Skip to contentSkip to conversation

serial: stm32: fix software flow control

PATCH New Valentin Caron 1 participant 3 messages Jan 11, 2022

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover serial: stm32: fix software flow control

This serie fix issues on STM32 USART driver when using software flow control.

Valentin Caron (2):
serial: stm32: prevent TDR register overwrite when sending x_char
serial: stm32: fix software flow control transfer

 drivers/tty/serial/stm32-usart.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)
Signature · 1 line
2.17.1
#1 lore raw

PATCH 1/2 serial: stm32: prevent TDR register overwrite when sending x_char

When sending x_char in stm32_usart_transmit_chars(), driver can overwrite the value of TDR register by the value of x_char. If this happens, the previous value that was present in TDR register will not be sent through uart.

This code checks if the previous value in TDR register is sent before writing the x_char value into register.

Fixes 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
---
 drivers/tty/serial/stm32-usart.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
drivers/tty/serial/stm32-usart.c +12 -0
index 1f89ab0e49ac..c1b8828451c8 100644
@@ -550,11 +550,23 @@ static void stm32_usart_transmit_chars(struct uart_port *port)
 	struct stm32_port *stm32_port = to_stm32_port(port);
 	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 	struct circ_buf *xmit = &port->state->xmit;
+	u32 isr;
+	int ret;
 
 	if (port->x_char) {
 		if (stm32_usart_tx_dma_started(stm32_port) &&
 		    stm32_usart_tx_dma_enabled(stm32_port))
 			stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_DMAT);
+
+		/* Check that TDR is empty before filling FIFO */
+		ret =
+		readl_relaxed_poll_timeout_atomic(port->membase + ofs->isr,
+						  isr,
+						  (isr & USART_SR_TXE),
+						  10, 1000);
+		if (ret)
+			dev_warn(port->dev, "1 character may be erased\n");
+
 		writel_relaxed(port->x_char, port->membase + ofs->tdr);
 		port->x_char = 0;
 		port->icount.tx++;
Signature · 1 line
2.17.1
#2 lore raw

PATCH 2/2 serial: stm32: fix software flow control transfer

In reply to Valentin Caron

x_char is ignored by stm32_usart_start_tx() when xmit buffer is empty.

Fix start_tx condition to allow x_char to be sent.

Fixes 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
---
 drivers/tty/serial/stm32-usart.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/tty/serial/stm32-usart.c +1 -1
index c1b8828451c8..9570002d07e7 100644
@@ -742,7 +742,7 @@ static void stm32_usart_start_tx(struct uart_port *port)
 	struct serial_rs485 *rs485conf = &port->rs485;
 	struct circ_buf *xmit = &port->state->xmit;
 
-	if (uart_circ_empty(xmit))
+	if (uart_circ_empty(xmit) && !port->x_char)
 		return;
 
 	if (rs485conf->flags & SER_RS485_ENABLED) {
Signature · 1 line
2.17.1