phy: amlogic: fix shared reset control use
Subsystems (3)
v6 cover phy: amlogic: fix shared reset control use
This patchset fixes a usb suspend warning seen on the libretech-cc by using reset_control_rearm() call of the reset framework API. This call allows a reset consummer to release the reset line even when just triggered so that it may be triggered again by other reset consummers.
reset_control_(de)assert() calls are called, in some meson usb drivers, on a shared reset line when reset_control_reset has been used. This is not allowed by the reset framework.
Finally the meson usb drivers are updated to use this new call, which solves the suspend issue addressed by the previous reverted commit 7a410953d1fb ("usb: dwc3: meson-g12a: fix shared reset control use").
changes since v5:
- No changes.
Amjad Ouled-Ameur (3):
phy: amlogic: phy-meson-gxl-usb2: fix shared reset controller use
phy: amlogic: meson8b-usb2: Use dev_err_probe()
phy: amlogic: meson8b-usb2: fix shared reset control use
drivers/phy/amlogic/phy-meson-gxl-usb2.c | 5 ++++- drivers/phy/amlogic/phy-meson8b-usb2.c | 9 +++++++-- 2 files changed, 11 insertions(+), 3 deletions(-)
Signature · 1 line
2.25.1
PATCH v6 1/3 phy: amlogic: phy-meson-gxl-usb2: fix shared reset controller use
Use reset_control_rearm() call if an error occurs in case phy_meson_gxl_usb2_init() fails after reset() has been called ; or in case phy_meson_gxl_usb2_exit() is called i.e the resource is no longer used and the reset line may be triggered again by other devices.
reset_control_rearm() keeps use of triggered_count sane in the reset framework. Therefore, use of reset_control_reset() on shared reset line should be balanced with reset_control_rearm().
--- drivers/phy/amlogic/phy-meson-gxl-usb2.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/phy/amlogic/phy-meson-gxl-usb2.c +4 -1
@@ -114,8 +114,10 @@ static int phy_meson_gxl_usb2_init(struct phy *phy)return ret; ret =clk_prepare_enable (priv->clk); -if (ret) +if (ret) { +reset_control_rearm (priv->reset);return ret; + }return 0 ; }
@@ -125,6 +127,7 @@ static int phy_meson_gxl_usb2_exit(struct phy *phy)struct phy_meson_gxl_usb2_priv *priv =phy_get_drvdata (phy);clk_disable_unprepare (priv->clk); +reset_control_rearm (priv->reset);return 0 ; }
Signature · 1 line
2.25.1
PATCH v6 2/3 phy: amlogic: meson8b-usb2: Use dev_err_probe()
In reply to Amjad Ouled-AmeurUse the existing dev_err_probe() helper instead of open-coding the same operation.
--- drivers/phy/amlogic/phy-meson8b-usb2.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/phy/amlogic/phy-meson8b-usb2.c +3 -2
@@ -265,8 +265,9 @@ static int phy_meson8b_usb2_probe(struct platform_device *pdev)return PTR_ERR (priv->clk_usb); priv->reset =devm_reset_control_get_optional_shared (&pdev->dev,NULL ); -if (PTR_ERR (priv->reset) == -EPROBE_DEFER ) -return PTR_ERR (priv->reset); +if (IS_ERR (priv->reset)) +return dev_err_probe (&pdev->dev,PTR_ERR (priv->reset), +"Failed to get the reset line" ); priv->dr_mode =of_usb_get_dr_mode_by_phy (pdev->dev.of_node,-1 );if (priv->dr_mode ==USB_DR_MODE_UNKNOWN ) {
Signature · 1 line
2.25.1
PATCH v6 3/3 phy: amlogic: meson8b-usb2: fix shared reset control use
In reply to Amjad Ouled-AmeurUse reset_control_rearm() call if an error occurs in case phy_meson8b_usb2_power_on() fails after reset() has been called, or in case phy_meson8b_usb2_power_off() is called i.e the resource is no longer used and the reset line may be triggered again by other devices.
reset_control_rearm() keeps use of triggered_count sane in the reset framework, use of reset_control_reset() on shared reset line should be balanced with reset_control_rearm().
--- drivers/phy/amlogic/phy-meson8b-usb2.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/phy/amlogic/phy-meson8b-usb2.c +4 -0
@@ -154,6 +154,7 @@ static int phy_meson8b_usb2_power_on(struct phy *phy) ret =clk_prepare_enable (priv->clk_usb_general);if (ret) {dev_err (&phy->dev,"Failed to enable USB general clock\n" ); +reset_control_rearm (priv->reset);return ret; }
@@ -161,6 +162,7 @@ static int phy_meson8b_usb2_power_on(struct phy *phy)if (ret) {dev_err (&phy->dev,"Failed to enable USB DDR clock\n" );clk_disable_unprepare (priv->clk_usb_general); +reset_control_rearm (priv->reset);return ret; }
@@ -199,6 +201,7 @@ static int phy_meson8b_usb2_power_on(struct phy *phy)dev_warn (&phy->dev,"USB ID detect failed!\n" );clk_disable_unprepare (priv->clk_usb);clk_disable_unprepare (priv->clk_usb_general); +reset_control_rearm (priv->reset);return -EINVAL ; } }
@@ -218,6 +221,7 @@ static int phy_meson8b_usb2_power_off(struct phy *phy)clk_disable_unprepare (priv->clk_usb);clk_disable_unprepare (priv->clk_usb_general); +reset_control_rearm (priv->reset);/* power off the PHY by putting it into reset mode */ regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_POWER_ON_RESET,
Signature · 1 line
2.25.1
Quoted 6 lines · Amjad Ouled-Ameur
This patchset fixes a usb suspend warning seen on the libretech-cc by using
reset_control_rearm()call of the reset framework API. This call allows a reset consummer to release the reset line even when just triggered so that it may be triggered again by other reset consummers.
Quoted 8 lines
reset_control_(de)assert() calls are called, in some meson usb drivers, on a shared reset line when
reset_control_resethas been used. This is not allowed by the reset framework.Finally the meson usb drivers are updated to use this new call, which solves the suspend issue addressed by the previous reverted commit
7a410953d1fb("usb: dwc3: meson-g12a: fix shared reset control use").
Applied, thanks
Signature · 1 line
~Vinod