Skip to contentSkip to conversation

arm64: dts: meson-sm1-odroid: use correct enable-gpio pin for tf-io regulator

PATCH Applied Lutz Koschorreck 2 participants 3 messages Jan 27, 2022 – Feb 4, 2022

Subsystems (2)
Device tree bindings Arm/Amlogic Meson SoC support
lore
Share & tools
lore

Lutz Koschorreck

author
#0 lore raw

PATCH v2 1/1 arm64: dts: meson-sm1-odroid: use correct enable-gpio pin for tf-io regulator

The interrupt pin of the external ethernet phy is used, instead of the enable-gpio pin of the tf-io regulator. The GPIOE_2 pin is located in the gpio_ao bank.

This causes phy interrupt problems at system startup.

[   76.645190] irq 36: nobody cared (try booting with the "irqpoll" option)
[   76.649617] CPU: 0 PID: 1416 Comm: irq/36-0.0:00 Not tainted 5.16.0 #2
[   76.649629] Hardware name: Hardkernel ODROID-HC4 (DT)
[   76.649635] Call trace:
[   76.649638]  dump_backtrace+0x0/0x1c8
[   76.649658]  show_stack+0x14/0x60
[   76.649667]  dump_stack_lvl+0x64/0x7c
[   76.649676]  dump_stack+0x14/0x2c
[   76.649683]  __report_bad_irq+0x38/0xe8
[   76.649695]  note_interrupt+0x220/0x3a0
[   76.649704]  handle_irq_event_percpu+0x58/0x88
[   76.649713]  handle_irq_event+0x44/0xd8
[   76.649721]  handle_fasteoi_irq+0xa8/0x130
[   76.649730]  generic_handle_domain_irq+0x38/0x58
[   76.649738]  gic_handle_irq+0x9c/0xb8
[   76.649747]  call_on_irq_stack+0x28/0x38
[   76.649755]  do_interrupt_handler+0x7c/0x80
[   76.649763]  el1_interrupt+0x34/0x80
[   76.649772]  el1h_64_irq_handler+0x14/0x20
[   76.649781]  el1h_64_irq+0x74/0x78
[   76.649788]  irq_finalize_oneshot.part.56+0x68/0xf8
[   76.649796]  irq_thread_fn+0x5c/0x98
[   76.649804]  irq_thread+0x13c/0x260
[   76.649812]  kthread+0x144/0x178
[   76.649822]  ret_from_fork+0x10/0x20
[   76.649830] handlers:
[   76.653170] [<0000000025a6cd31>] irq_default_primary_handler threaded [<0000000093580eb7>] phy_interrupt
[   76.661256] Disabling IRQ #36
Fixes 1f80a5cf74a6 ("arm64: dts: meson-sm1-odroid: add missing enable gpio and supply for tf_io regulator")
Signed-off-by Lutz Koschorreck <[email protected]>

only gpio bank

---
 arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi +1 -1
index 0bd1e98a0eef..ed7cd5f53046 100644
@@ -48,7 +48,7 @@ tf_io: gpio-regulator-tf_io {
 		regulator-max-microvolt = <3300000>;
 		vin-supply = <&vcc_5v>;
 
-		enable-gpio = <&gpio GPIOE_2 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		regulator-always-on;
Signature · 1 line
2.25.1
Reviewed-by on v2 1/1
#1 lore raw
Quoted 34 lines · Lutz Koschorreck

The interrupt pin of the external ethernet phy is used, instead of the enable-gpio pin of the tf-io regulator. The GPIOE_2 pin is located in the gpio_ao bank.

This causes phy interrupt problems at system startup.

[   76.645190] irq 36: nobody cared (try booting with the "irqpoll" option)
[   76.649617] CPU: 0 PID: 1416 Comm: irq/36-0.0:00 Not tainted 5.16.0 #2
[   76.649629] Hardware name: Hardkernel ODROID-HC4 (DT)
[   76.649635] Call trace:
[   76.649638]  dump_backtrace+0x0/0x1c8
[   76.649658]  show_stack+0x14/0x60
[   76.649667]  dump_stack_lvl+0x64/0x7c
[   76.649676]  dump_stack+0x14/0x2c
[   76.649683]  __report_bad_irq+0x38/0xe8
[   76.649695]  note_interrupt+0x220/0x3a0
[   76.649704]  handle_irq_event_percpu+0x58/0x88
[   76.649713]  handle_irq_event+0x44/0xd8
[   76.649721]  handle_fasteoi_irq+0xa8/0x130
[   76.649730]  generic_handle_domain_irq+0x38/0x58
[   76.649738]  gic_handle_irq+0x9c/0xb8
[   76.649747]  call_on_irq_stack+0x28/0x38
[   76.649755]  do_interrupt_handler+0x7c/0x80
[   76.649763]  el1_interrupt+0x34/0x80
[   76.649772]  el1h_64_irq_handler+0x14/0x20
[   76.649781]  el1h_64_irq+0x74/0x78
[   76.649788]  irq_finalize_oneshot.part.56+0x68/0xf8
[   76.649796]  irq_thread_fn+0x5c/0x98
[   76.649804]  irq_thread+0x13c/0x260
[   76.649812]  kthread+0x144/0x178
[   76.649822]  ret_from_fork+0x10/0x20
[   76.649830] handlers:
[   76.653170] [<0000000025a6cd31>] irq_default_primary_handler threaded [<0000000093580eb7>] phy_interrupt
[   76.661256] Disabling IRQ #36
Quoted 5 lines
Fixes 1f80a5cf74a6 ("arm64: dts: meson-sm1-odroid: add missing enable gpio and supply for tf_io regulator")
Signed-off-by Lutz Koschorreck <[email protected]>

only gpio bank

Spurious lines, will remove while applying

Quoted 10 lines
---
 arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi +0 -0
index 0bd1e98a0eef..ed7cd5f53046 100644

arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi tf_io: gpio-regulator-tf_io { · line 54

Quoted 8 lines
arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi +1 -1
@@ -48,7 +48,7 @@ tf_io: gpio-regulator-tf_io {
 		regulator-max-microvolt = <3300000>;
 		vin-supply = <&vcc_5v>;
 
-		enable-gpio = <&gpio GPIOE_2 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		regulator-always-on;
Reviewed-by Neil Armstrong <[email protected]>
Applied
#2 lore raw
In reply to Lutz Koschorreck

Hi,

Quoted 34 lines · Lutz Koschorreck

The interrupt pin of the external ethernet phy is used, instead of the enable-gpio pin of the tf-io regulator. The GPIOE_2 pin is located in the gpio_ao bank.

This causes phy interrupt problems at system startup.

[   76.645190] irq 36: nobody cared (try booting with the "irqpoll" option)
[   76.649617] CPU: 0 PID: 1416 Comm: irq/36-0.0:00 Not tainted 5.16.0 #2
[   76.649629] Hardware name: Hardkernel ODROID-HC4 (DT)
[   76.649635] Call trace:
[   76.649638]  dump_backtrace+0x0/0x1c8
[   76.649658]  show_stack+0x14/0x60
[   76.649667]  dump_stack_lvl+0x64/0x7c
[   76.649676]  dump_stack+0x14/0x2c
[   76.649683]  __report_bad_irq+0x38/0xe8
[   76.649695]  note_interrupt+0x220/0x3a0
[   76.649704]  handle_irq_event_percpu+0x58/0x88
[   76.649713]  handle_irq_event+0x44/0xd8
[   76.649721]  handle_fasteoi_irq+0xa8/0x130
[   76.649730]  generic_handle_domain_irq+0x38/0x58
[   76.649738]  gic_handle_irq+0x9c/0xb8
[   76.649747]  call_on_irq_stack+0x28/0x38
[   76.649755]  do_interrupt_handler+0x7c/0x80
[   76.649763]  el1_interrupt+0x34/0x80
[   76.649772]  el1h_64_irq_handler+0x14/0x20
[   76.649781]  el1h_64_irq+0x74/0x78
[   76.649788]  irq_finalize_oneshot.part.56+0x68/0xf8
[   76.649796]  irq_thread_fn+0x5c/0x98
[   76.649804]  irq_thread+0x13c/0x260
[   76.649812]  kthread+0x144/0x178
[   76.649822]  ret_from_fork+0x10/0x20
[   76.649830] handlers:
[   76.653170] [<0000000025a6cd31>] irq_default_primary_handler threaded [<0000000093580eb7>] phy_interrupt
[   76.661256] Disabling IRQ #36
Quoted 1 line

[...]

Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v5.17/fixes)

[1/1] arm64: dts: meson-sm1-odroid: use correct enable-gpio pin for tf-io regulator

      https://git.kernel.org/amlogic/c/323ca765bfe9d637fa774373baec0bc41e51fcfa
Signature · 1 line
Neil