IMXRT: Maintnice updates
Subsystems (6)
v2 cover IMXRT: Maintnice updates
Updates to the imxrt family include:
- Adding missing include in board
- Moving pinctrl binding to dts
- Reducing SYS_MALLOC_LEN
- Using device tree for anatop base address
Jesse Taube (4):
clk: imxrt: Use dts for anatop base address configs/*imxrt10*: SYS_MALLOC_LEN is too large
ARM: dts: imxrt10..-evk: Linux moved pins-imxrt1020 to dts
board: freescale: imxrt10..-evk: Fix missing include of serial.h
arch/arm/dts/imxrt1020-evk-u-boot.dtsi | 4 ++++ arch/arm/dts/imxrt1020-evk.dts | 2 +- .../pins-imxrt1020.h => arch/arm/dts/imxrt1020-pinfunc.h | 0 arch/arm/dts/imxrt1020.dtsi | 5 +++++ arch/arm/dts/imxrt1050-evk-u-boot.dtsi | 4 ++++ arch/arm/dts/imxrt1050-evk.dts | 2 +- .../pins-imxrt1050.h => arch/arm/dts/imxrt1050-pinfunc.h | 0 arch/arm/dts/imxrt1050.dtsi | 5 +++++ arch/arm/include/asm/arch-imxrt/imx-regs.h | 2 -- board/freescale/imxrt1020-evk/imxrt1020-evk.c | 1 + board/freescale/imxrt1050-evk/imxrt1050-evk.c | 1 + configs/imxrt1020-evk_defconfig | 2 +- configs/imxrt1050-evk_defconfig | 2 +- drivers/clk/imx/clk-imxrt1020.c | 2 +- drivers/clk/imx/clk-imxrt1050.c | 2 +- 15 files changed, 26 insertions(+), 8 deletions(-) rename include/dt-bindings/pinctrl/pins-imxrt1020.h => arch/arm/dts/imxrt1020-pinfunc.h (100%) rename include/dt-bindings/pinctrl/pins-imxrt1050.h => arch/arm/dts/imxrt1050-pinfunc.h (100%)
Signature · 1 line
2.34.1
PATCH v2 1/4 clk: imxrt: Use dts for anatop base address
In Linux IMX and IMXRT use the device tree to hold the anatop address. The anatop is used in clock drivers as it controls the internal PLLs This will move the macro from asm/arch-imxrt to the device tree. This presumably should also be done with the other IMX boards as well.
--- arch/arm/dts/imxrt1020-evk-u-boot.dtsi | 4 ++++ arch/arm/dts/imxrt1020.dtsi | 5 +++++ arch/arm/dts/imxrt1050-evk-u-boot.dtsi | 4 ++++ arch/arm/dts/imxrt1050.dtsi | 5 +++++ arch/arm/include/asm/arch-imxrt/imx-regs.h | 2 -- drivers/clk/imx/clk-imxrt1020.c | 2 +- drivers/clk/imx/clk-imxrt1050.c | 2 +- 7 files changed, 20 insertions(+), 4 deletions(-)
arch/arm/dts/imxrt1020-evk-u-boot.dtsi +4 -0
@@ -22,6 +22,10 @@ u-boot,dm-spl; }; +&anatop { + u-boot,dm-spl; +}; + &clks { u-boot,dm-spl; };
arch/arm/dts/imxrt1020.dtsi +5 -0
@@ -67,6 +67,11 @@ fsl,mux_mask = <0x7>; }; + anatop: anatop@400d8000 { + compatible = "fsl,imxrt-anatop"; + reg = <0x400d8000 0x4000>; + }; + clks: ccm@400fc000 { compatible = "fsl,imxrt1020-ccm"; reg = <0x400fc000 0x4000>;
arch/arm/dts/imxrt1050-evk-u-boot.dtsi +4 -0
@@ -22,6 +22,10 @@ u-boot,dm-spl; }; +&anatop { + u-boot,dm-spl; +}; + &clks { u-boot,dm-spl; };
arch/arm/dts/imxrt1050.dtsi +5 -0
@@ -59,6 +59,11 @@ fsl,mux_mask = <0x7>; }; + anatop: anatop@400d8000 { + compatible = "fsl,imxrt-anatop"; + reg = <0x400d8000 0x4000>; + }; + clks: ccm@400fc000 { compatible = "fsl,imxrt1050-ccm"; reg = <0x400fc000 0x4000>;
arch/arm/include/asm/arch-imxrt/imx-regs.h +0 -2
@@ -15,8 +15,6 @@#define GPIO4_BASE_ADDR 0x401C4000#define GPIO5_BASE_ADDR 0x400C0000 -#define ANATOP_BASE_ADDR 0x400d8000 -#define MXS_LCDIF_BASE 0x402b8000#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))
drivers/clk/imx/clk-imxrt1020.c +1 -1
@@ -93,7 +93,7 @@ static int imxrt1020_clk_probe(struct udevice *dev)void *base;/* Anatop clocks */ - base = (void *)ANATOP_BASE_ADDR ; + base = (void *)ofnode_get_addr (ofnode_by_compatible (ofnode_null (),"fsl,imxrt-anatop" )); clk_dm(IMXRT1020_CLK_PLL2_SYS, imx_clk_pllv3(IMX_PLLV3_GENERIC, "pll2_sys", "osc",
drivers/clk/imx/clk-imxrt1050.c +1 -1
@@ -117,7 +117,7 @@ static int imxrt1050_clk_probe(struct udevice *dev)void *base;/* Anatop clocks */ - base = (void *)ANATOP_BASE_ADDR ; + base = (void *)ofnode_get_addr (ofnode_by_compatible (ofnode_null (),"fsl,imxrt-anatop" )); clk_dm(IMXRT1050_CLK_PLL1_REF_SEL, imx_clk_mux("pll1_arm_ref_sel", base + 0x0, 14, 2,
Signature · 1 line
2.34.1
PATCH v2 1/4 clk: imxrt: Use dts for anatop base address
Quoted 5 lines
In Linux IMX and IMXRT use the device tree to hold the anatop address. The anatop is used in clock drivers as it controls the internal PLLs This will move the macro from asm/arch-imxrt to the device tree. This presumably should also be done with the other IMX boards as well.
Signed-off-by Jesse Taube <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v2 2/4 configs/*imxrt10*: SYS_MALLOC_LEN is too large
In reply to Jesse Taube1M of heap is more than internal ram making booting without SDRAM not possible now it is 256k
--- configs/imxrt1020-evk_defconfig | 2 +- configs/imxrt1050-evk_defconfig | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
configs/imxrt1020-evk_defconfig +1 -1
@@ -1,7 +1,7 @@ CONFIG_ARM=y CONFIG_ARCH_IMXRT=y CONFIG_SYS_TEXT_BASE=0x80002000 -CONFIG_SYS_MALLOC_LEN=0x100000 +CONFIG_SYS_MALLOC_LEN=0x40000 CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y
configs/imxrt1050-evk_defconfig +1 -1
@@ -3,7 +3,7 @@ CONFIG_SYS_DCACHE_OFF=y # CONFIG_SPL_SYS_DCACHE_OFF is not set CONFIG_ARCH_IMXRT=y CONFIG_SYS_TEXT_BASE=0x80002000 -CONFIG_SYS_MALLOC_LEN=0x100000 +CONFIG_SYS_MALLOC_LEN=0x40000 CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y
Signature · 1 line
2.34.1
PATCH v2 2/4 configs/*imxrt10*: SYS_MALLOC_LEN is too large
Quoted 3 lines
1M of heap is more than internal ram making booting without SDRAM not possible now it is 256k
Signed-off-by Jesse Taube <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v2 3/4 ARM: dts: imxrt10..-evk: Linux moved pins-imxrt1020 to dts
In reply to Jesse TaubeThe Linux kernel moved dt-bindings/pinctrl/pins-imxrt to the device tree This patch move it in U-Boot as well.
--- arch/arm/dts/imxrt1020-evk.dts | 2 +- .../pins-imxrt1020.h => arch/arm/dts/imxrt1020-pinfunc.h | 0 arch/arm/dts/imxrt1050-evk.dts | 2 +- .../pins-imxrt1050.h => arch/arm/dts/imxrt1050-pinfunc.h | 0 4 files changed, 2 insertions(+), 2 deletions(-) rename include/dt-bindings/pinctrl/pins-imxrt1020.h => arch/arm/dts/imxrt1020-pinfunc.h (100%) rename include/dt-bindings/pinctrl/pins-imxrt1050.h => arch/arm/dts/imxrt1050-pinfunc.h (100%)
arch/arm/dts/imxrt1020-evk.dts +1 -1
@@ -7,7 +7,7 @@ /dts-v1/; #include "imxrt1020.dtsi" #include "imxrt1020-evk-u-boot.dtsi" -#include <dt-bindings/pinctrl/pins-imxrt1020.h> +#include "imxrt1020-pinfunc.h" / { model = "NXP IMXRT1020-evk board";
arch/arm/dts/imxrt1020-pinfunc.h renamed from include/dt-bindings/pinctrl/pins-imxrt1020.h +0 -0
arch/arm/dts/imxrt1050-evk.dts +1 -1
@@ -7,7 +7,7 @@ /dts-v1/; #include "imxrt1050.dtsi" #include "imxrt1050-evk-u-boot.dtsi" -#include <dt-bindings/pinctrl/pins-imxrt1050.h> +#include "imxrt1050-pinfunc.h" / { model = "NXP IMXRT1050-evk board";
arch/arm/dts/imxrt1050-pinfunc.h renamed from include/dt-bindings/pinctrl/pins-imxrt1050.h +0 -0
Signature · 1 line
2.34.1
PATCH v2 3/4 ARM: dts: imxrt10..-evk: Linux moved pins-imxrt1020 to dts
Quoted 3 lines
The Linux kernel moved dt-bindings/pinctrl/pins-imxrt to the device tree This patch move it in U-Boot as well.
Signed-off-by Jesse Taube <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v2 4/4 board: freescale: imxrt10..-evk: Fix missing include of serial.h
In reply to Jesse TaubeIf FALCON mode is enabled we have a missing include in spl_start_uboot.
--- board/freescale/imxrt1020-evk/imxrt1020-evk.c | 1 + board/freescale/imxrt1050-evk/imxrt1050-evk.c | 1 + 2 files changed, 2 insertions(+)
board/freescale/imxrt1020-evk/imxrt1020-evk.c +1 -0
@@ -13,6 +13,7 @@#include <asm/global_data.h> #include <asm/io.h> #include <asm/armv7m.h> +#include <serial.h> DECLARE_GLOBAL_DATA_PTR ;
board/freescale/imxrt1050-evk/imxrt1050-evk.c +1 -0
@@ -13,6 +13,7 @@#include <asm/global_data.h> #include <asm/io.h> #include <asm/armv7m.h> +#include <serial.h> DECLARE_GLOBAL_DATA_PTR ;
Signature · 1 line
2.34.1
PATCH v2 4/4 board: freescale: imxrt10..-evk: Fix missing include of serial.h
Quoted 2 lines
If FALCON mode is enabled we have a missing include in
spl_start_uboot.Signed-off-by Jesse Taube <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Quoted 11 lines · Jesse Taube
Updates to the imxrt family include:
- Adding missing include in board
- Moving pinctrl binding to dts
- ReducingSYS_MALLOC_LEN
- Using device tree for anatop base addressJesse Taube (4):
clk: imxrt: Use dts for anatop base address configs/*imxrt10*:SYS_MALLOC_LENis too large
ARM: dts: imxrt10..-evk: Linux moved pins-imxrt1020 to dts
board: freescale: imxrt10..-evk: Fix missing include ofserial.h
Quoted 20 lines
arch/arm/dts/imxrt1020-evk-u-boot.dtsi | 4 ++++ arch/arm/dts/imxrt1020-evk.dts | 2 +- .../pins-imxrt1020.h => arch/arm/dts/imxrt1020-pinfunc.h | 0 arch/arm/dts/imxrt1020.dtsi | 5 +++++ arch/arm/dts/imxrt1050-evk-u-boot.dtsi | 4 ++++ arch/arm/dts/imxrt1050-evk.dts | 2 +- .../pins-imxrt1050.h => arch/arm/dts/imxrt1050-pinfunc.h | 0 arch/arm/dts/imxrt1050.dtsi | 5 +++++ arch/arm/include/asm/arch-imxrt/imx-regs.h | 2 -- board/freescale/imxrt1020-evk/imxrt1020-evk.c | 1 + board/freescale/imxrt1050-evk/imxrt1050-evk.c | 1 + configs/imxrt1020-evk_defconfig | 2 +- configs/imxrt1050-evk_defconfig | 2 +- drivers/clk/imx/clk-imxrt1020.c | 2 +- drivers/clk/imx/clk-imxrt1050.c | 2 +- 15 files changed, 26 insertions(+), 8 deletions(-)rename
include/dt-bindings/pinctrl/pins-imxrt1020.h=>arch/arm/dts/imxrt1020-pinfunc.h(100%) renameinclude/dt-bindings/pinctrl/pins-imxrt1050.h=>arch/arm/dts/imxrt1050-pinfunc.h(100%)