driver core: Add sysfs support for physical location of a device
PATCH v3 1/1 driver core: Add sysfs support for physical location of a device
When ACPI table includes _PLD fields for a device, create a new directory (physical_location) in sysfs to share _PLD fields.
Currently without PLD information, when there are multiple of same devices, it is hard to distinguish which device corresponds to which physical device at which location. For example, when there are two Type C connectors, it is hard to find out which connector corresponds to the Type C port on the left panel versus the Type C port on the right panel. With PLD information provided, we can determine which specific device at which location is doing what.
_PLD output includes much more fields, but only generic fields are added and exposed to sysfs, so that non-ACPI devices can also support it in the future. The minimal generic fields needed for locating a device are the following.
- panel
- vertical_position
- horizontal_position
- dock
- lid
---
Changes from v2
- Use sysfs_emit to create files.
- Correct mix of spaces and tabs.
Changes from v1
- Correct directory names in Documentation.
- Clarify namings in core.c
.../testing/sysfs-devices-physical_location | 42 ++++++ drivers/base/core.c | 139 ++++++++++++++++++ include/linux/device.h | 73 +++++++++ 3 files changed, 254 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-devices-physical_location
Documentation/ABI/testing/sysfs-devices-physical_location new file +42 -0
@@ -0,0 +1,42 @@ +What: /sys/devices/.../physical_location +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + This directory contains information on physical location of + the device connection point with respect to the system's + housing. + +What: /sys/devices/.../physical_location/panel +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + Describes which panel surface of the system’s housing the + device connection point resides on. + +What: /sys/devices/.../physical_location/vertical_position +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + Describes vertical position of the device connection point on + the panel surface. + +What: /sys/devices/.../physical_location/horizontal_position +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + Describes horizontal position of the device connection point on + the panel surface. + +What: /sys/devices/.../physical_location/dock +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + "Yes" if the device connection point resides in a docking + station or a port replicator. "No" otherwise. + +What: /sys/devices/.../physical_location/lid +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + "Yes" if the device connection point resides on the lid of + laptop system. "No" otherwise.
drivers/base/core.c +139 -0
153 lines not on this page · raw message
include/linux/device.h +73 -0
91 lines not on this page · raw message
Signature · 1 line
2.35.1.616.g0bdcbb4464-goog
Greg Kroah-Hartman
maintainerQuoted 104 lines · Won Chung
When ACPI table includes
_PLDfields for a device, create a new directory (physical_location) in sysfs to share_PLDfields.Currently without PLD information, when there are multiple of same devices, it is hard to distinguish which device corresponds to which physical device at which location. For example, when there are two Type C connectors, it is hard to find out which connector corresponds to the Type C port on the left panel versus the Type C port on the right panel. With PLD information provided, we can determine which specific device at which location is doing what.
_PLDoutput includes much more fields, but only generic fields are added and exposed to sysfs, so that non-ACPI devices can also support it in the future. The minimal generic fields needed for locating a device are the following.
- panel
-vertical_position
-horizontal_position
- dock
- lidSigned-off-by Won Chung <[email protected]>---
Changes from v2
- Usesysfs_emitto create files.
- Correct mix of spaces and tabs.Changes from v1
- Correct directory names in Documentation.
- Clarify namings incore.c.../testing/sysfs-devices-physical_location | 42 ++++++ drivers/base/core.c | 139 ++++++++++++++++++ include/linux/device.h | 73 +++++++++ 3 files changed, 254 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-devices-physical_locationDocumentation/ABI/testing/sysfs-devices-physical_location new file +42
-0@@ -0,0 +1,42 @@ +What: /sys/devices/.../physical_location +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + This directory contains information on physical location of + the device connection point with respect to the system's + housing. + +What: /sys/devices/.../physical_location/panel +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + Describes which panel surface of the system’s housing the + device connection point resides on. + +What: /sys/devices/.../physical_location/vertical_position +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + Describes vertical position of the device connection point on + the panel surface. + +What: /sys/devices/.../physical_location/horizontal_position +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + Describes horizontal position of the device connection point on + the panel surface. + +What: /sys/devices/.../physical_location/dock +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + "Yes" if the device connection point resides in a docking + station or a port replicator. "No" otherwise. + +What: /sys/devices/.../physical_location/lid +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + "Yes" if the device connection point resides on the lid of + laptop system. "No" otherwise.drivers/base/core.c +10
-0@@ -2466,6 +2466,136 @@ static ssize_t removable_show(struct device *dev, struct device_attribute *attr, }static DEVICE_ATTR_RO (removable); +static int dev_add_physical_location (struct device *dev) +{ +#if defined(CONFIG_ACPI ) +struct acpi_pld_info *pld; +acpi_status status; + +if (!has_acpi_companion (dev)) +return 0 ; + + status =acpi_get_physical_device_location (ACPI_HANDLE (dev), &pld);
drivers/base/core.c static ssize_t removable_show(struct device *dev, struct device_attribute *attr, · line 2488
Quoted 10 lines
drivers/base/core.c +10
-0+if (ACPI_FAILURE (status) || !pld) +return 0 ; + + dev->location = (struct device_location ) { + .panel = pld->panel, + .vertical_position = pld->vertical_position, + .horizontal_position = pld->horizontal_position, + .dock = pld->dock, + .lid = pld->lid, + };
Is this a memcpy()? Ick, that's odd.
drivers/base/core.c static ssize_t removable_show(struct device *dev, struct device_attribute *attr, · line 2490
Quoted 2 lines
drivers/base/core.c +2
-0+ +return 1 ;
Kernel functions do not return "1" as success. Or as an error. Positive numbers are ONLY for when to return the number of bytes consumed/written or the like.
drivers/base/core.c static ssize_t removable_show(struct device *dev, struct device_attribute *attr, · line 2491
Quoted 1 line
drivers/base/core.c +1
-0+#else
I have asked multiple times to not put #ifdef in .c files. I can't take this patch for that fact alone (also big hint, if acpi is not enabled, loads of these functions and the structure itself should not be present at all...)
Quoted 71 lines
drivers/base/core.c +71
-0+return 0 ; +#endif +} + +static ssize_t panel_show (struct device *dev,struct device_attribute *attr, +char *buf) +{ +const char *panel; + +switch (dev->location.panel) { +case DEVICE_PANEL_TOP : + panel ="top" ; +break ; +case DEVICE_PANEL_BOTTOM : + panel ="bottom" ; +break ; +case DEVICE_PANEL_LEFT : + panel ="left" ; +break ; +case DEVICE_PANEL_RIGHT : + panel ="right" ; +break ; +case DEVICE_PANEL_FRONT : + panel ="front" ; +break ; +case DEVICE_PANEL_BACK : + panel ="back" ; +break ; +default : + panel ="unknown" ; + } +return sysfs_emit (buf,"%s\n" , panel); +} +static DEVICE_ATTR_RO (panel); + +static ssize_t vertical_position_show (struct device *dev, +struct device_attribute *attr,char *buf) +{ +const char *vertical_position; + +switch (dev->location.vertical_position) { +case DEVICE_VERT_POS_UPPER : + vertical_position ="upper" ; +break ; +case DEVICE_VERT_POS_CENTER : + vertical_position ="center" ; +break ; +case DEVICE_VERT_POS_LOWER : + vertical_position ="lower" ; +break ; +default : + vertical_position ="unknown" ; + } +return sysfs_emit (buf,"%s\n" , vertical_position); +} +static DEVICE_ATTR_RO (vertical_position); + +static ssize_t horizontal_position_show (struct device *dev, +struct device_attribute *attr,char *buf) +{ +const char *horizontal_position; + +switch (dev->location.horizontal_position) { +case DEVICE_HORI_POS_LEFT : + horizontal_position ="left" ; +break ; +case DEVICE_HORI_POS_CENTER : + horizontal_position ="center" ; +break ; +case DEVICE_HORI_POS_RIGHT : + horizontal_position ="right" ;
drivers/base/core.c static ssize_t removable_show(struct device *dev, struct device_attribute *attr, · line 2572
Quoted 10 lines
drivers/base/core.c +10
-0+break ; +default : + horizontal_position ="unknown" ; + } +return sysfs_emit (buf,"%s\n" , horizontal_position); +} +static DEVICE_ATTR_RO (horizontal_position); + +static ssize_t dock_show (struct device *dev,struct device_attribute *attr, +char *buf)
Did you run your patch through checkpatch.pl?
Please do so.
Quoted 13 lines
drivers/base/core.c +13
-0+{ +return sysfs_emit (buf,"%s\n" , dev->location.dock ?"yes" :"no" ); +} +static DEVICE_ATTR_RO (dock); + +static ssize_t lid_show (struct device *dev,struct device_attribute *attr, +char *buf) +{ +return sysfs_emit (buf,"%s\n" , dev->location.lid ?"yes" :"no" ); +} +static DEVICE_ATTR_RO (lid); + +static struct attribute *dev_attr_physical_location[] = {
drivers/base/core.c static ssize_t removable_show(struct device *dev, struct device_attribute *attr, · line 2595
Quoted 10 lines
drivers/base/core.c +10
-0+ &dev_attr_panel.attr, + &dev_attr_vertical_position.attr, + &dev_attr_horizontal_position.attr, + &dev_attr_dock.attr, + &dev_attr_lid.attr, + NULL, +}; + +static const struct attribute_group dev_attr_physical_location_group = { + .name = "physical_location",
I'm all for being verbose, but why not just "location"? What other type of location is there for a device?
Quoted 68 lines
drivers/base/core.c +12
-0+ .attrs = dev_attr_physical_location, +}; +int device_add_groups (struct device *dev,const struct attribute_group **groups) {return sysfs_create_groups (&dev->kobj, groups);@@ -2649,8 +2779,17 @@ static int device_add_attrs(struct device *dev) goto err_remove_dev_waiting_for_supplier; } +if (dev_add_physical_location (dev)) { + error =device_add_group (dev, + &dev_attr_physical_location_group); +if (error) + goto err_remove_dev_physical_location; + } +return 0 ; + err_remove_dev_physical_location: +device_remove_group (dev, &dev_attr_physical_location_group); err_remove_dev_waiting_for_supplier:device_remove_file (dev, &dev_attr_waiting_for_supplier); err_remove_dev_online:include/linux/device.h +36
-0@@ -386,6 +386,75 @@ struct dev_msi_info {#endif }; +/** +* enum device_location_panel - Describes which panel surface of the system's +* housing the device connection point resides on. +* @DEVICE_PANEL_TOP: Device connection point is on the top panel. +* @DEVICE_PANEL_BOTTOM: Device connection point is on the bottom panel. +* @DEVICE_PANEL_LEFT: Device connection point is on the left panel. +* @DEVICE_PANEL_RIGHT: Device connection point is on the right panel. +* @DEVICE_PANEL_FRONT: Device connection point is on the front panel. +* @DEVICE_PANEL_BACK: Device connection point is on the back panel. +* @DEVICE_PANEL_UNKNOWN: The panel with device connection point is unknown. +*/ +enum device_location_panel { +DEVICE_PANEL_TOP , +DEVICE_PANEL_BOTTOM , +DEVICE_PANEL_LEFT , +DEVICE_PANEL_RIGHT , +DEVICE_PANEL_FRONT , +DEVICE_PANEL_BACK , +DEVICE_PANEL_UNKNOWN , +}; + +/** +* enum device_location_vertical_position - Describes vertical position of the +* device connection point on the panel surface. +* @DEVICE_VERT_POS_UPPER: Device connection point is at upper part of panel. +* @DEVICE_VERT_POS_CENTER: Device connection point is at center part of panel. +* @DEVICE_VERT_POS_LOWER: Device connection point is at lower part of panel. +*/ +enum device_location_vertical_position { +DEVICE_VERT_POS_UPPER , +DEVICE_VERT_POS_CENTER , +DEVICE_VERT_POS_LOWER , +}; + +/** +* enum device_location_horizontal_position - Describes horizontal position of
include/linux/device.h struct dev_msi_info { · line 434
Quoted 10 lines
include/linux/device.h +10
-0+* the device connection point on the panel surface. +* @DEVICE_HORI_POS_LEFT: Device connection point is at left part of panel. +* @DEVICE_HORI_POS_CENTER: Device connection point is at center part of panel. +* @DEVICE_HORI_POS_RIGHT: Device connection point is at right part of panel. +*/ +enum device_location_horizontal_position { +DEVICE_HORI_POS_LEFT , +DEVICE_HORI_POS_CENTER , +DEVICE_HORI_POS_RIGHT , +};
Why do these enum values need to be in device.h? Can they just live in drivers/base/ somewhere?
Quoted 11 lines
include/linux/device.h +11
-0+ +/** +* struct device_location - Device data related to physical location of the +* device connection point. +* @panel: Panel surface of the system's housing that the device connection +* point resides on. +* @vertical_position: Vertical position of the device connection point within +* the panel. +* @horizontal_position: Horizontal position of the device connection point +* within the panel. +* @dock: Set if the device connection point resides in a docking station or
include/linux/device.h struct dev_msi_info { · line 455
Quoted 10 lines
include/linux/device.h +10
-0+* port replicator. +* @lid: Set if this device connection point resides on the lid of laptop +* system. +*/ +struct device_location { +enum device_location_panel panel; +enum device_location_vertical_position vertical_position; +enum device_location_horizontal_position horizontal_position; +bool dock; +bool lid;
How badly did you just inflate all device structures in the kernel? Did you use 'pahole' to see if you added padding or not?
Quoted 15 lines
include/linux/device.h +4
-0+}; +/** * struct device - The basic device structure * @parent: The device's "parent" device, the device to which it is attached. @@ -456,6 +525,8 @@ struct dev_msi_info {* @removable: Whether the device can be removed from the system. This * should be set by the subsystem / bus driver that discovered * the device. +* @location: Describes physical location of the device connection point in +* the system housing. * * @offline_disabled: If set, the device is permanently online. * @offline: Set after successful invocation of bus type's .offline().
include/linux/device.h struct device { · line 643
Quoted 4 lines
include/linux/device.h +1
-0@@ -569,6 +640,8 @@ struct device {enum device_removable removable; +struct device_location location;
See, you just call it "location" here, not "physical_location", so why does userspace get a bigger name than the kernel does? :)
thanks,
greg k-h
Hi Greg,
Thank you for the review.
I have a few questions on your comments.
Quoted 221 lines · Greg Kroah-Hartman
Quoted 104 lines · Won Chung
When ACPI table includes
_PLDfields for a device, create a new directory (physical_location) in sysfs to share_PLDfields.Currently without PLD information, when there are multiple of same devices, it is hard to distinguish which device corresponds to which physical device at which location. For example, when there are two Type C connectors, it is hard to find out which connector corresponds to the Type C port on the left panel versus the Type C port on the right panel. With PLD information provided, we can determine which specific device at which location is doing what.
_PLDoutput includes much more fields, but only generic fields are added and exposed to sysfs, so that non-ACPI devices can also support it in the future. The minimal generic fields needed for locating a device are the following.
- panel
-vertical_position
-horizontal_position
- dock
- lidSigned-off-by Won Chung <[email protected]>---
Changes from v2
- Usesysfs_emitto create files.
- Correct mix of spaces and tabs.Changes from v1
- Correct directory names in Documentation.
- Clarify namings incore.c.../testing/sysfs-devices-physical_location | 42 ++++++ drivers/base/core.c | 139 ++++++++++++++++++ include/linux/device.h | 73 +++++++++ 3 files changed, 254 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-devices-physical_locationDocumentation/ABI/testing/sysfs-devices-physical_location new file +42
-0@@ -0,0 +1,42 @@ +What: /sys/devices/.../physical_location +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + This directory contains information on physical location of + the device connection point with respect to the system's + housing. + +What: /sys/devices/.../physical_location/panel +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + Describes which panel surface of the system’s housing the + device connection point resides on. + +What: /sys/devices/.../physical_location/vertical_position +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + Describes vertical position of the device connection point on + the panel surface. + +What: /sys/devices/.../physical_location/horizontal_position +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + Describes horizontal position of the device connection point on + the panel surface. + +What: /sys/devices/.../physical_location/dock +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + "Yes" if the device connection point resides in a docking + station or a port replicator. "No" otherwise. + +What: /sys/devices/.../physical_location/lid +Date: March 2022 +Contact: Won Chung <[email protected]> +Description: + "Yes" if the device connection point resides on the lid of + laptop system. "No" otherwise.drivers/base/core.c +10
-0@@ -2466,6 +2466,136 @@ static ssize_t removable_show(struct device *dev, struct device_attribute *attr, }static DEVICE_ATTR_RO (removable); +static int dev_add_physical_location (struct device *dev) +{ +#if defined(CONFIG_ACPI ) +struct acpi_pld_info *pld; +acpi_status status; + +if (!has_acpi_companion (dev)) +return 0 ; + + status =acpi_get_physical_device_location (ACPI_HANDLE (dev), &pld);drivers/base/core.c static ssize_t removable_show(struct device *dev, struct device_attribute *attr, · line 2488
Quoted 10 lines
drivers/base/core.c +10
-0+if (ACPI_FAILURE (status) || !pld) +return 0 ; + + dev->location = (struct device_location ) { + .panel = pld->panel, + .vertical_position = pld->vertical_position, + .horizontal_position = pld->horizontal_position, + .dock = pld->dock, + .lid = pld->lid, + };Is this a
memcpy()? Ick, that's odd.drivers/base/core.c static ssize_t removable_show(struct device *dev, struct device_attribute *attr, · line 2490
Quoted 2 lines
drivers/base/core.c +2
-0+ +return 1 ;Kernel functions do not return "1" as success. Or as an error. Positive numbers are ONLY for when to return the number of bytes consumed/written or the like.
drivers/base/core.c static ssize_t removable_show(struct device *dev, struct device_attribute *attr, · line 2491
Quoted 1 line
drivers/base/core.c +1
-0+#else I have asked multiple times to not put #ifdef in .c files. I can't take this patch for that fact alone (also big hint, if acpi is not enabled, loads of these functions and the structure itself should not be present at all...)
Quoted 71 lines
drivers/base/core.c +71
-0+return 0 ; +#endif +} + +static ssize_t panel_show (struct device *dev,struct device_attribute *attr, +char *buf) +{ +const char *panel; + +switch (dev->location.panel) { +case DEVICE_PANEL_TOP : + panel ="top" ; +break ; +case DEVICE_PANEL_BOTTOM : + panel ="bottom" ; +break ; +case DEVICE_PANEL_LEFT : + panel ="left" ; +break ; +case DEVICE_PANEL_RIGHT : + panel ="right" ; +break ; +case DEVICE_PANEL_FRONT : + panel ="front" ; +break ; +case DEVICE_PANEL_BACK : + panel ="back" ; +break ; +default : + panel ="unknown" ; + } +return sysfs_emit (buf,"%s\n" , panel); +} +static DEVICE_ATTR_RO (panel); + +static ssize_t vertical_position_show (struct device *dev, +struct device_attribute *attr,char *buf) +{ +const char *vertical_position; + +switch (dev->location.vertical_position) { +case DEVICE_VERT_POS_UPPER : + vertical_position ="upper" ; +break ; +case DEVICE_VERT_POS_CENTER : + vertical_position ="center" ; +break ; +case DEVICE_VERT_POS_LOWER : + vertical_position ="lower" ; +break ; +default : + vertical_position ="unknown" ; + } +return sysfs_emit (buf,"%s\n" , vertical_position); +} +static DEVICE_ATTR_RO (vertical_position); + +static ssize_t horizontal_position_show (struct device *dev, +struct device_attribute *attr,char *buf) +{ +const char *horizontal_position; + +switch (dev->location.horizontal_position) { +case DEVICE_HORI_POS_LEFT : + horizontal_position ="left" ; +break ; +case DEVICE_HORI_POS_CENTER : + horizontal_position ="center" ; +break ; +case DEVICE_HORI_POS_RIGHT : + horizontal_position ="right" ;drivers/base/core.c static ssize_t removable_show(struct device *dev, struct device_attribute *attr, · line 2572
Quoted 10 lines
drivers/base/core.c +10
-0+break ; +default : + horizontal_position ="unknown" ; + } +return sysfs_emit (buf,"%s\n" , horizontal_position); +} +static DEVICE_ATTR_RO (horizontal_position); + +static ssize_t dock_show (struct device *dev,struct device_attribute *attr, +char *buf)Did you run your patch through checkpatch.pl?
Quoted 2 lines
Please do so.
I think I did run checkpatch.pl. I tried again but there is no issue other than a warning that the maintainers list may need to be updated due to a new file. Do you think there is a style issue here?
Quoted 18 lines
Quoted 18 lines
drivers/base/core.c +18
-0+{ +return sysfs_emit (buf,"%s\n" , dev->location.dock ?"yes" :"no" ); +} +static DEVICE_ATTR_RO (dock); + +static ssize_t lid_show (struct device *dev,struct device_attribute *attr, +char *buf) +{ +return sysfs_emit (buf,"%s\n" , dev->location.lid ?"yes" :"no" ); +} +static DEVICE_ATTR_RO (lid); + +static struct attribute *dev_attr_physical_location[] = { + &dev_attr_panel.attr, + &dev_attr_vertical_position.attr, + &dev_attr_horizontal_position.attr, + &dev_attr_dock.attr, + &dev_attr_lid.attr,
Quoted 8 lines
drivers/base/core.c static ssize_t removable_show(struct device *dev, struct device_attribute *attr, · line 2595
Quoted 5 lines
drivers/base/core.c +5
-0+ NULL, +}; + +static const struct attribute_group dev_attr_physical_location_group = { + .name ="physical_location" ,I'm all for being verbose, but why not just "location"? What other type of location is there for a device?
For USB ports, there seems to be a "location" file for u32 value representing ACPI PLD group token and group location.
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/usb/core/port.c#n20
Would you prefer renaming that "location" file to something else and have this one as "location" directory? Or would "physical_location" be okay?
Quoted 74 lines
Quoted 74 lines
drivers/base/core.c +12
-0+ .attrs = dev_attr_physical_location, +}; +int device_add_groups (struct device *dev,const struct attribute_group **groups) {return sysfs_create_groups (&dev->kobj, groups);@@ -2649,8 +2779,17 @@ static int device_add_attrs(struct device *dev) goto err_remove_dev_waiting_for_supplier; } +if (dev_add_physical_location (dev)) { + error =device_add_group (dev, + &dev_attr_physical_location_group); +if (error) + goto err_remove_dev_physical_location; + } +return 0 ; + err_remove_dev_physical_location: +device_remove_group (dev, &dev_attr_physical_location_group); err_remove_dev_waiting_for_supplier:device_remove_file (dev, &dev_attr_waiting_for_supplier); err_remove_dev_online:include/linux/device.h +41
-0@@ -386,6 +386,75 @@ struct dev_msi_info {#endif }; +/** +* enum device_location_panel - Describes which panel surface of the system's +* housing the device connection point resides on. +* @DEVICE_PANEL_TOP: Device connection point is on the top panel. +* @DEVICE_PANEL_BOTTOM: Device connection point is on the bottom panel. +* @DEVICE_PANEL_LEFT: Device connection point is on the left panel. +* @DEVICE_PANEL_RIGHT: Device connection point is on the right panel. +* @DEVICE_PANEL_FRONT: Device connection point is on the front panel. +* @DEVICE_PANEL_BACK: Device connection point is on the back panel. +* @DEVICE_PANEL_UNKNOWN: The panel with device connection point is unknown. +*/ +enum device_location_panel { +DEVICE_PANEL_TOP , +DEVICE_PANEL_BOTTOM , +DEVICE_PANEL_LEFT , +DEVICE_PANEL_RIGHT , +DEVICE_PANEL_FRONT , +DEVICE_PANEL_BACK , +DEVICE_PANEL_UNKNOWN , +}; + +/** +* enum device_location_vertical_position - Describes vertical position of the +* device connection point on the panel surface. +* @DEVICE_VERT_POS_UPPER: Device connection point is at upper part of panel. +* @DEVICE_VERT_POS_CENTER: Device connection point is at center part of panel. +* @DEVICE_VERT_POS_LOWER: Device connection point is at lower part of panel. +*/ +enum device_location_vertical_position { +DEVICE_VERT_POS_UPPER , +DEVICE_VERT_POS_CENTER , +DEVICE_VERT_POS_LOWER , +}; + +/** +* enum device_location_horizontal_position - Describes horizontal position of +* the device connection point on the panel surface. +* @DEVICE_HORI_POS_LEFT: Device connection point is at left part of panel. +* @DEVICE_HORI_POS_CENTER: Device connection point is at center part of panel. +* @DEVICE_HORI_POS_RIGHT: Device connection point is at right part of panel. +*/
Quoted 9 lines
include/linux/device.h struct dev_msi_info { · line 434
Quoted 5 lines
include/linux/device.h +5
-0+enum device_location_horizontal_position { +DEVICE_HORI_POS_LEFT , +DEVICE_HORI_POS_CENTER , +DEVICE_HORI_POS_RIGHT , +};Why do these enum values need to be in
device.h? Can they just live indrivers/base/somewhere?
I was thinking that since these are information about device, they could live in and be accessed through device.
Do you think this is not a good place for these enum and struct? Maybe a new driver/base/location.h?
Quoted 17 lines
Quoted 17 lines
include/linux/device.h +16
-0+ +/** +* struct device_location - Device data related to physical location of the +* device connection point. +* @panel: Panel surface of the system's housing that the device connection +* point resides on. +* @vertical_position: Vertical position of the device connection point within +* the panel. +* @horizontal_position: Horizontal position of the device connection point +* within the panel. +* @dock: Set if the device connection point resides in a docking station or +* port replicator. +* @lid: Set if this device connection point resides on the lid of laptop +* system. +*/ +struct device_location {
Quoted 9 lines
include/linux/device.h struct dev_msi_info { · line 455
Quoted 5 lines
include/linux/device.h +5
-0+enum device_location_panel panel; +enum device_location_vertical_position vertical_position; +enum device_location_horizontal_position horizontal_position; +bool dock; +bool lid;How badly did you just inflate all device structures in the kernel? Did you use 'pahole' to see if you added padding or not?
I did not use pahole. I tried it and it is giving 16 bytes for struct device_location and 2 bytes of padding.
Would using device location* instead be better since that would be 8 bytes of inflation?
Quoted 18 lines
Quoted 18 lines
include/linux/device.h +4
-0+}; +/** * struct device - The basic device structure * @parent: The device's "parent" device, the device to which it is attached. @@ -456,6 +525,8 @@ struct dev_msi_info {* @removable: Whether the device can be removed from the system. This * should be set by the subsystem / bus driver that discovered * the device. +* @location: Describes physical location of the device connection point in +* the system housing. * * @offline_disabled: If set, the device is permanently online. * @offline: Set after successful invocation of bus type's .offline(). @@ -569,6 +640,8 @@ struct device {enum device_removable removable;
Quoted 8 lines
include/linux/device.h struct device { · line 643
Quoted 1 line
include/linux/device.h +1
-0+struct device_location location;See, you just call it "location" here, not "
physical_location", so why does userspace get a bigger name than the kernel does? :)thanks,
greg k-h
Thank you,
Won