fix dw-mmc-rockchip rk356x clock rates
v3 cover fix dw-mmc-rockchip rk356x clock rates
While lighting off support for the SoQuartz module, it was discoved the dw-mmc-rockchip driver has tremendous log spam when the cd-broken flag is enabled and no card is inserted.
The SoQuart requires the cd-broken flag as the CM4 module pinout it follows has no card-detect pin.
These errors occur during card initialization on all rk356x chips, but are amplified by cd-broken as the function is called multiple times each poll cycle.
It was discovered the lowest possible clock rate the rk356x cru can provide for the ciu clock in the default configuration is 750khz. There is an internal clock divider that makes the final minimum clock 375khz. We could hardcode this, but it is possible it could change if the default clock configuration changes.
To fix this, we must make two changes:
First, the dw-mmc core needs to be updated to allow a host driver to save its requested minimum frequency. This is necessary as the mmc_host struct isn't available when the host drivers initialization code is called. The dw-mmc core can then apply the f_min later when the struct is available.
Second, the dw-mmc-rockchip driver is extended to test the frequencies mmc core will use during card initialization. It finds the lowest supported frequency from the cru and saves it for later use by dw-mmc core.
Changelog:
v3:
- add support in dw_mmc core for saving the minimum frequency (fixes setting f_min)
- add test for the lowest supported frequency to avoid clamping configs that don't have an error
v2:
- change from muting the error to attempting to fix the underlying issue by setting f_min in driver initialization
Peter Geis (2):
mmc: host: dw_mmc: support setting f_min from host drivers
mmc: host: dw-mmc-rockchip: fix handling invalid clock rates
drivers/mmc/host/dw_mmc-rockchip.c | 27 +++++++++++++++++++++++---- drivers/mmc/host/dw_mmc.c | 7 ++++++- drivers/mmc/host/dw_mmc.h | 2 ++ 3 files changed, 31 insertions(+), 5 deletions(-)
Signature · 1 line
2.25.1
PATCH v3 1/2 mmc: host: dw_mmc: support setting f_min from host drivers
Host drivers may not be able to support frequencies as low as dw-mmc supports. Unfortunately f_min isn't available when the drv_data->init function is called, as the mmc_host struct hasn't been set up yet.
Support the host drivers saving the requested minimum frequency, so we can later set f_min when it is available.
--- drivers/mmc/host/dw_mmc.c | 7 ++++++- drivers/mmc/host/dw_mmc.h | 2 ++ 2 files changed, 8 insertions(+), 1 deletion(-)
drivers/mmc/host/dw_mmc.c +6 -1
@@ -2898,7 +2898,12 @@ static int dw_mci_init_slot_caps(struct dw_mci_slot *slot)if (host->pdata->caps2) mmc->caps2 = host->pdata->caps2; - mmc->f_min =DW_MCI_FREQ_MIN ; +/* if host has set a minimum_freq, we should respect it */ +if (host->minimum_speed) + mmc->f_min = host->minimum_speed; +else + mmc->f_min =DW_MCI_FREQ_MIN ; +if (!mmc->f_max) mmc->f_max =DW_MCI_FREQ_MAX ;
drivers/mmc/host/dw_mmc.h +2 -0
@@ -99,6 +99,7 @@ struct dw_mci_dma_slave {* @bus_hz: The rate of @mck in Hz. This forms the basis for MMC bus * rate and timeout calculations. * @current_speed: Configured rate of the controller. +* @minimum_speed: Stored minimum rate of the controller. * @fifoth_val: The value of FIFOTH register. * @verid: Denote Version ID. * @dev: Device associated with the MMC controller.
@@ -201,6 +202,7 @@ struct dw_mci {u32 bus_hz;u32 current_speed; +u32 minimum_speed;u32 fifoth_val;u16 verid;struct device *dev;
Signature · 1 line
2.25.1
Re: [PATCH v3 1/2] mmc: host: dw_mmc: support setting f_min from host drivers
Quoted 9 lines · Peter Geis
Host drivers may not be able to support frequencies as low as dw-mmc supports. Unfortunately
f_minisn't available when thedrv_data->initfunction is called, as themmc_hoststruct hasn't been set up yet.Support the host drivers saving the requested minimum frequency, so we can later set
f_minwhen it is available.Signed-off-by Peter Geis <[email protected]>
Applied for next, thanks!
Kind regards
Uffe
Quoted 46 lines
--- drivers/mmc/host/dw_mmc.c | 7 ++++++- drivers/mmc/host/dw_mmc.h | 2 ++ 2 files changed, 8 insertions(+), 1 deletion(-)drivers/mmc/host/dw_mmc.c +6
-1@@ -2898,7 +2898,12 @@ static int dw_mci_init_slot_caps(struct dw_mci_slot *slot)if (host->pdata->caps2) mmc->caps2 = host->pdata->caps2; - mmc->f_min =DW_MCI_FREQ_MIN ; +/* if host has set a minimum_freq, we should respect it */ +if (host->minimum_speed) + mmc->f_min = host->minimum_speed; +else + mmc->f_min =DW_MCI_FREQ_MIN ; +if (!mmc->f_max) mmc->f_max =DW_MCI_FREQ_MAX ;drivers/mmc/host/dw_mmc.h +2
-1@@ -99,6 +99,7 @@ struct dw_mci_dma_slave {* @bus_hz: The rate of @mck in Hz. This forms the basis for MMC bus * rate and timeout calculations. * @current_speed: Configured rate of the controller. +* @minimum_speed: Stored minimum rate of the controller. * @fifoth_val: The value of FIFOTH register. * @verid: Denote Version ID. * @dev: Device associated with the MMC controller. @@ -201,6 +202,7 @@ struct dw_mci {u32 bus_hz;u32 current_speed; +u32 minimum_speed;u32 fifoth_val;u16 verid;struct device *dev; --2.25.1
PATCH v3 2/2 mmc: host: dw-mmc-rockchip: fix handling invalid clock rates
In reply to Peter GeisThe Rockchip rk356x ciu clock cannot be set as low as the dw-mmc hardware supports. This leads to a situation during card initialization where the clock is set lower than the clock driver can support. The dw-mmc-rockchip driver spews errors when this happens.
For normal operation this only happens a few times during boot, but when cd-broken is enabled (in cases such as the SoQuartz module) this fires multiple times each poll cycle.
Fix this by testing the lowest possible frequency that the clock driver can support which is within the mmc specification. Divide that rate by the internal divider and set f_min to this.
--- drivers/mmc/host/dw_mmc-rockchip.c | 27 +++++++++++++++++++++++---- 1 file changed, 23 insertions(+), 4 deletions(-)
drivers/mmc/host/dw_mmc-rockchip.c +23 -4
@@ -15,7 +15,9 @@#include "dw_mmc.h" #include "dw_mmc-pltfm.h" -#define RK3288_CLKGEN_DIV 2 +#define RK3288_CLKGEN_DIV 2 + +static const unsigned int freqs[] = {100000 ,200000 ,300000 ,400000 };struct dw_mci_rockchip_priv_data {struct clk *drv_clk;
@@ -51,7 +53,7 @@ static void dw_mci_rk3288_set_ios(struct dw_mci *host, struct mmc_ios *ios) ret =clk_set_rate (host->ciu_clk, cclkin);if (ret) -dev_warn (host->dev,"failed to set rate %uHz\n" , ios->clock); +dev_warn (host->dev,"failed to set rate %uHz err: %d\n" , cclkin, ret); bus_hz =clk_get_rate (host->ciu_clk) /RK3288_CLKGEN_DIV ;if (bus_hz != host->bus_hz) {
@@ -290,13 +292,30 @@ static int dw_mci_rk3288_parse_dt(struct dw_mci *host)static int dw_mci_rockchip_init (struct dw_mci *host) { +int ret, i; +/* It is slot 8 on Rockchip SoCs */ host->sdio_id0 =8 ; -if (of_device_is_compatible (host->dev->of_node, -"rockchip,rk3288-dw-mshc" )) +if (of_device_is_compatible (host->dev->of_node,"rockchip,rk3288-dw-mshc" )) { host->bus_hz /=RK3288_CLKGEN_DIV ; +/* clock driver will fail if the clock is less than the lowest source clock +* divided by the internal clock divider. Test for the lowest available +* clock and set the minimum freq to clock / clock divider. +*/ + +for (i =0 ; i <ARRAY_SIZE (freqs); i++) { + ret =clk_round_rate (host->ciu_clk, freqs[i] *RK3288_CLKGEN_DIV ); +if (ret >0 ) { + host->minimum_speed = ret /RK3288_CLKGEN_DIV ; +break ; + } + } +if (ret <0 ) +dev_warn (host->dev,"no valid minimum freq: %d\n" , ret); + } +return 0 ; }
Signature · 1 line
2.25.1
Re: [PATCH v3 2/2] mmc: host: dw-mmc-rockchip: fix handling invalid clock rates
Quoted 9 lines · Peter Geis
The Rockchip rk356x ciu clock cannot be set as low as the dw-mmc hardware supports. This leads to a situation during card initialization where the clock is set lower than the clock driver can support. The dw-mmc-rockchip driver spews errors when this happens.
For normal operation this only happens a few times during boot, but when cd-broken is enabled (in cases such as the SoQuartz module) this fires multiple times each poll cycle.
Quoted 5 lines
Fix this by testing the lowest possible frequency that the clock driver can support which is within the mmc specification. Divide that rate by the internal divider and set
f_minto this.Signed-off-by Peter Geis <[email protected]>
Applied for next, thanks!
Kind regards
Uffe
Quoted 64 lines
--- drivers/mmc/host/dw_mmc-rockchip.c | 27 +++++++++++++++++++++++---- 1 file changed, 23 insertions(+), 4 deletions(-)drivers/mmc/host/dw_mmc-rockchip.c +23
-5@@ -15,7 +15,9 @@#include "dw_mmc.h" #include "dw_mmc-pltfm.h" -#define RK3288_CLKGEN_DIV 2 +#define RK3288_CLKGEN_DIV 2 + +static const unsigned int freqs[] = {100000 ,200000 ,300000 ,400000 };struct dw_mci_rockchip_priv_data {struct clk *drv_clk;@@ -51,7 +53,7 @@ static void dw_mci_rk3288_set_ios(struct dw_mci *host, struct mmc_ios *ios) ret =clk_set_rate (host->ciu_clk, cclkin);if (ret) -dev_warn (host->dev,"failed to set rate %uHz\n" , ios->clock); +dev_warn (host->dev,"failed to set rate %uHz err: %d\n" , cclkin, ret); bus_hz =clk_get_rate (host->ciu_clk) /RK3288_CLKGEN_DIV ;if (bus_hz != host->bus_hz) {@@ -290,13 +292,30 @@ static int dw_mci_rk3288_parse_dt(struct dw_mci *host)static int dw_mci_rockchip_init (struct dw_mci *host) { +int ret, i; +/* It is slot 8 on Rockchip SoCs */ host->sdio_id0 =8 ; -if (of_device_is_compatible (host->dev->of_node, -"rockchip,rk3288-dw-mshc" )) +if (of_device_is_compatible (host->dev->of_node,"rockchip,rk3288-dw-mshc" )) { host->bus_hz /=RK3288_CLKGEN_DIV ; +/* clock driver will fail if the clock is less than the lowest source clock +* divided by the internal clock divider. Test for the lowest available +* clock and set the minimum freq to clock / clock divider. +*/ + +for (i =0 ; i <ARRAY_SIZE (freqs); i++) { + ret =clk_round_rate (host->ciu_clk, freqs[i] *RK3288_CLKGEN_DIV ); +if (ret >0 ) { + host->minimum_speed = ret /RK3288_CLKGEN_DIV ; +break ; + } + } +if (ret <0 ) +dev_warn (host->dev,"no valid minimum freq: %d\n" , ret); + } +return 0 ; } --2.25.1