Skip to contentSkip to conversation

arm: dts: imx8mm-beacon: Resync dtsi with Kernel 5.17-rc1

PATCH Superseded Adam Ford 1 participant 2 messages Jan 14, 2022

Subsystems (2)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore

Adam Ford

author
#0 lore raw

PATCH 1/2 arm: dts: imx8mm-beacon: Resync dtsi with Kernel 5.17-rc1

Resync the SOM and baseboar files with the device trees that will be included in 5.17-RC1 when it's cut. This will improve pinmuxing for USDHC1 and add USB functionality.

arch/arm/dts/imx8mm-beacon-baseboard.dtsi +35 -1
index d6b9dedd16..4097a66163 100644
@@ -43,6 +43,17 @@
 		enable-active-high;
 	};
 
+	reg_usbotg1: regulator-usbotg1 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb_otg1>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	reg_usdhc2_vmmc: regulator-usdhc2 {
 		compatible = "regulator-fixed";
 		regulator-name = "VSD_3V3";
@@ -102,7 +113,6 @@
 		compatible = "wlf,wm8962";
 		reg = <0x1a>;
 		clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
-		clock-names = "xclk";
 		DCVDD-supply = <&reg_audio>;
 		DBVDD-supply = <&reg_audio>;
 		AVDD-supply = <&reg_audio>;
@@ -170,6 +180,24 @@
 	status = "okay";
 };
 
+&usbotg1 {
+	vbus-supply = <&reg_usbotg1>;
+	disable-over-current;
+	dr_mode="otg";
+	status = "okay";
+};
+
+&usbotg2 {
+	pinctrl-names = "default";
+	disable-over-current;
+	dr_mode="host";
+	status = "okay";
+};
+
+&usbphynop2 {
+	reset-gpios = <&pca6416_1 7 GPIO_ACTIVE_HIGH>;
+};
+
 &usdhc2 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
@@ -216,6 +244,12 @@
 		>;
 	};
 
+	pinctrl_reg_usb_otg1: usbotg1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_RXC_GPIO4_IO29     0x19
+		>;
+	};
+
 	pinctrl_sai3: sai3grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC     0xd6
arch/arm/dts/imx8mm-beacon-som.dtsi +4 -3
index d897913537..cf07987ccc 100644
@@ -91,7 +91,7 @@
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <80000000>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 	};
 };
@@ -256,12 +256,13 @@
 &usdhc1 {
 	#address-cells = <1>;
 	#size-cells = <0>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
 	bus-width = <4>;
 	non-removable;
 	cap-power-off-card;
-	pm-ignore-notify;
 	keep-power-in-suspend;
 	mmc-pwrseq = <&usdhc1_pwrseq>;
 	status = "okay";
Signature · 1 line
2.32.0
author
#1 lore raw

PATCH 2/2 imx: imx8mm_beacon: Enable USB

With the updated device tree's having USB support, enable in U-Boot. This also requires the addition of the imx8m power domain, since the USB is gated by the power domain controller.

configs/imx8mm_beacon_defconfig +13 -0
index bec90e9a9e..a5061e27d5 100644
@@ -45,6 +45,8 @@ CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_PART=y
 CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
@@ -96,6 +98,8 @@ CONFIG_MII=y
 CONFIG_PINCTRL=y
 CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_IMX8M=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_IMX8M_POWER_DOMAIN=y
 CONFIG_DM_PMIC=y
 CONFIG_DM_PMIC_BD71837=y
 CONFIG_SPL_DM_PMIC_BD71837=y
@@ -117,4 +121,13 @@ CONFIG_SYSRESET=y
 CONFIG_SPL_SYSRESET=y
 CONFIG_SYSRESET_PSCI=y
 CONFIG_DM_THERMAL=y
+CONFIG_USB=y
+# CONFIG_SPL_DM_USB is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
 # CONFIG_SPL_WDT is not set
Signature · 1 line
2.32.0