Skip to contentSkip to conversation

PCI: Enable INTx quirk for ATI PCIe-USB adapter

PATCH In review Andy Shevchenko 4 participants 15 messages Mar 14, 2022 – Mar 18, 2022 PCI

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 PCI: Enable INTx quirk for ATI PCIe-USB adapter

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI devices")
Reported-by [email protected]
---
 drivers/pci/quirks.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/pci/quirks.c +7 -0
index 65f7f6b0576c..cc6a87a32b62 100644
@@ -3041,6 +3041,13 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
 			PCI_DEVICE_ID_TIGON3_5715S,
 			quirk_msi_intx_disable_bug);
 
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4386, quirk_msi_intx_disable_bug);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4387, quirk_msi_intx_disable_bug);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4388, quirk_msi_intx_disable_bug);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4389, quirk_msi_intx_disable_bug);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438a, quirk_msi_intx_disable_bug);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438b, quirk_msi_intx_disable_bug);
+
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4390,
 			quirk_msi_intx_disable_ati_bug);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4391,
Signature · 1 line
2.35.1
#1 lore raw
Quoted 4 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI devices")

This is interesting because there must be a TON of these AMD/ATI SB600 USB devices in the field, and 306c54d0edb6 was merged in July 2020 and appeared in v5.9.

So why would we only get a report now, in February 2022? Is there some change more recent than 306c54d0edb6 that exposed this problem?

Quoted 29 lines
---
 drivers/pci/quirks.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/pci/quirks.c +7 -0
index 65f7f6b0576c..cc6a87a32b62 100644
@@ -3041,6 +3041,13 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
 			PCI_DEVICE_ID_TIGON3_5715S,
 			quirk_msi_intx_disable_bug);
 
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4386, quirk_msi_intx_disable_bug);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4387, quirk_msi_intx_disable_bug);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4388, quirk_msi_intx_disable_bug);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4389, quirk_msi_intx_disable_bug);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438a, quirk_msi_intx_disable_bug);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438b, quirk_msi_intx_disable_bug);
+
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4390,
 			quirk_msi_intx_disable_ati_bug);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4391,
Signature · 1 line
2.35.1
#2 lore raw
Quoted 4 lines · Bjorn Helgaas
Quoted 3 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Quoted 8 lines
Quoted 1 line
Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI devices")

This is interesting because there must be a TON of these AMD/ATI SB600 USB devices in the field, and 306c54d0edb6 was merged in July 2020 and appeared in v5.9.

So why would we only get a report now, in February 2022? Is there some change more recent than 306c54d0edb6 that exposed this problem?

I think it's a rhetorical question. To me it's as simple as the latency between getting the change into the kernel.

However, I'm a bit worried that in case of ATI there are not so many platforms that are kept up-to-dated.

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#3 lore raw
Quoted 11 lines · Andy Shevchenko
Quoted 10 lines · Bjorn Helgaas
Quoted 4 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI devices")

This is interesting because there must be a TON of these AMD/ATI SB600 USB devices in the field, and 306c54d0edb6 was merged in July 2020 and appeared in v5.9.

Quoted 8 lines
Quoted 2 lines

So why would we only get a report now, in February 2022? Is there some change more recent than 306c54d0edb6 that exposed this problem?

I think it's a rhetorical question. To me it's as simple as the latency between getting the change into the kernel.

However, I'm a bit worried that in case of ATI there are not so many platforms that are kept up-to-dated.

This would be a rhetorical question if I were not interested in the answer but asking only to make a point. That's not the case at all.

If these SB600 USB devices stopped working in v5.9 (October 2020), that would affect lots of keyboards and mice, and I would be surprised if we didn't hear about it until February, 2022.

I looked through https://github.com/linuxhw/Dmesg, and there are at least 40 dmesg logs from v5.9 or later with SB600 USB, so I'm still a little skeptical that 306c54d0edb6 by itself is enough to explain this.

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

PCI: Disable broken MSI on ATI SB600 USB adapters

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

#4 lore raw
Quoted 33 lines · Bjorn Helgaas
Quoted 11 lines · Andy Shevchenko
Quoted 10 lines · Bjorn Helgaas
Quoted 4 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI devices")

This is interesting because there must be a TON of these AMD/ATI SB600 USB devices in the field, and 306c54d0edb6 was merged in July 2020 and appeared in v5.9.

Quoted 8 lines
Quoted 2 lines

So why would we only get a report now, in February 2022? Is there some change more recent than 306c54d0edb6 that exposed this problem?

I think it's a rhetorical question. To me it's as simple as the latency between getting the change into the kernel.

However, I'm a bit worried that in case of ATI there are not so many platforms that are kept up-to-dated.

This would be a rhetorical question if I were not interested in the answer but asking only to make a point. That's not the case at all.

If these SB600 USB devices stopped working in v5.9 (October 2020), that would affect lots of keyboards and mice, and I would be surprised if we didn't hear about it until February, 2022.

I looked through https://github.com/linuxhw/Dmesg, and there are at least 40 dmesg logs from v5.9 or later with SB600 USB, so I'm still a little skeptical that 306c54d0edb6 by itself is enough to explain this.

Quoted 7 lines

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

PCI: Disable broken MSI on ATI SB600 USB adapters

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

But IIUC MSI is _not_ disabled. That's why I have issued this version of the patch with different commit message. Did I misunderstand something?

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#5 lore raw
Quoted 37 lines · Andy Shevchenko
Quoted 36 lines · Bjorn Helgaas
Quoted 11 lines · Andy Shevchenko
Quoted 10 lines · Bjorn Helgaas
Quoted 4 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI devices")

This is interesting because there must be a TON of these AMD/ATI SB600 USB devices in the field, and 306c54d0edb6 was merged in July 2020 and appeared in v5.9.

Quoted 8 lines
Quoted 2 lines

So why would we only get a report now, in February 2022? Is there some change more recent than 306c54d0edb6 that exposed this problem?

I think it's a rhetorical question. To me it's as simple as the latency between getting the change into the kernel.

However, I'm a bit worried that in case of ATI there are not so many platforms that are kept up-to-dated.

This would be a rhetorical question if I were not interested in the answer but asking only to make a point. That's not the case at all.

If these SB600 USB devices stopped working in v5.9 (October 2020), that would affect lots of keyboards and mice, and I would be surprised if we didn't hear about it until February, 2022.

I looked through https://github.com/linuxhw/Dmesg, and there are at least 40 dmesg logs from v5.9 or later with SB600 USB, so I'm still a little skeptical that 306c54d0edb6 by itself is enough to explain this.

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

Quoted 7 lines
Quoted 4 lines

PCI: Disable broken MSI on ATI SB600 USB adapters

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

But IIUC MSI is _not_ disabled. That's why I have issued this version of the patch with different commit message. Did I misunderstand something?

Oh, right, of course. Sorry, I was asleep at the wheel.

I guess it's just that for these devices, we don't disable INTx when enabling MSI. I can't remember why we disable INTx when enabling MSI, but it raises the question of whether it's better to leave INTx enabled or to just disable use of MSI completely.

Bjorn

#6 lore raw
Quoted 40 lines · Bjorn Helgaas
Quoted 39 lines · Andy Shevchenko
Quoted 38 lines · Bjorn Helgaas
Quoted 11 lines · Andy Shevchenko
Quoted 10 lines · Bjorn Helgaas
Quoted 4 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI devices")

This is interesting because there must be a TON of these AMD/ATI SB600 USB devices in the field, and 306c54d0edb6 was merged in July 2020 and appeared in v5.9.

Quoted 8 lines
Quoted 2 lines

So why would we only get a report now, in February 2022? Is there some change more recent than 306c54d0edb6 that exposed this problem?

I think it's a rhetorical question. To me it's as simple as the latency between getting the change into the kernel.

However, I'm a bit worried that in case of ATI there are not so many platforms that are kept up-to-dated.

This would be a rhetorical question if I were not interested in the answer but asking only to make a point. That's not the case at all.

If these SB600 USB devices stopped working in v5.9 (October 2020), that would affect lots of keyboards and mice, and I would be surprised if we didn't hear about it until February, 2022.

I looked through https://github.com/linuxhw/Dmesg, and there are at least 40 dmesg logs from v5.9 or later with SB600 USB, so I'm still a little skeptical that 306c54d0edb6 by itself is enough to explain this.

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

PCI: Disable broken MSI on ATI SB600 USB adapters

Quoted 7 lines
Quoted 5 lines
Quoted 2 lines

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

But IIUC MSI is _not_ disabled. That's why I have issued this version of the patch with different commit message. Did I misunderstand something?

Oh, right, of course. Sorry, I was asleep at the wheel.

Are you going to fix that?

Quoted 4 lines

I guess it's just that for these devices, we don't disable INTx when enabling MSI. I can't remember why we disable INTx when enabling MSI, but it raises the question of whether it's better to leave INTx enabled or to just disable use of MSI completely.

It's required by specification to disable INTx if I read 6.1.4.3 Enabling Operation correctly.

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#7 lore raw

[+cc Alex]

Quoted 21 lines · Andy Shevchenko
Quoted 20 lines · Bjorn Helgaas
Quoted 19 lines · Andy Shevchenko
Quoted 17 lines · Bjorn Helgaas
Quoted 8 lines · Andy Shevchenko
Quoted 7 lines · Bjorn Helgaas
Quoted 6 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on

PCI devices")

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

PCI: Disable broken MSI on ATI SB600 USB adapters

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

Quoted 7 lines
Quoted 5 lines
Quoted 3 lines

But IIUC MSI is _not_ disabled. That's why I have issued this version of the patch with different commit message. Did I misunderstand something?

Oh, right, of course. Sorry, I was asleep at the wheel.

Are you going to fix that?

Yes, of course, I'll do something with the commit message after we figure out how to handle PCI_COMMAND_INTX_DISABLE.

Quoted 7 lines
Quoted 4 lines

I guess it's just that for these devices, we don't disable INTx when enabling MSI. I can't remember why we disable INTx when enabling MSI, but it raises the question of whether it's better to leave INTx enabled or to just disable use of MSI completely.

It's required by specification to disable INTx if I read 6.1.4.3 Enabling Operation correctly.

Thanks for the reference; I was looking for something like that. But I don't think this section requires us to set PCI_COMMAND_INTX_DISABLE. For the benefit of folks without the spec, PCIe r6.0, sec 6.1.4.3 says:

To maintain backward compatibility, the MSI Enable bit in the Message Control Register for MSI and the MSI-X Enable bit in the Message Control Register for MSI-X are each Clear by default (MSI and MSI-X are both disabled). System configuration software Sets one of these bits to enable either MSI or MSI-X, but never both simultaneously. Behavior is undefined if both MSI and MSI-X are enabled simultaneously. Software disabling either mechanism during active operation may result in the Function dropping pending interrupt conditions or failing to recognize new interrupt conditions. While enabled for MSI or MSI-X operation, a Function is prohibited from using INTx interrupts (if implemented) to request service (MSI, MSI-X, and INTx are mutually exclusive).

The only *software* constraints I see are (1) software must never enable both MSI and MSI-X simultaneously, and (2) if software disables MSI or MSI-X during active operation, the Function may fail to generate an interrupt when it should.

I read the last sentence as a constraint on the *hardware*: if either MSI or MSI-X is enabled, the Function is not allowed to use INTx, regardless of the state of PCI_COMMAND_INTX_DISABLE.

I searched the spec for "Interrupt Disable", looking for situations where software might be *required* to set it, but I didn't see anything.

I suspect "Interrupt Disable" was intended to help the OS stop all activity from a device during hot-plug or reconfiguration, as hinted at in sec 6.4, "Device Synchronization":

The ability of the driver and/or system software to block new Requests from the device is supported by the Bus Master Enable, SERR# Enable, and Interrupt Disable bits in the Command register (Section 7.5.1.1.3) of each device Function, and other such control bits.

So I'm trying to figure out why when enabling MSI we need to set PCI_COMMAND_INTX_DISABLE for most devices, but it's safe to skip that for these quirked devices.

Bjorn

#8 lore raw
Quoted 84 lines · On Wed, 16 Mar 2022 16:15:48 -0500 Bjorn Helgaas <[email protected]> wrote:

[+cc Alex]

Quoted 21 lines · Andy Shevchenko
Quoted 20 lines · Bjorn Helgaas
Quoted 19 lines · Andy Shevchenko
Quoted 17 lines · Bjorn Helgaas
Quoted 8 lines · Andy Shevchenko
Quoted 7 lines · Bjorn Helgaas
Quoted 6 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on

PCI devices")

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

PCI: Disable broken MSI on ATI SB600 USB adapters

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

Quoted 7 lines
Quoted 5 lines
Quoted 3 lines

But IIUC MSI is _not_ disabled. That's why I have issued this version of the patch with different commit message. Did I misunderstand something?

Oh, right, of course. Sorry, I was asleep at the wheel.

Are you going to fix that?

Yes, of course, I'll do something with the commit message after we figure out how to handle PCI_COMMAND_INTX_DISABLE.

Quoted 7 lines
Quoted 4 lines

I guess it's just that for these devices, we don't disable INTx when enabling MSI. I can't remember why we disable INTx when enabling MSI, but it raises the question of whether it's better to leave INTx enabled or to just disable use of MSI completely.

It's required by specification to disable INTx if I read 6.1.4.3 Enabling Operation correctly.

Thanks for the reference; I was looking for something like that. But I don't think this section requires us to set PCI_COMMAND_INTX_DISABLE. For the benefit of folks without the spec, PCIe r6.0, sec 6.1.4.3 says:

To maintain backward compatibility, the MSI Enable bit in the Message Control Register for MSI and the MSI-X Enable bit in the Message Control Register for MSI-X are each Clear by default (MSI and MSI-X are both disabled). System configuration software Sets one of these bits to enable either MSI or MSI-X, but never both simultaneously. Behavior is undefined if both MSI and MSI-X are enabled simultaneously. Software disabling either mechanism during active operation may result in the Function dropping pending interrupt conditions or failing to recognize new interrupt conditions. While enabled for MSI or MSI-X operation, a Function is prohibited from using INTx interrupts (if implemented) to request service (MSI, MSI-X, and INTx are mutually exclusive).

The only *software* constraints I see are (1) software must never enable both MSI and MSI-X simultaneously, and (2) if software disables MSI or MSI-X during active operation, the Function may fail to generate an interrupt when it should.

I read the last sentence as a constraint on the *hardware*: if either MSI or MSI-X is enabled, the Function is not allowed to use INTx, regardless of the state of PCI_COMMAND_INTX_DISABLE.

I searched the spec for "Interrupt Disable", looking for situations where software might be *required* to set it, but I didn't see anything.

I suspect "Interrupt Disable" was intended to help the OS stop all activity from a device during hot-plug or reconfiguration, as hinted at in sec 6.4, "Device Synchronization":

The ability of the driver and/or system software to block new Requests from the device is supported by the Bus Master Enable, SERR# Enable, and Interrupt Disable bits in the Command register (Section 7.5.1.1.3) of each device Function, and other such control bits.

Quoted 3 lines

So I'm trying to figure out why when enabling MSI we need to set PCI_COMMAND_INTX_DISABLE for most devices, but it's safe to skip that for these quirked devices.

I don't have an authoritative answer, but in the conventional PCI 2.3 spec the bit definitions for DisINTx and MSI Enable cross reference each other from which one might infer a symmetry that we disable one to use the other. In PCIe INTx becomes a virtual wire interrupt and there the DisINTx bit definition states that setting this bit requires the device to issue the de-assert message for that virtual wire, so there might be some FUD relative to enabling MSI/X while the device has already asserted INTx.

At best though, I don't know of anything to support that setting DisINTx should have any effect on MSI/X, that much seems like it is certainly a hardware bug. Thanks,

Alex

#9 lore raw
In reply to Bjorn Helgaas
Quoted 82 lines · Bjorn Helgaas
Quoted 21 lines · Andy Shevchenko
Quoted 20 lines · Bjorn Helgaas
Quoted 19 lines · Andy Shevchenko
Quoted 17 lines · Bjorn Helgaas
Quoted 8 lines · Andy Shevchenko
Quoted 7 lines · Bjorn Helgaas
Quoted 6 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on

PCI devices")

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

PCI: Disable broken MSI on ATI SB600 USB adapters

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

Quoted 7 lines
Quoted 5 lines
Quoted 3 lines

But IIUC MSI is _not_ disabled. That's why I have issued this version of the patch with different commit message. Did I misunderstand something?

Oh, right, of course. Sorry, I was asleep at the wheel.

Are you going to fix that?

Yes, of course, I'll do something with the commit message after we figure out how to handle PCI_COMMAND_INTX_DISABLE.

Quoted 7 lines
Quoted 4 lines

I guess it's just that for these devices, we don't disable INTx when enabling MSI. I can't remember why we disable INTx when enabling MSI, but it raises the question of whether it's better to leave INTx enabled or to just disable use of MSI completely.

It's required by specification to disable INTx if I read 6.1.4.3 Enabling Operation correctly.

Thanks for the reference; I was looking for something like that. But I don't think this section requires us to set PCI_COMMAND_INTX_DISABLE. For the benefit of folks without the spec, PCIe r6.0, sec 6.1.4.3 says:

To maintain backward compatibility, the MSI Enable bit in the Message Control Register for MSI and the MSI-X Enable bit in the Message Control Register for MSI-X are each Clear by default (MSI and MSI-X are both disabled). System configuration software Sets one of these bits to enable either MSI or MSI-X, but never both simultaneously. Behavior is undefined if both MSI and MSI-X are enabled simultaneously. Software disabling either mechanism during active operation may result in the Function dropping pending interrupt conditions or failing to recognize new interrupt conditions. While enabled for MSI or MSI-X operation, a Function is prohibited from using INTx interrupts (if implemented) to request service (MSI, MSI-X, and INTx are mutually exclusive).

The only *software* constraints I see are (1) software must never enable both MSI and MSI-X simultaneously, and (2) if software disables MSI or MSI-X during active operation, the Function may fail to generate an interrupt when it should.

I read the last sentence as a constraint on the *hardware*: if either MSI or MSI-X is enabled, the Function is not allowed to use INTx, regardless of the state of PCI_COMMAND_INTX_DISABLE.

I searched the spec for "Interrupt Disable", looking for situations where software might be *required* to set it, but I didn't see anything.

I suspect "Interrupt Disable" was intended to help the OS stop all activity from a device during hot-plug or reconfiguration, as hinted at in sec 6.4, "Device Synchronization":

The ability of the driver and/or system software to block new Requests from the device is supported by the Bus Master Enable, SERR# Enable, and Interrupt Disable bits in the Command register (Section 7.5.1.1.3) of each device Function, and other such control bits.

Quoted 3 lines

So I'm trying to figure out why when enabling MSI we need to set PCI_COMMAND_INTX_DISABLE for most devices, but it's safe to skip that for these quirked devices.

I guess it's wrong wording in the last paragraph. It's not safe, but it's _required_ since HW doesn't follow PCI specification that clearly says:
"MSI, MSI-X, and INTx are mutually exclusive".

This is also supported by the other devices on the same chipset doing that and by the reported of the issue.

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#10 lore raw
Quoted 83 lines · Andy Shevchenko
Quoted 82 lines · Bjorn Helgaas
Quoted 21 lines · Andy Shevchenko
Quoted 20 lines · Bjorn Helgaas
Quoted 19 lines · Andy Shevchenko
Quoted 17 lines · Bjorn Helgaas
Quoted 8 lines · Andy Shevchenko
Quoted 7 lines · Bjorn Helgaas
Quoted 6 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on

PCI devices")

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

PCI: Disable broken MSI on ATI SB600 USB adapters

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

Quoted 7 lines
Quoted 5 lines
Quoted 3 lines

But IIUC MSI is _not_ disabled. That's why I have issued this version of the patch with different commit message. Did I misunderstand something?

Oh, right, of course. Sorry, I was asleep at the wheel.

Are you going to fix that?

Yes, of course, I'll do something with the commit message after we figure out how to handle PCI_COMMAND_INTX_DISABLE.

Quoted 7 lines
Quoted 4 lines

I guess it's just that for these devices, we don't disable INTx when enabling MSI. I can't remember why we disable INTx when enabling MSI, but it raises the question of whether it's better to leave INTx enabled or to just disable use of MSI completely.

It's required by specification to disable INTx if I read 6.1.4.3 Enabling Operation correctly.

Thanks for the reference; I was looking for something like that. But I don't think this section requires us to set PCI_COMMAND_INTX_DISABLE. For the benefit of folks without the spec, PCIe r6.0, sec 6.1.4.3 says:

To maintain backward compatibility, the MSI Enable bit in the Message Control Register for MSI and the MSI-X Enable bit in the Message Control Register for MSI-X are each Clear by default (MSI and MSI-X are both disabled). System configuration software Sets one of these bits to enable either MSI or MSI-X, but never both simultaneously. Behavior is undefined if both MSI and MSI-X are enabled simultaneously. Software disabling either mechanism during active operation may result in the Function dropping pending interrupt conditions or failing to recognize new interrupt conditions. While enabled for MSI or MSI-X operation, a Function is prohibited from using INTx interrupts (if implemented) to request service (MSI, MSI-X, and INTx are mutually exclusive).

The only *software* constraints I see are (1) software must never enable both MSI and MSI-X simultaneously, and (2) if software disables MSI or MSI-X during active operation, the Function may fail to generate an interrupt when it should.

I read the last sentence as a constraint on the *hardware*: if either MSI or MSI-X is enabled, the Function is not allowed to use INTx, regardless of the state of PCI_COMMAND_INTX_DISABLE.

I searched the spec for "Interrupt Disable", looking for situations where software might be *required* to set it, but I didn't see anything.

I suspect "Interrupt Disable" was intended to help the OS stop all activity from a device during hot-plug or reconfiguration, as hinted at in sec 6.4, "Device Synchronization":

The ability of the driver and/or system software to block new Requests from the device is supported by the Bus Master Enable, SERR# Enable, and Interrupt Disable bits in the Command register (Section 7.5.1.1.3) of each device Function, and other such control bits.

Quoted 7 lines
Quoted 3 lines

So I'm trying to figure out why when enabling MSI we need to set PCI_COMMAND_INTX_DISABLE for most devices, but it's safe to skip that for these quirked devices.

I guess it's wrong wording in the last paragraph. It's not safe, but it's _required_ since HW doesn't follow PCI specification that clearly says:
"MSI, MSI-X, and INTx are mutually exclusive".

I agree there's a defect in these SB600 devices. My guess is that PCI_COMMAND_INTX_DISABLE actually disables both INTx and MSI, when it's only supposed to disable INTx.

I'm pretty sure the spec doesn't actually require software to set Interrupt Disable when enabling MSI, since MSI was added in PCI r2.2, which included this text in sec 6.8.2:

System configuration software sets [the MSI Enable] bit to enable MSI. ... Once enabled, a function is prohibited from using its INTx# pin (if implemented) to request service (MSI and INTx# are mutually exclusive).

and Interrupt Disable was added later, in PCI r2.3, with no mention of a connection with MSI. All the specs from PCI r2.2 to PCIe r6.0 include the text above about not using INTx# if MSI or MSI-X is enabled, but that's not the same as requiring software to set Interrupt Disable. Linux has set Interrupt Disable when enabling MSI ever since MSI support was added [1], so I would hesitate to change that even though I don't think it's required.

What I don't like about PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG is that it changes the generic code path in a sort of random way, i.e., this device becomes yet another special case in how we handle Interrupt Disable.

What would you think about just setting pdev->no_msi instead, so we don't try to use MSI at all on these devices? I think that's what we did before 306c54d0edb6.

[1] https://lore.kernel.org/all/[email protected]/ (search for PCI_COMMAND_INTX_DISABLE)

#11 lore raw
Quoted 105 lines · Bjorn Helgaas
Quoted 83 lines · Andy Shevchenko
Quoted 82 lines · Bjorn Helgaas
Quoted 21 lines · Andy Shevchenko
Quoted 20 lines · Bjorn Helgaas
Quoted 19 lines · Andy Shevchenko
Quoted 17 lines · Bjorn Helgaas
Quoted 8 lines · Andy Shevchenko
Quoted 7 lines · Bjorn Helgaas
Quoted 6 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on

PCI devices")

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

PCI: Disable broken MSI on ATI SB600 USB adapters

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

Quoted 7 lines
Quoted 5 lines
Quoted 3 lines

But IIUC MSI is _not_ disabled. That's why I have issued this version of the patch with different commit message. Did I misunderstand something?

Oh, right, of course. Sorry, I was asleep at the wheel.

Are you going to fix that?

Yes, of course, I'll do something with the commit message after we figure out how to handle PCI_COMMAND_INTX_DISABLE.

Quoted 7 lines
Quoted 4 lines

I guess it's just that for these devices, we don't disable INTx when enabling MSI. I can't remember why we disable INTx when enabling MSI, but it raises the question of whether it's better to leave INTx enabled or to just disable use of MSI completely.

It's required by specification to disable INTx if I read 6.1.4.3 Enabling Operation correctly.

Thanks for the reference; I was looking for something like that. But I don't think this section requires us to set PCI_COMMAND_INTX_DISABLE. For the benefit of folks without the spec, PCIe r6.0, sec 6.1.4.3 says:

To maintain backward compatibility, the MSI Enable bit in the Message Control Register for MSI and the MSI-X Enable bit in the Message Control Register for MSI-X are each Clear by default (MSI and MSI-X are both disabled). System configuration software Sets one of these bits to enable either MSI or MSI-X, but never both simultaneously. Behavior is undefined if both MSI and MSI-X are enabled simultaneously. Software disabling either mechanism during active operation may result in the Function dropping pending interrupt conditions or failing to recognize new interrupt conditions. While enabled for MSI or MSI-X operation, a Function is prohibited from using INTx interrupts (if implemented) to request service (MSI, MSI-X, and INTx are mutually exclusive).

The only *software* constraints I see are (1) software must never enable both MSI and MSI-X simultaneously, and (2) if software disables MSI or MSI-X during active operation, the Function may fail to generate an interrupt when it should.

I read the last sentence as a constraint on the *hardware*: if either MSI or MSI-X is enabled, the Function is not allowed to use INTx, regardless of the state of PCI_COMMAND_INTX_DISABLE.

I searched the spec for "Interrupt Disable", looking for situations where software might be *required* to set it, but I didn't see anything.

I suspect "Interrupt Disable" was intended to help the OS stop all activity from a device during hot-plug or reconfiguration, as hinted at in sec 6.4, "Device Synchronization":

The ability of the driver and/or system software to block new Requests from the device is supported by the Bus Master Enable, SERR# Enable, and Interrupt Disable bits in the Command register (Section 7.5.1.1.3) of each device Function, and other such control bits.

Quoted 7 lines
Quoted 3 lines

So I'm trying to figure out why when enabling MSI we need to set PCI_COMMAND_INTX_DISABLE for most devices, but it's safe to skip that for these quirked devices.

I guess it's wrong wording in the last paragraph. It's not safe, but it's _required_ since HW doesn't follow PCI specification that clearly says:
"MSI, MSI-X, and INTx are mutually exclusive".

I agree there's a defect in these SB600 devices. My guess is that PCI_COMMAND_INTX_DISABLE actually disables both INTx and MSI, when it's only supposed to disable INTx.

I'm pretty sure the spec doesn't actually require software to set Interrupt Disable when enabling MSI, since MSI was added in PCI r2.2, which included this text in sec 6.8.2:

System configuration software sets [the MSI Enable] bit to enable MSI. ... Once enabled, a function is prohibited from using its INTx# pin (if implemented) to request service (MSI and INTx# are mutually exclusive).

Quoted 7 lines

and Interrupt Disable was added later, in PCI r2.3, with no mention of a connection with MSI. All the specs from PCI r2.2 to PCIe r6.0 include the text above about not using INTx# if MSI or MSI-X is enabled, but that's not the same as requiring software to set Interrupt Disable. Linux has set Interrupt Disable when enabling MSI ever since MSI support was added [1], so I would hesitate to change that even though I don't think it's required.

Thanks for diving into the history of the specification. What I learnt about any of the specifications is that it usually has a lot of implications that are only understandable (known) to the specification author(s). This gives a room of misinterpretation. In any case I usually apply my common sense denominator, so I try to go with the straight logic. In this case it seems to me that keeping both enabled is illogical and Linux does the right thing (means the author of the Linux kernel implementation is on the same page with me).

Quoted 8 lines

What I don't like about PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG is that it changes the generic code path in a sort of random way, i.e., this device becomes yet another special case in how we handle Interrupt Disable.

What would you think about just setting pdev->no_msi instead, so we don't try to use MSI at all on these devices? I think that's what we did before 306c54d0edb6.

Yes, we did. But why should we go this way if it already established a special case disregarding my patch(es)? If you want to do that you need to explain why other devices on the same chipset should enable MSI and what's wrong with enabling MSI on the USB devices. My understanding is that the MSI is a good thing to have due to performance benefits and taking into account other devices that have already been using it on the other devices of the same chipset tells me that's okay. Moreover, the reporter of the bug confirmed that MSI works for them after applying this quirk fix.

Quoted 1 line

[1] https://lore.kernel.org/all/[email protected]/ (search for PCI_COMMAND_INTX_DISABLE)

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#12 lore raw
Quoted 132 lines · Andy Shevchenko
Quoted 105 lines · Bjorn Helgaas
Quoted 83 lines · Andy Shevchenko
Quoted 82 lines · Bjorn Helgaas
Quoted 21 lines · Andy Shevchenko
Quoted 20 lines · Bjorn Helgaas
Quoted 19 lines · Andy Shevchenko
Quoted 17 lines · Bjorn Helgaas
Quoted 8 lines · Andy Shevchenko
Quoted 7 lines · Bjorn Helgaas
Quoted 6 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on

PCI devices")

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

PCI: Disable broken MSI on ATI SB600 USB adapters

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

Quoted 7 lines
Quoted 5 lines
Quoted 3 lines

But IIUC MSI is _not_ disabled. That's why I have issued this version of the patch with different commit message. Did I misunderstand something?

Oh, right, of course. Sorry, I was asleep at the wheel.

Are you going to fix that?

Yes, of course, I'll do something with the commit message after we figure out how to handle PCI_COMMAND_INTX_DISABLE.

Quoted 7 lines
Quoted 4 lines

I guess it's just that for these devices, we don't disable INTx when enabling MSI. I can't remember why we disable INTx when enabling MSI, but it raises the question of whether it's better to leave INTx enabled or to just disable use of MSI completely.

It's required by specification to disable INTx if I read 6.1.4.3 Enabling Operation correctly.

Thanks for the reference; I was looking for something like that. But I don't think this section requires us to set PCI_COMMAND_INTX_DISABLE. For the benefit of folks without the spec, PCIe r6.0, sec 6.1.4.3 says:

To maintain backward compatibility, the MSI Enable bit in the Message Control Register for MSI and the MSI-X Enable bit in the Message Control Register for MSI-X are each Clear by default (MSI and MSI-X are both disabled). System configuration software Sets one of these bits to enable either MSI or MSI-X, but never both simultaneously. Behavior is undefined if both MSI and MSI-X are enabled simultaneously. Software disabling either mechanism during active operation may result in the Function dropping pending interrupt conditions or failing to recognize new interrupt conditions. While enabled for MSI or MSI-X operation, a Function is prohibited from using INTx interrupts (if implemented) to request service (MSI, MSI-X, and INTx are mutually exclusive).

The only *software* constraints I see are (1) software must never enable both MSI and MSI-X simultaneously, and (2) if software disables MSI or MSI-X during active operation, the Function may fail to generate an interrupt when it should.

I read the last sentence as a constraint on the *hardware*: if either MSI or MSI-X is enabled, the Function is not allowed to use INTx, regardless of the state of PCI_COMMAND_INTX_DISABLE.

I searched the spec for "Interrupt Disable", looking for situations where software might be *required* to set it, but I didn't see anything.

I suspect "Interrupt Disable" was intended to help the OS stop all activity from a device during hot-plug or reconfiguration, as hinted at in sec 6.4, "Device Synchronization":

The ability of the driver and/or system software to block new Requests from the device is supported by the Bus Master Enable, SERR# Enable, and Interrupt Disable bits in the Command register (Section 7.5.1.1.3) of each device Function, and other such control bits.

Quoted 7 lines
Quoted 3 lines

So I'm trying to figure out why when enabling MSI we need to set PCI_COMMAND_INTX_DISABLE for most devices, but it's safe to skip that for these quirked devices.

I guess it's wrong wording in the last paragraph. It's not safe, but it's _required_ since HW doesn't follow PCI specification that clearly says:
"MSI, MSI-X, and INTx are mutually exclusive".

I agree there's a defect in these SB600 devices. My guess is that PCI_COMMAND_INTX_DISABLE actually disables both INTx and MSI, when it's only supposed to disable INTx.

I'm pretty sure the spec doesn't actually require software to set Interrupt Disable when enabling MSI, since MSI was added in PCI r2.2, which included this text in sec 6.8.2:

System configuration software sets [the MSI Enable] bit to enable MSI. ... Once enabled, a function is prohibited from using its INTx# pin (if implemented) to request service (MSI and INTx# are mutually exclusive).

Quoted 7 lines

and Interrupt Disable was added later, in PCI r2.3, with no mention of a connection with MSI. All the specs from PCI r2.2 to PCIe r6.0 include the text above about not using INTx# if MSI or MSI-X is enabled, but that's not the same as requiring software to set Interrupt Disable. Linux has set Interrupt Disable when enabling MSI ever since MSI support was added [1], so I would hesitate to change that even though I don't think it's required.

Thanks for diving into the history of the specification. What I learnt about any of the specifications is that it usually has a lot of implications that are only understandable (known) to the specification author(s). This gives a room of misinterpretation. In any case I usually apply my common sense denominator, so I try to go with the straight logic. In this case it seems to me that keeping both enabled is illogical and Linux does the right thing (means the author of the Linux kernel implementation is on the same page with me).

Quoted 8 lines

What I don't like about PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG is that it changes the generic code path in a sort of random way, i.e., this device becomes yet another special case in how we handle Interrupt Disable.

What would you think about just setting pdev->no_msi instead, so we don't try to use MSI at all on these devices? I think that's what we did before 306c54d0edb6.

Quoted 9 lines

Yes, we did. But why should we go this way if it already established a special case disregarding my patch(es)? If you want to do that you need to explain why other devices on the same chipset should enable MSI and what's wrong with enabling MSI on the USB devices. My understanding is that the MSI is a good thing to have due to performance benefits and taking into account other devices that have already been using it on the other devices of the same chipset tells me that's okay. Moreover, the reporter of the bug confirmed that MSI works for them after applying this quirk fix.

I agree that MSI is generally to be preferred over INTx. In this case, it's an old USB device and I don't think there's any real performance benefit.

The problem with enabling MSI on these USB devices is that the generic MSI code doesn't work correctly. Since we've been using them without MSI in the past, and they have some defect that makes MSI not work correctly, it seems like the simplest solution is to avoid using MSI, something like the patch below.

Would I prefer the same for all the other existing users of PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG? Yes. Enough to change the status quo, which would be a performance regression, and potentially break something? Probably not.

drivers/pci/quirks.c +12 -0
index d2dd6a6cda60..c0e6b031bb5d 100644
@@ -2675,6 +2675,18 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS,
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE,
 			 ht_enable_msi_mapping);
 
+static void quirk_no_msi(struct pci_dev *dev)
+{
+	pci_info(dev, "Disabling MSI to avoid hardware defect\n");
+	dev->no_msi = 1;
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4386, quirk_no_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4387, quirk_no_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4388, quirk_no_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4389, quirk_no_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438a, quirk_no_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438b, quirk_no_msi);
+
 /*
  * The P5N32-SLI motherboards from Asus have a problem with MSI
  * for the MCP55 NIC. It is not yet determined whether the MSI problem
#13 lore raw
Quoted 143 lines · Bjorn Helgaas
Quoted 132 lines · Andy Shevchenko
Quoted 105 lines · Bjorn Helgaas
Quoted 83 lines · Andy Shevchenko
Quoted 82 lines · Bjorn Helgaas
Quoted 21 lines · Andy Shevchenko
Quoted 20 lines · Bjorn Helgaas
Quoted 19 lines · Andy Shevchenko
Quoted 17 lines · Bjorn Helgaas
Quoted 8 lines · Andy Shevchenko
Quoted 7 lines · Bjorn Helgaas
Quoted 6 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work if INTx is disabled. Enable the respective quirk as it's done for other ATI devices on this chipset,

Fixes 306c54d0edb6 ("usb: hcd: Try MSI interrupts on

PCI devices")

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

PCI: Disable broken MSI on ATI SB600 USB adapters

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

Quoted 7 lines
Quoted 5 lines
Quoted 3 lines

But IIUC MSI is _not_ disabled. That's why I have issued this version of the patch with different commit message. Did I misunderstand something?

Oh, right, of course. Sorry, I was asleep at the wheel.

Are you going to fix that?

Yes, of course, I'll do something with the commit message after we figure out how to handle PCI_COMMAND_INTX_DISABLE.

Quoted 7 lines
Quoted 4 lines

I guess it's just that for these devices, we don't disable INTx when enabling MSI. I can't remember why we disable INTx when enabling MSI, but it raises the question of whether it's better to leave INTx enabled or to just disable use of MSI completely.

It's required by specification to disable INTx if I read 6.1.4.3 Enabling Operation correctly.

Thanks for the reference; I was looking for something like that. But I don't think this section requires us to set PCI_COMMAND_INTX_DISABLE. For the benefit of folks without the spec, PCIe r6.0, sec 6.1.4.3 says:

To maintain backward compatibility, the MSI Enable bit in the Message Control Register for MSI and the MSI-X Enable bit in the Message Control Register for MSI-X are each Clear by default (MSI and MSI-X are both disabled). System configuration software Sets one of these bits to enable either MSI or MSI-X, but never both simultaneously. Behavior is undefined if both MSI and MSI-X are enabled simultaneously. Software disabling either mechanism during active operation may result in the Function dropping pending interrupt conditions or failing to recognize new interrupt conditions. While enabled for MSI or MSI-X operation, a Function is prohibited from using INTx interrupts (if implemented) to request service (MSI, MSI-X, and INTx are mutually exclusive).

The only *software* constraints I see are (1) software must never enable both MSI and MSI-X simultaneously, and (2) if software disables MSI or MSI-X during active operation, the Function may fail to generate an interrupt when it should.

I read the last sentence as a constraint on the *hardware*: if either MSI or MSI-X is enabled, the Function is not allowed to use INTx, regardless of the state of PCI_COMMAND_INTX_DISABLE.

I searched the spec for "Interrupt Disable", looking for situations where software might be *required* to set it, but I didn't see anything.

I suspect "Interrupt Disable" was intended to help the OS stop all activity from a device during hot-plug or reconfiguration, as hinted at in sec 6.4, "Device Synchronization":

The ability of the driver and/or system software to block new Requests from the device is supported by the Bus Master Enable, SERR# Enable, and Interrupt Disable bits in the Command register (Section 7.5.1.1.3) of each device Function, and other such control bits.

Quoted 7 lines
Quoted 3 lines

So I'm trying to figure out why when enabling MSI we need to set PCI_COMMAND_INTX_DISABLE for most devices, but it's safe to skip that for these quirked devices.

I guess it's wrong wording in the last paragraph. It's not safe, but it's _required_ since HW doesn't follow PCI specification that clearly says:
"MSI, MSI-X, and INTx are mutually exclusive".

I agree there's a defect in these SB600 devices. My guess is that PCI_COMMAND_INTX_DISABLE actually disables both INTx and MSI, when it's only supposed to disable INTx.

I'm pretty sure the spec doesn't actually require software to set Interrupt Disable when enabling MSI, since MSI was added in PCI r2.2, which included this text in sec 6.8.2:

System configuration software sets [the MSI Enable] bit to enable MSI. ... Once enabled, a function is prohibited from using its INTx# pin (if implemented) to request service (MSI and INTx# are mutually exclusive).

Quoted 7 lines

and Interrupt Disable was added later, in PCI r2.3, with no mention of a connection with MSI. All the specs from PCI r2.2 to PCIe r6.0 include the text above about not using INTx# if MSI or MSI-X is enabled, but that's not the same as requiring software to set Interrupt Disable. Linux has set Interrupt Disable when enabling MSI ever since MSI support was added [1], so I would hesitate to change that even though I don't think it's required.

Thanks for diving into the history of the specification. What I learnt about any of the specifications is that it usually has a lot of implications that are only understandable (known) to the specification author(s). This gives a room of misinterpretation. In any case I usually apply my common sense denominator, so I try to go with the straight logic. In this case it seems to me that keeping both enabled is illogical and Linux does the right thing (means the author of the Linux kernel implementation is on the same page with me).

Quoted 8 lines

What I don't like about PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG is that it changes the generic code path in a sort of random way, i.e., this device becomes yet another special case in how we handle Interrupt Disable.

What would you think about just setting pdev->no_msi instead, so we don't try to use MSI at all on these devices? I think that's what we did before 306c54d0edb6.

Quoted 9 lines

Yes, we did. But why should we go this way if it already established a special case disregarding my patch(es)? If you want to do that you need to explain why other devices on the same chipset should enable MSI and what's wrong with enabling MSI on the USB devices. My understanding is that the MSI is a good thing to have due to performance benefits and taking into account other devices that have already been using it on the other devices of the same chipset tells me that's okay. Moreover, the reporter of the bug confirmed that MSI works for them after applying this quirk fix.

Quoted 3 lines

I agree that MSI is generally to be preferred over INTx. In this case, it's an old USB device and I don't think there's any real performance benefit.

I tend to disagree. There are not only USB devices involved but other devices that may share the same INTx line(s). This is the case, for example, on EG20T. Dunno if ATI is one of them, but if so, it will support the idea of MSI.

Quoted 2 lines

The problem with enabling MSI on these USB devices is that the generic MSI code doesn't work correctly.

Can you elaborate this, please? Where is that code that doesn't work correctly?

Quoted 4 lines

Since we've been using them without
MSI in the past, and they have some defect that makes MSI not work correctly, it seems like the simplest solution is to avoid using MSI, something like the patch below.

I tend to disagree.

Quoted 4 lines

Would I prefer the same for all the other existing users of PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG? Yes. Enough to change the status quo, which would be a performance regression, and potentially break something? Probably not.

Why? What is the point of deliberate degrading of performance?

...

Let do it simple: Apply my patch since it fixes the regression and move on with whatever solution you may propose latter on. It's really not good for the end-user who was so kind to report and test all this.

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#14 lore raw
Quoted 153 lines · Andy Shevchenko
Quoted 143 lines · Bjorn Helgaas
Quoted 132 lines · Andy Shevchenko
Quoted 105 lines · Bjorn Helgaas
Quoted 83 lines · Andy Shevchenko
Quoted 82 lines · Bjorn Helgaas
Quoted 21 lines · Andy Shevchenko
Quoted 20 lines · Bjorn Helgaas
Quoted 19 lines · Andy Shevchenko
Quoted 17 lines · Bjorn Helgaas
Quoted 8 lines · Andy Shevchenko
Quoted 7 lines · Bjorn Helgaas
Quoted 6 lines · Andy Shevchenko

ATI PCIe-USB adapter advertises MSI, but it doesn't work
if INTx is disabled. Enable the respective quirk as
it's done for other ATI devices on this chipset,

Fixes: 306c54d0edb6 ("usb: hcd: Try MSI interrupts on
PCI devices")

Anyway, I applied this to pci/msi for v5.18 with the following commit log:

PCI: Disable broken MSI on ATI SB600 USB adapters

Some ATI SB600 USB adapters advertise MSI, but MSI doesn't work if INTx is disabled. Disable MSI on these adapters.

Quoted 7 lines
Quoted 5 lines
Quoted 3 lines

But IIUC MSI is _not_ disabled. That's why I have issued this version of the patch with different commit message. Did I misunderstand something?

Oh, right, of course. Sorry, I was asleep at the wheel.

Are you going to fix that?

Yes, of course, I'll do something with the commit message after we figure out how to handle PCI_COMMAND_INTX_DISABLE.

Quoted 7 lines
Quoted 4 lines

I guess it's just that for these devices, we don't disable INTx when enabling MSI. I can't remember why we disable INTx when enabling MSI, but it raises the question of whether it's better to leave INTx enabled or to just disable use of MSI completely.

It's required by specification to disable INTx if I read 6.1.4.3 Enabling Operation correctly.

Thanks for the reference; I was looking for something like that. But I don't think this section requires us to set PCI_COMMAND_INTX_DISABLE. For the benefit of folks without the spec, PCIe r6.0, sec 6.1.4.3 says:

To maintain backward compatibility, the MSI Enable bit in the Message Control Register for MSI and the MSI-X Enable bit in the Message Control Register for MSI-X are each Clear by default (MSI and MSI-X are both disabled). System configuration software Sets one of these bits to enable either MSI or MSI-X, but never both simultaneously. Behavior is undefined if both MSI and MSI-X are enabled simultaneously. Software disabling either mechanism during active operation may result in the Function dropping pending interrupt conditions or failing to recognize new interrupt conditions. While enabled for MSI or MSI-X operation, a Function is prohibited from using INTx interrupts (if implemented) to request service (MSI, MSI-X, and INTx are mutually exclusive).

The only *software* constraints I see are (1) software must never enable both MSI and MSI-X simultaneously, and (2) if software disables MSI or MSI-X during active operation, the Function may fail to generate an interrupt when it should.

I read the last sentence as a constraint on the *hardware*: if either MSI or MSI-X is enabled, the Function is not allowed to use INTx, regardless of the state of PCI_COMMAND_INTX_DISABLE.

I searched the spec for "Interrupt Disable", looking for situations where software might be *required* to set it, but I didn't see anything.

I suspect "Interrupt Disable" was intended to help the OS stop all activity from a device during hot-plug or reconfiguration, as hinted at in sec 6.4, "Device Synchronization":

The ability of the driver and/or system software to block new Requests from the device is supported by the Bus Master Enable, SERR# Enable, and Interrupt Disable bits in the Command register (Section 7.5.1.1.3) of each device Function, and other such control bits.

Quoted 7 lines
Quoted 3 lines

So I'm trying to figure out why when enabling MSI we need to set PCI_COMMAND_INTX_DISABLE for most devices, but it's safe to skip that for these quirked devices.

I guess it's wrong wording in the last paragraph. It's not safe, but it's _required_ since HW doesn't follow PCI specification that clearly says:
"MSI, MSI-X, and INTx are mutually exclusive".

I agree there's a defect in these SB600 devices. My guess is that PCI_COMMAND_INTX_DISABLE actually disables both INTx and MSI, when it's only supposed to disable INTx.

I'm pretty sure the spec doesn't actually require software to set Interrupt Disable when enabling MSI, since MSI was added in PCI r2.2, which included this text in sec 6.8.2:

System configuration software sets [the MSI Enable] bit to enable MSI. ... Once enabled, a function is prohibited from using its INTx# pin (if implemented) to request service (MSI and INTx# are mutually exclusive).

Quoted 7 lines

and Interrupt Disable was added later, in PCI r2.3, with no mention of a connection with MSI. All the specs from PCI r2.2 to PCIe r6.0 include the text above about not using INTx# if MSI or MSI-X is enabled, but that's not the same as requiring software to set Interrupt Disable. Linux has set Interrupt Disable when enabling MSI ever since MSI support was added [1], so I would hesitate to change that even though I don't think it's required.

Thanks for diving into the history of the specification. What I learnt about any of the specifications is that it usually has a lot of implications that are only understandable (known) to the specification author(s). This gives a room of misinterpretation. In any case I usually apply my common sense denominator, so I try to go with the straight logic. In this case it seems to me that keeping both enabled is illogical and Linux does the right thing (means the author of the Linux kernel implementation is on the same page with me).

Quoted 8 lines

What I don't like about PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG is that it changes the generic code path in a sort of random way, i.e., this device becomes yet another special case in how we handle Interrupt Disable.

What would you think about just setting pdev->no_msi instead, so we don't try to use MSI at all on these devices? I think that's what we did before 306c54d0edb6.

Quoted 9 lines

Yes, we did. But why should we go this way if it already established a special case disregarding my patch(es)? If you want to do that you need to explain why other devices on the same chipset should enable MSI and what's wrong with enabling MSI on the USB devices. My understanding is that the MSI is a good thing to have due to performance benefits and taking into account other devices that have already been using it on the other devices of the same chipset tells me that's okay. Moreover, the reporter of the bug confirmed that MSI works for them after applying this quirk fix.

Quoted 3 lines

I agree that MSI is generally to be preferred over INTx. In this case, it's an old USB device and I don't think there's any real performance benefit.

I tend to disagree. There are not only USB devices involved but other devices that may share the same INTx line(s). This is the case, for example, on EG20T. Dunno if ATI is one of them, but if so, it will support the idea of MSI.

Quoted 5 lines
Quoted 2 lines

The problem with enabling MSI on these USB devices is that the generic MSI code doesn't work correctly.

Can you elaborate this, please? Where is that code that doesn't work correctly?

On this device, pci_intx_for_msi() breaks MSI, so if we want to use MSI, we have to set PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG to avoid the breakage.

If a non-essential feature is broken, I think the cleanest path for maintainability is to avoid using the feature. In this case, MSI is broken because Interrupt Disable seems to disable MSI as well as INTx.

If we enable MSI on these devices, we (which really means "I") have to audit all the places that set Interrupt Disable to see if masking both MSI and INTx will break anything. This is the maintainability issue.

Most places that set PCI_COMMAND_INTX_DISABLE are in drivers for other devices, which are not an issue, of course. Some others:

- pci_check_and_mask_intx(): used by vfio_intx_handler() (not a problem since this case uses INTx, not MSI) and the UIO irqhandler() (this is a potential problem for user-space drivers, but I don't know the implications).

- vfio_pci_intx_mask() and similar VFIO paths: potentially an issue, but I guess guest drivers that use these are on their own and have to have their own knowledge of device quirks.

- pci_dev_save_and_disable(): used in reset paths, so shouldn't be an issue.

- xen_pcibk_get_interrupt_type(): decides interrupt type based on reading PCI_COMMAND_INTX_DISABLE and will return "INTERRUPT_TYPE_INTX | INTERRUPT_TYPE_MSI" when it should return "INTERRUPT_TYPE_MSI". Will break msi_msix_flags_write(), which looks for an exact match, but I don't know the further implications.

- Xen command_write(): No idea how to even figure out if this is an issue.

These all look like it *probably* wouldn't seriously break anything to use PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG. But the point is that it's a lot of work for me to even make an educated guess, and "probably safe" and "unknown benefit" don't make a strong case.

Quoted 6 lines
Quoted 4 lines

Would I prefer the same for all the other existing users of PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG? Yes. Enough to change the status quo, which would be a performance regression, and potentially break something? Probably not.

Why? What is the point of deliberate degrading of performance?

Sorry, I didn't make that clear enough. I was trying to say that I don't think it's a good idea to change *existing* users because it would degrade performance and it might break something.

Bjorn