pinctrl: baytrail: Clear direct_irq_en flag on broken configs
Subsystems (3)
PATCH v2 1/1 pinctrl: baytrail: Clear direct_irq_en flag on broken configs
Some boards set the direct_irq_en flag in the conf0 register without setting any of the trigger bits. The direct_irq_en flag just means that the GPIO will send IRQs directly to the APIC instead of going through the shared interrupt for the GPIO controller, in order for the pin to be able to actually generate IRQs the trigger flags must still be set.
So having the direct_irq_en flag set without any trigger flags is non-sense, log a FW_BUG warning when encountering this and clear the flag so that a driver can actually use the pin as IRQ through gpiod_to_irq().
Specifically this allows the edt-ft5x06 touchscreen driver to use INT33FC:02 pin 3 as touchscreen IRQ on the Nextbook Ares 8 tablet, accompanied by the following new log message:
byt_gpio INT33FC:02: [Firmware Bug]: pin 3: direct_irq_en set without trigger, clearing
The new byt_direct_irq_sanity_check() function also checks that the pin is actually appointed to one of the 16 direct-IRQs which the GPIO controller support and on success prints debug msg like these:
byt_gpio INT33FC:02: Pin 0: uses direct IRQ 0 (APIC 67) byt_gpio INT33FC:02: Pin 15: uses direct IRQ 2 (APIC 69)
This is useful to figure out the GPIO pin belonging to ACPI resources like this one: "Interrupt () { 0x00000043 }" or the other way around.
---
Changes in v2:
- Add "FW_BUG pin %i: direct_irq_en set but no IRQ assigned, clearing" warning
--- drivers/pinctrl/intel/pinctrl-baytrail.c | 38 ++++++++++++++++++++++-- 1 file changed, 36 insertions(+), 2 deletions(-)
drivers/pinctrl/intel/pinctrl-baytrail.c +36 -2
@@ -32,6 +32,7 @@#define BYT_VAL_REG 0x008#define BYT_DFT_REG 0x00c#define BYT_INT_STAT_REG 0x800 +#define BYT_DIRECT_IRQ_REG 0x980#define BYT_DEBOUNCE_REG 0x9d0/* BYT_CONF0_REG register bits */
@@ -1465,6 +1466,34 @@ static void byt_gpio_irq_handler(struct irq_desc *desc) chip->irq_eoi (data); } +static bool byt_direct_irq_sanity_check (struct intel_pinctrl *vg,int pin,u32 value) +{ +void __iomem *reg; +int i, j; + +if (!(value & (BYT_TRIG_POS |BYT_TRIG_NEG ))) { +dev_warn (vg->dev, +FW_BUG "pin %i: direct_irq_en set without trigger, clearing\n" , pin); +return false; + } + + reg = vg->communities->pad_regs +BYT_DIRECT_IRQ_REG ; +for (i =0 ; i <16 ; i +=4 ) { + value =readl (reg + i); +for (j =0 ; j <4 ; j++) { +if (((value >> j *8 ) &0xff ) == pin) { +dev_dbg (vg->dev,"Pin %i: uses direct IRQ %d (APIC %d)\n" , + pin, i + j,0x43 + i + j); +return true; + } + } + } + +dev_warn (vg->dev, +FW_BUG "pin %i: direct_irq_en set but no IRQ assigned, clearing\n" , pin); +return false; +} +static void byt_init_irq_valid_mask (struct gpio_chip *chip,unsigned long *valid_mask,unsigned int ngpios)
@@ -1492,8 +1521,13 @@ static void byt_init_irq_valid_mask(struct gpio_chip *chip, value =readl (reg);if (value &BYT_DIRECT_IRQ_EN ) { -clear_bit (i, valid_mask); -dev_dbg (vg->dev,"excluding GPIO %d from IRQ domain\n" , i); +if (byt_direct_irq_sanity_check (vg, i, value)) { +clear_bit (i, valid_mask); + }else { + value &= ~(BYT_DIRECT_IRQ_EN |BYT_TRIG_POS | +BYT_TRIG_NEG |BYT_TRIG_LVL ); +writel (value, reg); + } }else if ((value &BYT_PIN_MUX ) ==byt_get_gpio_mux (vg, i)) {byt_gpio_clear_triggering (vg, i);dev_dbg (vg->dev,"disabling GPIO %d\n" , i);
Signature · 1 line
2.33.1
Quoted 14 lines · Hans de Goede
Some boards set the
direct_irq_enflag in the conf0 register without setting any of the trigger bits. Thedirect_irq_enflag just means that the GPIO will send IRQs directly to the APIC instead of going through the shared interrupt for the GPIO controller, in order for the pin to be able to actually generate IRQs the trigger flags must still be set.So having the
direct_irq_enflag set without any trigger flags is non-sense, log aFW_BUGwarning when encountering this and clear the flag so that a driver can actually use the pin as IRQ throughgpiod_to_irq().Specifically this allows the edt-ft5x06 touchscreen driver to use INT33FC:02 pin 3 as touchscreen IRQ on the Nextbook Ares 8 tablet, accompanied by the following new log message:
Quoted 5 lines
byt_gpioINT33FC:02: [Firmware Bug]: pin 3:direct_irq_enset without trigger, clearingThe new
byt_direct_irq_sanity_check()function also checks that the pin is actually appointed to one of the 16 direct-IRQs which the GPIO controller support and on success prints debug msg like these:
supports ?
Quoted 6 lines
byt_gpioINT33FC:02: Pin 0: uses direct IRQ 0 (APIC 67)byt_gpioINT33FC:02: Pin 15: uses direct IRQ 2 (APIC 69)This is useful to figure out the GPIO pin belonging to ACPI resources like this one: "Interrupt () {
0x00000043}" or the other way around.
...
Quoted 7 lines
drivers/pinctrl/intel/pinctrl-baytrail.c +7
-0+static bool byt_direct_irq_sanity_check (struct intel_pinctrl *vg,int pin,u32 value) +{ +void __iomem *reg; +int i, j; + +if (!(value & (BYT_TRIG_POS |BYT_TRIG_NEG ))) { + dev_warn(vg->dev,
drivers/pinctrl/intel/pinctrl-baytrail.c static void byt_gpio_irq_handler(struct irq_desc *desc) · line 1484
Quoted 10 lines
drivers/pinctrl/intel/pinctrl-baytrail.c +9
-0+ FW_BUG "pin %i: direct_irq_en set without trigger, clearing\n", pin); +return false; + } + + reg = vg->communities->pad_regs +BYT_DIRECT_IRQ_REG ; +for (i =0 ; i <16 ; i +=4 ) { + value =readl (reg + i); +for (j =0 ; j <4 ; j++) { +if (((value >> j *8 ) &0xff ) == pin) {
Can it be like
u32 direct_irq[16]; void __iomem *reg; void *match; memcpy_fromio(...); match = memchr(...); if (match) dev_dbg(); else dev_warn(); return !!match;
?
Quoted 11 lines
drivers/pinctrl/intel/pinctrl-baytrail.c +11
-0+dev_dbg (vg->dev,"Pin %i: uses direct IRQ %d (APIC %d)\n" , + pin, i + j,0x43 + i + j); +return true; + } + } + } + +dev_warn (vg->dev, +FW_BUG "pin %i: direct_irq_en set but no IRQ assigned, clearing\n" , pin); +return false; +}
Signature · 2 lines
With Best Regards, Andy Shevchenko
Quoted 1 line · Andy Shevchenko
On Fri, Jan 07, 2022 at 03:23:43PM +0100, Hans de Goede wrote:
...
Quoted 34 lines
Quoted 7 lines
drivers/pinctrl/intel/pinctrl-baytrail.c +7
-0+static bool byt_direct_irq_sanity_check (struct intel_pinctrl *vg,int pin,u32 value) +{ +void __iomem *reg; +int i, j; + +if (!(value & (BYT_TRIG_POS |BYT_TRIG_NEG ))) { + dev_warn(vg->dev,drivers/pinctrl/intel/pinctrl-baytrail.c static void byt_gpio_irq_handler(struct irq_desc *desc) · line 1484
Quoted 10 lines
drivers/pinctrl/intel/pinctrl-baytrail.c +9
-0+ FW_BUG "pin %i: direct_irq_en set without trigger, clearing\n", pin); +return false; + } + + reg = vg->communities->pad_regs +BYT_DIRECT_IRQ_REG ; +for (i =0 ; i <16 ; i +=4 ) { + value =readl (reg + i); +for (j =0 ; j <4 ; j++) { +if (((value >> j *8 ) &0xff ) == pin) {Can it be like
u32 direct_irq[16]; void __iomem *reg; void *match; memcpy_fromio(...); match = memchr(...); if (match) dev_dbg(); else dev_warn(); return !!match;
Quoted 5 lines
?
drivers/pinctrl/intel/pinctrl-baytrail.c static void byt_gpio_irq_handler(struct irq_desc *desc) · line 1486
Quoted 3 lines
drivers/pinctrl/intel/pinctrl-baytrail.c +2
-0+dev_dbg (vg->dev,"Pin %i: uses direct IRQ %d (APIC %d)\n" , + pin, i + j,0x43 + i + j);
Why 0x43 is hard coded?
Quoted 9 lines
Quoted 9 lines
drivers/pinctrl/intel/pinctrl-baytrail.c +9
-0+return true; + } + } + } + +dev_warn (vg->dev, +FW_BUG "pin %i: direct_irq_en set but no IRQ assigned, clearing\n" , pin); +return false; +}
Signature · 2 lines
With Best Regards, Andy Shevchenko
Hi,
Quoted 15 lines · Andy Shevchenko
Quoted 14 lines · Hans de Goede
Some boards set the
direct_irq_enflag in the conf0 register without setting any of the trigger bits. Thedirect_irq_enflag just means that the GPIO will send IRQs directly to the APIC instead of going through the shared interrupt for the GPIO controller, in order for the pin to be able to actually generate IRQs the trigger flags must still be set.So having the
direct_irq_enflag set without any trigger flags is non-sense, log aFW_BUGwarning when encountering this and clear the flag so that a driver can actually use the pin as IRQ throughgpiod_to_irq().Specifically this allows the edt-ft5x06 touchscreen driver to use INT33FC:02 pin 3 as touchscreen IRQ on the Nextbook Ares 8 tablet, accompanied by the following new log message:
Quoted 7 lines
Quoted 5 lines
byt_gpioINT33FC:02: [Firmware Bug]: pin 3:direct_irq_enset without trigger, clearingThe new
byt_direct_irq_sanity_check()function also checks that the pin is actually appointed to one of the 16 direct-IRQs which the GPIO controller support and on success prints debug msg like these:supports ?
Ack, fixed for v3.
Quoted 43 lines
Quoted 6 lines
byt_gpioINT33FC:02: Pin 0: uses direct IRQ 0 (APIC 67)byt_gpioINT33FC:02: Pin 15: uses direct IRQ 2 (APIC 69)This is useful to figure out the GPIO pin belonging to ACPI resources like this one: "Interrupt () {
0x00000043}" or the other way around....
Quoted 7 lines
drivers/pinctrl/intel/pinctrl-baytrail.c +7
-0+static bool byt_direct_irq_sanity_check (struct intel_pinctrl *vg,int pin,u32 value) +{ +void __iomem *reg; +int i, j; + +if (!(value & (BYT_TRIG_POS |BYT_TRIG_NEG ))) { + dev_warn(vg->dev,drivers/pinctrl/intel/pinctrl-baytrail.c static void byt_gpio_irq_handler(struct irq_desc *desc) · line 1484
Quoted 10 lines
drivers/pinctrl/intel/pinctrl-baytrail.c +9
-0+ FW_BUG "pin %i: direct_irq_en set without trigger, clearing\n", pin); +return false; + } + + reg = vg->communities->pad_regs +BYT_DIRECT_IRQ_REG ; +for (i =0 ; i <16 ; i +=4 ) { + value =readl (reg + i); +for (j =0 ; j <4 ; j++) { +if (((value >> j *8 ) &0xff ) == pin) {Can it be like
u32 direct_irq[16]; void __iomem *reg; void *match; memcpy_fromio(...); match = memchr(...); if (match) dev_dbg(); else dev_warn(); return !!match;
Quoted 1 line
?
Yes that is a good idea, I've changed to this for v3.
Quoted 6 lines
drivers/pinctrl/intel/pinctrl-baytrail.c static void byt_gpio_irq_handler(struct irq_desc *desc) · line 1486
Quoted 3 lines
drivers/pinctrl/intel/pinctrl-baytrail.c +2
-0+dev_dbg (vg->dev,"Pin %i: uses direct IRQ %d (APIC %d)\n" , + pin, i + j,0x43 + i + j);Why
0x43is hard coded?
I noticed that at least for the 'INT33FC:02' controller, which seems to be the only one on which direct-IRQs get used, the direct-irq 0 slot corresponds to ACPI resource which points to the APIC IRQ 0x43:
"Interrupt () { 0x00000043 }", and slot 1 points to 0x44, etc.
But I'm not sure what if any the APIC IRQ offset is for the other GPIO islands, so I've just dropped the (APIC %d) part of the log msg for v3.
Regards,
Hans