iio: temperature: ltc2983: Don't hard code defined constants in messages
Subsystems (2)
PATCH 1/2 iio: temperature: ltc2983: Don't hard code defined constants in messages
In a couple of messages the constants, which have their definitions, are hard coded into the message text. Unhardcode them.
--- drivers/iio/temperature/ltc2983.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/iio/temperature/ltc2983.c +4 -4
@@ -409,8 +409,8 @@ static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( new_custom->size = n_entries * n_size;/* check Steinhart size */ if (is_steinhart && new_custom->size !=LTC2983_CUSTOM_STEINHART_SIZE ) { -dev_err (dev,"Steinhart sensors size(%zu) must be 24" , - new_custom->size); +dev_err (dev,"Steinhart sensors size(%zu) must be %d" , new_custom->size, +LTC2983_CUSTOM_STEINHART_SIZE );return ERR_PTR (-EINVAL ); }/* Check space on the table. */
@@ -1299,8 +1299,8 @@ static int ltc2983_parse_dt(struct ltc2983_data *st)if (sensor.chan <LTC2983_MIN_CHANNELS_NR || sensor.chan >LTC2983_MAX_CHANNELS_NR ) { ret = -EINVAL ; -dev_err (dev, -"chan:%d must be from 1 to 20\n" , sensor.chan); +dev_err (dev,"chan:%d must be from %d to %d\n" , sensor.chan, +LTC2983_MIN_CHANNELS_NR ,LTC2983_MAX_CHANNELS_NR ); goto put_child; }else if (channel_avail_mask &BIT (sensor.chan)) { ret = -EINVAL ;
Signature · 1 line
2.34.1
PATCH 2/2 iio: temperature: ltc2983: Make use of device properties
Convert the module to be property provider agnostic and allow it to be used on non-OF platforms.
--- drivers/iio/temperature/ltc2983.c | 211 +++++++++++++++--------------- 1 file changed, 105 insertions(+), 106 deletions(-)
drivers/iio/temperature/ltc2983.c +105 -106
@@ -12,11 +12,15 @@#include <linux/iio/iio.h> #include <linux/interrupt.h> #include <linux/list.h> +#include <linux/mod_devicetable.h> #include <linux/module.h> -#include <linux/of_gpio.h> +#include <linux/property.h> #include <linux/regmap.h> #include <linux/spi/spi.h> +#include <asm/byteorder.h> +#include <asm/unaligned.h> +/* register map */ #define LTC2983_STATUS_REG 0x0000#define LTC2983_TEMP_RES_START_REG 0x0010
@@ -219,7 +223,7 @@ struct ltc2983_sensor {struct ltc2983_custom_sensor {/* raw table sensor data */ -u8 *table; +void *table;size_t size;/* address offset */ s8 offset;
@@ -377,25 +381,25 @@ static int __ltc2983_chan_custom_sensor_assign(struct ltc2983_data *st,return regmap_bulk_write (st->regmap, reg, custom->table, custom->size); } -static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new ( -struct ltc2983_data *st, -const struct device_node *np, -const char *propname, -const bool is_steinhart, -const u32 resolution, -const bool has_signed) +static struct ltc2983_custom_sensor * +__ltc2983_custom_sensor_new (struct ltc2983_data *st,const struct fwnode_handle *fn, +const char *propname,const bool is_steinhart, +const u32 resolution,const bool has_signed) {struct ltc2983_custom_sensor *new_custom; -u8 index, n_entries, tbl =0 ;struct device *dev = &st->spi->dev;/* * For custom steinhart, the full u32 is taken. For all the others * the MSB is discarded. */ const u8 n_size = is_steinhart ?4 :3 ; -const u8 e_size = is_steinhart ?sizeof (u32) :sizeof (u64); +u8 index, n_entries; +int ret; - n_entries =of_property_count_elems_of_size (np, propname, e_size); +if (is_steinhart) + n_entries =fwnode_property_count_u32 (fn, propname); +else + n_entries =fwnode_property_count_u64 (fn, propname);/* n_entries must be an even number */ if (!n_entries || (n_entries %2 ) !=0 ) {dev_err (dev,"Number of entries either 0 or not even\n" );
@@ -415,29 +419,39 @@ static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( }/* Check space on the table. */ if (st->custom_table_size + new_custom->size > - (LTC2983_CUST_SENS_TBL_END_REG - -LTC2983_CUST_SENS_TBL_START_REG ) +1 ) { + (LTC2983_CUST_SENS_TBL_END_REG -LTC2983_CUST_SENS_TBL_START_REG ) +1 ) {dev_err (dev,"No space left(%d) for new custom sensor(%zu)" , st->custom_table_size, new_custom->size);return ERR_PTR (-EINVAL ); }/* allocate the table */ - new_custom->table =devm_kzalloc (dev, new_custom->size,GFP_KERNEL ); +if (is_steinhart) + new_custom->table =devm_kcalloc (dev, n_entries,sizeof (u32),GFP_KERNEL ); +else + new_custom->table =devm_kcalloc (dev, n_entries,sizeof (u64),GFP_KERNEL );if (!new_custom->table)return ERR_PTR (-ENOMEM ); -for (index =0 ; index < n_entries; index++) { -u64 temp =0 , j; -/* -* Steinhart sensors are configured with raw values in the -* devicetree. For the other sensors we must convert the -* value to raw. The odd index's correspond to temperarures -* and always have 1/1024 of resolution. Temperatures also -* come in kelvin, so signed values is not possible -*/ -if (!is_steinhart) { -of_property_read_u64_index (np, propname, index, &temp); +if (is_steinhart) + ret =fwnode_property_read_u32_array (fn, propname, new_custom->table, n_entries); +else + ret =fwnode_property_read_u64_array (fn, propname, new_custom->table, n_entries); +if (ret <0 ) +return ERR_PTR (ret); + +/* +* Steinhart sensors are configured with raw values in the device tree. +* For the other sensors we must convert the value to raw. The odd +* index's correspond to temperatures and always have 1/1024 of +* resolution. Temperatures also come in Kelvin, so signed values is +* not possible. +*/ +if (is_steinhart) { +cpu_to_be32_array (new_custom->table, new_custom->table, n_entries); + }else { +for (index =0 ; index < n_entries; index++) { +u64 temp = ((u64 *)new_custom->table)[index];if ((index %2 ) !=0 ) temp =__convert_to_raw (temp,1024 );
@@ -445,16 +459,9 @@ static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( temp =__convert_to_raw_sign (temp, resolution); else temp =__convert_to_raw (temp, resolution); - }else { -u32 t32; -of_property_read_u32_index (np, propname, index, &t32); - temp = t32; +put_unaligned_be24 (temp, new_custom->table + index *3 ); } - -for (j =0 ; j < n_size; j++) - new_custom->table[tbl++] = - temp >> (8 * (n_size - j -1 )); } new_custom->is_steinhart = is_steinhart;
@@ -597,13 +604,12 @@ static int ltc2983_adc_assign_chan(struct ltc2983_data *st,return __ltc2983_chan_assign_common (st, sensor, chan_val); } -static struct ltc2983_sensor *ltc2983_thermocouple_new ( -const struct device_node *child, -struct ltc2983_data *st, -const struct ltc2983_sensor *sensor) +static struct ltc2983_sensor * +ltc2983_thermocouple_new (const struct fwnode_handle *child,struct ltc2983_data *st, +const struct ltc2983_sensor *sensor) {struct ltc2983_thermocouple *thermo; -struct device_node *phandle; +struct fwnode_handle *ref;u32 oc_current;int ret;
@@ -611,11 +617,10 @@ static struct ltc2983_sensor *ltc2983_thermocouple_new(if (!thermo)return ERR_PTR (-ENOMEM ); -if (of_property_read_bool (child,"adi,single-ended" )) +if (fwnode_property_read_bool (child,"adi,single-ended" )) thermo->sensor_config =LTC2983_THERMOCOUPLE_SGL (1 ); - ret =of_property_read_u32 (child,"adi,sensor-oc-current-microamp" , - &oc_current); + ret =fwnode_property_read_u32 (child,"adi,sensor-oc-current-microamp" , &oc_current);if (!ret) {switch (oc_current) {case 10 :
@@ -651,19 +656,18 @@ static struct ltc2983_sensor *ltc2983_thermocouple_new(return ERR_PTR (-EINVAL ); } - phandle =of_parse_phandle (child,"adi,cold-junction-handle" ,0 ); -if (phandle) { + ref =fwnode_find_reference (child,"adi,cold-junction-handle" ,0 ); +if (ref) {int ret; - ret =of_property_read_u32 (phandle,"reg" , - &thermo->cold_junction_chan); + ret =fwnode_property_read_u32 (ref,"reg" , &thermo->cold_junction_chan);if (ret) {/* * This would be catched later but we can just return * the error right away. */ dev_err (&st->spi->dev,"Property reg must be given\n" ); -of_node_put (phandle); +fwnode_handle_put (ref);return ERR_PTR (-EINVAL ); } }
@@ -676,7 +680,7 @@ static struct ltc2983_sensor *ltc2983_thermocouple_new( propname, false, 16384, true);if (IS_ERR (thermo->custom)) { -of_node_put (phandle); +fwnode_handle_put (ref);return ERR_CAST (thermo->custom); } }
@@ -685,37 +689,37 @@ static struct ltc2983_sensor *ltc2983_thermocouple_new( thermo->sensor.fault_handler = ltc2983_thermocouple_fault_handler; thermo->sensor.assign_chan = ltc2983_thermocouple_assign_chan; -of_node_put (phandle); +fwnode_handle_put (ref);return &thermo->sensor; } -static struct ltc2983_sensor *ltc2983_rtd_new (const struct device_node *child, -struct ltc2983_data *st, -const struct ltc2983_sensor *sensor) +static struct ltc2983_sensor * +ltc2983_rtd_new (const struct fwnode_handle *child,struct ltc2983_data *st, +const struct ltc2983_sensor *sensor) {struct ltc2983_rtd *rtd;int ret =0 ;struct device *dev = &st->spi->dev; -struct device_node *phandle; +struct fwnode_handle *ref;u32 excitation_current =0 , n_wires =0 ; rtd =devm_kzalloc (dev,sizeof (*rtd),GFP_KERNEL );if (!rtd)return ERR_PTR (-ENOMEM ); - phandle =of_parse_phandle (child,"adi,rsense-handle" ,0 ); -if (!phandle) { + ref =fwnode_find_reference (child,"adi,rsense-handle" ,0 ); +if (!ref) {dev_err (dev,"Property adi,rsense-handle missing or invalid" );return ERR_PTR (-EINVAL ); } - ret =of_property_read_u32 (phandle,"reg" , &rtd->r_sense_chan); + ret =fwnode_property_read_u32 (ref,"reg" , &rtd->r_sense_chan);if (ret) {dev_err (dev,"Property reg must be given\n" ); goto fail; } - ret =of_property_read_u32 (child,"adi,number-of-wires" , &n_wires); + ret =fwnode_property_read_u32 (child,"adi,number-of-wires" , &n_wires);if (!ret) {switch (n_wires) {case 2 :
@@ -738,9 +742,9 @@ static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child, } } -if (of_property_read_bool (child,"adi,rsense-share" )) { +if (fwnode_property_read_bool (child,"adi,rsense-share" )) {/* Current rotation is only available with rsense sharing */ -if (of_property_read_bool (child,"adi,current-rotate" )) { +if (fwnode_property_read_bool (child,"adi,current-rotate" )) {if (n_wires ==2 || n_wires ==3 ) {dev_err (dev,"Rotation not allowed for 2/3 Wire RTDs" );
@@ -803,7 +807,7 @@ static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child,"adi,custom-rtd" , false, 2048, false);if (IS_ERR (rtd->custom)) { -of_node_put (phandle); +fwnode_handle_put (ref);return ERR_CAST (rtd->custom); } }
@@ -812,8 +816,8 @@ static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child, rtd->sensor.fault_handler = ltc2983_common_fault_handler; rtd->sensor.assign_chan = ltc2983_rtd_assign_chan; - ret =of_property_read_u32 (child,"adi,excitation-current-microamp" , - &excitation_current); + ret =fwnode_property_read_u32 (child,"adi,excitation-current-microamp" , + &excitation_current);if (ret) {/* default to 5uA */ rtd->excitation_current =1 ;
@@ -852,23 +856,22 @@ static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child, } } -of_property_read_u32 (child,"adi,rtd-curve" , &rtd->rtd_curve); +fwnode_property_read_u32 (child,"adi,rtd-curve" , &rtd->rtd_curve); -of_node_put (phandle); +fwnode_handle_put (ref);return &rtd->sensor; fail: -of_node_put (phandle); +fwnode_handle_put (ref);return ERR_PTR (ret); } -static struct ltc2983_sensor *ltc2983_thermistor_new ( -const struct device_node *child, -struct ltc2983_data *st, -const struct ltc2983_sensor *sensor) +static struct ltc2983_sensor * +ltc2983_thermistor_new (const struct fwnode_handle *child,struct ltc2983_data *st, +const struct ltc2983_sensor *sensor) {struct ltc2983_thermistor *thermistor;struct device *dev = &st->spi->dev; -struct device_node *phandle; +struct fwnode_handle *ref;u32 excitation_current =0 ;int ret =0 ;
@@ -876,23 +879,23 @@ static struct ltc2983_sensor *ltc2983_thermistor_new(if (!thermistor)return ERR_PTR (-ENOMEM ); - phandle =of_parse_phandle (child,"adi,rsense-handle" ,0 ); -if (!phandle) { + ref =fwnode_find_reference (child,"adi,rsense-handle" ,0 ); +if (!ref) {dev_err (dev,"Property adi,rsense-handle missing or invalid" );return ERR_PTR (-EINVAL ); } - ret =of_property_read_u32 (phandle,"reg" , &thermistor->r_sense_chan); + ret =fwnode_property_read_u32 (ref,"reg" , &thermistor->r_sense_chan);if (ret) {dev_err (dev,"rsense channel must be configured...\n" ); goto fail; } -if (of_property_read_bool (child,"adi,single-ended" )) { +if (fwnode_property_read_bool (child,"adi,single-ended" )) { thermistor->sensor_config =LTC2983_THERMISTOR_SGL (1 ); - }else if (of_property_read_bool (child,"adi,rsense-share" )) { + }else if (fwnode_property_read_bool (child,"adi,rsense-share" )) {/* rotation is only possible if sharing rsense */ -if (of_property_read_bool (child,"adi,current-rotate" )) +if (fwnode_property_read_bool (child,"adi,current-rotate" )) thermistor->sensor_config =LTC2983_THERMISTOR_C_ROTATE (1 );else
@@ -926,7 +929,7 @@ static struct ltc2983_sensor *ltc2983_thermistor_new( steinhart, 64, false);if (IS_ERR (thermistor->custom)) { -of_node_put (phandle); +fwnode_handle_put (ref);return ERR_CAST (thermistor->custom); } }
@@ -934,8 +937,8 @@ static struct ltc2983_sensor *ltc2983_thermistor_new( thermistor->sensor.fault_handler = ltc2983_common_fault_handler; thermistor->sensor.assign_chan = ltc2983_thermistor_assign_chan; - ret =of_property_read_u32 (child,"adi,excitation-current-nanoamp" , - &excitation_current); + ret =fwnode_property_read_u32 (child,"adi,excitation-current-nanoamp" , + &excitation_current);if (ret) {/* Auto range is not allowed for custom sensors */ if (sensor->type >=LTC2983_SENSOR_THERMISTOR_STEINHART )
@@ -999,17 +1002,16 @@ static struct ltc2983_sensor *ltc2983_thermistor_new( } } -of_node_put (phandle); +fwnode_handle_put (ref);return &thermistor->sensor; fail: -of_node_put (phandle); +fwnode_handle_put (ref);return ERR_PTR (ret); } -static struct ltc2983_sensor *ltc2983_diode_new ( -const struct device_node *child, -const struct ltc2983_data *st, -const struct ltc2983_sensor *sensor) +static struct ltc2983_sensor * +ltc2983_diode_new (const struct fwnode_handle *child,const struct ltc2983_data *st, +const struct ltc2983_sensor *sensor) {struct ltc2983_diode *diode;u32 temp =0 , excitation_current =0 ;
@@ -1019,13 +1021,13 @@ static struct ltc2983_sensor *ltc2983_diode_new(if (!diode)return ERR_PTR (-ENOMEM ); -if (of_property_read_bool (child,"adi,single-ended" )) +if (fwnode_property_read_bool (child,"adi,single-ended" )) diode->sensor_config =LTC2983_DIODE_SGL (1 ); -if (of_property_read_bool (child,"adi,three-conversion-cycles" )) +if (fwnode_property_read_bool (child,"adi,three-conversion-cycles" )) diode->sensor_config |=LTC2983_DIODE_3_CONV_CYCLE (1 ); -if (of_property_read_bool (child,"adi,average-on" )) +if (fwnode_property_read_bool (child,"adi,average-on" )) diode->sensor_config |=LTC2983_DIODE_AVERAGE_ON (1 );/* validate channel index */
@@ -1040,8 +1042,8 @@ static struct ltc2983_sensor *ltc2983_diode_new( diode->sensor.fault_handler = ltc2983_common_fault_handler; diode->sensor.assign_chan = ltc2983_diode_assign_chan; - ret =of_property_read_u32 (child,"adi,excitation-current-microamp" , - &excitation_current); + ret =fwnode_property_read_u32 (child,"adi,excitation-current-microamp" , + &excitation_current);if (!ret) {switch (excitation_current) {case 10 :
@@ -1064,7 +1066,7 @@ static struct ltc2983_sensor *ltc2983_diode_new( } } -of_property_read_u32 (child,"adi,ideal-factor-value" , &temp); +fwnode_property_read_u32 (child,"adi,ideal-factor-value" , &temp);/* 2^20 resolution */ diode->ideal_factor_value =__convert_to_raw (temp,1048576 );
@@ -1072,7 +1074,7 @@ static struct ltc2983_sensor *ltc2983_diode_new(return &diode->sensor; } -static struct ltc2983_sensor *ltc2983_r_sense_new (struct device_node *child, +static struct ltc2983_sensor *ltc2983_r_sense_new (struct fwnode_handle *child,struct ltc2983_data *st,const struct ltc2983_sensor *sensor) {
@@ -1091,7 +1093,7 @@ static struct ltc2983_sensor *ltc2983_r_sense_new(struct device_node *child,return ERR_PTR (-EINVAL ); } - ret =of_property_read_u32 (child,"adi,rsense-val-milli-ohms" , &temp); + ret =fwnode_property_read_u32 (child,"adi,rsense-val-milli-ohms" , &temp);if (ret) {dev_err (&st->spi->dev,"Property adi,rsense-val-milli-ohms missing\n" );return ERR_PTR (-EINVAL );
@@ -1110,7 +1112,7 @@ static struct ltc2983_sensor *ltc2983_r_sense_new(struct device_node *child,return &rsense->sensor; } -static struct ltc2983_sensor *ltc2983_adc_new (struct device_node *child, +static struct ltc2983_sensor *ltc2983_adc_new (struct fwnode_handle *child,struct ltc2983_data *st,const struct ltc2983_sensor *sensor) {
@@ -1120,7 +1122,7 @@ static struct ltc2983_sensor *ltc2983_adc_new(struct device_node *child,if (!adc)return ERR_PTR (-ENOMEM ); -if (of_property_read_bool (child,"adi,single-ended" )) +if (fwnode_property_read_bool (child,"adi,single-ended" )) adc->single_ended = true; if (!adc->single_ended &&
@@ -1264,17 +1266,15 @@ static irqreturn_t ltc2983_irq_handler(int irq, void *data)static int ltc2983_parse_dt (struct ltc2983_data *st) { -struct device_node *child;struct device *dev = &st->spi->dev; +struct fwnode_handle *child;int ret =0 , chan =0 , channel_avail_mask =0 ; -of_property_read_u32 (dev->of_node,"adi,mux-delay-config-us" , - &st->mux_delay_config); +device_property_read_u32 (dev,"adi,mux-delay-config-us" , &st->mux_delay_config); -of_property_read_u32 (dev->of_node,"adi,filter-notch-freq" , - &st->filter_notch_freq); +device_property_read_u32 (dev,"adi,filter-notch-freq" , &st->filter_notch_freq); - st->num_channels =of_get_available_child_count (dev->of_node); + st->num_channels =device_get_child_node_count (dev);if (!st->num_channels) {dev_err (&st->spi->dev,"At least one channel must be given!" );return -EINVAL ;
@@ -1286,10 +1286,10 @@ static int ltc2983_parse_dt(struct ltc2983_data *st)return -ENOMEM ; st->iio_channels = st->num_channels; -for_each_available_child_of_node (dev->of_node, child) { +device_for_each_child_node (dev, child) {struct ltc2983_sensor sensor; - ret =of_property_read_u32 (child,"reg" , &sensor.chan); + ret =fwnode_property_read_u32 (child,"reg" , &sensor.chan);if (ret) {dev_err (dev,"reg property must given for child nodes\n" ); goto put_child;
@@ -1308,8 +1308,7 @@ static int ltc2983_parse_dt(struct ltc2983_data *st) goto put_child; } - ret =of_property_read_u32 (child,"adi,sensor-type" , - &sensor.type); + ret =fwnode_property_read_u32 (child,"adi,sensor-type" , &sensor.type);if (ret) {dev_err (dev,"adi,sensor-type property must given for child nodes\n" );
@@ -1363,7 +1362,7 @@ static int ltc2983_parse_dt(struct ltc2983_data *st)return 0 ; put_child: -of_node_put (child); +fwnode_handle_put (child);return ret; }
Signature · 1 line
2.34.1
Jonathan Cameron
maintainerRe: [PATCH v1 2/2] iio: temperature: ltc2983: Make use of device properties
Quoted 2 lines · On Thu, 3 Feb 2022 13:45:06 +0200 Andy Shevchenko…
Convert the module to be property provider agnostic and allow it to be used on non-OF platforms.
This description needs expansion as it's not a straight forward conversion.
Also, complex enough that I definitely want more eyes and preferably some testing.
Thanks,
Jonathan
Quoted 14 lines
Signed-off-by Andy Shevchenko <[email protected]>--- drivers/iio/temperature/ltc2983.c | 211 +++++++++++++++--------------- 1 file changed, 105 insertions(+), 106 deletions(-)drivers/iio/temperature/ltc2983.c +0
-0@@ -12,11 +12,15 @@#include <linux/iio/iio.h> #include <linux/interrupt.h> #include <linux/list.h>
drivers/iio/temperature/ltc2983.c line 23
Quoted 10 lines
drivers/iio/temperature/ltc2983.c +5
-1+#include <linux/mod_devicetable.h> #include <linux/module.h> -#include <linux/of_gpio.h> +#include <linux/property.h> #include <linux/regmap.h> #include <linux/spi/spi.h> +#include <asm/byteorder.h> +#include <asm/unaligned.h> +
This may well be a valid addition but it's not called out in the patch description.
Quoted 49 lines
drivers/iio/temperature/ltc2983.c +11
-11/* register map */ #define LTC2983_STATUS_REG 0x0000#define LTC2983_TEMP_RES_START_REG 0x0010@@ -219,7 +223,7 @@ struct ltc2983_sensor {struct ltc2983_custom_sensor {/* raw table sensor data */ -u8 *table; +void *table;size_t size;/* address offset */ s8 offset;@@ -377,25 +381,25 @@ static int __ltc2983_chan_custom_sensor_assign(struct ltc2983_data *st,return regmap_bulk_write (st->regmap, reg, custom->table, custom->size); } -static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new ( -struct ltc2983_data *st, -const struct device_node *np, -const char *propname, -const bool is_steinhart, -const u32 resolution, -const bool has_signed) +static struct ltc2983_custom_sensor * +__ltc2983_custom_sensor_new (struct ltc2983_data *st,const struct fwnode_handle *fn, +const char *propname,const bool is_steinhart, +const u32 resolution,const bool has_signed) {struct ltc2983_custom_sensor *new_custom; -u8 index, n_entries, tbl =0 ;struct device *dev = &st->spi->dev;/* * For custom steinhart, the full u32 is taken. For all the others * the MSB is discarded. */ const u8 n_size = is_steinhart ?4 :3 ; -const u8 e_size = is_steinhart ?sizeof (u32) :sizeof (u64); +u8 index, n_entries; +int ret; - n_entries =of_property_count_elems_of_size (np, propname, e_size); +if (is_steinhart) + n_entries =fwnode_property_count_u32 (fn, propname); +else + n_entries =fwnode_property_count_u64 (fn, propname);/* n_entries must be an even number */ if (!n_entries || (n_entries %2 ) !=0 ) {dev_err (dev,"Number of entries either 0 or not even\n" );
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( · line 422
Quoted 6 lines
drivers/iio/temperature/ltc2983.c +1
-2@@ -415,29 +419,39 @@ static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( }/* Check space on the table. */ if (st->custom_table_size + new_custom->size > - (LTC2983_CUST_SENS_TBL_END_REG - -LTC2983_CUST_SENS_TBL_START_REG ) +1 ) { + (LTC2983_CUST_SENS_TBL_END_REG -LTC2983_CUST_SENS_TBL_START_REG ) +1 ) {
Shouldn't really be in this patch. Or at very least call out that there is whitespace cleanup in the patch description.
Quoted 30 lines
drivers/iio/temperature/ltc2983.c +9
-12dev_err (dev,"No space left(%d) for new custom sensor(%zu)" , st->custom_table_size, new_custom->size);return ERR_PTR (-EINVAL ); }/* allocate the table */ - new_custom->table =devm_kzalloc (dev, new_custom->size,GFP_KERNEL ); +if (is_steinhart) + new_custom->table =devm_kcalloc (dev, n_entries,sizeof (u32),GFP_KERNEL ); +else + new_custom->table =devm_kcalloc (dev, n_entries,sizeof (u64),GFP_KERNEL );if (!new_custom->table)return ERR_PTR (-ENOMEM ); -for (index =0 ; index < n_entries; index++) { -u64 temp =0 , j; -/* -* Steinhart sensors are configured with raw values in the -* devicetree. For the other sensors we must convert the -* value to raw. The odd index's correspond to temperarures -* and always have 1/1024 of resolution. Temperatures also -* come in kelvin, so signed values is not possible -*/ -if (!is_steinhart) { -of_property_read_u64_index (np, propname, index, &temp); +if (is_steinhart) + ret =fwnode_property_read_u32_array (fn, propname, new_custom->table, n_entries); +else + ret =fwnode_property_read_u64_array (fn, propname, new_custom->table, n_entries); +if (ret <0 )
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( · line 450
Quoted 10 lines
drivers/iio/temperature/ltc2983.c +10
-0+return ERR_PTR (ret); + +/* +* Steinhart sensors are configured with raw values in the device tree. +* For the other sensors we must convert the value to raw. The odd +* index's correspond to temperatures and always have 1/1024 of +* resolution. Temperatures also come in Kelvin, so signed values is +* not possible. +*/ +if (is_steinhart) {
Perhaps would be cleaner to combine this if else with the one above at the cost of duplicating the if (ret < 0) check.
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( · line 451
Quoted 1 line
drivers/iio/temperature/ltc2983.c +1
-0+cpu_to_be32_array (new_custom->table, new_custom->table, n_entries);
I completely failed to register the hand coded big endian conversion. Nice tidy up. However, definitely something to call out in the patch description.
Quoted 28 lines
drivers/iio/temperature/ltc2983.c +4
-8+ }else { +for (index =0 ; index < n_entries; index++) { +u64 temp = ((u64 *)new_custom->table)[index];if ((index %2 ) !=0 ) temp =__convert_to_raw (temp,1024 );@@ -445,16 +459,9 @@ static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( temp =__convert_to_raw_sign (temp, resolution); else temp =__convert_to_raw (temp, resolution); - }else { -u32 t32; -of_property_read_u32_index (np, propname, index, &t32); - temp = t32; +put_unaligned_be24 (temp, new_custom->table + index *3 ); } - -for (j =0 ; j < n_size; j++) - new_custom->table[tbl++] = - temp >> (8 * (n_size - j -1 )); } new_custom->is_steinhart = is_steinhart;@@ -597,13 +604,12 @@ static int ltc2983_adc_assign_chan(struct ltc2983_data *st,return __ltc2983_chan_assign_common (st, sensor, chan_val); }
...
Quoted 51 lines
drivers/iio/temperature/ltc2983.c +10
-10-static struct ltc2983_sensor *ltc2983_rtd_new (const struct device_node *child, -struct ltc2983_data *st, -const struct ltc2983_sensor *sensor) +static struct ltc2983_sensor * +ltc2983_rtd_new (const struct fwnode_handle *child,struct ltc2983_data *st, +const struct ltc2983_sensor *sensor) {struct ltc2983_rtd *rtd;int ret =0 ;struct device *dev = &st->spi->dev; -struct device_node *phandle; +struct fwnode_handle *ref;u32 excitation_current =0 , n_wires =0 ; rtd =devm_kzalloc (dev,sizeof (*rtd),GFP_KERNEL );if (!rtd)return ERR_PTR (-ENOMEM ); - phandle =of_parse_phandle (child,"adi,rsense-handle" ,0 ); -if (!phandle) { + ref =fwnode_find_reference (child,"adi,rsense-handle" ,0 ); +if (!ref) {dev_err (dev,"Property adi,rsense-handle missing or invalid" );return ERR_PTR (-EINVAL ); } - ret =of_property_read_u32 (phandle,"reg" , &rtd->r_sense_chan); + ret =fwnode_property_read_u32 (ref,"reg" , &rtd->r_sense_chan);if (ret) {dev_err (dev,"Property reg must be given\n" ); goto fail; } - ret =of_property_read_u32 (child,"adi,number-of-wires" , &n_wires); + ret =fwnode_property_read_u32 (child,"adi,number-of-wires" , &n_wires);if (!ret) {switch (n_wires) {case 2 :@@ -738,9 +742,9 @@ static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child, } } -if (of_property_read_bool (child,"adi,rsense-share" )) { +if (fwnode_property_read_bool (child,"adi,rsense-share" )) {/* Current rotation is only available with rsense sharing */ -if (of_property_read_bool (child,"adi,current-rotate" )) { +if (fwnode_property_read_bool (child,"adi,current-rotate" )) {if (n_wires ==2 || n_wires ==3 ) {dev_err (dev,"Rotation not allowed for 2/3 Wire RTDs" );
drivers/iio/temperature/ltc2983.c static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child, · line 810
Quoted 5 lines
drivers/iio/temperature/ltc2983.c +1
-1@@ -803,7 +807,7 @@ static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child,"adi,custom-rtd" , false, 2048, false);if (IS_ERR (rtd->custom)) { -of_node_put (phandle); +fwnode_handle_put (ref);
I guess there was a bunch of cut and paste in this driver ;) Same question as below on whether we can just use a goto here to share the put in the fail path.
Quoted 76 lines
drivers/iio/temperature/ltc2983.c +15
-16return ERR_CAST (rtd->custom); } }@@ -812,8 +816,8 @@ static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child, rtd->sensor.fault_handler = ltc2983_common_fault_handler; rtd->sensor.assign_chan = ltc2983_rtd_assign_chan; - ret =of_property_read_u32 (child,"adi,excitation-current-microamp" , - &excitation_current); + ret =fwnode_property_read_u32 (child,"adi,excitation-current-microamp" , + &excitation_current);if (ret) {/* default to 5uA */ rtd->excitation_current =1 ;@@ -852,23 +856,22 @@ static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child, } } -of_property_read_u32 (child,"adi,rtd-curve" , &rtd->rtd_curve); +fwnode_property_read_u32 (child,"adi,rtd-curve" , &rtd->rtd_curve); -of_node_put (phandle); +fwnode_handle_put (ref);return &rtd->sensor; fail: -of_node_put (phandle); +fwnode_handle_put (ref);return ERR_PTR (ret); } -static struct ltc2983_sensor *ltc2983_thermistor_new ( -const struct device_node *child, -struct ltc2983_data *st, -const struct ltc2983_sensor *sensor) +static struct ltc2983_sensor * +ltc2983_thermistor_new (const struct fwnode_handle *child,struct ltc2983_data *st, +const struct ltc2983_sensor *sensor) {struct ltc2983_thermistor *thermistor;struct device *dev = &st->spi->dev; -struct device_node *phandle; +struct fwnode_handle *ref;u32 excitation_current =0 ;int ret =0 ;@@ -876,23 +879,23 @@ static struct ltc2983_sensor *ltc2983_thermistor_new(if (!thermistor)return ERR_PTR (-ENOMEM ); - phandle =of_parse_phandle (child,"adi,rsense-handle" ,0 ); -if (!phandle) { + ref =fwnode_find_reference (child,"adi,rsense-handle" ,0 ); +if (!ref) {dev_err (dev,"Property adi,rsense-handle missing or invalid" );return ERR_PTR (-EINVAL ); } - ret =of_property_read_u32 (phandle,"reg" , &thermistor->r_sense_chan); + ret =fwnode_property_read_u32 (ref,"reg" , &thermistor->r_sense_chan);if (ret) {dev_err (dev,"rsense channel must be configured...\n" ); goto fail; } -if (of_property_read_bool (child,"adi,single-ended" )) { +if (fwnode_property_read_bool (child,"adi,single-ended" )) { thermistor->sensor_config =LTC2983_THERMISTOR_SGL (1 ); - }else if (of_property_read_bool (child,"adi,rsense-share" )) { + }else if (fwnode_property_read_bool (child,"adi,rsense-share" )) {/* rotation is only possible if sharing rsense */ -if (of_property_read_bool (child,"adi,current-rotate" )) +if (fwnode_property_read_bool (child,"adi,current-rotate" )) thermistor->sensor_config =LTC2983_THERMISTOR_C_ROTATE (1 );else
drivers/iio/temperature/ltc2983.c static struct ltc2983_sensor *ltc2983_thermistor_new( · line 933
Quoted 6 lines
drivers/iio/temperature/ltc2983.c +1
-1@@ -926,7 +929,7 @@ static struct ltc2983_sensor *ltc2983_thermistor_new( steinhart, 64, false);if (IS_ERR (thermistor->custom)) { -of_node_put (phandle); +fwnode_handle_put (ref);return ERR_CAST (thermistor->custom);
Obviously not due to this patch, but this is odd. Why have one error path that doesn't use the goto faill;?
If you could tidy that up and add a note on it to the patch description that would be great.
Quoted 26 lines
drivers/iio/temperature/ltc2983.c +4
-4} }@@ -934,8 +937,8 @@ static struct ltc2983_sensor *ltc2983_thermistor_new( thermistor->sensor.fault_handler = ltc2983_common_fault_handler; thermistor->sensor.assign_chan = ltc2983_thermistor_assign_chan; - ret =of_property_read_u32 (child,"adi,excitation-current-nanoamp" , - &excitation_current); + ret =fwnode_property_read_u32 (child,"adi,excitation-current-nanoamp" , + &excitation_current);if (ret) {/* Auto range is not allowed for custom sensors */ if (sensor->type >=LTC2983_SENSOR_THERMISTOR_STEINHART )@@ -999,17 +1002,16 @@ static struct ltc2983_sensor *ltc2983_thermistor_new( } } -of_node_put (phandle); +fwnode_handle_put (ref);return &thermistor->sensor; fail: -of_node_put (phandle); +fwnode_handle_put (ref);return ERR_PTR (ret); }
Re: [PATCH v1 2/2] iio: temperature: ltc2983: Make use of device properties
Quoted 11 lines · Jonathan Cameron
Quoted 2 lines · On Thu, 3 Feb 2022 13:45:06 +0200 Andy Shevchenko…
Convert the module to be property provider agnostic and allow it to be used on non-OF platforms.
This description needs expansion as it's not a straight forward conversion.
Also, complex enough that I definitely want more eyes and preferably some testing.
That's fair. I also spent most of the time on this change in comparison to the whole bundle.
...
Quoted 5 lines
drivers/iio/temperature/ltc2983.c line 22
Quoted 2 lines
drivers/iio/temperature/ltc2983.c +2
-0+#include <asm/byteorder.h> +#include <asm/unaligned.h> This may well be a valid addition but it's not called out in the patch description.
This is a side effect of the change. Below I will try to explain, tell me if that is what you want to be added to the commit message (feel free to correct my English).
The conversion slightly changes the logic behind property reading for the configuration values. Original code allocates just as much memory as needed. Then for each separate 32- or 64-bit value it reads it from the property and converts to a raw one which will be fed to the sensor. In the new code we allocated the amount of memory needed to retrieve all values at once from the property and then convert them as required.
...
Quoted 7 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( · line 422
Quoted 4 lines
drivers/iio/temperature/ltc2983.c +1
-2if (st->custom_table_size + new_custom->size > - (LTC2983_CUST_SENS_TBL_END_REG - -LTC2983_CUST_SENS_TBL_START_REG ) +1 ) { + (LTC2983_CUST_SENS_TBL_END_REG -LTC2983_CUST_SENS_TBL_START_REG ) +1 ) {Shouldn't really be in this patch. Or at very least call out that there is whitespace cleanup in the patch description.
Good catch! It's a leftover, one case became a patch 1 in this series.
...
Quoted 10 lines
Quoted 10 lines
drivers/iio/temperature/ltc2983.c +10
-0+if (is_steinhart) + ret =fwnode_property_read_u32_array (fn, propname, new_custom->table, n_entries); +else + ret =fwnode_property_read_u64_array (fn, propname, new_custom->table, n_entries); +if (ret <0 ) +return ERR_PTR (ret); + +/* +* Steinhart sensors are configured with raw values in the device tree. +* For the other sensors we must convert the value to raw. The odd
Quoted 8 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( · line 450
Quoted 5 lines
drivers/iio/temperature/ltc2983.c +5
-0+* index's correspond to temperatures and always have 1/1024 of +* resolution. Temperatures also come in Kelvin, so signed values is +* not possible. +*/ +if (is_steinhart) {Perhaps would be cleaner to combine this if else with the one above at the cost of duplicating the if (ret < 0) check.
OK, I'm fine with either approach.
Quoted 4 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( · line 451
Quoted 1 line
drivers/iio/temperature/ltc2983.c +1
-0+cpu_to_be32_array (new_custom->table, new_custom->table, n_entries);I completely failed to register the hand coded big endian conversion. Nice tidy up. However, definitely something to call out in the patch description.
See above.
Quoted 22 lines
Quoted 22 lines
drivers/iio/temperature/ltc2983.c +4
-8+ }else { +for (index =0 ; index < n_entries; index++) { +u64 temp = ((u64 *)new_custom->table)[index];if ((index %2 ) !=0 ) temp =__convert_to_raw (temp,1024 );@@ -445,16 +459,9 @@ static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( temp =__convert_to_raw_sign (temp, resolution); else temp =__convert_to_raw (temp, resolution); - }else { -u32 t32; -of_property_read_u32_index (np, propname, index, &t32); - temp = t32; +put_unaligned_be24 (temp, new_custom->table + index *3 ); } - -for (j =0 ; j < n_size; j++) - new_custom->table[tbl++] = - temp >> (8 * (n_size - j -1 )); }
...
Quoted 6 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child, · line 810
Quoted 3 lines
drivers/iio/temperature/ltc2983.c +1
-1if (IS_ERR (rtd->custom)) { -of_node_put (phandle); +fwnode_handle_put (ref);I guess there was a bunch of cut and paste in this driver ;) Same question as below on whether we can just use a goto here to share the put in the fail path.
Probably as separate (preparatory) patch?
Quoted 2 lines
Quoted 2 lines
drivers/iio/temperature/ltc2983.c +0
-0return ERR_CAST (rtd->custom); }
...
Quoted 9 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_sensor *ltc2983_thermistor_new( · line 933
Quoted 4 lines
drivers/iio/temperature/ltc2983.c +1
-1if (IS_ERR (thermistor->custom)) { -of_node_put (phandle); +fwnode_handle_put (ref);return ERR_CAST (thermistor->custom);Obviously not due to this patch, but this is odd. Why have one error path that doesn't use the goto faill;?
If you could tidy that up and add a note on it to the patch description that would be great.
Same answer as above.
Quoted 1 line
Quoted 1 line
}
Signature · 2 lines
With Best Regards, Andy Shevchenko
Sa, Nuno
maintainerRE: [PATCH v1 2/2] iio: temperature: ltc2983: Make use of device properties
Hi all,
Quoted 42 lines
-----Original Message-----
From: Andy Shevchenko <[email protected]>
Sent: Saturday, February 5, 2022 7:24 PM
To: Jonathan Cameron <[email protected]>
Cc: [email protected]; [email protected]; Sa, Nuno <[email protected]>; Lars-Peter Clausen <[email protected]>
Subject: Re: [PATCH v1 2/2] iio: temperature: ltc2983: Make use of device properties[External]
Quoted 10 lines · Jonathan Cameron
Quoted 2 lines · On Thu, 3 Feb 2022 13:45:06 +0200 Andy Shevchenko…
Convert the module to be property provider agnostic and allow it to be used on non-OF platforms.
This description needs expansion as it's not a straight forward conversion.
Also, complex enough that I definitely want more eyes and
preferably
Quoted 1 line
some testing.
That's fair. I also spent most of the time on this change in comparison to the
whole bundle....
Quoted 5 lines
drivers/iio/temperature/ltc2983.c line 22
Quoted 2 lines
drivers/iio/temperature/ltc2983.c +2
-0+#include <asm/byteorder.h> +#include <asm/unaligned.h> This may well be a valid addition but it's not called out in the patch description.
This is a side effect of the change. Below I will try to explain, tell me if that is what you want to be added to the commit message (feel free to correct
my English).
Quoted 10 lines
The conversion slightly changes the logic behind property reading for the
configuration values. Original code allocates just as much memory as needed.
Then for each separate 32- or 64-bit value it reads it from the property and converts to a raw one which will be fed to the sensor. In the new code
we allocated the amount of memory needed to retrieve all values at once from
the property and then convert them as required.
Yeah, I understood what you are doing... We allocate some extra bytes so that we can simplify a lot the logic to get, convert and put back the properties in the table... And since we are only writing the __real__ table size into the device I'm fairly positive this works. However, I do agree with Jonathan and I would be more confident to give this a test before being applied...
That said, I'm off till the end of the month (just doing minor stuff like replying to emails :)), so if we can hold this one, I will test it first thing I'm back in the office.
Quoted 43 lines
...
Quoted 4 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new(
Quoted 4 lines
drivers/iio/temperature/ltc2983.c +1
-2if (st->custom_table_size + new_custom->size > - (LTC2983_CUST_SENS_TBL_END_REG - -LTC2983_CUST_SENS_TBL_START_REG ) +1 ) { + (LTC2983_CUST_SENS_TBL_END_REG -
LTC2983_CUST_SENS_TBL_START_REG) + 1) {Quoted 3 lines
Shouldn't really be in this patch. Or at very least call out that there is whitespace cleanup in the patch description.
Good catch! It's a leftover, one case became a patch 1 in this series.
...
Quoted 2 lines
Review
Quoted 2 lines
(quoted diff) +2
-0+ if (is_steinhart) + ret = fwnode_property_read_u32_array(fn,propname,
new_custom->table,n_entries);Quoted 2 lines
Review
Quoted 2 lines
(quoted diff) +2
-0+ else + ret = fwnode_property_read_u64_array(fn,propname,
new_custom->table,n_entries);Quoted 5 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new(
Quoted 5 lines
drivers/iio/temperature/ltc2983.c +5
-0+if (ret <0 ) +return ERR_PTR (ret); + +/* +* Steinhart sensors are configured with raw values in the device tree.
Quoted 1 line
Review
Quoted 1 line
(quoted diff) +1
-0+ * For the other sensors we must convert the value to raw. Theodd
Quoted 1 line
Review
Quoted 1 line
(quoted diff) +1
-0+ * index's correspond to temperatures and always have 1/1024of
Quoted 1 line
Review
Quoted 1 line
(quoted diff) +1
-0+ * resolution. Temperatures also come in Kelvin, so signedvalues is
Quoted 5 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( · line 450
Quoted 3 lines
drivers/iio/temperature/ltc2983.c +3
-0+* not possible. +*/ +if (is_steinhart) {Perhaps would be cleaner to combine this if else with the one above
at the cost
Quoted 1 line
of duplicating the if (ret < 0) check.
OK, I'm fine with either approach.
Quoted 7 lines
Quoted 1 line
Review
Quoted 1 line
(quoted diff) +1
-0+ cpu_to_be32_array(new_custom->table,
new_custom->table,n_entries);Quoted 2 lines
I completely failed to register the hand coded big endian conversion.
Nice
Quoted 1 line
tidy up. However, definitely something to call out in the patch
description.
The hand coded big endian was done to not have to make a distinction between 3 and 4 bytes properties. With these changes it does not make sense anymore to have it...
- Nuno Sá
Re: [PATCH v1 2/2] iio: temperature: ltc2983: Make use of device properties
Quoted 5 lines · Nuno
Quoted 5 lines
From: Andy Shevchenko <[email protected]>
Sent: Saturday, February 5, 2022 7:24 PMQuoted 2 lines · Jonathan Cameron
On Thu, 3 Feb 2022 13:45:06 +0200
Andy Shevchenko <[email protected]> wrote:
...
Quoted 28 lines
Quoted 11 lines
Quoted 5 lines
drivers/iio/temperature/ltc2983.c line 22
Quoted 2 lines
drivers/iio/temperature/ltc2983.c +2
-0+#include <asm/byteorder.h> +#include <asm/unaligned.h> This may well be a valid addition but it's not called out in the patch description.
This is a side effect of the change. Below I will try to explain, tell me if that is what you want to be added to the commit message (feel free to correct
my English).Quoted 10 lines
The conversion slightly changes the logic behind property reading for the
configuration values. Original code allocates just as much memory as needed.
Then for each separate 32- or 64-bit value it reads it from the property and converts to a raw one which will be fed to the sensor. In the new code
we allocated the amount of memory needed to retrieve all values at once from
the property and then convert them as required.Yeah, I understood what you are doing... We allocate some extra bytes so that we can simplify a lot the logic to get, convert and put back the properties in the table... And since we are only writing the
__real__table size into the device I'm fairly positive this works. However, I do agree with Jonathan and I would be more confident to give this a test before being applied...
Quoted 3 lines
That said, I'm off till the end of the month (just doing minor stuff like replying to emails :)), so if we can hold this one, I will test it first thing I'm back in the office.
Will wait for your testing. Meanwhile I address all other comments and send v3 for further review.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Jonathan Cameron
maintainerRe: [PATCH v1 2/2] iio: temperature: ltc2983: Make use of device properties
In reply to Andy ShevchenkoQuoted 24 lines · On Sat, 5 Feb 2022 20:23:43 +0200 Andy Shevchenko…
Quoted 11 lines · Jonathan Cameron
Quoted 2 lines · On Thu, 3 Feb 2022 13:45:06 +0200 Andy Shevchenko…
Convert the module to be property provider agnostic and allow it to be used on non-OF platforms.
This description needs expansion as it's not a straight forward conversion.
Also, complex enough that I definitely want more eyes and preferably some testing.
That's fair. I also spent most of the time on this change in comparison to the whole bundle.
...
Quoted 5 lines
drivers/iio/temperature/ltc2983.c line 22
Quoted 2 lines
drivers/iio/temperature/ltc2983.c +2
-0+#include <asm/byteorder.h> +#include <asm/unaligned.h> This may well be a valid addition but it's not called out in the patch description.
Quoted 3 lines
This is a side effect of the change. Below I will try to explain, tell me if that is what you want to be added to the commit message (feel free to correct my English).
I figured that out whilst it was sending but didn't hit cancel fast enough! :)
Quoted 7 lines
The conversion slightly changes the logic behind property reading for the configuration values. Original code allocates just as much memory as needed. Then for each separate 32- or 64-bit value it reads it from the property and converts to a raw one which will be fed to the sensor. In the new code we allocated the amount of memory needed to retrieve all values at once from the property and then convert them as required.
Good description to put in the patch description.
Quoted 68 lines
...
Quoted 7 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( · line 422
Quoted 4 lines
drivers/iio/temperature/ltc2983.c +1
-2if (st->custom_table_size + new_custom->size > - (LTC2983_CUST_SENS_TBL_END_REG - -LTC2983_CUST_SENS_TBL_START_REG ) +1 ) { + (LTC2983_CUST_SENS_TBL_END_REG -LTC2983_CUST_SENS_TBL_START_REG ) +1 ) {Shouldn't really be in this patch. Or at very least call out that there is whitespace cleanup in the patch description.
Good catch! It's a leftover, one case became a patch 1 in this series.
...
Quoted 10 lines
Quoted 10 lines
drivers/iio/temperature/ltc2983.c +10
-0+if (is_steinhart) + ret =fwnode_property_read_u32_array (fn, propname, new_custom->table, n_entries); +else + ret =fwnode_property_read_u64_array (fn, propname, new_custom->table, n_entries); +if (ret <0 ) +return ERR_PTR (ret); + +/* +* Steinhart sensors are configured with raw values in the device tree. +* For the other sensors we must convert the value to raw. The odd Quoted 8 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( · line 450
Quoted 5 lines
drivers/iio/temperature/ltc2983.c +5
-0+* index's correspond to temperatures and always have 1/1024 of +* resolution. Temperatures also come in Kelvin, so signed values is +* not possible. +*/ +if (is_steinhart) {Perhaps would be cleaner to combine this if else with the one above at the cost of duplicating the if (ret < 0) check.
OK, I'm fine with either approach.
Quoted 4 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( · line 451
Quoted 1 line
drivers/iio/temperature/ltc2983.c +1
-0+cpu_to_be32_array (new_custom->table, new_custom->table, n_entries);I completely failed to register the hand coded big endian conversion. Nice tidy up. However, definitely something to call out in the patch description.
See above.
Quoted 22 lines
Quoted 22 lines
drivers/iio/temperature/ltc2983.c +4
-8+ }else { +for (index =0 ; index < n_entries; index++) { +u64 temp = ((u64 *)new_custom->table)[index];if ((index %2 ) !=0 ) temp =__convert_to_raw (temp,1024 );@@ -445,16 +459,9 @@ static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new( temp =__convert_to_raw_sign (temp, resolution); else temp =__convert_to_raw (temp, resolution); - }else { -u32 t32; -of_property_read_u32_index (np, propname, index, &t32); - temp = t32; +put_unaligned_be24 (temp, new_custom->table + index *3 ); } - -for (j =0 ; j < n_size; j++) - new_custom->table[tbl++] = - temp >> (8 * (n_size - j -1 )); }...
Quoted 8 lines
Quoted 6 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child, · line 810
Quoted 3 lines
drivers/iio/temperature/ltc2983.c +1
-1if (IS_ERR (rtd->custom)) { -of_node_put (phandle); +fwnode_handle_put (ref);I guess there was a bunch of cut and paste in this driver ;) Same question as below on whether we can just use a goto here to share the put in the fail path.
Probably as separate (preparatory) patch?
Perfect
Quoted 20 lines
Quoted 3 lines
Quoted 3 lines
drivers/iio/temperature/ltc2983.c +0
-0return ERR_CAST (rtd->custom); }...
Quoted 9 lines
drivers/iio/temperature/ltc2983.c static struct ltc2983_sensor *ltc2983_thermistor_new( · line 933
Quoted 4 lines
drivers/iio/temperature/ltc2983.c +1
-1if (IS_ERR (thermistor->custom)) { -of_node_put (phandle); +fwnode_handle_put (ref);return ERR_CAST (thermistor->custom);Obviously not due to this patch, but this is odd. Why have one error path that doesn't use the goto faill;?
If you could tidy that up and add a note on it to the patch description that would be great.Same answer as above.
Quoted 1 line
Quoted 1 line
}
Quoted 12 lines
-----Original Message-----
From: Andy Shevchenko <[email protected]>
Sent: Thursday, February 3, 2022 12:45 PM
To: Andy Shevchenko <[email protected]>; linux- [email protected]; [email protected]
Cc: Sa, Nuno <[email protected]>; Jonathan Cameron <[email protected]>; Lars-Peter Clausen <[email protected]>
Subject: [PATCH v1 1/2] iio: temperature: ltc2983: Don't hard code defined constants in messages
Quoted 8 lines
[External]
In a couple of messages the constants, which have their definitions, are hard coded into the message text. Unhardcode them.
Signed-off-by: Andy Shevchenko
<[email protected]>
---