Preparations to support SD UHS-II cards
v2 cover Preparations to support SD UHS-II cards
Series [1] that has been posted by Ulf Hansson which provided some guidance and an overall structure.
Series [2] focused on UHS-II card control side to address Ulf's intention regarding to "modularising" sd_uhs2.c.
Series [3] is based on series [2] and adopt most of Ulf's comments.
This series is the successor version of post [3], which adopts Ulf's comments about series [3]:
1. Remove unnecessary debug print.
2. Rephrase description about uhs2_cmd_assemble() in sd_uhs2.c
3. Place UHS-II variables in the appropriate structure.
4. Integrate 5 callback functions in host->uhs2_host_operation().
Kind regards
Jason Lai
[1]
https://patchwork.kernel.org/project/linux-mmc/list/?series=438509
[2]
https://patchwork.kernel.org/project/linux-mmc/list/?series=539737
[3]
https://patchwork.kernel.org/project/linux-mmc/list/?series=589827
Jason Lai (3):
mmc: add UHS-II related definitions in headers
mmc: Implement content of UHS-II card initialization functions
mmc: core: Support UHS-II card access
Ulf Hansson (4):
mmc: core: Cleanup printing of speed mode at card insertion
mmc: core: Prepare to support SD UHS-II cards
mmc: core: Announce successful insertion of an SD UHS-II card
mmc: core: Extend support for mmc regulators with a vqmmc2
drivers/mmc/core/Makefile | 2 +- drivers/mmc/core/bus.c | 38 +- drivers/mmc/core/core.c | 43 +- drivers/mmc/core/core.h | 1 + drivers/mmc/core/host.h | 4 + drivers/mmc/core/regulator.c | 34 ++ drivers/mmc/core/sd_uhs2.c | 1113 ++++++++++++++++++++++++++++++++++ include/linux/mmc/card.h | 35 ++ include/linux/mmc/core.h | 1 + include/linux/mmc/host.h | 68 +++ 10 files changed, 1319 insertions(+), 20 deletions(-) create mode 100644 drivers/mmc/core/sd_uhs2.c
Signature · 1 line
2.34.0
PATCH v2 1/7 mmc: core: Cleanup printing of speed mode at card insertion
From: Ulf Hansson <[email protected]>
The current print of the bus speed mode in mmc_add_card() has grown over the years and is now difficult to parse. Let's clean up the code and also take the opportunity to properly announce "DDR" for eMMCs as "high speed DDR", which is according to the eMMC spec.
--- drivers/mmc/core/bus.c | 36 ++++++++++++++++++++---------------- 1 file changed, 20 insertions(+), 16 deletions(-)
drivers/mmc/core/bus.c +20 -16
@@ -311,6 +311,7 @@ int mmc_add_card(struct mmc_card *card) {int ret;const char *type; +const char *speed_mode ="" ;const char *uhs_bus_speed_mode ="" ;static const char *const uhs_speeds[] = { [UHS_SDR12_BUS_SPEED ] ="SDR12 " ,
@@ -349,27 +350,30 @@ int mmc_add_card(struct mmc_card *card)break ; } +if (mmc_card_hs (card)) + speed_mode ="high speed " ; +else if (mmc_card_uhs (card)) + speed_mode ="ultra high speed " ; +else if (mmc_card_ddr52 (card)) + speed_mode ="high speed DDR " ; +else if (mmc_card_hs200 (card)) + speed_mode ="HS200 " ; +else if (mmc_card_hs400es (card)) + speed_mode ="HS400 Enhanced strobe " ; +else if (mmc_card_hs400 (card)) + speed_mode ="HS400 " ; +if (mmc_card_uhs (card) && (card->sd_bus_speed <ARRAY_SIZE (uhs_speeds))) uhs_bus_speed_mode = uhs_speeds[card->sd_bus_speed]; -if (mmc_host_is_spi (card->host)) { -pr_info ("%s: new %s%s%s card on SPI\n" , -mmc_hostname (card->host), -mmc_card_hs (card) ?"high speed " :"" , -mmc_card_ddr52 (card) ?"DDR " :"" , - type); - }else { -pr_info ("%s: new %s%s%s%s%s%s card at address %04x\n" , -mmc_hostname (card->host), -mmc_card_uhs (card) ?"ultra high speed " : - (mmc_card_hs (card) ?"high speed " :"" ), -mmc_card_hs400 (card) ?"HS400 " : - (mmc_card_hs200 (card) ?"HS200 " :"" ), -mmc_card_hs400es (card) ?"Enhanced strobe " :"" , -mmc_card_ddr52 (card) ?"DDR " :"" , +if (mmc_host_is_spi (card->host)) +pr_info ("%s: new %s%s card on SPI\n" , +mmc_hostname (card->host), speed_mode, type); +else +pr_info ("%s: new %s%s%s card at address %04x\n" , +mmc_hostname (card->host), speed_mode, uhs_bus_speed_mode, type, card->rca); - }#ifdef CONFIG_DEBUG_FS mmc_add_card_debugfs (card);
Signature · 1 line
2.34.0
PATCH v2 2/7 mmc: core: Prepare to support SD UHS-II cards
In reply to Jason LaiFrom: Ulf Hansson <[email protected]>
The SD UHS-II interface was introduced to the SD spec v4.00 several years ago. The interface is fundamentally different from an electrical and a protocol point of view, comparing to the legacy SD interface.
However, the legacy SD protocol is supported through a specific transport layer (SD-TRAN) defined in the UHS-II addendum of the spec. This allows the SD card to be managed in a very similar way as a legacy SD card, hence a lot of code can be re-used to support these new types of cards through the mmc subsystem.
Moreover, an SD card that supports the UHS-II interface shall also be backwards compatible with the legacy SD interface, which allows a UHS-II card to be inserted into a legacy slot. As a matter of fact, this is already supported by mmc subsystem as of today.
To prepare to add support for UHS-II, this change puts the basic foundation in the mmc core in place, allowing it to be more easily reviewed before subsequent changes implements the actual support.
Basically, the approach here adds a new UHS-II bus_ops type and adds a separate initialization path for the UHS-II card. The intent is to avoid us from sprinkling the legacy initialization path, but also to simplify implementation of the UHS-II specific bits.
At this point, there is only one new host ops added to manage the various ios settings needed for UHS-II. Additional host ops that are needed, are being added from subsequent changes.
--- drivers/mmc/core/Makefile | 2 +- drivers/mmc/core/core.c | 17 ++- drivers/mmc/core/core.h | 1 + drivers/mmc/core/sd_uhs2.c | 289 +++++++++++++++++++++++++++++++++++++ include/linux/mmc/card.h | 7 + include/linux/mmc/host.h | 23 +++ 6 files changed, 337 insertions(+), 2 deletions(-) create mode 100644 drivers/mmc/core/sd_uhs2.c
drivers/mmc/core/Makefile +1 -1
@@ -7,7 +7,7 @@ obj-$(CONFIG_MMC) += mmc_core.o mmc_core-y := core.o bus.o host.o \ mmc.o mmc_ops.o sd.o sd_ops.o \ sdio.o sdio_ops.o sdio_bus.o \ - sdio_cis.o sdio_io.o sdio_irq.o \ + sdio_cis.o sdio_io.o sdio_irq.o sd_uhs2.o\ slot-gpio.o regulator.o mmc_core-$(CONFIG_OF) += pwrseq.o obj-$(CONFIG_PWRSEQ_SIMPLE) += pwrseq_simple.o
drivers/mmc/core/core.c +16 -1
@@ -2194,6 +2194,18 @@ void mmc_rescan(struct work_struct *work) goto out; } +/* +* Ideally we should favor initialization of legacy SD cards and defer +* UHS-II enumeration. However, it seems like cards doesn't reliably +* announce their support for UHS-II in the response to the ACMD41, +* while initializing the legacy SD interface. Therefore, let's start +* with UHS-II for now. +*/ +if (!mmc_attach_sd_uhs2 (host)) { +mmc_release_host (host); + goto out; + } +for (i =0 ; i <ARRAY_SIZE (freqs); i++) {unsigned int freq = freqs[i];if (freq > host->f_max) {
@@ -2215,10 +2227,13 @@ void mmc_rescan(struct work_struct *work)void mmc_start_host (struct mmc_host *host) { +bool power_up = !(host->caps2 & + (MMC_CAP2_NO_PRESCAN_POWERUP |MMC_CAP2_SD_UHS2 )); + host->f_init =max (min (freqs[0 ], host->f_max), host->f_min); host->rescan_disable =0 ; -if (!(host->caps2 &MMC_CAP2_NO_PRESCAN_POWERUP )) { +if (power_up) {mmc_claim_host (host);mmc_power_up (host, host->ocr_avail);mmc_release_host (host);
drivers/mmc/core/core.h +1 -0
@@ -80,6 +80,7 @@ int mmc_detect_card_removed(struct mmc_host *host);int mmc_attach_mmc (struct mmc_host *host);int mmc_attach_sd (struct mmc_host *host);int mmc_attach_sdio (struct mmc_host *host); +int mmc_attach_sd_uhs2 (struct mmc_host *host);/* Module parameters */ extern bool use_spi_crc;
drivers/mmc/core/sd_uhs2.c new file +289 -0
289 lines not on this page · raw message
include/linux/mmc/card.h +7 -0
@@ -210,6 +210,11 @@ struct sd_ext_reg {#define SD_EXT_PERF_CMD_QUEUE (1<<4) }; +struct sd_uhs2_config { +u32 node_id; +/* TODO: Extend with more register configs. */ +}; +struct sdio_cccr {unsigned int sdio_vsn;unsigned int sd_vsn;
@@ -314,6 +319,8 @@ struct mmc_card {struct sd_ext_reg ext_power;/* SD extension reg for PM */ struct sd_ext_reg ext_perf;/* SD extension reg for PERF */ +struct sd_uhs2_config uhs2_config;/* SD UHS-II config */ +unsigned int sdio_funcs;/* number of SDIO functions */ atomic_t sdio_funcs_probed;/* number of probed SDIO funcs */ struct sdio_cccr cccr;/* common card info */
include/linux/mmc/host.h +23 -0
@@ -63,6 +63,10 @@ struct mmc_ios {#define MMC_TIMING_MMC_HS400 10#define MMC_TIMING_SD_EXP 11#define MMC_TIMING_SD_EXP_1_2V 12 +#define MMC_TIMING_SD_UHS2 13 + +unsigned char vqmmc2_voltage; +#define MMC_VQMMC2_VOLTAGE_180 0unsigned char signal_voltage;/* signalling voltage (1.8V or 3.3V) */
@@ -91,6 +95,10 @@ struct mmc_clk_phase_map {struct mmc_clk_phase phase[MMC_NUM_CLK_PHASES ]; }; +struct sd_uhs2_caps { +/* TODO: Add UHS-II capabilities for the host. */ +}; +struct mmc_host ;struct mmc_host_ops {
@@ -126,6 +134,18 @@ struct mmc_host_ops {*/ void (*set_ios)(struct mmc_host *host,struct mmc_ios *ios); +/* +* The uhs2_set_ios callback is mandatory to implement for hosts that +* supports the SD UHS-II interface (MMC_CAP2_SD_UHS2), while the +* callback is unused for the other cases. Note that, the struct +* mmc_ios is being re-used for this as well. +* +* Expected return values for the uhs2_set_ios callback are a negative +* errno in case of a failure or zero for success. +*/ +int (*uhs2_set_ios)(struct mmc_host *host,struct mmc_ios *ios); + +/* * Return values for the get_ro callback should be: * 0 for a read/write card
@@ -374,6 +394,7 @@ struct mmc_host { MMC_CAP2_HS200_1_2V_SDR)#define MMC_CAP2_SD_EXP (1 << 7)/* SD express via PCIe */ #define MMC_CAP2_SD_EXP_1_2V (1 << 8)/* SD express 1.2V */ +#define MMC_CAP2_SD_UHS2 (1 << 9)/* SD UHS-II support */ #define MMC_CAP2_CD_ACTIVE_HIGH (1 << 10)/* Card-detect signal active high */ #define MMC_CAP2_RO_ACTIVE_HIGH (1 << 11)/* Write-protect signal active high */ #define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14)/* Don't power up before scan */
@@ -399,6 +420,8 @@ struct mmc_host {#define MMC_CAP2_CRYPTO 0#endif +struct sd_uhs2_caps uhs2_caps;/* SD UHS-II capabilities */ +int fixed_drv_type;/* fixed driver type for non-removable media */ mmc_pm_flag_t pm_caps;/* supported pm features */
Signature · 1 line
2.34.0
PATCH v2 3/7 mmc: core: Announce successful insertion of an SD UHS-II card
In reply to Jason LaiFrom: Ulf Hansson <[email protected]>
To inform the users about SD UHS-II cards, let's extend the print at card insertion with a "UHS-II" substring. Within this change, it seems reasonable to convert from using "ultra high speed" into "UHS-I speed", for the UHS-I type, as it should makes it more clear.
Note that, the new print for UHS-II cards doesn't include the actual selected speed mode. Instead, this is going to be added from subsequent change.
--- drivers/mmc/core/bus.c | 4 +++- drivers/mmc/core/host.h | 4 ++++ 2 files changed, 7 insertions(+), 1 deletion(-)
drivers/mmc/core/bus.c +3 -1
@@ -353,7 +353,9 @@ int mmc_add_card(struct mmc_card *card)if (mmc_card_hs (card)) speed_mode ="high speed " ;else if (mmc_card_uhs (card)) - speed_mode ="ultra high speed " ; + speed_mode ="UHS-I speed " ; +else if (mmc_card_uhs2 (card)) + speed_mode ="UHS-II speed " ;else if (mmc_card_ddr52 (card)) speed_mode ="high speed DDR " ;else if (mmc_card_hs200 (card))
drivers/mmc/core/host.h +4 -0
@@ -83,5 +83,9 @@ static inline bool mmc_card_sd_express(struct mmc_host *host) host->ios.timing == MMC_TIMING_SD_EXP_1_2V; } +static inline bool mmc_card_uhs2 (struct mmc_card *card) +{ +return card->host->ios.timing ==MMC_TIMING_SD_UHS2 ; +}#endif
Signature · 1 line
2.34.0
PATCH v2 4/7 mmc: core: Extend support for mmc regulators with a vqmmc2
In reply to Jason LaiFrom: Ulf Hansson <[email protected]>
To allow an additional external regulator to be controlled by an mmc host driver, let's add support for a vqmmc2 regulator to the mmc core.
For an SD UHS-II interface the vqmmc2 regulator may correspond to the so called vdd2 supply, as described by the SD spec. Initially, only 1.8V is needed, hence limit the new helper function, mmc_regulator_set_vqmmc2() to this too.
Note that, to allow for flexibility mmc host drivers need to manage the enable/disable of the vqmmc2 regulator themselves, while the regulator is looked up through the common mmc_regulator_get_supply().
--- drivers/mmc/core/regulator.c | 34 ++++++++++++++++++++++++++++++++++ include/linux/mmc/host.h | 8 ++++++++ 2 files changed, 42 insertions(+)
drivers/mmc/core/regulator.c +34 -0
@@ -223,6 +223,33 @@ int mmc_regulator_set_vqmmc(struct mmc_host *mmc, struct mmc_ios *ios) }EXPORT_SYMBOL_GPL (mmc_regulator_set_vqmmc); +/** +* mmc_regulator_set_vqmmc2 - Set vqmmc2 as per the ios->vqmmc2_voltage +* @mmc: The mmc host to regulate +* @ios: The io bus settings +* +* Sets a new voltage level for the vqmmc2 regulator, which may correspond to +* the vdd2 regulator for an SD UHS-II interface. This function is expected to +* be called by mmc host drivers. +* +* Returns a negative error code on failure, zero if the voltage level was +* changed successfully or a positive value if the level didn't need to change. +*/ +int mmc_regulator_set_vqmmc2 (struct mmc_host *mmc,struct mmc_ios *ios) +{ +if (IS_ERR (mmc->supply.vqmmc2)) +return -EINVAL ; + +switch (ios->vqmmc2_voltage) { +case MMC_VQMMC2_VOLTAGE_180 : +return mmc_regulator_set_voltage_if_supported ( + mmc->supply.vqmmc2,1700000 ,1800000 ,1950000 ); +default : +return -EINVAL ; + } +} +EXPORT_SYMBOL_GPL (mmc_regulator_set_vqmmc2); +#else static inline int mmc_regulator_get_ocrmask (struct regulator *supply)
@@ -249,6 +276,7 @@ int mmc_regulator_get_supply(struct mmc_host *mmc) mmc->supply.vmmc =devm_regulator_get_optional (dev,"vmmc" ); mmc->supply.vqmmc =devm_regulator_get_optional (dev,"vqmmc" ); + mmc->supply.vqmmc2 =devm_regulator_get_optional (dev,"vqmmc2" );if (IS_ERR (mmc->supply.vmmc)) {if (PTR_ERR (mmc->supply.vmmc) == -EPROBE_DEFER )
@@ -268,6 +296,12 @@ int mmc_regulator_get_supply(struct mmc_host *mmc)dev_dbg (dev,"No vqmmc regulator found\n" ); } +if (IS_ERR (mmc->supply.vqmmc2)) { +if (PTR_ERR (mmc->supply.vqmmc2) == -EPROBE_DEFER ) +return -EPROBE_DEFER ; +dev_dbg (dev,"No vqmmc2 regulator found\n" ); + } +return 0 ; }EXPORT_SYMBOL_GPL (mmc_regulator_get_supply);
include/linux/mmc/host.h +8 -0
@@ -303,6 +303,7 @@ struct mmc_pwrseq;struct mmc_supply {struct regulator *vmmc;/* Card power supply */ struct regulator *vqmmc;/* Optional Vccq supply */ +struct regulator *vqmmc2;/* Optional supply for phy */ };struct mmc_ctx {
@@ -580,6 +581,7 @@ int mmc_regulator_set_ocr(struct mmc_host *mmc,struct regulator *supply, unsigned short vdd_bit);int mmc_regulator_set_vqmmc (struct mmc_host *mmc,struct mmc_ios *ios); +int mmc_regulator_set_vqmmc2 (struct mmc_host *mmc,struct mmc_ios *ios);#else static inline int mmc_regulator_set_ocr(struct mmc_host *mmc, struct regulator *supply,
@@ -593,6 +595,12 @@ static inline int mmc_regulator_set_vqmmc(struct mmc_host *mmc, {return -EINVAL ; } + +static inline int mmc_regulator_set_vqmmc2 (struct mmc_host *mmc, +struct mmc_ios *ios) +{ +return -EINVAL ; +}#endif int mmc_regulator_get_supply (struct mmc_host *mmc);
Signature · 1 line
2.34.0
PATCH v2 5/7 mmc: add UHS-II related definitions in headers
In reply to Jason LaiFrom: Jason Lai <[email protected]>
All LINK layer messages, registers and SD-TRAN command packet described in 'Part 1 UHS-II Addendum Ver 1.01' are defined in include/linux/mmc/sd_uhs2.h
drivers/mmc/core/sd_uhs2.h contains exported function prototype.
--- include/linux/mmc/card.h | 30 ++++++++++++++++++++++++++++- include/linux/mmc/core.h | 1 + include/linux/mmc/host.h | 41 ++++++++++++++++++++++++++++++++++++++-- 3 files changed, 69 insertions(+), 3 deletions(-)
include/linux/mmc/card.h +29 -1
@@ -212,7 +212,35 @@ struct sd_ext_reg {struct sd_uhs2_config {u32 node_id; -/* TODO: Extend with more register configs. */ + +u32 dap; +u32 gap; +u32 n_fcu; +u32 maxblk_len; +u8 n_lanes; +u8 dadr_len; +u8 app_type; +u8 phy_minor_rev; +u8 phy_major_rev; +u8 can_hibernate; +u8 n_lss_sync; +u8 n_lss_dir; +u8 link_minor_rev; +u8 link_major_rev; +u8 dev_type; +u8 n_data_gap; + +u32 n_fcu_set; +u32 maxblk_len_set; +u8 n_lanes_set; +u8 speed_range_set; +u8 n_lss_sync_set; +u8 n_lss_dir_set; +u8 n_data_gap_set; +u8 pwrctrl_mode_set; +u8 max_retry_set; + +u8 cfg_complete; };struct sdio_cccr {
include/linux/mmc/core.h +1 -0
@@ -2,6 +2,7 @@/* * linux/include/linux/mmc/core.h */ +#ifndef LINUX_MMC_CORE_H #define LINUX_MMC_CORE_H
include/linux/mmc/host.h +39 -2
59 lines not on this page · raw message
Signature · 1 line
2.34.0
PATCH v2 6/7 mmc: Implement content of UHS-II card initialization functions
In reply to Jason LaiFrom: Jason Lai <[email protected]>
UHS-II card initialization flow is divided into 2 categories: PHY & Card. Part 1 - PHY Initialization:
Every host controller may need their own avtivation operation to establish LINK between controller and card. So we add a new member function(uhs2_detect_init) in struct mmc_host_ops for host controller use.
Part 2 - Card Initialization:
This part can be divided into 6 substeps.
1. Send UHS-II CCMD DEVICE_INIT to card.
2. Send UHS-II CCMD ENUMERATE to card.
3. Send UHS-II Native Read CCMD to obtain capabilities in CFG_REG of card.
4. Host compares capabilities of host controller and card, then write the negotiated values to Setting field in CFG_REG of card through UHS-II Native Write CCMD.
5. Switch host controller's clock to Range B if it is supported by both host controller and card.
6. Execute legacy SD initialization flow.
Part 3 - Provide a function to tranaform legacy SD command packet into UHS-II
SD-TRAN DCMD packet.
Most of the code added above came from Intel's original patch[3].
[3]
https://patchwork.kernel.org/project/linux-mmc/patch/1419672479-30852-2-git-
[email protected]/
--- drivers/mmc/core/sd_uhs2.c | 860 ++++++++++++++++++++++++++++++++++++- 1 file changed, 842 insertions(+), 18 deletions(-)
drivers/mmc/core/sd_uhs2.c +842 -18
@@ -3,6 +3,7 @@* Copyright (C) 2021 Linaro Ltd * * Author: Ulf Hansson <[email protected]> +* Author: Jason Lai <[email protected]> * * Support for SD UHS-II cards */
@@ -10,19 +11,28 @@#include <linux/mmc/host.h> #include <linux/mmc/card.h> +#include <linux/mmc/sd_uhs2.h> #include "core.h" #include "bus.h" #include "sd.h" #include "mmc_ops.h" +#include "sd_uhs2.h" static const unsigned int sd_uhs2_freqs[] = {52000000 ,26000000 };static int sd_uhs2_set_ios (struct mmc_host *host) {struct mmc_ios *ios = &host->ios; +int err =0 ; -return host->ops->uhs2_set_ios (host, ios); +pr_debug ("%s: clock %uHz powermode %u Vdd %u timing %u\n" , +mmc_hostname (host), ios->clock, ios->power_mode, ios->vdd, + ios->timing); + + host->ops->set_ios (host, ios); + +return err; }static int sd_uhs2_power_up (struct mmc_host *host)
@@ -45,6 +55,43 @@ static void sd_uhs2_power_off(struct mmc_host *host)sd_uhs2_set_ios (host); } +/** +* sd_uhs2_cmd_assemble() - build up UHS-II command packet which is embeded in +* mmc_command structure +* @cmd: MMC command to executed +* @uhs2_cmd: UHS2 command corresponded to MMC command +* @header: Header field of UHS-II command cxpacket +* @arg: Argument field of UHS-II command packet +* @payload: Payload field of UHS-II command packet +* @plen: Payload length +* @resp: Response buffer is allocated by caller and it is used to keep +* the response of CM-TRAN command. For SD-TRAN command, uhs2_resp +* should be null and SD-TRAN command response should be stored in +* resp of mmc_command. +* @resp_len: Response buffer length +* +* The uhs2_command structure contains message packets which are transmited/ +* received on UHS-II bus. This function fills in the contents of uhs2_command +* structure and embededs UHS2 command into mmc_command structure, which is used +* in legacy SD operation functions. +* +*/ +static void sd_uhs2_cmd_assemble (struct mmc_command *cmd, +struct uhs2_command *uhs2_cmd, +u16 header,u16 arg, +u32 *payload,u8 plen,u8 *resp,u8 resp_len) +{ + uhs2_cmd->header = header; + uhs2_cmd->arg = arg; + uhs2_cmd->payload = payload; + uhs2_cmd->payload_len = plen *sizeof (u32); + uhs2_cmd->packet_len = uhs2_cmd->payload_len +4 ; + + cmd->uhs2_cmd = uhs2_cmd; + cmd->uhs2_resp = resp; + cmd->uhs2_resp_len = resp_len; +} +/* * Run the phy initialization sequence, which mainly relies on the UHS-II host * to check that we reach the expected electrical state, between the host and
@@ -52,7 +99,15 @@ static void sd_uhs2_power_off(struct mmc_host *host)*/ static int sd_uhs2_phy_init (struct mmc_host *host) { -return 0 ; +int err =0 ; + + err = host->ops->uhs2_host_operation(host, UHS2_DETECT_INIT) +if (err) { +pr_err ("%s: failed to initial phy for UHS-II!\n" , +mmc_hostname (host)); + } + +return err; }/*
@@ -61,6 +116,78 @@ static int sd_uhs2_phy_init(struct mmc_host *host)*/ static int sd_uhs2_dev_init (struct mmc_host *host) { +struct mmc_command cmd = {0 }; +struct uhs2_command uhs2_cmd = {}; +u32 cnt; +u32 dap, gap, resp_gap; +u16 header =0 , arg =0 ; +u32 payload[1 ]; +u8 plen =1 ; +u8 gd =0 , cf =1 ; +u8 resp[6 ] = {0 }; +u8 resp_len =6 ; +int err; + + dap = host->uhs2_caps.dap; + gap = host->uhs2_caps.gap; + + header =UHS2_NATIVE_PACKET |UHS2_PACKET_TYPE_CCMD ; + arg = ((UHS2_DEV_CMD_DEVICE_INIT &0xFF ) <<8 ) | +UHS2_NATIVE_CMD_WRITE | +UHS2_NATIVE_CMD_PLEN_4B | + (UHS2_DEV_CMD_DEVICE_INIT >>8 ); + +/* +* Refer to UHS-II Addendum Version 1.02 section 6.3.1. +* Max. time from DEVICE_INIT CCMD EOP reception on Device +* Rx to its SOP transmission on Device Tx(Tfwd_init_cmd) is +* 1 second. +*/ + cmd.busy_timeout =1000 ; + +/* +* Refer to UHS-II Addendum Version 1.02 section 6.2.6.3. +* When the number of the DEVICE_INIT commands is reach to +* 30 tiems, Host shall stop issuing DEVICE_INIT command +* and regard it as an error. +*/ +for (cnt =0 ; cnt <30 ; cnt++) { + payload[0 ] = ((dap &0xF ) <<12 ) | + (cf <<11 ) | + ((gd &0xF ) <<4 ) | + (gap &0xF ); + +sd_uhs2_cmd_assemble (&cmd, &uhs2_cmd, header, arg, + payload, plen, resp, resp_len); + + err =mmc_wait_for_cmd (host, &cmd,0 ); + +if (err) { +pr_err ("%s: %s: UHS2 CMD send fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return -EIO ; + } + +if (resp[3 ] != (UHS2_DEV_CMD_DEVICE_INIT &0xFF )) { +pr_err ("%s: DEVICE_INIT response is wrong!\n" , +mmc_hostname (host)); +return -EIO ; + } + +if (resp[5 ] &0x8 ) { + host->group_desc = gd; +break ; + } + resp_gap = resp[4 ] &0x0F ; +if (gap == resp_gap) + gd++; + } +if (cnt ==30 ) { +pr_err ("%s: DEVICE_INIT fail, already 30 times!\n" , +mmc_hostname (host)); +return -EIO ; + } +return 0 ; }
@@ -71,16 +198,169 @@ static int sd_uhs2_dev_init(struct mmc_host *host)*/ static int sd_uhs2_enum (struct mmc_host *host,u32 *node_id) { +struct mmc_command cmd = {0 }; +struct uhs2_command uhs2_cmd = {}; +u16 header =0 , arg =0 ; +u32 payload[1 ]; +u8 plen =1 ; +u8 id_f =0xF , id_l =0x0 ; +u8 resp[8 ] = {0 }; +u8 resp_len =8 ; +int err; + + header =UHS2_NATIVE_PACKET |UHS2_PACKET_TYPE_CCMD ; + arg = ((UHS2_DEV_CMD_ENUMERATE &0xFF ) <<8 ) | +UHS2_NATIVE_CMD_WRITE | +UHS2_NATIVE_CMD_PLEN_4B | + (UHS2_DEV_CMD_ENUMERATE >>8 ); + + payload[0 ] = (id_f <<4 ) | id_l; + +sd_uhs2_cmd_assemble (&cmd, &uhs2_cmd, header, arg, payload, plen, + resp, resp_len); + + err =mmc_wait_for_cmd (host, &cmd,0 ); +if (err) { +pr_err ("%s: %s: UHS2 CMD send fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return -EIO ; + } + +if (resp[3 ] != (UHS2_DEV_CMD_ENUMERATE &0xFF )) { +pr_err ("%s: ENUMERATE response is wrong!\n" , +mmc_hostname (host)); +return -EIO ; + } + + id_f = (resp[4 ] >>4 ) &0xF ; + id_l = resp[4 ] &0xF ; + *node_id = id_f; +return 0 ; }/* -* Read the UHS-II configuration registers (CFG_REG) of the card, by sending it -* commands and by parsing the responses. Store a copy of the relevant data in -* card->uhs2_config. +* Read the UHS-II configuration registers (CFG_REG) from card and store these +* configurations to card->uhs2_config. */ static int sd_uhs2_config_read (struct mmc_host *host,struct mmc_card *card) { +struct mmc_command cmd = {0 }; +struct uhs2_command uhs2_cmd = {}; +u16 header =0 , arg =0 ; +u32 cap; +int err; + + header =UHS2_NATIVE_PACKET | +UHS2_PACKET_TYPE_CCMD | + card->uhs2_config.node_id; + arg = ((UHS2_DEV_CONFIG_GEN_CAPS &0xFF ) <<8 ) | +UHS2_NATIVE_CMD_READ | +UHS2_NATIVE_CMD_PLEN_4B | + (UHS2_DEV_CONFIG_GEN_CAPS >>8 ); + +/* There is no payload because per spec, there should be +* no payload field for read CCMD. +* Plen is set in arg. Per spec, plen for read CCMD +* represents the len of read data which is assigned in payload +* of following RES (p136). +*/ +sd_uhs2_cmd_assemble (&cmd, &uhs2_cmd, header, arg,NULL ,0 ,NULL ,0 ); + + err =mmc_wait_for_cmd (host, &cmd,0 ); +if (err) { +pr_err ("%s: %s: UHS2 CMD send fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return err; + } + + cap = cmd.resp[0 ]; + card->uhs2_config.n_lanes = + (cap >>UHS2_DEV_CONFIG_N_LANES_POS ) & +UHS2_DEV_CONFIG_N_LANES_MASK ; + card->uhs2_config.dadr_len = + (cap >>UHS2_DEV_CONFIG_DADR_POS ) & +UHS2_DEV_CONFIG_DADR_MASK ; + card->uhs2_config.app_type = + (cap >>UHS2_DEV_CONFIG_APP_POS ) & +UHS2_DEV_CONFIG_APP_MASK ; + + arg = ((UHS2_DEV_CONFIG_PHY_CAPS &0xFF ) <<8 ) | +UHS2_NATIVE_CMD_READ | +UHS2_NATIVE_CMD_PLEN_8B | + (UHS2_DEV_CONFIG_PHY_CAPS >>8 ); + +sd_uhs2_cmd_assemble (&cmd, &uhs2_cmd, header, arg,NULL ,0 ,NULL ,0 ); + + err =mmc_wait_for_cmd (host, &cmd,0 ); +if (err) { +pr_err ("%s: %s: UHS2 CMD send fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return -EIO ; + } + + cap = cmd.resp[0 ]; + card->uhs2_config.phy_minor_rev = + cap &UHS2_DEV_CONFIG_PHY_MINOR_MASK ; + card->uhs2_config.phy_major_rev = + (cap >>UHS2_DEV_CONFIG_PHY_MAJOR_POS ) & +UHS2_DEV_CONFIG_PHY_MAJOR_MASK ; + card->uhs2_config.can_hibernate = + (cap >>UHS2_DEV_CONFIG_CAN_HIBER_POS ) & +UHS2_DEV_CONFIG_CAN_HIBER_MASK ; + + cap = cmd.resp[1 ]; + card->uhs2_config.n_lss_sync = + cap &UHS2_DEV_CONFIG_N_LSS_SYN_MASK ; + card->uhs2_config.n_lss_dir = + (cap >>UHS2_DEV_CONFIG_N_LSS_DIR_POS ) & +UHS2_DEV_CONFIG_N_LSS_DIR_MASK ; +if (card->uhs2_config.n_lss_sync ==0 ) + card->uhs2_config.n_lss_sync =16 <<2 ; +else + card->uhs2_config.n_lss_sync <<=2 ; + +if (card->uhs2_config.n_lss_dir ==0 ) + card->uhs2_config.n_lss_dir =16 <<3 ; +else + card->uhs2_config.n_lss_dir <<=3 ; + + arg = ((UHS2_DEV_CONFIG_LINK_TRAN_CAPS &0xFF ) <<8 ) | +UHS2_NATIVE_CMD_READ | +UHS2_NATIVE_CMD_PLEN_8B | + (UHS2_DEV_CONFIG_LINK_TRAN_CAPS >>8 ); + +sd_uhs2_cmd_assemble (&cmd, &uhs2_cmd, header, arg,NULL ,0 ,NULL ,0 ); + + err =mmc_wait_for_cmd (host, &cmd,0 ); +if (err) { +pr_err ("%s: %s: UHS2 CMD send fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return -EIO ; + } + + cap = cmd.resp[0 ]; + card->uhs2_config.link_minor_rev = + cap &UHS2_DEV_CONFIG_LT_MINOR_MASK ; + card->uhs2_config.link_major_rev = + (cap >>UHS2_DEV_CONFIG_LT_MAJOR_POS ) & +UHS2_DEV_CONFIG_LT_MAJOR_MASK ; + card->uhs2_config.n_fcu = + (cap >>UHS2_DEV_CONFIG_N_FCU_POS ) & +UHS2_DEV_CONFIG_N_FCU_MASK ; + card->uhs2_config.dev_type = + (cap >>UHS2_DEV_CONFIG_DEV_TYPE_POS ) & +UHS2_DEV_CONFIG_DEV_TYPE_MASK ; + card->uhs2_config.maxblk_len = + (cap >>UHS2_DEV_CONFIG_MAX_BLK_LEN_POS ) & +UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK ; + + cap = cmd.resp[1 ]; + card->uhs2_config.n_data_gap = + cap &UHS2_DEV_CONFIG_N_DATA_GAP_MASK ; +if (card->uhs2_config.n_fcu ==0 ) + card->uhs2_config.n_fcu =256 ; +return 0 ; }
@@ -95,6 +375,332 @@ static int sd_uhs2_config_read(struct mmc_host *host, struct mmc_card *card)*/ static int sd_uhs2_config_write (struct mmc_host *host,struct mmc_card *card) { +struct mmc_command cmd = {0 }; +struct uhs2_command uhs2_cmd = {}; +u16 header =0 , arg =0 ; +u32 payload[2 ]; +u8 nMinDataGap; +u8 plen; +u8 try; +int err; +u8 resp[5 ] = {0 }; +u8 resp_len =5 ; + + header =UHS2_NATIVE_PACKET | +UHS2_PACKET_TYPE_CCMD | card->uhs2_config.node_id; + arg = ((UHS2_DEV_CONFIG_GEN_SET &0xFF ) <<8 ) | +UHS2_NATIVE_CMD_WRITE | +UHS2_NATIVE_CMD_PLEN_8B | + (UHS2_DEV_CONFIG_GEN_SET >>8 ); + +if (card->uhs2_config.n_lanes ==UHS2_DEV_CONFIG_2L_HD_FD && + host->uhs2_caps.n_lanes ==UHS2_DEV_CONFIG_2L_HD_FD ) { +/* Support HD */ + host->uhs2_caps.flags |=MMC_UHS2_2L_HD ; + nMinDataGap =1 ; + }else { +/* Only support 2L-FD so far */ + host->uhs2_caps.flags &= ~MMC_UHS2_2L_HD ; + nMinDataGap =3 ; + } + +/* +* Most UHS-II cards only support FD and 2L-HD mode. Other lane numbers +* defined in UHS-II addendem Ver1.01 are optional. +*/ + host->uhs2_caps.n_lanes_set =UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD ; + card->uhs2_config.n_lanes_set =UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD ; + + plen =2 ; + payload[0 ] = card->uhs2_config.n_lanes_set << +UHS2_DEV_CONFIG_N_LANES_POS ; + payload[1 ] =0 ; + payload[0 ] =cpu_to_be32 (payload[0 ]); + payload[1 ] =cpu_to_be32 (payload[1 ]); + +/* +* There is no payload because per spec, there should be +* no payload field for read CCMD. +* Plen is set in arg. Per spec, plen for read CCMD +* represents the len of read data which is assigned in payload +* of following RES (p136). +*/ +sd_uhs2_cmd_assemble (&cmd, &uhs2_cmd, header, arg, payload, plen, +NULL ,0 ); + + err =mmc_wait_for_cmd (host, &cmd,0 ); +if (err) { +pr_err ("%s: %s: UHS2 CMD send fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return -EIO ; + } + + arg = ((UHS2_DEV_CONFIG_PHY_SET &0xFF ) <<8 ) | +UHS2_NATIVE_CMD_WRITE | +UHS2_NATIVE_CMD_PLEN_8B | + (UHS2_DEV_CONFIG_PHY_SET >>8 ); + +for (try =0 ; try <2 ; try++) { + plen =2 ; + +if (host->uhs2_caps.speed_range == +UHS2_DEV_CONFIG_PHY_SET_SPEED_B ) { + host->uhs2_caps.flags |=MMC_UHS2_SPEED_B ; + card->uhs2_config.speed_range_set = +UHS2_DEV_CONFIG_PHY_SET_SPEED_B ; + }else { + card->uhs2_config.speed_range_set = +UHS2_DEV_CONFIG_PHY_SET_SPEED_A ; + host->uhs2_caps.flags &= ~MMC_UHS2_SPEED_B ; + } + + payload[0 ] = card->uhs2_config.speed_range_set << +UHS2_DEV_CONFIG_PHY_SET_SPEED_POS ; + + card->uhs2_config.n_lss_sync_set = + (min (card->uhs2_config.n_lss_sync, + host->uhs2_caps.n_lss_sync) >>2 ) & +UHS2_DEV_CONFIG_N_LSS_SYN_MASK ; + host->uhs2_caps.n_lss_sync_set = + card->uhs2_config.n_lss_sync_set; + +if (try ==0 ) { + host->uhs2_caps.n_lss_dir_set = + (card->uhs2_config.n_lss_dir >>3 ) & +UHS2_DEV_CONFIG_N_LSS_DIR_MASK ; + card->uhs2_config.n_lss_dir_set = + ((host->uhs2_caps.n_lss_dir >>3 ) +1 ) & +UHS2_DEV_CONFIG_N_LSS_DIR_MASK ; + }else { + card->uhs2_config.n_lss_dir_set = + (max (card->uhs2_config.n_lss_dir, + host->uhs2_caps.n_lss_dir) >>3 ) & +UHS2_DEV_CONFIG_N_LSS_DIR_MASK ; + host->uhs2_caps.n_lss_dir_set = + card->uhs2_config.n_lss_dir_set; + } + + payload[1 ] = (card->uhs2_config.n_lss_dir_set << +UHS2_DEV_CONFIG_N_LSS_DIR_POS ) | + card->uhs2_config.n_lss_sync_set; + payload[0 ] =cpu_to_be32 (payload[0 ]); + payload[1 ] =cpu_to_be32 (payload[1 ]); + + resp_len =4 ; +memset (resp,0 ,sizeof (resp)); + +sd_uhs2_cmd_assemble (&cmd, &uhs2_cmd, header, arg, + payload, plen, resp, resp_len); + + err =mmc_wait_for_cmd (host, &cmd,0 ); +if (err) { +pr_err ("%s: %s: UHS2 CMD send fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return -EIO ; + } + +if (!(resp[2 ] &0x80 )) +break ; + } + + arg = ((UHS2_DEV_CONFIG_LINK_TRAN_SET &0xFF ) <<8 ) | +UHS2_NATIVE_CMD_WRITE | +UHS2_NATIVE_CMD_PLEN_8B | + (UHS2_DEV_CONFIG_LINK_TRAN_SET >>8 ); + + plen =2 ; + +if (card->uhs2_config.app_type ==UHS2_DEV_CONFIG_APP_SD_MEM ) + card->uhs2_config.maxblk_len_set = +UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN ; +else + card->uhs2_config.maxblk_len_set = +min (card->uhs2_config.maxblk_len, + host->uhs2_caps.maxblk_len); + host->uhs2_caps.maxblk_len_set = + card->uhs2_config.maxblk_len_set; + + card->uhs2_config.n_fcu_set = +min (card->uhs2_config.n_fcu, + host->uhs2_caps.n_fcu); + host->uhs2_caps.n_fcu_set = card->uhs2_config.n_fcu_set; + + card->uhs2_config.n_data_gap_set = +max (nMinDataGap, card->uhs2_config.n_data_gap); + host->uhs2_caps.n_data_gap_set = + card->uhs2_config.n_data_gap_set; + + host->uhs2_caps.max_retry_set =3 ; + card->uhs2_config.max_retry_set = host->uhs2_caps.max_retry_set; + + payload[0 ] = (card->uhs2_config.maxblk_len_set << +UHS2_DEV_CONFIG_MAX_BLK_LEN_POS ) | + (card->uhs2_config.max_retry_set << +UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS ) | + (card->uhs2_config.n_fcu_set << +UHS2_DEV_CONFIG_N_FCU_POS ); + payload[1 ] = card->uhs2_config.n_data_gap_set; + payload[0 ] =cpu_to_be32 (payload[0 ]); + payload[1 ] =cpu_to_be32 (payload[1 ]); + +sd_uhs2_cmd_assemble (&cmd, &uhs2_cmd, header, arg, payload, plen, +NULL ,0 ); + + err =mmc_wait_for_cmd (host, &cmd,0 ); +if (err) { +pr_err ("%s: %s: UHS2 CMD send fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return -EIO ; + } + + arg = ((UHS2_DEV_CONFIG_GEN_SET &0xFF ) <<8 ) | +UHS2_NATIVE_CMD_WRITE | +UHS2_NATIVE_CMD_PLEN_8B | + (UHS2_DEV_CONFIG_GEN_SET >>8 ); + + plen =2 ; + payload[0 ] =0 ; + payload[1 ] =UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE ; + payload[0 ] =cpu_to_be32 (payload[0 ]); + payload[1 ] =cpu_to_be32 (payload[1 ]); + + resp_len =5 ; +memset (resp,0 ,sizeof (resp)); +sd_uhs2_cmd_assemble (&cmd, &uhs2_cmd, header, arg, payload, plen, + resp, resp_len); + + err =mmc_wait_for_cmd (host, &cmd,0 ); +if (err) { +pr_err ("%s: %s: UHS2 CMD send fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return -EIO ; + } + +/* Set host Config Setting registers */ +if (!host->ops->uhs2_host_operation (host,UHS2_SET_CONFIG )) { +pr_err ("%s: %s: UHS2 SET_CONFIG fail!\n" , +mmc_hostname (host), __func__); +return -EIO ; + } + +return 0 ; +} + +static int sd_uhs2_go_dormant (struct mmc_host *host,bool hibernate,u32 node_id) +{ +struct mmc_command cmd = {0 }; +struct uhs2_command uhs2_cmd = {}; +u16 header =0 , arg =0 ; +u32 payload[1 ]; +u8 plen =1 ; +int err; + +/* Disable Normal INT */ +if (!host->ops->uhs2_host_operation (host,UHS2_DISABLE_INT )) { +pr_err ("%s: %s: UHS2 DISABLE_INT fail!\n" , +mmc_hostname (host), __func__); +return -EIO ; + } + + header =UHS2_NATIVE_PACKET |UHS2_PACKET_TYPE_CCMD | node_id; + + arg = ((UHS2_DEV_CMD_GO_DORMANT_STATE &0xFF ) <<8 ) | +UHS2_NATIVE_CMD_WRITE | +UHS2_NATIVE_CMD_PLEN_4B | + (UHS2_DEV_CMD_GO_DORMANT_STATE >>8 ); + +if (hibernate) + payload[0 ] =UHS2_DEV_CMD_DORMANT_HIBER ; + +sd_uhs2_cmd_assemble (&cmd, &uhs2_cmd, header, arg, payload, plen, +NULL ,0 ); + + err =mmc_wait_for_cmd (host, &cmd,0 ); +if (err) { +pr_err ("%s: %s: UHS2 CMD send fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return -EIO ; + } + +/* Check Dormant State in Present */ +if (!host->ops->uhs2_host_operation (host,UHS2_CHECK_DORMANT )) { +pr_err ("%s: %s: UHS2 GO_DORMANT_STATE fail!\n" , +mmc_hostname (host), __func__); +return -EIO ; + } + + host->ops->uhs2_host_operation (host,UHS2_DISABLE_CLK ); + +return 0 ; +} + +static int sd_uhs2_change_speed (struct mmc_host *host,u32 node_id) +{ +struct mmc_command cmd = {0 }; +struct uhs2_command uhs2_cmd = {}; +u16 header =0 , arg =0 ; +int err; +int timeout =100 ; + +/* Change Speed Range at controller side. */ +if (!host->ops->uhs2_host_operation (host,UHS2_SET_SPEED_B )) { +pr_err ("%s: %s: UHS2 SET_SPEED fail!\n" , +mmc_hostname (host), __func__); +return -EIO ; + } + + err =sd_uhs2_go_dormant (host, false, node_id); +if (err) { +pr_err ("%s: %s: UHS2 GO_DORMANT_STATE fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return -EIO ; + } + +/* restore sd clock */ +mmc_delay (5 ); + host->ops->uhs2_host_operation (host,UHS2_ENABLE_CLK ); + +/* Enable Normal INT */ +if (!host->ops->uhs2_host_operation (host,UHS2_ENABLE_INT )) { +pr_err ("%s: %s: UHS2 ENABLE_INT fail!\n" , +mmc_hostname (host), __func__); +return -EIO ; + } + +/* +* According to UHS-II Addendum Version 1.01, chapter 6.2.3, wait card +* switch to Active State +*/ + header =UHS2_NATIVE_PACKET |UHS2_PACKET_TYPE_CCMD | node_id; + arg = ((UHS2_DEV_CONFIG_GEN_SET &0xFF ) <<8 ) | +UHS2_NATIVE_CMD_READ | +UHS2_NATIVE_CMD_PLEN_8B | + (UHS2_DEV_CONFIG_GEN_SET >>8 ); +do { +sd_uhs2_cmd_assemble (&cmd, &uhs2_cmd, + header, arg, +NULL ,0 , +NULL ,0 ); + err =mmc_wait_for_cmd (host, &cmd,0 ); +if (err) { +pr_err ("%s: %s: UHS2 CMD send fail, err= 0x%x!\n" , +mmc_hostname (host), __func__, err); +return -EIO ; + } + +if (cmd.resp[1 ] &UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE ) +break ; + + timeout--; +if (timeout ==0 ) { +pr_err ("%s: %s: Not switch to Active in 100 ms\n" , +mmc_hostname (host->mmc), __func__); +return -EIO ; + } + +mmc_delay (1 ); + }while (1 ); +return 0 ; }
@@ -107,9 +713,127 @@ static int sd_uhs2_config_write(struct mmc_host *host, struct mmc_card *card)*/ static int sd_uhs2_legacy_init (struct mmc_host *host,struct mmc_card *card) { +int err; +u32 cid[4 ]; +u32 ocr; +u32 rocr =0 ; +int ro; + +WARN_ON (!host->claimed); + +/* Send CMD0 to reset SD card */ +mmc_go_idle (host); + +/* Send CMD8 to communicate SD interface operation condition */ + err =mmc_send_if_cond (host, host->ocr_avail); +if (err) { +pr_err ("%s: %s: SEND_IF_COND fail!\n" , +mmc_hostname (host), __func__); +return err; + } + +/* +* Probe SD card working voltage. +*/ + err =mmc_send_app_op_cond (host,0 , &ocr); +if (err) { +pr_err ("%s: %s: SD_SEND_OP_COND fail!\n" , +mmc_hostname (host), __func__); +return err; + } + card->ocr = ocr; + +/* +* Some SD cards claims an out of spec VDD voltage range. Let's treat +* these bits as being in-valid and especially also bit7. +*/ + ocr &= ~0x7FFF ; + rocr =mmc_select_voltage (host, ocr); + +/* +* Some cards have zero value of rocr in UHS-II mode. Assign host's +* ocr value to rocr. +*/ +if (!rocr) { +if (host->ocr_avail) { + rocr = host->ocr_avail; + }else { +pr_err ("%s: %s: there is no valid OCR.\n" , +mmc_hostname (host), __func__); +return -EINVAL ; + } + } + +/* Wait SD power on ready */ + ocr = rocr; + err =mmc_send_app_op_cond (host, ocr, &rocr); +if (err) { +pr_err ("%s: %s: SD_SEND_OP_COND fail!\n" ,mmc_hostname (host), + __func__); +return err; + } + + err =mmc_send_cid (host, cid); +if (err) { +pr_err ("%s: %s: SD_SEND_CID fail!\n" ,mmc_hostname (host), + __func__); +return err; + } +memcpy (card->raw_cid, cid,sizeof (card->raw_cid)); + +/* +* Call the optional HC's init_card function to handle quirks. +*/ +if (host->ops->init_card) + host->ops->init_card (host, card); + +/* +* For native busses: get card RCA and quit open drain mode. +*/ + err =mmc_send_relative_addr (host, &card->rca); +if (err) { +pr_err ("%s: %s: SD_SEND_RCA fail!\n" ,mmc_hostname (host), + __func__); +return err; + } + + err =mmc_sd_get_csd (card); +if (err) { +pr_err ("%s: %s: SD_SEND_CSD fail!\n" ,mmc_hostname (host), + __func__); +return err; + } + +/* +* Select card, as all following commands rely on that. +*/ + err =mmc_select_card (card); +if (err) { +pr_err ("%s: %s: SD_SEL_DSEL fail!\n" ,mmc_hostname (host), + __func__); +return err; + } + +/* +* Check if read-only switch is active. +*/ + ro =mmc_sd_get_ro (host); +if (ro <0 ) { + pr_warn("%s: host does not support reading read-only switch, + assuming write-enable\n", mmc_hostname(host)); + } else if (ro > 0) { + mmc_card_set_readonly(card); + } + return 0; } +static void sd_uhs2_remove (struct mmc_host *host) +{ +mmc_remove_card (host->card); + host->card =NULL ; +} +/* * Allocate the data structure for the mmc_card and run the UHS-II specific * initialization sequence.
@@ -121,16 +845,21 @@ static int sd_uhs2_init_card(struct mmc_host *host)int err; err =sd_uhs2_dev_init (host); -if (err) +if (err) { +pr_err ("%s: UHS2 DEVICE_INIT fail!\n" ,mmc_hostname (host));return err; + } err =sd_uhs2_enum (host, &node_id); -if (err) +if (err) { +pr_err ("%s: UHS2 ENUMERATE fail!\n" ,mmc_hostname (host));return err; + } card =mmc_alloc_card (host, &sd_type);if (IS_ERR (card))return PTR_ERR (card); + host->card = card; card->uhs2_config.node_id = node_id; card->type =MMC_TYPE_SD ;
@@ -139,6 +868,16 @@ static int sd_uhs2_init_card(struct mmc_host *host)if (err) goto err; +/* Change to Speed Range B if it is supported */ +if (host->uhs2_caps.flags &MMC_UHS2_SPEED_B ) { + err =sd_uhs2_change_speed (host, node_id); +if (err) { +pr_err ("%s: %s: UHS2 sd_uhs2_change_speed() fail!\n" , +mmc_hostname (host), __func__); +return err; + } + } + err =sd_uhs2_config_write (host, card);if (err) goto err;
@@ -147,20 +886,13 @@ static int sd_uhs2_init_card(struct mmc_host *host)if (err) goto err; - host->card = card;return 0 ; err: -mmc_remove_card (card); +sd_uhs2_remove (host);return err; } -static void sd_uhs2_remove (struct mmc_host *host) -{ -mmc_remove_card (host->card); - host->card =NULL ; -} -static int sd_uhs2_alive (struct mmc_host *host) {return mmc_send_status (host->card,NULL );
@@ -214,6 +946,78 @@ static int sd_uhs2_hw_reset(struct mmc_host *host)return 0 ; } +/* +* sd_uhs2_prepare_cmd - prepare for SD command packet +* @host: MMC host +* @mrq: MMC request +* +* Initialize and fill in a header and a payload of SD command packet. +* The caller should allocate uhs2_command in host->cmd->uhs2_cmd in +* advance. +* +* Return: 0 on success, non-zero error on failure +*/ +int sd_uhs2_prepare_cmd (struct mmc_host *host,struct mmc_request *mrq) +{ +struct mmc_command *cmd; +struct uhs2_command *uhs2_cmd; +u16 header =0 , arg =0 ; +u32 *payload; +u8 plen =0 ; + + cmd = mrq->cmd; + header = host->card->uhs2_config.node_id; +if ((cmd->flags &MMC_CMD_MASK ) ==MMC_CMD_ADTC ) + header |=UHS2_PACKET_TYPE_DCMD ; +else + header |=UHS2_PACKET_TYPE_CCMD ; + + arg = cmd->opcode <<UHS2_SD_CMD_INDEX_POS ; +if (host->uhs2_caps.flags &MMC_UHS2_APP_CMD ) { + arg |=UHS2_SD_CMD_APP ; + host->uhs2_caps.flags &= ~MMC_UHS2_APP_CMD ; + } + + uhs2_cmd = cmd->uhs2_cmd; + payload = uhs2_cmd->payload; + plen =2 ;/* at the maximum */ + +if ((cmd->flags &MMC_CMD_MASK ) ==MMC_CMD_ADTC && + !cmd->uhs2_tmode0_flag) { +if (host->uhs2_caps.flags &MMC_UHS2_2L_HD ) + arg |=UHS2_DCMD_2L_HD_MODE ; + + arg |=UHS2_DCMD_LM_TLEN_EXIST ; + +if (cmd->data->blocks ==1 && + cmd->data->blksz !=512 && + cmd->opcode !=MMC_READ_SINGLE_BLOCK && + cmd->opcode !=MMC_WRITE_BLOCK ) { + arg |=UHS2_DCMD_TLUM_BYTE_MODE ; + payload[1 ] =cpu_to_be32 (cmd->data->blksz); + }else { + payload[1 ] =cpu_to_be32 (cmd->data->blocks); + } + +if (cmd->opcode ==SD_IO_RW_EXTENDED ) { + arg &= ~(UHS2_DCMD_LM_TLEN_EXIST | +UHS2_DCMD_TLUM_BYTE_MODE | +UHS2_NATIVE_DCMD_DAM_IO ); + payload[1 ] =0 ; + plen =1 ; + } + }else { + plen =1 ; + } + + payload[0 ] =cpu_to_be32 (cmd->arg); + +sd_uhs2_cmd_assemble (cmd, uhs2_cmd, header, arg, payload, plen,NULL ,0 ); + +return 0 ; +} +EXPORT_SYMBOL_GPL (sd_uhs2_prepare_cmd); +static const struct mmc_bus_ops sd_uhs2_ops = { .remove = sd_uhs2_remove, .alive = sd_uhs2_alive,
@@ -251,18 +1055,33 @@ static int sd_uhs2_attach(struct mmc_host *host) goto remove_card;mmc_claim_host (host); + + host->ops->uhs2_host_operation (host,UHS2_POST_ATTACH_SD ); +return 0 ; remove_card: -mmc_remove_card (host->card); - host->card =NULL ; +sd_uhs2_remove (host->card);mmc_claim_host (host); -mmc_detach_bus (host); + err: +mmc_detach_bus (host);sd_uhs2_power_off (host); +if (host->uhs2_caps.flags &MMC_UHS2_INITIALIZED ) + host->uhs2_caps.flags &= ~MMC_UHS2_INITIALIZED ; + host->uhs2_caps.flags &= ~MMC_UHS2_SUPPORT ;return err; } +/** +* mmc_attach_sd_uhs2 - select UHS2 interface +* @host: MMC host +* +* Try to select UHS2 interface and initialize the bus for a given +* frequency, @freq. +* +* Return: 0 on success, non-zero error on failure +*/ int mmc_attach_sd_uhs2 (struct mmc_host *host) {int i, err =0 ;
@@ -273,6 +1092,8 @@ int mmc_attach_sd_uhs2(struct mmc_host *host)/* Turn off the legacy SD interface before trying with UHS-II. */ mmc_power_off (host); + host->uhs2_caps.flags |=MMC_UHS2_SUPPORT ; +/* * Start UHS-II initialization at 52MHz and possibly make a retry at * 26MHz according to the spec. It's required that the host driver
@@ -280,6 +1101,9 @@ int mmc_attach_sd_uhs2(struct mmc_host *host)*/ for (i =0 ; i <ARRAY_SIZE (sd_uhs2_freqs); i++) { host->f_init = sd_uhs2_freqs[i]; +pr_info ("%s: %s: trying to init UHS-II card at %u Hz\n" , +mmc_hostname (host), __func__, host->f_init); + err =sd_uhs2_attach (host);if (!err)break ;
Signature · 1 line
2.34.0
PATCH v2 7/7 mmc: core: Support UHS-II card access
In reply to Jason LaiFrom: Jason Lai <[email protected]>
Embed UHS-II access functionality into the MMC request processing flow.
--- drivers/mmc/core/core.c | 26 ++++++++++++++++++++++++-- 1 file changed, 24 insertions(+), 2 deletions(-)
drivers/mmc/core/core.c +24 -2
@@ -31,6 +31,7 @@#include <linux/mmc/mmc.h> #include <linux/mmc/sd.h> #include <linux/mmc/slot-gpio.h> +#include <linux/mmc/sd_uhs2.h> #define CREATE_TRACE_POINTS #include <trace/events/mmc.h>
@@ -42,6 +43,7 @@#include "host.h" #include "sdio_bus.h" #include "pwrseq.h" +#include "sd_uhs2.h" #include "mmc_ops.h" #include "sd_ops.h"
@@ -335,6 +337,8 @@ static int mmc_mrq_prep(struct mmc_host *host, struct mmc_request *mrq)int mmc_start_request (struct mmc_host *host,struct mmc_request *mrq) { +struct uhs2_command uhs2_cmd; +u32 payload[4 ];/* for maximum size */ int err;init_completion (&mrq->cmd_completion);
@@ -352,6 +356,13 @@ int mmc_start_request(struct mmc_host *host, struct mmc_request *mrq)if (err)return err; +if (host->uhs2_caps.flags &MMC_UHS2_SUPPORT && + host->uhs2_caps.flags &MMC_UHS2_INITIALIZED ) { + uhs2_cmd.payload = payload; + mrq->cmd->uhs2_cmd = &uhs2_cmd; +sd_uhs2_prepare_cmd (host, mrq); + } +led_trigger_event (host->led,LED_FULL );__mmc_start_request (host, mrq);
@@ -431,6 +442,8 @@ EXPORT_SYMBOL(mmc_wait_for_req_done);*/ int mmc_cqe_start_req (struct mmc_host *host,struct mmc_request *mrq) { +struct uhs2_command uhs2_cmd; +u32 payload[4 ];/* for maximum size */ int err;/*
@@ -451,6 +464,13 @@ int mmc_cqe_start_req(struct mmc_host *host, struct mmc_request *mrq)if (err) goto out_err; +if (host->uhs2_caps.flags &MMC_UHS2_SUPPORT && + host->uhs2_caps.flags &MMC_UHS2_INITIALIZED ) { + uhs2_cmd.payload = payload; + mrq->cmd->uhs2_cmd = &uhs2_cmd; +sd_uhs2_prepare_cmd (host, mrq); + } + err = host->cqe_ops->cqe_request (host, mrq);if (err) goto out_err;
@@ -899,8 +919,10 @@ static inline void mmc_set_ios(struct mmc_host *host)*/ void mmc_set_chip_select (struct mmc_host *host,int mode) { - host->ios.chip_select = mode; -mmc_set_ios (host); +if (!(host->uhs2_caps.flags &MMC_UHS2_INITIALIZED )) { + host->ios.chip_select = mode; +mmc_set_ios (host); + } }/*
Signature · 1 line
2.34.0
Quoted 16 lines · Jason Lai
Series [1] that has been posted by Ulf Hansson which provided some guidance and an overall structure.
Series [2] focused on UHS-II card control side to address Ulf's intention regarding to "modularising"
sd_uhs2.c.Series [3] is based on series [2] and adopt most of Ulf's comments.
This series is the successor version of post [3], which adopts Ulf's comments about series [3]:
1. Remove unnecessary debug print.
2. Rephrase description aboutuhs2_cmd_assemble()insd_uhs2.c
3. Place UHS-II variables in the appropriate structure.
4. Integrate 5 callback functions inhost->uhs2_host_operation().
Quoted 2 lines
Kind regards
Jason Lai
Hi Jason,
I have looked through the series, but I again find it a bit difficult to review, sorry. I couldn't apply the patches to my next branch (so I fixed that manually), the patches don't build and I get a lot of checkpatch errors/warnings.
I tried to help out and worked on fixing these issues and to improve the series. However in the end it turned out to be more work than expected and time I don't have at the moment.
To move forward, may I suggest rebasing the series on top of my latest next branch, run checkpatch and make sure it doesn't give errors/warnings, then of course you also need to make sure that each patch can be compiled. Then we can take it from there.
Kind regards
Uffe
Quoted 37 lines
[1]
https://patchwork.kernel.org/project/linux-mmc/list/?series=438509[2]
https://patchwork.kernel.org/project/linux-mmc/list/?series=539737[3]
https://patchwork.kernel.org/project/linux-mmc/list/?series=589827Jason Lai (3):
mmc: add UHS-II related definitions in headers
mmc: Implement content of UHS-II card initialization functions
mmc: core: Support UHS-II card accessUlf Hansson (4):
mmc: core: Cleanup printing of speed mode at card insertion
mmc: core: Prepare to support SD UHS-II cards
mmc: core: Announce successful insertion of an SD UHS-II card
mmc: core: Extend support for mmc regulators with a vqmmc2drivers/mmc/core/Makefile | 2 +- drivers/mmc/core/bus.c | 38 +- drivers/mmc/core/core.c | 43 +- drivers/mmc/core/core.h | 1 + drivers/mmc/core/host.h | 4 + drivers/mmc/core/regulator.c | 34 ++ drivers/mmc/core/sd_uhs2.c | 1113 ++++++++++++++++++++++++++++++++++ include/linux/mmc/card.h | 35 ++ include/linux/mmc/core.h | 1 + include/linux/mmc/host.h | 68 +++ 10 files changed, 1319 insertions(+), 20 deletions(-) create mode 100644 drivers/mmc/core/sd_uhs2.c--
2.34.0