Intel] Enable emulation of invalid guest states - Default is 0 (disabled) + [KVM,Intel] Disable emulation of invalid guest state. + Ignored if kvm-intel.enable_unrestricted_guest=1, as + guest state is never invalid for unrestricted guests. + This param doesn't apply to nested guests (L2), as KVM + never emulates invalid L2 guest state. + Default is 1 (enabled) kvm-intel.flexpriority= [KVM,Intel] Disable FlexPriority feature (TPR shadow).
Greg Kroah-Hartman
maintainerPATCH 64/76 mm: mempolicy: fix THP allocations escaping mempolicy restrictions
In reply to Greg Kroah-HartmanFrom: Andrey Ryabinin <[email protected]>
commit 338635340669d5b317c7e8dcf4fff4a0f3651d87 upstream.
alloc_pages_vma() may try to allocate THP page on the local NUMA node first:
page = __alloc_pages_node(hpage_node, gfp | __GFP_THISNODE | __GFP_NORETRY, order);
And if the allocation fails it retries allowing remote memory:
if (!page && (gfp & __GFP_DIRECT_RECLAIM))
page = __alloc_pages_node(hpage_node,
gfp, order);However, this retry allocation completely ignores memory policy nodemask allowing allocation to escape restrictions.
The first appearance of this bug seems to be the commit ac5b2c18911f ("mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings").
The bug disappeared later in the commit 89c83fb539f9 ("mm, thp:
consolidate THP gfp handling into alloc_hugepage_direct_gfpmask") and reappeared again in slightly different form in the commit 76e654cc91bb ("mm, page_alloc: allow hugepage fallback to remote nodes when madvised")
Fix this by passing correct nodemask to the __alloc_pages() call.
The demonstration/reproducer of the problem:
$ mount -oremount,size=4G,huge=always /dev/shm/
$ echo always > /sys/kernel/mm/transparent_hugepage/defrag
$ cat mbind_thp.c
#include <unistd.h>
#include <sys/mman.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <assert.h>
#include <stdlib.h>
#include <stdio.h>
#include <numaif.h> #define SIZE 2ULL << 30
int main(int argc, char **argv)
{
int fd;
unsigned long long i;
char *addr;
pid_t pid;
char buf[100];
unsigned long nodemask = 1;
fd = open("/dev/shm/test", O_RDWR|O_CREAT);
assert(fd > 0);
assert(ftruncate(fd, SIZE) == 0);
addr = mmap(NULL, SIZE, PROT_READ|PROT_WRITE,
MAP_SHARED, fd, 0);
assert(mbind(addr, SIZE, MPOL_BIND, &nodemask, 2, MPOL_MF_STRICT|MPOL_MF_MOVE)==0);
for (i = 0; i < SIZE; i+=4096) {
addr[i] = 1;
}
pid = getpid();
snprintf(buf, sizeof(buf), "grep shm /proc/%d/numa_maps", pid);
system(buf);
sleep(10000);
return 0;
}
$ gcc mbind_thp.c -o mbind_thp -lnuma
$ numactl -H
available: 2 nodes (0-1)
node 0 cpus: 0 2
node 0 size: 1918 MB
node 0 free: 1595 MB
node 1 cpus: 1 3
node 1 size: 2014 MB
node 1 free: 1731 MB
node distances:
node 0 1
0: 10 20
1: 20 10
$ rm -f /dev/shm/test; taskset -c 0 ./mbind_thp
7fd970a00000 bind:0 file=/dev/shm/test dirty=524288 active=0 N0=396800 N1=127488 kernelpagesize_kB=4--- mm/mempolicy.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
mm/mempolicy.c +2 -2
@@ -2222,8 +2222,8 @@ alloc_pages_vma(gfp_t gfp, int order, st* memory with both reclaim and compact as well. */ if (!page && (gfp & __GFP_DIRECT_RECLAIM)) - page =__alloc_pages_node (hpage_node, - gfp, order); + page =__alloc_pages_nodemask (gfp, order, + hpage_node, nmask); goto out; }
Greg Kroah-Hartman
maintainerPATCH 65/76 Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312
In reply to Greg Kroah-HartmanFrom: Johnny Chuang <[email protected]>
commit 4ebfee2bbc1a9c343dd50565ba5ae249fac32267 upstream.
The eKTH3900/eKTH5312 series do not support the firmware update rules of Remark ID. Exclude these two series from checking it when updating the firmware in touch controllers.
--- drivers/input/touchscreen/elants_i2c.c | 46 ++++++++++++++++++++++++++++++++- 1 file changed, 45 insertions(+), 1 deletion(-)
drivers/input/touchscreen/elants_i2c.c +45 -1
@@ -109,6 +109,19 @@#define ELAN_POWERON_DELAY_USEC 500#define ELAN_RESET_DELAY_MSEC 20 +/* FW boot code version */ +#define BC_VER_H_BYTE_FOR_EKTH3900x1_I2C 0x72 +#define BC_VER_H_BYTE_FOR_EKTH3900x2_I2C 0x82 +#define BC_VER_H_BYTE_FOR_EKTH3900x3_I2C 0x92 +#define BC_VER_H_BYTE_FOR_EKTH5312x1_I2C 0x6D +#define BC_VER_H_BYTE_FOR_EKTH5312x2_I2C 0x6E +#define BC_VER_H_BYTE_FOR_EKTH5312cx1_I2C 0x77 +#define BC_VER_H_BYTE_FOR_EKTH5312cx2_I2C 0x78 +#define BC_VER_H_BYTE_FOR_EKTH5312x1_I2C_USB 0x67 +#define BC_VER_H_BYTE_FOR_EKTH5312x2_I2C_USB 0x68 +#define BC_VER_H_BYTE_FOR_EKTH5312cx1_I2C_USB 0x74 +#define BC_VER_H_BYTE_FOR_EKTH5312cx2_I2C_USB 0x75 +enum elants_state {ELAN_STATE_NORMAL ,ELAN_WAIT_QUEUE_HEADER ,
@@ -663,6 +676,37 @@ static int elants_i2c_validate_remark_idreturn 0 ; } +static bool elants_i2c_should_check_remark_id (struct elants_data *ts) +{ +struct i2c_client *client = ts->client; +const u8 bootcode_version = ts->iap_version; +bool check; + +/* I2C eKTH3900 and eKTH5312 are NOT support Remark ID */ +if ((bootcode_version == BC_VER_H_BYTE_FOR_EKTH3900x1_I2C) || + (bootcode_version == BC_VER_H_BYTE_FOR_EKTH3900x2_I2C) || + (bootcode_version == BC_VER_H_BYTE_FOR_EKTH3900x3_I2C) || + (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312x1_I2C) || + (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312x2_I2C) || + (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312cx1_I2C) || + (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312cx2_I2C) || + (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312x1_I2C_USB) || + (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312x2_I2C_USB) || + (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312cx1_I2C_USB) || + (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312cx2_I2C_USB)) { +dev_dbg (&client->dev, +"eKTH3900/eKTH5312(0x%02x) are not support remark id\n" , + bootcode_version); + check = false; + }else if (bootcode_version >=0x60 ) { + check = true; + }else { + check = false; + } + +return check; +} +static int elants_i2c_do_update_firmware (struct i2c_client *client,const struct firmware *fw,bool force)
@@ -676,7 +720,7 @@ static int elants_i2c_do_update_firmwareu16 send_id;int page, n_fw_pages;int error; -bool check_remark_id = ts->iap_version >=0x60 ; +bool check_remark_id =elants_i2c_should_check_remark_id (ts);/* Recovery mode detection! */ if (force) {
Greg Kroah-Hartman
maintainerPATCH 66/76 Input: i8042 - enable deferred probe quirk for ASUS UM325UA
In reply to Greg Kroah-HartmanFrom: Samuel Čavoj <[email protected]>
commit 44ee250aeeabb28b52a10397ac17ffb8bfe94839 upstream.
The ASUS UM325UA suffers from the same issue as the ASUS UX425UA, which is a very similar laptop. The i8042 device is not usable immediately after boot and fails to initialize, requiring a deferred retry.
Enable the deferred probe quirk for the UM325UA.
--- drivers/input/serio/i8042-x86ia64io.h | 7 +++++++ 1 file changed, 7 insertions(+)
drivers/input/serio/i8042-x86ia64io.h +7 -0
@@ -992,6 +992,13 @@ static const struct dmi_system_id __init DMI_MATCH(DMI_PRODUCT_NAME, "C504"), }, }, + { + /* ASUS ZenBook UM325UA */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."), + DMI_MATCH(DMI_PRODUCT_NAME, "ZenBook UX325UA_UM325UA"), + }, + }, { } };
Greg Kroah-Hartman
maintainerPATCH 67/76 Input: goodix - add id->model mapping for the "9111" model
In reply to Greg Kroah-HartmanFrom: Hans de Goede <[email protected]>
commit 81e818869be522bc8fa6f7df1b92d7e76537926c upstream.
Add d->model mapping for the "9111" model, this fixes uses using a wrong config_len of 240 bytes while the "9111" model uses only 186 bytes of config.
--- drivers/input/touchscreen/goodix.c | 1 + 1 file changed, 1 insertion(+)
drivers/input/touchscreen/goodix.c +1 -0
@@ -162,6 +162,7 @@ static const struct goodix_chip_id goodi { .id = "911", .data = >911_chip_data }, { .id = "9271", .data = >911_chip_data }, { .id = "9110", .data = >911_chip_data }, + { .id = "9111", .data = >911_chip_data }, { .id = "927", .data = >911_chip_data }, { .id = "928", .data = >911_chip_data },
Greg Kroah-Hartman
maintainerPATCH 68/76 ASoC: tas2770: Fix setting of high sample rates
In reply to Greg Kroah-HartmanFrom: Martin Povišer <[email protected]>
commit 80d5be1a057e05f01d66e986cfd34d71845e5190 upstream.
Although the codec advertises support for 176.4 and 192 ksps, without this fix setting those sample rates fails with EINVAL at hw_params time.
--- sound/soc/codecs/tas2770.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
sound/soc/codecs/tas2770.c +2 -2
@@ -291,11 +291,11 @@ static int tas2770_set_samplerate(struct ramp_rate_val =TAS2770_TDM_CFG_REG0_SMP_44_1KHZ |TAS2770_TDM_CFG_REG0_31_88_2_96KHZ ;break ; -case 19200 : +case 192000 : ramp_rate_val =TAS2770_TDM_CFG_REG0_SMP_48KHZ |TAS2770_TDM_CFG_REG0_31_176_4_192KHZ ;break ; -case 17640 : +case 176400 : ramp_rate_val =TAS2770_TDM_CFG_REG0_SMP_44_1KHZ |TAS2770_TDM_CFG_REG0_31_176_4_192KHZ ;break ;
Greg Kroah-Hartman
maintainerPATCH 69/76 ASoC: rt5682: fix the wrong jack type detected
In reply to Greg Kroah-HartmanFrom: Derek Fang <[email protected]>
commit 8deb34a90f06374fd26f722c2a79e15160f66be7 upstream.
Some powers were changed during the jack insert detection and clk's enable/disable in CCF.
If in parallel, the influence has a chance to detect the wrong jack type, so add a lock.
--- sound/soc/codecs/rt5682.c | 4 ++++ 1 file changed, 4 insertions(+)
sound/soc/codecs/rt5682.c +4 -0
@@ -924,6 +924,8 @@ int rt5682_headset_detect(struct snd_socunsigned int val, count;if (jack_insert) { +snd_soc_dapm_mutex_lock (dapm); +snd_soc_component_update_bits (component,RT5682_PWR_ANLG_1 ,RT5682_PWR_VREF2 |RT5682_PWR_MB ,RT5682_PWR_VREF2 |RT5682_PWR_MB );
@@ -968,6 +970,8 @@ int rt5682_headset_detect(struct snd_socsnd_soc_component_update_bits (component,RT5682_MICBIAS_2 ,RT5682_PWR_CLK25M_MASK |RT5682_PWR_CLK1M_MASK ,RT5682_PWR_CLK25M_PU |RT5682_PWR_CLK1M_PU ); + +snd_soc_dapm_mutex_unlock (dapm); }else {rt5682_enable_push_button_irq (component, false); snd_soc_component_update_bits(component, RT5682_CBJ_CTRL_1,
Greg Kroah-Hartman
maintainerPATCH 70/76 pinctrl: mediatek: fix global-out-of-bounds issue
In reply to Greg Kroah-HartmanFrom: Guodong Liu <[email protected]>
commit 2d5446da5acecf9c67db1c9d55ae2c3e5de01f8d upstream.
When eint virtual eint number is greater than gpio number, it maybe produce 'desc[eint_n]' size globle-out-of-bounds issue.
--- drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c +6 -2
@@ -280,8 +280,12 @@ static int mtk_xt_get_gpio_n(void *data, desc = (const struct mtk_pin_desc *)hw->soc->pins; *gpio_chip = &hw->chip; -/* Be greedy to guess first gpio_n is equal to eint_n */ -if (desc[eint_n].eint.eint_n == eint_n) +/* +* Be greedy to guess first gpio_n is equal to eint_n. +* Only eint virtual eint number is greater than gpio number. +*/ +if (hw->soc->npins > eint_n && + desc[eint_n].eint.eint_n == eint_n) *gpio_n = eint_n;else *gpio_n =mtk_xt_find_eint_num (hw, eint_n);
Greg Kroah-Hartman
maintainerPATCH 71/76 hwmom: (lm90) Fix citical alarm status for MAX6680/MAX6681
In reply to Greg Kroah-HartmanFrom: Guenter Roeck <[email protected]>
commit da7dc0568491104c7acb632e9d41ddce9aaabbb1 upstream.
Tests with a real chip and a closer look into the datasheet reveals that the local and remote critical alarm status bits are swapped for MAX6680/MAX6681.
--- drivers/hwmon/lm90.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)
drivers/hwmon/lm90.c +8 -2
@@ -190,6 +190,7 @@ enum chips { lm90, adm1032, lm99, lm86,#define LM90_HAVE_EXTENDED_TEMP (1 << 8)/* extended temperature support*/ #define LM90_PAUSE_FOR_CONFIG (1 << 9)/* Pause conversion for config */ #define LM90_HAVE_CRIT (1 << 10)/* Chip supports CRIT/OVERT register */ +#define LM90_HAVE_CRIT_ALRM_SWP (1 << 11)/* critical alarm bits swapped */ /* LM90 status */ #define LM90_STATUS_LTHRM (1 << 0)/* local THERM limit tripped */
@@ -415,7 +416,8 @@ static const struct lm90_params lm90_par .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, }, [max6680] = { - .flags = LM90_HAVE_OFFSET | LM90_HAVE_CRIT, + .flags =LM90_HAVE_OFFSET |LM90_HAVE_CRIT + | LM90_HAVE_CRIT_ALRM_SWP, .alert_alarms = 0x7c, .max_convrate = 7, },
@@ -1191,6 +1193,7 @@ static const u8 lm90_temp_emerg_index[3]static const u8 lm90_min_alarm_bits[3 ] = {5 ,3 ,11 };static const u8 lm90_max_alarm_bits[3 ] = {6 ,4 ,12 };static const u8 lm90_crit_alarm_bits[3 ] = {0 ,1 ,9 }; +static const u8 lm90_crit_alarm_bits_swapped[3 ] = {1 ,0 ,9 };static const u8 lm90_emergency_alarm_bits[3 ] = {15 ,13 ,14 };static const u8 lm90_fault_bits[3 ] = {0 ,2 ,10 };
@@ -1216,7 +1219,10 @@ static int lm90_temp_read(struct device *val = (data->alarms >> lm90_max_alarm_bits[channel]) &1 ;break ;case hwmon_temp_crit_alarm: - *val = (data->alarms >> lm90_crit_alarm_bits[channel]) &1 ; +if (data->flags &LM90_HAVE_CRIT_ALRM_SWP ) + *val = (data->alarms >> lm90_crit_alarm_bits_swapped[channel]) &1 ; +else + *val = (data->alarms >> lm90_crit_alarm_bits[channel]) &1 ;break ;case hwmon_temp_emergency_alarm: *val = (data->alarms >> lm90_emergency_alarm_bits[channel]) &1 ;
Greg Kroah-Hartman
maintainerPATCH 72/76 hwmon: (lm90) Do not report busy status bit as alarm
In reply to Greg Kroah-HartmanFrom: Guenter Roeck <[email protected]>
commit cdc5287acad9ede121924a9c9313544b80d15842 upstream.
Bit 7 of the status register indicates that the chip is busy doing a conversion. It does not indicate an alarm status. Stop reporting it as alarm status bit.
--- drivers/hwmon/lm90.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/hwmon/lm90.c +2 -1
@@ -200,6 +200,7 @@ enum chips { lm90, adm1032, lm99, lm86,#define LM90_STATUS_RHIGH (1 << 4)/* remote high temp limit tripped */ #define LM90_STATUS_LLOW (1 << 5)/* local low temp limit tripped */ #define LM90_STATUS_LHIGH (1 << 6)/* local high temp limit tripped */ +#define LM90_STATUS_BUSY (1 << 7)/* conversion is ongoing */ #define MAX6696_STATUS2_R2THRM (1 << 1)/* remote2 THERM limit tripped */ #define MAX6696_STATUS2_R2OPEN (1 << 2)/* remote2 is an open circuit */
@@ -819,7 +820,7 @@ static int lm90_update_device(struct dev val =lm90_read_reg (client,LM90_REG_R_STATUS );if (val <0 )return val; - data->alarms = val;/* lower 8 bit of alarms */ + data->alarms = val & ~LM90_STATUS_BUSY ;if (data->kind == max6696) { val =lm90_select_remote_channel (data,1 );
Greg Kroah-Hartman
maintainerPATCH 73/76 ax25: NPD bug when detaching AX25 device
In reply to Greg Kroah-HartmanFrom: Lin Ma <[email protected]>
commit 1ade48d0c27d5da1ccf4b583d8c5fc8b534a3ac8 upstream.
The existing cleanup routine implementation is not well synchronized with the syscall routine. When a device is detaching, below race could occur.
static int ax25_sendmsg(...) {
...
lock_sock()
ax25 = sk_to_ax25(sk);
if (ax25->ax25_dev == NULL) // CHECK
...
ax25_queue_xmit(skb, ax25->ax25_dev->dev); // USE
...
}
static void ax25_kill_by_device(...) {
...
if (s->ax25_dev == ax25_dev) {
s->ax25_dev = NULL;
...
}Other syscall functions like ax25_getsockopt, ax25_getname, ax25_info_show also suffer from similar races. To fix them, this patch introduce lock_sock() into ax25_kill_by_device in order to guarantee that the nullify action in cleanup routine cannot proceed when another socket request is pending.
--- net/ax25/af_ax25.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
net/ax25/af_ax25.c +3 -1
@@ -85,8 +85,10 @@ static void ax25_kill_by_device(struct n again:ax25_for_each (s, &ax25_list) {if (s->ax25_dev == ax25_dev) { - s->ax25_dev =NULL ;spin_unlock_bh (&ax25_list_lock); +lock_sock (s->sk); + s->ax25_dev =NULL ; +release_sock (s->sk);ax25_disconnect (s,ENETUNREACH );spin_lock_bh (&ax25_list_lock);
Greg Kroah-Hartman
maintainerPATCH 74/76 hamradio: defer ax25 kfree after unregister_netdev
In reply to Greg Kroah-HartmanFrom: Lin Ma <[email protected]>
commit 3e0588c291d6ce225f2b891753ca41d45ba42469 upstream.
There is a possible race condition (use-after-free) like below
(USE) | (FREE)
ax25_sendmsg |
ax25_queue_xmit |
dev_queue_xmit |
__dev_queue_xmit |
__dev_xmit_skb |
sch_direct_xmit | ...
xmit_one |
netdev_start_xmit | tty_ldisc_kill
__netdev_start_xmit | mkiss_close
ax_xmit | kfree
ax_encaps |
|Even though there are two synchronization primitives before the kfree:
1. wait_for_completion(&ax->dead). This can prevent the race with routines from mkiss_ioctl. However, it cannot stop the routine coming from upper layer, i.e., the ax25_sendmsg.
2. netif_stop_queue(ax->dev). It seems that this line of code aims to halt the transmit queue but it fails to stop the routine that already being xmit.
This patch reorder the kfree after the unregister_netdev to avoid the possible UAF as the unregister_netdev() is well synchronized and won't return if there is a running routine.
--- drivers/net/hamradio/mkiss.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/net/hamradio/mkiss.c +5 -4
@@ -792,13 +792,14 @@ static void mkiss_close(struct tty_struc*/ netif_stop_queue (ax->dev); -/* Free all AX25 frame buffers. */ -kfree (ax->rbuff); -kfree (ax->xbuff); - ax->tty =NULL ;unregister_netdev (ax->dev); + +/* Free all AX25 frame buffers after unreg. */ +kfree (ax->rbuff); +kfree (ax->xbuff); +free_netdev (ax->dev); }
Greg Kroah-Hartman
maintainerPATCH 75/76 hamradio: improve the incomplete fix to avoid NPD
In reply to Greg Kroah-HartmanFrom: Lin Ma <[email protected]>
commit b2f37aead1b82a770c48b5d583f35ec22aabb61e upstream.
The previous commit 3e0588c291d6 ("hamradio: defer ax25 kfree after unregister_netdev") reorder the kfree operations and unregister_netdev operation to prevent UAF.
This commit improves the previous one by also deferring the nullify of the ax->tty pointer. Otherwise, a NULL pointer dereference bug occurs. Partial of the stack trace is shown below.
BUG: kernel NULL pointer dereference, address: 0000000000000538 RIP: 0010:ax_xmit+0x1f9/0x400 ... Call Trace: dev_hard_start_xmit+0xec/0x320 sch_direct_xmit+0xea/0x240 __qdisc_run+0x166/0x5c0 __dev_queue_xmit+0x2c7/0xaf0 ax25_std_establish_data_link+0x59/0x60 ax25_connect+0x3a0/0x500 ? security_socket_connect+0x2b/0x40 __sys_connect+0x96/0xc0 ? __hrtimer_init+0xc0/0xc0 ? common_nsleep+0x2e/0x50 ? switch_fpu_return+0x139/0x1a0 __x64_sys_connect+0x11/0x20 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xa9
The crash point is shown as below
static void ax_encaps(...) {
...
set_bit(TTY_DO_WRITE_WAKEUP, &ax->tty->flags); // ax->tty = NULL!
...
}
By placing the nullify action after the unregister_netdev, the ax->tty pointer won't be assigned as NULL net_device framework layer is well synchronized.
--- drivers/net/hamradio/mkiss.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/hamradio/mkiss.c +2 -2
@@ -792,14 +792,14 @@ static void mkiss_close(struct tty_struc*/ netif_stop_queue (ax->dev); - ax->tty =NULL ; -unregister_netdev (ax->dev);/* Free all AX25 frame buffers after unreg. */ kfree (ax->rbuff);kfree (ax->xbuff); + ax->tty =NULL ; +free_netdev (ax->dev); }
Greg Kroah-Hartman
maintainerPATCH 76/76 phonet/pep: refuse to enable an unbound pipe
In reply to Greg Kroah-HartmanFrom: Rémi Denis-Courmont <[email protected]>
commit 75a2f31520095600f650597c0ac41f48b5ba0068 upstream.
This ioctl() implicitly assumed that the socket was already bound to a valid local socket name, i.e. Phonet object. If the socket was not bound, two separate problems would occur:
1) We'd send an pipe enablement request with an invalid source object.
2) Later socket calls could BUG on the socket unexpectedly being connected yet not bound to a valid object.
--- net/phonet/pep.c | 2 ++ 1 file changed, 2 insertions(+)
net/phonet/pep.c +2 -0
@@ -946,6 +946,8 @@ static int pep_ioctl(struct sock *sk, in ret = -EBUSY ; else if (sk->sk_state == TCP_ESTABLISHED) ret = -EISCONN ; + else if (!pn->pn_sk.sobject) + ret = -EADDRNOTAVAIL ; else ret =pep_sock_enable (sk,NULL ,0 );release_sock (sk);
Quoted 9 lines · Greg Kroah-Hartman
This is the start of the stable review cycle for the 5.10.89 release. There are 76 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Wed, 29 Dec 2021 15:13:09 +0000. Anything received after that time might be too late.
The whole patch series can be found in one patch at:
Quoted 8 lines
https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.10.89-rc1.gzor in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.gitlinux-5.10.y
and the diffstat can be found below.thanks,
greg k-h
On ARCH_BRCMSTB using 32-bit and 64-bit ARM kernels:
Signature · 1 line
Florian
Quoted 10 lines · Greg Kroah-Hartman
This is the start of the stable review cycle for the 5.10.89 release. There are 76 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Wed, 29 Dec 2021 15:13:09 +0000. Anything received after that time might be too late.
The whole patch series can be found in one patch at:
Quoted 8 lines
https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.10.89-rc1.gzor in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.gitlinux-5.10.y
and the diffstat can be found below.thanks,
greg k-h
Results from Linaro’s test farm.
No regressions on arm64, arm, x86_64, and i386.
## Build
* kernel: 5.10.89-rc1
* git: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
* git branch: linux-5.10.y
* git commit: 44b3abecd41b48c75aab8337849358703fa5d58d
* git describe: v5.10.88-77-g44b3abecd41b
* test details:
https://qa-reports.linaro.org/lkft/linux-stable-rc-linux-5.10.y/build/v5.10.88-77-g44b3abecd41b
## No Test Regressions (compared to v5.10.88-65-ga809519bc1d9)
## No Test Fixes (compared to v5.10.88-65-ga809519bc1d9)
## Test result summary
total: 98599, pass: 84552, fail: 547, skip: 12501, xfail: 999
## Build Summary
* arc: 10 total, 10 passed, 0 failed
* arm: 259 total, 255 passed, 4 failed
* arm64: 37 total, 37 passed, 0 failed
* dragonboard-410c: 1 total, 1 passed, 0 failed
* hi6220-hikey: 1 total, 1 passed, 0 failed
* i386: 36 total, 36 passed, 0 failed
* juno-r2: 1 total, 1 passed, 0 failed
* mips: 34 total, 30 passed, 4 failed
* parisc: 12 total, 12 passed, 0 failed
* powerpc: 52 total, 46 passed, 6 failed
* riscv: 24 total, 16 passed, 8 failed
* s390: 18 total, 18 passed, 0 failed
* sh: 24 total, 24 passed, 0 failed
* sparc: 12 total, 12 passed, 0 failed
* x15: 1 total, 1 passed, 0 failed
* x86: 1 total, 1 passed, 0 failed
* x86_64: 37 total, 37 passed, 0 failed
## Test suites summary
* build/gcc-11-https://github.com/raspberrypi/linux/raw/rpi-5.10.y/arch/arm/configs
* fwts
* kselftest-android
* kselftest-arm64
* kselftest-arm64/arm64.btitest.bti_c_func
* kselftest-arm64/arm64.btitest.bti_j_func
* kselftest-arm64/arm64.btitest.bti_jc_func
* kselftest-arm64/arm64.btitest.bti_none_func
* kselftest-arm64/arm64.btitest.nohint_func
* kselftest-arm64/arm64.btitest.paciasp_func
* kselftest-arm64/arm64.nobtitest.bti_c_func
* kselftest-arm64/arm64.nobtitest.bti_j_func
* kselftest-arm64/arm64.nobtitest.bti_jc_func
* kselftest-arm64/arm64.nobtitest.bti_none_func
* kselftest-arm64/arm64.nobtitest.nohint_func
* kselftest-arm64/arm64.nobtitest.paciasp_func
* kselftest-bpf
* kselftest-breakpoints
* kselftest-capabilities
* kselftest-cgroup
* kselftest-clone3
* kselftest-core
* kselftest-cpu-hotplug
* kselftest-cpufreq
* kselftest-drivers
* kselftest-efivarfs
* kselftest-filesystems
* kselftest-firmware
* kselftest-fpu
* kselftest-futex
* kselftest-gpio
* kselftest-intel_pstate
* kselftest-ipc
* kselftest-ir
* kselftest-kcmp
* kselftest-kexec
* kselftest-kvm
* kselftest-lib
* kselftest-livepatch
* kselftest-membarrier
* kselftest-memfd
* kselftest-memory-hotplug
* kselftest-mincore
* kselftest-mount
* kselftest-mqueue
* kselftest-net
* kselftest-netfilter
* kselftest-nsfs
* kselftest-openat2
* kselftest-pid_namespace
* kselftest-pidfd
* kselftest-proc
* kselftest-pstore
* kselftest-ptrace
* kselftest-rseq
* kselftest-rtc
* kselftest-seccomp
* kselftest-sigaltstack
* kselftest-size
* kselftest-splice
* kselftest-static_keys
* kselftest-sync
* kselftest-sysctl
* kselftest-tc-testing
* kselftest-timens
* kselftest-timers
* kselftest-tmpfs
* kselftest-tpm2
* kselftest-user
* kselftest-vm
* kselftest-x86
* kselftest-zram
* kunit
* kvm-unit-tests
* libgpiod
* libhugetlbfs
* linux-log-parser
* ltp-cap_bounds-tests
* ltp-commands-tests
* ltp-containers-tests
* ltp-controllers-tests
* ltp-cpuhotplug-tests
* ltp-crypto-tests
* ltp-cve-tests
* ltp-dio-tests
* ltp-fcntl-locktests-tests
* ltp-filecaps-tests
* ltp-fs-tests
* ltp-fs_bind-tests
* ltp-fs_perms_simple-tests
* ltp-fsx-tests
* ltp-hugetlb-tests
* ltp-io-tests
* ltp-ipc-tests
* ltp-math-tests
* ltp-mm-tests
* ltp-nptl-tests
* ltp-open-posix-tests
* ltp-pty-tests
* ltp-sched-tests
* ltp-securebits-tests
* ltp-syscalls-tests
* ltp-tracing-tests
* network-basic-tests
* packetdrill
* perf
* rcutorture
* ssuite
* v4l2-compliance
--
Linaro LKFT
https://lkft.linaro.org
Hi Greg,
Quoted 7 lines · Greg Kroah-Hartman
This is the start of the stable review cycle for the 5.10.89 release. There are 76 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Wed, 29 Dec 2021 15:13:09 +0000. Anything received after that time might be too late.
Build test:
mips (gcc version 11.2.1 20211214): 63 configs -> no new failure arm (gcc version 11.2.1 20211214): 105 configs -> no new failure arm64 (gcc version 11.2.1 20211214): 3 configs -> no failure x86_64 (gcc version 11.2.1 20211214): 4 configs -> no failure
Boot test:x86_64: Booted on my test laptop. No regression.x86_64: Booted on qemu. No regression. [1]
arm64: Booted on rpi4b (4GB model). No regression. [2]
[1]. https://openqa.qa.codethink.co.uk/tests/556
[2]. https://openqa.qa.codethink.co.uk/tests/559
--
Regards
Sudip
Quoted 8 lines · Greg Kroah-Hartman
This is the start of the stable review cycle for the 5.10.89 release. There are 76 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Wed, 29 Dec 2021 15:13:09 +0000. Anything received after that time might be too late.
Build results:
total: 159 pass: 159 fail: 0 Qemu test results: total: 472 pass: 472 fail: 0
Guenter
Quoted 9 lines · Greg Kroah-Hartman
This is the start of the stable review cycle for the 5.10.89 release. There are 76 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Wed, 29 Dec 2021 15:13:09 +0000. Anything received after that time might be too late.
The whole patch series can be found in one patch at:
Quoted 9 lines
https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.10.89-rc1.gzor in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.gitlinux-5.10.y
and the diffstat can be found below.thanks,
greg k-h
Compiled and booted on my test system. No dmesg regressions.
thanks,
-- Shuah
Quoted 9 lines · Greg Kroah-Hartman
This is the start of the stable review cycle for the 5.10.89 release. There are 76 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Wed, 29 Dec 2021 15:13:09 +0000. Anything received after that time might be too late.
The whole patch series can be found in one patch at:
Quoted 9 lines
https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.10.89-rc1.gzor in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.gitlinux-5.10.y
and the diffstat can be found below.thanks,
greg k-h
Tested on arm64 and x86 for 5.10.89-rc1,
Kernel repo:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
Branch: linux-5.10.y
Version: 5.10.89-rc1
Commit: 44b3abecd41b48c75aab8337849358703fa5d58d
Compiler: gcc version 7.3.0 (GCC)
arm64:
--------------------------------------------------------------------
Testcase Result Summary:
total: 9018
passed: 9018
failed: 0
timeout: 0
--------------------------------------------------------------------
x86:
--------------------------------------------------------------------
Testcase Result Summary:
total: 9018
passed: 9018
failed: 0
timeout: 0
--------------------------------------------------------------------