Skip to contentSkip to conversation

media: m88ds3103: Fix lock led support

PATCH New Michael Bunk 1 participant 4 messages Jan 16, 2022

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/4 media: m88ds3103: Fix lock led support

The new m88ds3101b demodulator version requires the highest bit of register 0x11 be cleared after tuning to a new frequency to make the lock output pin go high when a signal is found. This pin is normally connected to an indicator led.

---
 drivers/media/dvb-frontends/m88ds3103.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/media/dvb-frontends/m88ds3103.c +7 -0
index bce0f42f3d19..b5e3b4b81350 100644
@@ -1000,6 +1000,13 @@ static int m88ds3103_set_frontend(struct dvb_frontend *fe)
 	if (ret)
 		goto err;
 
+	if (dev->chiptype == M88DS3103_CHIPTYPE_3103B) {
+		/* to light up the LOCK led */
+		ret = m88ds3103_update_bits(dev, 0x11, 0x80, 0x00);
+		if (ret)
+			goto err;
+	}
+
 	dev->delivery_system = c->delivery_system;
 
 	return 0;
Signature · 1 line
2.34.1
#1 lore raw

PATCH 2/4 media: dw2102: Don't translate i2c read into write

The code ignored the I2C_M_RD flag on I2C messages. Instead it assumed an i2c transaction with a single message must be a write operation and a transaction with two messages would be a read operation.

Though this works for the driver code, it leads to problems once the i2c device is exposed to code not knowing this convention. For example, I did "insmod i2c-dev" and issued read requests from userspace, which were translated into write requests and destroyed the EEPROM of my device.

So, just check and respect the I2C_M_READ flag, which indicates a read when set on a message. If it is absent, it is a write message.

Incidentally, changing from the case statement to a while loop allows the code to lift the limitation to two i2c messages per transaction.

There are 4 more *_i2c_transfer functions affected by the same behaviour and limitation that should be fixed in the same way.

---
 drivers/media/usb/dvb-usb/dw2102.c | 120 ++++++++++++++++++-----------
 1 file changed, 73 insertions(+), 47 deletions(-)
drivers/media/usb/dvb-usb/dw2102.c +73 -47
index ca75ebdc10b3..60dd82f9dedc 100644
@@ -692,6 +692,7 @@ static int su3000_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg msg[],
 {
 	struct dvb_usb_device *d = i2c_get_adapdata(adap);
 	struct dw2102_state *state;
+	int j;
 
 	if (!d)
 		return -ENODEV;
@@ -705,11 +706,11 @@ static int su3000_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg msg[],
 		return -EAGAIN;
 	}
 
-	switch (num) {
-	case 1:
-		switch (msg[0].addr) {
+	j = 0;
+	while (j < num) {
+		switch (msg[j].addr) {
 		case SU3000_STREAM_CTRL:
-			state->data[0] = msg[0].buf[0] + 0x36;
+			state->data[0] = msg[j].buf[0] + 0x36;
 			state->data[1] = 3;
 			state->data[2] = 0;
 			if (dvb_usb_generic_rw(d, state->data, 3,
@@ -721,61 +722,86 @@ static int su3000_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg msg[],
 			if (dvb_usb_generic_rw(d, state->data, 1,
 					state->data, 2, 0) < 0)
 				err("i2c transfer failed.");
-			msg[0].buf[1] = state->data[0];
-			msg[0].buf[0] = state->data[1];
+			msg[j].buf[1] = state->data[0];
+			msg[j].buf[0] = state->data[1];
 			break;
 		default:
-			if (3 + msg[0].len > sizeof(state->data)) {
-				warn("i2c wr: len=%d is too big!\n",
-				     msg[0].len);
+			/* if the current write msg is followed by a another
+			 * read msg to/from the same address
+			 */
+			if ((j+1 < num) && (msg[j+1].flags & I2C_M_RD) &&
+			    (msg[j].addr == msg[j+1].addr)) {
+				/* join both i2c msgs to one usb read command */
+				if (4 + msg[j].len > sizeof(state->data)) {
+					warn("i2c combined wr/rd: write len=%d is too big!\n",
+					    msg[j].len);
+					num = -EOPNOTSUPP;
+					break;
+				}
+				if (1 + msg[j+1].len > sizeof(state->data)) {
+					warn("i2c combined wr/rd: read len=%d is too big!\n",
+					    msg[j+1].len);
+					num = -EOPNOTSUPP;
+					break;
+				}
+
+				state->data[0] = 0x09;
+				state->data[1] = msg[j].len;
+				state->data[2] = msg[j+1].len;
+				state->data[3] = msg[j].addr;
+				memcpy(&state->data[4], msg[j].buf, msg[j].len);
+
+				if (dvb_usb_generic_rw(d, state->data, msg[j].len + 4,
+					state->data, msg[j+1].len + 1, 0) < 0)
+					err("i2c transfer failed.");
+
+				memcpy(msg[j+1].buf, &state->data[1], msg[j+1].len);
+				j++;
+				break;
+			}
+
+			if (msg[j].flags & I2C_M_RD) {
+				/* single read */
+				if (1 + msg[j].len > sizeof(state->data)) {
+					warn("i2c rd: len=%d is too big!\n", msg[j].len);
+					num = -EOPNOTSUPP;
+					break;
+				}
+
+				state->data[0] = 0x09;
+				state->data[1] = 0;
+				state->data[2] = msg[j].len;
+				state->data[3] = msg[j].addr;
+				memcpy(&state->data[4], msg[j].buf, msg[j].len);
+
+				if (dvb_usb_generic_rw(d, state->data, 4,
+					state->data, msg[j].len + 1, 0) < 0)
+					err("i2c transfer failed.");
+
+				memcpy(msg[j].buf, &state->data[1], msg[j].len);
+				break;
+			}
+
+			/* single write */
+			if (3 + msg[j].len > sizeof(state->data)) {
+				warn("i2c wr: len=%d is too big!\n", msg[j].len);
 				num = -EOPNOTSUPP;
 				break;
 			}
 
-			/* always i2c write*/
 			state->data[0] = 0x08;
-			state->data[1] = msg[0].addr;
-			state->data[2] = msg[0].len;
+			state->data[1] = msg[j].addr;
+			state->data[2] = msg[j].len;
 
-			memcpy(&state->data[3], msg[0].buf, msg[0].len);
+			memcpy(&state->data[3], msg[j].buf, msg[j].len);
 
-			if (dvb_usb_generic_rw(d, state->data, msg[0].len + 3,
+			if (dvb_usb_generic_rw(d, state->data, msg[j].len + 3,
 						state->data, 1, 0) < 0)
 				err("i2c transfer failed.");
+		} // switch
+		j++;
 
-		}
-		break;
-	case 2:
-		/* always i2c read */
-		if (4 + msg[0].len > sizeof(state->data)) {
-			warn("i2c rd: len=%d is too big!\n",
-			     msg[0].len);
-			num = -EOPNOTSUPP;
-			break;
-		}
-		if (1 + msg[1].len > sizeof(state->data)) {
-			warn("i2c rd: len=%d is too big!\n",
-			     msg[1].len);
-			num = -EOPNOTSUPP;
-			break;
-		}
-
-		state->data[0] = 0x09;
-		state->data[1] = msg[0].len;
-		state->data[2] = msg[1].len;
-		state->data[3] = msg[0].addr;
-		memcpy(&state->data[4], msg[0].buf, msg[0].len);
-
-		if (dvb_usb_generic_rw(d, state->data, msg[0].len + 4,
-					state->data, msg[1].len + 1, 0) < 0)
-			err("i2c transfer failed.");
-
-		memcpy(msg[1].buf, &state->data[1], msg[1].len);
-		break;
-	default:
-		warn("more than 2 i2c messages at a time is not handled yet.");
-		break;
-	}
+	} // while
 	mutex_unlock(&d->data_mutex);
 	mutex_unlock(&d->i2c_mutex);
 	return num;
Signature · 1 line
2.34.1
#2 lore raw

PATCH 3/4 media: dw2102: Dont't list TT Cinergy S2 R4 twice

In reply to Michael Bunk

"modinfo dvb-usb-dw2102|grep 0105" returns two lines, because the module reports this usb alias twice.

Remove one of them.

---
 drivers/media/usb/dvb-usb/dw2102.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)
drivers/media/usb/dvb-usb/dw2102.c +1 -3
index 60dd82f9dedc..165d72d6d712 100644
@@ -1813,7 +1813,6 @@ enum dw2102_table_entry {
 	TECHNOTREND_S2_4600,
 	TEVII_S482_1,
 	TEVII_S482_2,
-	TERRATEC_CINERGY_S2_BOX,
 	TEVII_S662
 };
 
@@ -1852,7 +1851,6 @@ static struct usb_device_id dw2102_table[] = {
 		USB_PID_TECHNOTREND_CONNECT_S2_4600)},
 	[TEVII_S482_1] = {USB_DEVICE(0x9022, 0xd483)},
 	[TEVII_S482_2] = {USB_DEVICE(0x9022, 0xd484)},
-	[TERRATEC_CINERGY_S2_BOX] = {USB_DEVICE(USB_VID_TERRATEC, 0x0105)},
 	[TEVII_S662] = {USB_DEVICE(0x9022, USB_PID_TEVII_S662)},
 	{ }
 };
@@ -2563,7 +2561,7 @@ static struct dvb_usb_device_properties tt_s2_4600_properties = {
 			{ NULL },
 		},
 		{ "Terratec Cinergy S2 USB BOX",
-			{ &dw2102_table[TERRATEC_CINERGY_S2_BOX], NULL },
+			{ &dw2102_table[TERRATEC_CINERGY_S2_R4], NULL },
 			{ NULL },
 		},
 		{ "TeVii S662",
Signature · 1 line
2.34.1
#3 lore raw

PATCH 4/4 media: dw2102: Fix minor issues

In reply to Michael Bunk

Found by checkpatch.

---
 drivers/media/usb/dvb-usb/dw2102.c | 106 +++++++++++++++--------------
 1 file changed, 56 insertions(+), 50 deletions(-)
drivers/media/usb/dvb-usb/dw2102.c +56 -50
index 165d72d6d712..79a6675877a2 100644
@@ -53,10 +53,10 @@
 #define DW2102_FIRMWARE "dvb-usb-dw2102.fw"
 #define DW2104_FIRMWARE "dvb-usb-dw2104.fw"
 #define DW3101_FIRMWARE "dvb-usb-dw3101.fw"
-#define S630_FIRMWARE   "dvb-usb-s630.fw"
-#define S660_FIRMWARE   "dvb-usb-s660.fw"
-#define P1100_FIRMWARE  "dvb-usb-p1100.fw"
-#define P7500_FIRMWARE  "dvb-usb-p7500.fw"
+#define S630_FIRMWARE	"dvb-usb-s630.fw"
+#define S660_FIRMWARE	"dvb-usb-s660.fw"
+#define P1100_FIRMWARE	"dvb-usb-p1100.fw"
+#define P7500_FIRMWARE	"dvb-usb-p7500.fw"
 
 #define	err_str "did not find the firmware file '%s'. You can use <kernel_dir>/scripts/get_dvb_firmware to get the firmware"
 
@@ -87,7 +87,7 @@ MODULE_PARM_DESC(demod, "demod to probe (1=cx24116 2=stv0903+stv6110 4=stv0903+s
 DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
 
 static int dw210x_op_rw(struct usb_device *dev, u8 request, u16 value,
-			u16 index, u8 * data, u16 len, int flags)
+			u16 index, u8 *data, u16 len, int flags)
 {
 	int ret;
 	u8 *u8buf;
@@ -103,7 +103,7 @@ static int dw210x_op_rw(struct usb_device *dev, u8 request, u16 value,
 	if (flags == DW210X_WRITE_MSG)
 		memcpy(u8buf, data, len);
 	ret = usb_control_msg(dev, pipe, request, request_type | USB_TYPE_VENDOR,
-				value, index , u8buf, len, 2000);
+				value, index, u8buf, len, 2000);
 
 	if (flags == DW210X_READ_MSG)
 		memcpy(data, u8buf, len);
@@ -298,7 +298,7 @@ static int dw2102_earda_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg ms
 		dw210x_op_rw(d->udev, 0xc2, 0, 0,
 				obuf, msg[0].len + 2, DW210X_WRITE_MSG);
 		/* second read registers */
-		dw210x_op_rw(d->udev, 0xc3, 0xd1 , 0,
+		dw210x_op_rw(d->udev, 0xc3, 0xd1, 0,
 				ibuf, msg[1].len + 2, DW210X_READ_MSG);
 		memcpy(msg[1].buf, ibuf + 2, msg[1].len);
 
@@ -344,13 +344,15 @@ static int dw2102_earda_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg ms
 		}
 		case(DW2102_RC_QUERY): {
 			u8 ibuf[2];
+
 			dw210x_op_rw(d->udev, 0xb8, 0, 0,
 					ibuf, 2, DW210X_READ_MSG);
-			memcpy(msg[0].buf, ibuf , 2);
+			memcpy(msg[0].buf, ibuf, 2);
 			break;
 		}
 		case(DW2102_VOLTAGE_CTRL): {
 			u8 obuf[2];
+
 			obuf[0] = 0x30;
 			obuf[1] = msg[0].buf[0];
 			dw210x_op_rw(d->udev, 0xb2, 0, 0,
@@ -382,23 +384,26 @@ static int dw2104_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg msg[], i
 		switch (msg[j].addr) {
 		case(DW2102_RC_QUERY): {
 			u8 ibuf[2];
+
 			dw210x_op_rw(d->udev, 0xb8, 0, 0,
 					ibuf, 2, DW210X_READ_MSG);
-			memcpy(msg[j].buf, ibuf , 2);
+			memcpy(msg[j].buf, ibuf, 2);
 			break;
 		}
 		case(DW2102_VOLTAGE_CTRL): {
 			u8 obuf[2];
+
 			obuf[0] = 0x30;
 			obuf[1] = msg[j].buf[0];
 			dw210x_op_rw(d->udev, 0xb2, 0, 0,
 					obuf, 2, DW210X_WRITE_MSG);
 			break;
 		}
-		/*case 0x55: cx24116
-		case 0x6a: stv0903
-		case 0x68: ds3000, stv0903
-		case 0x60: ts2020, stv6110, stb6100 */
+		/* case 0x55: cx24116
+		 * case 0x6a: stv0903
+		 * case 0x68: ds3000, stv0903
+		 * case 0x60: ts2020, stv6110, stb6100
+		 */
 		default: {
 			if (msg[j].flags == I2C_M_RD) {
 				/* read registers */
@@ -423,6 +428,7 @@ static int dw2104_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg msg[], i
 						(msg[j].addr == 0x55))) {
 				/* write firmware */
 				u8 obuf[19];
+
 				obuf[0] = msg[j].addr << 1;
 				obuf[1] = (msg[j].len > 15 ? 17 : msg[j].len);
 				obuf[2] = msg[j].buf[0];
@@ -503,7 +509,7 @@ static int dw3101_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg msg[],
 		dw210x_op_rw(d->udev, 0xc2, 0, 0,
 				obuf, msg[0].len + 2, DW210X_WRITE_MSG);
 		/* second read registers */
-		dw210x_op_rw(d->udev, 0xc3, 0x19 , 0,
+		dw210x_op_rw(d->udev, 0xc3, 0x19, 0,
 				ibuf, msg[1].len + 2, DW210X_READ_MSG);
 		memcpy(msg[1].buf, ibuf + 2, msg[1].len);
 
@@ -531,9 +537,10 @@ static int dw3101_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg msg[],
 		}
 		case(DW2102_RC_QUERY): {
 			u8 ibuf[2];
+
 			dw210x_op_rw(d->udev, 0xb8, 0, 0,
 					ibuf, 2, DW210X_READ_MSG);
-			memcpy(msg[0].buf, ibuf , 2);
+			memcpy(msg[0].buf, ibuf, 2);
 			break;
 		}
 		}
@@ -570,6 +577,7 @@ static int s6x0_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg msg[],
 		switch (msg[j].addr) {
 		case (DW2102_RC_QUERY): {
 			u8 ibuf[5];
+
 			dw210x_op_rw(d->udev, 0xb8, 0, 0,
 					ibuf, 5, DW210X_READ_MSG);
 			memcpy(msg[j].buf, ibuf + 3, 2);
@@ -597,11 +605,12 @@ static int s6x0_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg msg[],
 					obuf, 2, DW210X_WRITE_MSG);
 			break;
 		}
-		/*case 0x55: cx24116
-		case 0x6a: stv0903
-		case 0x68: ds3000, stv0903, rs2000
-		case 0x60: ts2020, stv6110, stb6100
-		case 0xa0: eeprom */
+		/* case 0x55: cx24116
+		 * case 0x6a: stv0903
+		 * case 0x68: ds3000, stv0903, rs2000
+		 * case 0x60: ts2020, stv6110, stb6100
+		 * case 0xa0: eeprom
+		 */
 		default: {
 			if (msg[j].flags == I2C_M_RD) {
 				/* read registers */
@@ -623,6 +632,7 @@ static int s6x0_i2c_transfer(struct i2c_adapter *adap, struct i2c_msg msg[],
 						(msg[j].addr == 0x68)) {
 				/* write firmware */
 				u8 obuf[19];
+
 				obuf[0] = (msg[j].len > 16 ?
 						18 : msg[j].len + 1);
 				obuf[1] = msg[j].addr << 1;
@@ -854,13 +864,13 @@ static int dw210x_read_mac_address(struct dvb_usb_device *d, u8 mac[6])
 	u8 eeprom[256], eepromline[16];
 
 	for (i = 0; i < 256; i++) {
-		if (dw210x_op_rw(d->udev, 0xb6, 0xa0 , i, ibuf, 2, DW210X_READ_MSG) < 0) {
+		if (dw210x_op_rw(d->udev, 0xb6, 0xa0, i, ibuf, 2, DW210X_READ_MSG) < 0) {
 			err("read eeprom failed.");
 			return -1;
-		} else {
-			eepromline[i%16] = ibuf[0];
-			eeprom[i] = ibuf[0];
 		}
+		eepromline[i%16] = ibuf[0];
+		eeprom[i] = ibuf[0];
+
 		if ((i % 16) == 15) {
 			deb_xfer("%02x: ", i - 15);
 			debug_dump(eepromline, 16, deb_xfer);
@@ -896,11 +906,11 @@ static int s6x0_read_mac_address(struct dvb_usb_device *d, u8 mac[6])
 		if (ret != 2) {
 			err("read eeprom failed.");
 			return -1;
-		} else {
-			eepromline[i % 16] = ibuf[0];
-			eeprom[i] = ibuf[0];
 		}
 
+		eepromline[i % 16] = ibuf[0];
+		eeprom[i] = ibuf[0];
+
 		if ((i % 16) == 15) {
 			deb_xfer("%02x: ", i - 15);
 			debug_dump(eepromline, 16, deb_xfer);
@@ -973,8 +983,7 @@ static int su3000_read_mac_address(struct dvb_usb_device *d, u8 mac[6])
 		obuf[1] = 0xf0 + i;
 		if (i2c_transfer(&d->i2c_adap, msg, 2) != 2)
 			break;
-		else
-			mac[i] = ibuf[0];
+		mac[i] = ibuf[0];
 	}
 
 	return 0;
@@ -985,8 +994,6 @@ static int su3000_identify_state(struct usb_device *udev,
 				 const struct dvb_usb_device_description **desc,
 				 int *cold)
 {
-	info("%s", __func__);
-
 	*cold = 0;
 	return 0;
 }
@@ -1346,7 +1353,7 @@ static int stv0288_frontend_attach(struct dvb_usb_adapter *d)
 	if (d->fe_adap[0].fe == NULL)
 		return -EIO;
 
-	if (NULL == dvb_attach(stb6000_attach, d->fe_adap[0].fe, 0x61, &d->dev->i2c_adap))
+	if (dvb_attach(stb6000_attach, d->fe_adap[0].fe, 0x61, &d->dev->i2c_adap) == NULL)
 		return -EIO;
 
 	d->fe_adap[0].fe->ops.set_voltage = dw210x_set_voltage;
@@ -1889,7 +1896,7 @@ static int dw2102_load_firmware(struct usb_device *dev,
 		memcpy(p, fw->data, fw->size);
 		for (i = 0; i < fw->size; i += 0x40) {
 			b = (u8 *) p + i;
-			if (dw210x_op_rw(dev, 0xa0, i, 0, b , 0x40,
+			if (dw210x_op_rw(dev, 0xa0, i, 0, b, 0x40,
 					DW210X_WRITE_MSG) != 0x40) {
 				err("error while transferring firmware");
 				ret = -EINVAL;
@@ -1936,19 +1943,18 @@ static int dw2102_load_firmware(struct usb_device *dev,
 				dw2102_properties.i2c_algo = &dw2102_i2c_algo;
 				dw2102_properties.adapter->fe[0].tuner_attach = &dw2102_tuner_attach;
 				break;
-			} else {
-				/* check STV0288 frontend  */
-				reset16[0] = 0xd0;
-				reset16[1] = 1;
-				reset16[2] = 0;
-				dw210x_op_rw(dev, 0xc2, 0, 0, &reset16[0], 3,
-						DW210X_WRITE_MSG);
-				dw210x_op_rw(dev, 0xc3, 0xd1, 0, &reset16[0], 3,
-						DW210X_READ_MSG);
-				if (reset16[2] == 0x11) {
-					dw2102_properties.i2c_algo = &dw2102_earda_i2c_algo;
-					break;
-				}
+			}
+			/* check STV0288 frontend  */
+			reset16[0] = 0xd0;
+			reset16[1] = 1;
+			reset16[2] = 0;
+			dw210x_op_rw(dev, 0xc2, 0, 0, &reset16[0], 3,
+					DW210X_WRITE_MSG);
+			dw210x_op_rw(dev, 0xc3, 0xd1, 0, &reset16[0], 3,
+					DW210X_READ_MSG);
+			if (reset16[2] == 0x11) {
+				dw2102_properties.i2c_algo = &dw2102_earda_i2c_algo;
+				break;
 			}
 			fallthrough;
 		case 0x2101:
@@ -2575,15 +2581,15 @@ static int dw2102_probe(struct usb_interface *intf,
 		const struct usb_device_id *id)
 {
 	if (!(dvb_usb_device_init(intf, &dw2102_properties,
-			          THIS_MODULE, NULL, adapter_nr) &&
+				  THIS_MODULE, NULL, adapter_nr) &&
 	      dvb_usb_device_init(intf, &dw2104_properties,
 				  THIS_MODULE, NULL, adapter_nr) &&
 	      dvb_usb_device_init(intf, &dw3101_properties,
-			          THIS_MODULE, NULL, adapter_nr) &&
+				  THIS_MODULE, NULL, adapter_nr) &&
 	      dvb_usb_device_init(intf, &s6x0_properties,
-			          THIS_MODULE, NULL, adapter_nr) &&
+				  THIS_MODULE, NULL, adapter_nr) &&
 	      dvb_usb_device_init(intf, &p1100_properties,
-			          THIS_MODULE, NULL, adapter_nr) &&
+				  THIS_MODULE, NULL, adapter_nr) &&
 	      dvb_usb_device_init(intf, &s660_properties,
 				  THIS_MODULE, NULL, adapter_nr) &&
 	      dvb_usb_device_init(intf, &p7500_properties,
Signature · 1 line
2.34.1