Skip to contentSkip to conversation

ice: Fix broken IFF_ALLMULTI handling

PATCH Superseded Ivan Vecera 3 participants 5 messages Mar 21, 2022 – Mar 25, 2022

Subsystems (3)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ice: Fix broken IFF_ALLMULTI handling

Handling of all-multicast flag and associated multicast promiscuous mode is broken in ice driver. When a user switches allmulticast flag on or off the driver checks whether any VLANs are configured over the interface (except default VLAN 0).

If any extra VLANs are registered it enables multicast promiscuous mode for all these VLANs (including default VLAN 0) using ICE_SW_LKUP_PROMISC_VLAN look-up type. In this situation all multicast packets tagged with known VLAN ID or untagged are received and multicast packets tagged with unknown VLAN ID ignored.

If no extra VLANs are registered (so only VLAN 0 exists) it enables multicast promiscuous mode for VLAN 0 and uses ICE_SW_LKUP_PROMISC look-up type. In this situation any multicast packets including tagged ones are received.

The driver handles IFF_ALLMULTI in ice_vsi_sync_fltr() this way:

ice_vsi_sync_fltr() {
...

  if (changed_flags & IFF_ALLMULTI) {
    if (netdev->flags & IFF_ALLMULTI) {
      if (vsi->num_vlans > 1)
        ice_set_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
      else
        ice_set_promisc(..., ICE_MCAST_PROMISC_BITS);
    } else {
      if (vsi->num_vlans > 1)
        ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
      else
        ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS);
    }

}
...
}

The code above depends on value vsi->num_vlan that specifies number of VLANs configured over the interface (including VLAN 0) and this is problem because that value is modified in NDO callbacks ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid().

Scenario 1:
1. ip link set ens7f0 allmulticast on
2. ip link add vlan10 link ens7f0 type vlan id 10
3. ip link set ens7f0 allmulticast off
4. ip link set ens7f0 allmulticast on

[1] In this scenario IFF_ALLMULTI is enabled and the driver calls ice_set_promisc(..., ICE_MCAST_PROMISC_BITS) that installs multicast promisc rule with non-VLAN look-up type.
[2] Then VLAN with ID 10 is added and vsi->num_vlan incremented to 2
[3] Command switches IFF_ALLMULTI off and the driver calls ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS) but this call is effectively NOP because it looks for multicast promisc rules for VLAN 0 and VLAN 10 with VLAN look-up type but no such rules exist. So the all-multicast remains enabled silently in hardware.
[4] Command tries to switch IFF_ALLMULTI on and the driver calls ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS) but this call fails (-EEXIST) because non-VLAN multicast promisc rule already exists.

Scenario 2:
1. ip link add vlan10 link ens7f0 type vlan id 10
2. ip link set ens7f0 allmulticast on
3. ip link add vlan20 link ens7f0 type vlan id 20
4. ip link del vlan10 ; ip link del vlan20
5. ip link set ens7f0 allmulticast off

[1] VLAN with ID 10 is added and vsi->num_vlan==2
[2] Command switches IFF_ALLMULTI on and driver installs multicast promisc rules with VLAN look-up type for VLAN 0 and 10
[3] VLAN with ID 20 is added and vsi->num_vlan==3 but no multicast promisc rules is added for this new VLAN so the interface does not receive MC packets from VLAN 20
[4] Both VLANs are removed but multicast rule for VLAN 10 remains installed so interface receives multicast packets from VLAN 10
[5] Command switches IFF_ALLMULTI off and because vsi->num_vlan is 1 the driver tries to remove multicast promisc rule for VLAN 0 with non-VLAN look-up that does not exist. All-multicast looks disabled from user point of view but it is partially enabled in HW (interface receives all multicast packets either untagged or tagged with VLAN ID 10)

To resolve these issues the patch introduces these changes:
1. Adds handling for IFF_ALLMULTI to ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid() callbacks. So when VLAN is added/removed and IFF_ALLMULTI is enabled an appropriate multicast promisc rule for that VLAN ID is added/removed.
2. In ice_vlan_rx_add_vid() when first VLAN besides VLAN 0 is added so (vsi->num_vlan == 2) and IFF_ALLMULTI is enabled then look-up type for existing multicast promisc rule for VLAN 0 is updated to ICE_MCAST_VLAN_PROMISC_BITS.
3. In ice_vlan_rx_kill_vid() when last VLAN besides VLAN 0 is removed so (vsi->num_vlan == 1) and IFF_ALLMULTI is enabled then look-up type for existing multicast promisc rule for VLAN 0 is updated to ICE_MCAST_PROMISC_BITS.
4. Both ice_vlan_rx_{add,kill}_vid() have to run under ICE_CFG_BUSY bit protection to avoid races with ice_vsi_sync_fltr() that runs in ice_service_task() context.
5. Bit ICE_VSI_VLAN_FLTR_CHANGED is use-less and can be removed.
6. Error messages added to ice_fltr_*_vsi_promisc() helper functions to avoid them in their callers
7. Small improvements to increase readability

Fixes 5eda8afd6bcc ("ice: Add support for PF/VF promiscuous mode")
---
 drivers/net/ethernet/intel/ice/ice.h      |   1 -
 drivers/net/ethernet/intel/ice/ice_fltr.c |  52 +++++++++-
 drivers/net/ethernet/intel/ice/ice_main.c | 119 +++++++++++++++-------
 3 files changed, 131 insertions(+), 41 deletions(-)
drivers/net/ethernet/intel/ice/ice.h +0 -1
index bea1d1e39fa2..717542e49d65 100644
@@ -300,7 +300,6 @@ enum ice_vsi_state {
 	ICE_VSI_NETDEV_REGISTERED,
 	ICE_VSI_UMAC_FLTR_CHANGED,
 	ICE_VSI_MMAC_FLTR_CHANGED,
-	ICE_VSI_VLAN_FLTR_CHANGED,
 	ICE_VSI_PROMISC_CHANGED,
 	ICE_VSI_STATE_NBITS		/* must be last */
 };
drivers/net/ethernet/intel/ice/ice_fltr.c +48 -4

76 lines not on this page · raw message

drivers/net/ethernet/intel/ice/ice_main.c +83 -36

191 lines not on this page · raw message

Signature · 1 line
2.34.1
#1 lore raw

PATCH 1/1 ice: Fix broken IFF_ALLMULTI handling

Quoted 135 lines · Ivan Vecera

Handling of all-multicast flag and associated multicast promiscuous mode is broken in ice driver. When a user switches allmulticast flag on or off the driver checks whether any VLANs are configured over the interface (except default VLAN 0).

If any extra VLANs are registered it enables multicast promiscuous mode for all these VLANs (including default VLAN 0) using ICE_SW_LKUP_PROMISC_VLAN look-up type. In this situation all multicast packets tagged with known VLAN ID or untagged are received and multicast packets tagged with unknown VLAN ID ignored.

If no extra VLANs are registered (so only VLAN 0 exists) it enables multicast promiscuous mode for VLAN 0 and uses ICE_SW_LKUP_PROMISC look-up type. In this situation any multicast packets including tagged ones are received.

The driver handles IFF_ALLMULTI in ice_vsi_sync_fltr() this way:

ice_vsi_sync_fltr() {
...

  if (changed_flags & IFF_ALLMULTI) {
    if (netdev->flags & IFF_ALLMULTI) {
      if (vsi->num_vlans > 1)
        ice_set_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
      else
        ice_set_promisc(..., ICE_MCAST_PROMISC_BITS);
    } else {
      if (vsi->num_vlans > 1)
        ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
      else
        ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS);
    }

}
...
}

The code above depends on value vsi->num_vlan that specifies number of VLANs configured over the interface (including VLAN 0) and this is problem because that value is modified in NDO callbacks ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid().

Scenario 1:
1. ip link set ens7f0 allmulticast on
2. ip link add vlan10 link ens7f0 type vlan id 10
3. ip link set ens7f0 allmulticast off
4. ip link set ens7f0 allmulticast on

[1] In this scenario IFF_ALLMULTI is enabled and the driver calls ice_set_promisc(..., ICE_MCAST_PROMISC_BITS) that installs multicast promisc rule with non-VLAN look-up type.
[2] Then VLAN with ID 10 is added and vsi->num_vlan incremented to 2
[3] Command switches IFF_ALLMULTI off and the driver calls ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS) but this call is effectively NOP because it looks for multicast promisc rules for VLAN 0 and VLAN 10 with VLAN look-up type but no such rules exist. So the all-multicast remains enabled silently in hardware.
[4] Command tries to switch IFF_ALLMULTI on and the driver calls ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS) but this call fails (-EEXIST) because non-VLAN multicast promisc rule already exists.

Scenario 2:
1. ip link add vlan10 link ens7f0 type vlan id 10
2. ip link set ens7f0 allmulticast on
3. ip link add vlan20 link ens7f0 type vlan id 20
4. ip link del vlan10 ; ip link del vlan20
5. ip link set ens7f0 allmulticast off

[1] VLAN with ID 10 is added and vsi->num_vlan==2
[2] Command switches IFF_ALLMULTI on and driver installs multicast promisc rules with VLAN look-up type for VLAN 0 and 10
[3] VLAN with ID 20 is added and vsi->num_vlan==3 but no multicast promisc rules is added for this new VLAN so the interface does not receive MC packets from VLAN 20
[4] Both VLANs are removed but multicast rule for VLAN 10 remains installed so interface receives multicast packets from VLAN 10
[5] Command switches IFF_ALLMULTI off and because vsi->num_vlan is 1 the driver tries to remove multicast promisc rule for VLAN 0 with non-VLAN look-up that does not exist. All-multicast looks disabled from user point of view but it is partially enabled in HW (interface receives all multicast packets either untagged or tagged with VLAN ID 10)

To resolve these issues the patch introduces these changes:
1. Adds handling for IFF_ALLMULTI to ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid() callbacks. So when VLAN is added/removed and IFF_ALLMULTI is enabled an appropriate multicast promisc rule for that VLAN ID is added/removed.
2. In ice_vlan_rx_add_vid() when first VLAN besides VLAN 0 is added so (vsi->num_vlan == 2) and IFF_ALLMULTI is enabled then look-up type for existing multicast promisc rule for VLAN 0 is updated to ICE_MCAST_VLAN_PROMISC_BITS.
3. In ice_vlan_rx_kill_vid() when last VLAN besides VLAN 0 is removed so (vsi->num_vlan == 1) and IFF_ALLMULTI is enabled then look-up type for existing multicast promisc rule for VLAN 0 is updated to ICE_MCAST_PROMISC_BITS.
4. Both ice_vlan_rx_{add,kill}_vid() have to run under ICE_CFG_BUSY bit protection to avoid races with ice_vsi_sync_fltr() that runs in ice_service_task() context.
5. Bit ICE_VSI_VLAN_FLTR_CHANGED is use-less and can be removed.
6. Error messages added to ice_fltr_*_vsi_promisc() helper functions to avoid them in their callers
7. Small improvements to increase readability

Fixes 5eda8afd6bcc ("ice: Add support for PF/VF promiscuous mode")
---
 drivers/net/ethernet/intel/ice/ice.h      |   1 -
 drivers/net/ethernet/intel/ice/ice_fltr.c |  52 +++++++++-
 drivers/net/ethernet/intel/ice/ice_main.c | 119 +++++++++++++++-------
 3 files changed, 131 insertions(+), 41 deletions(-)
drivers/net/ethernet/intel/ice/ice.h +0 -1
index bea1d1e39fa2..717542e49d65 100644
@@ -300,7 +300,6 @@ enum ice_vsi_state {
 	ICE_VSI_NETDEV_REGISTERED,
 	ICE_VSI_UMAC_FLTR_CHANGED,
 	ICE_VSI_MMAC_FLTR_CHANGED,
-	ICE_VSI_VLAN_FLTR_CHANGED,
 	ICE_VSI_PROMISC_CHANGED,
 	ICE_VSI_STATE_NBITS		/* must be last */
 };
drivers/net/ethernet/intel/ice/ice_fltr.c +1 -1
index c29177c6bb9d..8ed87b43a367 100644
@@ -58,7 +58,18 @@ int
 ice_fltr_set_vlan_vsi_promisc(struct ice_hw *hw, struct ice_vsi *vsi,
 			      u8 promisc_mask)
 {
-	return ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, false);
+	struct ice_pf *pf = hw->back;

drivers/net/ethernet/intel/ice/ice_fltr.c int · line 71

Quoted 10 lines
drivers/net/ethernet/intel/ice/ice_fltr.c +10 -0
+	int result;
+
+	result = ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, false);
+	if (!result)
+		return result;
+
+	dev_err(ice_pf_to_dev(pf),
+		"Error setting promisc mode on VSI %i (rc=%d)\n", vsi->vsi_num,
+		result);
+

Our typical style here would be to do:

result = <function>;

if (result) {
	dev_err(...);
}

I find that much more readable than "if (!result) return;

Quoted 69 lines
drivers/net/ethernet/intel/ice/ice_fltr.c +37 -3
+	return result;
 }
 
 /**
@@ -73,7 +84,18 @@ int
 ice_fltr_clear_vlan_vsi_promisc(struct ice_hw *hw, struct ice_vsi *vsi,
 				u8 promisc_mask)
 {
-	return ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, true);
+	struct ice_pf *pf = hw->back;
+	int result;
+
+	result = ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, true);
+	if (!result)
+		return result;
+
+	dev_err(ice_pf_to_dev(pf),
+		"Error clearing promisc mode on VSI %i (rc=%d)\n",
+		vsi->vsi_num, result);
+
+	return result;
 }
 
 /**
@@ -87,7 +109,18 @@ int
 ice_fltr_clear_vsi_promisc(struct ice_hw *hw, u16 vsi_handle, u8 promisc_mask,
 			   u16 vid)
 {
-	return ice_clear_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
+	struct ice_pf *pf = hw->back;
+	int result;
+
+	result = ice_clear_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
+	if (!result)
+		return result;
+
+	dev_err(ice_pf_to_dev(pf),
+		"Error clearing promisc mode on VSI %i for VID %u (rc=%d)\n",
+		ice_get_hw_vsi_num(hw, vsi_handle), vid, result);
+
+	return result;
 }
 
 /**
@@ -101,7 +134,18 @@ int
 ice_fltr_set_vsi_promisc(struct ice_hw *hw, u16 vsi_handle, u8 promisc_mask,
 			 u16 vid)
 {
-	return ice_set_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
+	struct ice_pf *pf = hw->back;
+	int result;
+
+	result = ice_set_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
+	if (!result)
+		return result;
+
+	dev_err(ice_pf_to_dev(pf),
+		"Error setting promisc mode on VSI %i for VID %u (rc=%d)\n",
+		ice_get_hw_vsi_num(hw, vsi_handle), vid, result);
+
+	return result;
 }
 
 /**
drivers/net/ethernet/intel/ice/ice_main.c +0 -0
index b7e8744b0c0a..168a41ea37b8 100644

drivers/net/ethernet/intel/ice/ice_main.c static int ice_add_mac_to_unsync_list(struct net_device *netdev, const u8 *addr) · line 230

Quoted 6 lines
drivers/net/ethernet/intel/ice/ice_main.c +1 -2
@@ -227,8 +227,7 @@ static int ice_add_mac_to_unsync_list(struct net_device *netdev, const u8 *addr)
 static bool ice_vsi_fltr_changed(struct ice_vsi *vsi)
 {
 	return test_bit(ICE_VSI_UMAC_FLTR_CHANGED, vsi->state) ||
-	       test_bit(ICE_VSI_MMAC_FLTR_CHANGED, vsi->state) ||
-	       test_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
+	       test_bit(ICE_VSI_MMAC_FLTR_CHANGED, vsi->state);

Ok, so we now handle VLAN filters seprately without these states.

Quoted 5 lines
drivers/net/ethernet/intel/ice/ice_main.c +0 -0
 }
 
 /**
@@ -244,10 +243,15 @@ static int ice_set_promisc(struct ice_vsi *vsi, u8 promisc_m)
 	if (vsi->type != ICE_VSI_PF)

drivers/net/ethernet/intel/ice/ice_main.c static int ice_set_promisc(struct ice_vsi *vsi, u8 promisc_m) · line 249

Quoted 10 lines
drivers/net/ethernet/intel/ice/ice_main.c +4 -4
 		return 0;
 
-	if (vsi->num_vlan > 1)
-		status = ice_fltr_set_vlan_vsi_promisc(&vsi->back->hw, vsi, promisc_m);
-	else
-		status = ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx, promisc_m, 0);
+	if (vsi->num_vlan > 1) {
+		promisc_m |= (ICE_PROMISC_VLAN_RX | ICE_PROMISC_VLAN_TX);
+		status = ice_fltr_set_vlan_vsi_promisc(&vsi->back->hw, vsi,
+						       promisc_m);

Ok so if we're in >1 filter, we add the VLAN_RX and VLAN_TX flags. Right.

And we know that changes only from another ndo op to add VLANs?

Quoted 77 lines
drivers/net/ethernet/intel/ice/ice_main.c +16 -22
+	} else {
+		status = ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
+						  promisc_m, 0);
+	}
+
 	return status;
 }
 
@@ -264,10 +268,15 @@ static int ice_clear_promisc(struct ice_vsi *vsi, u8 promisc_m)
 	if (vsi->type != ICE_VSI_PF)
 		return 0;
 
-	if (vsi->num_vlan > 1)
-		status = ice_fltr_clear_vlan_vsi_promisc(&vsi->back->hw, vsi, promisc_m);
-	else
-		status = ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx, promisc_m, 0);
+	if (vsi->num_vlan > 1) {
+		promisc_m |= (ICE_PROMISC_VLAN_RX | ICE_PROMISC_VLAN_TX);
+		status = ice_fltr_clear_vlan_vsi_promisc(&vsi->back->hw, vsi,
+							 promisc_m);
+	} else {
+		status = ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
+						    promisc_m, 0);
+	}
+
 	return status;
 }
 
@@ -285,7 +294,6 @@ static int ice_vsi_sync_fltr(struct ice_vsi *vsi)
 	struct ice_pf *pf = vsi->back;
 	struct ice_hw *hw = &pf->hw;
 	u32 changed_flags = 0;
-	u8 promisc_m;
 	int err;
 
 	if (!vsi->netdev)
@@ -303,7 +311,6 @@ static int ice_vsi_sync_fltr(struct ice_vsi *vsi)
 	if (ice_vsi_fltr_changed(vsi)) {
 		clear_bit(ICE_VSI_UMAC_FLTR_CHANGED, vsi->state);
 		clear_bit(ICE_VSI_MMAC_FLTR_CHANGED, vsi->state);
-		clear_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
 
 		/* grab the netdev's addr_list_lock */
 		netif_addr_lock_bh(netdev);
@@ -352,29 +359,15 @@ static int ice_vsi_sync_fltr(struct ice_vsi *vsi)
 	/* check for changes in promiscuous modes */
 	if (changed_flags & IFF_ALLMULTI) {
 		if (vsi->current_netdev_flags & IFF_ALLMULTI) {
-			if (vsi->num_vlan > 1)
-				promisc_m = ICE_MCAST_VLAN_PROMISC_BITS;
-			else
-				promisc_m = ICE_MCAST_PROMISC_BITS;
-
-			err = ice_set_promisc(vsi, promisc_m);
+			err = ice_set_promisc(vsi, ICE_MCAST_PROMISC_BITS);
 			if (err) {
-				netdev_err(netdev, "Error setting Multicast promiscuous mode on VSI %i\n",
-					   vsi->vsi_num);
 				vsi->current_netdev_flags &= ~IFF_ALLMULTI;
 				goto out_promisc;
 			}
 		} else {
 			/* !(vsi->current_netdev_flags & IFF_ALLMULTI) */
-			if (vsi->num_vlan > 1)
-				promisc_m = ICE_MCAST_VLAN_PROMISC_BITS;
-			else
-				promisc_m = ICE_MCAST_PROMISC_BITS;
-
-			err = ice_clear_promisc(vsi, promisc_m);
+			err = ice_clear_promisc(vsi, ICE_MCAST_PROMISC_BITS);
 			if (err) {
-				netdev_err(netdev, "Error clearing Multicast promiscuous mode on VSI %i\n",
-					   vsi->vsi_num);
 				vsi->current_netdev_flags |= IFF_ALLMULTI;
 				goto out_promisc;
 			}

drivers/net/ethernet/intel/ice/ice_main.c ice_vlan_rx_add_vid(struct net_device *netdev, __always_unused __be16 proto, · line 3443

Quoted 6 lines
drivers/net/ethernet/intel/ice/ice_main.c +3 -0
@@ -3445,19 +3438,47 @@ ice_vlan_rx_add_vid(struct net_device *netdev, __always_unused __be16 proto,
 	if (!vid)
 		return 0;
 
+	while (test_and_set_bit(ICE_CFG_BUSY, vsi->state))
+		usleep_range(1000, 2000);
+

Not your fault, but every time I see this I think about why not just making this a mutex...

Quoted 8 lines
drivers/net/ethernet/intel/ice/ice_main.c +3 -1
 	/* Enable VLAN pruning when a VLAN other than 0 is added */
 	if (!ice_vsi_is_vlan_pruning_ena(vsi)) {
 		ret = ice_cfg_vlan_pruning(vsi, true);
 		if (ret)
-			return ret;
+			goto finish;
+	}
+

drivers/net/ethernet/intel/ice/ice_main.c ice_vlan_rx_add_vid(struct net_device *netdev, __always_unused __be16 proto, · line 3460

Quoted 10 lines
drivers/net/ethernet/intel/ice/ice_main.c +9 -0
+	/* Add multicast promisc rule for the VLAN ID to be added if
+	 * all-multicast is currently enabled.
+	 */
+	if (vsi->current_netdev_flags & IFF_ALLMULTI) {
+		ret = ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
+					       ICE_MCAST_VLAN_PROMISC_BITS,
+					       vid);
+		if (ret)
+			goto finish;
 	}

If we're not in multicast mode (or if multicast mode gets disabled) when do we clear these bits?

I would have expected some sort of loop to iterate over VLANs?

Quoted 76 lines
drivers/net/ethernet/intel/ice/ice_main.c +47 -7
 	/* Add a switch rule for this VLAN ID so its corresponding VLAN tagged
 	 * packets aren't pruned by the device's internal switch on Rx
 	 */
 	ret = ice_vsi_add_vlan(vsi, vid, ICE_FWD_TO_VSI);
-	if (!ret)
-		set_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
+	if (ret)
+		goto finish;
+
+	/* If all-multicast is currently enabled and this VLAN ID is only one
+	 * besides VLAN-0 we have to update look-up type of multicast promisc
+	 * rule for VLAN-0 from ICE_SW_LKUP_PROMISC to ICE_SW_LKUP_PROMISC_VLAN.
+	 */
+	if ((vsi->current_netdev_flags & IFF_ALLMULTI) && vsi->num_vlan == 2) {
+		ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
+					   ICE_MCAST_PROMISC_BITS, 0);
+		ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
+					 ICE_MCAST_VLAN_PROMISC_BITS, 0);
+	}
+
+finish:
+	clear_bit(ICE_CFG_BUSY, vsi->state);
 
 	return ret;
 }
@@ -3482,18 +3503,44 @@ ice_vlan_rx_kill_vid(struct net_device *netdev, __always_unused __be16 proto,
 	if (!vid)
 		return 0;
 
+	while (test_and_set_bit(ICE_CFG_BUSY, vsi->state))
+		usleep_range(1000, 2000);
+
 	/* Make sure ice_vsi_kill_vlan is successful before updating VLAN
 	 * information
 	 */
 	ret = ice_vsi_kill_vlan(vsi, vid);
 	if (ret)
-		return ret;
+		goto finish;
 
-	/* Disable pruning when VLAN 0 is the only VLAN rule */
-	if (vsi->num_vlan == 1 && ice_vsi_is_vlan_pruning_ena(vsi))
-		ret = ice_cfg_vlan_pruning(vsi, false);
+	/* Remove multicast promisc rule for the removed VLAN ID if
+	 * all-multicast is enabled.
+	 */
+	if (vsi->current_netdev_flags & IFF_ALLMULTI)
+		ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
+					   ICE_MCAST_VLAN_PROMISC_BITS, vid);
+
+	if (vsi->num_vlan == 1) {
+		/* Disable pruning when VLAN 0 is the only VLAN rule */
+		if (ice_vsi_is_vlan_pruning_ena(vsi))
+			ice_cfg_vlan_pruning(vsi, false);
+
+		/* Update look-up type of multicast promisc rule for VLAN 0
+		 * from ICE_SW_LKUP_PROMISC_VLAN to ICE_SW_LKUP_PROMISC when
+		 * all-multicast is enabled and VLAN 0 is the only VLAN rule.
+		 */
+		if (vsi->current_netdev_flags & IFF_ALLMULTI) {
+			ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
+						   ICE_MCAST_VLAN_PROMISC_BITS,
+						   0);
+			ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
+						 ICE_MCAST_PROMISC_BITS, 0);
+		}
+	}
+
+finish:
+	clear_bit(ICE_CFG_BUSY, vsi->state);
 
-	set_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
 	return ret;
 }
 
#2 lore raw
In reply to Ivan Vecera
Quoted 280 lines · Ivan Vecera

Handling of all-multicast flag and associated multicast promiscuous mode is broken in ice driver. When a user switches allmulticast flag on or off the driver checks whether any VLANs are configured over the interface (except default VLAN 0).

If any extra VLANs are registered it enables multicast promiscuous mode for all these VLANs (including default VLAN 0) using ICE_SW_LKUP_PROMISC_VLAN look-up type. In this situation all multicast packets tagged with known VLAN ID or untagged are received and multicast packets tagged with unknown VLAN ID ignored.

If no extra VLANs are registered (so only VLAN 0 exists) it enables multicast promiscuous mode for VLAN 0 and uses ICE_SW_LKUP_PROMISC look-up type. In this situation any multicast packets including tagged ones are received.

The driver handles IFF_ALLMULTI in ice_vsi_sync_fltr() this way:

ice_vsi_sync_fltr() {
...

  if (changed_flags & IFF_ALLMULTI) {
    if (netdev->flags & IFF_ALLMULTI) {
      if (vsi->num_vlans > 1)
        ice_set_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
      else
        ice_set_promisc(..., ICE_MCAST_PROMISC_BITS);
    } else {
      if (vsi->num_vlans > 1)
        ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
      else
        ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS);
    }

}
...
}

The code above depends on value vsi->num_vlan that specifies number of VLANs configured over the interface (including VLAN 0) and this is problem because that value is modified in NDO callbacks ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid().

Scenario 1:
1. ip link set ens7f0 allmulticast on
2. ip link add vlan10 link ens7f0 type vlan id 10
3. ip link set ens7f0 allmulticast off
4. ip link set ens7f0 allmulticast on

[1] In this scenario IFF_ALLMULTI is enabled and the driver calls ice_set_promisc(..., ICE_MCAST_PROMISC_BITS) that installs multicast promisc rule with non-VLAN look-up type.
[2] Then VLAN with ID 10 is added and vsi->num_vlan incremented to 2
[3] Command switches IFF_ALLMULTI off and the driver calls ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS) but this call is effectively NOP because it looks for multicast promisc rules for VLAN 0 and VLAN 10 with VLAN look-up type but no such rules exist. So the all-multicast remains enabled silently in hardware.
[4] Command tries to switch IFF_ALLMULTI on and the driver calls ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS) but this call fails (-EEXIST) because non-VLAN multicast promisc rule already exists.

Scenario 2:
1. ip link add vlan10 link ens7f0 type vlan id 10
2. ip link set ens7f0 allmulticast on
3. ip link add vlan20 link ens7f0 type vlan id 20
4. ip link del vlan10 ; ip link del vlan20
5. ip link set ens7f0 allmulticast off

[1] VLAN with ID 10 is added and vsi->num_vlan==2
[2] Command switches IFF_ALLMULTI on and driver installs multicast promisc rules with VLAN look-up type for VLAN 0 and 10
[3] VLAN with ID 20 is added and vsi->num_vlan==3 but no multicast promisc rules is added for this new VLAN so the interface does not receive MC packets from VLAN 20
[4] Both VLANs are removed but multicast rule for VLAN 10 remains installed so interface receives multicast packets from VLAN 10
[5] Command switches IFF_ALLMULTI off and because vsi->num_vlan is 1 the driver tries to remove multicast promisc rule for VLAN 0 with non-VLAN look-up that does not exist. All-multicast looks disabled from user point of view but it is partially enabled in HW (interface receives all multicast packets either untagged or tagged with VLAN ID 10)

To resolve these issues the patch introduces these changes:
1. Adds handling for IFF_ALLMULTI to ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid() callbacks. So when VLAN is added/removed and IFF_ALLMULTI is enabled an appropriate multicast promisc rule for that VLAN ID is added/removed.
2. In ice_vlan_rx_add_vid() when first VLAN besides VLAN 0 is added so (vsi->num_vlan == 2) and IFF_ALLMULTI is enabled then look-up type for existing multicast promisc rule for VLAN 0 is updated to ICE_MCAST_VLAN_PROMISC_BITS.
3. In ice_vlan_rx_kill_vid() when last VLAN besides VLAN 0 is removed so (vsi->num_vlan == 1) and IFF_ALLMULTI is enabled then look-up type for existing multicast promisc rule for VLAN 0 is updated to ICE_MCAST_PROMISC_BITS.
4. Both ice_vlan_rx_{add,kill}_vid() have to run under ICE_CFG_BUSY bit protection to avoid races with ice_vsi_sync_fltr() that runs in ice_service_task() context.
5. Bit ICE_VSI_VLAN_FLTR_CHANGED is use-less and can be removed.
6. Error messages added to ice_fltr_*_vsi_promisc() helper functions to avoid them in their callers
7. Small improvements to increase readability

Fixes 5eda8afd6bcc ("ice: Add support for PF/VF promiscuous mode")
---
 drivers/net/ethernet/intel/ice/ice.h      |   1 -
 drivers/net/ethernet/intel/ice/ice_fltr.c |  52 +++++++++-
 drivers/net/ethernet/intel/ice/ice_main.c | 119 +++++++++++++++-------
 3 files changed, 131 insertions(+), 41 deletions(-)
drivers/net/ethernet/intel/ice/ice.h +0 -1
index bea1d1e39fa2..717542e49d65 100644
@@ -300,7 +300,6 @@ enum ice_vsi_state {
 	ICE_VSI_NETDEV_REGISTERED,
 	ICE_VSI_UMAC_FLTR_CHANGED,
 	ICE_VSI_MMAC_FLTR_CHANGED,
-	ICE_VSI_VLAN_FLTR_CHANGED,
 	ICE_VSI_PROMISC_CHANGED,
 	ICE_VSI_STATE_NBITS		/* must be last */
 };
drivers/net/ethernet/intel/ice/ice_fltr.c +48 -4
index c29177c6bb9d..8ed87b43a367 100644
@@ -58,7 +58,18 @@ int
 ice_fltr_set_vlan_vsi_promisc(struct ice_hw *hw, struct ice_vsi *vsi,
 			      u8 promisc_mask)
 {
-	return ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, false);
+	struct ice_pf *pf = hw->back;
+	int result;
+
+	result = ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, false);
+	if (!result)
+		return result;
+
+	dev_err(ice_pf_to_dev(pf),
+		"Error setting promisc mode on VSI %i (rc=%d)\n", vsi->vsi_num,
+		result);
+
+	return result;
 }
 
 /**
@@ -73,7 +84,18 @@ int
 ice_fltr_clear_vlan_vsi_promisc(struct ice_hw *hw, struct ice_vsi *vsi,
 				u8 promisc_mask)
 {
-	return ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, true);
+	struct ice_pf *pf = hw->back;
+	int result;
+
+	result = ice_set_vlan_vsi_promisc(hw, vsi->idx, promisc_mask, true);
+	if (!result)
+		return result;
+
+	dev_err(ice_pf_to_dev(pf),
+		"Error clearing promisc mode on VSI %i (rc=%d)\n",
+		vsi->vsi_num, result);
+
+	return result;
 }
 
 /**
@@ -87,7 +109,18 @@ int
 ice_fltr_clear_vsi_promisc(struct ice_hw *hw, u16 vsi_handle, u8 promisc_mask,
 			   u16 vid)
 {
-	return ice_clear_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
+	struct ice_pf *pf = hw->back;
+	int result;
+
+	result = ice_clear_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
+	if (!result)
+		return result;
+
+	dev_err(ice_pf_to_dev(pf),
+		"Error clearing promisc mode on VSI %i for VID %u (rc=%d)\n",
+		ice_get_hw_vsi_num(hw, vsi_handle), vid, result);
+
+	return result;
 }
 
 /**
@@ -101,7 +134,18 @@ int
 ice_fltr_set_vsi_promisc(struct ice_hw *hw, u16 vsi_handle, u8 promisc_mask,
 			 u16 vid)
 {
-	return ice_set_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
+	struct ice_pf *pf = hw->back;
+	int result;
+
+	result = ice_set_vsi_promisc(hw, vsi_handle, promisc_mask, vid);
+	if (!result)
+		return result;
+
+	dev_err(ice_pf_to_dev(pf),
+		"Error setting promisc mode on VSI %i for VID %u (rc=%d)\n",
+		ice_get_hw_vsi_num(hw, vsi_handle), vid, result);
+
+	return result;
 }
 
 /**
drivers/net/ethernet/intel/ice/ice_main.c +19 -12
index b7e8744b0c0a..168a41ea37b8 100644
@@ -227,8 +227,7 @@ static int ice_add_mac_to_unsync_list(struct net_device *netdev, const u8 *addr)
 static bool ice_vsi_fltr_changed(struct ice_vsi *vsi)
 {
 	return test_bit(ICE_VSI_UMAC_FLTR_CHANGED, vsi->state) ||
-	       test_bit(ICE_VSI_MMAC_FLTR_CHANGED, vsi->state) ||
-	       test_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
+	       test_bit(ICE_VSI_MMAC_FLTR_CHANGED, vsi->state);
 }
 
 /**
@@ -244,10 +243,15 @@ static int ice_set_promisc(struct ice_vsi *vsi, u8 promisc_m)
 	if (vsi->type != ICE_VSI_PF)
 		return 0;
 
-	if (vsi->num_vlan > 1)
-		status = ice_fltr_set_vlan_vsi_promisc(&vsi->back->hw, vsi, promisc_m);
-	else
-		status = ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx, promisc_m, 0);
+	if (vsi->num_vlan > 1) {
+		promisc_m |= (ICE_PROMISC_VLAN_RX | ICE_PROMISC_VLAN_TX);
+		status = ice_fltr_set_vlan_vsi_promisc(&vsi->back->hw, vsi,
+						       promisc_m);
+	} else {
+		status = ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
+						  promisc_m, 0);
+	}
+
 	return status;
 }
 
@@ -264,10 +268,15 @@ static int ice_clear_promisc(struct ice_vsi *vsi, u8 promisc_m)
 	if (vsi->type != ICE_VSI_PF)
 		return 0;
 
-	if (vsi->num_vlan > 1)
-		status = ice_fltr_clear_vlan_vsi_promisc(&vsi->back->hw, vsi, promisc_m);
-	else
-		status = ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx, promisc_m, 0);
+	if (vsi->num_vlan > 1) {
+		promisc_m |= (ICE_PROMISC_VLAN_RX | ICE_PROMISC_VLAN_TX);
+		status = ice_fltr_clear_vlan_vsi_promisc(&vsi->back->hw, vsi,
+							 promisc_m);
+	} else {
+		status = ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
+						    promisc_m, 0);
+	}
+
 	return status;
 }
 
@@ -285,7 +294,6 @@ static int ice_vsi_sync_fltr(struct ice_vsi *vsi)
 	struct ice_pf *pf = vsi->back;
 	struct ice_hw *hw = &pf->hw;
 	u32 changed_flags = 0;
-	u8 promisc_m;
 	int err;
 
 	if (!vsi->netdev)
@@ -303,7 +311,6 @@ static int ice_vsi_sync_fltr(struct ice_vsi *vsi)
 	if (ice_vsi_fltr_changed(vsi)) {
 		clear_bit(ICE_VSI_UMAC_FLTR_CHANGED, vsi->state);
 		clear_bit(ICE_VSI_MMAC_FLTR_CHANGED, vsi->state);
-		clear_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
 
 		/* grab the netdev's addr_list_lock */
 		netif_addr_lock_bh(netdev);

drivers/net/ethernet/intel/ice/ice_main.c static int ice_vsi_sync_fltr(struct ice_vsi *vsi) · line 358

Quoted 7 lines
drivers/net/ethernet/intel/ice/ice_main.c +0 -4
@@ -352,29 +359,15 @@ static int ice_vsi_sync_fltr(struct ice_vsi *vsi)
 	/* check for changes in promiscuous modes */
 	if (changed_flags & IFF_ALLMULTI) {
 		if (vsi->current_netdev_flags & IFF_ALLMULTI) {
-			if (vsi->num_vlan > 1)
-				promisc_m = ICE_MCAST_VLAN_PROMISC_BITS;
-			else
-				promisc_m = ICE_MCAST_PROMISC_BITS;

Because ice_{set,clear}_promisc() are now always called with the same second argument (ICE_MCAST_PROMISC_BITS), wouldn't it be better to remove the arg and instead call ice_fltr_{clear,set}_{vlan,vsi}_vsi_promisc() with either ICE_MCAST_VLAN_PROMISC_BITS or ICE_MCAST_PROMISC_BITS inside the function?

Quoted 93 lines
drivers/net/ethernet/intel/ice/ice_main.c +38 -19
-
-			err = ice_set_promisc(vsi, promisc_m);
+			err = ice_set_promisc(vsi, ICE_MCAST_PROMISC_BITS);>  			if (err) {
-				netdev_err(netdev, "Error setting Multicast promiscuous mode on VSI %i\n",
-					   vsi->vsi_num);
 				vsi->current_netdev_flags &= ~IFF_ALLMULTI;
 				goto out_promisc;
 			}
 		} else {
 			/* !(vsi->current_netdev_flags & IFF_ALLMULTI) */
-			if (vsi->num_vlan > 1)
-				promisc_m = ICE_MCAST_VLAN_PROMISC_BITS;
-			else
-				promisc_m = ICE_MCAST_PROMISC_BITS;
-
-			err = ice_clear_promisc(vsi, promisc_m);
+			err = ice_clear_promisc(vsi, ICE_MCAST_PROMISC_BITS);
 			if (err) {
-				netdev_err(netdev, "Error clearing Multicast promiscuous mode on VSI %i\n",
-					   vsi->vsi_num);
 				vsi->current_netdev_flags |= IFF_ALLMULTI;
 				goto out_promisc;
 			}
@@ -3445,19 +3438,47 @@ ice_vlan_rx_add_vid(struct net_device *netdev, __always_unused __be16 proto,
 	if (!vid)
 		return 0;
 
+	while (test_and_set_bit(ICE_CFG_BUSY, vsi->state))
+		usleep_range(1000, 2000);
+
 	/* Enable VLAN pruning when a VLAN other than 0 is added */
 	if (!ice_vsi_is_vlan_pruning_ena(vsi)) {
 		ret = ice_cfg_vlan_pruning(vsi, true);
 		if (ret)
-			return ret;
+			goto finish;
+	}
+
+	/* Add multicast promisc rule for the VLAN ID to be added if
+	 * all-multicast is currently enabled.
+	 */
+	if (vsi->current_netdev_flags & IFF_ALLMULTI) {
+		ret = ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
+					       ICE_MCAST_VLAN_PROMISC_BITS,
+					       vid);
+		if (ret)
+			goto finish;
 	}
 
 	/* Add a switch rule for this VLAN ID so its corresponding VLAN tagged
 	 * packets aren't pruned by the device's internal switch on Rx
 	 */
 	ret = ice_vsi_add_vlan(vsi, vid, ICE_FWD_TO_VSI);
-	if (!ret)
-		set_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
+	if (ret)
+		goto finish;
+
+	/* If all-multicast is currently enabled and this VLAN ID is only one
+	 * besides VLAN-0 we have to update look-up type of multicast promisc
+	 * rule for VLAN-0 from ICE_SW_LKUP_PROMISC to ICE_SW_LKUP_PROMISC_VLAN.
+	 */
+	if ((vsi->current_netdev_flags & IFF_ALLMULTI) && vsi->num_vlan == 2) {
+		ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
+					   ICE_MCAST_PROMISC_BITS, 0);
+		ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
+					 ICE_MCAST_VLAN_PROMISC_BITS, 0);
+	}
+
+finish:
+	clear_bit(ICE_CFG_BUSY, vsi->state);
 
 	return ret;
 }
@@ -3482,18 +3503,44 @@ ice_vlan_rx_kill_vid(struct net_device *netdev, __always_unused __be16 proto,
 	if (!vid)
 		return 0;
 
+	while (test_and_set_bit(ICE_CFG_BUSY, vsi->state))
+		usleep_range(1000, 2000);
+
 	/* Make sure ice_vsi_kill_vlan is successful before updating VLAN
 	 * information
 	 */
 	ret = ice_vsi_kill_vlan(vsi, vid);
 	if (ret)
-		return ret;
+		goto finish;
 
-	/* Disable pruning when VLAN 0 is the only VLAN rule */
-	if (vsi->num_vlan == 1 && ice_vsi_is_vlan_pruning_ena(vsi))
-		ret = ice_cfg_vlan_pruning(vsi, false);
+	/* Remove multicast promisc rule for the removed VLAN ID if

drivers/net/ethernet/intel/ice/ice_main.c ice_vlan_rx_kill_vid(struct net_device *netdev, __always_unused __be16 proto, · line 3526

Quoted 10 lines
drivers/net/ethernet/intel/ice/ice_main.c +10 -0
+	 * all-multicast is enabled.
+	 */
+	if (vsi->current_netdev_flags & IFF_ALLMULTI)
+		ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
+					   ICE_MCAST_VLAN_PROMISC_BITS, vid);
+
+	if (vsi->num_vlan == 1) {
+		/* Disable pruning when VLAN 0 is the only VLAN rule */
+		if (ice_vsi_is_vlan_pruning_ena(vsi))
+			ice_cfg_vlan_pruning(vsi, false);

Why was ret = ... removed here?

Quoted 11 lines
drivers/net/ethernet/intel/ice/ice_main.c +11 -0
+
+		/* Update look-up type of multicast promisc rule for VLAN 0
+		 * from ICE_SW_LKUP_PROMISC_VLAN to ICE_SW_LKUP_PROMISC when
+		 * all-multicast is enabled and VLAN 0 is the only VLAN rule.
+		 */
+		if (vsi->current_netdev_flags & IFF_ALLMULTI) {
+			ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
+						   ICE_MCAST_VLAN_PROMISC_BITS,
+						   0);
+			ice_fltr_set_vsi_promisc(&vsi->back->hw, vsi->idx,
+						 ICE_MCAST_PROMISC_BITS, 0);

drivers/net/ethernet/intel/ice/ice_main.c ice_vlan_rx_kill_vid(struct net_device *netdev, __always_unused __be16 proto, · line 3546

Quoted 10 lines
drivers/net/ethernet/intel/ice/ice_main.c +5 -1
+		}
+	}
+
+finish:
+	clear_bit(ICE_CFG_BUSY, vsi->state);
 
-	set_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
 	return ret;
 }
 

Otherwise LGTM (though my experience in this area is rather limited).

Marcin

#3 lore raw
Quoted 10 lines · On Wed, 23 Mar 2022 21:05:20 +0100 Marcin Szycik…

drivers/net/ethernet/intel/ice/ice_main.c static int ice_vsi_sync_fltr(struct ice_vsi *vsi) · line 358

Quoted 8 lines
drivers/net/ethernet/intel/ice/ice_main.c +0 -4
@@ -352,29 +359,15 @@ static int ice_vsi_sync_fltr(struct ice_vsi *vsi)
 	/* check for changes in promiscuous modes */
 	if (changed_flags & IFF_ALLMULTI) {
 		if (vsi->current_netdev_flags & IFF_ALLMULTI) {
-			if (vsi->num_vlan > 1)
-				promisc_m = ICE_MCAST_VLAN_PROMISC_BITS;
-			else
-				promisc_m = ICE_MCAST_PROMISC_BITS;  

Because ice_{set,clear}_promisc() are now always called with the same second argument (ICE_MCAST_PROMISC_BITS), wouldn't it be better to remove the arg and instead call ice_fltr_{clear,set}_{vlan,vsi}_vsi_promisc() with either ICE_MCAST_VLAN_PROMISC_BITS or ICE_MCAST_PROMISC_BITS inside the function?

Because ice_{set,clear}_promisc() then could be used only for set mcast prosmisc mode so I modified them only to automatically insert ICE_PROMISC_VLAN_RX & ICE_PROMISC_VLAN_TX based on vsi->num_vlan value.

Anyway I will fix some objections from Jacob and send v2.

Thanks,
Ivan

#4 lore raw
In reply to Marcin Szycik
Quoted 15 lines · On Wed, 23 Mar 2022 21:05:20 +0100 Marcin Szycik…
Quoted 15 lines
drivers/net/ethernet/intel/ice/ice_main.c +4 -1
@@ -3482,18 +3503,44 @@ ice_vlan_rx_kill_vid(struct net_device *netdev, __always_unused __be16 proto,
 	if (!vid)
 		return 0;
 
+	while (test_and_set_bit(ICE_CFG_BUSY, vsi->state))
+		usleep_range(1000, 2000);
+
 	/* Make sure ice_vsi_kill_vlan is successful before updating VLAN
 	 * information
 	 */
 	ret = ice_vsi_kill_vlan(vsi, vid);
 	if (ret)
-		return ret;
+		goto finish;
 
Quoted 16 lines
Quoted 4 lines
drivers/net/ethernet/intel/ice/ice_main.c +1 -3
-	/* Disable pruning when VLAN 0 is the only VLAN rule */
-	if (vsi->num_vlan == 1 && ice_vsi_is_vlan_pruning_ena(vsi))
-		ret = ice_cfg_vlan_pruning(vsi, false);
+	/* Remove multicast promisc rule for the removed VLAN ID if

drivers/net/ethernet/intel/ice/ice_main.c ice_vlan_rx_kill_vid(struct net_device *netdev, __always_unused __be16 proto, · line 3526

Quoted 10 lines
drivers/net/ethernet/intel/ice/ice_main.c +10 -0
+	 * all-multicast is enabled.
+	 */
+	if (vsi->current_netdev_flags & IFF_ALLMULTI)
+		ice_fltr_clear_vsi_promisc(&vsi->back->hw, vsi->idx,
+					   ICE_MCAST_VLAN_PROMISC_BITS, vid);
+
+	if (vsi->num_vlan == 1) {
+		/* Disable pruning when VLAN 0 is the only VLAN rule */
+		if (ice_vsi_is_vlan_pruning_ena(vsi))
+			ice_cfg_vlan_pruning(vsi, false);  

Why was ret = ... removed here?

Because we are in ice_vlan_rx_kill_vid() that is used to remove VLAN and at this the VLAN ID was removed from VLAN filter so we cannot return value other than 0. Network stack would think that the VLAN ID is still present in VLAN filter.

Ivan