Skip to contentSkip to conversation

iio: adc: introduce Qualcomm SPMI Round Robin ADC

PATCH Superseded Caleb Connolly 6 participants 26 messages Mar 23, 2022 – Apr 29, 2022

Subsystems (6)

v13 of 14 Superseded Latest is v14 →

lore
Share & tools
lore
#0 lore raw

v13 cover iio: adc: introduce Qualcomm SPMI Round Robin ADC

The RRADC is responsible for reading data about the current and voltage from the USB or DC in jacks, it can also read the battery ID (resistence) and some temperatures. It is found on the PMI8998 and PM660 Qualcomm PMICs.

The RRADC has to calibrate some ADC values based on which chip fab the PMIC was produced in, to facilitate this the patches ("mfd: qcom-spmi-pmic: expose the PMIC revid information to clients") and ("mfd: qcom-spmi-pmic: read fab id on supported PMICs") expose the PMIC revision information and fab_id as a struct and register them as driver data in the Qualcomm SPMI PMIC driver so that it can be read by the RRADC.

The first 3 patches add support for looking up an SPMI device from a struct device_node, as well as introducing support for looking up the base USID of a Qcom PMIC, see patch comments for more details. These Address Bjorns comments on v2.

Changes since v12:
* Apply Krzysztof's suggestions to rradc DT binding docs.

Changes since v11:
* Remove debug logging which was left in ("mfd: qcom-spmi-pmic: expose the PMIC revid information to clients")
* Picked up Dmitry's Tested-by and Reviewed-by tags.

Changes since v10:
* Don't inline spmi_device_from_of()

Changes since v9:
* Add back missing copyright, this driver is originally derived from downstream (Thanks Manivannan).

Changes since v8:
* Drop Reported-by for the bugfix on previous revision reported by LKP
* Apply Jonathans suggestions
* Rework patch 2 ("expose the PMIC revid information to clients") to handle PMICs with a single USID (thanks Dmitry)

Changes since v7:
* Addressed Jonathans comments
* Fixed bug reported by LKP

Changes since v6:
* Fix printf format warning in rradc

Changes since v5:
* Add missing EXPORT_SYMBOL_GPL() to
("spmi: add a helper to look up an SPMI device from a device node")

Changes since v4:
* Addressed Jonathan's comments on v4
* Reworked the qcom-spmi-pmic patches to properly walk the devicetree to find the base USID. I've tested this on SDM845 which has two PMICs (pm8998 and pmi8998) and I'm able to look up the PMIC revid from all 4 USIDs.

Changes since v3:
* Split PMIC patch in two, rework to support function drivers on a sibling USID
* Completely rework RRADC driver to make use of the modern IIO framework. This required re-arranging a lot of the equations and results in some lost precision, where relevant I've left comments to explain this. I don't think any of it is significant enough to justify doing post-processing in driver.
Thanks a lot Jonathan and John Stultz for helping me out with this

Changes since v2:
* Add missing include (thanks kernel test robot :D)
* Rework some confusing function return values, specifically rradc_read_status_in_cont_mode and rradc_prepare_batt_id_conversion both of which didn't correctly handle "ret". This also bought up an issue as the previous implementation didn't actually wait for the channel to be ready. It doesn't seem like that's strictly necessary (same data is reported if I wait for the status to be good or not) but I've included it anyway for good measure.

Changes since v1:
* Rework the RRADC driver based on Jonathan's feedback
* Pick up Rob's reviewed by for the dt-binding patch.
---
Caleb Connolly (9):
spmi: add a helper to look up an SPMI device from a device node
mfd: qcom-spmi-pmic: expose the PMIC revid information to clients
mfd: qcom-spmi-pmic: read fab id on supported PMICs
dt-bindings: iio: adc: document qcom-spmi-rradc
iio: adc: qcom-spmi-rradc: introduce round robin adc
arm64: dts: qcom: pmi8998: add rradc node
arm64: dts: qcom: sdm845-oneplus: enable rradc
arm64: dts: qcom: sdm845-db845c: enable rradc
arm64: dts: qcom: sdm845-xiaomi-beryllium: enable rradc

 .../bindings/iio/adc/qcom,spmi-rradc.yaml     |   51 +
 arch/arm64/boot/dts/qcom/pmi8998.dtsi         |    8 +
 arch/arm64/boot/dts/qcom/sdm845-db845c.dts    |    4 +
 .../boot/dts/qcom/sdm845-oneplus-common.dtsi  |    4 +
 .../boot/dts/qcom/sdm845-xiaomi-beryllium.dts |    4 +
 drivers/iio/adc/Kconfig                       |   12 +
 drivers/iio/adc/Makefile                      |    1 +
 drivers/iio/adc/qcom-spmi-rradc.c             | 1021 +++++++++++++++++
 drivers/mfd/qcom-spmi-pmic.c                  |  268 +++--
 drivers/spmi/spmi.c                           |   17 +
 include/linux/spmi.h                          |    3 +
 include/soc/qcom/qcom-spmi-pmic.h             |   61 +
 12 files changed, 1364 insertions(+), 90 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-rradc.yaml
 create mode 100644 drivers/iio/adc/qcom-spmi-rradc.c
 create mode 100644 include/soc/qcom/qcom-spmi-pmic.h
Signature · 1 line
2.35.1
#1 lore raw

PATCH v13 1/9 spmi: add a helper to look up an SPMI device from a device node

From: Caleb Connolly <[email protected]>

The helper function spmi_device_from_of() takes a device node and returns the SPMI device associated with it.
This is like of_find_device_by_node but for SPMI devices.

---
 drivers/spmi/spmi.c  | 17 +++++++++++++++++
 include/linux/spmi.h |  3 +++
 2 files changed, 20 insertions(+)
drivers/spmi/spmi.c +17 -0
index b37ead9e2fad..a456ce5141e1 100644
@@ -386,6 +386,23 @@ static struct bus_type spmi_bus_type = {
 	.uevent		= spmi_drv_uevent,
 };
 
+/**
+ * spmi_device_from_of() - get the associated SPMI device from a device node
+ *
+ * @np:		device node
+ *
+ * Returns the struct spmi_device associated with a device node or NULL.
+ */
+struct spmi_device *spmi_device_from_of(struct device_node *np)
+{
+	struct device *dev = bus_find_device_by_of_node(&spmi_bus_type, np);
+
+	if (dev)
+		return to_spmi_device(dev);
+	return NULL;
+}
+EXPORT_SYMBOL_GPL(spmi_device_from_of);
+
 /**
  * spmi_controller_alloc() - Allocate a new SPMI device
  * @ctrl:	associated controller
include/linux/spmi.h +3 -0
index 729bcbf9f5ad..eac1956a8727 100644
@@ -164,6 +164,9 @@ static inline void spmi_driver_unregister(struct spmi_driver *sdrv)
 	module_driver(__spmi_driver, spmi_driver_register, \
 			spmi_driver_unregister)
 
+struct device_node;
+
+struct spmi_device *spmi_device_from_of(struct device_node *np);
 int spmi_register_read(struct spmi_device *sdev, u8 addr, u8 *buf);
 int spmi_ext_register_read(struct spmi_device *sdev, u8 addr, u8 *buf,
 			   size_t len);
Signature · 1 line
2.35.1
#2 lore raw

PATCH v13 2/9 mfd: qcom-spmi-pmic: expose the PMIC revid information to clients

In reply to Caleb Connolly

From: Caleb Connolly <[email protected]>

Some PMIC functions such as the RRADC need to be aware of the PMIC chip revision information to implement errata or otherwise adjust behaviour, export the PMIC information to enable this.

This is specifically required to enable the RRADC to adjust coefficients based on which chip fab the PMIC was produced in, this can vary per unique device and therefore has to be read at runtime.

---
 drivers/mfd/qcom-spmi-pmic.c      | 261 +++++++++++++++++++-----------
 include/soc/qcom/qcom-spmi-pmic.h |  60 +++++++
 2 files changed, 231 insertions(+), 90 deletions(-)
 create mode 100644 include/soc/qcom/qcom-spmi-pmic.h
drivers/mfd/qcom-spmi-pmic.c +171 -90
index 1cacc00aa6c9..d8e54d9d3448 100644
@@ -3,11 +3,16 @@
  * Copyright (c) 2014, The Linux Foundation. All rights reserved.
  */
 
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/gfp.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/spmi.h>
+#include <linux/types.h>
 #include <linux/regmap.h>
 #include <linux/of_platform.h>
+#include <soc/qcom/qcom-spmi-pmic.h>
 
 #define PMIC_REV2		0x101
 #define PMIC_REV3		0x102
@@ -17,106 +22,151 @@
 
 #define PMIC_TYPE_VALUE		0x51
 
-#define COMMON_SUBTYPE		0x00
-#define PM8941_SUBTYPE		0x01
-#define PM8841_SUBTYPE		0x02
-#define PM8019_SUBTYPE		0x03
-#define PM8226_SUBTYPE		0x04
-#define PM8110_SUBTYPE		0x05
-#define PMA8084_SUBTYPE		0x06
-#define PMI8962_SUBTYPE		0x07
-#define PMD9635_SUBTYPE		0x08
-#define PM8994_SUBTYPE		0x09
-#define PMI8994_SUBTYPE		0x0a
-#define PM8916_SUBTYPE		0x0b
-#define PM8004_SUBTYPE		0x0c
-#define PM8909_SUBTYPE		0x0d
-#define PM8028_SUBTYPE		0x0e
-#define PM8901_SUBTYPE		0x0f
-#define PM8950_SUBTYPE		0x10
-#define PMI8950_SUBTYPE		0x11
-#define PM8998_SUBTYPE		0x14
-#define PMI8998_SUBTYPE		0x15
-#define PM8005_SUBTYPE		0x18
-#define PM660L_SUBTYPE		0x1A
-#define PM660_SUBTYPE		0x1B
-#define PM8150_SUBTYPE		0x1E
-#define PM8150L_SUBTYPE		0x1f
-#define PM8150B_SUBTYPE		0x20
-#define PMK8002_SUBTYPE		0x21
-#define PM8009_SUBTYPE		0x24
-#define PM8150C_SUBTYPE		0x26
-#define SMB2351_SUBTYPE		0x29
+struct qcom_spmi_dev {
+	int num_usids;
+	struct qcom_spmi_pmic pmic;
+};
+
+#define N_USIDS(n)		((void *)n)
 
 static const struct of_device_id pmic_spmi_id_table[] = {
-	{ .compatible = "qcom,pm660",     .data = (void *)PM660_SUBTYPE },
-	{ .compatible = "qcom,pm660l",    .data = (void *)PM660L_SUBTYPE },
-	{ .compatible = "qcom,pm8004",    .data = (void *)PM8004_SUBTYPE },
-	{ .compatible = "qcom,pm8005",    .data = (void *)PM8005_SUBTYPE },
-	{ .compatible = "qcom,pm8019",    .data = (void *)PM8019_SUBTYPE },
-	{ .compatible = "qcom,pm8028",    .data = (void *)PM8028_SUBTYPE },
-	{ .compatible = "qcom,pm8110",    .data = (void *)PM8110_SUBTYPE },
-	{ .compatible = "qcom,pm8150",    .data = (void *)PM8150_SUBTYPE },
-	{ .compatible = "qcom,pm8150b",   .data = (void *)PM8150B_SUBTYPE },
-	{ .compatible = "qcom,pm8150c",   .data = (void *)PM8150C_SUBTYPE },
-	{ .compatible = "qcom,pm8150l",   .data = (void *)PM8150L_SUBTYPE },
-	{ .compatible = "qcom,pm8226",    .data = (void *)PM8226_SUBTYPE },
-	{ .compatible = "qcom,pm8841",    .data = (void *)PM8841_SUBTYPE },
-	{ .compatible = "qcom,pm8901",    .data = (void *)PM8901_SUBTYPE },
-	{ .compatible = "qcom,pm8909",    .data = (void *)PM8909_SUBTYPE },
-	{ .compatible = "qcom,pm8916",    .data = (void *)PM8916_SUBTYPE },
-	{ .compatible = "qcom,pm8941",    .data = (void *)PM8941_SUBTYPE },
-	{ .compatible = "qcom,pm8950",    .data = (void *)PM8950_SUBTYPE },
-	{ .compatible = "qcom,pm8994",    .data = (void *)PM8994_SUBTYPE },
-	{ .compatible = "qcom,pm8998",    .data = (void *)PM8998_SUBTYPE },
-	{ .compatible = "qcom,pma8084",   .data = (void *)PMA8084_SUBTYPE },
-	{ .compatible = "qcom,pmd9635",   .data = (void *)PMD9635_SUBTYPE },
-	{ .compatible = "qcom,pmi8950",   .data = (void *)PMI8950_SUBTYPE },
-	{ .compatible = "qcom,pmi8962",   .data = (void *)PMI8962_SUBTYPE },
-	{ .compatible = "qcom,pmi8994",   .data = (void *)PMI8994_SUBTYPE },
-	{ .compatible = "qcom,pmi8998",   .data = (void *)PMI8998_SUBTYPE },
-	{ .compatible = "qcom,pmk8002",   .data = (void *)PMK8002_SUBTYPE },
-	{ .compatible = "qcom,smb2351",   .data = (void *)SMB2351_SUBTYPE },
-	{ .compatible = "qcom,spmi-pmic", .data = (void *)COMMON_SUBTYPE },
+	{ .compatible = "qcom,pm660", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm660l", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8004", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8005", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8019", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8028", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8110", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150b", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150c", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150l", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8226", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8841", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8901", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8909", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8916", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8941", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8950", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8994", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8998", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pma8084", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmd9635", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmi8950", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmi8962", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmi8994", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmi8998", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmk8002", .data = N_USIDS(2) },
+	{ .compatible = "qcom,smb2351", .data = N_USIDS(2) },
+	{ .compatible = "qcom,spmi-pmic", .data = N_USIDS(1) },
 	{ }
 };
 
-static void pmic_spmi_show_revid(struct regmap *map, struct device *dev)
+#undef N_USIDS
+
+/*
+ * A PMIC can be represented by multiple SPMI devices, but
+ * only the base PMIC device will contain a reference to
+ * the revision information.
+ *
+ * This function takes a pointer to a function device and
+ * returns a pointer to the base PMIC device.
+ *
+ * This only supports PMICs with 1 or 2 USIDs.
+ */
+static struct spmi_device *qcom_pmic_get_base_usid(struct device *dev)
 {
-	unsigned int rev2, minor, major, type, subtype;
-	const char *name = "unknown";
-	int ret, i;
+	struct spmi_device *sdev;
+	struct qcom_spmi_dev *ctx;
+	struct device_node *spmi_bus;
+	struct device_node *other_usid = NULL;
+	int function_parent_usid, ret;
+	u32 pmic_addr;
 
-	ret = regmap_read(map, PMIC_TYPE, &type);
-	if (ret < 0)
-		return;
+	if (!of_match_device(pmic_spmi_id_table, dev))
+		return ERR_PTR(-EINVAL);
+
+	sdev = to_spmi_device(dev);
+	ctx = spmi_device_get_drvdata(sdev);
+
+	/*
+	 * Quick return if the function device is already in the base
+	 * USID. This will always be hit for PMICs with only 1 USID.
+	 */
+	if (sdev->usid % ctx->num_usids == 0)
+		return sdev;
+
+	function_parent_usid = sdev->usid;
+
+	/*
+	 * Walk through the list of PMICs until we find the sibling USID.
+	 * The goal is to find the first USID which is less than the
+	 * number of USIDs in the PMIC away, e.g. for a PMIC with 2 USIDs
+	 * where the function device is under USID 3, we want to find the
+	 * device for USID 2.
+	 */
+	spmi_bus = of_get_parent(sdev->dev.of_node);
+	do {
+		other_usid = of_get_next_child(spmi_bus, other_usid);
+		ret = of_property_read_u32_index(other_usid, "reg", 0, &pmic_addr);
+		if (ret)
+			return ERR_PTR(ret);
+		sdev = spmi_device_from_of(other_usid);
+		if (sdev == NULL) {
+			/*
+			 * If the base USID for this PMIC hasn't probed yet
+			 * but the secondary USID has, then we need to defer
+			 * the function driver so that it will attempt to
+			 * probe again when the base USID is ready.
+			 */
+			if (pmic_addr == function_parent_usid  - (ctx->num_usids - 1))
+				return ERR_PTR(-EPROBE_DEFER);
+
+			continue;
+		}
+
+		if (pmic_addr == function_parent_usid  - (ctx->num_usids - 1))
+			return sdev;
+	} while (other_usid->sibling);
+
+	return ERR_PTR(-ENODATA);
+}
+
+static inline void pmic_print_info(struct device *dev, struct qcom_spmi_pmic *pmic)
+{
+	dev_dbg(dev, "%x: %s v%d.%d\n",
+		pmic->subtype, pmic->name, pmic->major, pmic->minor);
+}
 
-	if (type != PMIC_TYPE_VALUE)
-		return;
+static int pmic_spmi_load_revid(struct regmap *map, struct device *dev,
+				 struct qcom_spmi_pmic *pmic)
+{
+	int ret;
 
-	ret = regmap_read(map, PMIC_SUBTYPE, &subtype);
+	ret = regmap_read(map, PMIC_TYPE, &pmic->type);
 	if (ret < 0)
-		return;
+		return ret;
 
-	for (i = 0; i < ARRAY_SIZE(pmic_spmi_id_table); i++) {
-		if (subtype == (unsigned long)pmic_spmi_id_table[i].data)
-			break;
-	}
+	if (pmic->type != PMIC_TYPE_VALUE)
+		return ret;
 
-	if (i != ARRAY_SIZE(pmic_spmi_id_table))
-		name = pmic_spmi_id_table[i].compatible;
+	ret = regmap_read(map, PMIC_SUBTYPE, &pmic->subtype);
+	if (ret < 0)
+		return ret;
+
+	pmic->name = of_match_device(pmic_spmi_id_table, dev)->compatible;
 
-	ret = regmap_read(map, PMIC_REV2, &rev2);
+	ret = regmap_read(map, PMIC_REV2, &pmic->rev2);
 	if (ret < 0)
-		return;
+		return ret;
 
-	ret = regmap_read(map, PMIC_REV3, &minor);
+	ret = regmap_read(map, PMIC_REV3, &pmic->minor);
 	if (ret < 0)
-		return;
+		return ret;
 
-	ret = regmap_read(map, PMIC_REV4, &major);
+	ret = regmap_read(map, PMIC_REV4, &pmic->major);
 	if (ret < 0)
-		return;
+		return ret;
 
 	/*
 	 * In early versions of PM8941 and PM8226, the major revision number
@@ -124,15 +174,34 @@ static void pmic_spmi_show_revid(struct regmap *map, struct device *dev)
 	 * Increment the major revision number here if the chip is an early
 	 * version of PM8941 or PM8226.
 	 */
-	if ((subtype == PM8941_SUBTYPE || subtype == PM8226_SUBTYPE) &&
-	    major < 0x02)
-		major++;
+	if ((pmic->subtype == PM8941_SUBTYPE || pmic->subtype == PM8226_SUBTYPE) &&
+	    pmic->major < 0x02)
+		pmic->major++;
+
+	if (pmic->subtype == PM8110_SUBTYPE)
+		pmic->minor = pmic->rev2;
+
+	pmic_print_info(dev, pmic);
 
-	if (subtype == PM8110_SUBTYPE)
-		minor = rev2;
+	return 0;
+}
+
+/**
+ * qcom_pmic_get() - Get a pointer to the base PMIC device
+ *
+ * @dev: the pmic function device
+ * @return: the struct qcom_spmi_pmic* pointer associated with the function device
+ */
+inline const struct qcom_spmi_pmic *qcom_pmic_get(struct device *dev)
+{
+	struct spmi_device *sdev = qcom_pmic_get_base_usid(dev->parent);
 
-	dev_dbg(dev, "%x: %s v%d.%d\n", subtype, name, major, minor);
+	if (IS_ERR(sdev))
+		return ERR_CAST(sdev);
+
+	return &((struct qcom_spmi_dev *)spmi_device_get_drvdata(sdev))->pmic;
 }
+EXPORT_SYMBOL(qcom_pmic_get);
 
 static const struct regmap_config spmi_regmap_config = {
 	.reg_bits	= 16,
@@ -144,14 +213,26 @@ static const struct regmap_config spmi_regmap_config = {
 static int pmic_spmi_probe(struct spmi_device *sdev)
 {
 	struct regmap *regmap;
+	struct qcom_spmi_dev *ctx;
+	int ret;
 
 	regmap = devm_regmap_init_spmi_ext(sdev, &spmi_regmap_config);
 	if (IS_ERR(regmap))
 		return PTR_ERR(regmap);
 
+	ctx = devm_kzalloc(&sdev->dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	ctx->num_usids = (long)of_device_get_match_data(&sdev->dev);
+
 	/* Only the first slave id for a PMIC contains this information */
-	if (sdev->usid % 2 == 0)
-		pmic_spmi_show_revid(regmap, &sdev->dev);
+	if (sdev->usid % ctx->num_usids == 0) {
+		ret = pmic_spmi_load_revid(regmap, &sdev->dev, &ctx->pmic);
+		if (ret < 0)
+			return ret;
+	}
+	spmi_device_set_drvdata(sdev, ctx);
 
 	return devm_of_platform_populate(&sdev->dev);
 }
include/soc/qcom/qcom-spmi-pmic.h new file +60 -0

60 lines not on this page · raw message

Signature · 1 line
2.35.1
#3 lore raw

Re: [PATCH v13 2/9] mfd: qcom-spmi-pmic: expose the PMIC revid information to clients

Quoted 11 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

Some PMIC functions such as the RRADC need to be aware of the PMIC chip revision information to implement errata or otherwise adjust behaviour, export the PMIC information to enable this.

This is specifically required to enable the RRADC to adjust coefficients based on which chip fab the PMIC was produced in, this can vary per unique device and therefore has to be read at runtime.

Quoted 8 lines
---
 drivers/mfd/qcom-spmi-pmic.c      | 261 +++++++++++++++++++-----------
 include/soc/qcom/qcom-spmi-pmic.h |  60 +++++++
 2 files changed, 231 insertions(+), 90 deletions(-)
 create mode 100644 include/soc/qcom/qcom-spmi-pmic.h

Apologies for the delay. I've been snowed under.

Quoted 116 lines
drivers/mfd/qcom-spmi-pmic.c +35 -59
index 1cacc00aa6c9..d8e54d9d3448 100644
@@ -3,11 +3,16 @@
  * Copyright (c) 2014, The Linux Foundation. All rights reserved.
  */
 
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/gfp.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/spmi.h>
+#include <linux/types.h>
 #include <linux/regmap.h>
 #include <linux/of_platform.h>
+#include <soc/qcom/qcom-spmi-pmic.h>
 
 #define PMIC_REV2		0x101
 #define PMIC_REV3		0x102
@@ -17,106 +22,151 @@
 
 #define PMIC_TYPE_VALUE		0x51
 
-#define COMMON_SUBTYPE		0x00
-#define PM8941_SUBTYPE		0x01
-#define PM8841_SUBTYPE		0x02
-#define PM8019_SUBTYPE		0x03
-#define PM8226_SUBTYPE		0x04
-#define PM8110_SUBTYPE		0x05
-#define PMA8084_SUBTYPE		0x06
-#define PMI8962_SUBTYPE		0x07
-#define PMD9635_SUBTYPE		0x08
-#define PM8994_SUBTYPE		0x09
-#define PMI8994_SUBTYPE		0x0a
-#define PM8916_SUBTYPE		0x0b
-#define PM8004_SUBTYPE		0x0c
-#define PM8909_SUBTYPE		0x0d
-#define PM8028_SUBTYPE		0x0e
-#define PM8901_SUBTYPE		0x0f
-#define PM8950_SUBTYPE		0x10
-#define PMI8950_SUBTYPE		0x11
-#define PM8998_SUBTYPE		0x14
-#define PMI8998_SUBTYPE		0x15
-#define PM8005_SUBTYPE		0x18
-#define PM660L_SUBTYPE		0x1A
-#define PM660_SUBTYPE		0x1B
-#define PM8150_SUBTYPE		0x1E
-#define PM8150L_SUBTYPE		0x1f
-#define PM8150B_SUBTYPE		0x20
-#define PMK8002_SUBTYPE		0x21
-#define PM8009_SUBTYPE		0x24
-#define PM8150C_SUBTYPE		0x26
-#define SMB2351_SUBTYPE		0x29
+struct qcom_spmi_dev {
+	int num_usids;
+	struct qcom_spmi_pmic pmic;
+};
+
+#define N_USIDS(n)		((void *)n)
 
 static const struct of_device_id pmic_spmi_id_table[] = {
-	{ .compatible = "qcom,pm660",     .data = (void *)PM660_SUBTYPE },
-	{ .compatible = "qcom,pm660l",    .data = (void *)PM660L_SUBTYPE },
-	{ .compatible = "qcom,pm8004",    .data = (void *)PM8004_SUBTYPE },
-	{ .compatible = "qcom,pm8005",    .data = (void *)PM8005_SUBTYPE },
-	{ .compatible = "qcom,pm8019",    .data = (void *)PM8019_SUBTYPE },
-	{ .compatible = "qcom,pm8028",    .data = (void *)PM8028_SUBTYPE },
-	{ .compatible = "qcom,pm8110",    .data = (void *)PM8110_SUBTYPE },
-	{ .compatible = "qcom,pm8150",    .data = (void *)PM8150_SUBTYPE },
-	{ .compatible = "qcom,pm8150b",   .data = (void *)PM8150B_SUBTYPE },
-	{ .compatible = "qcom,pm8150c",   .data = (void *)PM8150C_SUBTYPE },
-	{ .compatible = "qcom,pm8150l",   .data = (void *)PM8150L_SUBTYPE },
-	{ .compatible = "qcom,pm8226",    .data = (void *)PM8226_SUBTYPE },
-	{ .compatible = "qcom,pm8841",    .data = (void *)PM8841_SUBTYPE },
-	{ .compatible = "qcom,pm8901",    .data = (void *)PM8901_SUBTYPE },
-	{ .compatible = "qcom,pm8909",    .data = (void *)PM8909_SUBTYPE },
-	{ .compatible = "qcom,pm8916",    .data = (void *)PM8916_SUBTYPE },
-	{ .compatible = "qcom,pm8941",    .data = (void *)PM8941_SUBTYPE },
-	{ .compatible = "qcom,pm8950",    .data = (void *)PM8950_SUBTYPE },
-	{ .compatible = "qcom,pm8994",    .data = (void *)PM8994_SUBTYPE },
-	{ .compatible = "qcom,pm8998",    .data = (void *)PM8998_SUBTYPE },
-	{ .compatible = "qcom,pma8084",   .data = (void *)PMA8084_SUBTYPE },
-	{ .compatible = "qcom,pmd9635",   .data = (void *)PMD9635_SUBTYPE },
-	{ .compatible = "qcom,pmi8950",   .data = (void *)PMI8950_SUBTYPE },
-	{ .compatible = "qcom,pmi8962",   .data = (void *)PMI8962_SUBTYPE },
-	{ .compatible = "qcom,pmi8994",   .data = (void *)PMI8994_SUBTYPE },
-	{ .compatible = "qcom,pmi8998",   .data = (void *)PMI8998_SUBTYPE },
-	{ .compatible = "qcom,pmk8002",   .data = (void *)PMK8002_SUBTYPE },
-	{ .compatible = "qcom,smb2351",   .data = (void *)SMB2351_SUBTYPE },
-	{ .compatible = "qcom,spmi-pmic", .data = (void *)COMMON_SUBTYPE },
+	{ .compatible = "qcom,pm660", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm660l", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8004", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8005", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8019", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8028", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8110", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150b", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150c", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150l", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8226", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8841", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8901", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8909", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8916", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8941", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8950", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8994", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8998", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pma8084", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmd9635", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmi8950", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmi8962", .data = N_USIDS(2) },

drivers/mfd/qcom-spmi-pmic.c line 65

Quoted 10 lines
drivers/mfd/qcom-spmi-pmic.c +6 -1
+	{ .compatible = "qcom,pmi8994", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmi8998", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmk8002", .data = N_USIDS(2) },
+	{ .compatible = "qcom,smb2351", .data = N_USIDS(2) },
+	{ .compatible = "qcom,spmi-pmic", .data = N_USIDS(1) },
 	{ }
 };
 
-static void pmic_spmi_show_revid(struct regmap *map, struct device *dev)
+#undef N_USIDS

Why is this here? Can't we use a unique macro instead?

Quoted 17 lines
drivers/mfd/qcom-spmi-pmic.c +13 -3
+/*
+ * A PMIC can be represented by multiple SPMI devices, but
+ * only the base PMIC device will contain a reference to
+ * the revision information.
+ *
+ * This function takes a pointer to a function device and
+ * returns a pointer to the base PMIC device.
+ *
+ * This only supports PMICs with 1 or 2 USIDs.
+ */
+static struct spmi_device *qcom_pmic_get_base_usid(struct device *dev)
 {
-	unsigned int rev2, minor, major, type, subtype;
-	const char *name = "unknown";
-	int ret, i;
+	struct spmi_device *sdev;
+	struct qcom_spmi_dev *ctx;

drivers/mfd/qcom-spmi-pmic.c line 87

Quoted 10 lines
drivers/mfd/qcom-spmi-pmic.c +6 -3
+	struct device_node *spmi_bus;
+	struct device_node *other_usid = NULL;
+	int function_parent_usid, ret;
+	u32 pmic_addr;
 
-	ret = regmap_read(map, PMIC_TYPE, &type);
-	if (ret < 0)
-		return;
+	if (!of_match_device(pmic_spmi_id_table, dev))
+		return ERR_PTR(-EINVAL);

Can this happen? How else would the device have been enumerated?

drivers/mfd/qcom-spmi-pmic.c line 90

Quoted 2 lines
drivers/mfd/qcom-spmi-pmic.c +2 -0
+	sdev = to_spmi_device(dev);
+	ctx = spmi_device_get_drvdata(sdev);

This function looks like abstraction for the sake of abstraction.

Why not just use dev_get_drvdata()?

drivers/mfd/qcom-spmi-pmic.c line 104

Quoted 13 lines
drivers/mfd/qcom-spmi-pmic.c +13 -0
+	/*
+	 * Quick return if the function device is already in the base
+	 * USID. This will always be hit for PMICs with only 1 USID.
+	 */
+	if (sdev->usid % ctx->num_usids == 0)
+		return sdev;
+
+	function_parent_usid = sdev->usid;
+
+	/*
+	 * Walk through the list of PMICs until we find the sibling USID.
+	 * The goal is to find the first USID which is less than the
+	 * number of USIDs in the PMIC away, e.g. for a PMIC with 2 USIDs

"array" perhaps?

drivers/mfd/qcom-spmi-pmic.c line 110

Quoted 6 lines
drivers/mfd/qcom-spmi-pmic.c +6 -0
+	 * where the function device is under USID 3, we want to find the
+	 * device for USID 2.
+	 */
+	spmi_bus = of_get_parent(sdev->dev.of_node);
+	do {
+		other_usid = of_get_next_child(spmi_bus, other_usid);

'\n'

drivers/mfd/qcom-spmi-pmic.c line 113

Quoted 3 lines
drivers/mfd/qcom-spmi-pmic.c +3 -0
+		ret = of_property_read_u32_index(other_usid, "reg", 0, &pmic_addr);
+		if (ret)
+			return ERR_PTR(ret);

'\n'

drivers/mfd/qcom-spmi-pmic.c line 115

Quoted 2 lines
drivers/mfd/qcom-spmi-pmic.c +2 -0
+		sdev = spmi_device_from_of(other_usid);
+		if (sdev == NULL) {

if (!sdev)

drivers/mfd/qcom-spmi-pmic.c line 122

Quoted 7 lines
drivers/mfd/qcom-spmi-pmic.c +7 -0
+			/*
+			 * If the base USID for this PMIC hasn't probed yet
+			 * but the secondary USID has, then we need to defer
+			 * the function driver so that it will attempt to
+			 * probe again when the base USID is ready.
+			 */
+			if (pmic_addr == function_parent_usid  - (ctx->num_usids - 1))

Double " ".

Over-bracketing of statements with matching operands.

drivers/mfd/qcom-spmi-pmic.c line 129

Quoted 7 lines
drivers/mfd/qcom-spmi-pmic.c +7 -0
+				return ERR_PTR(-EPROBE_DEFER);
+
+			continue;
+		}
+
+		if (pmic_addr == function_parent_usid  - (ctx->num_usids - 1))
+			return sdev;

Wouldn't it be better written like this:

Quoted 12 lines
drivers/mfd/qcom-spmi-pmic.c +12 -0
+		if (pmic_addr == function_parent_usid - (ctx->num_usids - 1)) {
+		        sdev = spmi_device_from_of(other_usid);
+		        if (!sdev)
+			        /*
+			         * If the base USID for this PMIC hasn't probed yet
+			         * but the secondary USID has, then we need to defer
+			         * the function driver so that it will attempt to
+			         * probe again when the base USID is ready.
+			         */
+				return ERR_PTR(-EPROBE_DEFER);
+                     return sdev;
+		}

[...]

drivers/mfd/qcom-spmi-pmic.c line 139

Quoted 10 lines
drivers/mfd/qcom-spmi-pmic.c +10 -0
+	} while (other_usid->sibling);
+
+	return ERR_PTR(-ENODATA);
+}
+
+static inline void pmic_print_info(struct device *dev, struct qcom_spmi_pmic *pmic)
+{
+	dev_dbg(dev, "%x: %s v%d.%d\n",
+		pmic->subtype, pmic->name, pmic->major, pmic->minor);
+}

More abstraction for no apparent reason.

Quoted 49 lines
drivers/mfd/qcom-spmi-pmic.c +19 -16
-	if (type != PMIC_TYPE_VALUE)
-		return;
+static int pmic_spmi_load_revid(struct regmap *map, struct device *dev,
+				 struct qcom_spmi_pmic *pmic)
+{
+	int ret;
 
-	ret = regmap_read(map, PMIC_SUBTYPE, &subtype);
+	ret = regmap_read(map, PMIC_TYPE, &pmic->type);
 	if (ret < 0)
-		return;
+		return ret;
 
-	for (i = 0; i < ARRAY_SIZE(pmic_spmi_id_table); i++) {
-		if (subtype == (unsigned long)pmic_spmi_id_table[i].data)
-			break;
-	}
+	if (pmic->type != PMIC_TYPE_VALUE)
+		return ret;
 
-	if (i != ARRAY_SIZE(pmic_spmi_id_table))
-		name = pmic_spmi_id_table[i].compatible;
+	ret = regmap_read(map, PMIC_SUBTYPE, &pmic->subtype);
+	if (ret < 0)
+		return ret;
+
+	pmic->name = of_match_device(pmic_spmi_id_table, dev)->compatible;
 
-	ret = regmap_read(map, PMIC_REV2, &rev2);
+	ret = regmap_read(map, PMIC_REV2, &pmic->rev2);
 	if (ret < 0)
-		return;
+		return ret;
 
-	ret = regmap_read(map, PMIC_REV3, &minor);
+	ret = regmap_read(map, PMIC_REV3, &pmic->minor);
 	if (ret < 0)
-		return;
+		return ret;
 
-	ret = regmap_read(map, PMIC_REV4, &major);
+	ret = regmap_read(map, PMIC_REV4, &pmic->major);
 	if (ret < 0)
-		return;
+		return ret;
 
 	/*
 	 * In early versions of PM8941 and PM8226, the major revision number

drivers/mfd/qcom-spmi-pmic.c static void pmic_spmi_show_revid(struct regmap *map, struct device *dev) · line 178

Quoted 8 lines
drivers/mfd/qcom-spmi-pmic.c +2 -3
@@ -124,15 +174,34 @@ static void pmic_spmi_show_revid(struct regmap *map, struct device *dev)
 	 * Increment the major revision number here if the chip is an early
 	 * version of PM8941 or PM8226.
 	 */
-	if ((subtype == PM8941_SUBTYPE || subtype == PM8226_SUBTYPE) &&
-	    major < 0x02)
-		major++;
+	if ((pmic->subtype == PM8941_SUBTYPE || pmic->subtype == PM8226_SUBTYPE) &&
+	    pmic->major < 0x02)

Please define this magic number while you're at it.

Quoted 17 lines
drivers/mfd/qcom-spmi-pmic.c +14 -2
+		pmic->major++;
+
+	if (pmic->subtype == PM8110_SUBTYPE)
+		pmic->minor = pmic->rev2;
+
+	pmic_print_info(dev, pmic);
 
-	if (subtype == PM8110_SUBTYPE)
-		minor = rev2;
+	return 0;
+}
+
+/**
+ * qcom_pmic_get() - Get a pointer to the base PMIC device
+ *
+ * @dev: the pmic function device
+ * @return: the struct qcom_spmi_pmic* pointer associated with the function device

drivers/mfd/qcom-spmi-pmic.c static void pmic_spmi_show_revid(struct regmap *map, struct device *dev) · line 202

Quoted 10 lines
drivers/mfd/qcom-spmi-pmic.c +8 -1
+ */
+inline const struct qcom_spmi_pmic *qcom_pmic_get(struct device *dev)
+{
+	struct spmi_device *sdev = qcom_pmic_get_base_usid(dev->parent);
 
-	dev_dbg(dev, "%x: %s v%d.%d\n", subtype, name, major, minor);
+	if (IS_ERR(sdev))
+		return ERR_CAST(sdev);
+
+	return &((struct qcom_spmi_dev *)spmi_device_get_drvdata(sdev))->pmic;

This is horrible. Please expand it out.

Quoted 11 lines
drivers/mfd/qcom-spmi-pmic.c +3 -0
 }
+EXPORT_SYMBOL(qcom_pmic_get);
 
 static const struct regmap_config spmi_regmap_config = {
 	.reg_bits	= 16,
@@ -144,14 +213,26 @@ static const struct regmap_config spmi_regmap_config = {
 static int pmic_spmi_probe(struct spmi_device *sdev)
 {
 	struct regmap *regmap;
+	struct qcom_spmi_dev *ctx;
+	int ret;

drivers/mfd/qcom-spmi-pmic.c static const struct regmap_config spmi_regmap_config = { · line 227

Quoted 10 lines
drivers/mfd/qcom-spmi-pmic.c +5 -0
 
 	regmap = devm_regmap_init_spmi_ext(sdev, &spmi_regmap_config);
 	if (IS_ERR(regmap))
 		return PTR_ERR(regmap);
 
+	ctx = devm_kzalloc(&sdev->dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	ctx->num_usids = (long)of_device_get_match_data(&sdev->dev);

Why does this need to be long?

In fact, it's not is it? It's an int:

   +struct qcom_spmi_dev {
   +	int num_usids;
   +	struct qcom_spmi_pmic pmic;
   +};
Quoted 18 lines
drivers/mfd/qcom-spmi-pmic.c +6 -2
 	/* Only the first slave id for a PMIC contains this information */
-	if (sdev->usid % 2 == 0)
-		pmic_spmi_show_revid(regmap, &sdev->dev);
+	if (sdev->usid % ctx->num_usids == 0) {
+		ret = pmic_spmi_load_revid(regmap, &sdev->dev, &ctx->pmic);
+		if (ret < 0)
+			return ret;
+	}
+	spmi_device_set_drvdata(sdev, ctx);
 
 	return devm_of_platform_populate(&sdev->dev);
 }
include/soc/qcom/qcom-spmi-pmic.h new file +0 -0
new file mode 100644
index 000000000000..5400e6509fe8

include/soc/qcom/qcom-spmi-pmic.h line 3

Quoted 3 lines
include/soc/qcom/qcom-spmi-pmic.h new file +3 -0
@@ -0,0 +1,60 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Copyright (c) 2021 Linaro. All rights reserved.
+ * Copyright (c) 2021 Caleb Connolly <[email protected]>

Your very own Copyright? Why?

Any not Author: instead?

Quoted 43 lines
include/soc/qcom/qcom-spmi-pmic.h new file +43 -0
+ */
+
+#ifndef __QCOM_SPMI_PMIC_H__
+#define __QCOM_SPMI_PMIC_H__
+
+#define COMMON_SUBTYPE		0x00
+#define PM8941_SUBTYPE		0x01
+#define PM8841_SUBTYPE		0x02
+#define PM8019_SUBTYPE		0x03
+#define PM8226_SUBTYPE		0x04
+#define PM8110_SUBTYPE		0x05
+#define PMA8084_SUBTYPE		0x06
+#define PMI8962_SUBTYPE		0x07
+#define PMD9635_SUBTYPE		0x08
+#define PM8994_SUBTYPE		0x09
+#define PMI8994_SUBTYPE		0x0a
+#define PM8916_SUBTYPE		0x0b
+#define PM8004_SUBTYPE		0x0c
+#define PM8909_SUBTYPE		0x0d
+#define PM8028_SUBTYPE		0x0e
+#define PM8901_SUBTYPE		0x0f
+#define PM8950_SUBTYPE		0x10
+#define PMI8950_SUBTYPE		0x11
+#define PM8998_SUBTYPE		0x14
+#define PMI8998_SUBTYPE		0x15
+#define PM8005_SUBTYPE		0x18
+#define PM660L_SUBTYPE		0x1A
+#define PM660_SUBTYPE		0x1B
+#define PM8150_SUBTYPE		0x1E
+#define PM8150L_SUBTYPE		0x1f
+#define PM8150B_SUBTYPE		0x20
+#define PMK8002_SUBTYPE		0x21
+#define PM8009_SUBTYPE		0x24
+#define PM8150C_SUBTYPE		0x26
+#define SMB2351_SUBTYPE		0x29
+
+#define PMI8998_FAB_ID_SMIC	0x11
+#define PMI8998_FAB_ID_GF	0x30
+
+#define PM660_FAB_ID_GF		0x0
+#define PM660_FAB_ID_TSMC	0x2
+#define PM660_FAB_ID_MX		0x3
+

include/soc/qcom/qcom-spmi-pmic.h line 56

Quoted 10 lines
include/soc/qcom/qcom-spmi-pmic.h new file +10 -0
+struct qcom_spmi_pmic {
+	unsigned int type;
+	unsigned int subtype;
+	unsigned int major;
+	unsigned int minor;
+	unsigned int rev2;
+	const char *name;
+};
+
+struct device;

Can't you just include the correct header?

Quoted 3 lines
include/soc/qcom/qcom-spmi-pmic.h new file +3 -0
+inline const struct qcom_spmi_pmic *qcom_pmic_get(struct device *dev);
+
+#endif /* __QCOM_SPMI_PMIC_H__ */
Signature · 4 lines
Lee Jones [李琼斯]
Principal Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
#4 lore raw

Re: [PATCH v13 2/9] mfd: qcom-spmi-pmic: expose the PMIC revid information to clients

Quoted 22 lines · Lee Jones
Quoted 11 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

Some PMIC functions such as the RRADC need to be aware of the PMIC chip revision information to implement errata or otherwise adjust behaviour, export the PMIC information to enable this.

This is specifically required to enable the RRADC to adjust coefficients based on which chip fab the PMIC was produced in, this can vary per unique device and therefore has to be read at runtime.

Quoted 8 lines
---
  drivers/mfd/qcom-spmi-pmic.c      | 261 +++++++++++++++++++-----------
  include/soc/qcom/qcom-spmi-pmic.h |  60 +++++++
  2 files changed, 231 insertions(+), 90 deletions(-)

create mode 100644 include/soc/qcom/qcom-spmi-pmic.h

Quoted 1 line

Apologies for the delay. I've been snowed under.

Hi Lee,

Thanks a lot for the review, I had a few questions/clarifications

Quoted 125 lines
Quoted 125 lines
drivers/mfd/qcom-spmi-pmic.c +40 -59
index 1cacc00aa6c9..d8e54d9d3448 100644
@@ -3,11 +3,16 @@
   * Copyright (c) 2014, The Linux Foundation. All rights reserved.
   */
 
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/gfp.h>
  #include <linux/kernel.h>
  #include <linux/module.h>
  #include <linux/spmi.h>
+#include <linux/types.h>
  #include <linux/regmap.h>
  #include <linux/of_platform.h>
+#include <soc/qcom/qcom-spmi-pmic.h>
 
  #define PMIC_REV2		0x101
  #define PMIC_REV3		0x102
@@ -17,106 +22,151 @@
 
  #define PMIC_TYPE_VALUE		0x51
 
-#define COMMON_SUBTYPE		0x00
-#define PM8941_SUBTYPE		0x01
-#define PM8841_SUBTYPE		0x02
-#define PM8019_SUBTYPE		0x03
-#define PM8226_SUBTYPE		0x04
-#define PM8110_SUBTYPE		0x05
-#define PMA8084_SUBTYPE		0x06
-#define PMI8962_SUBTYPE		0x07
-#define PMD9635_SUBTYPE		0x08
-#define PM8994_SUBTYPE		0x09
-#define PMI8994_SUBTYPE		0x0a
-#define PM8916_SUBTYPE		0x0b
-#define PM8004_SUBTYPE		0x0c
-#define PM8909_SUBTYPE		0x0d
-#define PM8028_SUBTYPE		0x0e
-#define PM8901_SUBTYPE		0x0f
-#define PM8950_SUBTYPE		0x10
-#define PMI8950_SUBTYPE		0x11
-#define PM8998_SUBTYPE		0x14
-#define PMI8998_SUBTYPE		0x15
-#define PM8005_SUBTYPE		0x18
-#define PM660L_SUBTYPE		0x1A
-#define PM660_SUBTYPE		0x1B
-#define PM8150_SUBTYPE		0x1E
-#define PM8150L_SUBTYPE		0x1f
-#define PM8150B_SUBTYPE		0x20
-#define PMK8002_SUBTYPE		0x21
-#define PM8009_SUBTYPE		0x24
-#define PM8150C_SUBTYPE		0x26
-#define SMB2351_SUBTYPE		0x29
+struct qcom_spmi_dev {
+	int num_usids;
+	struct qcom_spmi_pmic pmic;
+};
+
+#define N_USIDS(n)		((void *)n)
 
  static const struct of_device_id pmic_spmi_id_table[] = {
-	{ .compatible = "qcom,pm660",     .data = (void *)PM660_SUBTYPE },
-	{ .compatible = "qcom,pm660l",    .data = (void *)PM660L_SUBTYPE },
-	{ .compatible = "qcom,pm8004",    .data = (void *)PM8004_SUBTYPE },
-	{ .compatible = "qcom,pm8005",    .data = (void *)PM8005_SUBTYPE },
-	{ .compatible = "qcom,pm8019",    .data = (void *)PM8019_SUBTYPE },
-	{ .compatible = "qcom,pm8028",    .data = (void *)PM8028_SUBTYPE },
-	{ .compatible = "qcom,pm8110",    .data = (void *)PM8110_SUBTYPE },
-	{ .compatible = "qcom,pm8150",    .data = (void *)PM8150_SUBTYPE },
-	{ .compatible = "qcom,pm8150b",   .data = (void *)PM8150B_SUBTYPE },
-	{ .compatible = "qcom,pm8150c",   .data = (void *)PM8150C_SUBTYPE },
-	{ .compatible = "qcom,pm8150l",   .data = (void *)PM8150L_SUBTYPE },
-	{ .compatible = "qcom,pm8226",    .data = (void *)PM8226_SUBTYPE },
-	{ .compatible = "qcom,pm8841",    .data = (void *)PM8841_SUBTYPE },
-	{ .compatible = "qcom,pm8901",    .data = (void *)PM8901_SUBTYPE },
-	{ .compatible = "qcom,pm8909",    .data = (void *)PM8909_SUBTYPE },
-	{ .compatible = "qcom,pm8916",    .data = (void *)PM8916_SUBTYPE },
-	{ .compatible = "qcom,pm8941",    .data = (void *)PM8941_SUBTYPE },
-	{ .compatible = "qcom,pm8950",    .data = (void *)PM8950_SUBTYPE },
-	{ .compatible = "qcom,pm8994",    .data = (void *)PM8994_SUBTYPE },
-	{ .compatible = "qcom,pm8998",    .data = (void *)PM8998_SUBTYPE },
-	{ .compatible = "qcom,pma8084",   .data = (void *)PMA8084_SUBTYPE },
-	{ .compatible = "qcom,pmd9635",   .data = (void *)PMD9635_SUBTYPE },
-	{ .compatible = "qcom,pmi8950",   .data = (void *)PMI8950_SUBTYPE },
-	{ .compatible = "qcom,pmi8962",   .data = (void *)PMI8962_SUBTYPE },
-	{ .compatible = "qcom,pmi8994",   .data = (void *)PMI8994_SUBTYPE },
-	{ .compatible = "qcom,pmi8998",   .data = (void *)PMI8998_SUBTYPE },
-	{ .compatible = "qcom,pmk8002",   .data = (void *)PMK8002_SUBTYPE },
-	{ .compatible = "qcom,smb2351",   .data = (void *)SMB2351_SUBTYPE },
-	{ .compatible = "qcom,spmi-pmic", .data = (void *)COMMON_SUBTYPE },
+	{ .compatible = "qcom,pm660", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm660l", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8004", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8005", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8019", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8028", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8110", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150b", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150c", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8150l", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8226", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8841", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8901", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8909", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8916", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8941", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8950", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8994", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pm8998", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pma8084", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmd9635", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmi8950", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmi8962", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmi8994", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmi8998", .data = N_USIDS(2) },
+	{ .compatible = "qcom,pmk8002", .data = N_USIDS(2) },
+	{ .compatible = "qcom,smb2351", .data = N_USIDS(2) },
+	{ .compatible = "qcom,spmi-pmic", .data = N_USIDS(1) },
  	{ }
  };
 
Quoted 4 lines

drivers/mfd/qcom-spmi-pmic.c line 65

Quoted 2 lines
drivers/mfd/qcom-spmi-pmic.c +1 -1
-static void pmic_spmi_show_revid(struct regmap *map, struct device *dev)
+#undef N_USIDS

Why is this here? Can't we use a unique macro instead?

This felt neat to do but yeah there's no reason to undefine the macro, I'll drop this.

Quoted 23 lines
Quoted 23 lines
drivers/mfd/qcom-spmi-pmic.c +17 -3
+/*
+ * A PMIC can be represented by multiple SPMI devices, but
+ * only the base PMIC device will contain a reference to
+ * the revision information.
+ *
+ * This function takes a pointer to a function device and
+ * returns a pointer to the base PMIC device.
+ *
+ * This only supports PMICs with 1 or 2 USIDs.
+ */
+static struct spmi_device *qcom_pmic_get_base_usid(struct device *dev)
  {
-	unsigned int rev2, minor, major, type, subtype;
-	const char *name = "unknown";
-	int ret, i;
+	struct spmi_device *sdev;
+	struct qcom_spmi_dev *ctx;
+	struct device_node *spmi_bus;
+	struct device_node *other_usid = NULL;
+	int function_parent_usid, ret;
+	u32 pmic_addr;
 
Quoted 7 lines

drivers/mfd/qcom-spmi-pmic.c line 87

Quoted 5 lines
drivers/mfd/qcom-spmi-pmic.c +2 -3
-	ret = regmap_read(map, PMIC_TYPE, &type);
-	if (ret < 0)
-		return;
+	if (!of_match_device(pmic_spmi_id_table, dev))
+		return ERR_PTR(-EINVAL);

Can this happen? How else would the device have been enumerated?

This function gets called from "qcom_pmic_get()" which can be called by any driver, the check is to make sure it's only called from drivers which are children of a qcom PMIC.

Quoted 7 lines

drivers/mfd/qcom-spmi-pmic.c line 90

Quoted 3 lines
drivers/mfd/qcom-spmi-pmic.c +2 -0
+	sdev = to_spmi_device(dev);
+	ctx = spmi_device_get_drvdata(sdev);

This function looks like abstraction for the sake of abstraction.

Why not just use dev_get_drvdata()?

That seems more sensible.

Quoted 37 lines
Quoted 4 lines
drivers/mfd/qcom-spmi-pmic.c +3 -0
+	/*
+	 * Quick return if the function device is already in the base
+	 * USID. This will always be hit for PMICs with only 1 USID.

drivers/mfd/qcom-spmi-pmic.c line 104

Quoted 10 lines
drivers/mfd/qcom-spmi-pmic.c +10 -0
+	 */
+	if (sdev->usid % ctx->num_usids == 0)
+		return sdev;
+
+	function_parent_usid = sdev->usid;
+
+	/*
+	 * Walk through the list of PMICs until we find the sibling USID.
+	 * The goal is to find the first USID which is less than the
+	 * number of USIDs in the PMIC away, e.g. for a PMIC with 2 USIDs

"array" perhaps?

drivers/mfd/qcom-spmi-pmic.c line 110

Quoted 6 lines
drivers/mfd/qcom-spmi-pmic.c +6 -0
+	 * where the function device is under USID 3, we want to find the
+	 * device for USID 2.
+	 */
+	spmi_bus = of_get_parent(sdev->dev.of_node);
+	do {
+		other_usid = of_get_next_child(spmi_bus, other_usid);

'\n'

drivers/mfd/qcom-spmi-pmic.c line 113

Quoted 3 lines
drivers/mfd/qcom-spmi-pmic.c +3 -0
+		ret = of_property_read_u32_index(other_usid, "reg", 0, &pmic_addr);
+		if (ret)
+			return ERR_PTR(ret);

'\n'

drivers/mfd/qcom-spmi-pmic.c line 115

Quoted 2 lines
drivers/mfd/qcom-spmi-pmic.c +2 -0
+		sdev = spmi_device_from_of(other_usid);
+		if (sdev == NULL) {

if (!sdev)

Quoted 9 lines

drivers/mfd/qcom-spmi-pmic.c line 122

Quoted 7 lines
drivers/mfd/qcom-spmi-pmic.c +7 -0
+			/*
+			 * If the base USID for this PMIC hasn't probed yet
+			 * but the secondary USID has, then we need to defer
+			 * the function driver so that it will attempt to
+			 * probe again when the base USID is ready.
+			 */
+			if (pmic_addr == function_parent_usid  - (ctx->num_usids - 1))

Double " ".

Ack

Quoted 2 lines

Over-bracketing of statements with matching operands.

I don't think x - (y - 1) is equal to x - y - 1? Or am I misunderstanding you here?

Quoted 10 lines

drivers/mfd/qcom-spmi-pmic.c line 129

Quoted 8 lines
drivers/mfd/qcom-spmi-pmic.c +7 -0
+				return ERR_PTR(-EPROBE_DEFER);
+
+			continue;
+		}
+
+		if (pmic_addr == function_parent_usid  - (ctx->num_usids - 1))
+			return sdev;

Wouldn't it be better written like this:

Yeah

Quoted 16 lines
Quoted 13 lines
drivers/mfd/qcom-spmi-pmic.c +12 -0
+		if (pmic_addr == function_parent_usid - (ctx->num_usids - 1)) {
+		        sdev = spmi_device_from_of(other_usid);
+		        if (!sdev)
+			        /*
+			         * If the base USID for this PMIC hasn't probed yet
+			         * but the secondary USID has, then we need to defer
+			         * the function driver so that it will attempt to
+			         * probe again when the base USID is ready.
+			         */
+				return ERR_PTR(-EPROBE_DEFER);
+                     return sdev;
+		}

[...]

Quoted 12 lines

drivers/mfd/qcom-spmi-pmic.c line 139

Quoted 10 lines
drivers/mfd/qcom-spmi-pmic.c +10 -0
+	} while (other_usid->sibling);
+
+	return ERR_PTR(-ENODATA);
+}
+
+static inline void pmic_print_info(struct device *dev, struct qcom_spmi_pmic *pmic)
+{
+	dev_dbg(dev, "%x: %s v%d.%d\n",
+		pmic->subtype, pmic->name, pmic->major, pmic->minor);
+}

More abstraction for no apparent reason.

Oops, this got a bit messy over several reworks, I'll stick the dev_dbg back in pmic_spmi_load_revid() and drop this function.

Quoted 107 lines
Quoted 50 lines
drivers/mfd/qcom-spmi-pmic.c +19 -16
-	if (type != PMIC_TYPE_VALUE)
-		return;
+static int pmic_spmi_load_revid(struct regmap *map, struct device *dev,
+				 struct qcom_spmi_pmic *pmic)
+{
+	int ret;
 
-	ret = regmap_read(map, PMIC_SUBTYPE, &subtype);
+	ret = regmap_read(map, PMIC_TYPE, &pmic->type);
  	if (ret < 0)
-		return;
+		return ret;
 
-	for (i = 0; i < ARRAY_SIZE(pmic_spmi_id_table); i++) {
-		if (subtype == (unsigned long)pmic_spmi_id_table[i].data)
-			break;
-	}
+	if (pmic->type != PMIC_TYPE_VALUE)
+		return ret;
 
-	if (i != ARRAY_SIZE(pmic_spmi_id_table))
-		name = pmic_spmi_id_table[i].compatible;
+	ret = regmap_read(map, PMIC_SUBTYPE, &pmic->subtype);
+	if (ret < 0)
+		return ret;
+
+	pmic->name = of_match_device(pmic_spmi_id_table, dev)->compatible;
 
-	ret = regmap_read(map, PMIC_REV2, &rev2);
+	ret = regmap_read(map, PMIC_REV2, &pmic->rev2);
  	if (ret < 0)
-		return;
+		return ret;
 
-	ret = regmap_read(map, PMIC_REV3, &minor);
+	ret = regmap_read(map, PMIC_REV3, &pmic->minor);
  	if (ret < 0)
-		return;
+		return ret;
 
-	ret = regmap_read(map, PMIC_REV4, &major);
+	ret = regmap_read(map, PMIC_REV4, &pmic->major);
  	if (ret < 0)
-		return;
+		return ret;
 
  	/*
  	 * In early versions of PM8941 and PM8226, the major revision number

drivers/mfd/qcom-spmi-pmic.c static void pmic_spmi_show_revid(struct regmap *map, struct device *dev) · line 178

Quoted 8 lines
drivers/mfd/qcom-spmi-pmic.c +2 -3
@@ -124,15 +174,34 @@ static void pmic_spmi_show_revid(struct regmap *map, struct device *dev)
  	 * Increment the major revision number here if the chip is an early
  	 * version of PM8941 or PM8226.
  	 */
-	if ((subtype == PM8941_SUBTYPE || subtype == PM8226_SUBTYPE) &&
-	    major < 0x02)
-		major++;
+	if ((pmic->subtype == PM8941_SUBTYPE || pmic->subtype == PM8226_SUBTYPE) &&
+	    pmic->major < 0x02)

Please define this magic number while you're at it.

Quoted 17 lines
drivers/mfd/qcom-spmi-pmic.c +14 -2
+		pmic->major++;
+
+	if (pmic->subtype == PM8110_SUBTYPE)
+		pmic->minor = pmic->rev2;
+
+	pmic_print_info(dev, pmic);
 
-	if (subtype == PM8110_SUBTYPE)
-		minor = rev2;
+	return 0;
+}
+
+/**
+ * qcom_pmic_get() - Get a pointer to the base PMIC device
+ *
+ * @dev: the pmic function device
+ * @return: the struct qcom_spmi_pmic* pointer associated with the function device

drivers/mfd/qcom-spmi-pmic.c static void pmic_spmi_show_revid(struct regmap *map, struct device *dev) · line 202

Quoted 10 lines
drivers/mfd/qcom-spmi-pmic.c +8 -1
+ */
+inline const struct qcom_spmi_pmic *qcom_pmic_get(struct device *dev)
+{
+	struct spmi_device *sdev = qcom_pmic_get_base_usid(dev->parent);
 
-	dev_dbg(dev, "%x: %s v%d.%d\n", subtype, name, major, minor);
+	if (IS_ERR(sdev))
+		return ERR_CAST(sdev);
+
+	return &((struct qcom_spmi_dev *)spmi_device_get_drvdata(sdev))->pmic;

This is horrible. Please expand it out.

Quoted 16 lines
drivers/mfd/qcom-spmi-pmic.c +3 -0
  }
+EXPORT_SYMBOL(qcom_pmic_get);
 
  static const struct regmap_config spmi_regmap_config = {
  	.reg_bits	= 16,
@@ -144,14 +213,26 @@ static const struct regmap_config spmi_regmap_config = {
  static int pmic_spmi_probe(struct spmi_device *sdev)
  {
  	struct regmap *regmap;
+	struct qcom_spmi_dev *ctx;
+	int ret;
 
  	regmap = devm_regmap_init_spmi_ext(sdev, &spmi_regmap_config);
  	if (IS_ERR(regmap))
  		return PTR_ERR(regmap);
 
Quoted 7 lines

drivers/mfd/qcom-spmi-pmic.c static const struct regmap_config spmi_regmap_config = { · line 227

Quoted 5 lines
drivers/mfd/qcom-spmi-pmic.c +5 -0
+	ctx = devm_kzalloc(&sdev->dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	ctx->num_usids = (long)of_device_get_match_data(&sdev->dev);

Why does this need to be long?

The compiler complains with
../drivers/mfd/qcom-spmi-pmic.c: In function 'pmic_spmi_probe':
../drivers/mfd/qcom-spmi-pmic.c:236:26: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]

  236 |         ctx->num_usids = (int)of_device_get_match_data(&sdev->dev);
      |

Due to match data being void*. I wasn't able to find a better solution than casting this way, do you have any suggestions?

I just found uintptr_t, maybe that might be more explicit?

Quoted 18 lines

In fact, it's not is it? It's an int:

    +struct qcom_spmi_dev {
    +	int num_usids;
    +	struct qcom_spmi_pmic pmic;
    +};
Quoted 10 lines
drivers/mfd/qcom-spmi-pmic.c +6 -2
  	/* Only the first slave id for a PMIC contains this information */
-	if (sdev->usid % 2 == 0)
-		pmic_spmi_show_revid(regmap, &sdev->dev);
+	if (sdev->usid % ctx->num_usids == 0) {
+		ret = pmic_spmi_load_revid(regmap, &sdev->dev, &ctx->pmic);
+		if (ret < 0)
+			return ret;
+	}
+	spmi_device_set_drvdata(sdev, ctx);
 
Quoted 13 lines

include/soc/qcom/qcom-spmi-pmic.h line 3

Quoted 11 lines
drivers/mfd/qcom-spmi-pmic.c +0 -0
  	return devm_of_platform_populate(&sdev->dev);
  }
include/soc/qcom/qcom-spmi-pmic.h new file +3 -0
new file mode 100644
index 000000000000..5400e6509fe8
@@ -0,0 +1,60 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Copyright (c) 2021 Linaro. All rights reserved.
+ * Copyright (c) 2021 Caleb Connolly <[email protected]>

Your very own Copyright? Why?

I did some research originally and couldn't find any docs on Linaro precedent here, so went with this originally... I switched over the other files when I realised that "Author:" was the preferred approach but I guess this one slipped through the crack.

Quoted 63 lines

Any not Author: instead?

Quoted 43 lines
include/soc/qcom/qcom-spmi-pmic.h new file +43 -0
+ */
+
+#ifndef __QCOM_SPMI_PMIC_H__
+#define __QCOM_SPMI_PMIC_H__
+
+#define COMMON_SUBTYPE		0x00
+#define PM8941_SUBTYPE		0x01
+#define PM8841_SUBTYPE		0x02
+#define PM8019_SUBTYPE		0x03
+#define PM8226_SUBTYPE		0x04
+#define PM8110_SUBTYPE		0x05
+#define PMA8084_SUBTYPE		0x06
+#define PMI8962_SUBTYPE		0x07
+#define PMD9635_SUBTYPE		0x08
+#define PM8994_SUBTYPE		0x09
+#define PMI8994_SUBTYPE		0x0a
+#define PM8916_SUBTYPE		0x0b
+#define PM8004_SUBTYPE		0x0c
+#define PM8909_SUBTYPE		0x0d
+#define PM8028_SUBTYPE		0x0e
+#define PM8901_SUBTYPE		0x0f
+#define PM8950_SUBTYPE		0x10
+#define PMI8950_SUBTYPE		0x11
+#define PM8998_SUBTYPE		0x14
+#define PMI8998_SUBTYPE		0x15
+#define PM8005_SUBTYPE		0x18
+#define PM660L_SUBTYPE		0x1A
+#define PM660_SUBTYPE		0x1B
+#define PM8150_SUBTYPE		0x1E
+#define PM8150L_SUBTYPE		0x1f
+#define PM8150B_SUBTYPE		0x20
+#define PMK8002_SUBTYPE		0x21
+#define PM8009_SUBTYPE		0x24
+#define PM8150C_SUBTYPE		0x26
+#define SMB2351_SUBTYPE		0x29
+
+#define PMI8998_FAB_ID_SMIC	0x11
+#define PMI8998_FAB_ID_GF	0x30
+
+#define PM660_FAB_ID_GF		0x0
+#define PM660_FAB_ID_TSMC	0x2
+#define PM660_FAB_ID_MX		0x3
+

include/soc/qcom/qcom-spmi-pmic.h line 56

Quoted 10 lines
include/soc/qcom/qcom-spmi-pmic.h new file +10 -0
+struct qcom_spmi_pmic {
+	unsigned int type;
+	unsigned int subtype;
+	unsigned int major;
+	unsigned int minor;
+	unsigned int rev2;
+	const char *name;
+};
+
+struct device;

Can't you just include the correct header?Sure

Quoted 3 lines
include/soc/qcom/qcom-spmi-pmic.h new file +3 -0
+inline const struct qcom_spmi_pmic *qcom_pmic_get(struct device *dev);
+
+#endif /* __QCOM_SPMI_PMIC_H__ */
Signature · 2 lines
Kind Regards,
Caleb (they/he)
#5 lore raw

Re: [PATCH v13 2/9] mfd: qcom-spmi-pmic: expose the PMIC revid information to clients

Quoted 22 lines · Caleb Connolly
Quoted 21 lines · Lee Jones
Quoted 19 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

Some PMIC functions such as the RRADC need to be aware of the PMIC chip revision information to implement errata or otherwise adjust behaviour, export the PMIC information to enable this.

This is specifically required to enable the RRADC to adjust coefficients based on which chip fab the PMIC was produced in, this can vary per unique device and therefore has to be read at runtime.

---
  drivers/mfd/qcom-spmi-pmic.c      | 261 +++++++++++++++++++-----------
  include/soc/qcom/qcom-spmi-pmic.h |  60 +++++++
  2 files changed, 231 insertions(+), 90 deletions(-)

create mode 100644 include/soc/qcom/qcom-spmi-pmic.h

[...]

Quoted 9 lines
Quoted 9 lines

drivers/mfd/qcom-spmi-pmic.c line 122

Quoted 7 lines
drivers/mfd/qcom-spmi-pmic.c +7 -0
+			/*
+			 * If the base USID for this PMIC hasn't probed yet
+			 * but the secondary USID has, then we need to defer
+			 * the function driver so that it will attempt to
+			 * probe again when the base USID is ready.
+			 */
+			if (pmic_addr == function_parent_usid  - (ctx->num_usids - 1))

Double " ".

Quoted 4 lines

Ack

Quoted 2 lines

Over-bracketing of statements with matching operands.

I don't think x - (y - 1) is equal to x - y - 1? Or am I misunderstanding you here?

Can you give me an example when this would be the case?

Signature · 4 lines
Lee Jones [李琼斯]
Principal Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
#6 lore raw

Re: [PATCH v13 2/9] mfd: qcom-spmi-pmic: expose the PMIC revid information to clients

Quoted 35 lines · Lee Jones
Quoted 22 lines · Caleb Connolly
Quoted 21 lines · Lee Jones
Quoted 19 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

Some PMIC functions such as the RRADC need to be aware of the PMIC chip revision information to implement errata or otherwise adjust behaviour, export the PMIC information to enable this.

This is specifically required to enable the RRADC to adjust coefficients based on which chip fab the PMIC was produced in, this can vary per unique device and therefore has to be read at runtime.

---
   drivers/mfd/qcom-spmi-pmic.c      | 261 +++++++++++++++++++-----------
   include/soc/qcom/qcom-spmi-pmic.h |  60 +++++++
   2 files changed, 231 insertions(+), 90 deletions(-)

create mode 100644 include/soc/qcom/qcom-spmi-pmic.h

[...]

Quoted 9 lines
Quoted 9 lines

drivers/mfd/qcom-spmi-pmic.c line 122

Quoted 7 lines
drivers/mfd/qcom-spmi-pmic.c +7 -0
+			/*
+			 * If the base USID for this PMIC hasn't probed yet
+			 * but the secondary USID has, then we need to defer
+			 * the function driver so that it will attempt to
+			 * probe again when the base USID is ready.
+			 */
+			if (pmic_addr == function_parent_usid  - (ctx->num_usids - 1))

Double " ".

Quoted 6 lines
Quoted 4 lines

Ack

Quoted 2 lines

Over-bracketing of statements with matching operands.

I don't think x - (y - 1) is equal to x - y - 1? Or am I misunderstanding you here?

Can you give me an example when this would be the case?

According to the Python interpreter:

Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

x=7
y=4
x - y - 1

2

Quoted 1 line
Quoted 1 line
Quoted 1 line

x - (y - 1)

4

C does also respect the first rule of BODMAS - parenthesis are always evaluated first.

Quoted 1 line
Signature · 2 lines
Kind Regards,
Caleb (they/he)
#7 lore raw

Re: [PATCH v13 2/9] mfd: qcom-spmi-pmic: expose the PMIC revid information to clients

Quoted 46 lines · Caleb Connolly
Quoted 35 lines · Lee Jones
Quoted 22 lines · Caleb Connolly
Quoted 21 lines · Lee Jones
Quoted 19 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

Some PMIC functions such as the RRADC need to be aware of the PMIC chip revision information to implement errata or otherwise adjust behaviour, export the PMIC information to enable this.

This is specifically required to enable the RRADC to adjust coefficients based on which chip fab the PMIC was produced in, this can vary per unique device and therefore has to be read at runtime.

---
   drivers/mfd/qcom-spmi-pmic.c      | 261 +++++++++++++++++++-----------
   include/soc/qcom/qcom-spmi-pmic.h |  60 +++++++
   2 files changed, 231 insertions(+), 90 deletions(-)

create mode 100644 include/soc/qcom/qcom-spmi-pmic.h

[...]

Quoted 9 lines
Quoted 9 lines

drivers/mfd/qcom-spmi-pmic.c line 122

Quoted 7 lines
drivers/mfd/qcom-spmi-pmic.c +7 -0
+			/*
+			 * If the base USID for this PMIC hasn't probed yet
+			 * but the secondary USID has, then we need to defer
+			 * the function driver so that it will attempt to
+			 * probe again when the base USID is ready.
+			 */
+			if (pmic_addr == function_parent_usid  - (ctx->num_usids - 1))

Double " ".

Quoted 6 lines
Quoted 4 lines

Ack

Quoted 2 lines

Over-bracketing of statements with matching operands.

I don't think x - (y - 1) is equal to x - y - 1? Or am I misunderstanding you here?

Can you give me an example when this would be the case?

According to the Python interpreter:

Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

x=7
y=4
x - y - 1

Quoted 6 lines

2

Quoted 1 line
Quoted 1 line
Quoted 1 line

x - (y - 1)

4

C does also respect the first rule of BODMAS - parenthesis are always evaluated first.

Fair point, well presented.

Thanks for this - I understand the problem now.

Signature · 4 lines
Lee Jones [李琼斯]
Principal Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
#8 lore raw

Re: [PATCH v13 2/9] mfd: qcom-spmi-pmic: expose the PMIC revid information to clients

Quoted 49 lines · Lee Jones
Quoted 48 lines · Caleb Connolly
Quoted 35 lines · Lee Jones
Quoted 22 lines · Caleb Connolly
Quoted 21 lines · Lee Jones
Quoted 19 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

Some PMIC functions such as the RRADC need to be aware of the PMIC chip revision information to implement errata or otherwise adjust behaviour, export the PMIC information to enable this.

This is specifically required to enable the RRADC to adjust coefficients based on which chip fab the PMIC was produced in, this can vary per unique device and therefore has to be read at runtime.

---
    drivers/mfd/qcom-spmi-pmic.c      | 261 +++++++++++++++++++-----------
    include/soc/qcom/qcom-spmi-pmic.h |  60 +++++++
    2 files changed, 231 insertions(+), 90 deletions(-)

create mode 100644 include/soc/qcom/qcom-spmi-pmic.h

[...]

Quoted 9 lines
Quoted 9 lines

drivers/mfd/qcom-spmi-pmic.c line 122

Quoted 7 lines
drivers/mfd/qcom-spmi-pmic.c +7 -0
+			/*
+			 * If the base USID for this PMIC hasn't probed yet
+			 * but the secondary USID has, then we need to defer
+			 * the function driver so that it will attempt to
+			 * probe again when the base USID is ready.
+			 */
+			if (pmic_addr == function_parent_usid  - (ctx->num_usids - 1))

Double " ".

Quoted 6 lines
Quoted 4 lines

Ack

Quoted 2 lines

Over-bracketing of statements with matching operands.

I don't think x - (y - 1) is equal to x - y - 1? Or am I misunderstanding you here?

Can you give me an example when this would be the case?

According to the Python interpreter:

Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

x=7
y=4
x - y - 1

2

Quoted 1 line
Quoted 1 line
Quoted 1 line

x - (y - 1)

Quoted 8 lines
Quoted 4 lines

4

C does also respect the first rule of BODMAS - parenthesis are always evaluated first.

Fair point, well presented.

Thanks for this - I understand the problem now.

Thanks,

Could you respond to my other two points in https://lore.kernel.org/linux-arm-msm/[email protected]/

Regarding

if (!of_match_device(pmic_spmi_id_table, dev))

and

ctx->num_usids = (long)of_device_get_match_data(&sdev->dev);

Quoted 1 line
Signature · 2 lines
Kind Regards,
Caleb (they/he)
#9 lore raw

PATCH v13 3/9 mfd: qcom-spmi-pmic: read fab id on supported PMICs

In reply to Caleb Connolly

From: Caleb Connolly <[email protected]>

The PMI8998 and PM660 expose the fab_id, this is needed by drivers like the RRADC to calibrate ADC values.

---
 drivers/mfd/qcom-spmi-pmic.c      | 7 +++++++
 include/soc/qcom/qcom-spmi-pmic.h | 1 +
 2 files changed, 8 insertions(+)
drivers/mfd/qcom-spmi-pmic.c +7 -0
index d8e54d9d3448..43e0c55696c7 100644
@@ -19,6 +19,7 @@
 #define PMIC_REV4		0x103
 #define PMIC_TYPE		0x104
 #define PMIC_SUBTYPE		0x105
+#define PMIC_FAB_ID		0x1f2
 
 #define PMIC_TYPE_VALUE		0x51
 
@@ -168,6 +169,12 @@ static int pmic_spmi_load_revid(struct regmap *map, struct device *dev,
 	if (ret < 0)
 		return ret;
 
+	if (pmic->subtype == PMI8998_SUBTYPE || pmic->subtype == PM660_SUBTYPE) {
+		ret = regmap_read(map, PMIC_FAB_ID, &pmic->fab_id);
+		if (ret < 0)
+			return ret;
+	}
+
 	/*
 	 * In early versions of PM8941 and PM8226, the major revision number
 	 * started incrementing from 0 (eg 0 = v1.0, 1 = v2.0).
include/soc/qcom/qcom-spmi-pmic.h +1 -0
index 5400e6509fe8..ff839b230e62 100644
@@ -50,6 +50,7 @@ struct qcom_spmi_pmic {
 	unsigned int major;
 	unsigned int minor;
 	unsigned int rev2;
+	unsigned int fab_id;
 	const char *name;
 };
 
Signature · 1 line
2.35.1
Acked-by on v13 3/9
#10 lore raw

Re: [PATCH v13 3/9] mfd: qcom-spmi-pmic: read fab id on supported PMICs

Quoted 5 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

The PMI8998 and PM660 expose the fab_id, this is needed by drivers like the RRADC to calibrate ADC values.

Quoted 7 lines
---
 drivers/mfd/qcom-spmi-pmic.c      | 7 +++++++
 include/soc/qcom/qcom-spmi-pmic.h | 1 +
 2 files changed, 8 insertions(+)

Please change the Subject line to match the style of the sub-system?

Once changed:

Signature · 4 lines
Lee Jones [李琼斯]
Principal Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
#11 lore raw

Re: [PATCH v13 3/9] mfd: qcom-spmi-pmic: read fab id on supported PMICs

Quoted 15 lines · Lee Jones
Quoted 5 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

The PMI8998 and PM660 expose the fab_id, this is needed by drivers like the RRADC to calibrate ADC values.

Quoted 7 lines
---
  drivers/mfd/qcom-spmi-pmic.c      | 7 +++++++
  include/soc/qcom/qcom-spmi-pmic.h | 1 +
  2 files changed, 8 insertions(+)
Quoted 1 line

Please change the Subject line to match the style of the sub-system?

Hi, sorry if this is a silly question, I don't quite understand what you want me to change here, the subject line is in the same "mfd: driver:" format as other patches in the subsystem?

Quoted 5 lines

Once changed:

Signature · 2 lines
Kind Regards,
Caleb (they/he)
#12 lore raw

Re: [PATCH v13 3/9] mfd: qcom-spmi-pmic: read fab id on supported PMICs

Quoted 16 lines · Caleb Connolly
Quoted 15 lines · Lee Jones
Quoted 12 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

The PMI8998 and PM660 expose the fab_id, this is needed by drivers like the RRADC to calibrate ADC values.

---
  drivers/mfd/qcom-spmi-pmic.c      | 7 +++++++
  include/soc/qcom/qcom-spmi-pmic.h | 1 +
  2 files changed, 8 insertions(+)
Quoted 4 lines
Quoted 1 line

Please change the Subject line to match the style of the sub-system?

Hi, sorry if this is a silly question, I don't quite understand what you want me to change here, the subject line is in the same "mfd: driver:" format as other patches in the subsystem?

mfd: qcom-spmi-pmic: Read fab ID on supported PMICs

What's 'fab' should that be capitalised too?

Quoted 5 lines
Quoted 4 lines

Once changed:

Signature · 4 lines
Lee Jones [李琼斯]
Principal Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
#13 lore raw

Re: [PATCH v13 3/9] mfd: qcom-spmi-pmic: read fab id on supported PMICs

Quoted 17 lines · Lee Jones
Quoted 16 lines · Caleb Connolly
Quoted 15 lines · Lee Jones
Quoted 12 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

The PMI8998 and PM660 expose the fab_id, this is needed by drivers like the RRADC to calibrate ADC values.

---
   drivers/mfd/qcom-spmi-pmic.c      | 7 +++++++
   include/soc/qcom/qcom-spmi-pmic.h | 1 +
   2 files changed, 8 insertions(+)
Quoted 8 lines
Quoted 4 lines
Quoted 1 line

Please change the Subject line to match the style of the sub-system?

Hi, sorry if this is a silly question, I don't quite understand what you want me to change here, the subject line is in the same "mfd: driver:" format as other patches in the subsystem?

mfd: qcom-spmi-pmic: Read fab ID on supported PMICs

What's 'fab' should that be capitalised too?

"fab" is short for fabrication I think, the register value can be used to determine which factory the chip was manufactured in.

I can make it clearer and go for

mfd: qcom-spmi-pmic: Read fabrication ID on supported PMICs

Quoted 7 lines
Quoted 6 lines
Quoted 5 lines

Once changed:

Signature · 2 lines
Kind Regards,
Caleb (they/he)
#14 lore raw

Re: [PATCH v13 3/9] mfd: qcom-spmi-pmic: read fab id on supported PMICs

Quoted 27 lines · Caleb Connolly
Quoted 24 lines · Lee Jones
Quoted 16 lines · Caleb Connolly
Quoted 15 lines · Lee Jones
Quoted 12 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

The PMI8998 and PM660 expose the fab_id, this is needed by drivers like the RRADC to calibrate ADC values.

---
   drivers/mfd/qcom-spmi-pmic.c      | 7 +++++++
   include/soc/qcom/qcom-spmi-pmic.h | 1 +
   2 files changed, 8 insertions(+)
Quoted 4 lines
Quoted 1 line

Please change the Subject line to match the style of the sub-system?

Hi, sorry if this is a silly question, I don't quite understand what you want me to change here, the subject line is in the same "mfd: driver:" format as other patches in the subsystem?

mfd: qcom-spmi-pmic: Read fab ID on supported PMICs

Quoted 7 lines
Quoted 1 line

What's 'fab' should that be capitalised too?

"fab" is short for fabrication I think, the register value can be used to determine which factory the chip was manufactured in.

I can make it clearer and go for

mfd: qcom-spmi-pmic: Read fabrication ID on supported PMICs

Clearer, thanks.

Signature · 4 lines
Lee Jones [李琼斯]
Principal Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
#15 lore raw

PATCH v13 4/9 dt-bindings: iio: adc: document qcom-spmi-rradc

In reply to Caleb Connolly

From: Caleb Connolly <[email protected]>

Add dt-binding docs for the Qualcomm SPMI RRADC found in PMICs like PMI8998 and PMI8994

---
 .../bindings/iio/adc/qcom,spmi-rradc.yaml     | 51 +++++++++++++++++++
 1 file changed, 51 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-rradc.yaml
Documentation/devicetree/bindings/iio/adc/qcom,spmi-rradc.yaml new file +51 -0
new file mode 100644
index 000000000000..c8cbfd3444be
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/qcom,spmi-rradc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm's SPMI PMIC Round Robin ADC
+
+maintainers:
+  - Caleb Connolly <[email protected]>
+
+description: |
+  The Qualcomm SPMI Round Robin ADC (RRADC) provides interface to clients to
+  read the voltage, current and temperature for supported peripherals such as
+  the battery thermistor die temperature, charger temperature, USB and DC input
+  voltage / current and battery ID resistor.
+
+properties:
+  compatible:
+    enum:
+      - qcom,pmi8998-rradc
+      - qcom,pm660-rradc
+
+  reg:
+    maxItems: 1
+
+  qcom,batt-id-delay-ms:
+    description: Sets the hardware settling time for the battery ID resistor.
+    enum: [0, 1, 4, 12, 20, 40, 60, 80]
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    pmic {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      pmic_rradc: adc@4500 {
+          compatible = "qcom,pmi8998-rradc";
+          reg = <0x4500>;
+          #io-channel-cells  = <1>;
+      };
+    };
Signature · 1 line
2.35.1
Reviewed-by on v13 4/9
#16 lore raw

Re: [PATCH v13 4/9] dt-bindings: iio: adc: document qcom-spmi-rradc

Quoted 11 lines · Caleb Connolly

From: Caleb Connolly <[email protected]>

Add dt-binding docs for the Qualcomm SPMI RRADC found in PMICs like PMI8998 and PMI8994

---
 .../bindings/iio/adc/qcom,spmi-rradc.yaml     | 51 +++++++++++++++++++
 1 file changed, 51 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-rradc.yaml

Best regards,
Krzysztof

maintainer Reviewed-by on v13 4/9
#17 lore raw

Re: [PATCH v13 4/9] dt-bindings: iio: adc: document qcom-spmi-rradc

In reply to Caleb Connolly
Quoted 6 lines · On Wed, 23 Mar 2022 16:28:15 +0000 Caleb Connolly <[email protected]>…

From: Caleb Connolly <[email protected]>

Add dt-binding docs for the Qualcomm SPMI RRADC found in PMICs like PMI8998 and PMI8994

On basis I don't mind if Lee want's to pick this up and send me an immutable branch. If not, once Lee has taken a look I can create an immutable branch for this.

Quoted 62 lines
---
 .../bindings/iio/adc/qcom,spmi-rradc.yaml     | 51 +++++++++++++++++++
 1 file changed, 51 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-rradc.yaml
Documentation/devicetree/bindings/iio/adc/qcom,spmi-rradc.yaml new file +51 -0
new file mode 100644
index 000000000000..c8cbfd3444be
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/qcom,spmi-rradc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm's SPMI PMIC Round Robin ADC
+
+maintainers:
+  - Caleb Connolly <[email protected]>
+
+description: |
+  The Qualcomm SPMI Round Robin ADC (RRADC) provides interface to clients to
+  read the voltage, current and temperature for supported peripherals such as
+  the battery thermistor die temperature, charger temperature, USB and DC input
+  voltage / current and battery ID resistor.
+
+properties:
+  compatible:
+    enum:
+      - qcom,pmi8998-rradc
+      - qcom,pm660-rradc
+
+  reg:
+    maxItems: 1
+
+  qcom,batt-id-delay-ms:
+    description: Sets the hardware settling time for the battery ID resistor.
+    enum: [0, 1, 4, 12, 20, 40, 60, 80]
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    pmic {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      pmic_rradc: adc@4500 {
+          compatible = "qcom,pmi8998-rradc";
+          reg = <0x4500>;
+          #io-channel-cells  = <1>;
+      };
+    };
#18 lore raw

PATCH v13 5/9 iio: adc: qcom-spmi-rradc: introduce round robin adc

In reply to Caleb Connolly

From: Caleb Connolly <[email protected]>

The Round Robin ADC is responsible for reading data about the rate of charge from the USB or DC input ports, it can also read the battery ID (resistence), skin temperature and the die temperature of the pmic. It is found on the PMI8998 and PM660 Qualcomm PMICs.

---
 drivers/iio/adc/Kconfig           |   12 +
 drivers/iio/adc/Makefile          |    1 +
 drivers/iio/adc/qcom-spmi-rradc.c | 1021 +++++++++++++++++++++++++++++
 3 files changed, 1034 insertions(+)
 create mode 100644 drivers/iio/adc/qcom-spmi-rradc.c
drivers/iio/adc/Kconfig +12 -0
index 4fdc8bfbb407..66557b434fa8 100644
@@ -812,6 +812,18 @@ config QCOM_PM8XXX_XOADC
 	  To compile this driver as a module, choose M here: the module
 	  will be called qcom-pm8xxx-xoadc.
 
+config QCOM_SPMI_RRADC
+	tristate "Qualcomm SPMI RRADC"
+	depends on MFD_SPMI_PMIC
+	help
+	  This is for the PMIC Round Robin ADC driver.
+
+	  This driver exposes the battery ID resistor, battery thermal, PMIC die
+	  temperature, charger USB in and DC in voltage and current.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called qcom-qpmi-rradc.
+
 config QCOM_SPMI_IADC
 	tristate "Qualcomm SPMI PMIC current ADC"
 	depends on SPMI
drivers/iio/adc/Makefile +1 -0
index 4a8f1833993b..b0dd7f142abd 100644
@@ -77,6 +77,7 @@ obj-$(CONFIG_NPCM_ADC) += npcm_adc.o
 obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
 obj-$(CONFIG_QCOM_SPMI_ADC5) += qcom-spmi-adc5.o
 obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
+obj-$(CONFIG_QCOM_SPMI_RRADC) += qcom-spmi-rradc.o
 obj-$(CONFIG_QCOM_VADC_COMMON) += qcom-vadc-common.o
 obj-$(CONFIG_QCOM_SPMI_VADC) += qcom-spmi-vadc.o
 obj-$(CONFIG_QCOM_PM8XXX_XOADC) += qcom-pm8xxx-xoadc.o
drivers/iio/adc/qcom-spmi-rradc.c new file +1021 -0

1,021 lines not on this page · raw message

Signature · 1 line
2.35.1
maintainer Reviewed-by on v13 5/9
#19 lore raw

Re: [PATCH v13 5/9] iio: adc: qcom-spmi-rradc: introduce round robin adc

Quoted 8 lines · On Wed, 23 Mar 2022 16:28:16 +0000 Caleb Connolly <[email protected]>…

From: Caleb Connolly <[email protected]>

The Round Robin ADC is responsible for reading data about the rate of charge from the USB or DC input ports, it can also read the battery ID (resistence), skin temperature and the die temperature of the pmic. It is found on the PMI8998 and PM660 Qualcomm PMICs.

Whilst I said this patch was fine a few versions ago I didn't add a tag on basis I would probably end up picking it up.

To make things more flexible, I'll add one and either Lee or I can do the immutable branch once Lee has had a chance to take a look and is happy with the mfd parts.

Quoted 1,069 lines
---
 drivers/iio/adc/Kconfig           |   12 +
 drivers/iio/adc/Makefile          |    1 +
 drivers/iio/adc/qcom-spmi-rradc.c | 1021 +++++++++++++++++++++++++++++
 3 files changed, 1034 insertions(+)
 create mode 100644 drivers/iio/adc/qcom-spmi-rradc.c
drivers/iio/adc/Kconfig +12 -0
index 4fdc8bfbb407..66557b434fa8 100644
@@ -812,6 +812,18 @@ config QCOM_PM8XXX_XOADC
 	  To compile this driver as a module, choose M here: the module
 	  will be called qcom-pm8xxx-xoadc.
 
+config QCOM_SPMI_RRADC
+	tristate "Qualcomm SPMI RRADC"
+	depends on MFD_SPMI_PMIC
+	help
+	  This is for the PMIC Round Robin ADC driver.
+
+	  This driver exposes the battery ID resistor, battery thermal, PMIC die
+	  temperature, charger USB in and DC in voltage and current.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called qcom-qpmi-rradc.
+
 config QCOM_SPMI_IADC
 	tristate "Qualcomm SPMI PMIC current ADC"
 	depends on SPMI
drivers/iio/adc/Makefile +1 -0
index 4a8f1833993b..b0dd7f142abd 100644
@@ -77,6 +77,7 @@ obj-$(CONFIG_NPCM_ADC) += npcm_adc.o
 obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
 obj-$(CONFIG_QCOM_SPMI_ADC5) += qcom-spmi-adc5.o
 obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
+obj-$(CONFIG_QCOM_SPMI_RRADC) += qcom-spmi-rradc.o
 obj-$(CONFIG_QCOM_VADC_COMMON) += qcom-vadc-common.o
 obj-$(CONFIG_QCOM_SPMI_VADC) += qcom-spmi-vadc.o
 obj-$(CONFIG_QCOM_PM8XXX_XOADC) += qcom-pm8xxx-xoadc.o
drivers/iio/adc/qcom-spmi-rradc.c new file +1021 -0
new file mode 100644
index 000000000000..230477fc45d2
@@ -0,0 +1,1021 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2016-2017, 2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022 Linaro Limited.
+ *  Author: Caleb Connolly <[email protected]>
+ *
+ * This driver is for the Round Robin ADC found in the pmi8998 and pm660 PMICs.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/spmi.h>
+#include <linux/types.h>
+#include <linux/units.h>
+
+#include <asm/unaligned.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/types.h>
+
+#include <soc/qcom/qcom-spmi-pmic.h>
+
+#define DRIVER_NAME "qcom-spmi-rradc"
+
+#define RR_ADC_EN_CTL 0x46
+#define RR_ADC_SKIN_TEMP_LSB 0x50
+#define RR_ADC_SKIN_TEMP_MSB 0x51
+#define RR_ADC_CTL 0x52
+#define RR_ADC_CTL_CONTINUOUS_SEL BIT(3)
+#define RR_ADC_LOG 0x53
+#define RR_ADC_LOG_CLR_CTRL BIT(0)
+
+#define RR_ADC_FAKE_BATT_LOW_LSB 0x58
+#define RR_ADC_FAKE_BATT_LOW_MSB 0x59
+#define RR_ADC_FAKE_BATT_HIGH_LSB 0x5A
+#define RR_ADC_FAKE_BATT_HIGH_MSB 0x5B
+
+#define RR_ADC_BATT_ID_CTRL 0x60
+#define RR_ADC_BATT_ID_CTRL_CHANNEL_CONV BIT(0)
+#define RR_ADC_BATT_ID_TRIGGER 0x61
+#define RR_ADC_BATT_ID_STS 0x62
+#define RR_ADC_BATT_ID_CFG 0x63
+#define BATT_ID_SETTLE_MASK GENMASK(7, 5)
+#define RR_ADC_BATT_ID_5_LSB 0x66
+#define RR_ADC_BATT_ID_5_MSB 0x67
+#define RR_ADC_BATT_ID_15_LSB 0x68
+#define RR_ADC_BATT_ID_15_MSB 0x69
+#define RR_ADC_BATT_ID_150_LSB 0x6A
+#define RR_ADC_BATT_ID_150_MSB 0x6B
+
+#define RR_ADC_BATT_THERM_CTRL 0x70
+#define RR_ADC_BATT_THERM_TRIGGER 0x71
+#define RR_ADC_BATT_THERM_STS 0x72
+#define RR_ADC_BATT_THERM_CFG 0x73
+#define RR_ADC_BATT_THERM_LSB 0x74
+#define RR_ADC_BATT_THERM_MSB 0x75
+#define RR_ADC_BATT_THERM_FREQ 0x76
+
+#define RR_ADC_AUX_THERM_CTRL 0x80
+#define RR_ADC_AUX_THERM_TRIGGER 0x81
+#define RR_ADC_AUX_THERM_STS 0x82
+#define RR_ADC_AUX_THERM_CFG 0x83
+#define RR_ADC_AUX_THERM_LSB 0x84
+#define RR_ADC_AUX_THERM_MSB 0x85
+
+#define RR_ADC_SKIN_HOT 0x86
+#define RR_ADC_SKIN_TOO_HOT 0x87
+
+#define RR_ADC_AUX_THERM_C1 0x88
+#define RR_ADC_AUX_THERM_C2 0x89
+#define RR_ADC_AUX_THERM_C3 0x8A
+#define RR_ADC_AUX_THERM_HALF_RANGE 0x8B
+
+#define RR_ADC_USB_IN_V_CTRL 0x90
+#define RR_ADC_USB_IN_V_TRIGGER 0x91
+#define RR_ADC_USB_IN_V_STS 0x92
+#define RR_ADC_USB_IN_V_LSB 0x94
+#define RR_ADC_USB_IN_V_MSB 0x95
+#define RR_ADC_USB_IN_I_CTRL 0x98
+#define RR_ADC_USB_IN_I_TRIGGER 0x99
+#define RR_ADC_USB_IN_I_STS 0x9A
+#define RR_ADC_USB_IN_I_LSB 0x9C
+#define RR_ADC_USB_IN_I_MSB 0x9D
+
+#define RR_ADC_DC_IN_V_CTRL 0xA0
+#define RR_ADC_DC_IN_V_TRIGGER 0xA1
+#define RR_ADC_DC_IN_V_STS 0xA2
+#define RR_ADC_DC_IN_V_LSB 0xA4
+#define RR_ADC_DC_IN_V_MSB 0xA5
+#define RR_ADC_DC_IN_I_CTRL 0xA8
+#define RR_ADC_DC_IN_I_TRIGGER 0xA9
+#define RR_ADC_DC_IN_I_STS 0xAA
+#define RR_ADC_DC_IN_I_LSB 0xAC
+#define RR_ADC_DC_IN_I_MSB 0xAD
+
+#define RR_ADC_PMI_DIE_TEMP_CTRL 0xB0
+#define RR_ADC_PMI_DIE_TEMP_TRIGGER 0xB1
+#define RR_ADC_PMI_DIE_TEMP_STS 0xB2
+#define RR_ADC_PMI_DIE_TEMP_CFG 0xB3
+#define RR_ADC_PMI_DIE_TEMP_LSB 0xB4
+#define RR_ADC_PMI_DIE_TEMP_MSB 0xB5
+
+#define RR_ADC_CHARGER_TEMP_CTRL 0xB8
+#define RR_ADC_CHARGER_TEMP_TRIGGER 0xB9
+#define RR_ADC_CHARGER_TEMP_STS 0xBA
+#define RR_ADC_CHARGER_TEMP_CFG 0xBB
+#define RR_ADC_CHARGER_TEMP_LSB 0xBC
+#define RR_ADC_CHARGER_TEMP_MSB 0xBD
+#define RR_ADC_CHARGER_HOT 0xBE
+#define RR_ADC_CHARGER_TOO_HOT 0xBF
+
+#define RR_ADC_GPIO_CTRL 0xC0
+#define RR_ADC_GPIO_TRIGGER 0xC1
+#define RR_ADC_GPIO_STS 0xC2
+#define RR_ADC_GPIO_LSB 0xC4
+#define RR_ADC_GPIO_MSB 0xC5
+
+#define RR_ADC_ATEST_CTRL 0xC8
+#define RR_ADC_ATEST_TRIGGER 0xC9
+#define RR_ADC_ATEST_STS 0xCA
+#define RR_ADC_ATEST_LSB 0xCC
+#define RR_ADC_ATEST_MSB 0xCD
+#define RR_ADC_SEC_ACCESS 0xD0
+
+#define RR_ADC_PERPH_RESET_CTL2 0xD9
+#define RR_ADC_PERPH_RESET_CTL3 0xDA
+#define RR_ADC_PERPH_RESET_CTL4 0xDB
+#define RR_ADC_INT_TEST1 0xE0
+#define RR_ADC_INT_TEST_VAL 0xE1
+
+#define RR_ADC_TM_TRIGGER_CTRLS 0xE2
+#define RR_ADC_TM_ADC_CTRLS 0xE3
+#define RR_ADC_TM_CNL_CTRL 0xE4
+#define RR_ADC_TM_BATT_ID_CTRL 0xE5
+#define RR_ADC_TM_THERM_CTRL 0xE6
+#define RR_ADC_TM_CONV_STS 0xE7
+#define RR_ADC_TM_ADC_READ_LSB 0xE8
+#define RR_ADC_TM_ADC_READ_MSB 0xE9
+#define RR_ADC_TM_ATEST_MUX_1 0xEA
+#define RR_ADC_TM_ATEST_MUX_2 0xEB
+#define RR_ADC_TM_REFERENCES 0xED
+#define RR_ADC_TM_MISC_CTL 0xEE
+#define RR_ADC_TM_RR_CTRL 0xEF
+
+#define RR_ADC_TRIGGER_EVERY_CYCLE BIT(7)
+#define RR_ADC_TRIGGER_CTL BIT(0)
+
+#define RR_ADC_BATT_ID_RANGE 820
+
+#define RR_ADC_BITS 10
+#define RR_ADC_CHAN_MSB (1 << RR_ADC_BITS)
+#define RR_ADC_FS_VOLTAGE_MV 2500
+
+/* BATT_THERM 0.25K/LSB */
+#define RR_ADC_BATT_THERM_LSB_K 4
+
+#define RR_ADC_TEMP_FS_VOLTAGE_NUM 5000000
+#define RR_ADC_TEMP_FS_VOLTAGE_DEN 3
+#define RR_ADC_DIE_TEMP_OFFSET 601400
+#define RR_ADC_DIE_TEMP_SLOPE 2
+#define RR_ADC_DIE_TEMP_OFFSET_MILLI_DEGC 25000
+
+#define RR_ADC_CHG_TEMP_GF_OFFSET_UV 1303168
+#define RR_ADC_CHG_TEMP_GF_SLOPE_UV_PER_C 3784
+#define RR_ADC_CHG_TEMP_SMIC_OFFSET_UV 1338433
+#define RR_ADC_CHG_TEMP_SMIC_SLOPE_UV_PER_C 3655
+#define RR_ADC_CHG_TEMP_660_GF_OFFSET_UV 1309001
+#define RR_ADC_CHG_TEMP_660_GF_SLOPE_UV_PER_C 3403
+#define RR_ADC_CHG_TEMP_660_SMIC_OFFSET_UV 1295898
+#define RR_ADC_CHG_TEMP_660_SMIC_SLOPE_UV_PER_C 3596
+#define RR_ADC_CHG_TEMP_660_MGNA_OFFSET_UV 1314779
+#define RR_ADC_CHG_TEMP_660_MGNA_SLOPE_UV_PER_C 3496
+#define RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC 25000
+#define RR_ADC_CHG_THRESHOLD_SCALE 4
+
+#define RR_ADC_VOLT_INPUT_FACTOR 8
+#define RR_ADC_CURR_INPUT_FACTOR 2000
+#define RR_ADC_CURR_USBIN_INPUT_FACTOR_MIL 1886
+#define RR_ADC_CURR_USBIN_660_FACTOR_MIL 9
+#define RR_ADC_CURR_USBIN_660_UV_VAL 579500
+
+#define RR_ADC_GPIO_FS_RANGE 5000
+#define RR_ADC_COHERENT_CHECK_RETRY 5
+#define RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN 16
+
+#define RR_ADC_STS_CHANNEL_READING_MASK GENMASK(1, 0)
+#define RR_ADC_STS_CHANNEL_STS BIT(1)
+
+#define RR_ADC_TP_REV_VERSION1 21
+#define RR_ADC_TP_REV_VERSION2 29
+#define RR_ADC_TP_REV_VERSION3 32
+
+#define RRADC_BATT_ID_DELAY_MAX 8
+
+enum rradc_channel_id {
+	RR_ADC_BATT_ID = 0,
+	RR_ADC_BATT_THERM,
+	RR_ADC_SKIN_TEMP,
+	RR_ADC_USBIN_I,
+	RR_ADC_USBIN_V,
+	RR_ADC_DCIN_I,
+	RR_ADC_DCIN_V,
+	RR_ADC_DIE_TEMP,
+	RR_ADC_CHG_TEMP,
+	RR_ADC_GPIO,
+	RR_ADC_CHAN_MAX
+};
+
+struct rradc_chip;
+
+/**
+ * struct rradc_channel - rradc channel data
+ * @label:		channel label
+ * @lsb:		Channel least significant byte
+ * @status:		Channel status address
+ * @size:		number of bytes to read
+ * @trigger_addr:	Trigger address, trigger is only used on some channels
+ * @trigger_mask:	Trigger mask
+ * @scale_fn:		Post process callback for channels which can't be exposed
+ *			as offset + scale.
+ */
+struct rradc_channel {
+	const char *label;
+	u8 lsb;
+	u8 status;
+	int size;
+	int trigger_addr;
+	int trigger_mask;
+	int (*scale_fn)(struct rradc_chip *chip, u16 adc_code, int *result);
+};
+
+struct rradc_chip {
+	struct device *dev;
+	const struct qcom_spmi_pmic *pmic;
+	/*
+	 * Lock held while doing channel conversion
+	 * involving multiple register read/writes
+	 */
+	struct mutex conversion_lock;
+	struct regmap *regmap;
+	u32 base;
+	int batt_id_delay;
+	u16 batt_id_data;
+};
+
+static const int batt_id_delays[] = { 0, 1, 4, 12, 20, 40, 60, 80 };
+static const struct rradc_channel rradc_chans[RR_ADC_CHAN_MAX];
+static const struct iio_chan_spec rradc_iio_chans[RR_ADC_CHAN_MAX];
+
+static int rradc_read(struct rradc_chip *chip, u16 addr, __le16 *buf, int len)
+{
+	int ret, retry_cnt = 0;
+	__le16 data_check[RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN / 2];
+
+	if (len > RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN) {
+		dev_err(chip->dev,
+			"Can't read more than %d bytes, but asked to read %d bytes.\n",
+			RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN, len);
+		return -EINVAL;
+	}
+
+	while (retry_cnt < RR_ADC_COHERENT_CHECK_RETRY) {
+		ret = regmap_bulk_read(chip->regmap, chip->base + addr, buf,
+				       len);
+		if (ret < 0) {
+			dev_err(chip->dev, "rr_adc reg 0x%x failed :%d\n", addr,
+				ret);
+			return ret;
+		}
+
+		ret = regmap_bulk_read(chip->regmap, chip->base + addr,
+				       data_check, len);
+		if (ret < 0) {
+			dev_err(chip->dev, "rr_adc reg 0x%x failed :%d\n", addr,
+				ret);
+			return ret;
+		}
+
+		if (memcmp(buf, data_check, len) != 0) {
+			retry_cnt++;
+			dev_dbg(chip->dev,
+				"coherent read error, retry_cnt:%d\n",
+				retry_cnt);
+			continue;
+		}
+
+		break;
+	}
+
+	if (retry_cnt == RR_ADC_COHERENT_CHECK_RETRY)
+		dev_err(chip->dev, "Retry exceeded for coherrency check\n");
+
+	return ret;
+}
+
+static int rradc_get_fab_coeff(struct rradc_chip *chip, int64_t *offset,
+			       int64_t *slope)
+{
+	if (chip->pmic->subtype == PM660_SUBTYPE) {
+		switch (chip->pmic->fab_id) {
+		case PM660_FAB_ID_GF:
+			*offset = RR_ADC_CHG_TEMP_660_GF_OFFSET_UV;
+			*slope = RR_ADC_CHG_TEMP_660_GF_SLOPE_UV_PER_C;
+			return 0;
+		case PM660_FAB_ID_TSMC:
+			*offset = RR_ADC_CHG_TEMP_660_SMIC_OFFSET_UV;
+			*slope = RR_ADC_CHG_TEMP_660_SMIC_SLOPE_UV_PER_C;
+			return 0;
+		default:
+			*offset = RR_ADC_CHG_TEMP_660_MGNA_OFFSET_UV;
+			*slope = RR_ADC_CHG_TEMP_660_MGNA_SLOPE_UV_PER_C;
+		}
+	} else if (chip->pmic->subtype == PMI8998_SUBTYPE) {
+		switch (chip->pmic->fab_id) {
+		case PMI8998_FAB_ID_GF:
+			*offset = RR_ADC_CHG_TEMP_GF_OFFSET_UV;
+			*slope = RR_ADC_CHG_TEMP_GF_SLOPE_UV_PER_C;
+			return 0;
+		case PMI8998_FAB_ID_SMIC:
+			*offset = RR_ADC_CHG_TEMP_SMIC_OFFSET_UV;
+			*slope = RR_ADC_CHG_TEMP_SMIC_SLOPE_UV_PER_C;
+			return 0;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	return -EINVAL;
+}
+
+/*
+ * These functions explicitly cast int64_t to int.
+ * They will never overflow, as the values are small enough.
+ */
+static int rradc_post_process_batt_id(struct rradc_chip *chip, u16 adc_code,
+				      int *result_ohms)
+{
+	uint32_t current_value;
+	int64_t r_id;
+
+	current_value = chip->batt_id_data;
+	r_id = ((int64_t)adc_code * RR_ADC_FS_VOLTAGE_MV);
+	r_id = div64_s64(r_id, (RR_ADC_CHAN_MSB * current_value));
+	*result_ohms = (int)(r_id * MILLI);
+
+	return 0;
+}
+
+static int rradc_enable_continuous_mode(struct rradc_chip *chip)
+{
+	int ret;
+
+	/* Clear channel log */
+	ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_LOG,
+				 RR_ADC_LOG_CLR_CTRL, RR_ADC_LOG_CLR_CTRL);
+	if (ret < 0) {
+		dev_err(chip->dev, "log ctrl update to clear failed:%d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_LOG,
+				 RR_ADC_LOG_CLR_CTRL, 0);
+	if (ret < 0) {
+		dev_err(chip->dev, "log ctrl update to not clear failed:%d\n",
+			ret);
+		return ret;
+	}
+
+	/* Switch to continuous mode */
+	ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_CTL,
+				 RR_ADC_CTL_CONTINUOUS_SEL,
+				 RR_ADC_CTL_CONTINUOUS_SEL);
+	if (ret < 0)
+		dev_err(chip->dev, "Update to continuous mode failed:%d\n",
+			ret);
+
+	return ret;
+}
+
+static int rradc_disable_continuous_mode(struct rradc_chip *chip)
+{
+	int ret;
+
+	/* Switch to non continuous mode */
+	ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_CTL,
+				 RR_ADC_CTL_CONTINUOUS_SEL, 0);
+	if (ret < 0)
+		dev_err(chip->dev, "Update to non-continuous mode failed:%d\n",
+			ret);
+
+	return ret;
+}
+
+static bool rradc_is_ready(struct rradc_chip *chip,
+			   enum rradc_channel_id chan_address)
+{
+	const struct rradc_channel *chan = &rradc_chans[chan_address];
+	int ret;
+	unsigned int status, mask;
+
+	/* BATT_ID STS bit does not get set initially */
+	switch (chan_address) {
+	case RR_ADC_BATT_ID:
+		mask = RR_ADC_STS_CHANNEL_STS;
+		break;
+	default:
+		mask = RR_ADC_STS_CHANNEL_READING_MASK;
+		break;
+	}
+
+	ret = regmap_read(chip->regmap, chip->base + chan->status, &status);
+	if (ret < 0 || !(status & mask))
+		return false;
+
+	return true;
+}
+
+static int rradc_read_status_in_cont_mode(struct rradc_chip *chip,
+					  enum rradc_channel_id chan_address)
+{
+	const struct rradc_channel *chan = &rradc_chans[chan_address];
+	const struct iio_chan_spec *iio_chan = &rradc_iio_chans[chan_address];
+	int ret, i;
+
+	if (chan->trigger_mask == 0) {
+		dev_err(chip->dev, "Channel doesn't have a trigger mask\n");
+		return -EINVAL;
+	}
+
+	ret = regmap_update_bits(chip->regmap, chip->base + chan->trigger_addr,
+				 chan->trigger_mask, chan->trigger_mask);
+	if (ret < 0) {
+		dev_err(chip->dev,
+			"Failed to apply trigger for channel '%s' ret=%d\n",
+			iio_chan->extend_name, ret);
+		return ret;
+	}
+
+	ret = rradc_enable_continuous_mode(chip);
+	if (ret < 0) {
+		dev_err(chip->dev, "Failed to switch to continuous mode\n");
+		goto disable_trigger;
+	}
+
+	/*
+	 * The wait/sleep values were found through trial and error,
+	 * this is mostly for the battery ID channel which takes some
+	 * time to settle.
+	 */
+	for (i = 0; i < 5; i++) {
+		if (rradc_is_ready(chip, chan_address))
+			break;
+		usleep_range(50000, 50000 + 500);
+	}
+
+	if (i == 5) {
+		dev_err(chip->dev, "Channel '%s' is not ready\n",
+			iio_chan->extend_name);
+		ret = -ETIMEDOUT;
+	}
+
+	rradc_disable_continuous_mode(chip);
+
+disable_trigger:
+	regmap_update_bits(chip->regmap, chip->base + chan->trigger_addr,
+			   chan->trigger_mask, 0);
+
+	return ret;
+}
+
+static int rradc_prepare_batt_id_conversion(struct rradc_chip *chip,
+					    enum rradc_channel_id chan_address,
+					    u16 *data)
+{
+	int ret;
+
+	ret = regmap_update_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_CTRL,
+				 RR_ADC_BATT_ID_CTRL_CHANNEL_CONV,
+				 RR_ADC_BATT_ID_CTRL_CHANNEL_CONV);
+	if (ret < 0) {
+		dev_err(chip->dev, "Enabling BATT ID channel failed:%d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_update_bits(chip->regmap,
+				 chip->base + RR_ADC_BATT_ID_TRIGGER,
+				 RR_ADC_TRIGGER_CTL, RR_ADC_TRIGGER_CTL);
+	if (ret < 0) {
+		dev_err(chip->dev, "BATT_ID trigger set failed:%d\n", ret);
+		goto out_disable_batt_id;
+	}
+
+	ret = rradc_read_status_in_cont_mode(chip, chan_address);
+
+	/* Reset registers back to default values */
+	regmap_update_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_TRIGGER,
+			   RR_ADC_TRIGGER_CTL, 0);
+
+out_disable_batt_id:
+	regmap_update_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_CTRL,
+			   RR_ADC_BATT_ID_CTRL_CHANNEL_CONV, 0);
+
+	return ret;
+}
+
+static int rradc_do_conversion(struct rradc_chip *chip,
+			       enum rradc_channel_id chan_address, u16 *data)
+{
+	const struct rradc_channel *chan = &rradc_chans[chan_address];
+	const struct iio_chan_spec *iio_chan = &rradc_iio_chans[chan_address];
+	int ret;
+	__le16 buf[3];
+
+	mutex_lock(&chip->conversion_lock);
+
+	switch (chan_address) {
+	case RR_ADC_BATT_ID:
+		ret = rradc_prepare_batt_id_conversion(chip, chan_address, data);
+		if (ret < 0) {
+			dev_err(chip->dev, "Battery ID conversion failed:%d\n",
+				ret);
+			goto unlock_out;
+		}
+		break;
+
+	case RR_ADC_USBIN_V:
+	case RR_ADC_DIE_TEMP:
+		ret = rradc_read_status_in_cont_mode(chip, chan_address);
+		if (ret < 0) {
+			dev_err(chip->dev,
+				"Error reading in continuous mode:%d\n", ret);
+			goto unlock_out;
+		}
+		break;
+	default:
+		if (!rradc_is_ready(chip, chan_address)) {
+			/*
+			 * Usually this means the channel isn't attached, for example
+			 * the in_voltage_usbin_v_input channel will not be ready if
+			 * no USB cable is attached
+			 */
+			dev_dbg(chip->dev, "channel '%s' is not ready\n",
+				iio_chan->extend_name);
+			ret = -ENODATA;
+			goto unlock_out;
+		}
+		break;
+	}
+
+	ret = rradc_read(chip, chan->lsb, buf, chan->size);
+	if (ret) {
+		dev_err(chip->dev, "read data failed\n");
+		goto unlock_out;
+	}
+
+	/*
+	 * For the battery ID we read the register for every ID ADC and then
+	 * see which one is actually connected.
+	 */
+	if (chan_address == RR_ADC_BATT_ID) {
+		u16 batt_id_150 = le16_to_cpu(buf[2]);
+		u16 batt_id_15 = le16_to_cpu(buf[1]);
+		u16 batt_id_5 = le16_to_cpu(buf[0]);
+
+		if (!batt_id_150 && !batt_id_15 && !batt_id_5) {
+			dev_err(chip->dev,
+				"Invalid batt_id values with all zeros\n");
+			ret = -EINVAL;
+			goto unlock_out;
+		}
+
+		if (batt_id_150 <= RR_ADC_BATT_ID_RANGE) {
+			*data = batt_id_150;
+			chip->batt_id_data = 150;
+		} else if (batt_id_15 <= RR_ADC_BATT_ID_RANGE) {
+			*data = batt_id_15;
+			chip->batt_id_data = 15;
+		} else {
+			*data = batt_id_5;
+			chip->batt_id_data = 5;
+		}
+	} else {
+		/*
+		 * All of the other channels are either 1 or 2 bytes.
+		 * We can rely on the second byte being 0 for 1-byte channels.
+		 */
+		*data = le16_to_cpu(buf[0]);
+	}
+
+unlock_out:
+	mutex_unlock(&chip->conversion_lock);
+
+	return ret;
+}
+
+static int rradc_read_scale(struct rradc_chip *chip, int chan_address, int *val,
+			    int *val2)
+{
+	int64_t fab_offset, fab_slope;
+	int ret;
+
+	ret = rradc_get_fab_coeff(chip, &fab_offset, &fab_slope);
+	if (ret < 0) {
+		dev_err(chip->dev, "Unable to get fab id coefficients\n");
+		return -EINVAL;
+	}
+
+	switch (chan_address) {
+	case RR_ADC_SKIN_TEMP:
+		*val = MILLI;
+		*val2 = RR_ADC_BATT_THERM_LSB_K;
+		return IIO_VAL_FRACTIONAL;
+	case RR_ADC_USBIN_I:
+		*val = RR_ADC_CURR_USBIN_INPUT_FACTOR_MIL *
+		       RR_ADC_FS_VOLTAGE_MV;
+		*val2 = RR_ADC_CHAN_MSB;
+		return IIO_VAL_FRACTIONAL;
+	case RR_ADC_DCIN_I:
+		*val = RR_ADC_CURR_INPUT_FACTOR * RR_ADC_FS_VOLTAGE_MV;
+		*val2 = RR_ADC_CHAN_MSB;
+		return IIO_VAL_FRACTIONAL;
+	case RR_ADC_USBIN_V:
+	case RR_ADC_DCIN_V:
+		*val = RR_ADC_VOLT_INPUT_FACTOR * RR_ADC_FS_VOLTAGE_MV * MILLI;
+		*val2 = RR_ADC_CHAN_MSB;
+		return IIO_VAL_FRACTIONAL;
+	case RR_ADC_GPIO:
+		*val = RR_ADC_GPIO_FS_RANGE;
+		*val2 = RR_ADC_CHAN_MSB;
+		return IIO_VAL_FRACTIONAL;
+	case RR_ADC_CHG_TEMP:
+		/*
+		 * We divide val2 by MILLI instead of multiplying val
+		 * to avoid an integer overflow.
+		 */
+		*val = -RR_ADC_TEMP_FS_VOLTAGE_NUM;
+		*val2 = div64_s64(RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MSB *
+					  fab_slope,
+				  MILLI);
+
+		return IIO_VAL_FRACTIONAL;
+	case RR_ADC_DIE_TEMP:
+		*val = RR_ADC_TEMP_FS_VOLTAGE_NUM;
+		*val2 = RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MSB *
+			RR_ADC_DIE_TEMP_SLOPE;
+
+		return IIO_VAL_FRACTIONAL;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int rradc_read_offset(struct rradc_chip *chip, int chan_address, int *val)
+{
+	int64_t fab_offset, fab_slope;
+	int64_t offset1, offset2;
+	int ret;
+
+	switch (chan_address) {
+	case RR_ADC_SKIN_TEMP:
+		/*
+		 * Offset from kelvin to degC, divided by the
+		 * scale factor (250). We lose some precision here.
+		 * 273150 / 250 = 1092.6
+		 */
+		*val = div64_s64(ABSOLUTE_ZERO_MILLICELSIUS,
+				 (MILLI / RR_ADC_BATT_THERM_LSB_K));
+		return IIO_VAL_INT;
+	case RR_ADC_CHG_TEMP:
+		ret = rradc_get_fab_coeff(chip, &fab_offset, &fab_slope);
+		if (ret < 0) {
+			dev_err(chip->dev,
+				"Unable to get fab id coefficients\n");
+			return -EINVAL;
+		}
+		offset1 = -(fab_offset * RR_ADC_TEMP_FS_VOLTAGE_DEN *
+			    RR_ADC_CHAN_MSB);
+		offset1 += (int64_t)RR_ADC_TEMP_FS_VOLTAGE_NUM / 2ULL;
+		offset1 = div64_s64(offset1,
+				    (int64_t)(RR_ADC_TEMP_FS_VOLTAGE_NUM));
+
+		offset2 = (int64_t)RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC *
+			  RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MSB *
+			  (int64_t)fab_slope;
+		offset2 += ((int64_t)MILLI * RR_ADC_TEMP_FS_VOLTAGE_NUM) / 2;
+		offset2 = div64_s64(
+			offset2, ((int64_t)MILLI * RR_ADC_TEMP_FS_VOLTAGE_NUM));
+
+		/*
+		 * The -1 is to compensate for lost precision.
+		 * It should actually be -0.7906976744186046.
+		 * This works out to every value being off
+		 * by about +0.091 degrees C after applying offset and scale.
+		 */
+		*val = (int)(offset1 - offset2 - 1);
+		return IIO_VAL_INT;
+	case RR_ADC_DIE_TEMP:
+		offset1 = -RR_ADC_DIE_TEMP_OFFSET *
+			  (int64_t)RR_ADC_TEMP_FS_VOLTAGE_DEN *
+			  (int64_t)RR_ADC_CHAN_MSB;
+		offset1 = div64_s64(offset1, RR_ADC_TEMP_FS_VOLTAGE_NUM);
+
+		offset2 = -(int64_t)RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC *
+			  RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MSB *
+			  RR_ADC_DIE_TEMP_SLOPE;
+		offset2 = div64_s64(offset2,
+				    ((int64_t)RR_ADC_TEMP_FS_VOLTAGE_NUM));
+
+		/*
+		 * The result is -339, it should be -338.69789, this results
+		 * in the calculated die temp being off by
+		 * -0.004 - -0.0175 degrees C
+		 */
+		*val = (int)(offset1 - offset2);
+		return IIO_VAL_INT;
+	default:
+		break;
+	}
+	return -EINVAL;
+}
+
+static int rradc_read_raw(struct iio_dev *indio_dev,
+			  struct iio_chan_spec const *chan_spec, int *val,
+			  int *val2, long mask)
+{
+	struct rradc_chip *chip = iio_priv(indio_dev);
+	const struct rradc_channel *chan;
+	int ret;
+	u16 adc_code;
+
+	if (chan_spec->address >= RR_ADC_CHAN_MAX) {
+		dev_err(chip->dev, "Invalid channel index:%lu\n",
+			chan_spec->address);
+		return -EINVAL;
+	}
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		return rradc_read_scale(chip, chan_spec->address, val, val2);
+	case IIO_CHAN_INFO_OFFSET:
+		return rradc_read_offset(chip, chan_spec->address, val);
+	case IIO_CHAN_INFO_RAW:
+		ret = rradc_do_conversion(chip, chan_spec->address, &adc_code);
+		if (ret < 0)
+			return ret;
+
+		*val = adc_code;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_PROCESSED:
+		chan = &rradc_chans[chan_spec->address];
+		if (!chan->scale_fn)
+			return -EINVAL;
+		ret = rradc_do_conversion(chip, chan_spec->address, &adc_code);
+		if (ret < 0)
+			return ret;
+
+		*val = chan->scale_fn(chip, adc_code, val);
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int rradc_read_label(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan, char *label)
+{
+	return snprintf(label, PAGE_SIZE, "%s\n",
+			rradc_chans[chan->address].label);
+}
+
+static const struct iio_info rradc_info = {
+	.read_raw = rradc_read_raw,
+	.read_label = rradc_read_label,
+};
+
+static const struct rradc_channel rradc_chans[RR_ADC_CHAN_MAX] = {
+	{
+		.label = "batt_id",
+		.scale_fn = rradc_post_process_batt_id,
+		.lsb = RR_ADC_BATT_ID_5_LSB,
+		.status = RR_ADC_BATT_ID_STS,
+		.size = 6,
+		.trigger_addr = RR_ADC_BATT_ID_TRIGGER,
+		.trigger_mask = BIT(0),
+	}, {
+		.label = "batt",
+		.lsb = RR_ADC_BATT_THERM_LSB,
+		.status = RR_ADC_BATT_THERM_STS,
+		.size = 2,
+		.trigger_addr = RR_ADC_BATT_THERM_TRIGGER,
+	}, {
+		.label = "pmi8998_skin",
+		.lsb = RR_ADC_SKIN_TEMP_LSB,
+		.status = RR_ADC_AUX_THERM_STS,
+		.size = 2,
+		.trigger_addr = RR_ADC_AUX_THERM_TRIGGER,
+	}, {
+		.label = "usbin_i",
+		.lsb = RR_ADC_USB_IN_I_LSB,
+		.status = RR_ADC_USB_IN_I_STS,
+		.size = 2,
+		.trigger_addr = RR_ADC_USB_IN_I_TRIGGER,
+	}, {
+		.label = "usbin_v",
+		.lsb = RR_ADC_USB_IN_V_LSB,
+		.status = RR_ADC_USB_IN_V_STS,
+		.size = 2,
+		.trigger_addr = RR_ADC_USB_IN_V_TRIGGER,
+		.trigger_mask = BIT(7),
+	}, {
+		.label = "dcin_i",
+		.lsb = RR_ADC_DC_IN_I_LSB,
+		.status = RR_ADC_DC_IN_I_STS,
+		.size = 2,
+		.trigger_addr = RR_ADC_DC_IN_I_TRIGGER,
+	}, {
+		.label = "dcin_v",
+		.lsb = RR_ADC_DC_IN_V_LSB,
+		.status = RR_ADC_DC_IN_V_STS,
+		.size = 2,
+		.trigger_addr = RR_ADC_DC_IN_V_TRIGGER,
+	}, {
+		.label = "pmi8998_die",
+		.lsb = RR_ADC_PMI_DIE_TEMP_LSB,
+		.status = RR_ADC_PMI_DIE_TEMP_STS,
+		.size = 2,
+		.trigger_addr = RR_ADC_PMI_DIE_TEMP_TRIGGER,
+		.trigger_mask = RR_ADC_TRIGGER_EVERY_CYCLE,
+	}, {
+		.label = "chg",
+		.lsb = RR_ADC_CHARGER_TEMP_LSB,
+		.status = RR_ADC_CHARGER_TEMP_STS,
+		.size = 2,
+		.trigger_addr = RR_ADC_CHARGER_TEMP_TRIGGER,
+	}, {
+		.label = "gpio",
+		.lsb = RR_ADC_GPIO_LSB,
+		.status = RR_ADC_GPIO_STS,
+		.size = 2,
+		.trigger_addr = RR_ADC_GPIO_TRIGGER,
+	},
+};
+
+static const struct iio_chan_spec rradc_iio_chans[RR_ADC_CHAN_MAX] = {
+	{
+		.type = IIO_RESISTANCE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.address = RR_ADC_BATT_ID,
+		.channel = 0,
+		.indexed = 1,
+	}, {
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.address = RR_ADC_BATT_THERM,
+		.channel = 0,
+		.indexed = 1,
+	}, {
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE) |
+				      BIT(IIO_CHAN_INFO_OFFSET),
+		.address = RR_ADC_SKIN_TEMP,
+		.channel = 1,
+		.indexed = 1,
+	}, {
+		.type = IIO_CURRENT,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE),
+		.address = RR_ADC_USBIN_I,
+		.channel = 0,
+		.indexed = 1,
+	}, {
+		.type = IIO_VOLTAGE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE),
+		.address = RR_ADC_USBIN_V,
+		.channel = 0,
+		.indexed = 1,
+	}, {
+		.type = IIO_CURRENT,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE),
+		.address = RR_ADC_DCIN_I,
+		.channel = 1,
+		.indexed = 1,
+	}, {
+		.type = IIO_VOLTAGE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE),
+		.address = RR_ADC_DCIN_V,
+		.channel = 1,
+		.indexed = 1,
+	}, {
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE) |
+				      BIT(IIO_CHAN_INFO_OFFSET),
+		.address = RR_ADC_DIE_TEMP,
+		.channel = 2,
+		.indexed = 1,
+	}, {
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_OFFSET) |
+				      BIT(IIO_CHAN_INFO_SCALE),
+		.address = RR_ADC_CHG_TEMP,
+		.channel = 3,
+		.indexed = 1,
+	}, {
+		.type = IIO_VOLTAGE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE),
+		.address = RR_ADC_GPIO,
+		.channel = 2,
+		.indexed = 1,
+	},
+};
+
+static int rradc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct iio_dev *indio_dev;
+	struct rradc_chip *chip;
+	int ret, i, batt_id_delay;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*chip));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	chip = iio_priv(indio_dev);
+	chip->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!chip->regmap) {
+		dev_err(dev, "Couldn't get parent's regmap\n");
+		return -EINVAL;
+	}
+
+	chip->dev = dev;
+	mutex_init(&chip->conversion_lock);
+
+	ret = device_property_read_u32(dev, "reg", &chip->base);
+	if (ret < 0) {
+		dev_err(chip->dev, "Couldn't find reg address, ret = %d\n",
+			ret);
+		return ret;
+	}
+
+	batt_id_delay = -1;
+	ret = device_property_read_u32(dev, "qcom,batt-id-delay-ms",
+				       &batt_id_delay);
+	if (!ret) {
+		for (i = 0; i < RRADC_BATT_ID_DELAY_MAX; i++) {
+			if (batt_id_delay == batt_id_delays[i])
+				break;
+		}
+		if (i == RRADC_BATT_ID_DELAY_MAX)
+			batt_id_delay = -1;
+	}
+
+	if (batt_id_delay >= 0) {
+		batt_id_delay = FIELD_PREP(BATT_ID_SETTLE_MASK, batt_id_delay);
+		ret = regmap_update_bits(chip->regmap,
+					 chip->base + RR_ADC_BATT_ID_CFG,
+					 batt_id_delay, batt_id_delay);
+		if (ret < 0) {
+			dev_err(chip->dev,
+				"BATT_ID settling time config failed:%d\n",
+				ret);
+		}
+	}
+
+	/* Get the PMIC revision, we need it to handle some varying coefficients */
+	chip->pmic = qcom_pmic_get(chip->dev);
+	if (IS_ERR(chip->pmic)) {
+		dev_err(chip->dev, "Unable to get reference to PMIC device\n");
+		return PTR_ERR(chip->pmic);
+	}
+
+	switch (chip->pmic->subtype) {
+	case PMI8998_SUBTYPE:
+		indio_dev->name = "pmi8998-rradc";
+		break;
+	case PM660_SUBTYPE:
+		indio_dev->name = "pm660-rradc";
+		break;
+	default:
+		indio_dev->name = DRIVER_NAME;
+		break;
+	}
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &rradc_info;
+	indio_dev->channels = rradc_iio_chans;
+	indio_dev->num_channels = ARRAY_SIZE(rradc_iio_chans);
+
+	return devm_iio_device_register(dev, indio_dev);
+}
+
+static const struct of_device_id rradc_match_table[] = {
+	{ .compatible = "qcom,pm660-rradc" },
+	{ .compatible = "qcom,pmi8998-rradc" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, rradc_match_table);
+
+static struct platform_driver rradc_driver = {
+	.driver		= {
+		.name		= DRIVER_NAME,
+		.of_match_table	= rradc_match_table,
+	},
+	.probe = rradc_probe,
+};
+module_platform_driver(rradc_driver);
+
+MODULE_DESCRIPTION("QCOM SPMI PMIC RR ADC driver");
+MODULE_AUTHOR("Caleb Connolly <[email protected]>");
+MODULE_LICENSE("GPL v2");
#20 lore raw

Re: [PATCH v13 5/9] iio: adc: qcom-spmi-rradc: introduce round robin adc

Quoted 11 lines · Jonathan Cameron
Quoted 8 lines · On Wed, 23 Mar 2022 16:28:16 +0000 Caleb Connolly <[email protected]>…

From: Caleb Connolly <[email protected]>

The Round Robin ADC is responsible for reading data about the rate of charge from the USB or DC input ports, it can also read the battery ID (resistence), skin temperature and the die temperature of the pmic. It is found on the PMI8998 and PM660 Qualcomm PMICs.

Quoted 9 lines

Whilst I said this patch was fine a few versions ago I didn't add a tag on basis I would probably end up picking it up.

To make things more flexible, I'll add one and either Lee or I can do the immutable branch once Lee has had a chance to take a look and is happy with the mfd parts.

Are either of you planning to pick up the driver changes?

The dts changes can be merged independently, so I would prefer to pick those through my tree. But I would like to know that the binding and implementation is agreed upon before doing so.

Thanks,
Bjorn

#21 lore raw

Re: [PATCH v13 5/9] iio: adc: qcom-spmi-rradc: introduce round robin adc

Quoted 20 lines · On Tue, 12 Apr 2022 20:08:03 -0700 Bjorn Andersson…
Quoted 18 lines · Jonathan Cameron
Quoted 8 lines · On Wed, 23 Mar 2022 16:28:16 +0000 Caleb Connolly <[email protected]>…

From: Caleb Connolly <[email protected]>

The Round Robin ADC is responsible for reading data about the rate of charge from the USB or DC input ports, it can also read the battery ID (resistence), skin temperature and the die temperature of the pmic. It is found on the PMI8998 and PM660 Qualcomm PMICs.

Whilst I said this patch was fine a few versions ago I didn't add a tag on basis I would probably end up picking it up.

To make things more flexible, I'll add one and either Lee or I can do the immutable branch once Lee has had a chance to take a look and is happy with the mfd parts.

Quoted 8 lines
Quoted 2 lines

Are either of you planning to pick up the driver changes?

The dts changes can be merged independently, so I would prefer to pick those through my tree. But I would like to know that the binding and implementation is agreed upon before doing so.

I need an Ack from Lee for the mfd changes and ideally Stephen for the SPMI patch.

Lee, guessing you are busy, but if you have a chance to check this set over that would be great.

Jonathan

Quoted 3 lines

Thanks,
Bjorn

#22 lore raw

PATCH v13 6/9 arm64: dts: qcom: pmi8998: add rradc node

In reply to Caleb Connolly

From: Caleb Connolly <[email protected]>

Add a DT node for the Round Robin ADC found in the PMI8998 PMIC.

---
 arch/arm64/boot/dts/qcom/pmi8998.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)
arch/arm64/boot/dts/qcom/pmi8998.dtsi +8 -0
index 0fef5f113f05..da10668c361d 100644
@@ -18,6 +18,14 @@ pmi8998_gpio: gpios@c000 {
 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};
+
+		pmi8998_rradc: rradc@4500 {
+			compatible = "qcom,pmi8998-rradc";
+			reg = <0x4500>;
+			#io-channel-cells = <1>;
+
+			status = "disabled";
+		};
 	};
 
 	pmi8998_lsid1: pmic@3 {
Signature · 1 line
2.35.1
#23 lore raw

PATCH v13 7/9 arm64: dts: qcom: sdm845-oneplus: enable rradc

In reply to Caleb Connolly

From: Caleb Connolly <[email protected]>

Enable the RRADC for the OnePlus 6.

---
 arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi +4 -0
index 7f42e5315ecb..e8287cf02511 100644
@@ -450,6 +450,10 @@ pinconf {
 	};
 };
 
+&pmi8998_rradc {
+	status = "okay";
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
Signature · 1 line
2.35.1
#24 lore raw

PATCH v13 8/9 arm64: dts: qcom: sdm845-db845c: enable rradc

In reply to Caleb Connolly

From: Caleb Connolly <[email protected]>

Enable the Round Robin ADC for the db845c.

---
 arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/qcom/sdm845-db845c.dts +4 -0
index 13f80a0b6faa..1c452b458121 100644
@@ -595,6 +595,10 @@ resin {
 	};
 };
 
+&pmi8998_rradc {
+	status = "okay";
+};
+
 /* QUAT I2S Uses 4 I2S SD Lines for audio on LT9611 HDMI Bridge */
 &q6afedai {
 	qi2s@22 {
Signature · 1 line
2.35.1
#25 lore raw

PATCH v13 9/9 arm64: dts: qcom: sdm845-xiaomi-beryllium: enable rradc

In reply to Caleb Connolly

From: Caleb Connolly <[email protected]>

Enable the PMI8998 RRADC.

---
 arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts +4 -0
index 367389526b41..b3b6aa4e0fa3 100644
@@ -312,6 +312,10 @@ resin {
 	};
 };
 
+&pmi8998_rradc {
+	status = "okay";
+};
+
 /* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */
 &q6afedai {
 	qi2s@22 {
Signature · 1 line
2.35.1