ARM: dts: aspeed: romed8hm3: Add lm25066 sense resistor values
Subsystems (2)
PATCH 1/2 ARM: dts: aspeed: romed8hm3: Add lm25066 sense resistor values
With this property set the sensor readings from these devices can now be calibrated properly.
--- arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts +2 -0
@@ -100,12 +100,14 @@ w83773g at 4c { lm25066 at 40 { compatible = "lm25066"; reg = <0x40>; + shunt-resistor-micro-ohms = <1000>; }; /* 12VSB PMIC */ lm25066 at 41 { compatible = "lm25066"; reg = <0x41>; + shunt-resistor-micro-ohms = <10000>; }; };
Signature · 1 line
2.35.1
PATCH 2/2 ARM: dts: aspeed: romed8hm3: Fix GPIOB0 name
This GPIO was mislabeled as DDR_MEM_TEMP in the schematic; after a correction from ASRock Rack its name now reflects its actual functionality (POST_COMPLETE_N).
--- arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts +1 -1
@@ -198,7 +198,7 @@ &gpio { gpio-line-names = /* A */ "LOCATORLED_STATUS_N", "BMC_MAC2_INTB", "NMI_BTN_N", "BMC_NMI", "", "", "", "", - /* B */ "DDR_MEM_TEMP", "", "", "", "", "", "", "", + /* B */ "POST_COMPLETE_N", "", "", "", "", "", "", "", /* C */ "", "", "", "", "PCIE_HP_SEL_N", "PCIE_SATA_SEL_N", "LOCATORBTN", "", /* D */ "BMC_PSIN", "BMC_PSOUT", "BMC_RESETCON", "RESETCON", "", "", "", "PSU_FAN_FAIL_N",
Signature · 1 line
2.35.1
Re: [PATCH 2/2] ARM: dts: aspeed: romed8hm3: Fix GPIOB0 name
Quoted 4 lines · Zev Weiss
This GPIO was mislabeled as
DDR_MEM_TEMPin the schematic; after a correction from ASRock Rack its name now reflects its actual functionality (POST_COMPLETE_N).
Those are quite different functions :)
Quoted 2 lines
Signed-off-by Zev Weiss <[email protected]>
I'll send some fixes in after -rc1.
Quoted 20 lines
--- arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts +1
-2@@ -198,7 +198,7 @@ &gpio { gpio-line-names = /* A */ "LOCATORLED_STATUS_N", "BMC_MAC2_INTB", "NMI_BTN_N", "BMC_NMI", "", "", "", "", - /* B */ "DDR_MEM_TEMP", "", "", "", "", "", "", "", + /* B */ "POST_COMPLETE_N", "", "", "", "", "", "", "", /* C */ "", "", "", "", "PCIE_HP_SEL_N", "PCIE_SATA_SEL_N", "LOCATORBTN", "", /* D */ "BMC_PSIN", "BMC_PSOUT", "BMC_RESETCON", "RESETCON", "", "", "", "PSU_FAN_FAIL_N", --2.35.1
Re: [PATCH 2/2] ARM: dts: aspeed: romed8hm3: Fix GPIOB0 name
Quoted 8 lines · Joel Stanley
Quoted 4 lines · Zev Weiss
This GPIO was mislabeled as
DDR_MEM_TEMPin the schematic; after a correction from ASRock Rack its name now reflects its actual functionality (POST_COMPLETE_N).Those are quite different functions :)
Yes, rather -- that little tidbit resolved quite a bit of head-scratching that had been going on...
Quoted 4 lines
Quoted 2 lines
Signed-off-by Zev Weiss <[email protected]>Fixes a9a3d60b937a ("ARM: dts: aspeed: Add ASRock ROMED8HM3 BMC")
Ah yes, I'll try to remember to include those to start with.
Quoted 4 lines
Reviewed-by Joel Stanley <[email protected]>I'll send some fixes in after -rc1.
Thanks!
Zev
Quoted 5 lines · Zev Weiss
With this property set the sensor readings from these devices can now be calibrated properly.
Signed-off-by Zev Weiss <[email protected]>
I guess:
I'll send some fixes in after -rc1.
Quoted 26 lines
--- arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts | 2 ++ 1 file changed, 2 insertions(+)arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts +2
-1@@ -100,12 +100,14 @@ w83773g at 4c { lm25066 at 40 { compatible = "lm25066"; reg = <0x40>; + shunt-resistor-micro-ohms = <1000>; }; /* 12VSB PMIC */ lm25066 at 41 { compatible = "lm25066"; reg = <0x41>; + shunt-resistor-micro-ohms = <10000>; }; }; --2.35.1