imx8mm_venice: switch to use binman to pack images
Subsystems (3)
PATCH RESEND v3 1/1 imx8mm_venice: switch to use binman to pack images
Use binman to pack images.
Note that imx8mm_venice supports several boards via multiple DTB's thus in the fit node we must use:
- fit,fdt-list = "of-list"
- fdt-SEQ
- config-SEQ
Signed-off-by Tim Harvey <[email protected]>
Reviewed-by Marcel Ziswiler <[email protected]>
---
v3:
- resent as I forgot to include the uboot list
- rebase on top of Marcel's patch:
"arm64: dts: imx8mm: use common binman configuration"
v2:
- rebase on origin/mater
- remove ATF_LOAD_ADDR from README as its no longer needed
--- arch/arm/mach-imx/imx8m/Kconfig | 1 + board/gateworks/venice/Kconfig | 3 +-- board/gateworks/venice/README | 2 +- board/gateworks/venice/imximage-8mm-lpddr4.cfg | 9 +++++++++ configs/imx8mm_venice_defconfig | 4 ++-- 5 files changed, 14 insertions(+), 5 deletions(-) create mode 100644 board/gateworks/venice/imximage-8mm-lpddr4.cfg
arch/arm/mach-imx/imx8m/Kconfig +1 -0
@@ -73,6 +73,7 @@ config TARGET_IMX8MM_ICORE_MX8MM config TARGET_IMX8MM_VENICE bool "Support Gateworks Venice iMX8M Mini module" + select BINMAN select IMX8MM select SUPPORT_SPL select IMX8M_LPDDR4
board/gateworks/venice/Kconfig +1 -2
@@ -10,6 +10,5 @@ config SYS_CONFIG_NAME default "imx8mm_venice" config IMX_CONFIG - default "arch/arm/mach-imx/imx8m/imximage-8mm-lpddr4.cfg" - + default "board/gateworks/venice/imximage-8mm-lpddr4.cfg" endif
board/gateworks/venice/README +1 -1
@@ -25,7 +25,7 @@ $ cp firmware-imx-8.9/firmware/ddr/synopsys/lpddr4*.bin . Build U-Boot ============ $ make imx8mm_venice_defconfig -$ make flash.bin CROSS_COMPILE=aarch64-linux-gnu- ATF_LOAD_ADDR=0x920000 +$ make CROSS_COMPILE=aarch64-linux-gnu- Update eMMC ===========
board/gateworks/venice/imximage-8mm-lpddr4.cfg new file +9 -0
@@ -0,0 +1,9 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2021 Gateworks Corporation + */ + +#define __ASSEMBLY__ + +BOOT_FROM sd +LOADER u-boot-spl-ddr.bin 0x7E1000
configs/imx8mm_venice_defconfig +2 -2
@@ -25,7 +25,7 @@ CONFIG_SYS_LOAD_ADDR=0x40480000 CONFIG_FIT=y CONFIG_FIT_EXTERNAL_OFFSET=0x3000 CONFIG_SPL_LOAD_FIT=y -CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" +# CONFIG_USE_SPL_FIT_GENERATOR is not set CONFIG_OF_BOARD_SETUP=y CONFIG_OF_SYSTEM_SETUP=y # CONFIG_USE_BOOTCOMMAND is not set
@@ -56,7 +56,7 @@ CONFIG_CMD_EXT4_WRITE=y # CONFIG_SPL_EFI_PARTITION is not set CONFIG_OF_CONTROL=y CONFIG_SPL_OF_CONTROL=y -CONFIG_OF_LIST="imx8mm-venice-gw71xx-0x imx8mm-venice-gw72xx-0x imx8mm-venice-gw73xx-0x imx8mm-venice-gw7901 imx8mm-venice-gw7902" +CONFIG_OF_LIST="imx8mm-venice imx8mm-venice-gw71xx-0x imx8mm-venice-gw72xx-0x imx8mm-venice-gw73xx-0x imx8mm-venice-gw7901 imx8mm-venice-gw7902" CONFIG_ENV_IS_IN_MMC=y CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
Signature · 1 line
2.17.1
Quoted 10 lines · Tim Harvey
Use binman to pack images.
Note that
imx8mm_venicesupports several boards via multiple DTB's thus in the fit node we must use:
- fit,fdt-list = "of-list"
- fdt-SEQ
- config-SEQSigned-off-by Tim Harvey <[email protected]>Reviewed-by Marcel Ziswiler <[email protected]>
Applied to u-boot/master, thanks!
Signature · 1 line
Tom