ip/batadv: allow to specify RA when creating link
Subsystems (3)
PATCH 1/1 ip/batadv: allow to specify RA when creating link
This patch adds the possibility to specify batadv specific options when creating a new batman link. The only option available on link creation is IFLA_BATADV_ALGO_NAME which specifies the routing algorithm. Note there is no batadv specific attr to be handled on link dump.
Signed-off-by Nicolas Escande <[email protected]>
--- include/uapi/linux/batman_adv.h | 704 ++++++++++++++++++++++++++++++++ ip/Makefile | 2 +- ip/iplink_batadv.c | 64 +++ 3 files changed, 769 insertions(+), 1 deletion(-) create mode 100644 include/uapi/linux/batman_adv.h create mode 100644 ip/iplink_batadv.c
include/uapi/linux/batman_adv.h new file +704 -0
@@ -0,0 +1,704 @@ +/* SPDX-License-Identifier: MIT */ +/* Copyright (C) B.A.T.M.A.N. contributors: +* +* Matthias Schiffer +*/ + +#ifndef _UAPI_LINUX_BATMAN_ADV_H_ +#define _UAPI_LINUX_BATMAN_ADV_H_ + +#define BATADV_NL_NAME "batadv" + +#define BATADV_NL_MCAST_GROUP_CONFIG "config" +#define BATADV_NL_MCAST_GROUP_TPMETER "tpmeter" + +/** +* enum batadv_tt_client_flags - TT client specific flags +* +* Bits from 0 to 7 are called _remote flags_ because they are sent on the wire. +* Bits from 8 to 15 are called _local flags_ because they are used for local +* computations only. +* +* Bits from 4 to 7 - a subset of remote flags - are ensured to be in sync with +* the other nodes in the network. To achieve this goal these flags are included +* in the TT CRC computation. +*/ +enum batadv_tt_client_flags { +/** +* @BATADV_TT_CLIENT_DEL: the client has to be deleted from the table +*/ +BATADV_TT_CLIENT_DEL = (1 <<0 ), + +/** +* @BATADV_TT_CLIENT_ROAM: the client roamed to/from another node and +* the new update telling its new real location has not been +* received/sent yet +*/ +BATADV_TT_CLIENT_ROAM = (1 <<1 ), + +/** +* @BATADV_TT_CLIENT_WIFI: this client is connected through a wifi +* interface. This information is used by the "AP Isolation" feature +*/ +BATADV_TT_CLIENT_WIFI = (1 <<4 ), + +/** +* @BATADV_TT_CLIENT_ISOLA: this client is considered "isolated". This +* information is used by the Extended Isolation feature +*/ +BATADV_TT_CLIENT_ISOLA = (1 <<5 ), + +/** +* @BATADV_TT_CLIENT_NOPURGE: this client should never be removed from +* the table +*/ +BATADV_TT_CLIENT_NOPURGE = (1 <<8 ), + +/** +* @BATADV_TT_CLIENT_NEW: this client has been added to the local table +* but has not been announced yet +*/ +BATADV_TT_CLIENT_NEW = (1 <<9 ), + +/** +* @BATADV_TT_CLIENT_PENDING: this client is marked for removal but it +* is kept in the table for one more originator interval for consistency +* purposes +*/ +BATADV_TT_CLIENT_PENDING = (1 <<10 ), + +/** +* @BATADV_TT_CLIENT_TEMP: this global client has been detected to be +* part of the network but no node has already announced it +*/ +BATADV_TT_CLIENT_TEMP = (1 <<11 ), +}; + +/** +* enum batadv_mcast_flags_priv - Private, own multicast flags +* +* These are internal, multicast related flags. Currently they describe certain +* multicast related attributes of the segment this originator bridges into the +* mesh. +* +* Those attributes are used to determine the public multicast flags this +* originator is going to announce via TT. +* +* For netlink, if BATADV_MCAST_FLAGS_BRIDGED is unset then all querier +* related flags are undefined. +*/ +enum batadv_mcast_flags_priv { +/** +* @BATADV_MCAST_FLAGS_BRIDGED: There is a bridge on top of the mesh +* interface. +*/ +BATADV_MCAST_FLAGS_BRIDGED = (1 <<0 ), + +/** +* @BATADV_MCAST_FLAGS_QUERIER_IPV4_EXISTS: Whether an IGMP querier +* exists in the mesh +*/ +BATADV_MCAST_FLAGS_QUERIER_IPV4_EXISTS = (1 <<1 ), + +/** +* @BATADV_MCAST_FLAGS_QUERIER_IPV6_EXISTS: Whether an MLD querier +* exists in the mesh +*/ +BATADV_MCAST_FLAGS_QUERIER_IPV6_EXISTS = (1 <<2 ), + +/** +* @BATADV_MCAST_FLAGS_QUERIER_IPV4_SHADOWING: If an IGMP querier +* exists, whether it is potentially shadowing multicast listeners +* (i.e. querier is behind our own bridge segment) +*/ +BATADV_MCAST_FLAGS_QUERIER_IPV4_SHADOWING = (1 <<3 ), + +/** +* @BATADV_MCAST_FLAGS_QUERIER_IPV6_SHADOWING: If an MLD querier +* exists, whether it is potentially shadowing multicast listeners +* (i.e. querier is behind our own bridge segment) +*/ +BATADV_MCAST_FLAGS_QUERIER_IPV6_SHADOWING = (1 <<4 ), +}; + +/** +* enum batadv_gw_modes - gateway mode of node +*/ +enum batadv_gw_modes { +/** @BATADV_GW_MODE_OFF: gw mode disabled */ +BATADV_GW_MODE_OFF , + +/** @BATADV_GW_MODE_CLIENT: send DHCP requests to gw servers */ +BATADV_GW_MODE_CLIENT , + +/** @BATADV_GW_MODE_SERVER: announce itself as gateway server */ +BATADV_GW_MODE_SERVER , +}; + +/** +* enum batadv_nl_attrs - batman-adv netlink attributes +*/ +enum batadv_nl_attrs { +/** +* @BATADV_ATTR_UNSPEC: unspecified attribute to catch errors +*/ +BATADV_ATTR_UNSPEC , + +/** +* @BATADV_ATTR_VERSION: batman-adv version string +*/ +BATADV_ATTR_VERSION , + +/** +* @BATADV_ATTR_ALGO_NAME: name of routing algorithm +*/ +BATADV_ATTR_ALGO_NAME , + +/** +* @BATADV_ATTR_MESH_IFINDEX: index of the batman-adv interface +*/ +BATADV_ATTR_MESH_IFINDEX , + +/** +* @BATADV_ATTR_MESH_IFNAME: name of the batman-adv interface +*/ +BATADV_ATTR_MESH_IFNAME , + +/** +* @BATADV_ATTR_MESH_ADDRESS: mac address of the batman-adv interface +*/ +BATADV_ATTR_MESH_ADDRESS , + +/** +* @BATADV_ATTR_HARD_IFINDEX: index of the non-batman-adv interface +*/ +BATADV_ATTR_HARD_IFINDEX , + +/** +* @BATADV_ATTR_HARD_IFNAME: name of the non-batman-adv interface +*/ +BATADV_ATTR_HARD_IFNAME , + +/** +* @BATADV_ATTR_HARD_ADDRESS: mac address of the non-batman-adv +* interface +*/ +BATADV_ATTR_HARD_ADDRESS , + +/** +* @BATADV_ATTR_ORIG_ADDRESS: originator mac address +*/ +BATADV_ATTR_ORIG_ADDRESS , + +/** +* @BATADV_ATTR_TPMETER_RESULT: result of run (see +* batadv_tp_meter_status) +*/ +BATADV_ATTR_TPMETER_RESULT , + +/** +* @BATADV_ATTR_TPMETER_TEST_TIME: time (msec) the run took +*/ +BATADV_ATTR_TPMETER_TEST_TIME , + +/** +* @BATADV_ATTR_TPMETER_BYTES: amount of acked bytes during run +*/ +BATADV_ATTR_TPMETER_BYTES , + +/** +* @BATADV_ATTR_TPMETER_COOKIE: session cookie to match tp_meter session +*/ +BATADV_ATTR_TPMETER_COOKIE , + +/** +* @BATADV_ATTR_PAD: attribute used for padding for 64-bit alignment +*/ +BATADV_ATTR_PAD , + +/** +* @BATADV_ATTR_ACTIVE: Flag indicating if the hard interface is active +*/ +BATADV_ATTR_ACTIVE , + +/** +* @BATADV_ATTR_TT_ADDRESS: Client MAC address +*/ +BATADV_ATTR_TT_ADDRESS , + +/** +* @BATADV_ATTR_TT_TTVN: Translation table version +*/ +BATADV_ATTR_TT_TTVN , + +/** +* @BATADV_ATTR_TT_LAST_TTVN: Previous translation table version +*/ +BATADV_ATTR_TT_LAST_TTVN , + +/** +* @BATADV_ATTR_TT_CRC32: CRC32 over translation table +*/ +BATADV_ATTR_TT_CRC32 , + +/** +* @BATADV_ATTR_TT_VID: VLAN ID +*/ +BATADV_ATTR_TT_VID , + +/** +* @BATADV_ATTR_TT_FLAGS: Translation table client flags +*/ +BATADV_ATTR_TT_FLAGS , + +/** +* @BATADV_ATTR_FLAG_BEST: Flags indicating entry is the best +*/ +BATADV_ATTR_FLAG_BEST , + +/** +* @BATADV_ATTR_LAST_SEEN_MSECS: Time in milliseconds since last seen +*/ +BATADV_ATTR_LAST_SEEN_MSECS , + +/** +* @BATADV_ATTR_NEIGH_ADDRESS: Neighbour MAC address +*/ +BATADV_ATTR_NEIGH_ADDRESS , + +/** +* @BATADV_ATTR_TQ: TQ to neighbour +*/ +BATADV_ATTR_TQ , + +/** +* @BATADV_ATTR_THROUGHPUT: Estimated throughput to Neighbour +*/ +BATADV_ATTR_THROUGHPUT , + +/** +* @BATADV_ATTR_BANDWIDTH_UP: Reported uplink bandwidth +*/ +BATADV_ATTR_BANDWIDTH_UP , + +/** +* @BATADV_ATTR_BANDWIDTH_DOWN: Reported downlink bandwidth +*/ +BATADV_ATTR_BANDWIDTH_DOWN , + +/** +* @BATADV_ATTR_ROUTER: Gateway router MAC address +*/ +BATADV_ATTR_ROUTER , + +/** +* @BATADV_ATTR_BLA_OWN: Flag indicating own originator +*/ +BATADV_ATTR_BLA_OWN , + +/** +* @BATADV_ATTR_BLA_ADDRESS: Bridge loop avoidance claim MAC address +*/ +BATADV_ATTR_BLA_ADDRESS , + +/** +* @BATADV_ATTR_BLA_VID: BLA VLAN ID +*/ +BATADV_ATTR_BLA_VID , + +/** +* @BATADV_ATTR_BLA_BACKBONE: BLA gateway originator MAC address +*/ +BATADV_ATTR_BLA_BACKBONE , + +/** +* @BATADV_ATTR_BLA_CRC: BLA CRC +*/ +BATADV_ATTR_BLA_CRC , + +/** +* @BATADV_ATTR_DAT_CACHE_IP4ADDRESS: Client IPv4 address +*/ +BATADV_ATTR_DAT_CACHE_IP4ADDRESS , + +/** +* @BATADV_ATTR_DAT_CACHE_HWADDRESS: Client MAC address +*/ +BATADV_ATTR_DAT_CACHE_HWADDRESS , + +/** +* @BATADV_ATTR_DAT_CACHE_VID: VLAN ID +*/ +BATADV_ATTR_DAT_CACHE_VID , + +/** +* @BATADV_ATTR_MCAST_FLAGS: Per originator multicast flags +*/ +BATADV_ATTR_MCAST_FLAGS , + +/** +* @BATADV_ATTR_MCAST_FLAGS_PRIV: Private, own multicast flags +*/ +BATADV_ATTR_MCAST_FLAGS_PRIV , + +/** +* @BATADV_ATTR_VLANID: VLAN id on top of soft interface +*/ +BATADV_ATTR_VLANID , + +/** +* @BATADV_ATTR_AGGREGATED_OGMS_ENABLED: whether the batman protocol +* messages of the mesh interface shall be aggregated or not. +*/ +BATADV_ATTR_AGGREGATED_OGMS_ENABLED , + +/** +* @BATADV_ATTR_AP_ISOLATION_ENABLED: whether the data traffic going +* from a wireless client to another wireless client will be silently +* dropped. +*/ +BATADV_ATTR_AP_ISOLATION_ENABLED , + +/** +* @BATADV_ATTR_ISOLATION_MARK: the isolation mark which is used to +* classify clients as "isolated" by the Extended Isolation feature. +*/ +BATADV_ATTR_ISOLATION_MARK , + +/** +* @BATADV_ATTR_ISOLATION_MASK: the isolation (bit)mask which is used to +* classify clients as "isolated" by the Extended Isolation feature. +*/ +BATADV_ATTR_ISOLATION_MASK , + +/** +* @BATADV_ATTR_BONDING_ENABLED: whether the data traffic going through +* the mesh will be sent using multiple interfaces at the same time. +*/ +BATADV_ATTR_BONDING_ENABLED , + +/** +* @BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED: whether the bridge loop +* avoidance feature is enabled. This feature detects and avoids loops +* between the mesh and devices bridged with the soft interface +*/ +BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED , + +/** +* @BATADV_ATTR_DISTRIBUTED_ARP_TABLE_ENABLED: whether the distributed +* arp table feature is enabled. This feature uses a distributed hash +* table to answer ARP requests without flooding the request through +* the whole mesh. +*/ +BATADV_ATTR_DISTRIBUTED_ARP_TABLE_ENABLED , + +/** +* @BATADV_ATTR_FRAGMENTATION_ENABLED: whether the data traffic going +* through the mesh will be fragmented or silently discarded if the +* packet size exceeds the outgoing interface MTU. +*/ +BATADV_ATTR_FRAGMENTATION_ENABLED , + +/** +* @BATADV_ATTR_GW_BANDWIDTH_DOWN: defines the download bandwidth which +* is propagated by this node if %BATADV_ATTR_GW_BANDWIDTH_MODE was set +* to 'server'. +*/ +BATADV_ATTR_GW_BANDWIDTH_DOWN , + +/** +* @BATADV_ATTR_GW_BANDWIDTH_UP: defines the upload bandwidth which +* is propagated by this node if %BATADV_ATTR_GW_BANDWIDTH_MODE was set +* to 'server'. +*/ +BATADV_ATTR_GW_BANDWIDTH_UP , + +/** +* @BATADV_ATTR_GW_MODE: defines the state of the gateway features. +* Possible values are specified in enum batadv_gw_modes +*/ +BATADV_ATTR_GW_MODE , + +/** +* @BATADV_ATTR_GW_SEL_CLASS: defines the selection criteria this node +* will use to choose a gateway if gw_mode was set to 'client'. +*/ +BATADV_ATTR_GW_SEL_CLASS , + +/** +* @BATADV_ATTR_HOP_PENALTY: defines the penalty which will be applied +* to an originator message's tq-field on every hop and/or per +* hard interface +*/ +BATADV_ATTR_HOP_PENALTY , + +/** +* @BATADV_ATTR_LOG_LEVEL: bitmask with to define which debug messages +* should be send to the debug log/trace ring buffer +*/ +BATADV_ATTR_LOG_LEVEL , + +/** +* @BATADV_ATTR_MULTICAST_FORCEFLOOD_ENABLED: whether multicast +* optimizations should be replaced by simple broadcast-like flooding +* of multicast packets. If set to non-zero then all nodes in the mesh +* are going to use classic flooding for any multicast packet with no +* optimizations. +*/ +BATADV_ATTR_MULTICAST_FORCEFLOOD_ENABLED , + +/** +* @BATADV_ATTR_NETWORK_CODING_ENABLED: whether Network Coding (using +* some magic to send fewer wifi packets but still the same content) is +* enabled or not. +*/ +BATADV_ATTR_NETWORK_CODING_ENABLED , + +/** +* @BATADV_ATTR_ORIG_INTERVAL: defines the interval in milliseconds in +* which batman sends its protocol messages. +*/ +BATADV_ATTR_ORIG_INTERVAL , + +/** +* @BATADV_ATTR_ELP_INTERVAL: defines the interval in milliseconds in +* which batman emits probing packets for neighbor sensing (ELP). +*/ +BATADV_ATTR_ELP_INTERVAL , + +/** +* @BATADV_ATTR_THROUGHPUT_OVERRIDE: defines the throughput value to be +* used by B.A.T.M.A.N. V when estimating the link throughput using +* this interface. If the value is set to 0 then batman-adv will try to +* estimate the throughput by itself. +*/ +BATADV_ATTR_THROUGHPUT_OVERRIDE , + +/** +* @BATADV_ATTR_MULTICAST_FANOUT: defines the maximum number of packet +* copies that may be generated for a multicast-to-unicast conversion. +* Once this limit is exceeded distribution will fall back to broadcast. +*/ +BATADV_ATTR_MULTICAST_FANOUT , + +/* add attributes above here, update the policy in netlink.c */ + +/** +* @__BATADV_ATTR_AFTER_LAST: internal use +*/ + __BATADV_ATTR_AFTER_LAST, + +/** +* @NUM_BATADV_ATTR: total number of batadv_nl_attrs available +*/ +NUM_BATADV_ATTR = __BATADV_ATTR_AFTER_LAST, + +/** +* @BATADV_ATTR_MAX: highest attribute number currently defined +*/ +BATADV_ATTR_MAX = __BATADV_ATTR_AFTER_LAST -1 +}; + +/** +* enum batadv_nl_commands - supported batman-adv netlink commands +*/ +enum batadv_nl_commands { +/** +* @BATADV_CMD_UNSPEC: unspecified command to catch errors +*/ +BATADV_CMD_UNSPEC , + +/** +* @BATADV_CMD_GET_MESH: Get attributes from softif/mesh +*/ +BATADV_CMD_GET_MESH , + +/** +* @BATADV_CMD_GET_MESH_INFO: Alias for @BATADV_CMD_GET_MESH +*/ +BATADV_CMD_GET_MESH_INFO =BATADV_CMD_GET_MESH , + +/** +* @BATADV_CMD_TP_METER: Start a tp meter session +*/ +BATADV_CMD_TP_METER , + +/** +* @BATADV_CMD_TP_METER_CANCEL: Cancel a tp meter session +*/ +BATADV_CMD_TP_METER_CANCEL , + +/** +* @BATADV_CMD_GET_ROUTING_ALGOS: Query the list of routing algorithms. +*/ +BATADV_CMD_GET_ROUTING_ALGOS , + +/** +* @BATADV_CMD_GET_HARDIF: Get attributes from a hardif of the +* current softif +*/ +BATADV_CMD_GET_HARDIF , + +/** +* @BATADV_CMD_GET_HARDIFS: Alias for @BATADV_CMD_GET_HARDIF +*/ +BATADV_CMD_GET_HARDIFS =BATADV_CMD_GET_HARDIF , + +/** +* @BATADV_CMD_GET_TRANSTABLE_LOCAL: Query list of local translations +*/ +BATADV_CMD_GET_TRANSTABLE_LOCAL , + +/** +* @BATADV_CMD_GET_TRANSTABLE_GLOBAL: Query list of global translations +*/ +BATADV_CMD_GET_TRANSTABLE_GLOBAL , + +/** +* @BATADV_CMD_GET_ORIGINATORS: Query list of originators +*/ +BATADV_CMD_GET_ORIGINATORS , + +/** +* @BATADV_CMD_GET_NEIGHBORS: Query list of neighbours +*/ +BATADV_CMD_GET_NEIGHBORS , + +/** +* @BATADV_CMD_GET_GATEWAYS: Query list of gateways +*/ +BATADV_CMD_GET_GATEWAYS , + +/** +* @BATADV_CMD_GET_BLA_CLAIM: Query list of bridge loop avoidance claims +*/ +BATADV_CMD_GET_BLA_CLAIM , + +/** +* @BATADV_CMD_GET_BLA_BACKBONE: Query list of bridge loop avoidance +* backbones +*/ +BATADV_CMD_GET_BLA_BACKBONE , + +/** +* @BATADV_CMD_GET_DAT_CACHE: Query list of DAT cache entries +*/ +BATADV_CMD_GET_DAT_CACHE , + +/** +* @BATADV_CMD_GET_MCAST_FLAGS: Query list of multicast flags +*/ +BATADV_CMD_GET_MCAST_FLAGS , + +/** +* @BATADV_CMD_SET_MESH: Set attributes for softif/mesh +*/ +BATADV_CMD_SET_MESH , + +/** +* @BATADV_CMD_SET_HARDIF: Set attributes for hardif of the +* current softif +*/ +BATADV_CMD_SET_HARDIF , + +/** +* @BATADV_CMD_GET_VLAN: Get attributes from a VLAN of the +* current softif +*/ +BATADV_CMD_GET_VLAN , + +/** +* @BATADV_CMD_SET_VLAN: Set attributes for VLAN of the +* current softif +*/ +BATADV_CMD_SET_VLAN , + +/* add new commands above here */ + +/** +* @__BATADV_CMD_AFTER_LAST: internal use +*/ + __BATADV_CMD_AFTER_LAST, + +/** +* @BATADV_CMD_MAX: highest used command number +*/ +BATADV_CMD_MAX = __BATADV_CMD_AFTER_LAST -1 +}; + +/** +* enum batadv_tp_meter_reason - reason of a tp meter test run stop +*/ +enum batadv_tp_meter_reason { +/** +* @BATADV_TP_REASON_COMPLETE: sender finished tp run +*/ +BATADV_TP_REASON_COMPLETE =3 , + +/** +* @BATADV_TP_REASON_CANCEL: sender was stopped during run +*/ +BATADV_TP_REASON_CANCEL =4 , + +/* error status >= 128 */ + +/** +* @BATADV_TP_REASON_DST_UNREACHABLE: receiver could not be reached or +* didn't answer +*/ +BATADV_TP_REASON_DST_UNREACHABLE =128 , + +/** +* @BATADV_TP_REASON_RESEND_LIMIT: (unused) sender retry reached limit +*/ +BATADV_TP_REASON_RESEND_LIMIT =129 , + +/** +* @BATADV_TP_REASON_ALREADY_ONGOING: test to or from the same node +* already ongoing +*/ +BATADV_TP_REASON_ALREADY_ONGOING =130 , + +/** +* @BATADV_TP_REASON_MEMORY_ERROR: test was stopped due to low memory +*/ +BATADV_TP_REASON_MEMORY_ERROR =131 , + +/** +* @BATADV_TP_REASON_CANT_SEND: failed to send via outgoing interface +*/ +BATADV_TP_REASON_CANT_SEND =132 , + +/** +* @BATADV_TP_REASON_TOO_MANY: too many ongoing sessions +*/ +BATADV_TP_REASON_TOO_MANY =133 , +}; + +/** +* enum batadv_ifla_attrs - batman-adv ifla nested attributes +*/ +enum batadv_ifla_attrs { +/** +* @IFLA_BATADV_UNSPEC: unspecified attribute which is not parsed by +* rtnetlink +*/ +IFLA_BATADV_UNSPEC , + +/** +* @IFLA_BATADV_ALGO_NAME: routing algorithm (name) which should be +* used by the newly registered batadv net_device. +*/ +IFLA_BATADV_ALGO_NAME , + +/* add attributes above here, update the policy in soft-interface.c */ + +/** +* @__IFLA_BATADV_MAX: internal use +*/ + __IFLA_BATADV_MAX, +}; + +#define IFLA_BATADV_MAX (__IFLA_BATADV_MAX - 1) + +#endif /* _UAPI_LINUX_BATMAN_ADV_H_ */
ip/Makefile +1 -1
@@ -12,7 +12,7 @@ IPOBJ=ip.o ipaddress.o ipaddrlabel.o iproute.o iprule.o ipnetns.o \ iplink_geneve.o iplink_vrf.o iproute_lwtunnel.o ipmacsec.o ipila.o \ ipvrf.o iplink_xstats.o ipseg6.o iplink_netdevsim.o iplink_rmnet.o \ ipnexthop.o ipmptcp.o iplink_bareudp.o iplink_wwan.o ipioam6.o \ - iplink_amt.o + iplink_amt.o iplink_batadv.o RTMONOBJ=rtmon.o
ip/iplink_batadv.c new file +64 -0
64 lines not on this page · raw message
Signature · 1 line
2.35.1