phy: nop-phy: Enable reset-gpios support
PATCH v3 1/1 phy: nop-phy: Enable reset-gpios support
Some usb-nop-xceiv devices use a gpio to put them in and out of reset. Add a reset function to put them into that state. This is similar to how Linux handles the usb-nop-xceiv driver.
---
V3: Encapsulate the nop_phy_ops reference to nop_phy_reset
in an if-def so it doesn't appear when DM_GPIO is not enabled.
V2: Only use the GPIO functions when DM_GPIO is enabled
Add error handling so if the GPIO fails, it will shutdown the clocks and return with the error code.
Call nop_phy_reset() instead of repeating the same code.
drivers/phy/nop-phy.c +41 -2
@@ -10,17 +10,47 @@#include <dm/device.h> #include <dm/device_compat.h> #include <generic-phy.h> +#include <asm-generic/gpio.h> struct nop_phy_priv {struct clk_bulk bulk; +#if CONFIG_IS_ENABLED (DM_GPIO ) +struct gpio_desc reset_gpio; +#endif }; +#if CONFIG_IS_ENABLED (DM_GPIO ) +static int nop_phy_reset (struct phy *phy) +{ +struct nop_phy_priv *priv =dev_get_priv (phy->dev); + +/* Return if there is no gpio since it's optional */ +if (!dm_gpio_is_valid (&priv->reset_gpio)) +return 0 ; + +return dm_gpio_set_value (&priv->reset_gpio, false); +} +#endif +static int nop_phy_init (struct phy *phy) {struct nop_phy_priv *priv =dev_get_priv (phy->dev); +int ret =0 ; + +if (CONFIG_IS_ENABLED (CLK )) { + ret =clk_enable_bulk (&priv->bulk); +if (ret) +return ret; + } -if (CONFIG_IS_ENABLED (CLK )) -return clk_enable_bulk (&priv->bulk); +if (CONFIG_IS_ENABLED (DM_GPIO )) { + ret =nop_phy_reset (phy); +if (ret) { +if (CONFIG_IS_ENABLED (CLK )) +clk_disable_bulk (&priv->bulk); +return ret; + } + }return 0 ; }
@@ -38,6 +68,12 @@ static int nop_phy_probe(struct udevice *dev) } } + ret =gpio_request_by_name (dev,"reset-gpios" ,0 , + &priv->reset_gpio, +GPIOD_IS_OUT ); +if (ret != -ENOENT ) +return ret; +return 0 ; }
@@ -49,6 +85,9 @@ static const struct udevice_id nop_phy_ids[] = {static struct phy_ops nop_phy_ops = { .init = nop_phy_init, +#if CONFIG_IS_ENABLED(DM_GPIO) + .reset = nop_phy_reset, +#endif };U_BOOT_DRIVER (nop_phy) = {
Signature · 1 line
2.32.0
Quoted 11 lines · Adam Ford
Some usb-nop-xceiv devices use a gpio to put them in and out of reset. Add a reset function to put them into that state. This is similar to how Linux handles the usb-nop-xceiv driver.
Signed-off-by Adam Ford <[email protected]>---
V3: Encapsulate thenop_phy_opsreference tonop_phy_reset
in an if-def so it doesn't appear whenDM_GPIOis not enabled.
Quoted 4 lines
V2: Only use the GPIO functions when
DM_GPIOis enabled
Add error handling so if the GPIO fails, it will shutdown the clocks and return with the error code.
Callnop_phy_reset()instead of repeating the same code.
At the risk of sounding a bit too cranky, please build test v4 for k2e_evm as it's still failing to build due to these changes.
Signature · 1 line
Tom