Skip to contentSkip to conversation

ath5k: fix OOB in ath5k_eeprom_read_pcal_info_5111

PATCH New Sasha Levin 1 participant 22 messages Apr 1, 2022

Subsystems (10)
lore
Share & tools
lore

Sasha Levin

author maintainer
#0 lore raw

PATCH 1/22 ath5k: fix OOB in ath5k_eeprom_read_pcal_info_5111

From: Zekun Shen <[email protected]>

[ Upstream commit 564d4eceb97eaf381dd6ef6470b06377bb50c95a ]

The bug was found during fuzzing. Stacktrace locates it in ath5k_eeprom_convert_pcal_info_5111.
When none of the curve is selected in the loop, idx can go up to AR5K_EEPROM_N_PD_CURVES. The line makes pd out of bound. pd = &chinfo[pier].pd_curves[idx];

There are many OOB writes using pd later in the code. So I added a sanity check for idx. Checks for other loops involving AR5K_EEPROM_N_PD_CURVES are not needed as the loop index is not used outside the loops.

The patch is NOT tested with real device.

The following is the fuzzing report

BUG: KASAN: slab-out-of-bounds in ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
Write of size 1 at addr ffff8880174a4d60 by task modprobe/214

CPU: 0 PID: 214 Comm: modprobe Not tainted 5.6.0 #1
Call Trace:
 dump_stack+0x76/0xa0
 print_address_description.constprop.0+0x16/0x200
 ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
 ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
 __kasan_report.cold+0x37/0x7c
 ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
 kasan_report+0xe/0x20
 ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
 ? apic_timer_interrupt+0xa/0x20
 ? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k]
 ? ath5k_pci_eeprom_read+0x228/0x3c0 [ath5k]
 ath5k_eeprom_init+0x2513/0x6290 [ath5k]
 ? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k]
 ? usleep_range+0xb8/0x100
 ? apic_timer_interrupt+0xa/0x20
 ? ath5k_eeprom_read_pcal_info_2413+0x2f20/0x2f20 [ath5k]
 ath5k_hw_init+0xb60/0x1970 [ath5k]
 ath5k_init_ah+0x6fe/0x2530 [ath5k]
 ? kasprintf+0xa6/0xe0
 ? ath5k_stop+0x140/0x140 [ath5k]
 ? _dev_notice+0xf6/0xf6
 ? apic_timer_interrupt+0xa/0x20
 ath5k_pci_probe.cold+0x29a/0x3d6 [ath5k]
 ? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k]
 ? mutex_lock+0x89/0xd0
 ? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k]
 local_pci_probe+0xd3/0x160
 pci_device_probe+0x23f/0x3e0
 ? pci_device_remove+0x280/0x280
 ? pci_device_remove+0x280/0x280
 really_probe+0x209/0x5d0
---
 drivers/net/wireless/ath/ath5k/eeprom.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/net/wireless/ath/ath5k/eeprom.c +3 -0
index 94d34ee02265..01163b333945 100644
@@ -746,6 +746,9 @@ ath5k_eeprom_convert_pcal_info_5111(struct ath5k_hw *ah, int mode,
 			}
 		}
 
+		if (idx == AR5K_EEPROM_N_PD_CURVES)
+			goto err_out;
+
 		ee->ee_pd_gains[mode] = 1;
 
 		pd = &chinfo[pier].pd_curves[idx];
Signature · 1 line
2.34.1
author maintainer
#1 lore raw

PATCH 2/22 ptp: replace snprintf with sysfs_emit

From: Yang Guang <[email protected]>

[ Upstream commit e2cf07654efb0fd7bbcb475c6f74be7b5755a8fd ]

coccinelle report:
./drivers/ptp/ptp_sysfs.c:17:8-16:
WARNING: use scnprintf or sprintf
./drivers/ptp/ptp_sysfs.c:390:8-16:
WARNING: use scnprintf or sprintf

Use sysfs_emit instead of scnprintf or sprintf makes more sense.

---
 drivers/ptp/ptp_sysfs.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/ptp/ptp_sysfs.c +2 -2
index 48401dfcd999..f97a5eefa2e2 100644
@@ -26,7 +26,7 @@ static ssize_t clock_name_show(struct device *dev,
 			       struct device_attribute *attr, char *page)
 {
 	struct ptp_clock *ptp = dev_get_drvdata(dev);
-	return snprintf(page, PAGE_SIZE-1, "%s\n", ptp->info->name);
+	return sysfs_emit(page, "%s\n", ptp->info->name);
 }
 static DEVICE_ATTR_RO(clock_name);
 
@@ -240,7 +240,7 @@ static ssize_t ptp_pin_show(struct device *dev, struct device_attribute *attr,
 
 	mutex_unlock(&ptp->pincfg_mux);
 
-	return snprintf(page, PAGE_SIZE, "%u %u\n", func, chan);
+	return sysfs_emit(page, "%u %u\n", func, chan);
 }
 
 static ssize_t ptp_pin_store(struct device *dev, struct device_attribute *attr,
Signature · 1 line
2.34.1
author maintainer
#2 lore raw

PATCH 3/22 powerpc: dts: t104xrdb: fix phy type for FMAN 4/5

In reply to Sasha Levin

From: Maxim Kiselev <[email protected]>

[ Upstream commit 17846485dff91acce1ad47b508b633dffc32e838 ]

T1040RDB has two RTL8211E-VB phys which requires setting of internal delays for correct work.

Changing the phy-connection-type property to rgmii-id will fix this issue.

---
 arch/powerpc/boot/dts/fsl/t104xrdb.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/powerpc/boot/dts/fsl/t104xrdb.dtsi +2 -2
index 5fdddbd2a62b..b0a9beab1c26 100644
@@ -139,12 +139,12 @@ pca9546@77 {
 		fman@400000 {
 			ethernet@e6000 {
 				phy-handle = <&phy_rgmii_0>;
-				phy-connection-type = "rgmii";
+				phy-connection-type = "rgmii-id";
 			};
 
 			ethernet@e8000 {
 				phy-handle = <&phy_rgmii_1>;
-				phy-connection-type = "rgmii";
+				phy-connection-type = "rgmii-id";
 			};
 
 			mdio0: mdio@fc000 {
Signature · 1 line
2.34.1
author maintainer
#3 lore raw

PATCH 4/22 scsi: mvsas: Replace snprintf() with sysfs_emit()

In reply to Sasha Levin

From: Yang Guang <[email protected]>

[ Upstream commit 0ad3867b0f13e45cfee5a1298bfd40eef096116c ]

coccinelle report:
./drivers/scsi/mvsas/mv_init.c:699:8-16:
WARNING: use scnprintf or sprintf
./drivers/scsi/mvsas/mv_init.c:747:8-16:
WARNING: use scnprintf or sprintf

Use sysfs_emit() instead of scnprintf() or sprintf().

---
 drivers/scsi/mvsas/mv_init.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/scsi/mvsas/mv_init.c +2 -2
index 718c88de328b..f6070b1fe1d8 100644
@@ -729,7 +729,7 @@ static ssize_t
 mvs_show_driver_version(struct device *cdev,
 		struct device_attribute *attr,  char *buffer)
 {
-	return snprintf(buffer, PAGE_SIZE, "%s\n", DRV_VERSION);
+	return sysfs_emit(buffer, "%s\n", DRV_VERSION);
 }
 
 static DEVICE_ATTR(driver_version,
@@ -781,7 +781,7 @@ mvs_store_interrupt_coalescing(struct device *cdev,
 static ssize_t mvs_show_interrupt_coalescing(struct device *cdev,
 			struct device_attribute *attr, char *buffer)
 {
-	return snprintf(buffer, PAGE_SIZE, "%d\n", interrupt_coalescing);
+	return sysfs_emit(buffer, "%d\n", interrupt_coalescing);
 }
 
 static DEVICE_ATTR(interrupt_coalescing,
Signature · 1 line
2.34.1
author maintainer
#4 lore raw

PATCH 5/22 scsi: bfa: Replace snprintf() with sysfs_emit()

In reply to Sasha Levin

From: Yang Guang <[email protected]>

[ Upstream commit 2245ea91fd3a04cafbe2f54911432a8657528c3b ]

coccinelle report:
./drivers/scsi/bfa/bfad_attr.c:908:8-16:
WARNING: use scnprintf or sprintf
./drivers/scsi/bfa/bfad_attr.c:860:8-16:
WARNING: use scnprintf or sprintf
./drivers/scsi/bfa/bfad_attr.c:888:8-16:
WARNING: use scnprintf or sprintf
./drivers/scsi/bfa/bfad_attr.c:853:8-16:
WARNING: use scnprintf or sprintf
./drivers/scsi/bfa/bfad_attr.c:808:8-16:
WARNING: use scnprintf or sprintf
./drivers/scsi/bfa/bfad_attr.c:728:8-16:
WARNING: use scnprintf or sprintf
./drivers/scsi/bfa/bfad_attr.c:822:8-16:
WARNING: use scnprintf or sprintf
./drivers/scsi/bfa/bfad_attr.c:927:9-17:
WARNING: use scnprintf or sprintf
./drivers/scsi/bfa/bfad_attr.c:900:8-16:
WARNING: use scnprintf or sprintf
./drivers/scsi/bfa/bfad_attr.c:874:8-16:
WARNING: use scnprintf or sprintf
./drivers/scsi/bfa/bfad_attr.c:714:8-16:
WARNING: use scnprintf or sprintf
./drivers/scsi/bfa/bfad_attr.c:839:8-16:
WARNING: use scnprintf or sprintf

Use sysfs_emit() instead of scnprintf() or sprintf().

---
 drivers/scsi/bfa/bfad_attr.c | 26 +++++++++++++-------------
 1 file changed, 13 insertions(+), 13 deletions(-)
drivers/scsi/bfa/bfad_attr.c +13 -13
index 0a70d54a4df6..47e599352468 100644
@@ -722,7 +722,7 @@ bfad_im_serial_num_show(struct device *dev, struct device_attribute *attr,
 	char serial_num[BFA_ADAPTER_SERIAL_NUM_LEN];
 
 	bfa_get_adapter_serial_num(&bfad->bfa, serial_num);
-	return snprintf(buf, PAGE_SIZE, "%s\n", serial_num);
+	return sysfs_emit(buf, "%s\n", serial_num);
 }
 
 static ssize_t
@@ -736,7 +736,7 @@ bfad_im_model_show(struct device *dev, struct device_attribute *attr,
 	char model[BFA_ADAPTER_MODEL_NAME_LEN];
 
 	bfa_get_adapter_model(&bfad->bfa, model);
-	return snprintf(buf, PAGE_SIZE, "%s\n", model);
+	return sysfs_emit(buf, "%s\n", model);
 }
 
 static ssize_t
@@ -816,7 +816,7 @@ bfad_im_model_desc_show(struct device *dev, struct device_attribute *attr,
 		snprintf(model_descr, BFA_ADAPTER_MODEL_DESCR_LEN,
 			"Invalid Model");
 
-	return snprintf(buf, PAGE_SIZE, "%s\n", model_descr);
+	return sysfs_emit(buf, "%s\n", model_descr);
 }
 
 static ssize_t
@@ -830,7 +830,7 @@ bfad_im_node_name_show(struct device *dev, struct device_attribute *attr,
 	u64        nwwn;
 
 	nwwn = bfa_fcs_lport_get_nwwn(port->fcs_port);
-	return snprintf(buf, PAGE_SIZE, "0x%llx\n", cpu_to_be64(nwwn));
+	return sysfs_emit(buf, "0x%llx\n", cpu_to_be64(nwwn));
 }
 
 static ssize_t
@@ -847,7 +847,7 @@ bfad_im_symbolic_name_show(struct device *dev, struct device_attribute *attr,
 	bfa_fcs_lport_get_attr(&bfad->bfa_fcs.fabric.bport, &port_attr);
 	strlcpy(symname, port_attr.port_cfg.sym_name.symname,
 			BFA_SYMNAME_MAXLEN);
-	return snprintf(buf, PAGE_SIZE, "%s\n", symname);
+	return sysfs_emit(buf, "%s\n", symname);
 }
 
 static ssize_t
@@ -861,14 +861,14 @@ bfad_im_hw_version_show(struct device *dev, struct device_attribute *attr,
 	char hw_ver[BFA_VERSION_LEN];
 
 	bfa_get_pci_chip_rev(&bfad->bfa, hw_ver);
-	return snprintf(buf, PAGE_SIZE, "%s\n", hw_ver);
+	return sysfs_emit(buf, "%s\n", hw_ver);
 }
 
 static ssize_t
 bfad_im_drv_version_show(struct device *dev, struct device_attribute *attr,
 				char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%s\n", BFAD_DRIVER_VERSION);
+	return sysfs_emit(buf, "%s\n", BFAD_DRIVER_VERSION);
 }
 
 static ssize_t
@@ -882,7 +882,7 @@ bfad_im_optionrom_version_show(struct device *dev,
 	char optrom_ver[BFA_VERSION_LEN];
 
 	bfa_get_adapter_optrom_ver(&bfad->bfa, optrom_ver);
-	return snprintf(buf, PAGE_SIZE, "%s\n", optrom_ver);
+	return sysfs_emit(buf, "%s\n", optrom_ver);
 }
 
 static ssize_t
@@ -896,7 +896,7 @@ bfad_im_fw_version_show(struct device *dev, struct device_attribute *attr,
 	char fw_ver[BFA_VERSION_LEN];
 
 	bfa_get_adapter_fw_ver(&bfad->bfa, fw_ver);
-	return snprintf(buf, PAGE_SIZE, "%s\n", fw_ver);
+	return sysfs_emit(buf, "%s\n", fw_ver);
 }
 
 static ssize_t
@@ -908,7 +908,7 @@ bfad_im_num_of_ports_show(struct device *dev, struct device_attribute *attr,
 			(struct bfad_im_port_s *) shost->hostdata[0];
 	struct bfad_s *bfad = im_port->bfad;
 
-	return snprintf(buf, PAGE_SIZE, "%d\n",
+	return sysfs_emit(buf, "%d\n",
 			bfa_get_nports(&bfad->bfa));
 }
 
@@ -916,7 +916,7 @@ static ssize_t
 bfad_im_drv_name_show(struct device *dev, struct device_attribute *attr,
 				char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%s\n", BFAD_DRIVER_NAME);
+	return sysfs_emit(buf, "%s\n", BFAD_DRIVER_NAME);
 }
 
 static ssize_t
@@ -935,14 +935,14 @@ bfad_im_num_of_discovered_ports_show(struct device *dev,
 	rports = kzalloc(sizeof(struct bfa_rport_qualifier_s) * nrports,
 			 GFP_ATOMIC);
 	if (rports == NULL)
-		return snprintf(buf, PAGE_SIZE, "Failed\n");
+		return sysfs_emit(buf, "Failed\n");
 
 	spin_lock_irqsave(&bfad->bfad_lock, flags);
 	bfa_fcs_lport_get_rport_quals(port->fcs_port, rports, &nrports);
 	spin_unlock_irqrestore(&bfad->bfad_lock, flags);
 	kfree(rports);
 
-	return snprintf(buf, PAGE_SIZE, "%d\n", nrports);
+	return sysfs_emit(buf, "%d\n", nrports);
 }
 
 static          DEVICE_ATTR(serial_number, S_IRUGO,
Signature · 1 line
2.34.1
author maintainer
#5 lore raw

PATCH 6/22 power: supply: axp20x_battery: properly report current when discharging

In reply to Sasha Levin

From: Evgeny Boger <[email protected]>

[ Upstream commit d4f408cdcd26921c1268cb8dcbe8ffb6faf837f3 ]

As stated in [1], negative current values are used for discharging batteries.

AXP PMICs internally have two different ADC channels for shunt current
measurement: one used during charging and one during discharging. The values reported by these ADCs are unsigned.
While the driver properly selects ADC channel to get the data from, it doesn't apply negative sign when reporting discharging current.

[1] Documentation/ABI/testing/sysfs-class-power

---
 drivers/power/supply/axp20x_battery.c | 13 ++++++-------
 1 file changed, 6 insertions(+), 7 deletions(-)
drivers/power/supply/axp20x_battery.c +6 -7
index 7494f0f0eadb..a2e2443357fa 100644
@@ -160,7 +160,6 @@ static int axp20x_battery_get_prop(struct power_supply *psy,
 				   union power_supply_propval *val)
 {
 	struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy);
-	struct iio_channel *chan;
 	int ret = 0, reg, val1;
 
 	switch (psp) {
@@ -240,12 +239,12 @@ static int axp20x_battery_get_prop(struct power_supply *psy,
 		if (ret)
 			return ret;
 
-		if (reg & AXP20X_PWR_STATUS_BAT_CHARGING)
-			chan = axp20x_batt->batt_chrg_i;
-		else
-			chan = axp20x_batt->batt_dischrg_i;
-
-		ret = iio_read_channel_processed(chan, &val->intval);
+		if (reg & AXP20X_PWR_STATUS_BAT_CHARGING) {
+			ret = iio_read_channel_processed(axp20x_batt->batt_chrg_i, &val->intval);
+		} else {
+			ret = iio_read_channel_processed(axp20x_batt->batt_dischrg_i, &val1);
+			val->intval = -val1;
+		}
 		if (ret)
 			return ret;
 
Signature · 1 line
2.34.1
author maintainer
#6 lore raw

PATCH 7/22 powerpc: Set crashkernel offset to mid of RMA region

In reply to Sasha Levin

From: Sourabh Jain <[email protected]>

[ Upstream commit 7c5ed82b800d8615cdda00729e7b62e5899f0b13 ]

On large config LPARs (having 192 and more cores), Linux fails to boot due to insufficient memory in the first memblock. It is due to the memory reservation for the crash kernel which starts at 128MB offset of the first memblock. This memory reservation for the crash kernel doesn't leave enough space in the first memblock to accommodate other essential system resources.

The crash kernel start address was set to 128MB offset by default to ensure that the crash kernel get some memory below the RMA region which is used to be of size 256MB. But given that the RMA region size can be 512MB or more, setting the crash kernel offset to mid of RMA size will leave enough space for the kernel to allocate memory for other system resources.

Since the above crash kernel offset change is only applicable to the LPAR platform, the LPAR feature detection is pushed before the crash kernel reservation. The rest of LPAR specific initialization will still be done during pseries_probe_fw_features as usual.

This patch is dependent on changes to paca allocation for boot CPU. It expect boot CPU to discover 1T segment support which is introduced by the patch posted here:
https://lists.ozlabs.org/pipermail/linuxppc-dev/2022-January/239175.html

---
 arch/powerpc/kernel/machine_kexec.c | 15 +++++++++++----
 arch/powerpc/kernel/rtas.c          |  6 ++++++
 2 files changed, 17 insertions(+), 4 deletions(-)
arch/powerpc/kernel/machine_kexec.c +11 -4
index cb4d6cd949fc..101b0fb7a80e 100644
@@ -145,11 +145,18 @@ void __init reserve_crashkernel(void)
 	if (!crashk_res.start) {
 #ifdef CONFIG_PPC64
 		/*
-		 * On 64bit we split the RMO in half but cap it at half of
-		 * a small SLB (128MB) since the crash kernel needs to place
-		 * itself and some stacks to be in the first segment.
+		 * On the LPAR platform place the crash kernel to mid of
+		 * RMA size (512MB or more) to ensure the crash kernel
+		 * gets enough space to place itself and some stack to be
+		 * in the first segment. At the same time normal kernel
+		 * also get enough space to allocate memory for essential
+		 * system resource in the first segment. Keep the crash
+		 * kernel starts at 128MB offset on other platforms.
 		 */
-		crashk_res.start = min(0x8000000ULL, (ppc64_rma_size / 2));
+		if (firmware_has_feature(FW_FEATURE_LPAR))
+			crashk_res.start = ppc64_rma_size / 2;
+		else
+			crashk_res.start = min(0x8000000ULL, (ppc64_rma_size / 2));
 #else
 		crashk_res.start = KDUMP_KERNELBASE;
 #endif
arch/powerpc/kernel/rtas.c +6 -0
index 55b266d7afe1..912e7f69266e 100644
@@ -1356,6 +1356,12 @@ int __init early_init_dt_scan_rtas(unsigned long node,
 	entryp = of_get_flat_dt_prop(node, "linux,rtas-entry", NULL);
 	sizep  = of_get_flat_dt_prop(node, "rtas-size", NULL);
 
+#ifdef CONFIG_PPC64
+	/* need this feature to decide the crashkernel offset */
+	if (of_get_flat_dt_prop(node, "ibm,hypertas-functions", NULL))
+		powerpc_firmware_features |= FW_FEATURE_LPAR;
+#endif
+
 	if (basep && entryp && sizep) {
 		rtas.base = *basep;
 		rtas.entry = *entryp;
Signature · 1 line
2.34.1
author maintainer
#7 lore raw

PATCH 8/22 PCI: aardvark: Fix support for MSI interrupts

In reply to Sasha Levin

From: Pali Rohár <[email protected]>

[ Upstream commit b0b0b8b897f8e12b2368e868bd7cdc5742d5c5a9 ]

Aardvark hardware supports Multi-MSI and MSI_FLAG_MULTI_PCI_MSI is already set for the MSI chip. But when allocating MSI interrupt numbers for Multi-MSI, the numbers need to be properly aligned, otherwise endpoint devices send MSI interrupt with incorrect numbers.

Fix this issue by using function bitmap_find_free_region() instead of bitmap_find_next_zero_area().

To ensure that aligned MSI interrupt numbers are used by endpoint devices, we cannot use Linux virtual irq numbers (as they are random and not properly aligned). Instead we need to use the aligned hwirq numbers.

This change fixes receiving MSI interrupts on Armada 3720 boards and allows using NVMe disks which use Multi-MSI feature with 3 interrupts.

Without this NVMe disks freeze booting as linux nvme-core.c is waiting 60s for an interrupt.

---
 drivers/pci/host/pci-aardvark.c | 16 ++++++----------
 1 file changed, 6 insertions(+), 10 deletions(-)
drivers/pci/host/pci-aardvark.c +6 -10
index 9ae544e113dc..124fd7cb5da5 100644
@@ -834,7 +834,7 @@ static void advk_msi_irq_compose_msi_msg(struct irq_data *data,
 
 	msg->address_lo = lower_32_bits(msi_msg);
 	msg->address_hi = upper_32_bits(msi_msg);
-	msg->data = data->irq;
+	msg->data = data->hwirq;
 }
 
 static int advk_msi_set_affinity(struct irq_data *irq_data,
@@ -851,15 +851,11 @@ static int advk_msi_irq_domain_alloc(struct irq_domain *domain,
 	int hwirq, i;
 
 	mutex_lock(&pcie->msi_used_lock);
-	hwirq = bitmap_find_next_zero_area(pcie->msi_used, MSI_IRQ_NUM,
-					   0, nr_irqs, 0);
-	if (hwirq >= MSI_IRQ_NUM) {
-		mutex_unlock(&pcie->msi_used_lock);
-		return -ENOSPC;
-	}
-
-	bitmap_set(pcie->msi_used, hwirq, nr_irqs);
+	hwirq = bitmap_find_free_region(pcie->msi_used, MSI_IRQ_NUM,
+					order_base_2(nr_irqs));
 	mutex_unlock(&pcie->msi_used_lock);
+	if (hwirq < 0)
+		return -ENOSPC;
 
 	for (i = 0; i < nr_irqs; i++)
 		irq_domain_set_info(domain, virq + i, hwirq + i,
@@ -877,7 +873,7 @@ static void advk_msi_irq_domain_free(struct irq_domain *domain,
 	struct advk_pcie *pcie = domain->host_data;
 
 	mutex_lock(&pcie->msi_used_lock);
-	bitmap_clear(pcie->msi_used, d->hwirq, nr_irqs);
+	bitmap_release_region(pcie->msi_used, d->hwirq, order_base_2(nr_irqs));
 	mutex_unlock(&pcie->msi_used_lock);
 }
 
Signature · 1 line
2.34.1
author maintainer
#8 lore raw

PATCH 9/22 iommu/arm-smmu-v3: fix event handling soft lockup

In reply to Sasha Levin

From: Zhou Guanghui <[email protected]>

[ Upstream commit 30de2b541af98179780054836b48825fcfba4408 ]

During event processing, events are read from the event queue one by one until the queue is empty.If the master device continuously requests address access at the same time and the SMMU generates events, the cyclic processing of the event takes a long time and softlockup warnings may be reported.

arm-smmu-v3 arm-smmu-v3.34.auto: event 0x0a received:
arm-smmu-v3 arm-smmu-v3.34.auto: 0x00007f220000280a
arm-smmu-v3 arm-smmu-v3.34.auto: 0x000010000000007e
arm-smmu-v3 arm-smmu-v3.34.auto: 0x00000000034e8670

watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [irq/268-arm-smm:247]
Call trace:
 _dev_info+0x7c/0xa0
 arm_smmu_evtq_thread+0x1c0/0x230
 irq_thread_fn+0x30/0x80
 irq_thread+0x128/0x210
 kthread+0x134/0x138
 ret_from_fork+0x10/0x1c
Kernel panic - not syncing: softlockup: hung tasks

Fix this by calling cond_resched() after the event information is printed.

---
 drivers/iommu/arm-smmu-v3.c | 1 +
 1 file changed, 1 insertion(+)
drivers/iommu/arm-smmu-v3.c +1 -0
index 29feafa8007f..878087b9ddfe 100644
@@ -1210,6 +1210,7 @@ static irqreturn_t arm_smmu_evtq_thread(int irq, void *dev)
 				dev_info(smmu->dev, "\t0x%016llx\n",
 					 (unsigned long long)evt[i]);
 
+			cond_resched();
 		}
 
 		/*
Signature · 6 lines
2.34.1

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#10 lore raw

PATCH 11/22 scsi: pm8001: Fix pm8001_mpi_task_abort_resp()

In reply to Sasha Levin

From: Damien Le Moal <[email protected]>

[ Upstream commit 7e6b7e740addcea450041b5be8e42f0a4ceece0f ]

The call to pm8001_ccb_task_free() at the end of pm8001_mpi_task_abort_resp() already frees the ccb tag. So when the device NCQ_ABORT_ALL_FLAG is set, the tag should not be freed again. Also change the hardcoded 0xBFFFFFFF value to ~NCQ_ABORT_ALL_FLAG as it ought to be.

---
 drivers/scsi/pm8001/pm8001_hwi.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)
drivers/scsi/pm8001/pm8001_hwi.c +3 -4
index f374abfb7f1f..f5c7fffec081 100644
@@ -3766,12 +3766,11 @@ int pm8001_mpi_task_abort_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
 	mb();
 
 	if (pm8001_dev->id & NCQ_ABORT_ALL_FLAG) {
-		pm8001_tag_free(pm8001_ha, tag);
 		sas_free_task(t);
-		/* clear the flag */
-		pm8001_dev->id &= 0xBFFFFFFF;
-	} else
+		pm8001_dev->id &= ~NCQ_ABORT_ALL_FLAG;
+	} else {
 		t->task_done(t);
+	}
 
 	return 0;
 }
Signature · 1 line
2.34.1
author maintainer
#11 lore raw

PATCH 12/22 scsi: aha152x: Fix aha152x_setup() __setup handler return value

In reply to Sasha Levin

From: Randy Dunlap <[email protected]>

[ Upstream commit cc8294ec4738d25e2bb2d71f7d82a9bf7f4a157b ]

__setup() handlers should return 1 if the command line option is handled and 0 if not (or maybe never return 0; doing so just pollutes init's environment with strings that are not init arguments/parameters).

Return 1 from aha152x_setup() to indicate that the boot option has been handled.

---
 drivers/scsi/aha152x.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/scsi/aha152x.c +2 -4
index bc0058df31c6..24ef8e326ee5 100644
@@ -3374,13 +3374,11 @@ static int __init aha152x_setup(char *str)
 	setup[setup_count].synchronous = ints[0] >= 6 ? ints[6] : 1;
 	setup[setup_count].delay       = ints[0] >= 7 ? ints[7] : DELAY_DEFAULT;
 	setup[setup_count].ext_trans   = ints[0] >= 8 ? ints[8] : 0;
-	if (ints[0] > 8) {                                                /*}*/
+	if (ints[0] > 8)
 		printk(KERN_NOTICE "aha152x: usage: aha152x=<IOBASE>[,<IRQ>[,<SCSI ID>"
 		       "[,<RECONNECT>[,<PARITY>[,<SYNCHRONOUS>[,<DELAY>[,<EXT_TRANS>]]]]]]]\n");
-	} else {
+	else
 		setup_count++;
-		return 0;
-	}
 
 	return 1;
 }
Signature · 1 line
2.34.1
author maintainer
#12 lore raw

PATCH 13/22 net/smc: correct settings of RMB window update limit

In reply to Sasha Levin

From: Dust Li <[email protected]>

[ Upstream commit 6bf536eb5c8ca011d1ff57b5c5f7c57ceac06a37 ]

rmbe_update_limit is used to limit announcing receive window updating too frequently. RFC7609 request a minimal increase in the window size of 10% of the receive buffer space. But current implementation used:

min_t(int, rmbe_size / 10, SOCK_MIN_SNDBUF / 2)

and SOCK_MIN_SNDBUF / 2 == 2304 Bytes, which is almost always less then 10% of the receive buffer space.

This causes the receiver always sending CDC message to update its consumer cursor when it consumes more then 2K of data. And as a result, we may encounter something like "TCP silly window syndrome" when sending 2.5~8K message.

This patch fixes this using max(rmbe_size / 10, SOCK_MIN_SNDBUF / 2).

With this patch and SMC autocorking enabled, qperf 2K/4K/8K tcp_bw test shows 45%/75%/40% increase in throughput respectively.

---
 net/smc/smc_core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/smc/smc_core.c +1 -1
index 7dc907a45c68..a28e06c70e52 100644
@@ -499,7 +499,7 @@ struct smc_buf_desc *smc_buf_get_slot(struct smc_link_group *lgr,
  */
 static inline int smc_rmb_wnd_update_limit(int rmbe_size)
 {
-	return min_t(int, rmbe_size / 10, SOCK_MIN_SNDBUF / 2);
+	return max_t(int, rmbe_size / 10, SOCK_MIN_SNDBUF / 2);
 }
 
 static struct smc_buf_desc *smc_new_buf_create(struct smc_link_group *lgr,
Signature · 1 line
2.34.1
author maintainer
#13 lore raw

PATCH 14/22 macvtap: advertise link netns via netlink

In reply to Sasha Levin

From: Sven Eckelmann <[email protected]>

[ Upstream commit a02192151b7dbf855084c38dca380d77c7658353 ]

Assign rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is added to rtnetlink messages. This fixes iproute2 which otherwise resolved the link interface to an interface in the wrong namespace.

Test commands:

ip netns add nst
ip link add dummy0 type dummy
ip link add link macvtap0 link dummy0 type macvtap ip link set macvtap0 netns nst
ip -netns nst link show macvtap0

Before:

10: macvtap0@gre0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 500

      link/ether 5e:8f:ae:1d:60:50 brd ff:ff:ff:ff:ff:ff

After:

10: macvtap0@if2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 500

      link/ether 5e:8f:ae:1d:60:50 brd ff:ff:ff:ff:ff:ff link-netnsid 0
---
 drivers/net/macvtap.c | 6 ++++++
 1 file changed, 6 insertions(+)
drivers/net/macvtap.c +6 -0
index cba5cb3b849a..dc89019ca876 100644
@@ -132,11 +132,17 @@ static void macvtap_setup(struct net_device *dev)
 	dev->tx_queue_len = TUN_READQ_SIZE;
 }
 
+static struct net *macvtap_link_net(const struct net_device *dev)
+{
+	return dev_net(macvlan_dev_real_dev(dev));
+}
+
 static struct rtnl_link_ops macvtap_link_ops __read_mostly = {
 	.kind		= "macvtap",
 	.setup		= macvtap_setup,
 	.newlink	= macvtap_newlink,
 	.dellink	= macvtap_dellink,
+	.get_link_net	= macvtap_link_net,
 	.priv_size      = sizeof(struct macvtap_dev),
 };
 
Signature · 1 line
2.34.1
author maintainer
#14 lore raw

PATCH 15/22 bnxt_en: Eliminate unintended link toggle during FW reset

In reply to Sasha Levin

From: Michael Chan <[email protected]>

[ Upstream commit 7c492a2530c1f05441da541307c2534230dfd59b ]

If the flow control settings have been changed, a subsequent FW reset may cause the ethernet link to toggle unnecessarily. This link toggle will increase the down time by a few seconds.

The problem is caused by bnxt_update_phy_setting() detecting a false mismatch in the flow control settings between the stored software settings and the current FW settings after the FW reset. This mismatch is caused by the AUTONEG bit added to link_info->req_flow_ctrl in an inconsistent way in bnxt_set_pauseparam() in autoneg mode. The AUTONEG bit should not be added to link_info->req_flow_ctrl.

---
 drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c +1 -3
index e3123cb0fb70..82e16b2d1f7a 100644
@@ -1272,9 +1272,7 @@ static int bnxt_set_pauseparam(struct net_device *dev,
 		}
 
 		link_info->autoneg |= BNXT_AUTONEG_FLOW_CTRL;
-		if (bp->hwrm_spec_code >= 0x10201)
-			link_info->req_flow_ctrl =
-				PORT_PHY_CFG_REQ_AUTO_PAUSE_AUTONEG_PAUSE;
+		link_info->req_flow_ctrl = 0;
 	} else {
 		/* when transition from auto pause to force pause,
 		 * force a link change
Signature · 1 line
2.34.1
author maintainer
#15 lore raw

PATCH 16/22 MIPS: fix fortify panic when copying asm exception handlers

In reply to Sasha Levin

From: Alexander Lobakin <[email protected]>

[ Upstream commit d17b66417308996e7e64b270a3c7f3c1fbd4cfc8 ]

With KCFLAGS="-O3", I was able to trigger a fortify-source memcpy() overflow panic on set_vi_srs_handler(). Although O3 level is not supported in the mainline, under some conditions that may've happened with any optimization settings, it's just a matter of inlining luck. The panic itself is correct, more precisely, 50/50 false-positive and not at the same time. From the one side, no real overflow happens. Exception handler defined in asm just gets copied to some reserved places in the memory.
But the reason behind is that C code refers to that exception handler declares it as char, i.e. something of 1 byte length. It's obvious that the asm function itself is way more than 1 byte, so fortify logics thought we are going to past the symbol declared. The standard way to refer to asm symbols from C code which is not supposed to be called from C is to declare them as extern const u8[]. This is fully correct from any point of view, as any code itself is just a bunch of bytes (including 0 as it is for syms like _stext/_etext/etc.), and the exact size is not known at the moment of compilation.
Adjust the type of the except_vec_vi_*() and related variables. Make set_handler() take const as a second argument to avoid cast-away warnings and give a little more room for optimization.

---
 arch/mips/include/asm/setup.h |  2 +-
 arch/mips/kernel/traps.c      | 22 +++++++++++-----------
 2 files changed, 12 insertions(+), 12 deletions(-)
arch/mips/include/asm/setup.h +1 -1
index d49d247d48a1..d48a5f18a267 100644
@@ -14,7 +14,7 @@ static inline void setup_8250_early_printk_port(unsigned long base,
 	unsigned int reg_shift, unsigned int timeout) {}
 #endif
 
-extern void set_handler(unsigned long offset, void *addr, unsigned long len);
+void set_handler(unsigned long offset, const void *addr, unsigned long len);
 extern void set_uncached_handler(unsigned long offset, void *addr, unsigned long len);
 
 typedef void (*vi_handler_t)(void);
arch/mips/kernel/traps.c +11 -11
index 4a23d89e251c..abbc64788008 100644
@@ -2017,19 +2017,19 @@ static void *set_vi_srs_handler(int n, vi_handler_t addr, int srs)
 		 * If no shadow set is selected then use the default handler
 		 * that does normal register saving and standard interrupt exit
 		 */
-		extern char except_vec_vi, except_vec_vi_lui;
-		extern char except_vec_vi_ori, except_vec_vi_end;
-		extern char rollback_except_vec_vi;
-		char *vec_start = using_rollback_handler() ?
-			&rollback_except_vec_vi : &except_vec_vi;
+		extern const u8 except_vec_vi[], except_vec_vi_lui[];
+		extern const u8 except_vec_vi_ori[], except_vec_vi_end[];
+		extern const u8 rollback_except_vec_vi[];
+		const u8 *vec_start = using_rollback_handler() ?
+				      rollback_except_vec_vi : except_vec_vi;
 #if defined(CONFIG_CPU_MICROMIPS) || defined(CONFIG_CPU_BIG_ENDIAN)
-		const int lui_offset = &except_vec_vi_lui - vec_start + 2;
-		const int ori_offset = &except_vec_vi_ori - vec_start + 2;
+		const int lui_offset = except_vec_vi_lui - vec_start + 2;
+		const int ori_offset = except_vec_vi_ori - vec_start + 2;
 #else
-		const int lui_offset = &except_vec_vi_lui - vec_start;
-		const int ori_offset = &except_vec_vi_ori - vec_start;
+		const int lui_offset = except_vec_vi_lui - vec_start;
+		const int ori_offset = except_vec_vi_ori - vec_start;
 #endif
-		const int handler_len = &except_vec_vi_end - vec_start;
+		const int handler_len = except_vec_vi_end - vec_start;
 
 		if (handler_len > VECTORSPACING) {
 			/*
@@ -2249,7 +2249,7 @@ void per_cpu_trap_init(bool is_boot_cpu)
 }
 
 /* Install CPU exception handler */
-void set_handler(unsigned long offset, void *addr, unsigned long size)
+void set_handler(unsigned long offset, const void *addr, unsigned long size)
 {
 #ifdef CONFIG_CPU_MICROMIPS
 	memcpy((void *)(ebase + offset), ((unsigned char *)addr - 1), size);
Signature · 1 line
2.34.1
author maintainer
#16 lore raw

PATCH 17/22 powerpc/code-patching: Pre-map patch area

In reply to Sasha Levin

From: Michael Ellerman <[email protected]>

[ Upstream commit 591b4b268435f00d2f0b81f786c2c7bd5ef66416 ]

Paul reported a warning with DEBUG_ATOMIC_SLEEP=y:

  BUG: sleeping function called from invalid context at include/linux/sched/mm.h:256
  in_atomic(): 0, irqs_disabled(): 1, non_block: 0, pid: 1, name: swapper/0
  preempt_count: 0, expected: 0
  ...
  Call Trace:
    dump_stack_lvl+0xa0/0xec (unreliable)
    __might_resched+0x2f4/0x310
    kmem_cache_alloc+0x220/0x4b0
    __pud_alloc+0x74/0x1d0
    hash__map_kernel_page+0x2cc/0x390
    do_patch_instruction+0x134/0x4a0
    arch_jump_label_transform+0x64/0x78
    __jump_label_update+0x148/0x180
    static_key_enable_cpuslocked+0xd0/0x120
    static_key_enable+0x30/0x50
    check_kvm_guest+0x60/0x88
    pSeries_smp_probe+0x54/0xb0
    smp_prepare_cpus+0x3e0/0x430
    kernel_init_freeable+0x20c/0x43c
    kernel_init+0x30/0x1a0
    ret_from_kernel_thread+0x5c/0x64

Peter pointed out that this is because do_patch_instruction() has disabled interrupts, but then map_patch_area() calls map_kernel_page() then hash__map_kernel_page() which does a sleeping memory allocation.

We only see the warning in KVM guests with SMT enabled, which is not particularly common, or on other platforms if CONFIG_KPROBES is disabled, also not common. The reason we don't see it in most configurations is that another path that happens to have interrupts enabled has allocated the required page tables for us, eg. there's a path in kprobes init that does that. That's just pure luck though.

As Christophe suggested, the simplest solution is to do a dummy map/unmap when we initialise the patching, so that any required page table levels are pre-allocated before the first call to do_patch_instruction(). This works because the unmap doesn't free any page tables that were allocated by the map, it just clears the PTE, leaving the page table levels there for the next map.

---
 arch/powerpc/lib/code-patching.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
arch/powerpc/lib/code-patching.c +14 -0
index 85f84b45d3a0..c58a619a68b3 100644
@@ -47,9 +47,14 @@ int raw_patch_instruction(unsigned int *addr, unsigned int instr)
 #ifdef CONFIG_STRICT_KERNEL_RWX
 static DEFINE_PER_CPU(struct vm_struct *, text_poke_area);
 
+static int map_patch_area(void *addr, unsigned long text_poke_addr);
+static void unmap_patch_area(unsigned long addr);
+
 static int text_area_cpu_up(unsigned int cpu)
 {
 	struct vm_struct *area;
+	unsigned long addr;
+	int err;
 
 	area = get_vm_area(PAGE_SIZE, VM_ALLOC);
 	if (!area) {
@@ -57,6 +62,15 @@ static int text_area_cpu_up(unsigned int cpu)
 			cpu);
 		return -1;
 	}
+
+	// Map/unmap the area to ensure all page tables are pre-allocated
+	addr = (unsigned long)area->addr;
+	err = map_patch_area(empty_zero_page, addr);
+	if (err)
+		return err;
+
+	unmap_patch_area(addr);
+
 	this_cpu_write(text_poke_area, area);
 
 	return 0;
Signature · 1 line
2.34.1
author maintainer
#17 lore raw

PATCH 18/22 scsi: libfc: Fix use after free in fc_exch_abts_resp()

In reply to Sasha Levin

From: Jianglei Nie <[email protected]>

[ Upstream commit 271add11994ba1a334859069367e04d2be2ebdd4 ]

fc_exch_release(ep) will decrease the ep's reference count. When the reference count reaches zero, it is freed. But ep is still used in the following code, which will lead to a use after free.

Return after the fc_exch_release() call to avoid use after free.

---
 drivers/scsi/libfc/fc_exch.c | 1 +
 1 file changed, 1 insertion(+)
drivers/scsi/libfc/fc_exch.c +1 -0
index 384458d1f73c..9fa0aa235cb4 100644
@@ -1709,6 +1709,7 @@ static void fc_exch_abts_resp(struct fc_exch *ep, struct fc_frame *fp)
 	if (cancel_delayed_work_sync(&ep->timeout_work)) {
 		FC_EXCH_DBG(ep, "Exchange timer canceled due to ABTS response\n");
 		fc_exch_release(ep);	/* release from pending timer hold */
+		return;
 	}
 
 	spin_lock_bh(&ep->ex_lock);
Signature · 1 line
2.34.1
author maintainer
#18 lore raw

PATCH 19/22 usb: dwc3: omap: fix "unbalanced disables for smps10_out1" on omap5evm

In reply to Sasha Levin

From: "H. Nikolaus Schaller" <[email protected]>

[ Upstream commit ac01df343e5a6c6bcead2ed421af1fde30f73e7e ]

Usually, the vbus_regulator (smps10 on omap5evm) boots up disabled.

Hence calling regulator_disable() indirectly through dwc3_omap_set_mailbox() during probe leads to:

[   10.332764] WARNING: CPU: 0 PID: 1628 at drivers/regulator/core.c:2853 _regulator_disable+0x40/0x164
[   10.351919] unbalanced disables for smps10_out1
[   10.361298] Modules linked in: dwc3_omap(+) clk_twl6040 at24 gpio_twl6040 palmas_gpadc palmas_pwrbutton
industrialio snd_soc_omap_mcbsp(+) snd_soc_ti_sdma display_connector ti_tpd12s015 drm leds_gpio
drm_panel_orientation_quirks ip_tables x_tables ipv6 autofs4
[   10.387818] CPU: 0 PID: 1628 Comm: systemd-udevd Not tainted 5.17.0-rc1-letux-lpae+ #8139
[   10.405129] Hardware name: Generic OMAP5 (Flattened Device Tree)
[   10.411455]  unwind_backtrace from show_stack+0x10/0x14
[   10.416970]  show_stack from dump_stack_lvl+0x40/0x4c
[   10.422313]  dump_stack_lvl from __warn+0xb8/0x170
[   10.427377]  __warn from warn_slowpath_fmt+0x70/0x9c
[   10.432595]  warn_slowpath_fmt from _regulator_disable+0x40/0x164
[   10.439037]  _regulator_disable from regulator_disable+0x30/0x64
[   10.445382]  regulator_disable from dwc3_omap_set_mailbox+0x8c/0xf0 [dwc3_omap]
[   10.453116]  dwc3_omap_set_mailbox [dwc3_omap] from dwc3_omap_probe+0x2b8/0x394 [dwc3_omap]
[   10.467021]  dwc3_omap_probe [dwc3_omap] from platform_probe+0x58/0xa8
[   10.481762]  platform_probe from really_probe+0x168/0x2fc
[   10.481782]  really_probe from __driver_probe_device+0xc4/0xd8
[   10.481782]  __driver_probe_device from driver_probe_device+0x24/0xa4
[   10.503762]  driver_probe_device from __driver_attach+0xc4/0xd8
[   10.510018]  __driver_attach from bus_for_each_dev+0x64/0xa0
[   10.516001]  bus_for_each_dev from bus_add_driver+0x148/0x1a4
[   10.524880]  bus_add_driver from driver_register+0xb4/0xf8
[   10.530678]  driver_register from do_one_initcall+0x90/0x1c4
[   10.536661]  do_one_initcall from do_init_module+0x4c/0x200
[   10.536683]  do_init_module from load_module+0x13dc/0x1910
[   10.551159]  load_module from sys_finit_module+0xc8/0xd8
[   10.561319]  sys_finit_module from __sys_trace_return+0x0/0x18
[   10.561336] Exception stack(0xc344bfa8 to 0xc344bff0)
[   10.561341] bfa0:                   b6fb5778 b6fab8d8 00000007 b6ecfbb8 00000000 b6ed0398
[   10.561341] bfc0: b6fb5778 b6fab8d8 855c0500 0000017b 00020000 b6f9a3cc 00000000 b6fb5778
[   10.595500] bfe0: bede18f8 bede18e8 b6ec9aeb b6dda1c2
[   10.601345] ---[ end trace 0000000000000000 ]---

Fix this unnecessary warning by checking if the regulator is enabled.

---
 drivers/usb/dwc3/dwc3-omap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/usb/dwc3/dwc3-omap.c +1 -1
index 830ef7333750..6fbaa0d1bcd2 100644
@@ -245,7 +245,7 @@ static void dwc3_omap_set_mailbox(struct dwc3_omap *omap,
 		break;
 
 	case OMAP_DWC3_ID_FLOAT:
-		if (omap->vbus_reg)
+		if (omap->vbus_reg && regulator_is_enabled(omap->vbus_reg))
 			regulator_disable(omap->vbus_reg);
 		val = dwc3_omap_read_utmi_ctrl(omap);
 		val |= USBOTGSS_UTMI_OTG_CTRL_IDDIG;
Signature · 1 line
2.34.1
author maintainer
#19 lore raw

PATCH 20/22 xtensa: fix DTC warning unit_address_format

In reply to Sasha Levin

From: Max Filippov <[email protected]>

[ Upstream commit e85d29ba4b24f68e7a78cb85c55e754362eeb2de ]

DTC issues the following warnings when building xtfpga device trees:

/soc/flash@00000000/partition@0x0: unit name should not have leading "0x" /soc/flash@00000000/partition@0x6000000: unit name should not have leading "0x" /soc/flash@00000000/partition@0x6800000: unit name should not have leading "0x" /soc/flash@00000000/partition@0x7fe0000: unit name should not have leading "0x"

Drop leading 0x from flash partition unit names.

---
 arch/xtensa/boot/dts/xtfpga-flash-128m.dtsi | 8 ++++----
 arch/xtensa/boot/dts/xtfpga-flash-16m.dtsi  | 8 ++++----
 arch/xtensa/boot/dts/xtfpga-flash-4m.dtsi   | 4 ++--
 3 files changed, 10 insertions(+), 10 deletions(-)
arch/xtensa/boot/dts/xtfpga-flash-128m.dtsi +4 -4
index 9bf8bad1dd18..c33932568aa7 100644
@@ -8,19 +8,19 @@ flash: flash@00000000 {
 			reg = <0x00000000 0x08000000>;
 			bank-width = <2>;
 			device-width = <2>;
-			partition@0x0 {
+			partition@0 {
 				label = "data";
 				reg = <0x00000000 0x06000000>;
 			};
-			partition@0x6000000 {
+			partition@6000000 {
 				label = "boot loader area";
 				reg = <0x06000000 0x00800000>;
 			};
-			partition@0x6800000 {
+			partition@6800000 {
 				label = "kernel image";
 				reg = <0x06800000 0x017e0000>;
 			};
-			partition@0x7fe0000 {
+			partition@7fe0000 {
 				label = "boot environment";
 				reg = <0x07fe0000 0x00020000>;
 			};
arch/xtensa/boot/dts/xtfpga-flash-16m.dtsi +4 -4
index 40c2f81f7cb6..7bde2ab2d6fb 100644
@@ -8,19 +8,19 @@ flash: flash@08000000 {
 			reg = <0x08000000 0x01000000>;
 			bank-width = <2>;
 			device-width = <2>;
-			partition@0x0 {
+			partition@0 {
 				label = "boot loader area";
 				reg = <0x00000000 0x00400000>;
 			};
-			partition@0x400000 {
+			partition@400000 {
 				label = "kernel image";
 				reg = <0x00400000 0x00600000>;
 			};
-			partition@0xa00000 {
+			partition@a00000 {
 				label = "data";
 				reg = <0x00a00000 0x005e0000>;
 			};
-			partition@0xfe0000 {
+			partition@fe0000 {
 				label = "boot environment";
 				reg = <0x00fe0000 0x00020000>;
 			};
arch/xtensa/boot/dts/xtfpga-flash-4m.dtsi +2 -2
index fb8d3a9f33c2..0655b868749a 100644
@@ -8,11 +8,11 @@ flash: flash@08000000 {
 			reg = <0x08000000 0x00400000>;
 			bank-width = <2>;
 			device-width = <2>;
-			partition@0x0 {
+			partition@0 {
 				label = "boot loader area";
 				reg = <0x00000000 0x003f0000>;
 			};
-			partition@0x3f0000 {
+			partition@3f0000 {
 				label = "boot environment";
 				reg = <0x003f0000 0x00010000>;
 			};
Signature · 1 line
2.34.1
author maintainer
#20 lore raw

PATCH 21/22 Bluetooth: Fix use after free in hci_send_acl

In reply to Sasha Levin

From: Luiz Augusto von Dentz <[email protected]>

[ Upstream commit f63d24baff787e13b723d86fe036f84bdbc35045 ]

This fixes the following trace caused by receiving HCI_EV_DISCONN_PHY_LINK_COMPLETE which does call hci_conn_del without first checking if conn->type is in fact AMP_LINK and in case it is do properly cleanup upper layers with hci_disconn_cfm:

==================================================================

    BUG: KASAN: use-after-free in hci_send_acl+0xaba/0xc50
    Read of size 8 at addr ffff88800e404818 by task bluetoothd/142

    CPU: 0 PID: 142 Comm: bluetoothd Not tainted
    5.17.0-rc5-00006-gda4022eeac1a #7
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
    rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
    Call Trace:
     <TASK>
     dump_stack_lvl+0x45/0x59
     print_address_description.constprop.0+0x1f/0x150
     kasan_report.cold+0x7f/0x11b
     hci_send_acl+0xaba/0xc50
     l2cap_do_send+0x23f/0x3d0
     l2cap_chan_send+0xc06/0x2cc0
     l2cap_sock_sendmsg+0x201/0x2b0
     sock_sendmsg+0xdc/0x110
     sock_write_iter+0x20f/0x370
     do_iter_readv_writev+0x343/0x690
     do_iter_write+0x132/0x640
     vfs_writev+0x198/0x570
     do_writev+0x202/0x280
     do_syscall_64+0x38/0x90
     entry_SYSCALL_64_after_hwframe+0x44/0xae
    RSP: 002b:00007ffce8a099b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000014
    Code: 0f 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3
    0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 14 00 00 00 0f 05
    <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10
    RDX: 0000000000000001 RSI: 00007ffce8a099e0 RDI: 0000000000000015
    RAX: ffffffffffffffda RBX: 00007ffce8a099e0 RCX: 00007f788fc3cf77
    R10: 00007ffce8af7080 R11: 0000000000000246 R12: 000055e4ccf75580
    RBP: 0000000000000015 R08: 0000000000000002 R09: 0000000000000001
    </TASK>
    R13: 000055e4ccf754a0 R14: 000055e4ccf75cd0 R15: 000055e4ccf4a6b0

    Allocated by task 45:
        kasan_save_stack+0x1e/0x40
        __kasan_kmalloc+0x81/0xa0
        hci_chan_create+0x9a/0x2f0
        l2cap_conn_add.part.0+0x1a/0xdc0
        l2cap_connect_cfm+0x236/0x1000
        le_conn_complete_evt+0x15a7/0x1db0
        hci_le_conn_complete_evt+0x226/0x2c0
        hci_le_meta_evt+0x247/0x450
        hci_event_packet+0x61b/0xe90
        hci_rx_work+0x4d5/0xc50
        process_one_work+0x8fb/0x15a0
        worker_thread+0x576/0x1240
        kthread+0x29d/0x340
        ret_from_fork+0x1f/0x30

    Freed by task 45:
        kasan_save_stack+0x1e/0x40
        kasan_set_track+0x21/0x30
        kasan_set_free_info+0x20/0x30
        __kasan_slab_free+0xfb/0x130
        kfree+0xac/0x350
        hci_conn_cleanup+0x101/0x6a0
        hci_conn_del+0x27e/0x6c0
        hci_disconn_phylink_complete_evt+0xe0/0x120
        hci_event_packet+0x812/0xe90
        hci_rx_work+0x4d5/0xc50
        process_one_work+0x8fb/0x15a0
        worker_thread+0x576/0x1240
        kthread+0x29d/0x340
        ret_from_fork+0x1f/0x30

    The buggy address belongs to the object at ffff88800c0f0500
    The buggy address is located 24 bytes inside of
    which belongs to the cache kmalloc-128 of size 128
    The buggy address belongs to the page:
    128-byte region [ffff88800c0f0500, ffff88800c0f0580)
    flags: 0x100000000000200(slab|node=0|zone=1)
    page:00000000fe45cd86 refcount:1 mapcount:0
    mapping:0000000000000000 index:0x0 pfn:0xc0f0
    raw: 0000000000000000 0000000080100010 00000001ffffffff
    0000000000000000
    raw: 0100000000000200 ffffea00003a2c80 dead000000000004
    ffff8880078418c0
    page dumped because: kasan: bad access detected
    ffff88800c0f0400: 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc
    Memory state around the buggy address:
    >ffff88800c0f0500: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
    ffff88800c0f0480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
    ffff88800c0f0580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
                                ^
    ==================================================================
    ffff88800c0f0600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
---
 net/bluetooth/hci_event.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
net/bluetooth/hci_event.c +2 -1
index 39e222fb3004..4eeba9dfb38f 100644
@@ -4470,8 +4470,9 @@ static void hci_disconn_phylink_complete_evt(struct hci_dev *hdev,
 	hci_dev_lock(hdev);
 
 	hcon = hci_conn_hash_lookup_handle(hdev, ev->phy_handle);
-	if (hcon) {
+	if (hcon && hcon->type == AMP_LINK) {
 		hcon->state = BT_CLOSED;
+		hci_disconn_cfm(hcon, ev->reason);
 		hci_conn_del(hcon);
 	}
 
Signature · 1 line
2.34.1
author maintainer
#21 lore raw

PATCH 22/22 init/main.c: return 1 from handled __setup() functions

In reply to Sasha Levin

From: Randy Dunlap <[email protected]>

[ Upstream commit f9a40b0890658330c83c95511f9d6b396610defc ]

initcall_blacklist() should return 1 to indicate that it handled its cmdline arguments.

set_debug_rodata() should return 1 to indicate that it handled its cmdline arguments. Print a warning if the option string is invalid.

This prevents these strings from being added to the 'init' program's environment as they are not init arguments/parameters.

---
 init/main.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
init/main.c +4 -2
index f0b2411a5fbf..621cedd9173a 100644
@@ -749,7 +749,7 @@ static int __init initcall_blacklist(char *str)
 		}
 	} while (str_entry);
 
-	return 0;
+	return 1;
 }
 
 static bool __init_or_module initcall_blacklisted(initcall_t fn)
@@ -965,7 +965,9 @@ static noinline void __init kernel_init_freeable(void);
 bool rodata_enabled __ro_after_init = true;
 static int __init set_debug_rodata(char *str)
 {
-	return strtobool(str, &rodata_enabled);
+	if (strtobool(str, &rodata_enabled))
+		pr_warn("Invalid option string for rodata: '%s'\n", str);
+	return 1;
 }
 __setup("rodata=", set_debug_rodata);
 #endif
Signature · 1 line
2.34.1