Skip to contentSkip to conversation

drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities

PATCH Superseded Imre Deak 3 participants 12 messages Feb 28, 2022 – Mar 22, 2022

Subsystems (4)
lore
Share & tools
lore

Imre Deak

author
#0 lore raw

PATCH 1/1 drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities

At least some DELL monitors (P2715Q) with DPCD_REV 1.2 return corrupted DPCD register values when reading from the 0xF0000- LTTPR range with an AUX transaction block size bigger than 1. The DP standard requires 0 to be returned - as for any other reserved/invalid addresses - but these monitors return the DPCD_REV register value repeated in each byte of the read buffer. This will in turn corrupt the values returned by the LTTPRs between the source and the monitor: LTTPRs must adjust the values they read from the downstream DPRX, for instance left-shift/init the downstream DP_PHY_REPEATER_CNT value. Since the value returned by the monitor's DPRX is non-zero the adjusted values will be corrupt.

Reading the LTTPR registers one-by-one instead of reading all of them with a single AUX transfer works around the issue.

According to the DP standard's 0xF0000 register description:
"LTTPR-related registers at DPCD Addresses F0000h through F02FFh are valid only for DPCD r1.4 (or higher)." While it's unclear if DPCD r1.4 refers to the DPCD_REV or to the LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV register (tickets filed at the VESA site to clarify this haven't been addressed), one possibility is that it's a restriction due to non-compliant monitors described above. Disabling the non-transparent LTTPR mode for all such monitors is not a viable solution: the transparent LTTPR mode has its own issue causing link training failures and this would affect a lot of monitors in use with DPCD_REV < 1.4. Instead this patch works around the problem by reading the LTTPR common and PHY cap registers one-by-one for any monitor with a DPCD_REV < 1.4.

The standard requires the DPCD capabilites to be read after the LTTPR common capabilities are read, so re-read the DPCD capabilities after the LTTPR common and PHY caps were read out.

---
 drivers/gpu/drm/dp/drm_dp.c                   | 58 ++++++++++++-------
 .../drm/i915/display/intel_dp_link_training.c | 30 +++++++---
 include/drm/dp/drm_dp_helper.h                |  2 +
 3 files changed, 59 insertions(+), 31 deletions(-)
drivers/gpu/drm/dp/drm_dp.c +36 -22
index 703972ae14c64..f3950d42980f9 100644
@@ -2390,9 +2390,36 @@ int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_S
 }
 EXPORT_SYMBOL(drm_dp_dsc_sink_supported_input_bpcs);
 
+static int drm_dp_read_lttpr_regs(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], int address,
+				  u8 *buf, int buf_size)
+{
+	/*
+	 * Some monitors with a DPCD_REV < 0x14 return corrupted values when
+	 * reading from the 0xF0000- range with a block size bigger than 1.
+	 */
+	int block_size = dpcd[DP_DPCD_REV] < 0x14 ? 1 : buf_size;
+	int offset = 0;
+	int ret;
+
+	while (offset < buf_size) {
+		ret = drm_dp_dpcd_read(aux,
+				       address + offset,
+				       &buf[offset], block_size);
+		if (ret < 0)
+			return ret;
+
+		WARN_ON(ret != block_size);
+
+		offset += block_size;
+	}
+
+	return 0;
+}
+
 /**
  * drm_dp_read_lttpr_common_caps - read the LTTPR common capabilities
  * @aux: DisplayPort AUX channel
+ * @dpcd: DisplayPort configuration data
  * @caps: buffer to return the capability info in
  *
  * Read capabilities common to all LTTPRs.
@@ -2400,25 +2427,19 @@ EXPORT_SYMBOL(drm_dp_dsc_sink_supported_input_bpcs);
  * Returns 0 on success or a negative error code on failure.
  */
 int drm_dp_read_lttpr_common_caps(struct drm_dp_aux *aux,
+				  const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 				  u8 caps[DP_LTTPR_COMMON_CAP_SIZE])
 {
-	int ret;
-
-	ret = drm_dp_dpcd_read(aux,
-			       DP_LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV,
-			       caps, DP_LTTPR_COMMON_CAP_SIZE);
-	if (ret < 0)
-		return ret;
-
-	WARN_ON(ret != DP_LTTPR_COMMON_CAP_SIZE);
-
-	return 0;
+	return drm_dp_read_lttpr_regs(aux, dpcd,
+				      DP_LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV,
+				      caps, DP_LTTPR_COMMON_CAP_SIZE);
 }
 EXPORT_SYMBOL(drm_dp_read_lttpr_common_caps);
 
 /**
  * drm_dp_read_lttpr_phy_caps - read the capabilities for a given LTTPR PHY
  * @aux: DisplayPort AUX channel
+ * @dpcd: DisplayPort configuration data
  * @dp_phy: LTTPR PHY to read the capabilities for
  * @caps: buffer to return the capability info in
  *
@@ -2427,20 +2448,13 @@ EXPORT_SYMBOL(drm_dp_read_lttpr_common_caps);
  * Returns 0 on success or a negative error code on failure.
  */
 int drm_dp_read_lttpr_phy_caps(struct drm_dp_aux *aux,
+			       const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 			       enum drm_dp_phy dp_phy,
 			       u8 caps[DP_LTTPR_PHY_CAP_SIZE])
 {
-	int ret;
-
-	ret = drm_dp_dpcd_read(aux,
-			       DP_TRAINING_AUX_RD_INTERVAL_PHY_REPEATER(dp_phy),
-			       caps, DP_LTTPR_PHY_CAP_SIZE);
-	if (ret < 0)
-		return ret;
-
-	WARN_ON(ret != DP_LTTPR_PHY_CAP_SIZE);
-
-	return 0;
+	return drm_dp_read_lttpr_regs(aux, dpcd,
+				      DP_TRAINING_AUX_RD_INTERVAL_PHY_REPEATER(dp_phy),
+				      caps, DP_LTTPR_PHY_CAP_SIZE);
 }
 EXPORT_SYMBOL(drm_dp_read_lttpr_phy_caps);
 
drivers/gpu/drm/i915/display/intel_dp_link_training.c +21 -9
index 5d98773efd1b3..fbee20a76cf44 100644
@@ -55,6 +55,7 @@ static u8 *intel_dp_lttpr_phy_caps(struct intel_dp *intel_dp,
 }
 
 static void intel_dp_read_lttpr_phy_caps(struct intel_dp *intel_dp,
+					 const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 					 enum drm_dp_phy dp_phy)
 {
 	struct intel_encoder *encoder = &dp_to_dig_port(intel_dp)->base;
@@ -63,7 +64,7 @@ static void intel_dp_read_lttpr_phy_caps(struct intel_dp *intel_dp,
 
 	intel_dp_phy_name(dp_phy, phy_name, sizeof(phy_name));
 
-	if (drm_dp_read_lttpr_phy_caps(&intel_dp->aux, dp_phy, phy_caps) < 0) {
+	if (drm_dp_read_lttpr_phy_caps(&intel_dp->aux, dpcd, dp_phy, phy_caps) < 0) {
 		drm_dbg_kms(&dp_to_i915(intel_dp)->drm,
 			    "[ENCODER:%d:%s][%s] failed to read the PHY caps\n",
 			    encoder->base.base.id, encoder->base.name, phy_name);
@@ -77,10 +78,11 @@ static void intel_dp_read_lttpr_phy_caps(struct intel_dp *intel_dp,
 		    phy_caps);
 }
 
-static bool intel_dp_read_lttpr_common_caps(struct intel_dp *intel_dp)
+static bool intel_dp_read_lttpr_common_caps(struct intel_dp *intel_dp, const u8 dpcd[DP_RECEIVER_CAP_SIZE])
 {
 	struct intel_encoder *encoder = &dp_to_dig_port(intel_dp)->base;
 	struct drm_i915_private *i915 = to_i915(encoder->base.dev);
+	int ret;
 
 	if (intel_dp_is_edp(intel_dp))
 		return false;
@@ -92,8 +94,9 @@ static bool intel_dp_read_lttpr_common_caps(struct intel_dp *intel_dp)
 	if (DISPLAY_VER(i915) < 10 || IS_GEMINILAKE(i915))
 		return false;
 
-	if (drm_dp_read_lttpr_common_caps(&intel_dp->aux,
-					  intel_dp->lttpr_common_caps) < 0)
+	ret = drm_dp_read_lttpr_common_caps(&intel_dp->aux, dpcd,
+					    intel_dp->lttpr_common_caps);
+	if (ret < 0)
 		goto reset_caps;
 
 	drm_dbg_kms(&dp_to_i915(intel_dp)->drm,
@@ -122,14 +125,14 @@ intel_dp_set_lttpr_transparent_mode(struct intel_dp *intel_dp, bool enable)
 	return drm_dp_dpcd_write(&intel_dp->aux, DP_PHY_REPEATER_MODE, &val, 1) == 1;
 }
 
-static int intel_dp_init_lttpr(struct intel_dp *intel_dp)
+static int intel_dp_init_lttpr(struct intel_dp *intel_dp, const u8 dpcd[DP_RECEIVER_CAP_SIZE])
 {
 	struct intel_encoder *encoder = &dp_to_dig_port(intel_dp)->base;
 	struct drm_i915_private *i915 = to_i915(encoder->base.dev);
 	int lttpr_count;
 	int i;
 
-	if (!intel_dp_read_lttpr_common_caps(intel_dp))
+	if (!intel_dp_read_lttpr_common_caps(intel_dp, dpcd))
 		return 0;
 
 	lttpr_count = drm_dp_lttpr_count(intel_dp->lttpr_common_caps);
@@ -168,7 +171,7 @@ static int intel_dp_init_lttpr(struct intel_dp *intel_dp)
 	}
 
 	for (i = 0; i < lttpr_count; i++)
-		intel_dp_read_lttpr_phy_caps(intel_dp, DP_PHY_LTTPR(i));
+		intel_dp_read_lttpr_phy_caps(intel_dp, dpcd, DP_PHY_LTTPR(i));
 
 	return lttpr_count;
 }
@@ -193,9 +196,18 @@ static int intel_dp_init_lttpr(struct intel_dp *intel_dp)
  */
 int intel_dp_init_lttpr_and_dprx_caps(struct intel_dp *intel_dp)
 {
-	int lttpr_count = intel_dp_init_lttpr(intel_dp);
+	u8 dpcd[DP_RECEIVER_CAP_SIZE];
+	int lttpr_count;
 
-	/* The DPTX shall read the DPRX caps after LTTPR detection. */
+	if (drm_dp_read_dpcd_caps(&intel_dp->aux, dpcd))
+		return -EIO;
+
+	lttpr_count = intel_dp_init_lttpr(intel_dp, dpcd);
+
+	/*
+	 * The DPTX shall read the DPRX caps after LTTPR detection, so re-read
+	 * it here.
+	 */
 	if (drm_dp_read_dpcd_caps(&intel_dp->aux, intel_dp->dpcd)) {
 		intel_dp_reset_lttpr_common_caps(intel_dp);
 		return -EIO;
include/drm/dp/drm_dp_helper.h +2 -0
index 51e02cf75277e..1eccd97419436 100644
@@ -2148,8 +2148,10 @@ bool drm_dp_read_sink_count_cap(struct drm_connector *connector,
 int drm_dp_read_sink_count(struct drm_dp_aux *aux);
 
 int drm_dp_read_lttpr_common_caps(struct drm_dp_aux *aux,
+				  const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 				  u8 caps[DP_LTTPR_COMMON_CAP_SIZE]);
 int drm_dp_read_lttpr_phy_caps(struct drm_dp_aux *aux,
+			       const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 			       enum drm_dp_phy dp_phy,
 			       u8 caps[DP_LTTPR_PHY_CAP_SIZE]);
 int drm_dp_lttpr_count(const u8 cap[DP_LTTPR_COMMON_CAP_SIZE]);
Signature · 1 line
2.27.0
#1 lore raw

[Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities

== Series Details ==

== Series Details ==

Series: drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities
URL : https://patchwork.freedesktop.org/series/100851/
State : warning

== Summary ==

$ dim checkpatch origin/drm-tip
7ba5645d82fa drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities
-:35: WARNING:TYPO_SPELLING: 'capabilites' may be misspelled - perhaps 'capabilities'?
#35: 
The standard requires the DPCD capabilites to be read after the LTTPR
                               ^^^^^^^^^^^

-:50: WARNING:LONG_LINE: line length of 107 exceeds 100 columns
#50: FILE: drivers/gpu/drm/dp/drm_dp.c:2393:
+static int drm_dp_read_lttpr_regs(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], int address,

-:165: WARNING:LONG_LINE: line length of 107 exceeds 100 columns
#165: FILE: drivers/gpu/drm/i915/display/intel_dp_link_training.c:81:
+static bool intel_dp_read_lttpr_common_caps(struct intel_dp *intel_dp, const u8 dpcd[DP_RECEIVER_CAP_SIZE])

total: 0 errors, 3 warnings, 0 checks, 182 lines checked

#2 lore raw

[Intel-gfx] ✓ Fi.CI.BAT: success for drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities

In reply to Imre Deak
== Series Details ==

== Series Details ==

Series: drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities
URL : https://patchwork.freedesktop.org/series/100851/
State : success

== Summary ==

CI Bug Log - changes from CI_DRM_11300 -> Patchwork_22441
====================================================

Summary
-------

**SUCCESS**

No regressions found.

External URL: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22441/index.html

Participating hosts (46 -> 33)
------------------------------

Missing (13): fi-bdw-samus shard-tglu bat-dg1-6 bat-dg1-5 shard-rkl bat-dg2-9 fi-bsw-cyan bat-adlp-6 bat-adlp-4 fi-pnv-d510 bat-rpls-2 shard-dg1 bat-jsl-1

Known issues
------------

Here are the changes found in Patchwork_22441 that come from known issues:

### IGT changes ###

#### Issues hit ####

* igt@amdgpu/amd_basic@cs-multi-fence:
- fi-blb-e6850: NOTRUN -> [SKIP][1] ([fdo#109271]) +17 similar issues
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22441/fi-blb-e6850/igt@amdgpu/[email protected]

* igt@gem_flink_basic@bad-flink:
- fi-skl-6600u: [PASS][2] -> [INCOMPLETE][3] ([i915#4547])
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11300/fi-skl-6600u/igt@[email protected]
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22441/fi-skl-6600u/igt@[email protected]

* igt@i915_selftest@live@hangcheck:
- fi-rkl-guc: [PASS][4] -> [INCOMPLETE][5] ([i915#4983])
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11300/fi-rkl-guc/igt@i915_selftest@[email protected]
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22441/fi-rkl-guc/igt@i915_selftest@[email protected]

#### Possible fixes ####

* igt@i915_selftest@live@gt_heartbeat:
- fi-glk-dsi: [DMESG-FAIL][6] ([i915#541]) -> [PASS][7]
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11300/fi-glk-dsi/igt@i915_selftest@live@gt_heartbeat.html
[7]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22441/fi-glk-dsi/igt@i915_selftest@live@gt_heartbeat.html

* igt@i915_selftest@live@requests:
- fi-blb-e6850: [DMESG-FAIL][8] ([i915#5026]) -> [PASS][9]
[8]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11300/fi-blb-e6850/igt@i915_selftest@[email protected]
[9]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22441/fi-blb-e6850/igt@i915_selftest@[email protected]

* igt@kms_force_connector_basic@force-connector-state:
- fi-cfl-8109u: [DMESG-WARN][10] ([i915#165]) -> [PASS][11] +1 similar issue
[10]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11300/fi-cfl-8109u/igt@[email protected]
[11]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22441/fi-cfl-8109u/igt@[email protected]

* igt@kms_pipe_crc_basic@compare-crc-sanitycheck-pipe-b:
- fi-cfl-8109u: [DMESG-WARN][12] ([i915#165] / [i915#295]) -> [PASS][13] +13 similar issues
[12]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11300/fi-cfl-8109u/igt@[email protected]
[13]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22441/fi-cfl-8109u/igt@[email protected]

{name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).

[fdo#109271]: https://bugs.freedesktop.org/show_bug.cgi?id=109271
[i915#165]: https://gitlab.freedesktop.org/drm/intel/issues/165
[i915#295]: https://gitlab.freedesktop.org/drm/intel/issues/295
[i915#4547]: https://gitlab.freedesktop.org/drm/intel/issues/4547
[i915#4983]: https://gitlab.freedesktop.org/drm/intel/issues/4983
[i915#5026]: https://gitlab.freedesktop.org/drm/intel/issues/5026
[i915#5127]: https://gitlab.freedesktop.org/drm/intel/issues/5127
[i915#541]: https://gitlab.freedesktop.org/drm/intel/issues/541

Build changes
-------------

* Linux: CI_DRM_11300 -> Patchwork_22441

CI-20190529: 20190529
CI_DRM_11300: 10eb9bc8729d3da3fe8f53c8e5b70b8a9a52b6e0 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_6361: 2372a4beb6a33c5f0799a4a8ccbb93794f52dbca @ https://gitlab.freedesktop.org/drm/igt-gpu-tools.git
Patchwork_22441: 7ba5645d82fa47b563026775f555df287a6d59bb @ git://anongit.freedesktop.org/gfx-ci/linux

== Linux commits ==

7ba5645d82fa drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22441/index.html

#3 lore raw
In reply to Imre Deak
Quoted 45 lines · Imre Deak

At least some DELL monitors (P2715Q) with DPCD_REV 1.2 return corrupted DPCD register values when reading from the 0xF0000- LTTPR range with an AUX transaction block size bigger than 1. The DP standard requires 0 to be returned - as for any other reserved/invalid addresses - but these monitors return the DPCD_REV register value repeated in each byte of the read buffer. This will in turn corrupt the values returned by the LTTPRs between the source and the monitor: LTTPRs must adjust the values they read from the downstream DPRX, for instance left-shift/init the downstream DP_PHY_REPEATER_CNT value. Since the value returned by the monitor's DPRX is non-zero the adjusted values will be corrupt.

Reading the LTTPR registers one-by-one instead of reading all of them with a single AUX transfer works around the issue.

According to the DP standard's 0xF0000 register description:
"LTTPR-related registers at DPCD Addresses F0000h through F02FFh are valid only for DPCD r1.4 (or higher)." While it's unclear if DPCD r1.4 refers to the DPCD_REV or to the LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV register (tickets filed at the VESA site to clarify this haven't been addressed), one possibility is that it's a restriction due to non-compliant monitors described above. Disabling the non-transparent LTTPR mode for all such monitors is not a viable solution: the transparent LTTPR mode has its own issue causing link training failures and this would affect a lot of monitors in use with DPCD_REV < 1.4. Instead this patch works around the problem by reading the LTTPR common and PHY cap registers one-by-one for any monitor with a DPCD_REV < 1.4.

The standard requires the DPCD capabilites to be read after the LTTPR common capabilities are read, so re-read the DPCD capabilities after the LTTPR common and PHY caps were read out.

---
 drivers/gpu/drm/dp/drm_dp.c                   | 58 ++++++++++++-------
 .../drm/i915/display/intel_dp_link_training.c | 30 +++++++---
 include/drm/dp/drm_dp_helper.h                |  2 +
 3 files changed, 59 insertions(+), 31 deletions(-)
drivers/gpu/drm/dp/drm_dp.c +0 -0
index 703972ae14c64..f3950d42980f9 100644

drivers/gpu/drm/dp/drm_dp.c int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_S · line 2399

Quoted 10 lines
drivers/gpu/drm/dp/drm_dp.c +7 -0
@@ -2390,9 +2390,36 @@ int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_S
 }
 EXPORT_SYMBOL(drm_dp_dsc_sink_supported_input_bpcs);
 
+static int drm_dp_read_lttpr_regs(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], int address,
+				  u8 *buf, int buf_size)
+{
+	/*
+	 * Some monitors with a DPCD_REV < 0x14 return corrupted values when
+	 * reading from the 0xF0000- range with a block size bigger than 1.
+	 */

This sounds really scary. Have we checked what other registers might end up corrupted? Eg. couple of rounds of comparing full dd bs=1 vs. dd bs=16.

drivers/gpu/drm/dp/drm_dp.c int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_S · line 2404

Quoted 5 lines
drivers/gpu/drm/dp/drm_dp.c +5 -0
+	int block_size = dpcd[DP_DPCD_REV] < 0x14 ? 1 : buf_size;
+	int offset = 0;
+	int ret;
+
+	while (offset < buf_size) {

Can we use a for loop?

Quoted 14 lines
drivers/gpu/drm/dp/drm_dp.c +14 -0
+		ret = drm_dp_dpcd_read(aux,
+				       address + offset,
+				       &buf[offset], block_size);
+		if (ret < 0)
+			return ret;
+
+		WARN_ON(ret != block_size);
+
+		offset += block_size;
+	}
+
+	return 0;
+}
+
Signature · 2 lines
Ville Syrjälä
Intel
author
#4 lore raw
Quoted 49 lines · Ville Syrjälä
Quoted 48 lines · Imre Deak

At least some DELL monitors (P2715Q) with DPCD_REV 1.2 return corrupted DPCD register values when reading from the 0xF0000- LTTPR range with an AUX transaction block size bigger than 1. The DP standard requires 0 to be returned - as for any other reserved/invalid addresses - but these monitors return the DPCD_REV register value repeated in each byte of the read buffer. This will in turn corrupt the values returned by the LTTPRs between the source and the monitor: LTTPRs must adjust the values they read from the downstream DPRX, for instance left-shift/init the downstream DP_PHY_REPEATER_CNT value. Since the value returned by the monitor's DPRX is non-zero the adjusted values will be corrupt.

Reading the LTTPR registers one-by-one instead of reading all of them with a single AUX transfer works around the issue.

According to the DP standard's 0xF0000 register description:
"LTTPR-related registers at DPCD Addresses F0000h through F02FFh are valid only for DPCD r1.4 (or higher)." While it's unclear if DPCD r1.4 refers to the DPCD_REV or to the LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV register (tickets filed at the VESA site to clarify this haven't been addressed), one possibility is that it's a restriction due to non-compliant monitors described above. Disabling the non-transparent LTTPR mode for all such monitors is not a viable solution: the transparent LTTPR mode has its own issue causing link training failures and this would affect a lot of monitors in use with DPCD_REV < 1.4. Instead this patch works around the problem by reading the LTTPR common and PHY cap registers one-by-one for any monitor with a DPCD_REV < 1.4.

The standard requires the DPCD capabilites to be read after the LTTPR common capabilities are read, so re-read the DPCD capabilities after the LTTPR common and PHY caps were read out.

---
 drivers/gpu/drm/dp/drm_dp.c                   | 58 ++++++++++++-------
 .../drm/i915/display/intel_dp_link_training.c | 30 +++++++---
 include/drm/dp/drm_dp_helper.h                |  2 +
 3 files changed, 59 insertions(+), 31 deletions(-)
drivers/gpu/drm/dp/drm_dp.c +0 -0
index 703972ae14c64..f3950d42980f9 100644
@@ -2390,9 +2390,36 @@ int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_S
 }
 EXPORT_SYMBOL(drm_dp_dsc_sink_supported_input_bpcs);
 
Quoted 11 lines

drivers/gpu/drm/dp/drm_dp.c int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_S · line 2399

Quoted 7 lines
drivers/gpu/drm/dp/drm_dp.c +7 -0
+static int drm_dp_read_lttpr_regs(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], int address,
+				  u8 *buf, int buf_size)
+{
+	/*
+	 * Some monitors with a DPCD_REV < 0x14 return corrupted values when
+	 * reading from the 0xF0000- range with a block size bigger than 1.
+	 */

This sounds really scary. Have we checked what other registers might end up corrupted? Eg. couple of rounds of comparing full dd bs=1 vs. dd bs=16.

Yes, checked now on a DELL P2715Q/ADLP/native-DP (w/o any LTTPR):

dd bs=1 count=1M failes at offset 81 and 83, bs=16 doesn't have this problem.

Replacing the above two bytes with 0s in the bs=1 output, the only difference is at 0xf0000:

bs=1:  0x12 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
bs=16: 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12

I attached the edid and bin files to the bugzilla ticket.

Quoted 7 lines

drivers/gpu/drm/dp/drm_dp.c int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_S · line 2404

Quoted 5 lines
drivers/gpu/drm/dp/drm_dp.c +5 -0
+	int block_size = dpcd[DP_DPCD_REV] < 0x14 ? 1 : buf_size;
+	int offset = 0;
+	int ret;
+
+	while (offset < buf_size) {

Can we use a for loop?

Yes, will change this.

Quoted 18 lines
Quoted 14 lines
drivers/gpu/drm/dp/drm_dp.c +14 -0
+		ret = drm_dp_dpcd_read(aux,
+				       address + offset,
+				       &buf[offset], block_size);
+		if (ret < 0)
+			return ret;
+
+		WARN_ON(ret != block_size);
+
+		offset += block_size;
+	}
+
+	return 0;
+}
+
Signature · 2 lines
Ville Syrjälä
Intel
#5 lore raw
Quoted 62 lines · Imre Deak
Quoted 49 lines · Ville Syrjälä
Quoted 48 lines · Imre Deak

At least some DELL monitors (P2715Q) with DPCD_REV 1.2 return corrupted DPCD register values when reading from the 0xF0000- LTTPR range with an AUX transaction block size bigger than 1. The DP standard requires 0 to be returned - as for any other reserved/invalid addresses - but these monitors return the DPCD_REV register value repeated in each byte of the read buffer. This will in turn corrupt the values returned by the LTTPRs between the source and the monitor: LTTPRs must adjust the values they read from the downstream DPRX, for instance left-shift/init the downstream DP_PHY_REPEATER_CNT value. Since the value returned by the monitor's DPRX is non-zero the adjusted values will be corrupt.

Reading the LTTPR registers one-by-one instead of reading all of them with a single AUX transfer works around the issue.

According to the DP standard's 0xF0000 register description:
"LTTPR-related registers at DPCD Addresses F0000h through F02FFh are valid only for DPCD r1.4 (or higher)." While it's unclear if DPCD r1.4 refers to the DPCD_REV or to the LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV register (tickets filed at the VESA site to clarify this haven't been addressed), one possibility is that it's a restriction due to non-compliant monitors described above. Disabling the non-transparent LTTPR mode for all such monitors is not a viable solution: the transparent LTTPR mode has its own issue causing link training failures and this would affect a lot of monitors in use with DPCD_REV < 1.4. Instead this patch works around the problem by reading the LTTPR common and PHY cap registers one-by-one for any monitor with a DPCD_REV < 1.4.

The standard requires the DPCD capabilites to be read after the LTTPR common capabilities are read, so re-read the DPCD capabilities after the LTTPR common and PHY caps were read out.

---
 drivers/gpu/drm/dp/drm_dp.c                   | 58 ++++++++++++-------
 .../drm/i915/display/intel_dp_link_training.c | 30 +++++++---
 include/drm/dp/drm_dp_helper.h                |  2 +
 3 files changed, 59 insertions(+), 31 deletions(-)
drivers/gpu/drm/dp/drm_dp.c +0 -0
index 703972ae14c64..f3950d42980f9 100644
@@ -2390,9 +2390,36 @@ int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_S
 }
 EXPORT_SYMBOL(drm_dp_dsc_sink_supported_input_bpcs);
 
Quoted 11 lines

drivers/gpu/drm/dp/drm_dp.c int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_S · line 2399

Quoted 7 lines
drivers/gpu/drm/dp/drm_dp.c +7 -0
+static int drm_dp_read_lttpr_regs(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], int address,
+				  u8 *buf, int buf_size)
+{
+	/*
+	 * Some monitors with a DPCD_REV < 0x14 return corrupted values when
+	 * reading from the 0xF0000- range with a block size bigger than 1.
+	 */

This sounds really scary. Have we checked what other registers might end up corrupted? Eg. couple of rounds of comparing full dd bs=1 vs. dd bs=16.

Quoted 4 lines

Yes, checked now on a DELL P2715Q/ADLP/native-DP (w/o any LTTPR):

dd bs=1 count=1M failes at offset 81 and 83, bs=16 doesn't have this problem.

Huh. Oh well, it's a Dell monitor after all. Not sure what else I was expecting tbh.

Signature · 2 lines
Ville Syrjälä
Intel
author
#6 lore raw

PATCH v2 1/1 drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities

In reply to Imre Deak

At least some DELL monitors (P2715Q) with DPCD_REV 1.2 return corrupted DPCD register values when reading from the 0xF0000- LTTPR range with an AUX transaction block size bigger than 1. The DP standard requires 0 to be returned - as for any other reserved/invalid addresses - but these monitors return the DPCD_REV register value repeated in each byte of the read buffer. This will in turn corrupt the values returned by the LTTPRs between the source and the monitor: LTTPRs must adjust the values they read from the downstream DPRX, for instance left-shift/init the downstream DP_PHY_REPEATER_CNT value. Since the value returned by the monitor's DPRX is non-zero the adjusted values will be corrupt.

Reading the LTTPR registers one-by-one instead of reading all of them with a single AUX transfer works around the issue.

According to the DP standard's 0xF0000 register description:
"LTTPR-related registers at DPCD Addresses F0000h through F02FFh are valid only for DPCD r1.4 (or higher)." While it's unclear if DPCD r1.4 refers to the DPCD_REV or to the LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV register (tickets filed at the VESA site to clarify this haven't been addressed), one possibility is that it's a restriction due to non-compliant monitors described above. Disabling the non-transparent LTTPR mode for all such monitors is not a viable solution: the transparent LTTPR mode has its own issue causing link training failures and this would affect a lot of monitors in use with DPCD_REV < 1.4. Instead this patch works around the problem by reading the LTTPR common and PHY cap registers one-by-one for any monitor with a DPCD_REV < 1.4.

The standard requires the DPCD capabilites to be read after the LTTPR common capabilities are read, so re-read the DPCD capabilities after the LTTPR common and PHY caps were read out.

v2:
- Use for instead of a while loop. (Ville)
- Add to code comment the monitor model with the problem.

---
 drivers/gpu/drm/dp/drm_dp.c                   | 57 ++++++++++++-------
 .../drm/i915/display/intel_dp_link_training.c | 30 +++++++---
 include/drm/dp/drm_dp_helper.h                |  2 +
 3 files changed, 58 insertions(+), 31 deletions(-)
drivers/gpu/drm/dp/drm_dp.c +35 -22
index 703972ae14c64..58744f83931af 100644
@@ -2390,9 +2390,35 @@ int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_S
 }
 EXPORT_SYMBOL(drm_dp_dsc_sink_supported_input_bpcs);
 
+static int drm_dp_read_lttpr_regs(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], int address,
+				  u8 *buf, int buf_size)
+{
+	/*
+	 * At least the DELL P2715Q monitor with a DPCD_REV < 0x14 returns
+	 * corrupted values when reading from the 0xF0000- range with a block
+	 * size bigger than 1.
+	 */
+	int block_size = dpcd[DP_DPCD_REV] < 0x14 ? 1 : buf_size;
+	int offset;
+	int ret;
+
+	for (offset = 0; offset < buf_size; offset += block_size) {
+		ret = drm_dp_dpcd_read(aux,
+				       address + offset,
+				       &buf[offset], block_size);
+		if (ret < 0)
+			return ret;
+
+		WARN_ON(ret != block_size);
+	}
+
+	return 0;
+}
+
 /**
  * drm_dp_read_lttpr_common_caps - read the LTTPR common capabilities
  * @aux: DisplayPort AUX channel
+ * @dpcd: DisplayPort configuration data
  * @caps: buffer to return the capability info in
  *
  * Read capabilities common to all LTTPRs.
@@ -2400,25 +2426,19 @@ EXPORT_SYMBOL(drm_dp_dsc_sink_supported_input_bpcs);
  * Returns 0 on success or a negative error code on failure.
  */
 int drm_dp_read_lttpr_common_caps(struct drm_dp_aux *aux,
+				  const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 				  u8 caps[DP_LTTPR_COMMON_CAP_SIZE])
 {
-	int ret;
-
-	ret = drm_dp_dpcd_read(aux,
-			       DP_LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV,
-			       caps, DP_LTTPR_COMMON_CAP_SIZE);
-	if (ret < 0)
-		return ret;
-
-	WARN_ON(ret != DP_LTTPR_COMMON_CAP_SIZE);
-
-	return 0;
+	return drm_dp_read_lttpr_regs(aux, dpcd,
+				      DP_LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV,
+				      caps, DP_LTTPR_COMMON_CAP_SIZE);
 }
 EXPORT_SYMBOL(drm_dp_read_lttpr_common_caps);
 
 /**
  * drm_dp_read_lttpr_phy_caps - read the capabilities for a given LTTPR PHY
  * @aux: DisplayPort AUX channel
+ * @dpcd: DisplayPort configuration data
  * @dp_phy: LTTPR PHY to read the capabilities for
  * @caps: buffer to return the capability info in
  *
@@ -2427,20 +2447,13 @@ EXPORT_SYMBOL(drm_dp_read_lttpr_common_caps);
  * Returns 0 on success or a negative error code on failure.
  */
 int drm_dp_read_lttpr_phy_caps(struct drm_dp_aux *aux,
+			       const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 			       enum drm_dp_phy dp_phy,
 			       u8 caps[DP_LTTPR_PHY_CAP_SIZE])
 {
-	int ret;
-
-	ret = drm_dp_dpcd_read(aux,
-			       DP_TRAINING_AUX_RD_INTERVAL_PHY_REPEATER(dp_phy),
-			       caps, DP_LTTPR_PHY_CAP_SIZE);
-	if (ret < 0)
-		return ret;
-
-	WARN_ON(ret != DP_LTTPR_PHY_CAP_SIZE);
-
-	return 0;
+	return drm_dp_read_lttpr_regs(aux, dpcd,
+				      DP_TRAINING_AUX_RD_INTERVAL_PHY_REPEATER(dp_phy),
+				      caps, DP_LTTPR_PHY_CAP_SIZE);
 }
 EXPORT_SYMBOL(drm_dp_read_lttpr_phy_caps);
 
drivers/gpu/drm/i915/display/intel_dp_link_training.c +21 -9
index 5d98773efd1b3..fbee20a76cf44 100644
@@ -55,6 +55,7 @@ static u8 *intel_dp_lttpr_phy_caps(struct intel_dp *intel_dp,
 }
 
 static void intel_dp_read_lttpr_phy_caps(struct intel_dp *intel_dp,
+					 const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 					 enum drm_dp_phy dp_phy)
 {
 	struct intel_encoder *encoder = &dp_to_dig_port(intel_dp)->base;
@@ -63,7 +64,7 @@ static void intel_dp_read_lttpr_phy_caps(struct intel_dp *intel_dp,
 
 	intel_dp_phy_name(dp_phy, phy_name, sizeof(phy_name));
 
-	if (drm_dp_read_lttpr_phy_caps(&intel_dp->aux, dp_phy, phy_caps) < 0) {
+	if (drm_dp_read_lttpr_phy_caps(&intel_dp->aux, dpcd, dp_phy, phy_caps) < 0) {
 		drm_dbg_kms(&dp_to_i915(intel_dp)->drm,
 			    "[ENCODER:%d:%s][%s] failed to read the PHY caps\n",
 			    encoder->base.base.id, encoder->base.name, phy_name);
@@ -77,10 +78,11 @@ static void intel_dp_read_lttpr_phy_caps(struct intel_dp *intel_dp,
 		    phy_caps);
 }
 
-static bool intel_dp_read_lttpr_common_caps(struct intel_dp *intel_dp)
+static bool intel_dp_read_lttpr_common_caps(struct intel_dp *intel_dp, const u8 dpcd[DP_RECEIVER_CAP_SIZE])
 {
 	struct intel_encoder *encoder = &dp_to_dig_port(intel_dp)->base;
 	struct drm_i915_private *i915 = to_i915(encoder->base.dev);
+	int ret;
 
 	if (intel_dp_is_edp(intel_dp))
 		return false;
@@ -92,8 +94,9 @@ static bool intel_dp_read_lttpr_common_caps(struct intel_dp *intel_dp)
 	if (DISPLAY_VER(i915) < 10 || IS_GEMINILAKE(i915))
 		return false;
 
-	if (drm_dp_read_lttpr_common_caps(&intel_dp->aux,
-					  intel_dp->lttpr_common_caps) < 0)
+	ret = drm_dp_read_lttpr_common_caps(&intel_dp->aux, dpcd,
+					    intel_dp->lttpr_common_caps);
+	if (ret < 0)
 		goto reset_caps;
 
 	drm_dbg_kms(&dp_to_i915(intel_dp)->drm,
@@ -122,14 +125,14 @@ intel_dp_set_lttpr_transparent_mode(struct intel_dp *intel_dp, bool enable)
 	return drm_dp_dpcd_write(&intel_dp->aux, DP_PHY_REPEATER_MODE, &val, 1) == 1;
 }
 
-static int intel_dp_init_lttpr(struct intel_dp *intel_dp)
+static int intel_dp_init_lttpr(struct intel_dp *intel_dp, const u8 dpcd[DP_RECEIVER_CAP_SIZE])
 {
 	struct intel_encoder *encoder = &dp_to_dig_port(intel_dp)->base;
 	struct drm_i915_private *i915 = to_i915(encoder->base.dev);
 	int lttpr_count;
 	int i;
 
-	if (!intel_dp_read_lttpr_common_caps(intel_dp))
+	if (!intel_dp_read_lttpr_common_caps(intel_dp, dpcd))
 		return 0;
 
 	lttpr_count = drm_dp_lttpr_count(intel_dp->lttpr_common_caps);
@@ -168,7 +171,7 @@ static int intel_dp_init_lttpr(struct intel_dp *intel_dp)
 	}
 
 	for (i = 0; i < lttpr_count; i++)
-		intel_dp_read_lttpr_phy_caps(intel_dp, DP_PHY_LTTPR(i));
+		intel_dp_read_lttpr_phy_caps(intel_dp, dpcd, DP_PHY_LTTPR(i));
 
 	return lttpr_count;
 }
@@ -193,9 +196,18 @@ static int intel_dp_init_lttpr(struct intel_dp *intel_dp)
  */
 int intel_dp_init_lttpr_and_dprx_caps(struct intel_dp *intel_dp)
 {
-	int lttpr_count = intel_dp_init_lttpr(intel_dp);
+	u8 dpcd[DP_RECEIVER_CAP_SIZE];
+	int lttpr_count;
 
-	/* The DPTX shall read the DPRX caps after LTTPR detection. */
+	if (drm_dp_read_dpcd_caps(&intel_dp->aux, dpcd))
+		return -EIO;
+
+	lttpr_count = intel_dp_init_lttpr(intel_dp, dpcd);
+
+	/*
+	 * The DPTX shall read the DPRX caps after LTTPR detection, so re-read
+	 * it here.
+	 */
 	if (drm_dp_read_dpcd_caps(&intel_dp->aux, intel_dp->dpcd)) {
 		intel_dp_reset_lttpr_common_caps(intel_dp);
 		return -EIO;
include/drm/dp/drm_dp_helper.h +2 -0
index 51e02cf75277e..1eccd97419436 100644
@@ -2148,8 +2148,10 @@ bool drm_dp_read_sink_count_cap(struct drm_connector *connector,
 int drm_dp_read_sink_count(struct drm_dp_aux *aux);
 
 int drm_dp_read_lttpr_common_caps(struct drm_dp_aux *aux,
+				  const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 				  u8 caps[DP_LTTPR_COMMON_CAP_SIZE]);
 int drm_dp_read_lttpr_phy_caps(struct drm_dp_aux *aux,
+			       const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 			       enum drm_dp_phy dp_phy,
 			       u8 caps[DP_LTTPR_PHY_CAP_SIZE]);
 int drm_dp_lttpr_count(const u8 cap[DP_LTTPR_COMMON_CAP_SIZE]);
Signature · 1 line
2.30.2
Reviewed-by on v2 1/1
#7 lore raw
Quoted 32 lines · Imre Deak

At least some DELL monitors (P2715Q) with DPCD_REV 1.2 return corrupted DPCD register values when reading from the 0xF0000- LTTPR range with an AUX transaction block size bigger than 1. The DP standard requires 0 to be returned - as for any other reserved/invalid addresses - but these monitors return the DPCD_REV register value repeated in each byte of the read buffer. This will in turn corrupt the values returned by the LTTPRs between the source and the monitor: LTTPRs must adjust the values they read from the downstream DPRX, for instance left-shift/init the downstream DP_PHY_REPEATER_CNT value. Since the value returned by the monitor's DPRX is non-zero the adjusted values will be corrupt.

Reading the LTTPR registers one-by-one instead of reading all of them with a single AUX transfer works around the issue.

According to the DP standard's 0xF0000 register description:
"LTTPR-related registers at DPCD Addresses F0000h through F02FFh are valid only for DPCD r1.4 (or higher)." While it's unclear if DPCD r1.4 refers to the DPCD_REV or to the LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV register (tickets filed at the VESA site to clarify this haven't been addressed), one possibility is that it's a restriction due to non-compliant monitors described above. Disabling the non-transparent LTTPR mode for all such monitors is not a viable solution: the transparent LTTPR mode has its own issue causing link training failures and this would affect a lot of monitors in use with DPCD_REV < 1.4. Instead this patch works around the problem by reading the LTTPR common and PHY cap registers one-by-one for any monitor with a DPCD_REV < 1.4.

The standard requires the DPCD capabilites to be read after the LTTPR common capabilities are read, so re-read the DPCD capabilities after the LTTPR common and PHY caps were read out.

Quoted 7 lines

v2:
- Use for instead of a while loop. (Ville)
- Add to code comment the monitor model with the problem.

Quoted 212 lines
---
 drivers/gpu/drm/dp/drm_dp.c                   | 57 ++++++++++++-------
 .../drm/i915/display/intel_dp_link_training.c | 30 +++++++---
 include/drm/dp/drm_dp_helper.h                |  2 +
 3 files changed, 58 insertions(+), 31 deletions(-)
drivers/gpu/drm/dp/drm_dp.c +35 -22
index 703972ae14c64..58744f83931af 100644
@@ -2390,9 +2390,35 @@ int drm_dp_dsc_sink_supported_input_bpcs(const u8 dsc_dpcd[DP_DSC_RECEIVER_CAP_S
 }
 EXPORT_SYMBOL(drm_dp_dsc_sink_supported_input_bpcs);
 
+static int drm_dp_read_lttpr_regs(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], int address,
+				  u8 *buf, int buf_size)
+{
+	/*
+	 * At least the DELL P2715Q monitor with a DPCD_REV < 0x14 returns
+	 * corrupted values when reading from the 0xF0000- range with a block
+	 * size bigger than 1.
+	 */
+	int block_size = dpcd[DP_DPCD_REV] < 0x14 ? 1 : buf_size;
+	int offset;
+	int ret;
+
+	for (offset = 0; offset < buf_size; offset += block_size) {
+		ret = drm_dp_dpcd_read(aux,
+				       address + offset,
+				       &buf[offset], block_size);
+		if (ret < 0)
+			return ret;
+
+		WARN_ON(ret != block_size);
+	}
+
+	return 0;
+}
+
 /**
  * drm_dp_read_lttpr_common_caps - read the LTTPR common capabilities
  * @aux: DisplayPort AUX channel
+ * @dpcd: DisplayPort configuration data
  * @caps: buffer to return the capability info in
  *
  * Read capabilities common to all LTTPRs.
@@ -2400,25 +2426,19 @@ EXPORT_SYMBOL(drm_dp_dsc_sink_supported_input_bpcs);
  * Returns 0 on success or a negative error code on failure.
  */
 int drm_dp_read_lttpr_common_caps(struct drm_dp_aux *aux,
+				  const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 				  u8 caps[DP_LTTPR_COMMON_CAP_SIZE])
 {
-	int ret;
-
-	ret = drm_dp_dpcd_read(aux,
-			       DP_LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV,
-			       caps, DP_LTTPR_COMMON_CAP_SIZE);
-	if (ret < 0)
-		return ret;
-
-	WARN_ON(ret != DP_LTTPR_COMMON_CAP_SIZE);
-
-	return 0;
+	return drm_dp_read_lttpr_regs(aux, dpcd,
+				      DP_LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV,
+				      caps, DP_LTTPR_COMMON_CAP_SIZE);
 }
 EXPORT_SYMBOL(drm_dp_read_lttpr_common_caps);
 
 /**
  * drm_dp_read_lttpr_phy_caps - read the capabilities for a given LTTPR PHY
  * @aux: DisplayPort AUX channel
+ * @dpcd: DisplayPort configuration data
  * @dp_phy: LTTPR PHY to read the capabilities for
  * @caps: buffer to return the capability info in
  *
@@ -2427,20 +2447,13 @@ EXPORT_SYMBOL(drm_dp_read_lttpr_common_caps);
  * Returns 0 on success or a negative error code on failure.
  */
 int drm_dp_read_lttpr_phy_caps(struct drm_dp_aux *aux,
+			       const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 			       enum drm_dp_phy dp_phy,
 			       u8 caps[DP_LTTPR_PHY_CAP_SIZE])
 {
-	int ret;
-
-	ret = drm_dp_dpcd_read(aux,
-			       DP_TRAINING_AUX_RD_INTERVAL_PHY_REPEATER(dp_phy),
-			       caps, DP_LTTPR_PHY_CAP_SIZE);
-	if (ret < 0)
-		return ret;
-
-	WARN_ON(ret != DP_LTTPR_PHY_CAP_SIZE);
-
-	return 0;
+	return drm_dp_read_lttpr_regs(aux, dpcd,
+				      DP_TRAINING_AUX_RD_INTERVAL_PHY_REPEATER(dp_phy),
+				      caps, DP_LTTPR_PHY_CAP_SIZE);
 }
 EXPORT_SYMBOL(drm_dp_read_lttpr_phy_caps);
 
drivers/gpu/drm/i915/display/intel_dp_link_training.c +21 -9
index 5d98773efd1b3..fbee20a76cf44 100644
@@ -55,6 +55,7 @@ static u8 *intel_dp_lttpr_phy_caps(struct intel_dp *intel_dp,
 }
 
 static void intel_dp_read_lttpr_phy_caps(struct intel_dp *intel_dp,
+					 const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 					 enum drm_dp_phy dp_phy)
 {
 	struct intel_encoder *encoder = &dp_to_dig_port(intel_dp)->base;
@@ -63,7 +64,7 @@ static void intel_dp_read_lttpr_phy_caps(struct intel_dp *intel_dp,
 
 	intel_dp_phy_name(dp_phy, phy_name, sizeof(phy_name));
 
-	if (drm_dp_read_lttpr_phy_caps(&intel_dp->aux, dp_phy, phy_caps) < 0) {
+	if (drm_dp_read_lttpr_phy_caps(&intel_dp->aux, dpcd, dp_phy, phy_caps) < 0) {
 		drm_dbg_kms(&dp_to_i915(intel_dp)->drm,
 			    "[ENCODER:%d:%s][%s] failed to read the PHY caps\n",
 			    encoder->base.base.id, encoder->base.name, phy_name);
@@ -77,10 +78,11 @@ static void intel_dp_read_lttpr_phy_caps(struct intel_dp *intel_dp,
 		    phy_caps);
 }
 
-static bool intel_dp_read_lttpr_common_caps(struct intel_dp *intel_dp)
+static bool intel_dp_read_lttpr_common_caps(struct intel_dp *intel_dp, const u8 dpcd[DP_RECEIVER_CAP_SIZE])
 {
 	struct intel_encoder *encoder = &dp_to_dig_port(intel_dp)->base;
 	struct drm_i915_private *i915 = to_i915(encoder->base.dev);
+	int ret;
 
 	if (intel_dp_is_edp(intel_dp))
 		return false;
@@ -92,8 +94,9 @@ static bool intel_dp_read_lttpr_common_caps(struct intel_dp *intel_dp)
 	if (DISPLAY_VER(i915) < 10 || IS_GEMINILAKE(i915))
 		return false;
 
-	if (drm_dp_read_lttpr_common_caps(&intel_dp->aux,
-					  intel_dp->lttpr_common_caps) < 0)
+	ret = drm_dp_read_lttpr_common_caps(&intel_dp->aux, dpcd,
+					    intel_dp->lttpr_common_caps);
+	if (ret < 0)
 		goto reset_caps;
 
 	drm_dbg_kms(&dp_to_i915(intel_dp)->drm,
@@ -122,14 +125,14 @@ intel_dp_set_lttpr_transparent_mode(struct intel_dp *intel_dp, bool enable)
 	return drm_dp_dpcd_write(&intel_dp->aux, DP_PHY_REPEATER_MODE, &val, 1) == 1;
 }
 
-static int intel_dp_init_lttpr(struct intel_dp *intel_dp)
+static int intel_dp_init_lttpr(struct intel_dp *intel_dp, const u8 dpcd[DP_RECEIVER_CAP_SIZE])
 {
 	struct intel_encoder *encoder = &dp_to_dig_port(intel_dp)->base;
 	struct drm_i915_private *i915 = to_i915(encoder->base.dev);
 	int lttpr_count;
 	int i;
 
-	if (!intel_dp_read_lttpr_common_caps(intel_dp))
+	if (!intel_dp_read_lttpr_common_caps(intel_dp, dpcd))
 		return 0;
 
 	lttpr_count = drm_dp_lttpr_count(intel_dp->lttpr_common_caps);
@@ -168,7 +171,7 @@ static int intel_dp_init_lttpr(struct intel_dp *intel_dp)
 	}
 
 	for (i = 0; i < lttpr_count; i++)
-		intel_dp_read_lttpr_phy_caps(intel_dp, DP_PHY_LTTPR(i));
+		intel_dp_read_lttpr_phy_caps(intel_dp, dpcd, DP_PHY_LTTPR(i));
 
 	return lttpr_count;
 }
@@ -193,9 +196,18 @@ static int intel_dp_init_lttpr(struct intel_dp *intel_dp)
  */
 int intel_dp_init_lttpr_and_dprx_caps(struct intel_dp *intel_dp)
 {
-	int lttpr_count = intel_dp_init_lttpr(intel_dp);
+	u8 dpcd[DP_RECEIVER_CAP_SIZE];
+	int lttpr_count;
 
-	/* The DPTX shall read the DPRX caps after LTTPR detection. */
+	if (drm_dp_read_dpcd_caps(&intel_dp->aux, dpcd))
+		return -EIO;
+
+	lttpr_count = intel_dp_init_lttpr(intel_dp, dpcd);
+
+	/*
+	 * The DPTX shall read the DPRX caps after LTTPR detection, so re-read
+	 * it here.
+	 */
 	if (drm_dp_read_dpcd_caps(&intel_dp->aux, intel_dp->dpcd)) {
 		intel_dp_reset_lttpr_common_caps(intel_dp);
 		return -EIO;
include/drm/dp/drm_dp_helper.h +2 -0
index 51e02cf75277e..1eccd97419436 100644
@@ -2148,8 +2148,10 @@ bool drm_dp_read_sink_count_cap(struct drm_connector *connector,
 int drm_dp_read_sink_count(struct drm_dp_aux *aux);
 
 int drm_dp_read_lttpr_common_caps(struct drm_dp_aux *aux,
+				  const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 				  u8 caps[DP_LTTPR_COMMON_CAP_SIZE]);
 int drm_dp_read_lttpr_phy_caps(struct drm_dp_aux *aux,
+			       const u8 dpcd[DP_RECEIVER_CAP_SIZE],
 			       enum drm_dp_phy dp_phy,
 			       u8 caps[DP_LTTPR_PHY_CAP_SIZE]);
 int drm_dp_lttpr_count(const u8 cap[DP_LTTPR_COMMON_CAP_SIZE]);
Signature · 1 line
2.30.2
Signature · 2 lines
Ville Syrjälä
Intel
#8 lore raw

[Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities (rev2)

In reply to Imre Deak
== Series Details ==

== Series Details ==

Series: drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities (rev2)
URL : https://patchwork.freedesktop.org/series/100851/
State : warning

== Summary ==

$ dim checkpatch origin/drm-tip
8d7fe49b240d drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities
-:38: WARNING:TYPO_SPELLING: 'capabilites' may be misspelled - perhaps 'capabilities'?
#38: 
The standard requires the DPCD capabilites to be read after the LTTPR
                               ^^^^^^^^^^^

-:58: WARNING:LONG_LINE: line length of 107 exceeds 100 columns
#58: FILE: drivers/gpu/drm/dp/drm_dp.c:2393:
+static int drm_dp_read_lttpr_regs(struct drm_dp_aux *aux, const u8 dpcd[DP_RECEIVER_CAP_SIZE], int address,

-:172: WARNING:LONG_LINE: line length of 107 exceeds 100 columns
#172: FILE: drivers/gpu/drm/i915/display/intel_dp_link_training.c:81:
+static bool intel_dp_read_lttpr_common_caps(struct intel_dp *intel_dp, const u8 dpcd[DP_RECEIVER_CAP_SIZE])

total: 0 errors, 3 warnings, 0 checks, 181 lines checked

#9 lore raw

[Intel-gfx] ✗ Fi.CI.DOCS: warning for drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities (rev2)

In reply to Imre Deak
== Series Details ==

== Series Details ==

Series: drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities (rev2)
URL : https://patchwork.freedesktop.org/series/100851/
State : warning

== Summary ==

$ make htmldocs 2>&1 > /dev/null | grep i915
./drivers/gpu/drm/i915/display/intel_drrs.c:1: warning: 'intel_drrs_enable' not found
./drivers/gpu/drm/i915/display/intel_drrs.c:1: warning: 'intel_drrs_disable' not found
#10 lore raw

[Intel-gfx] ✓ Fi.CI.BAT: success for drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities (rev2)

In reply to Imre Deak
== Series Details ==

== Series Details ==

Series: drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities (rev2)
URL : https://patchwork.freedesktop.org/series/100851/
State : success

== Summary ==

CI Bug Log - changes from CI_DRM_11396 -> Patchwork_22643
====================================================

Summary
-------

**SUCCESS**

No regressions found.

External URL: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/index.html

Participating hosts (49 -> 43)
------------------------------

Missing (6): shard-tglu fi-hsw-4200u fi-bsw-cyan fi-ctg-p8600 shard-rkl fi-bdw-samus

Possible new issues
-------------------

Here are the unknown changes that may have been introduced in Patchwork_22643:

### IGT changes ###

#### Suppressed ####

The following results come from untrusted machines, tests, or statuses. They do not affect the overall result.

* igt@i915_selftest@live@requests:
- {bat-adlm-1}: NOTRUN -> [INCOMPLETE][1]
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/bat-adlm-1/igt@i915_selftest@[email protected]

Known issues
------------

Here are the changes found in Patchwork_22643 that come from known issues:

### IGT changes ###

#### Issues hit ####

* igt@gem_exec_suspend@basic-s0@smem:
- fi-glk-dsi: [PASS][2] -> [DMESG-WARN][3] ([i915#2943])
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/fi-glk-dsi/igt@gem_exec_suspend@[email protected]
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/fi-glk-dsi/igt@gem_exec_suspend@[email protected]

#### Possible fixes ####

* igt@i915_selftest@live@evict:
- {bat-rpls-2}: [INCOMPLETE][4] -> [PASS][5]
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/bat-rpls-2/igt@i915_selftest@[email protected]
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/bat-rpls-2/igt@i915_selftest@[email protected]

* igt@i915_selftest@live@objects:
- {bat-rpls-2}: [DMESG-WARN][6] ([i915#4391]) -> [PASS][7] +4 similar issues
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/bat-rpls-2/igt@i915_selftest@[email protected]
[7]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/bat-rpls-2/igt@i915_selftest@[email protected]

* igt@kms_force_connector_basic@force-connector-state:
- {bat-adlm-1}: [INCOMPLETE][8] ([i915#5361]) -> [PASS][9]
[8]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/bat-adlm-1/igt@[email protected]
[9]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/bat-adlm-1/igt@[email protected]

* igt@kms_pipe_crc_basic@compare-crc-sanitycheck-pipe-c:
- fi-cfl-8109u: [DMESG-WARN][10] ([i915#295] / [i915#5341]) -> [PASS][11]
[10]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/fi-cfl-8109u/igt@[email protected]
[11]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/fi-cfl-8109u/igt@[email protected]

* igt@kms_pipe_crc_basic@read-crc-pipe-b:
- fi-cfl-8109u: [DMESG-WARN][12] ([i915#295]) -> [PASS][13] +10 similar issues
[12]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/fi-cfl-8109u/igt@[email protected]
[13]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/fi-cfl-8109u/igt@[email protected]

{name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).

[fdo#109285]: https://bugs.freedesktop.org/show_bug.cgi?id=109285
[i915#1072]: https://gitlab.freedesktop.org/drm/intel/issues/1072
[i915#1155]: https://gitlab.freedesktop.org/drm/intel/issues/1155
[i915#2943]: https://gitlab.freedesktop.org/drm/intel/issues/2943
[i915#295]: https://gitlab.freedesktop.org/drm/intel/issues/295
[i915#3555]: https://gitlab.freedesktop.org/drm/intel/issues/3555
[i915#3708]: https://gitlab.freedesktop.org/drm/intel/issues/3708
[i915#4312]: https://gitlab.freedesktop.org/drm/intel/issues/4312
[i915#4391]: https://gitlab.freedesktop.org/drm/intel/issues/4391
[i915#5195]: https://gitlab.freedesktop.org/drm/intel/issues/5195
[i915#5341]: https://gitlab.freedesktop.org/drm/intel/issues/5341
[i915#5361]: https://gitlab.freedesktop.org/drm/intel/issues/5361

Build changes
-------------

* Linux: CI_DRM_11396 -> Patchwork_22643

CI-20190529: 20190529
CI_DRM_11396: 18b88414e6c9660022bb464d4d5fadb07d38cf04 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_6387: 04d012b18355b53798af5a55a8915afb1a421bba @ https://gitlab.freedesktop.org/drm/igt-gpu-tools.git
Patchwork_22643: 8d7fe49b240d8f4fb1a167594706ab916e4a78cb @ git://anongit.freedesktop.org/gfx-ci/linux

== Linux commits ==

8d7fe49b240d drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/index.html

#11 lore raw

[Intel-gfx] ✓ Fi.CI.IGT: success for drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities (rev2)

In reply to Imre Deak
== Series Details ==

== Series Details ==

Series: drm/i915: Add a DP1.2 compatible way to read LTTPR capabilities (rev2)
URL : https://patchwork.freedesktop.org/series/100851/
State : success

== Summary ==

CI Bug Log - changes from CI_DRM_11396_full -> Patchwork_22643_full
====================================================

Summary
-------

**SUCCESS**

No regressions found.

Participating hosts (12 -> 12)
------------------------------

No changes in participating hosts

Possible new issues
-------------------

Here are the unknown changes that may have been introduced in Patchwork_22643_full:

### IGT changes ###

#### Suppressed ####

The following results come from untrusted machines, tests, or statuses. They do not affect the overall result.

* igt@gem_softpin@overlap:
- {shard-rkl}: [PASS][1] -> [INCOMPLETE][2]
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-5/igt@[email protected]
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-5/igt@[email protected]

* igt@kms_cursor_crc@pipe-b-cursor-128x42-random:
- {shard-rkl}: [SKIP][3] ([fdo#112022] / [i915#4070]) -> [INCOMPLETE][4]
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-2/igt@[email protected]
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-5/igt@[email protected]

Known issues
------------

Here are the changes found in Patchwork_22643_full that come from known issues:

### IGT changes ###

#### Issues hit ####

* igt@gem_eio@in-flight-contexts-1us:
- shard-iclb: [PASS][5] -> [TIMEOUT][6] ([i915#3070])
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-iclb2/igt@[email protected]
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-iclb4/igt@[email protected]

* igt@gem_eio@in-flight-contexts-immediate:
- shard-skl: [PASS][7] -> [TIMEOUT][8] ([i915#3063])
[7]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-skl8/igt@[email protected]
[8]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl5/igt@[email protected]

* igt@gem_exec_balancer@parallel-balancer:
- shard-iclb: [PASS][9] -> [SKIP][10] ([i915#4525])
[9]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-iclb4/igt@[email protected]
[10]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-iclb6/igt@[email protected]

* igt@gem_exec_balancer@parallel-ordering:
- shard-kbl: NOTRUN -> [DMESG-FAIL][11] ([i915#5076])
[11]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl6/igt@[email protected]

* igt@gem_exec_capture@pi@vcs0:
- shard-skl: NOTRUN -> [INCOMPLETE][12] ([i915#4547])
[12]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl1/igt@gem_exec_capture@[email protected]

* igt@gem_exec_fair@basic-none@rcs0:
- shard-kbl: [PASS][13] -> [FAIL][14] ([i915#2842]) +2 similar issues
[13]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-kbl1/igt@gem_exec_fair@[email protected]
[14]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl7/igt@gem_exec_fair@[email protected]

* igt@gem_exec_fair@basic-pace-solo@rcs0:
- shard-kbl: NOTRUN -> [FAIL][15] ([i915#2842])
[15]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl6/igt@gem_exec_fair@[email protected]

* igt@gem_exec_fair@basic-pace@rcs0:
- shard-glk: [PASS][16] -> [FAIL][17] ([i915#2842])
[16]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-glk5/igt@gem_exec_fair@[email protected]
[17]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-glk5/igt@gem_exec_fair@[email protected]

* igt@gem_exec_whisper@basic-fds-priority-all:
- shard-apl: [PASS][18] -> [INCOMPLETE][19] ([i915#5268])
[18]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-apl4/igt@[email protected]
[19]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl2/igt@[email protected]

* igt@gem_lmem_swapping@heavy-verify-random:
- shard-kbl: NOTRUN -> [SKIP][20] ([fdo#109271] / [i915#4613]) +2 similar issues
[20]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl6/igt@[email protected]

* igt@gem_lmem_swapping@parallel-random-engines:
- shard-skl: NOTRUN -> [SKIP][21] ([fdo#109271] / [i915#4613]) +1 similar issue
[21]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl6/igt@[email protected]

* igt@gem_pxp@verify-pxp-execution-after-suspend-resume:
- shard-apl: NOTRUN -> [SKIP][22] ([fdo#109271]) +61 similar issues
[22]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl1/igt@[email protected]

* igt@gem_userptr_blits@dmabuf-sync:
- shard-apl: NOTRUN -> [SKIP][23] ([fdo#109271] / [i915#3323])
[23]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl4/igt@[email protected]

* igt@kms_big_fb@4-tiled-8bpp-rotate-90:
- shard-kbl: NOTRUN -> [SKIP][24] ([fdo#109271]) +215 similar issues
[24]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl6/igt@[email protected]

* igt@kms_big_fb@linear-32bpp-rotate-0:
- shard-glk: [PASS][25] -> [DMESG-WARN][26] ([i915#118])
[25]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-glk3/igt@[email protected]
[26]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-glk9/igt@[email protected]

* igt@kms_big_fb@x-tiled-max-hw-stride-32bpp-rotate-0-hflip:
- shard-kbl: NOTRUN -> [SKIP][27] ([fdo#109271] / [i915#3777]) +1 similar issue
[27]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl6/igt@[email protected]

* igt@kms_big_fb@x-tiled-max-hw-stride-64bpp-rotate-180-async-flip:
- shard-skl: NOTRUN -> [FAIL][28] ([i915#3743]) +1 similar issue
[28]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl10/igt@kms_big_fb@x-tiled-max-hw-stride-64bpp-rotate-180-async-flip.html

* igt@kms_big_fb@y-tiled-max-hw-stride-64bpp-rotate-0-async-flip:
- shard-skl: NOTRUN -> [FAIL][29] ([i915#3763])
[29]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl6/igt@[email protected]

* igt@kms_big_fb@yf-tiled-max-hw-stride-32bpp-rotate-0-hflip:
- shard-apl: NOTRUN -> [SKIP][30] ([fdo#109271] / [i915#3777]) +1 similar issue
[30]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl1/igt@[email protected]

* igt@kms_ccs@pipe-b-ccs-on-another-bo-y_tiled_gen12_mc_ccs:
- shard-apl: NOTRUN -> [SKIP][31] ([fdo#109271] / [i915#3886]) +1 similar issue
[31]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl1/igt@kms_ccs@pipe-b-ccs-on-another-bo-y_tiled_gen12_mc_ccs.html

* igt@kms_ccs@pipe-b-crc-primary-rotation-180-y_tiled_gen12_mc_ccs:
- shard-kbl: NOTRUN -> [SKIP][32] ([fdo#109271] / [i915#3886]) +6 similar issues
[32]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl7/igt@kms_ccs@pipe-b-crc-primary-rotation-180-y_tiled_gen12_mc_ccs.html

* igt@kms_ccs@pipe-b-crc-primary-rotation-180-y_tiled_gen12_rc_ccs_cc:
- shard-skl: NOTRUN -> [SKIP][33] ([fdo#109271] / [i915#3886]) +4 similar issues
[33]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl6/igt@kms_ccs@pipe-b-crc-primary-rotation-180-y_tiled_gen12_rc_ccs_cc.html

* igt@kms_chamelium@hdmi-hpd-for-each-pipe:
- shard-kbl: NOTRUN -> [SKIP][34] ([fdo#109271] / [fdo#111827]) +18 similar issues
[34]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl1/igt@[email protected]

* igt@kms_chamelium@vga-frame-dump:
- shard-skl: NOTRUN -> [SKIP][35] ([fdo#109271] / [fdo#111827]) +9 similar issues
[35]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl6/igt@[email protected]

* igt@kms_color_chamelium@pipe-b-gamma:
- shard-apl: NOTRUN -> [SKIP][36] ([fdo#109271] / [fdo#111827]) +5 similar issues
[36]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl1/igt@[email protected]

* igt@kms_content_protection@atomic-dpms:
- shard-kbl: NOTRUN -> [TIMEOUT][37] ([i915#1319])
[37]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl7/igt@[email protected]

* igt@kms_content_protection@lic:
- shard-apl: NOTRUN -> [TIMEOUT][38] ([i915#1319])
[38]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl2/igt@[email protected]

* igt@kms_cursor_legacy@pipe-d-single-bo:
- shard-skl: NOTRUN -> [SKIP][39] ([fdo#109271] / [i915#533]) +1 similar issue
[39]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl10/igt@[email protected]

* igt@kms_dp_tiled_display@basic-test-pattern-with-chamelium:
- shard-glk: NOTRUN -> [SKIP][40] ([fdo#109271])
[40]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-glk1/igt@[email protected]

* igt@kms_flip@flip-vs-expired-vblank@a-edp1:
- shard-skl: NOTRUN -> [FAIL][41] ([i915#79]) +1 similar issue
[41]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl6/igt@kms_flip@[email protected]

* igt@kms_flip@flip-vs-suspend-interruptible@a-dp1:
- shard-kbl: [PASS][42] -> [DMESG-WARN][43] ([i915#180]) +5 similar issues
[42]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-kbl3/igt@kms_flip@[email protected]
[43]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl4/igt@kms_flip@[email protected]

* igt@kms_flip_scaled_crc@flip-32bpp-ytile-to-32bpp-ytileccs-downscaling:
- shard-skl: NOTRUN -> [INCOMPLETE][44] ([i915#3701])
[44]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl6/igt@kms_flip_scaled_crc@flip-32bpp-ytile-to-32bpp-ytileccs-downscaling.html
- shard-iclb: [PASS][45] -> [SKIP][46] ([i915#3701])
[45]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-iclb1/igt@kms_flip_scaled_crc@flip-32bpp-ytile-to-32bpp-ytileccs-downscaling.html
[46]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-iclb2/igt@kms_flip_scaled_crc@flip-32bpp-ytile-to-32bpp-ytileccs-downscaling.html

* igt@kms_frontbuffer_tracking@fbc-farfromfence-mmap-gtt:
- shard-skl: NOTRUN -> [SKIP][47] ([fdo#109271]) +111 similar issues
[47]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl6/igt@[email protected]

* igt@kms_hdr@bpc-switch-suspend@bpc-switch-suspend-edp-1-pipe-a:
- shard-skl: NOTRUN -> [FAIL][48] ([i915#1188])
[48]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl6/igt@kms_hdr@[email protected]

* igt@kms_pipe_crc_basic@suspend-read-crc-pipe-c:
- shard-apl: [PASS][49] -> [DMESG-WARN][50] ([i915#180]) +1 similar issue
[49]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-apl4/igt@[email protected]
[50]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl3/igt@[email protected]

* igt@kms_plane_alpha_blend@pipe-b-alpha-opaque-fb:
- shard-skl: NOTRUN -> [FAIL][51] ([fdo#108145] / [i915#265]) +2 similar issues
[51]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl6/igt@[email protected]

* igt@kms_plane_alpha_blend@pipe-c-alpha-7efc:
- shard-kbl: NOTRUN -> [FAIL][52] ([fdo#108145] / [i915#265]) +2 similar issues
[52]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl7/igt@[email protected]

* igt@kms_plane_alpha_blend@pipe-c-alpha-transparent-fb:
- shard-kbl: NOTRUN -> [FAIL][53] ([i915#265])
[53]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl1/igt@[email protected]

* igt@kms_plane_alpha_blend@pipe-c-constant-alpha-max:
- shard-apl: NOTRUN -> [FAIL][54] ([fdo#108145] / [i915#265])
[54]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl4/igt@[email protected]

* igt@kms_plane_alpha_blend@pipe-c-coverage-7efc:
- shard-skl: [PASS][55] -> [FAIL][56] ([fdo#108145] / [i915#265]) +1 similar issue
[55]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-skl5/igt@[email protected]
[56]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl4/igt@[email protected]

* igt@kms_plane_scaling@planes-upscale-20x20-downscale-factor-0-5@pipe-a-edp-1-planes-upscale-downscale:
- shard-iclb: [PASS][57] -> [SKIP][58] ([i915#5235]) +2 similar issues
[57]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-iclb1/igt@kms_plane_scaling@planes-upscale-20x20-downscale-factor-0-5@pipe-a-edp-1-planes-upscale-downscale.html
[58]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-iclb2/igt@kms_plane_scaling@planes-upscale-20x20-downscale-factor-0-5@pipe-a-edp-1-planes-upscale-downscale.html

* igt@kms_psr2_sf@overlay-plane-update-continuous-sf:
- shard-kbl: NOTRUN -> [SKIP][59] ([fdo#109271] / [i915#658])
[59]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl1/igt@[email protected]

* igt@kms_psr2_sf@overlay-plane-update-sf-dmg-area:
- shard-skl: NOTRUN -> [SKIP][60] ([fdo#109271] / [i915#658]) +1 similar issue
[60]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl6/igt@[email protected]

* igt@kms_psr2_su@frontbuffer-xrgb8888:
- shard-iclb: [PASS][61] -> [SKIP][62] ([fdo#109642] / [fdo#111068] / [i915#658])
[61]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-iclb2/igt@[email protected]
[62]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-iclb8/igt@[email protected]

* igt@kms_psr2_su@page_flip-p010:
- shard-apl: NOTRUN -> [SKIP][63] ([fdo#109271] / [i915#658])
[63]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl1/igt@kms_psr2_su@page_flip-p010.html

* igt@kms_psr@psr2_primary_mmap_cpu:
- shard-iclb: [PASS][64] -> [SKIP][65] ([fdo#109441]) +2 similar issues
[64]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-iclb2/igt@kms_psr@psr2_primary_mmap_cpu.html
[65]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-iclb4/igt@kms_psr@psr2_primary_mmap_cpu.html

* igt@kms_sysfs_edid_timing:
- shard-apl: NOTRUN -> [FAIL][66] ([IGT#2])
[66]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl1/igt@kms_sysfs_edid_timing.html

* igt@kms_vblank@pipe-d-wait-idle:
- shard-kbl: NOTRUN -> [SKIP][67] ([fdo#109271] / [i915#533]) +2 similar issues
[67]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl7/igt@[email protected]

* igt@kms_writeback@writeback-pixel-formats:
- shard-skl: NOTRUN -> [SKIP][68] ([fdo#109271] / [i915#2437])
[68]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl10/igt@[email protected]

* igt@perf@polling-parameterized:
- shard-skl: [PASS][69] -> [FAIL][70] ([i915#1542])
[69]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-skl7/igt@[email protected]
[70]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl1/igt@[email protected]

* igt@sysfs_clients@recycle-many:
- shard-skl: NOTRUN -> [SKIP][71] ([fdo#109271] / [i915#2994])
[71]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl10/igt@[email protected]

* igt@sysfs_clients@sema-10:
- shard-apl: NOTRUN -> [SKIP][72] ([fdo#109271] / [i915#2994]) +1 similar issue
[72]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl2/igt@[email protected]

* igt@sysfs_clients@sema-50:
- shard-kbl: NOTRUN -> [SKIP][73] ([fdo#109271] / [i915#2994]) +1 similar issue
[73]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl6/igt@[email protected]

* igt@sysfs_timeslice_duration@timeout@vecs0:
- shard-apl: [PASS][74] -> [FAIL][75] ([i915#1755])
[74]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-apl3/igt@sysfs_timeslice_duration@[email protected]
[75]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl6/igt@sysfs_timeslice_duration@[email protected]

#### Possible fixes ####

* igt@fbdev@eof:
- {shard-rkl}: [SKIP][76] ([i915#2582]) -> [PASS][77]
[76]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-5/igt@[email protected]
[77]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@gem_ctx_persistence@many-contexts:
- {shard-rkl}: [FAIL][78] ([i915#2410]) -> [PASS][79]
[78]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-2/igt@[email protected]
[79]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-5/igt@[email protected]

* igt@gem_exec_capture@pi@bcs0:
- shard-skl: [INCOMPLETE][80] ([i915#4547]) -> [PASS][81]
[80]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-skl4/igt@gem_exec_capture@[email protected]
[81]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl1/igt@gem_exec_capture@[email protected]

* igt@gem_exec_fair@basic-pace-share@rcs0:
- shard-apl: [FAIL][82] ([i915#2842]) -> [PASS][83]
[82]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-apl1/igt@gem_exec_fair@[email protected]
[83]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl2/igt@gem_exec_fair@[email protected]

* igt@gem_exec_fair@basic-throttle@rcs0:
- shard-iclb: [FAIL][84] ([i915#2849]) -> [PASS][85]
[84]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-iclb1/igt@gem_exec_fair@[email protected]
[85]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-iclb3/igt@gem_exec_fair@[email protected]

* igt@gem_exec_nop@basic-series:
- shard-glk: [DMESG-WARN][86] ([i915#118]) -> [PASS][87]
[86]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-glk1/igt@[email protected]
[87]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-glk4/igt@[email protected]

* igt@gem_exec_whisper@basic-fds-forked-all:
- shard-glk: [DMESG-FAIL][88] -> [PASS][89]
[88]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-glk7/igt@[email protected]
[89]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-glk1/igt@[email protected]

* igt@i915_pm_dc@dc6-psr:
- shard-iclb: [FAIL][90] ([i915#454]) -> [PASS][91]
[90]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-iclb4/igt@[email protected]
[91]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-iclb7/igt@[email protected]

* igt@i915_pm_rpm@basic-pci-d3-state:
- {shard-rkl}: [SKIP][92] ([fdo#109308]) -> [PASS][93]
[92]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-1/igt@[email protected]
[93]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@i915_pm_rpm@modeset-lpsp:
- {shard-rkl}: [SKIP][94] ([i915#1397]) -> [PASS][95]
[94]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-1/igt@[email protected]
[95]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@kms_color@pipe-a-ctm-0-5:
- {shard-rkl}: [SKIP][96] ([i915#1149] / [i915#1849] / [i915#4070] / [i915#4098]) -> [PASS][97]
[96]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-2/igt@[email protected]
[97]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@kms_color@pipe-b-gamma:
- {shard-rkl}: [SKIP][98] ([i915#1149] / [i915#1849] / [i915#4098]) -> [PASS][99]
[98]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-5/igt@[email protected]
[99]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@kms_color@pipe-c-invalid-gamma-lut-sizes:
- {shard-rkl}: [SKIP][100] ([i915#4070]) -> [PASS][101]
[100]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-6/igt@[email protected]
[101]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-5/igt@[email protected]

* igt@kms_cursor_crc@pipe-a-cursor-suspend:
- shard-kbl: [DMESG-WARN][102] ([i915#180]) -> [PASS][103] +4 similar issues
[102]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-kbl4/igt@[email protected]
[103]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl7/igt@[email protected]

* igt@kms_cursor_crc@pipe-b-cursor-256x256-sliding:
- {shard-rkl}: [SKIP][104] ([fdo#112022]) -> [PASS][105]
[104]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-5/igt@[email protected]
[105]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@kms_cursor_crc@pipe-b-cursor-64x21-random:
- {shard-rkl}: [SKIP][106] ([fdo#112022] / [i915#4070]) -> [PASS][107] +8 similar issues
[106]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-1/igt@[email protected]
[107]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@kms_cursor_crc@pipe-c-cursor-suspend:
- shard-apl: [DMESG-WARN][108] ([i915#180]) -> [PASS][109] +1 similar issue
[108]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-apl8/igt@[email protected]
[109]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-apl4/igt@[email protected]

* igt@kms_cursor_edge_walk@pipe-a-256x256-right-edge:
- {shard-rkl}: [SKIP][110] ([i915#1849] / [i915#4070] / [i915#4098]) -> [PASS][111] +3 similar issues
[110]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-2/igt@[email protected]
[111]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@kms_cursor_legacy@flip-vs-cursor-busy-crc-atomic:
- {shard-rkl}: [SKIP][112] ([fdo#111825] / [i915#4070]) -> [PASS][113] +2 similar issues
[112]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-2/igt@[email protected]
[113]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@kms_draw_crc@draw-method-xrgb2101010-mmap-cpu-ytiled:
- {shard-rkl}: [SKIP][114] ([fdo#111314] / [i915#4098] / [i915#4369]) -> [PASS][115] +5 similar issues
[114]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-5/igt@[email protected]
[115]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@kms_fbcon_fbt@fbc-suspend:
- shard-kbl: [INCOMPLETE][116] ([i915#180] / [i915#636]) -> [PASS][117]
[116]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-kbl4/igt@[email protected]
[117]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-kbl6/igt@[email protected]

* igt@kms_flip@2x-plain-flip-fb-recreate@ab-hdmi-a1-hdmi-a2:
- shard-glk: [FAIL][118] ([i915#2122]) -> [PASS][119]
[118]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-glk2/igt@kms_flip@[email protected]
[119]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-glk4/igt@kms_flip@[email protected]

* igt@kms_flip@plain-flip-fb-recreate-interruptible@b-edp1:
- shard-skl: [FAIL][120] ([i915#2122]) -> [PASS][121]
[120]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-skl2/igt@kms_flip@[email protected]
[121]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl4/igt@kms_flip@[email protected]

* igt@kms_frontbuffer_tracking@fbcpsr-1p-primscrn-pri-shrfb-draw-render:
- {shard-rkl}: [SKIP][122] ([i915#1849]) -> [PASS][123] +24 similar issues
[122]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-2/igt@kms_frontbuffer_tracking@fbcpsr-1p-primscrn-pri-shrfb-draw-render.html
[123]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@kms_frontbuffer_tracking@fbcpsr-1p-primscrn-pri-shrfb-draw-render.html

* igt@kms_hdr@bpc-switch-dpms@bpc-switch-dpms-edp-1-pipe-a:
- shard-skl: [FAIL][124] ([i915#1188]) -> [PASS][125]
[124]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-skl10/igt@kms_hdr@[email protected]
[125]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-skl7/igt@kms_hdr@[email protected]

* igt@kms_invalid_mode@bad-vsync-end:
- {shard-rkl}: [SKIP][126] ([i915#4278]) -> [PASS][127]
[126]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-1/igt@[email protected]
[127]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@kms_pipe_crc_basic@suspend-read-crc-pipe-a:
- {shard-rkl}: [SKIP][128] ([i915#1849] / [i915#4098]) -> [PASS][129] +2 similar issues
[128]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-1/igt@[email protected]
[129]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@kms_plane@plane-panning-bottom-right@pipe-b-planes:
- {shard-rkl}: [SKIP][130] ([i915#3558]) -> [PASS][131] +1 similar issue
[130]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-1/igt@kms_plane@[email protected]
[131]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@kms_plane@[email protected]

* igt@kms_plane_multiple@atomic-pipe-b-tiling-y:
- {shard-rkl}: [SKIP][132] ([i915#3558] / [i915#4070]) -> [PASS][133]
[132]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-1/igt@[email protected]
[133]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@[email protected]

* igt@kms_plane_scaling@planes-downscale-factor-0-5@pipe-a-edp-1-planes-downscale:
- shard-iclb: [SKIP][134] ([i915#5235]) -> [PASS][135] +2 similar issues
[134]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-iclb2/igt@kms_plane_scaling@[email protected]
[135]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-iclb3/igt@kms_plane_scaling@[email protected]

* igt@kms_plane_scaling@scaler-with-clipping-clamping@pipe-b-edp-1-scaler-with-clipping-clamping:
- shard-iclb: [SKIP][136] ([i915#5176]) -> [PASS][137] +1 similar issue
[136]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-iclb3/igt@kms_plane_scaling@scaler-with-clipping-clamping@pipe-b-edp-1-scaler-with-clipping-clamping.html
[137]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-iclb5/igt@kms_plane_scaling@scaler-with-clipping-clamping@pipe-b-edp-1-scaler-with-clipping-clamping.html

* igt@kms_psr@cursor_render:
- {shard-rkl}: [SKIP][138] ([i915#1072]) -> [PASS][139] +1 similar issue
[138]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-rkl-5/igt@kms_psr@cursor_render.html
[139]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/shard-rkl-6/igt@kms_psr@cursor_render.html

* igt@kms_psr@psr2_cursor_plane_move:
- shard-iclb: [SKIP][140] ([fdo#109441]) -> [PASS][141] +2 similar issues
[140]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_11396/shard-iclb1/igt@kms_psr@psr

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_22643/index.html