Skip to contentSkip to conversation

bcm6753: add initial support

PATCH In review Philippe Reynes 2 participants 10 messages Feb 11, 2022 – Mar 7, 2022

Subsystems (6)
lore
Share & tools
lore
#0 lore raw

PATCH 1/5 bcm6753: add initial support

This add the initial support of the broadcom bcm6753 SoC family.

---
 arch/arm/Kconfig          |   7 ++
 arch/arm/dts/bcm6753.dtsi | 201 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 208 insertions(+)
 create mode 100644 arch/arm/dts/bcm6753.dtsi
arch/arm/Kconfig +7 -0
index 8053394389..07a1b713cb 100644
@@ -617,6 +617,13 @@ config ARCH_BCM63158
 	select OF_CONTROL
 	imply CMD_DM
 
+config ARCH_BCM6753
+	bool "Broadcom BCM6753 family"
+	select CPU_V7A
+	select DM
+	select OF_CONTROL
+	imply CMD_DM
+
 config ARCH_BCM68360
 	bool "Broadcom BCM68360 family"
 	select DM
arch/arm/dts/bcm6753.dtsi new file +201 -0

201 lines not on this page · raw message

Signature · 1 line
2.17.1
#1 lore raw

PATCH 2/5 gpio: bcm6345: allow to use this driver on arm bcm6753

This IP is also used on some arm SoC, so we allow to use it on arm bcm6753 too.

---
 drivers/gpio/Kconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpio/Kconfig +2 -1
index 8d0e47c67d..1c963c2c53 100644
@@ -87,7 +87,8 @@ config ALTERA_PIO
 config BCM6345_GPIO
 	bool "BCM6345 GPIO driver"
 	depends on DM_GPIO && (ARCH_BMIPS || ARCH_BCM68360 || \
-			       ARCH_BCM6858 || ARCH_BCM63158)
+			       ARCH_BCM6858 || ARCH_BCM63158 || \
+			       ARCH_BCM6753)
 	help
 	  This driver supports the GPIO banks on BCM6345 SoCs.
 
Signature · 1 line
2.17.1
#2 lore raw

Re: [PATCH 2/5] gpio: bcm6345: allow to use this driver on arm bcm6753

Quoted 4 lines · Philippe Reynes

This IP is also used on some arm SoC, so we allow to use it on arm bcm6753 too.

Applied to u-boot/next, thanks!

Signature · 1 line
Tom
#3 lore raw

PATCH 3/5 nand: brcmnand: add bcm6753 support

In reply to Philippe Reynes

This adds the nand support for chipset bcm6753.

---
 drivers/mtd/nand/raw/Kconfig                 |   6 +
 drivers/mtd/nand/raw/brcmnand/Makefile       |   1 +
 drivers/mtd/nand/raw/brcmnand/bcm6753_nand.c | 124 +++++++++++++++++++
 3 files changed, 131 insertions(+)
 create mode 100644 drivers/mtd/nand/raw/brcmnand/bcm6753_nand.c
drivers/mtd/nand/raw/Kconfig +6 -0
index 0e826c1929..1eab21e206 100644
@@ -91,6 +91,12 @@ config NAND_BRCMNAND_6368
 	help
 	  Enable support for broadcom nand driver on bcm6368.
 
+config NAND_BRCMNAND_6753
+	bool "Support Broadcom NAND controller on bcm6753"
+	depends on NAND_BRCMNAND && ARCH_BCM6753
+	help
+	  Enable support for broadcom nand driver on bcm6753.
+
 config NAND_BRCMNAND_68360
        bool "Support Broadcom NAND controller on bcm68360"
        depends on NAND_BRCMNAND && ARCH_BCM68360
drivers/mtd/nand/raw/brcmnand/Makefile +1 -0
index 5d9e7e3f3b..f46a7edae3 100644
@@ -2,6 +2,7 @@
 
 obj-$(CONFIG_NAND_BRCMNAND_6368) += bcm6368_nand.o
 obj-$(CONFIG_NAND_BRCMNAND_63158) += bcm63158_nand.o
+obj-$(CONFIG_NAND_BRCMNAND_6753) += bcm6753_nand.o
 obj-$(CONFIG_NAND_BRCMNAND_68360) += bcm68360_nand.o
 obj-$(CONFIG_NAND_BRCMNAND_6838) += bcm6838_nand.o
 obj-$(CONFIG_NAND_BRCMNAND_6858) += bcm6858_nand.o
drivers/mtd/nand/raw/brcmnand/bcm6753_nand.c new file +124 -0

124 lines not on this page · raw message

Signature · 1 line
2.17.1
#4 lore raw

Re: [PATCH 3/5] nand: brcmnand: add bcm6753 support

Quoted 3 lines · Philippe Reynes

This adds the nand support for chipset bcm6753.

Applied to u-boot/next, thanks!

Signature · 1 line
Tom
#5 lore raw

PATCH 4/5 watchdog: bcm6345: allow to use this driver on arm bcm6753

In reply to Philippe Reynes

This IP is also used on some arm SoC, so we allow to use it on arm bcm6753 too.

---
 drivers/watchdog/Kconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/watchdog/Kconfig +2 -1
index cabac29053..1f3ca99f9a 100644
@@ -129,7 +129,8 @@ config WDT_AT91
 config WDT_BCM6345
 	bool "BCM6345 watchdog timer support"
 	depends on WDT && (ARCH_BMIPS || ARCH_BCM68360 || \
-			   ARCH_BCM6858 || ARCH_BCM63158)
+			   ARCH_BCM6858 || ARCH_BCM63158 || \
+			   ARCH_BCM6753)
 	help
 	  Select this to enable watchdog timer for BCM6345 SoCs.
 	  The watchdog timer is stopped when initialized.
Signature · 1 line
2.17.1
#6 lore raw

Re: [PATCH 4/5] watchdog: bcm6345: allow to use this driver on arm bcm6753

Quoted 4 lines · Philippe Reynes

This IP is also used on some arm SoC, so we allow to use it on arm bcm6753 too.

Applied to u-boot/next, thanks!

Signature · 1 line
Tom
#7 lore raw

PATCH 5/5 bcm96753ref: add initial support

In reply to Philippe Reynes

This add the initial support of the broadcom reference board bcm96753ref with a bcm6753 SoC.

This board has 1 GB of RAM, 256 MB of flash (nand), 2 USB port, 1 UART, and 4 ethernet ports.

---
 arch/arm/Kconfig                         |  1 +
 arch/arm/dts/Makefile                    |  3 +
 arch/arm/dts/bcm96753ref.dts             | 80 +++++++++++++++++++++++
 board/broadcom/bcm96753ref/Kconfig       | 16 +++++
 board/broadcom/bcm96753ref/MAINTAINERS   |  6 ++
 board/broadcom/bcm96753ref/Makefile      |  3 +
 board/broadcom/bcm96753ref/bcm96753ref.c | 40 ++++++++++++
 configs/bcm96753ref_ram_defconfig        | 81 ++++++++++++++++++++++++
 include/configs/broadcom_bcm96753ref.h   | 34 ++++++++++
 9 files changed, 264 insertions(+)
 create mode 100644 arch/arm/dts/bcm96753ref.dts
 create mode 100644 board/broadcom/bcm96753ref/Kconfig
 create mode 100644 board/broadcom/bcm96753ref/MAINTAINERS
 create mode 100644 board/broadcom/bcm96753ref/Makefile
 create mode 100644 board/broadcom/bcm96753ref/bcm96753ref.c
 create mode 100644 configs/bcm96753ref_ram_defconfig
 create mode 100644 include/configs/broadcom_bcm96753ref.h
arch/arm/Kconfig +1 -0
index 07a1b713cb..40fb2e1d5c 100644
@@ -2213,6 +2213,7 @@ source "board/armltd/vexpress/Kconfig"
 source "board/armltd/vexpress64/Kconfig"
 source "board/cortina/presidio-asic/Kconfig"
 source "board/broadcom/bcm963158/Kconfig"
+source "board/broadcom/bcm96753ref/Kconfig"
 source "board/broadcom/bcm968360bg/Kconfig"
 source "board/broadcom/bcm968580xref/Kconfig"
 source "board/broadcom/bcmns3/Kconfig"
arch/arm/dts/Makefile +3 -0
index c1cec726cf..03f7e91612 100644
@@ -1101,6 +1101,9 @@ dtb-$(CONFIG_ARCH_BCM63158) += \
 dtb-$(CONFIG_ARCH_BCM68360) += \
 	bcm968360bg.dtb
 
+dtb-$(CONFIG_ARCH_BCM6753) += \
+	bcm96753ref.dtb
+
 dtb-$(CONFIG_ARCH_BCM6858) += \
 	bcm968580xref.dtb
 
arch/arm/dts/bcm96753ref.dts new file +80 -0

80 lines not on this page · raw message

board/broadcom/bcm96753ref/Kconfig new file +16 -0
new file mode 100644
index 0000000000..479e790578
@@ -0,0 +1,16 @@
+if TARGET_BCM96753REF
+
+config SYS_VENDOR
+	default "broadcom"
+
+config SYS_BOARD
+	default "bcm96753ref"
+
+config SYS_CONFIG_NAME
+	default "broadcom_bcm96753ref"
+
+endif
+
+config TARGET_BCM96753REF
+	bool "Support Broadcom bcm96753ref"
+	depends on ARCH_BCM6753
board/broadcom/bcm96753ref/MAINTAINERS new file +6 -0
new file mode 100644
index 0000000000..be060f5a70
@@ -0,0 +1,6 @@
+BROADCOM BCM96753REF
+M:	Philippe Reynes <[email protected]>
+S:	Maintained
+F:	board/broadcom/bcm96753ref
+F:	include/configs/broadcom_bcm96753ref.h
+F:	configs/bcm96753ref_ram_defconfig
board/broadcom/bcm96753ref/Makefile new file +3 -0
new file mode 100644
index 0000000000..a1fa2bff86
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y	+= bcm96753ref.o
board/broadcom/bcm96753ref/bcm96753ref.c new file +40 -0
new file mode 100644
index 0000000000..bf78d843aa
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2022 Philippe Reynes <[email protected]>
+ */
+
+#include <common.h>
+#include <fdtdec.h>
+#include <linux/io.h>
+#include <cpu_func.h>
+
+int board_init(void)
+{
+	return 0;
+}
+
+int dram_init(void)
+{
+	if (fdtdec_setup_mem_size_base() != 0)
+		printf("fdtdec_setup_mem_size_base() has failed\n");
+
+	return 0;
+}
+
+int dram_init_banksize(void)
+{
+	fdtdec_setup_memory_banksize();
+
+	return 0;
+}
+
+int print_cpuinfo(void)
+{
+	return 0;
+}
+
+void enable_caches(void)
+{
+	icache_enable();
+	dcache_enable();
+}
configs/bcm96753ref_ram_defconfig new file +81 -0

81 lines not on this page · raw message

include/configs/broadcom_bcm96753ref.h new file +34 -0
new file mode 100644
index 0000000000..c002985cf4
@@ -0,0 +1,34 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2022 Philippe Reynes <[email protected]>
+ */
+
+#include <linux/sizes.h>
+
+/*
+ * common
+ */
+
+/* UART */
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, \
+					  230400, 500000, 1500000 }
+/* Memory usage */
+#define CONFIG_SYS_MAXARGS		24
+
+/*
+ * 6853
+ */
+
+/* RAM */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+
+/* U-Boot */
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE + SZ_16M)
+
+#ifdef CONFIG_MTD_RAW_NAND
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#endif /* CONFIG_MTD_RAW_NAND */
+
+/*
+ * 96753ref
+ */
Signature · 1 line
2.17.1
#8 lore raw

Re: [PATCH 5/5] bcm96753ref: add initial support

Quoted 7 lines · Philippe Reynes

This add the initial support of the broadcom reference board bcm96753ref with a bcm6753 SoC.

This board has 1 GB of RAM, 256 MB of flash (nand), 2 USB port, 1 UART, and 4 ethernet ports.

Applied to u-boot/next, thanks!

Signature · 1 line
Tom