5.15.30-rc1 review

This is the start of the stable review cycle for the 5.15.30 release. There are 25 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sat, 19 Mar 2022 12:45:16 +0000. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

	https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.15.30-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.15.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <[email protected]>

    Linux 5.15.30-rc1

Ivan Vecera <[email protected]>
ice: Fix race condition during interface enslave

Peter Zijlstra <[email protected]>
x86/module: Fix the paravirt vs alternative order

Chengming Zhou <[email protected]>
kselftest/vm: fix tests build with old libc

Christophe JAILLET <[email protected]>
bnx2: Fix an error message

Niels Dossche <[email protected]>

    sfc: extend the locking on mcdi->seqno

Eric Dumazet <[email protected]>
tcp: make tcp_read_sock() more robust

Sreeramya Soratkal <[email protected]>
nl80211: Update bss channel on channel switch for P2P_CLIENT

Manasi Navare <[email protected]>
drm/vrr: Set VRR capable prop only if it is attached to connector

Golan Ben Ami <[email protected]>
iwlwifi: don't advertise TWT support

Jia-Ju Bai <[email protected]>
atm: firestream: check the return value of ioremap() in fs_init()

Lad Prabhakar <[email protected]>
can: rcar_canfd: rcar_canfd_channel_probe(): register the CAN device when fully ready

Luiz Augusto von Dentz <[email protected]>
Bluetooth: hci_core: Fix leaking sent_cmd skb

Julian Braha <[email protected]>
ARM: 9178/1: fix unmet dependency on BITREVERSE for HAVE_ARCH_BITREVERSE

Alexander Lobakin <[email protected]>
MIPS: smp: fill in sibling and core maps earlier

Johannes Berg <[email protected]>
mac80211: refuse aggregations sessions before authorized

Corentin Labbe <[email protected]>
ARM: dts: rockchip: fix a typo on rk3288 crypto-controller

Sascha Hauer <[email protected]>
ARM: dts: rockchip: reorder rk322x hmdi clocks

Dinh Nguyen <[email protected]>
arm64: dts: agilex: use the compatible "intel,socfpga-agilex-hsotg"

Sascha Hauer <[email protected]>
arm64: dts: rockchip: reorder rk3399 hdmi clocks

Krzysztof Kozlowski <[email protected]>
arm64: dts: rockchip: align pl330 node name with dtschema

Jakob Unterwurzacher <[email protected]>
arm64: dts: rockchip: fix rk3399-puma eMMC HS400 signal integrity

Yan Yan <[email protected]>
xfrm: Fix xfrm migrate issues when address family changes

Yan Yan <[email protected]>
xfrm: Check if_id in xfrm_migrate

Quentin Schulz <[email protected]>
arm64: dts: rockchip: fix rk3399-puma-haikou USB OTG mode

Kai Lueke <[email protected]>
Revert "xfrm: state and policy should fail if XFRMA_IF_ID 0"

-------------

Diffstat:

 Makefile                                           |  4 ++--
 arch/arm/boot/dts/rk322x.dtsi                      |  4 ++--
 arch/arm/boot/dts/rk3288.dtsi                      |  2 +-
 arch/arm64/boot/dts/intel/socfpga_agilex.dtsi      |  4 ++--
 arch/arm64/boot/dts/rockchip/px30.dtsi             |  2 +-
 arch/arm64/boot/dts/rockchip/rk3328.dtsi           |  2 +-
 .../arm64/boot/dts/rockchip/rk3399-puma-haikou.dts |  1 +
 arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi      | 20 ++++++++++++++++
 arch/arm64/boot/dts/rockchip/rk3399.dtsi           |  6 ++---
 arch/mips/kernel/smp.c                             |  6 ++---
 arch/x86/kernel/module.c                           | 13 +++++++----
 drivers/atm/firestream.c                           |  2 ++
 drivers/gpu/drm/drm_connector.c                    |  3 +++
 drivers/net/can/rcar/rcar_canfd.c                  |  6 ++---
 drivers/net/ethernet/broadcom/bnx2.c               |  2 +-
 drivers/net/ethernet/intel/ice/ice.h               | 11 ++++++++-
 drivers/net/ethernet/intel/ice/ice_main.c          | 12 +++++++++-
 drivers/net/ethernet/sfc/mcdi.c                    |  2 +-
 drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c |  3 +--
 drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c  |  1 -
 include/net/xfrm.h                                 |  5 ++--
 lib/Kconfig                                        |  1 -
 net/bluetooth/hci_core.c                           |  1 +
 net/ipv4/tcp.c                                     | 10 ++++----
 net/key/af_key.c                                   |  2 +-
 net/mac80211/agg-tx.c                              | 10 +++++++-
 net/wireless/nl80211.c                             |  3 ++-
 net/xfrm/xfrm_policy.c                             | 14 ++++++-----
 net/xfrm/xfrm_state.c                              | 15 ++++++++----
 net/xfrm/xfrm_user.c                               | 27 +++++++---------------
 tools/testing/selftests/vm/userfaultfd.c           |  1 +
 31 files changed, 126 insertions(+), 69 deletions(-)

From: Kai Lueke <[email protected]>

commit a3d9001b4e287fc043e5539d03d71a32ab114bcb upstream.

This reverts commit 68ac0f3810e76a853b5f7b90601a05c3048b8b54 because ID 0 was meant to be used for configuring the policy/state without matching for a specific interface (e.g., Cilium is affected, see
https://github.com/cilium/cilium/pull/18789 and
https://github.com/cilium/cilium/pull/19019).

---
 net/xfrm/xfrm_user.c |   21 +++------------------
 1 file changed, 3 insertions(+), 18 deletions(-)

@@ -629,13 +629,8 @@ static struct xfrm_state *xfrm_state_con
 
 	xfrm_smark_init(attrs, &x->props.smark);
 
-	if (attrs[XFRMA_IF_ID]) {
+	if (attrs[XFRMA_IF_ID])
 		x->if_id = nla_get_u32(attrs[XFRMA_IF_ID]);
-		if (!x->if_id) {
-			err = -EINVAL;
-			goto error;
-		}
-	}
 
 	err = __xfrm_init_state(x, false, attrs[XFRMA_OFFLOAD_DEV]);
 	if (err)

@@ -1431,13 +1426,8 @@ static int xfrm_alloc_userspi(struct sk_
 
 	mark = xfrm_mark_get(attrs, &m);
 
-	if (attrs[XFRMA_IF_ID]) {
+	if (attrs[XFRMA_IF_ID])
 		if_id = nla_get_u32(attrs[XFRMA_IF_ID]);
-		if (!if_id) {
-			err = -EINVAL;
-			goto out_noput;
-		}
-	}
 
 	if (p->info.seq) {
 		x = xfrm_find_acq_byseq(net, mark, p->info.seq);

@@ -1750,13 +1740,8 @@ static struct xfrm_policy *xfrm_policy_c
 
 	xfrm_mark_get(attrs, &xp->mark);
 
-	if (attrs[XFRMA_IF_ID]) {
+	if (attrs[XFRMA_IF_ID])
 		xp->if_id = nla_get_u32(attrs[XFRMA_IF_ID]);
-		if (!xp->if_id) {
-			err = -EINVAL;
-			goto error;
-		}
-	}
 
 	return xp;
  error:

From: Quentin Schulz <[email protected]>

[ Upstream commit ed2c66a95c0c5669880aa93d0d34c6e9694b4cbd ]

The micro USB3.0 port available on the Haikou evaluation kit for Puma RK3399-Q7 SoM supports dual-role model (aka drd or OTG) but its support was broken until now because of missing logic around the ID pin.

This adds proper support for USB OTG on Puma Haikou by "connecting" the GPIO used for USB ID to the USB3 controller device.

---
 .../arm64/boot/dts/rockchip/rk3399-puma-haikou.dts |  1 +
 arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi      | 14 ++++++++++++++
 2 files changed, 15 insertions(+)

index 292bb7e80cf3..3ae5d727e367 100644
@@ -232,6 +232,7 @@
 
 &usbdrd_dwc3_0 {
 	dr_mode = "otg";
+	extcon = <&extcon_usb3>;
 	status = "okay";
 };
 

index fb67db4619ea..002ece51c3ba 100644
@@ -25,6 +25,13 @@
 		};
 	};
 
+	extcon_usb3: extcon-usb3 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb3_id>;
+	};
+
 	clkin_gmac: external-gmac-clock {
 		compatible = "fixed-clock";
 		clock-frequency = <125000000>;

@@ -422,6 +429,13 @@
 			  <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
+
+	usb3 {
+		usb3_id: usb3-id {
+			rockchip,pins =
+			  <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
 };
 
 &sdhci {

2.34.1

From: Yan Yan <[email protected]>

[ Upstream commit c1aca3080e382886e2e58e809787441984a2f89b ]

This patch enables distinguishing SAs and SPs based on if_id during the xfrm_migrate flow. This ensures support for xfrm interfaces throughout the SA/SP lifecycle.

When there are multiple existing SPs with the same direction, the same xfrm_selector and different endpoint addresses, xfrm_migrate might fail with ENODATA.

Specifically, the code path for performing xfrm_migrate is:
Stage 1: find policy to migrate with
xfrm_migrate_policy_find(sel, dir, type, net)
Stage 2: find and update state(s) with
xfrm_migrate_state_find(mp, net)
Stage 3: update endpoint address(es) of template(s) with
xfrm_policy_migrate(pol, m, num_migrate)

Currently "Stage 1" always returns the first xfrm_policy that matches, and "Stage 3" looks for the xfrm_tmpl that matches the old endpoint address. Thus if there are multiple xfrm_policy with same selector, direction, type and net, "Stage 1" might rertun a wrong xfrm_policy and "Stage 3" will fail with ENODATA because it cannot find a xfrm_tmpl with the matching endpoint address.

The fix is to allow userspace to pass an if_id and add if_id to the matching rule in Stage 1 and Stage 2 since if_id is a unique ID for xfrm_policy and xfrm_state. For compatibility, if_id will only be checked if the attribute is set.

Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/1668886

---
 include/net/xfrm.h     |  5 +++--
 net/key/af_key.c       |  2 +-
 net/xfrm/xfrm_policy.c | 14 ++++++++------
 net/xfrm/xfrm_state.c  |  7 ++++++-
 net/xfrm/xfrm_user.c   |  6 +++++-
 5 files changed, 23 insertions(+), 11 deletions(-)

index 301a164f17e9..358dfe6fefef 100644
@@ -1679,14 +1679,15 @@ int km_migrate(const struct xfrm_selector *sel, u8 dir, u8 type,
 	       const struct xfrm_migrate *m, int num_bundles,
 	       const struct xfrm_kmaddress *k,
 	       const struct xfrm_encap_tmpl *encap);
-struct xfrm_state *xfrm_migrate_state_find(struct xfrm_migrate *m, struct net *net);
+struct xfrm_state *xfrm_migrate_state_find(struct xfrm_migrate *m, struct net *net,
+						u32 if_id);
 struct xfrm_state *xfrm_state_migrate(struct xfrm_state *x,
 				      struct xfrm_migrate *m,
 				      struct xfrm_encap_tmpl *encap);
 int xfrm_migrate(const struct xfrm_selector *sel, u8 dir, u8 type,
 		 struct xfrm_migrate *m, int num_bundles,
 		 struct xfrm_kmaddress *k, struct net *net,
-		 struct xfrm_encap_tmpl *encap);
+		 struct xfrm_encap_tmpl *encap, u32 if_id);
 #endif
 
 int km_new_mapping(struct xfrm_state *x, xfrm_address_t *ipaddr, __be16 sport);

index de24a7d474df..9bf52a09b5ff 100644
@@ -2623,7 +2623,7 @@ static int pfkey_migrate(struct sock *sk, struct sk_buff *skb,
 	}
 
 	return xfrm_migrate(&sel, dir, XFRM_POLICY_TYPE_MAIN, m, i,
-			    kma ? &k : NULL, net, NULL);
+			    kma ? &k : NULL, net, NULL, 0);
 
  out:
 	return err;

index 37b149f63262..02099d113a0a 100644
@@ -4259,7 +4259,7 @@ static bool xfrm_migrate_selector_match(const struct xfrm_selector *sel_cmp,
 }
 
 static struct xfrm_policy *xfrm_migrate_policy_find(const struct xfrm_selector *sel,
-						    u8 dir, u8 type, struct net *net)
+						    u8 dir, u8 type, struct net *net, u32 if_id)
 {
 	struct xfrm_policy *pol, *ret = NULL;
 	struct hlist_head *chain;

@@ -4268,7 +4268,8 @@ static struct xfrm_policy *xfrm_migrate_policy_find(const struct xfrm_selector *
 	spin_lock_bh(&net->xfrm.xfrm_policy_lock);
 	chain = policy_hash_direct(net, &sel->daddr, &sel->saddr, sel->family, dir);
 	hlist_for_each_entry(pol, chain, bydst) {
-		if (xfrm_migrate_selector_match(sel, &pol->selector) &&
+		if ((if_id == 0 || pol->if_id == if_id) &&
+		    xfrm_migrate_selector_match(sel, &pol->selector) &&
 		    pol->type == type) {
 			ret = pol;
 			priority = ret->priority;

@@ -4280,7 +4281,8 @@ static struct xfrm_policy *xfrm_migrate_policy_find(const struct xfrm_selector *
 		if ((pol->priority >= priority) && ret)
 			break;
 
-		if (xfrm_migrate_selector_match(sel, &pol->selector) &&
+		if ((if_id == 0 || pol->if_id == if_id) &&
+		    xfrm_migrate_selector_match(sel, &pol->selector) &&
 		    pol->type == type) {
 			ret = pol;
 			break;

@@ -4396,7 +4398,7 @@ static int xfrm_migrate_check(const struct xfrm_migrate *m, int num_migrate)
 int xfrm_migrate(const struct xfrm_selector *sel, u8 dir, u8 type,
 		 struct xfrm_migrate *m, int num_migrate,
 		 struct xfrm_kmaddress *k, struct net *net,
-		 struct xfrm_encap_tmpl *encap)
+		 struct xfrm_encap_tmpl *encap, u32 if_id)
 {
 	int i, err, nx_cur = 0, nx_new = 0;
 	struct xfrm_policy *pol = NULL;

@@ -4415,14 +4417,14 @@ int xfrm_migrate(const struct xfrm_selector *sel, u8 dir, u8 type,
 	}
 
 	/* Stage 1 - find policy */
-	if ((pol = xfrm_migrate_policy_find(sel, dir, type, net)) == NULL) {
+	if ((pol = xfrm_migrate_policy_find(sel, dir, type, net, if_id)) == NULL) {
 		err = -ENOENT;
 		goto out;
 	}
 
 	/* Stage 2 - find and update state(s) */
 	for (i = 0, mp = m; i < num_migrate; i++, mp++) {
-		if ((x = xfrm_migrate_state_find(mp, net))) {
+		if ((x = xfrm_migrate_state_find(mp, net, if_id))) {
 			x_cur[nx_cur] = x;
 			nx_cur++;
 			xc = xfrm_state_migrate(x, mp, encap);

index 100b4b3723e7..291236d7676f 100644
@@ -1605,7 +1605,8 @@ static struct xfrm_state *xfrm_state_clone(struct xfrm_state *orig,
 	return NULL;
 }
 
-struct xfrm_state *xfrm_migrate_state_find(struct xfrm_migrate *m, struct net *net)
+struct xfrm_state *xfrm_migrate_state_find(struct xfrm_migrate *m, struct net *net,
+						u32 if_id)
 {
 	unsigned int h;
 	struct xfrm_state *x = NULL;

@@ -1621,6 +1622,8 @@ struct xfrm_state *xfrm_migrate_state_find(struct xfrm_migrate *m, struct net *n
 				continue;
 			if (m->reqid && x->props.reqid != m->reqid)
 				continue;
+			if (if_id != 0 && x->if_id != if_id)
+				continue;
 			if (!xfrm_addr_equal(&x->id.daddr, &m->old_daddr,
 					     m->old_family) ||
 			    !xfrm_addr_equal(&x->props.saddr, &m->old_saddr,

@@ -1636,6 +1639,8 @@ struct xfrm_state *xfrm_migrate_state_find(struct xfrm_migrate *m, struct net *n
 			if (x->props.mode != m->mode ||
 			    x->id.proto != m->proto)
 				continue;
+			if (if_id != 0 && x->if_id != if_id)
+				continue;
 			if (!xfrm_addr_equal(&x->id.daddr, &m->old_daddr,
 					     m->old_family) ||
 			    !xfrm_addr_equal(&x->props.saddr, &m->old_saddr,

index e13198f7e4e9..2acba159327c 100644
@@ -2592,6 +2592,7 @@ static int xfrm_do_migrate(struct sk_buff *skb, struct nlmsghdr *nlh,
 	int n = 0;
 	struct net *net = sock_net(skb->sk);
 	struct xfrm_encap_tmpl  *encap = NULL;
+	u32 if_id = 0;
 
 	if (attrs[XFRMA_MIGRATE] == NULL)
 		return -EINVAL;

@@ -2616,7 +2617,10 @@ static int xfrm_do_migrate(struct sk_buff *skb, struct nlmsghdr *nlh,
 			return -ENOMEM;
 	}
 
-	err = xfrm_migrate(&pi->sel, pi->dir, type, m, n, kmp, net, encap);
+	if (attrs[XFRMA_IF_ID])
+		if_id = nla_get_u32(attrs[XFRMA_IF_ID]);
+
+	err = xfrm_migrate(&pi->sel, pi->dir, type, m, n, kmp, net, encap, if_id);
 
 	kfree(encap);
 

2.34.1

From: Yan Yan <[email protected]>

[ Upstream commit e03c3bba351f99ad932e8f06baa9da1afc418e02 ]

xfrm_migrate cannot handle address family change of an xfrm_state. The symptons are the xfrm_state will be migrated to a wrong address, and sending as well as receiving packets wil be broken.

This commit fixes it by breaking the original xfrm_state_clone method into two steps so as to update the props.family before running xfrm_init_state. As the result, xfrm_state's inner mode, outer mode, type and IP header length in xfrm_state_migrate can be updated with the new address family.

Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/1885354

---
 net/xfrm/xfrm_state.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

index 291236d7676f..f7bfa1916968 100644
@@ -1578,9 +1578,6 @@ static struct xfrm_state *xfrm_state_clone(struct xfrm_state *orig,
 	memcpy(&x->mark, &orig->mark, sizeof(x->mark));
 	memcpy(&x->props.smark, &orig->props.smark, sizeof(x->props.smark));
 
-	if (xfrm_init_state(x) < 0)
-		goto error;
-
 	x->props.flags = orig->props.flags;
 	x->props.extra_flags = orig->props.extra_flags;
 

@@ -1667,6 +1664,11 @@ struct xfrm_state *xfrm_state_migrate(struct xfrm_state *x,
 	if (!xc)
 		return NULL;
 
+	xc->props.family = m->new_family;
+
+	if (xfrm_init_state(xc) < 0)
+		goto error;
+
 	memcpy(&xc->id.daddr, &m->new_daddr, sizeof(xc->id.daddr));
 	memcpy(&xc->props.saddr, &m->new_saddr, sizeof(xc->props.saddr));
 

2.34.1

From: Jakob Unterwurzacher <[email protected]>

[ Upstream commit 62966cbdda8a92f82d966a45aa671e788b2006f7 ]

There are signal integrity issues running the eMMC at 200MHz on Puma RK3399-Q7.

Similar to the work-around found for RK3399 Gru boards, lowering the frequency to 100MHz made the eMMC much more stable, so let's lower the frequency to 100MHz.

It might be possible to run at 150MHz as on RK3399 Gru boards but only 100MHz was extensively tested.

---
 arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

index 002ece51c3ba..08fa00364b42 100644
@@ -439,6 +439,12 @@
 };
 
 &sdhci {
+	/*
+	 * Signal integrity isn't great at 200MHz but 100MHz has proven stable
+	 * enough.
+	 */
+	max-frequency = <100000000>;
+
 	bus-width = <8>;
 	mmc-hs400-1_8v;
 	mmc-hs400-enhanced-strobe;

2.34.1

From: Krzysztof Kozlowski <[email protected]>

[ Upstream commit 8fd9415042826c7609c588e5ef45f3e84237785f ]

Fixes dtbs_check warnings like:

dmac@ff240000: $nodename:0: 'dmac@ff240000' does not match '^dma-controller(@.*)?$'

---
 arch/arm64/boot/dts/rockchip/px30.dtsi   | 2 +-
 arch/arm64/boot/dts/rockchip/rk3328.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

index 248ebb61aa79..5200d0bbd9e9 100644
@@ -711,7 +711,7 @@
 		clock-names = "pclk", "timer";
 	};
 
-	dmac: dmac@ff240000 {
+	dmac: dma-controller@ff240000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x0 0xff240000 0x0 0x4000>;
 		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,

index da84be6f4715..3cbe83e6fb9a 100644
@@ -489,7 +489,7 @@
 		status = "disabled";
 	};
 
-	dmac: dmac@ff1f0000 {
+	dmac: dma-controller@ff1f0000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x0 0xff1f0000 0x0 0x4000>;
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,

2.34.1

From: Sascha Hauer <[email protected]>

[ Upstream commit 2e8a8b5955a000cc655f7e368670518cbb77fe58 ]

The binding specifies the clock order to "cec", "grf", "vpll". Reorder the clocks accordingly.

---
 arch/arm64/boot/dts/rockchip/rk3399.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

index 3871c7fd83b0..00f1d036dfe0 100644
@@ -1802,10 +1802,10 @@
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH 0>;
 		clocks = <&cru PCLK_HDMI_CTRL>,
 			 <&cru SCLK_HDMI_SFR>,
-			 <&cru PLL_VPLL>,
+			 <&cru SCLK_HDMI_CEC>,
 			 <&cru PCLK_VIO_GRF>,
-			 <&cru SCLK_HDMI_CEC>;
-		clock-names = "iahb", "isfr", "vpll", "grf", "cec";
+			 <&cru PLL_VPLL>;
+		clock-names = "iahb", "isfr", "cec", "grf", "vpll";
 		power-domains = <&power RK3399_PD_HDCP>;
 		reg-io-width = <4>;
 		rockchip,grf = <&grf>;

2.34.1

From: Dinh Nguyen <[email protected]>

[ Upstream commit 268a491aebc25e6dc7c618903b09ac3a2e8af530 ]

The DWC2 USB controller on the Agilex platform does not support clock gating, so use the chip specific "intel,socfpga-agilex-hsotg" compatible.

---
 arch/arm64/boot/dts/intel/socfpga_agilex.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

index 163f33b46e4f..de1e98c99ec5 100644
@@ -502,7 +502,7 @@
 		};
 
 		usb0: usb@ffb00000 {
-			compatible = "snps,dwc2";
+			compatible = "intel,socfpga-agilex-hsotg", "snps,dwc2";
 			reg = <0xffb00000 0x40000>;
 			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
 			phys = <&usbphy0>;

@@ -515,7 +515,7 @@
 		};
 
 		usb1: usb@ffb40000 {
-			compatible = "snps,dwc2";
+			compatible = "intel,socfpga-agilex-hsotg", "snps,dwc2";
 			reg = <0xffb40000 0x40000>;
 			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
 			phys = <&usbphy0>;

2.34.1

From: Sascha Hauer <[email protected]>

[ Upstream commit be4e65bdffab5f588044325117df77dad7e9c45a ]

The binding specifies the clock order to "iahb", "isfr", "cec". Reorder the clocks accordingly.

---
 arch/arm/boot/dts/rk322x.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

index 75af99c76d7e..f31cf1df892b 100644
@@ -718,8 +718,8 @@
 		interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 		assigned-clocks = <&cru SCLK_HDMI_PHY>;
 		assigned-clock-parents = <&hdmi_phy>;
-		clocks = <&cru SCLK_HDMI_HDCP>, <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_CEC>;
-		clock-names = "isfr", "iahb", "cec";
+		clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>, <&cru SCLK_HDMI_CEC>;
+		clock-names = "iahb", "isfr", "cec";
 		pinctrl-names = "default";
 		pinctrl-0 = <&hdmii2c_xfer &hdmi_hpd &hdmi_cec>;
 		resets = <&cru SRST_HDMI_P>;

2.34.1

From: Corentin Labbe <[email protected]>

[ Upstream commit 3916c3619599a3970d3e6f98fb430b7c46266ada ]

crypto-controller had a typo, fix it.
In the same time, rename it to just crypto

---
 arch/arm/boot/dts/rk3288.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index 4dcdcf17c977..66ff5db53c5a 100644
@@ -971,7 +971,7 @@
 		status = "disabled";
 	};
 
-	crypto: cypto-controller@ff8a0000 {
+	crypto: crypto@ff8a0000 {
 		compatible = "rockchip,rk3288-crypto";
 		reg = <0x0 0xff8a0000 0x0 0x4000>;
 		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;

2.34.1

From: Johannes Berg <[email protected]>

[ Upstream commit a6bce78262f5dd4b50510f0aa47f3995f7b185f3 ]

If an MFP station isn't authorized, the receiver will (or at least should) drop the action frame since it's a robust management frame, but if we're not authorized we haven't installed keys yet. Refuse attempts to start a session as they'd just time out.

---
 net/mac80211/agg-tx.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

index 74a878f213d3..1deb3d874a4b 100644
@@ -9,7 +9,7 @@
  * Copyright 2007, Michael Wu <[email protected]>
  * Copyright 2007-2010, Intel Corporation
  * Copyright(c) 2015-2017 Intel Deutschland GmbH
- * Copyright (C) 2018 - 2021 Intel Corporation
+ * Copyright (C) 2018 - 2022 Intel Corporation
  */
 
 #include <linux/ieee80211.h>

@@ -626,6 +626,14 @@ int ieee80211_start_tx_ba_session(struct ieee80211_sta *pubsta, u16 tid,
 		return -EINVAL;
 	}
 
+	if (test_sta_flag(sta, WLAN_STA_MFP) &&
+	    !test_sta_flag(sta, WLAN_STA_AUTHORIZED)) {
+		ht_dbg(sdata,
+		       "MFP STA not authorized - deny BA session request %pM tid %d\n",
+		       sta->sta.addr, tid);
+		return -EINVAL;
+	}
+
 	/*
 	 * 802.11n-2009 11.5.1.1: If the initiating STA is an HT STA, is a
 	 * member of an IBSS, and has no other existing Block Ack agreement

2.34.1

From: Alexander Lobakin <[email protected]>

[ Upstream commit f2703def339c793674010cc9f01bfe4980231808 ]

After enabling CONFIG_SCHED_CORE (landed during 5.14 cycle), 2-core 2-thread-per-core interAptiv (CPS-driven) started emitting the following:

[    0.025698] CPU1 revision is: 0001a120 (MIPS interAptiv (multi))
[    0.048183] ------------[ cut here ]------------
[    0.048187] WARNING: CPU: 1 PID: 0 at kernel/sched/core.c:6025 sched_core_cpu_starting+0x198/0x240
[    0.048220] Modules linked in:
[    0.048233] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.17.0-rc3+ #35 b7b319f24073fd9a3c2aa7ad15fb7993eec0b26f
[    0.048247] Stack : 817f0000 00000004 327804c8 810eb050 00000000 00000004 00000000 c314fdd1
[    0.048278]         830cbd64 819c0000 81800000 817f0000 83070bf4 00000001 830cbd08 00000000
[    0.048307]         00000000 00000000 815fcbc4 00000000 00000000 00000000 00000000 00000000
[    0.048334]         00000000 00000000 00000000 00000000 817f0000 00000000 00000000 817f6f34
[    0.048361]         817f0000 818a3c00 817f0000 00000004 00000000 00000000 4dc33260 0018c933
[    0.048389]         ...
[    0.048396] Call Trace:
[    0.048399] [<8105a7bc>] show_stack+0x3c/0x140
[    0.048424] [<8131c2a0>] dump_stack_lvl+0x60/0x80
[    0.048440] [<8108b5c0>] __warn+0xc0/0xf4
[    0.048454] [<8108b658>] warn_slowpath_fmt+0x64/0x10c
[    0.048467] [<810bd418>] sched_core_cpu_starting+0x198/0x240
[    0.048483] [<810c6514>] sched_cpu_starting+0x14/0x80
[    0.048497] [<8108c0f8>] cpuhp_invoke_callback_range+0x78/0x140
[    0.048510] [<8108d914>] notify_cpu_starting+0x94/0x140
[    0.048523] [<8106593c>] start_secondary+0xbc/0x280
[    0.048539]
[    0.048543] ---[ end trace 0000000000000000 ]---
[    0.048636] Synchronize counters for CPU 1: done.

...for each but CPU 0/boot.
Basic debug printks right before the mentioned line say:

[    0.048170] CPU: 1, smt_mask:

So smt_mask, which is sibling mask obviously, is empty when entering the function.
This is critical, as sched_core_cpu_starting() calculates core-scheduling parameters only once per CPU start, and it's crucial to have all the parameters filled in at that moment (at least it uses cpu_smt_mask() which in fact is &cpu_sibling_map[cpu] on MIPS).

A bit of debugging led me to that set_cpu_sibling_map() performing the actual map calculation, was being invocated after notify_cpu_start(), and exactly the latter function starts CPU HP callback round (sched_core_cpu_starting() is basically a CPU HP callback).
While the flow is same on ARM64 (maps after the notifier, although before calling set_cpu_online()), x86 started calculating sibling maps earlier than starting the CPU HP callbacks in Linux 4.14 (see
[0] for the reference). Neither me nor my brief tests couldn't find any potential caveats in calculating the maps right after performing delay calibration, but the WARN splat is now gone.
The very same debug prints now yield exactly what I expected from them:

[    0.048433] CPU: 1, smt_mask: 0-1

[0] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=76ce7cfe35ef

---
 arch/mips/kernel/smp.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

index d542fb7af3ba..1986d1309410 100644
@@ -351,6 +351,9 @@ asmlinkage void start_secondary(void)
 	cpu = smp_processor_id();
 	cpu_data[cpu].udelay_val = loops_per_jiffy;
 
+	set_cpu_sibling_map(cpu);
+	set_cpu_core_map(cpu);
+
 	cpumask_set_cpu(cpu, &cpu_coherent_mask);
 	notify_cpu_starting(cpu);
 

@@ -362,9 +365,6 @@ asmlinkage void start_secondary(void)
 	/* The CPU is running and counters synchronised, now mark it online */
 	set_cpu_online(cpu, true);
 
-	set_cpu_sibling_map(cpu);
-	set_cpu_core_map(cpu);
-
 	calculate_cpu_foreign_map();
 
 	/*

2.34.1

From: Julian Braha <[email protected]>

[ Upstream commit 11c57c3ba94da74c3446924260e34e0b1950b5d7 ]

Resending this to properly add it to the patch tracker - thanks for letting me know, Arnd :)

When ARM is enabled, and BITREVERSE is disabled,
Kbuild gives the following warning:

WARNING: unmet direct dependencies detected for HAVE_ARCH_BITREVERSE
Depends on [n]: BITREVERSE [=n]
Selected by [y]:
- ARM [=y] && (CPU_32v7M [=n] || CPU_32v7 [=y]) && !CPU_32v6 [=n]

This is because ARM selects HAVE_ARCH_BITREVERSE
without selecting BITREVERSE, despite
HAVE_ARCH_BITREVERSE depending on BITREVERSE.

This unmet dependency bug was found by Kismet,
a static analysis tool for Kconfig. Please advise if this is not the appropriate solution.

---
 lib/Kconfig | 1 -
 1 file changed, 1 deletion(-)

index 5e7165e6a346..fa4b10322efc 100644
@@ -45,7 +45,6 @@ config BITREVERSE
 config HAVE_ARCH_BITREVERSE
 	bool
 	default n
-	depends on BITREVERSE
 	help
 	  This option enables the use of hardware bit-reversal instructions on
 	  architectures which support such operations.

2.34.1

From: Luiz Augusto von Dentz <[email protected]>

[ Upstream commit dd3b1dc3dd050f1f47cd13e300732852414270f8 ]

sent_cmd memory is not freed before freeing hci_dev causing it to leak it contents.

---
 net/bluetooth/hci_core.c | 1 +
 1 file changed, 1 insertion(+)

index 53f1b08017aa..c67390367cc2 100644
@@ -4083,6 +4083,7 @@ void hci_release_dev(struct hci_dev *hdev)
 	hci_dev_unlock(hdev);
 
 	ida_simple_remove(&hci_index_ida, hdev->id);
+	kfree_skb(hdev->sent_cmd);
 	kfree(hdev);
 }
 EXPORT_SYMBOL(hci_release_dev);

2.34.1

From: Lad Prabhakar <[email protected]>

[ Upstream commit c5048a7b2c23ab589f3476a783bd586b663eda5b ]

Register the CAN device only when all the necessary initialization is completed. This patch makes sure all the data structures and locks are initialized before registering the CAN device.

---
 drivers/net/can/rcar/rcar_canfd.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

index 388521e70837..2f44c567ebd7 100644
@@ -1720,15 +1720,15 @@ static int rcar_canfd_channel_probe(struct rcar_canfd_global *gpriv, u32 ch,
 
 	netif_napi_add(ndev, &priv->napi, rcar_canfd_rx_poll,
 		       RCANFD_NAPI_WEIGHT);
+	spin_lock_init(&priv->tx_lock);
+	devm_can_led_init(ndev);
+	gpriv->ch[priv->channel] = priv;
 	err = register_candev(ndev);
 	if (err) {
 		dev_err(&pdev->dev,
 			"register_candev() failed, error %d\n", err);
 		goto fail_candev;
 	}
-	spin_lock_init(&priv->tx_lock);
-	devm_can_led_init(ndev);
-	gpriv->ch[priv->channel] = priv;
 	dev_info(&pdev->dev, "device registered (channel %u)\n", priv->channel);
 	return 0;
 

2.34.1

From: Jia-Ju Bai <[email protected]>

[ Upstream commit d4e26aaea7f82ba884dcb4acfe689406bc092dc3 ]

The function ioremap() in fs_init() can fail, so its return value should be checked.

---
 drivers/atm/firestream.c | 2 ++
 1 file changed, 2 insertions(+)

index 3bc3c314a467..4f67404fe64c 100644
@@ -1676,6 +1676,8 @@ static int fs_init(struct fs_dev *dev)
 	dev->hw_base = pci_resource_start(pci_dev, 0);
 
 	dev->base = ioremap(dev->hw_base, 0x1000);
+	if (!dev->base)
+		return 1;
 
 	reset_chip (dev);
   

2.34.1

From: Golan Ben Ami <[email protected]>

[ Upstream commit 1db5fcbba2631277b78d7f8aff99c9607d29f6d8 ]

Some APs misbehave when TWT is used and cause our firmware to crash. We don't know a reasonable way to detect and work around this problem in the FW yet. To prevent these crashes, disable TWT in the driver by stopping to advertise TWT support.

---
 drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c | 3 +--
 drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c  | 1 -
 2 files changed, 1 insertion(+), 3 deletions(-)

index 475f951d4b1e..fc40cca096c2 100644
@@ -541,8 +541,7 @@ static const struct ieee80211_sband_iftype_data iwl_he_capa[] = {
 			.has_he = true,
 			.he_cap_elem = {
 				.mac_cap_info[0] =
-					IEEE80211_HE_MAC_CAP0_HTC_HE |
-					IEEE80211_HE_MAC_CAP0_TWT_REQ,
+					IEEE80211_HE_MAC_CAP0_HTC_HE,
 				.mac_cap_info[1] =
 					IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_16US |
 					IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_8,

index 750217393f48..56c7a68a6491 100644
@@ -295,7 +295,6 @@ static const u8 he_if_types_ext_capa_sta[] = {
 	 [0] = WLAN_EXT_CAPA1_EXT_CHANNEL_SWITCHING,
 	 [2] = WLAN_EXT_CAPA3_MULTI_BSSID_SUPPORT,
 	 [7] = WLAN_EXT_CAPA8_OPMODE_NOTIF,
-	 [9] = WLAN_EXT_CAPA10_TWT_REQUESTER_SUPPORT,
 };
 
 static const struct wiphy_iftype_ext_capab he_iftypes_ext_capa[] = {

2.34.1

From: Manasi Navare <[email protected]>

[ Upstream commit 62929726ef0ec72cbbe9440c5d125d4278b99894 ]

VRR capable property is not attached by default to the connector It is attached only if VRR is supported.
So if the driver tries to call drm core set prop function without it being attached that causes NULL dereference.

---
 drivers/gpu/drm/drm_connector.c | 3 +++
 1 file changed, 3 insertions(+)

index 2ba257b1ae20..e9b7926d9b66 100644
@@ -2233,6 +2233,9 @@ EXPORT_SYMBOL(drm_connector_atomic_hdr_metadata_equal);
 void drm_connector_set_vrr_capable_property(
 		struct drm_connector *connector, bool capable)
 {
+	if (!connector->vrr_capable_property)
+		return;
+
 	drm_object_property_set_value(&connector->base,
 				      connector->vrr_capable_property,
 				      capable);

2.34.1

From: Sreeramya Soratkal <[email protected]>

[ Upstream commit e50b88c4f076242358b66ddb67482b96947438f2 ]

The wdev channel information is updated post channel switch only for the station mode and not for the other modes. Due to this, the P2P client still points to the old value though it moved to the new channel when the channel change is induced from the P2P GO.

Update the bss channel after CSA channel switch completion for P2P client interface as well.

---
 net/wireless/nl80211.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

index 99564db14aa1..2f9ead98a9da 100644
@@ -17525,7 +17525,8 @@ void cfg80211_ch_switch_notify(struct net_device *dev,
 	wdev->chandef = *chandef;
 	wdev->preset_chandef = *chandef;
 
-	if (wdev->iftype == NL80211_IFTYPE_STATION &&
+	if ((wdev->iftype == NL80211_IFTYPE_STATION ||
+	     wdev->iftype == NL80211_IFTYPE_P2P_CLIENT) &&
 	    !WARN_ON(!wdev->current_bss))
 		cfg80211_update_assoc_bss_entry(wdev, chandef->chan);
 

2.34.1

From: Eric Dumazet <[email protected]>

[ Upstream commit e3d5ea2c011ecb16fb94c56a659364e6b30fac94 ]

If recv_actor() returns an incorrect value, tcp_read_sock() might loop forever.

Instead, issue a one time warning and make sure to make progress.

---
 net/ipv4/tcp.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

index f48f1059b31a..ef68d55e0944 100644
@@ -1663,11 +1663,13 @@ int tcp_read_sock(struct sock *sk, read_descriptor_t *desc,
 				if (!copied)
 					copied = used;
 				break;
-			} else if (used <= len) {
-				seq += used;
-				copied += used;
-				offset += used;
 			}
+			if (WARN_ON_ONCE(used > len))
+				used = len;
+			seq += used;
+			copied += used;
+			offset += used;
+
 			/* If recv_actor drops the lock (e.g. TCP splice
 			 * receive) the skb pointer might be invalid when
 			 * getting here: tcp_collapse might have deleted it

2.34.1

From: Niels Dossche <[email protected]>

[ Upstream commit f1fb205efb0ccca55626fd4ef38570dd16b44719 ]

seqno could be read as a stale value outside of the lock. The lock is already acquired to protect the modification of seqno against a possible race condition. Place the reading of this value also inside this locking to protect it against a possible race condition.

---
 drivers/net/ethernet/sfc/mcdi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index be6bfd6b7ec7..50baf62b2cbc 100644
@@ -163,9 +163,9 @@ static void efx_mcdi_send_request(struct efx_nic *efx, unsigned cmd,
 	/* Serialise with efx_mcdi_ev_cpl() and efx_mcdi_ev_death() */
 	spin_lock_bh(&mcdi->iface_lock);
 	++mcdi->seqno;
+	seqno = mcdi->seqno & SEQ_MASK;
 	spin_unlock_bh(&mcdi->iface_lock);
 
-	seqno = mcdi->seqno & SEQ_MASK;
 	xflags = 0;
 	if (mcdi->mode == MCDI_MODE_EVENTS)
 		xflags |= MCDI_HEADER_XFLAGS_EVREQ;

2.34.1

From: Christophe JAILLET <[email protected]>

[ Upstream commit 8ccffe9ac3239e549beaa0a9d5e1a1eac94e866c ]

Fix an error message and report the correct failing function.

---
 drivers/net/ethernet/broadcom/bnx2.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index 8c83973adca5..9d70d908c064 100644
@@ -8212,7 +8212,7 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev)
 		rc = dma_set_coherent_mask(&pdev->dev, persist_dma_mask);
 		if (rc) {
 			dev_err(&pdev->dev,
-				"pci_set_consistent_dma_mask failed, aborting\n");
+				"dma_set_coherent_mask failed, aborting\n");
 			goto err_out_unmap;
 		}
 	} else if ((rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32))) != 0) {

2.34.1

From: Chengming Zhou <[email protected]>

[ Upstream commit b773827e361952b3f53ac6fa4c4e39ccd632102e ]

The error message when I build vm tests on debian10 (GLIBC 2.28):

userfaultfd.c: In function `userfaultfd_pagemap_test':
userfaultfd.c:1393:37: error: MADV_PAGEOUT' undeclared (first use in this function); did you mean MADV_RANDOM'?
if (madvise(area_dst, test_pgsize, MADV_PAGEOUT))
^~~~~~~~~~~~ MADV_RANDOM

This patch includes these newer definitions from UAPI linux/mman.h, is useful to fix tests build on systems without these definitions in glibc sys/mman.h.

---
 tools/testing/selftests/vm/userfaultfd.c |    1 +
 1 file changed, 1 insertion(+)

@@ -46,6 +46,7 @@
 #include <signal.h>
 #include <poll.h>
 #include <string.h>
+#include <linux/mman.h>
 #include <sys/mman.h>
 #include <sys/syscall.h>
 #include <sys/ioctl.h>

From: Peter Zijlstra <[email protected]>

commit 5adf349439d29f92467e864f728dfc23180f3ef9 upstream.

Ever since commit

4e6292114c74 ("x86/paravirt: Add new features for paravirt patching")

there is an ordering dependency between patching paravirt ops and patching alternatives, the module loader still violates this.

---
 arch/x86/kernel/module.c |   13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)

@@ -270,6 +270,14 @@ int module_finalize(const Elf_Ehdr *hdr,
 			orc_ip = s;
 	}
 
+	/*
+	 * See alternative_instructions() for the ordering rules between the
+	 * various patching types.
+	 */
+	if (para) {
+		void *pseg = (void *)para->sh_addr;
+		apply_paravirt(pseg, pseg + para->sh_size);
+	}
 	if (alt) {
 		/* patch .altinstructions */
 		void *aseg = (void *)alt->sh_addr;

@@ -283,11 +291,6 @@ int module_finalize(const Elf_Ehdr *hdr,
 					    tseg, tseg + text->sh_size);
 	}
 
-	if (para) {
-		void *pseg = (void *)para->sh_addr;
-		apply_paravirt(pseg, pseg + para->sh_size);
-	}
-
 	/* make jump label nops */
 	jump_label_apply_nops(me);
 

From: Ivan Vecera <[email protected]>

commit 5cb1ebdbc4342b1c2ce89516e19808d64417bdbc upstream.

Commit 5dbbbd01cbba83 ("ice: Avoid RTNL lock when re-creating auxiliary device") changes a process of re-creation of aux device so ice_plug_aux_dev() is called from ice_service_task() context. This unfortunately opens a race window that can result in dead-lock when interface has left LAG and immediately enters LAG again.

Reproducer:

```
#!/bin/sh

ip link add lag0 type bond mode 1 miimon 100
ip link set lag0

for n in {1..10}; do
        echo Cycle: $n
        ip link set ens7f0 master lag0
        sleep 1
        ip link set ens7f0 nomaster
done
```

This results in:

[20976.208697] Workqueue: ice ice_service_task [ice]
[20976.213422] Call Trace:
[20976.215871]  __schedule+0x2d1/0x830
[20976.219364]  schedule+0x35/0xa0
[20976.222510]  schedule_preempt_disabled+0xa/0x10
[20976.227043]  __mutex_lock.isra.7+0x310/0x420
[20976.235071]  enum_all_gids_of_dev_cb+0x1c/0x100 [ib_core]
[20976.251215]  ib_enum_roce_netdev+0xa4/0xe0 [ib_core]
[20976.256192]  ib_cache_setup_one+0x33/0xa0 [ib_core]
[20976.261079]  ib_register_device+0x40d/0x580 [ib_core]
[20976.266139]  irdma_ib_register_device+0x129/0x250 [irdma]
[20976.281409]  irdma_probe+0x2c1/0x360 [irdma]
[20976.285691]  auxiliary_bus_probe+0x45/0x70
[20976.289790]  really_probe+0x1f2/0x480
[20976.298509]  driver_probe_device+0x49/0xc0
[20976.302609]  bus_for_each_drv+0x79/0xc0
[20976.306448]  __device_attach+0xdc/0x160
[20976.310286]  bus_probe_device+0x9d/0xb0
[20976.314128]  device_add+0x43c/0x890
[20976.321287]  __auxiliary_device_add+0x43/0x60
[20976.325644]  ice_plug_aux_dev+0xb2/0x100 [ice]
[20976.330109]  ice_service_task+0xd0c/0xed0 [ice]
[20976.342591]  process_one_work+0x1a7/0x360
[20976.350536]  worker_thread+0x30/0x390
[20976.358128]  kthread+0x10a/0x120
[20976.365547]  ret_from_fork+0x1f/0x40
...
[20976.438030] task:ip              state:D stack:    0 pid:213658 ppid:213627 flags:0x00004084
[20976.446469] Call Trace:
[20976.448921]  __schedule+0x2d1/0x830
[20976.452414]  schedule+0x35/0xa0
[20976.455559]  schedule_preempt_disabled+0xa/0x10
[20976.460090]  __mutex_lock.isra.7+0x310/0x420
[20976.464364]  device_del+0x36/0x3c0
[20976.467772]  ice_unplug_aux_dev+0x1a/0x40 [ice]
[20976.472313]  ice_lag_event_handler+0x2a2/0x520 [ice]
[20976.477288]  notifier_call_chain+0x47/0x70
[20976.481386]  __netdev_upper_dev_link+0x18b/0x280
[20976.489845]  bond_enslave+0xe05/0x1790 [bonding]
[20976.494475]  do_setlink+0x336/0xf50
[20976.502517]  __rtnl_newlink+0x529/0x8b0
[20976.543441]  rtnl_newlink+0x43/0x60
[20976.546934]  rtnetlink_rcv_msg+0x2b1/0x360
[20976.559238]  netlink_rcv_skb+0x4c/0x120
[20976.563079]  netlink_unicast+0x196/0x230
[20976.567005]  netlink_sendmsg+0x204/0x3d0
[20976.570930]  sock_sendmsg+0x4c/0x50
[20976.574423]  ____sys_sendmsg+0x1eb/0x250
[20976.586807]  ___sys_sendmsg+0x7c/0xc0
[20976.606353]  __sys_sendmsg+0x57/0xa0
[20976.609930]  do_syscall_64+0x5b/0x1a0
[20976.613598]  entry_SYSCALL_64_after_hwframe+0x65/0xca

1. Command 'ip link ... set nomaster' causes that ice_plug_aux_dev() is called from ice_service_task() context, aux device is created and associated device->lock is taken.
2. Command 'ip link ... set master...' calls ice's notifier under RTNL lock and that notifier calls ice_unplug_aux_dev(). That function tries to take aux device->lock but this is already taken by ice_plug_aux_dev() in step 1
3. Later ice_plug_aux_dev() tries to take RTNL lock but this is already taken in step 2
4. Dead-lock

The patch fixes this issue by following changes:
- Bit ICE_FLAG_PLUG_AUX_DEV is kept to be set during ice_plug_aux_dev() call in ice_service_task()
- The bit is checked in ice_clear_rdma_cap() and only if it is not set then ice_unplug_aux_dev() is called. If it is set (in other words plugging of aux device was requested and ice_plug_aux_dev() is potentially running) then the function only clears the bit
- Once ice_plug_aux_dev() call (in ice_service_task) is finished the bit ICE_FLAG_PLUG_AUX_DEV is cleared but it is also checked whether it was already cleared by ice_clear_rdma_cap(). If so then aux device is unplugged.

---
 drivers/net/ethernet/intel/ice/ice.h      |   11 ++++++++++-
 drivers/net/ethernet/intel/ice/ice_main.c |   12 +++++++++++-
 2 files changed, 21 insertions(+), 2 deletions(-)

@@ -703,7 +703,16 @@ static inline void ice_set_rdma_cap(stru
  */
 static inline void ice_clear_rdma_cap(struct ice_pf *pf)
 {
-	ice_unplug_aux_dev(pf);
+	/* We can directly unplug aux device here only if the flag bit
+	 * ICE_FLAG_PLUG_AUX_DEV is not set because ice_unplug_aux_dev()
+	 * could race with ice_plug_aux_dev() called from
+	 * ice_service_task(). In this case we only clear that bit now and
+	 * aux device will be unplugged later once ice_plug_aux_device()
+	 * called from ice_service_task() finishes (see ice_service_task()).
+	 */
+	if (!test_and_clear_bit(ICE_FLAG_PLUG_AUX_DEV, pf->flags))
+		ice_unplug_aux_dev(pf);
+
 	clear_bit(ICE_FLAG_RDMA_ENA, pf->flags);
 	clear_bit(ICE_FLAG_AUX_ENA, pf->flags);
 }

@@ -2143,9 +2143,19 @@ static void ice_service_task(struct work
 		return;
 	}
 
-	if (test_and_clear_bit(ICE_FLAG_PLUG_AUX_DEV, pf->flags))
+	if (test_bit(ICE_FLAG_PLUG_AUX_DEV, pf->flags)) {
+		/* Plug aux device per request */
 		ice_plug_aux_dev(pf);
 
+		/* Mark plugging as done but check whether unplug was
+		 * requested during ice_plug_aux_dev() call
+		 * (e.g. from ice_clear_rdma_cap()) and if so then
+		 * plug aux device.
+		 */
+		if (!test_and_clear_bit(ICE_FLAG_PLUG_AUX_DEV, pf->flags))
+			ice_unplug_aux_dev(pf);
+	}
+
 	if (test_and_clear_bit(ICE_FLAG_MTU_CHANGED, pf->flags)) {
 		struct iidc_event *event;
 

On ARCH_BRCMSTB using 32-bit and 64-bit ARM kernels:

Florian

Built and booted successfully on RISC-V RV64 (HiFive Unmatched).

5.15.30-rc1 Successfully Compiled and booted on my Raspberry PI 4b (8g) (bcm2711)

Build results:

	total: 156 pass: 156 fail: 0
Qemu test results:
	total: 488 pass: 488 fail: 0

Guenter

Results from Linaro’s test farm.
No regressions on arm64, arm, x86_64, and i386.

## Build
* kernel: 5.15.30-rc1
* git: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
* git branch: linux-5.15.y
* git commit: 1d4b468d2e8dfe717ff4f4991fa8f8decad564a5
* git describe: v5.15.29-26-g1d4b468d2e8d
* test details:
https://qa-reports.linaro.org/lkft/linux-stable-rc-linux-5.15.y/build/v5.15.29-26-g1d4b468d2e8d

## Test Regressions (compared to v5.15.29)
No test regressions found.

## Metric Regressions (compared to v5.15.29)
No metric regressions found.

## Test Fixes (compared to v5.15.29)
No test fixes found.

## Metric Fixes (compared to v5.15.29)
No metric fixes found.

## Test result summary
total: 106421, pass: 90242, fail: 1005, skip: 14074, xfail: 1100

## Build Summary
* arc: 10 total, 10 passed, 0 failed
* arm: 296 total, 293 passed, 3 failed
* arm64: 47 total, 47 passed, 0 failed
* dragonboard-410c: 1 total, 1 passed, 0 failed
* hi6220-hikey: 1 total, 1 passed, 0 failed
* i386: 45 total, 41 passed, 4 failed
* juno-r2: 1 total, 1 passed, 0 failed
* mips: 41 total, 38 passed, 3 failed
* parisc: 14 total, 14 passed, 0 failed
* powerpc: 65 total, 50 passed, 15 failed
* riscv: 32 total, 27 passed, 5 failed
* s390: 26 total, 23 passed, 3 failed
* sh: 26 total, 24 passed, 2 failed
* sparc: 14 total, 14 passed, 0 failed
* x15: 1 total, 1 passed, 0 failed
* x86: 1 total, 1 passed, 0 failed
* x86_64: 47 total, 47 passed, 0 failed

## Test suites summary
* fwts
* igt-gpu-tools
* kselftest-
* kselftest-android
* kselftest-arm64
* kselftest-bpf
* kselftest-breakpoints
* kselftest-capabilities
* kselftest-cgroup
* kselftest-clone3
* kselftest-core
* kselftest-cpu-hotplug
* kselftest-cpufreq
* kselftest-drivers
* kselftest-efivarfs
* kselftest-filesystems
* kselftest-firmware
* kselftest-fpu
* kselftest-futex
* kselftest-gpio
* kselftest-intel_pstate
* kselftest-ipc
* kselftest-ir
* kselftest-kcmp
* kselftest-kexec
* kselftest-kvm
* kselftest-lib
* kselftest-livepatch
* kselftest-membarrier
* kselftest-memfd
* kselftest-memory-hotplug
* kselftest-mincore
* kselftest-mount
* kselftest-mqueue
* kselftest-net
* kselftest-netfilter
* kselftest-nsfs
* kselftest-openat2
* kselftest-pid_namespace
* kselftest-pidfd
* kselftest-proc
* kselftest-pstore
* kselftest-ptrace
* kselftest-rseq
* kselftest-rtc
* kselftest-seccomp
* kselftest-sigaltstack
* kselftest-size
* kselftest-splice
* kselftest-static_keys
* kselftest-sync
* kselftest-sysctl
* kselftest-tc-testing
* kselftest-timens
* kselftest-timers
* kselftest-tmpfs
* kselftest-tpm2
* kselftest-user
* kselftest-vm
* kselftest-x86
* kselftest-zram
* kunit
* kvm-unit-tests
* libgpiod
* libhugetlbfs
* linux-log-parser
* ltp-cap_bounds-tests
* ltp-commands-tests
* ltp-containers-tests
* ltp-controllers-tests
* ltp-cpuhotplug-tests
* ltp-crypto-tests
* ltp-cve-tests
* ltp-dio-tests
* ltp-fcntl-locktests-tests
* ltp-filecaps-tests
* ltp-fs-tests
* ltp-fs_bind-tests
* ltp-fs_bind[
* ltp-fs_perms_simple-tests
* ltp-fsx-tests
* ltp-hugetlb-tests
* ltp-io-tests
* ltp-ipc-tests
* ltp-math-tests
* ltp-mm-tests
* ltp-nptl-tests
* ltp-open-posix-tests
* ltp-pty-tests
* ltp-sched-tests
* ltp-securebits-tests
* ltp-syscalls-tests
* ltp-tracing-tests
* network-basic-tests
* packetdrill
* perf
* perf/Zstd-perf.data-compression
* rcutorture
* ssuite
* v4l2-compliance
* vdso

--
Linaro LKFT
https://lkft.linaro.org

Successfully cross-compiled for arm64 (bcm2711_defconfig, gcc 10.2.0) and powerpc (ps3_defconfig, gcc 11.2.0).

An old man doll... just what I always wanted! - Clara

All tests passing for Tegra ...

Test results for stable-v5.15:

    10 builds:	10 pass, 0 fail
    28 boots:	28 pass, 0 fail
    114 tests:	114 pass, 0 fail

Linux version: 5.15.30-rc1-g1d4b468d2e8d
Boards tested: tegra124-jetson-tk1, tegra186-p2771-0000,

                tegra194-p2972-0000, tegra194-p3509-0000+p3668-0000,
                tegra20-ventana, tegra210-p2371-2180,
                tegra210-p3450-0000, tegra30-cardhu-a04

Jon

Hi Greg,

Build test:
mips (gcc version 11.2.1 20220301): 62 configs -> no new failure arm (gcc version 11.2.1 20220301): 100 configs -> no new failure arm64 (gcc version 11.2.1 20220301): 3 configs -> no failure x86_64 (gcc version 11.2.1 20220301): 4 configs -> no failure

Boot test:
x86_64: Booted on my test laptop. No regression.
x86_64: Booted on qemu. No regression. [1]
arm64: Booted on rpi4b (4GB model). No regression. [2]
mips: Booted on ci20 board. No regression. [3]

[1]. https://openqa.qa.codethink.co.uk/tests/904
[2]. https://openqa.qa.codethink.co.uk/tests/909
[3]. https://openqa.qa.codethink.co.uk/tests/910

--
Regards
Sudip