Skip to contentSkip to conversation

Add support for mp5023 device from Monolithic Power Systems, Inc. (MPS) vendor. This is a Hot-Swap Controller.

PATCH New Potin Lai 1 participant 1 message Jan 12, 2022

Subsystems (2)
lore
Share & tools
lore

Potin Lai

author
#0 lore raw

PATCH 1/1 Add support for mp5023 device from Monolithic Power Systems, Inc. (MPS) vendor. This is a Hot-Swap Controller.

From: Howard Chiu <[email protected]>

---
 Documentation/hwmon/mp5023.rst | 84 ++++++++++++++++++++++++++++++++++
 drivers/hwmon/pmbus/Kconfig    |  9 ++++
 drivers/hwmon/pmbus/Makefile   |  1 +
 drivers/hwmon/pmbus/mp5023.c   | 66 ++++++++++++++++++++++++++
 4 files changed, 160 insertions(+)
 create mode 100644 Documentation/hwmon/mp5023.rst
 create mode 100644 drivers/hwmon/pmbus/mp5023.c
Documentation/hwmon/mp5023.rst new file +84 -0
new file mode 100644
index 000000000000..af5ab1345a91
@@ -0,0 +1,84 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver mp5023
+====================
+
+Supported chips:
+
+  * MPS MP5023
+
+    Prefix: 'mp5023'
+
+  * Datasheet
+
+    Publicly available at the MPS website : https://www.monolithicpower.com/en/mp5023.html
+
+Author:
+
+	Howard Chiu <[email protected]>
+
+Description
+-----------
+
+This driver implements support for Monolithic Power Systems, Inc. (MPS)
+MP5023 Hot-Swap Controller.
+
+Device complaint with:
+
+- PMBus rev 1.3 interface.
+
+Device supports direct format for reading input voltage, output voltage,
+output current, input power and temperature.
+
+The driver exports the following attributes via the 'sysfs' files
+for input voltage:
+
+**in1_input**
+
+**in1_label**
+
+**in1_max**
+
+**in1_max_alarm**
+
+**in1_min**
+
+**in1_min_alarm**
+
+The driver provides the following attributes for output voltage:
+
+**in2_input**
+
+**in2_label**
+
+**in2_alarm**
+
+The driver provides the following attributes for output current:
+
+**curr1_input**
+
+**curr1_label**
+
+**curr1_alarm**
+
+**curr1_max**
+
+The driver provides the following attributes for input power:
+
+**power1_input**
+
+**power1_label**
+
+**power1_alarm**
+
+The driver provides the following attributes for temperature:
+
+**temp1_input**
+
+**temp1_max**
+
+**temp1_max_alarm**
+
+**temp1_crit**
+
+**temp1_crit_alarm**
drivers/hwmon/pmbus/Kconfig +9 -0
index ffb609cee3a4..b56bd8542864 100644
@@ -276,6 +276,15 @@ config SENSORS_MP2975
 	  This driver can also be built as a module. If so, the module will
 	  be called mp2975.
 
+config SENSORS_MP5023
+	tristate "MPS MP5023"
+	help
+	  If you say yes here you get hardware monitoring support for MPS
+	  MP5023.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called mp5023.
+
 config SENSORS_PIM4328
 	tristate "Flex PIM4328 and compatibles"
 	help
drivers/hwmon/pmbus/Makefile +1 -0
index 0ed4d596a948..61cdc24b1309 100644
@@ -31,6 +31,7 @@ obj-$(CONFIG_SENSORS_MAX34440)	+= max34440.o
 obj-$(CONFIG_SENSORS_MAX8688)	+= max8688.o
 obj-$(CONFIG_SENSORS_MP2888)	+= mp2888.o
 obj-$(CONFIG_SENSORS_MP2975)	+= mp2975.o
+obj-$(CONFIG_SENSORS_MP5023)	+= mp5023.o
 obj-$(CONFIG_SENSORS_PM6764TR)	+= pm6764tr.o
 obj-$(CONFIG_SENSORS_PXE1610)	+= pxe1610.o
 obj-$(CONFIG_SENSORS_Q54SJ108A2)	+= q54sj108a2.o
drivers/hwmon/pmbus/mp5023.c new file +66 -0

66 lines not on this page · raw message

Signature · 1 line
2.17.1