ath9k: Properly clear TX status area before reporting to mac80211
Toke Høiland-Jørgensen
maintainerPATCH 1/1 ath9k: Properly clear TX status area before reporting to mac80211
The ath9k driver was not properly clearing the status area in the ieee80211_tx_info struct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.
Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
--- drivers/net/wireless/ath/ath9k/xmit.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)
drivers/net/wireless/ath/ath9k/xmit.c +2 -3
@@ -2553,6 +2553,8 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +ieee80211_tx_info_clear_status (tx_info); +if (txok) tx_info->status.ack_signal = ts->ts_rssi;
@@ -2595,9 +2597,6 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, } tx_info->status.rates[tx_rateindex].count = ts->ts_longretry +1 ; - -/* we report airtime in ath_tx_count_airtime(), don't report twice */ - tx_info->status.tx_time =0 ; }static void ath_tx_processq (struct ath_softc *sc,struct ath_txq *txq)
Signature · 1 line
2.35.1
Quoted 14 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Quoted 3 lines
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>
No regressions and UBSAN warning [1] reported on dmesg.
However, there is something missing. I don't see Cc: [email protected] trailer in this patch. I think it should, because I reported that this issue first occurred on v5.17, then still appeared on v5.17.1.
Signature · 1 line
An old man doll... just what I always wanted! - Clara
Quoted 8 lines · Bagas Sanjaya
No regressions and UBSAN warning [1] reported on dmesg.
Tested-by Bagas Sanjaya <[email protected]>However, there is something missing. I don't see Cc: [email protected] trailer in this patch. I think it should, because I reported that this issue first occurred on v5.17, then still appeared on v5.17.1.
Oops, missing link for [1].
Signature · 1 line
An old man doll... just what I always wanted! - Clara
Quoted 19 lines · Bagas Sanjaya
Quoted 14 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Quoted 3 lines
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>
Quoted 7 lines
No regressions and UBSAN warning [1] reported on dmesg.
Tested-by Bagas Sanjaya <[email protected]>However, there is something missing. I don't see Cc: [email protected] trailer in this patch. I think it should, because I reported that this issue first occurred on v5.17, then still appeared on v5.17.1.
I can add that during commit.
Signature · 3 lines
https://patchwork.kernel.org/project/linux-wireless/list/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
Toke Høiland-Jørgensen
maintainerQuoted 23 lines · Kalle Valo
Quoted 21 lines · Bagas Sanjaya
Quoted 14 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Quoted 3 lines
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>No regressions and UBSAN warning [1] reported on dmesg.
Quoted 7 lines
Quoted 5 lines
Tested-by Bagas Sanjaya <[email protected]>However, there is something missing. I don't see Cc: [email protected] trailer in this patch. I think it should, because I reported that this issue first occurred on v5.17, then still appeared on v5.17.1.
I can add that during commit.
Thanks! And sorry about that, I have gotten so used to the netdev policy of not including an explicit stable Cc that I totally forgot that this doesn't apply to the wireless tree.
In any case I think the stable tree autoselection bit should pick it up from the Fixes tag, though...
-Toke
Quoted 31 lines · Toke Høiland-Jørgensen
Quoted 29 lines · Kalle Valo
Quoted 26 lines · Bagas Sanjaya
Quoted 14 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Quoted 3 lines
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>No regressions and UBSAN warning [1] reported on dmesg.
Tested-by Bagas Sanjaya <[email protected]>However, there is something missing. I don't see Cc: [email protected] trailer in this patch. I think it should, because I reported that this issue first occurred on v5.17, then still appeared on v5.17.1.
Quoted 5 lines
Quoted 1 line
I can add that during commit.
Thanks! And sorry about that, I have gotten so used to the netdev policy of not including an explicit stable Cc that I totally forgot that this doesn't apply to the wireless tree.
No worries!
Quoted 2 lines
In any case I think the stable tree autoselection bit should pick it up from the Fixes tag, though...
Yeah, I agree. I also only add the Fixes tag to my patches, and let the stable team to choose if they want the commit or not. But if people ask to add cc stable I'll do that, it's easy enough as I have the edit command in my patchwork script :)
Signature · 3 lines
https://patchwork.kernel.org/project/linux-wireless/list/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
Quoted 14 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Quoted 5 lines
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Cc <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>Tested-by Bagas Sanjaya <[email protected]>
Patch applied to wireless.git, thanks.
037250f0a45c ath9k: Properly clear TX status area before reporting to mac80211
Signature · 3 lines
https://patchwork.kernel.org/project/linux-wireless/patch/[email protected]/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
Hello Toke,
Quoted 26 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>--- drivers/net/wireless/ath/ath9k/xmit.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)drivers/net/wireless/ath/ath9k/xmit.c +0
-0
drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2557
Quoted 5 lines
drivers/net/wireless/ath/ath9k/xmit.c +2
-0@@ -2553,6 +2553,8 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +ieee80211_tx_info_clear_status (tx_info); +
As this also clears the status.rates[].count, see include/net/mac80211.h:
1195 static inline void
1196 ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) 1197 {
1198 int i;
1199
1200 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
1201 offsetof(struct ieee80211_tx_info, control.rates));
1202 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
1203 offsetof(struct ieee80211_tx_info, driver_rates));
1204 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8) ; 1205 /* clear the rate counts */ 1206 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
1207 info->status.rates[i].count = 0;
1208 memset_after(&info->status, 0, rates);
1209 }
I would have expected some lines added to restore the count (for the rates with index < tx_rateindex), e.g. as done in drivers/net/wireless/ath/ath5k/base.c:
1731 ieee80211_tx_info_clear_status(info);
1732
1733 for (i = 0; i < ts->ts_final_idx; i++) {
1734 struct ieee80211_tx_rate *r =
1735 &info->status.rates[i];
1736
1737 r->count = tries[i];
1738 }
In drivers/net/wireless/ath/ath9k/xmit.c this is only done/changed for the tx_rateindex index (which is often zero in case the first suggested rate succeeds, but in noisy environment is sometimes > 0)...
drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2602
Quoted 13 lines
drivers/net/wireless/ath/ath9k/xmit.c +0
-3if (txok) tx_info->status.ack_signal = ts->ts_rssi;@@ -2595,9 +2597,6 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, } tx_info->status.rates[)].count = ts->ts_longretry + 1; - -/* we report airtime in ath_tx_count_airtime(), don't report twice */ - tx_info->status.tx_time =0 ; }static void ath_tx_processq (struct ath_softc *sc,struct ath_txq *txq)
And from drivers/net/wireless/ath/ath9k/xmit.c:
2592 for (i = tx_rateindex + 1; i < hw->max_rates; i++) {
2593 tx_info->status.rates[i].count = 0;
2594 tx_info->status.rates[i].idx = -1;
2595 }
Line 2593 can be deleted as status.rates[].count is already zeroed through the ieee80211_tx_info_clear_status() call...
And it should be sufficient to do:
if (tx_rateindex + 1 < hw->max_rates) tx_info->status.rates[tx_rateindex + 1].idx = -1;
Regards,
Peter
Toke Høiland-Jørgensen
maintainerQuoted 67 lines · Peter Seiderer
Hello Toke,
Quoted 26 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>--- drivers/net/wireless/ath/ath9k/xmit.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)drivers/net/wireless/ath/ath9k/xmit.c +0
-0drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2557
Quoted 5 lines
drivers/net/wireless/ath/ath9k/xmit.c +2
-0@@ -2553,6 +2553,8 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +ieee80211_tx_info_clear_status (tx_info); +As this also clears the status.rates[].count, see
include/net/mac80211.h:1195 static inline void
1196ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)1197 {
1198 int i;
1199
1200 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1201offsetof(struct ieee80211_tx_info, control.rates));
1202 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1203offsetof(struct ieee80211_tx_info, driver_rates));1204 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8) ; 1205 /* clear the rate counts */ 1206 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)1207 info->status.rates[i].count = 0;
1208memset_after(&info->status, 0, rates);
1209 }I would have expected some lines added to restore the count (for the rates with index <
tx_rateindex), e.g. as done indrivers/net/wireless/ath/ath5k/base.c:1731
ieee80211_tx_info_clear_status(info);
1732
1733 for (i = 0; i <ts->ts_final_idx; i++) {
1734 structieee80211_tx_rate*r =
1735 &info->status.rates[i];
1736
1737r->count= tries[i];
1738 }
Quoted 3 lines
In
drivers/net/wireless/ath/ath9k/xmit.cthis is only done/changed for thetx_rateindexindex (which is often zero in case the first suggested rate succeeds, but in noisy environment is sometimes > 0)...
Ah, you're right! I looked at that code, and somehow parsed that as "OK, it's setting all the rate counts, we're fine". But obviously that's not what that code is doing, so we'll lose some information now. Bugger :(
I'll send a follow-up, thanks for flagging this!
-Toke
Hello Toke,
Quoted 96 lines · Peter Seiderer
Hello Toke,
Quoted 26 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>--- drivers/net/wireless/ath/ath9k/xmit.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)drivers/net/wireless/ath/ath9k/xmit.c +0
-0drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2557
Quoted 5 lines
drivers/net/wireless/ath/ath9k/xmit.c +2
-0@@ -2553,6 +2553,8 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +ieee80211_tx_info_clear_status (tx_info); +As this also clears the status.rates[].count, see
include/net/mac80211.h:1195 static inline void
1196ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)1197 {
1198 int i;
1199
1200 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1201offsetof(struct ieee80211_tx_info, control.rates));
1202 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1203offsetof(struct ieee80211_tx_info, driver_rates));1204 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8) ; 1205 /* clear the rate counts */ 1206 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)1207 info->status.rates[i].count = 0;
1208memset_after(&info->status, 0, rates);
1209 }I would have expected some lines added to restore the count (for the rates with index <
tx_rateindex), e.g. as done indrivers/net/wireless/ath/ath5k/base.c:1731
ieee80211_tx_info_clear_status(info);
1732
1733 for (i = 0; i <ts->ts_final_idx; i++) {
1734 structieee80211_tx_rate*r =
1735 &info->status.rates[i];
1736
1737r->count= tries[i];
1738 }In
drivers/net/wireless/ath/ath9k/xmit.cthis is only done/changed for thetx_rateindexindex (which is often zero in case the first suggested rate succeeds, but in noisy environment is sometimes > 0)...drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2602
Quoted 13 lines
drivers/net/wireless/ath/ath9k/xmit.c +0
-3if (txok) tx_info->status.ack_signal = ts->ts_rssi;@@ -2595,9 +2597,6 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, } tx_info->status.rates[)].count = ts->ts_longretry + 1; - -/* we report airtime in ath_tx_count_airtime(), don't report twice */ - tx_info->status.tx_time =0 ; }static void ath_tx_processq (struct ath_softc *sc,struct ath_txq *txq)And from
drivers/net/wireless/ath/ath9k/xmit.c:2592 for (i =
tx_rateindex+ 1; i <hw->max_rates; i++) {
2593 tx_info->status.rates[i].count = 0;
2594 tx_info->status.rates[i].idx = -1;
2595 }Line 2593 can be deleted as status.rates[].count is already zeroed through the
ieee80211_tx_info_clear_status()call...
Quoted 7 lines
And it should be sufficient to do:
if (tx_rateindex + 1 < hw->max_rates) tx_info->status.rates[tx_rateindex + 1].idx = -1;Regards,
Peter
And one additional problem found with your patch applied (to 5.16.18), the log get spammed by:
[ 445.489139] ------------[ cut here ]------------ [ 445.489150] WARNING: CPU: 0 PID: 8630 at drivers/net/wireless/ath/ath9k/xmit.c:174 ath_tx_complete+0x190/0x1a0 [ath9k] [ 445.489178] Modules linked in: ath9k ath9k_common ath9k_hw mac80211 ppp_async ppp_generic slhc xt_u32 xt_TCPMSS xt_tcpmss xt_MASQUERADE iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip6table_filter iptable_filter ip6table_mangle ip6_tables cls_u32 sch_prio qmi_wwan cdc_wdm usbnet qcserial usb_wwan gpio_pca953x xt_tcpudp xt_mark iptable_mangle ip_tables x_tables dummy tqmx86_wdt watchdog i2c_machxo2 gpio_tqmx86 libarc4 ath tqmx86 mfd_core ftdi_sio cfg80211 usbserial nct7802 regmap_i2c [last unloaded: mac80211] [ 445.489298] CPU: 0 PID: 8630 Comm: modprobe Tainted: G W 5.16.18+ #2 [ 445.489307] Hardware name: TQ-Group TQMxE38M X64/Type2 - Board Product Name, BIOS TQMxE38M.5.4.48.0028.12 01/31/2017 [ 445.489311] EIP: ath_tx_complete+0x190/0x1a0 [ath9k] [ 445.489328] Code: ff 75 e8 68 d7 a1 2c f8 89 55 ec e8 d5 4f e3 ff 8b 45 f0 8b 55 ec 83 c4 10 8b 80 58 0a 00 00 e9 a8 fe ff ff 8d b6 00 00 00 00 <0f> 0b c7 42 68 00 00 00 00 e9 1d ff ff ff 66 90 55 89 e5 57 56 89 [ 445.489336] EAX: 00000000 EBX: c2e67900 ECX: c23cc040 EDX: c235a980 [ 445.489342] ESI: c235a888 EDI: c2359860 EBP: c1089e18 ESP: c1089dfc [ 445.489348] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 EFLAGS: 00010297 [ 445.489355] CR0: 80050033 CR2: b7f81000 CR3: 02ec7000 CR4: 001006d0 [ 445.489362] Call Trace: [ 445.489366] <SOFTIRQ> [ 445.489372] ath_tx_complete_buf+0x100/0x130 [ath9k] [ 445.489390] ath_tx_process_buffer+0x187/0xb40 [ath9k] [ 445.489407] ? resched_curr+0x1d/0xc0 [ 445.489419] ? check_preempt_wakeup+0x115/0x250 [ 445.489429] ? task_fork_fair+0xc0/0x170 [ 445.489436] ? put_prev_task_fair+0x40/0x40 [ 445.489444] ? check_preempt_curr+0x62/0x70 [ 445.489452] ? __local_bh_enable_ip+0x33/0x80 [ 445.489460] ? _raw_spin_unlock_bh+0x13/0x20 [ 445.489468] ? ath_txq_unlock_complete+0x5a/0x100 [ath9k] [ 445.489485] ? _raw_spin_unlock_irqrestore+0x16/0x30 [ 445.489492] ? try_to_wake_up+0x7c/0x550 [ 445.489499] ath_tx_tasklet+0x1de/0x2e0 [ath9k] [ 445.489519] ath9k_tasklet+0x22f/0x330 [ath9k] [ 445.489535] tasklet_action_common.constprop.0+0x89/0xb0 [ 445.489544] tasklet_action+0x21/0x30 [ 445.489551] __do_softirq+0xc5/0x28b [ 445.489559] ? __entry_text_end+0x4/0x4 [ 445.489567] call_on_stack+0x40/0x50 [ 445.489576] </SOFTIRQ> [ 445.489580] ? irq_exit_rcu+0x92/0x100 [ 445.489587] ? common_interrupt+0x27/0x40 [ 445.489595] ? asm_common_interrupt+0x102/0x140 [ 445.489605] ---[ end trace 5c176b666255bca1 ]--- [ 445.607206] ------------[ cut here ]------------
Could be fixed by the following additional change:
drivers/net/wireless/ath/ath9k/xmit.c +3 -0
@@ -2511,9 +2511,12 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ieee80211_hw *hw = sc->hw;struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +bool is_valid_ack_signal = tx_info->status.is_valid_ack_signal;ieee80211_tx_info_clear_status (tx_info); + tx_info->status.is_valid_ack_signal = is_valid_ack_signal; +if (txok)
Regards,
Peter
Toke Høiland-Jørgensen
maintainerQuoted 156 lines · Peter Seiderer
Hello Toke,
Quoted 96 lines · Peter Seiderer
Hello Toke,
Quoted 26 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>--- drivers/net/wireless/ath/ath9k/xmit.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)drivers/net/wireless/ath/ath9k/xmit.c +0
-0drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2557
Quoted 5 lines
drivers/net/wireless/ath/ath9k/xmit.c +2
-0@@ -2553,6 +2553,8 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +ieee80211_tx_info_clear_status (tx_info); +As this also clears the status.rates[].count, see
include/net/mac80211.h:1195 static inline void
1196ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)1197 {
1198 int i;
1199
1200 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1201offsetof(struct ieee80211_tx_info, control.rates));
1202 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1203offsetof(struct ieee80211_tx_info, driver_rates));1204 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8) ; 1205 /* clear the rate counts */ 1206 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)1207 info->status.rates[i].count = 0;
1208memset_after(&info->status, 0, rates);
1209 }I would have expected some lines added to restore the count (for the rates with index <
tx_rateindex), e.g. as done indrivers/net/wireless/ath/ath5k/base.c:1731
ieee80211_tx_info_clear_status(info);
1732
1733 for (i = 0; i <ts->ts_final_idx; i++) {
1734 structieee80211_tx_rate*r =
1735 &info->status.rates[i];
1736
1737r->count= tries[i];
1738 }In
drivers/net/wireless/ath/ath9k/xmit.cthis is only done/changed for thetx_rateindexindex (which is often zero in case the first suggested rate succeeds, but in noisy environment is sometimes > 0)...drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2602
Quoted 13 lines
drivers/net/wireless/ath/ath9k/xmit.c +0
-3if (txok) tx_info->status.ack_signal = ts->ts_rssi;@@ -2595,9 +2597,6 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, } tx_info->status.rates[)].count = ts->ts_longretry + 1; - -/* we report airtime in ath_tx_count_airtime(), don't report twice */ - tx_info->status.tx_time =0 ; }static void ath_tx_processq (struct ath_softc *sc,struct ath_txq *txq)And from
drivers/net/wireless/ath/ath9k/xmit.c:2592 for (i =
tx_rateindex+ 1; i <hw->max_rates; i++) {
2593 tx_info->status.rates[i].count = 0;
2594 tx_info->status.rates[i].idx = -1;
2595 }Line 2593 can be deleted as status.rates[].count is already zeroed through the
ieee80211_tx_info_clear_status()call...Quoted 7 lines
And it should be sufficient to do:
if (tx_rateindex + 1 < hw->max_rates) tx_info->status.rates[tx_rateindex + 1].idx = -1;Regards,
PeterAnd one additional problem found with your patch applied (to 5.16.18), the log get spammed by:
[ 445.489139] ------------[ cut here ]------------ [ 445.489150] WARNING: CPU: 0 PID: 8630 at drivers/net/wireless/ath/ath9k/xmit.c:174 ath_tx_complete+0x190/0x1a0 [ath9k] [ 445.489178] Modules linked in: ath9k ath9k_common ath9k_hw mac80211 ppp_async ppp_generic slhc xt_u32 xt_TCPMSS xt_tcpmss xt_MASQUERADE iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip6table_filter iptable_filter ip6table_mangle ip6_tables cls_u32 sch_prio qmi_wwan cdc_wdm usbnet qcserial usb_wwan gpio_pca953x xt_tcpudp xt_mark iptable_mangle ip_tables x_tables dummy tqmx86_wdt watchdog i2c_machxo2 gpio_tqmx86 libarc4 ath tqmx86 mfd_core ftdi_sio cfg80211 usbserial nct7802 regmap_i2c [last unloaded: mac80211] [ 445.489298] CPU: 0 PID: 8630 Comm: modprobe Tainted: G W 5.16.18+ #2 [ 445.489307] Hardware name: TQ-Group TQMxE38M X64/Type2 - Board Product Name, BIOS TQMxE38M.5.4.48.0028.12 01/31/2017 [ 445.489311] EIP: ath_tx_complete+0x190/0x1a0 [ath9k] [ 445.489328] Code: ff 75 e8 68 d7 a1 2c f8 89 55 ec e8 d5 4f e3 ff 8b 45 f0 8b 55 ec 83 c4 10 8b 80 58 0a 00 00 e9 a8 fe ff ff 8d b6 00 00 00 00 <0f> 0b c7 42 68 00 00 00 00 e9 1d ff ff ff 66 90 55 89 e5 57 56 89 [ 445.489336] EAX: 00000000 EBX: c2e67900 ECX: c23cc040 EDX: c235a980 [ 445.489342] ESI: c235a888 EDI: c2359860 EBP: c1089e18 ESP: c1089dfc [ 445.489348] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 EFLAGS: 00010297 [ 445.489355] CR0: 80050033 CR2: b7f81000 CR3: 02ec7000 CR4: 001006d0 [ 445.489362] Call Trace: [ 445.489366] <SOFTIRQ> [ 445.489372] ath_tx_complete_buf+0x100/0x130 [ath9k] [ 445.489390] ath_tx_process_buffer+0x187/0xb40 [ath9k] [ 445.489407] ? resched_curr+0x1d/0xc0 [ 445.489419] ? check_preempt_wakeup+0x115/0x250 [ 445.489429] ? task_fork_fair+0xc0/0x170 [ 445.489436] ? put_prev_task_fair+0x40/0x40 [ 445.489444] ? check_preempt_curr+0x62/0x70 [ 445.489452] ? __local_bh_enable_ip+0x33/0x80 [ 445.489460] ? _raw_spin_unlock_bh+0x13/0x20 [ 445.489468] ? ath_txq_unlock_complete+0x5a/0x100 [ath9k] [ 445.489485] ? _raw_spin_unlock_irqrestore+0x16/0x30 [ 445.489492] ? try_to_wake_up+0x7c/0x550 [ 445.489499] ath_tx_tasklet+0x1de/0x2e0 [ath9k] [ 445.489519] ath9k_tasklet+0x22f/0x330 [ath9k] [ 445.489535] tasklet_action_common.constprop.0+0x89/0xb0 [ 445.489544] tasklet_action+0x21/0x30 [ 445.489551] __do_softirq+0xc5/0x28b [ 445.489559] ? __entry_text_end+0x4/0x4 [ 445.489567] call_on_stack+0x40/0x50 [ 445.489576] </SOFTIRQ> [ 445.489580] ? irq_exit_rcu+0x92/0x100 [ 445.489587] ? common_interrupt+0x27/0x40 [ 445.489595] ? asm_common_interrupt+0x102/0x140 [ 445.489605] ---[ end trace 5c176b666255bca1 ]--- [ 445.607206] ------------[ cut here ]------------Could be fixed by the following additional change:
drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2520
Quoted 10 lines
drivers/net/wireless/ath/ath9k/xmit.c +3
-0@@ -2511,9 +2511,12 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ieee80211_hw *hw = sc->hw;struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +bool is_valid_ack_signal = tx_info->status.is_valid_ack_signal;ieee80211_tx_info_clear_status (tx_info); + tx_info->status.is_valid_ack_signal = is_valid_ack_signal; +if (txok)
That doesn't seem right, zeroing is_valid_ack_signal was the whole point of the first patch... Something seems off in that backtrace; could you try running it through ./scripts/decode_stacktrace.sh please?
-Toke
Hello Toke,
Quoted 165 lines · Toke Høiland-Jørgensen
Quoted 163 lines · Peter Seiderer
Hello Toke,
Quoted 96 lines · Peter Seiderer
Hello Toke,
Quoted 26 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>--- drivers/net/wireless/ath/ath9k/xmit.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)drivers/net/wireless/ath/ath9k/xmit.c +0
-0drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2557
Quoted 5 lines
drivers/net/wireless/ath/ath9k/xmit.c +2
-0@@ -2553,6 +2553,8 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +ieee80211_tx_info_clear_status (tx_info); +As this also clears the status.rates[].count, see
include/net/mac80211.h:1195 static inline void
1196ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)1197 {
1198 int i;
1199
1200 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1201offsetof(struct ieee80211_tx_info, control.rates));
1202 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1203offsetof(struct ieee80211_tx_info, driver_rates));1204 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8) ; 1205 /* clear the rate counts */ 1206 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)1207 info->status.rates[i].count = 0;
1208memset_after(&info->status, 0, rates);
1209 }I would have expected some lines added to restore the count (for the rates with index <
tx_rateindex), e.g. as done indrivers/net/wireless/ath/ath5k/base.c:1731
ieee80211_tx_info_clear_status(info);
1732
1733 for (i = 0; i <ts->ts_final_idx; i++) {
1734 structieee80211_tx_rate*r =
1735 &info->status.rates[i];
1736
1737r->count= tries[i];
1738 }In
drivers/net/wireless/ath/ath9k/xmit.cthis is only done/changed for thetx_rateindexindex (which is often zero in case the first suggested rate succeeds, but in noisy environment is sometimes > 0)...drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2602
Quoted 13 lines
drivers/net/wireless/ath/ath9k/xmit.c +0
-3if (txok) tx_info->status.ack_signal = ts->ts_rssi;@@ -2595,9 +2597,6 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, } tx_info->status.rates[)].count = ts->ts_longretry + 1; - -/* we report airtime in ath_tx_count_airtime(), don't report twice */ - tx_info->status.tx_time =0 ; }static void ath_tx_processq (struct ath_softc *sc,struct ath_txq *txq)And from
drivers/net/wireless/ath/ath9k/xmit.c:2592 for (i =
tx_rateindex+ 1; i <hw->max_rates; i++) {
2593 tx_info->status.rates[i].count = 0;
2594 tx_info->status.rates[i].idx = -1;
2595 }Line 2593 can be deleted as status.rates[].count is already zeroed through the
ieee80211_tx_info_clear_status()call...Quoted 7 lines
And it should be sufficient to do:
if (tx_rateindex + 1 < hw->max_rates) tx_info->status.rates[tx_rateindex + 1].idx = -1;Regards,
PeterAnd one additional problem found with your patch applied (to 5.16.18), the log get spammed by:
[ 445.489139] ------------[ cut here ]------------ [ 445.489150] WARNING: CPU: 0 PID: 8630 at drivers/net/wireless/ath/ath9k/xmit.c:174 ath_tx_complete+0x190/0x1a0 [ath9k] [ 445.489178] Modules linked in: ath9k ath9k_common ath9k_hw mac80211 ppp_async ppp_generic slhc xt_u32 xt_TCPMSS xt_tcpmss xt_MASQUERADE iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip6table_filter iptable_filter ip6table_mangle ip6_tables cls_u32 sch_prio qmi_wwan cdc_wdm usbnet qcserial usb_wwan gpio_pca953x xt_tcpudp xt_mark iptable_mangle ip_tables x_tables dummy tqmx86_wdt watchdog i2c_machxo2 gpio_tqmx86 libarc4 ath tqmx86 mfd_core ftdi_sio cfg80211 usbserial nct7802 regmap_i2c [last unloaded: mac80211] [ 445.489298] CPU: 0 PID: 8630 Comm: modprobe Tainted: G W 5.16.18+ #2 [ 445.489307] Hardware name: TQ-Group TQMxE38M X64/Type2 - Board Product Name, BIOS TQMxE38M.5.4.48.0028.12 01/31/2017 [ 445.489311] EIP: ath_tx_complete+0x190/0x1a0 [ath9k] [ 445.489328] Code: ff 75 e8 68 d7 a1 2c f8 89 55 ec e8 d5 4f e3 ff 8b 45 f0 8b 55 ec 83 c4 10 8b 80 58 0a 00 00 e9 a8 fe ff ff 8d b6 00 00 00 00 <0f> 0b c7 42 68 00 00 00 00 e9 1d ff ff ff 66 90 55 89 e5 57 56 89 [ 445.489336] EAX: 00000000 EBX: c2e67900 ECX: c23cc040 EDX: c235a980 [ 445.489342] ESI: c235a888 EDI: c2359860 EBP: c1089e18 ESP: c1089dfc [ 445.489348] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 EFLAGS: 00010297 [ 445.489355] CR0: 80050033 CR2: b7f81000 CR3: 02ec7000 CR4: 001006d0 [ 445.489362] Call Trace: [ 445.489366] <SOFTIRQ> [ 445.489372] ath_tx_complete_buf+0x100/0x130 [ath9k] [ 445.489390] ath_tx_process_buffer+0x187/0xb40 [ath9k] [ 445.489407] ? resched_curr+0x1d/0xc0 [ 445.489419] ? check_preempt_wakeup+0x115/0x250 [ 445.489429] ? task_fork_fair+0xc0/0x170 [ 445.489436] ? put_prev_task_fair+0x40/0x40 [ 445.489444] ? check_preempt_curr+0x62/0x70 [ 445.489452] ? __local_bh_enable_ip+0x33/0x80 [ 445.489460] ? _raw_spin_unlock_bh+0x13/0x20 [ 445.489468] ? ath_txq_unlock_complete+0x5a/0x100 [ath9k] [ 445.489485] ? _raw_spin_unlock_irqrestore+0x16/0x30 [ 445.489492] ? try_to_wake_up+0x7c/0x550 [ 445.489499] ath_tx_tasklet+0x1de/0x2e0 [ath9k] [ 445.489519] ath9k_tasklet+0x22f/0x330 [ath9k] [ 445.489535] tasklet_action_common.constprop.0+0x89/0xb0 [ 445.489544] tasklet_action+0x21/0x30 [ 445.489551] __do_softirq+0xc5/0x28b [ 445.489559] ? __entry_text_end+0x4/0x4 [ 445.489567] call_on_stack+0x40/0x50 [ 445.489576] </SOFTIRQ> [ 445.489580] ? irq_exit_rcu+0x92/0x100 [ 445.489587] ? common_interrupt+0x27/0x40 [ 445.489595] ? asm_common_interrupt+0x102/0x140 [ 445.489605] ---[ end trace 5c176b666255bca1 ]--- [ 445.607206] ------------[ cut here ]------------Could be fixed by the following additional change:
drivers/net/wireless/ath/ath9k/xmit.c +1
-0@@ -2511,9 +2511,12 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ieee80211_hw *hw = sc->hw;struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +bool is_valid_ack_signal = tx_info->status.is_valid_ack_signal;ieee80211_tx_info_clear_status (tx_info);
Quoted 7 lines
drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2520
Quoted 3 lines
drivers/net/wireless/ath/ath9k/xmit.c +2
-0+ tx_info->status.is_valid_ack_signal = is_valid_ack_signal; +if (txok)That doesn't seem right, zeroing
is_valid_ack_signalwas the whole point of the first patch... Something seems off in that backtrace; could you try running it through./scripts/decode_stacktrace.shplease?
Will do (and re-run the test with an fresh compiled kernel as CONFIG_DEBUG_KERNEL was not set - but need to wait until next week as I need physical access to the test system for kernel update)...
Regards,
Peter
Quoted 2 lines
-Toke
Hello Toke,
Quoted 177 lines · Peter Seiderer
Hello Toke,
Quoted 165 lines · Toke Høiland-Jørgensen
Quoted 163 lines · Peter Seiderer
Hello Toke,
Quoted 96 lines · Peter Seiderer
Hello Toke,
Quoted 26 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>--- drivers/net/wireless/ath/ath9k/xmit.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)drivers/net/wireless/ath/ath9k/xmit.c +0
-0drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2557
Quoted 5 lines
drivers/net/wireless/ath/ath9k/xmit.c +2
-0@@ -2553,6 +2553,8 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +ieee80211_tx_info_clear_status (tx_info); +As this also clears the status.rates[].count, see
include/net/mac80211.h:1195 static inline void
1196ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)1197 {
1198 int i;
1199
1200 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1201offsetof(struct ieee80211_tx_info, control.rates));
1202 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1203offsetof(struct ieee80211_tx_info, driver_rates));1204 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8) ; 1205 /* clear the rate counts */ 1206 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)1207 info->status.rates[i].count = 0;
1208memset_after(&info->status, 0, rates);
1209 }I would have expected some lines added to restore the count (for the rates with index <
tx_rateindex), e.g. as done indrivers/net/wireless/ath/ath5k/base.c:1731
ieee80211_tx_info_clear_status(info);
1732
1733 for (i = 0; i <ts->ts_final_idx; i++) {
1734 structieee80211_tx_rate*r =
1735 &info->status.rates[i];
1736
1737r->count= tries[i];
1738 }In
drivers/net/wireless/ath/ath9k/xmit.cthis is only done/changed for thetx_rateindexindex (which is often zero in case the first suggested rate succeeds, but in noisy environment is sometimes > 0)...drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2602
Quoted 13 lines
drivers/net/wireless/ath/ath9k/xmit.c +0
-3if (txok) tx_info->status.ack_signal = ts->ts_rssi;@@ -2595,9 +2597,6 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, } tx_info->status.rates[)].count = ts->ts_longretry + 1; - -/* we report airtime in ath_tx_count_airtime(), don't report twice */ - tx_info->status.tx_time =0 ; }static void ath_tx_processq (struct ath_softc *sc,struct ath_txq *txq)And from
drivers/net/wireless/ath/ath9k/xmit.c:2592 for (i =
tx_rateindex+ 1; i <hw->max_rates; i++) {
2593 tx_info->status.rates[i].count = 0;
2594 tx_info->status.rates[i].idx = -1;
2595 }Line 2593 can be deleted as status.rates[].count is already zeroed through the
ieee80211_tx_info_clear_status()call...Quoted 7 lines
And it should be sufficient to do:
if (tx_rateindex + 1 < hw->max_rates) tx_info->status.rates[tx_rateindex + 1].idx = -1;Regards,
PeterAnd one additional problem found with your patch applied (to 5.16.18), the log get spammed by:
[ 445.489139] ------------[ cut here ]------------ [ 445.489150] WARNING: CPU: 0 PID: 8630 at drivers/net/wireless/ath/ath9k/xmit.c:174 ath_tx_complete+0x190/0x1a0 [ath9k] [ 445.489178] Modules linked in: ath9k ath9k_common ath9k_hw mac80211 ppp_async ppp_generic slhc xt_u32 xt_TCPMSS xt_tcpmss xt_MASQUERADE iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip6table_filter iptable_filter ip6table_mangle ip6_tables cls_u32 sch_prio qmi_wwan cdc_wdm usbnet qcserial usb_wwan gpio_pca953x xt_tcpudp xt_mark iptable_mangle ip_tables x_tables dummy tqmx86_wdt watchdog i2c_machxo2 gpio_tqmx86 libarc4 ath tqmx86 mfd_core ftdi_sio cfg80211 usbserial nct7802 regmap_i2c [last unloaded: mac80211] [ 445.489298] CPU: 0 PID: 8630 Comm: modprobe Tainted: G W 5.16.18+ #2 [ 445.489307] Hardware name: TQ-Group TQMxE38M X64/Type2 - Board Product Name, BIOS TQMxE38M.5.4.48.0028.12 01/31/2017 [ 445.489311] EIP: ath_tx_complete+0x190/0x1a0 [ath9k] [ 445.489328] Code: ff 75 e8 68 d7 a1 2c f8 89 55 ec e8 d5 4f e3 ff 8b 45 f0 8b 55 ec 83 c4 10 8b 80 58 0a 00 00 e9 a8 fe ff ff 8d b6 00 00 00 00 <0f> 0b c7 42 68 00 00 00 00 e9 1d ff ff ff 66 90 55 89 e5 57 56 89 [ 445.489336] EAX: 00000000 EBX: c2e67900 ECX: c23cc040 EDX: c235a980 [ 445.489342] ESI: c235a888 EDI: c2359860 EBP: c1089e18 ESP: c1089dfc [ 445.489348] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 EFLAGS: 00010297 [ 445.489355] CR0: 80050033 CR2: b7f81000 CR3: 02ec7000 CR4: 001006d0 [ 445.489362] Call Trace: [ 445.489366] <SOFTIRQ> [ 445.489372] ath_tx_complete_buf+0x100/0x130 [ath9k] [ 445.489390] ath_tx_process_buffer+0x187/0xb40 [ath9k] [ 445.489407] ? resched_curr+0x1d/0xc0 [ 445.489419] ? check_preempt_wakeup+0x115/0x250 [ 445.489429] ? task_fork_fair+0xc0/0x170 [ 445.489436] ? put_prev_task_fair+0x40/0x40 [ 445.489444] ? check_preempt_curr+0x62/0x70 [ 445.489452] ? __local_bh_enable_ip+0x33/0x80 [ 445.489460] ? _raw_spin_unlock_bh+0x13/0x20 [ 445.489468] ? ath_txq_unlock_complete+0x5a/0x100 [ath9k] [ 445.489485] ? _raw_spin_unlock_irqrestore+0x16/0x30 [ 445.489492] ? try_to_wake_up+0x7c/0x550 [ 445.489499] ath_tx_tasklet+0x1de/0x2e0 [ath9k] [ 445.489519] ath9k_tasklet+0x22f/0x330 [ath9k] [ 445.489535] tasklet_action_common.constprop.0+0x89/0xb0 [ 445.489544] tasklet_action+0x21/0x30 [ 445.489551] __do_softirq+0xc5/0x28b [ 445.489559] ? __entry_text_end+0x4/0x4 [ 445.489567] call_on_stack+0x40/0x50 [ 445.489576] </SOFTIRQ> [ 445.489580] ? irq_exit_rcu+0x92/0x100 [ 445.489587] ? common_interrupt+0x27/0x40 [ 445.489595] ? asm_common_interrupt+0x102/0x140 [ 445.489605] ---[ end trace 5c176b666255bca1 ]--- [ 445.607206] ------------[ cut here ]------------Could be fixed by the following additional change:
drivers/net/wireless/ath/ath9k/xmit.c +1
-0@@ -2511,9 +2511,12 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ieee80211_hw *hw = sc->hw;struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +bool is_valid_ack_signal = tx_info->status.is_valid_ack_signal;ieee80211_tx_info_clear_status (tx_info);Quoted 7 lines
drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2520
Quoted 3 lines
drivers/net/wireless/ath/ath9k/xmit.c +2
-0+ tx_info->status.is_valid_ack_signal = is_valid_ack_signal; +if (txok)That doesn't seem right, zeroing
is_valid_ack_signalwas the whole point of the first patch... Something seems off in that backtrace; could you try running it through./scripts/decode_stacktrace.shplease?
Quoted 3 lines
Will do (and re-run the test with an fresh compiled kernel as
CONFIG_DEBUG_KERNELwas not set - but need to wait until next week as I need physical access to the test system for kernel update)...
Same with an fresh build (and with stacktrace run through decode_stacktrace.sh), but did some more investigations, added an debug print of tx_info->status.is_valid_ack_signal in ath_tx_rc_status() and an corresponding one in ath_txq_skb_done() printing out fi->txq, with the additional
tx_info->status.is_valid_ack_signal = is_valid_ack_signal;
line added showed the following output
[ 839.543175] XXX - ath_tx_rc_status() - is_valid_ack_signal: 2 [ 839.543195] XXX - ath_txq_skb_done() txq: 2 [ 839.617898] XXX - ath_tx_rc_status() - is_valid_ack_signal: 2 [ 839.617961] XXX - ath_txq_skb_done() txq: 2 [ 840.024845] XXX - ath_tx_rc_status() - is_valid_ack_signal: 2 [ 840.024863] XXX - ath_txq_skb_done() txq: 2
[...]
and without the following:
[ 924.614745] XXX - ath_tx_rc_status() - is_valid_ack_signal: 2 [ 924.614762] XXX - ath_txq_skb_done() txq: 0 [ 924.614805] ------------[ cut here ]------------ [ 924.614809] WARNING: CPU: 0 PID: 0 at drivers/net/wireless/ath/ath9k/xmit.c:176 ath_txq_skb_done.constprop.0+0x28/0x38 [ath9k]
[...]
Seems ieee80211_tx_info_clear_status() clears/destroys the dual use of the struct ieee80211_tx_info.status vs. ieee80211_tx_info.rate_driver_data...
See drivers/net/wireless/ath/ath9k/xmit.c
140 static struct ath_frame_info *get_frame_info(struct sk_buff *skb) 141 {
142 struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
143 BUILD_BUG_ON(sizeof(struct ath_frame_info) >
144 sizeof(tx_info->rate_driver_data));
145 return (struct ath_frame_info *) &tx_info->rate_driver_data[0];
146 }
205 static void ath_txq_skb_done(struct ath_softc *sc, struct ath_txq *txq,
206 struct sk_buff *skb)
207 {
208 struct ath_frame_info *fi = get_frame_info(skb);
209 int q = fi->txq;
210
211 if (q < 0)
212 return;
213
214 txq = sc->tx.txq_map[q];
215 if (WARN_ON(--txq->pending_frames < 0))
216 txq->pending_frames = 0;
217
218 }
Seems it only worked by chance (?) before...
Regards,
Peter
Quoted 7 lines
Regards,
PeterQuoted 2 lines
-Toke
Toke Høiland-Jørgensen
maintainerQuoted 240 lines · Peter Seiderer
Hello Toke,
Quoted 177 lines · Peter Seiderer
Hello Toke,
Quoted 165 lines · Toke Høiland-Jørgensen
Quoted 163 lines · Peter Seiderer
Hello Toke,
Quoted 96 lines · Peter Seiderer
Hello Toke,
Quoted 26 lines · Toke Høiland-Jørgensen
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_infostruct before reporting TX status to mac80211. Instead, it was manually filling in fields, which meant that fields introduced later were left as-is.Conveniently, mac80211 actually provides a helper to zero out the status area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information seems to have actually been fixing an issue that was also caused by the area being uninitialised; but it only added clearing of a single field instead of the whole struct. That is now redundant, though, so revert that commit and use it as a convenient Fixes tag.
Fixes cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status")Reported-by Bagas Sanjaya <[email protected]>Signed-off-by Toke Høiland-Jørgensen <[email protected]>--- drivers/net/wireless/ath/ath9k/xmit.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)drivers/net/wireless/ath/ath9k/xmit.c +0
-0drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2557
Quoted 5 lines
drivers/net/wireless/ath/ath9k/xmit.c +2
-0@@ -2553,6 +2553,8 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +ieee80211_tx_info_clear_status (tx_info); +As this also clears the status.rates[].count, see
include/net/mac80211.h:1195 static inline void
1196ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)1197 {
1198 int i;
1199
1200 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1201offsetof(struct ieee80211_tx_info, control.rates));
1202 BUILD_BUG_ON(offsetof(structieee80211_tx_info, status.rates) !=
1203offsetof(struct ieee80211_tx_info, driver_rates));1204 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8) ; 1205 /* clear the rate counts */ 1206 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)1207 info->status.rates[i].count = 0;
1208memset_after(&info->status, 0, rates);
1209 }I would have expected some lines added to restore the count (for the rates with index <
tx_rateindex), e.g. as done indrivers/net/wireless/ath/ath5k/base.c:1731
ieee80211_tx_info_clear_status(info);
1732
1733 for (i = 0; i <ts->ts_final_idx; i++) {
1734 structieee80211_tx_rate*r =
1735 &info->status.rates[i];
1736
1737r->count= tries[i];
1738 }In
drivers/net/wireless/ath/ath9k/xmit.cthis is only done/changed for thetx_rateindexindex (which is often zero in case the first suggested rate succeeds, but in noisy environment is sometimes > 0)...drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2602
Quoted 13 lines
drivers/net/wireless/ath/ath9k/xmit.c +0
-3if (txok) tx_info->status.ack_signal = ts->ts_rssi;@@ -2595,9 +2597,6 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, } tx_info->status.rates[)].count = ts->ts_longretry + 1; - -/* we report airtime in ath_tx_count_airtime(), don't report twice */ - tx_info->status.tx_time =0 ; }static void ath_tx_processq (struct ath_softc *sc,struct ath_txq *txq)And from
drivers/net/wireless/ath/ath9k/xmit.c:2592 for (i =
tx_rateindex+ 1; i <hw->max_rates; i++) {
2593 tx_info->status.rates[i].count = 0;
2594 tx_info->status.rates[i].idx = -1;
2595 }Line 2593 can be deleted as status.rates[].count is already zeroed through the
ieee80211_tx_info_clear_status()call...Quoted 7 lines
And it should be sufficient to do:
if (tx_rateindex + 1 < hw->max_rates) tx_info->status.rates[tx_rateindex + 1].idx = -1;Regards,
PeterAnd one additional problem found with your patch applied (to 5.16.18), the log get spammed by:
[ 445.489139] ------------[ cut here ]------------ [ 445.489150] WARNING: CPU: 0 PID: 8630 at drivers/net/wireless/ath/ath9k/xmit.c:174 ath_tx_complete+0x190/0x1a0 [ath9k] [ 445.489178] Modules linked in: ath9k ath9k_common ath9k_hw mac80211 ppp_async ppp_generic slhc xt_u32 xt_TCPMSS xt_tcpmss xt_MASQUERADE iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip6table_filter iptable_filter ip6table_mangle ip6_tables cls_u32 sch_prio qmi_wwan cdc_wdm usbnet qcserial usb_wwan gpio_pca953x xt_tcpudp xt_mark iptable_mangle ip_tables x_tables dummy tqmx86_wdt watchdog i2c_machxo2 gpio_tqmx86 libarc4 ath tqmx86 mfd_core ftdi_sio cfg80211 usbserial nct7802 regmap_i2c [last unloaded: mac80211] [ 445.489298] CPU: 0 PID: 8630 Comm: modprobe Tainted: G W 5.16.18+ #2 [ 445.489307] Hardware name: TQ-Group TQMxE38M X64/Type2 - Board Product Name, BIOS TQMxE38M.5.4.48.0028.12 01/31/2017 [ 445.489311] EIP: ath_tx_complete+0x190/0x1a0 [ath9k] [ 445.489328] Code: ff 75 e8 68 d7 a1 2c f8 89 55 ec e8 d5 4f e3 ff 8b 45 f0 8b 55 ec 83 c4 10 8b 80 58 0a 00 00 e9 a8 fe ff ff 8d b6 00 00 00 00 <0f> 0b c7 42 68 00 00 00 00 e9 1d ff ff ff 66 90 55 89 e5 57 56 89 [ 445.489336] EAX: 00000000 EBX: c2e67900 ECX: c23cc040 EDX: c235a980 [ 445.489342] ESI: c235a888 EDI: c2359860 EBP: c1089e18 ESP: c1089dfc [ 445.489348] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 EFLAGS: 00010297 [ 445.489355] CR0: 80050033 CR2: b7f81000 CR3: 02ec7000 CR4: 001006d0 [ 445.489362] Call Trace: [ 445.489366] <SOFTIRQ> [ 445.489372] ath_tx_complete_buf+0x100/0x130 [ath9k] [ 445.489390] ath_tx_process_buffer+0x187/0xb40 [ath9k] [ 445.489407] ? resched_curr+0x1d/0xc0 [ 445.489419] ? check_preempt_wakeup+0x115/0x250 [ 445.489429] ? task_fork_fair+0xc0/0x170 [ 445.489436] ? put_prev_task_fair+0x40/0x40 [ 445.489444] ? check_preempt_curr+0x62/0x70 [ 445.489452] ? __local_bh_enable_ip+0x33/0x80 [ 445.489460] ? _raw_spin_unlock_bh+0x13/0x20 [ 445.489468] ? ath_txq_unlock_complete+0x5a/0x100 [ath9k] [ 445.489485] ? _raw_spin_unlock_irqrestore+0x16/0x30 [ 445.489492] ? try_to_wake_up+0x7c/0x550 [ 445.489499] ath_tx_tasklet+0x1de/0x2e0 [ath9k] [ 445.489519] ath9k_tasklet+0x22f/0x330 [ath9k] [ 445.489535] tasklet_action_common.constprop.0+0x89/0xb0 [ 445.489544] tasklet_action+0x21/0x30 [ 445.489551] __do_softirq+0xc5/0x28b [ 445.489559] ? __entry_text_end+0x4/0x4 [ 445.489567] call_on_stack+0x40/0x50 [ 445.489576] </SOFTIRQ> [ 445.489580] ? irq_exit_rcu+0x92/0x100 [ 445.489587] ? common_interrupt+0x27/0x40 [ 445.489595] ? asm_common_interrupt+0x102/0x140 [ 445.489605] ---[ end trace 5c176b666255bca1 ]--- [ 445.607206] ------------[ cut here ]------------Could be fixed by the following additional change:
drivers/net/wireless/ath/ath9k/xmit.c +1
-0@@ -2511,9 +2511,12 @@ static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,struct ieee80211_hw *hw = sc->hw;struct ath_hw *ah = sc->sc_ah;u8 i, tx_rateindex; +bool is_valid_ack_signal = tx_info->status.is_valid_ack_signal;ieee80211_tx_info_clear_status (tx_info);Quoted 7 lines
drivers/net/wireless/ath/ath9k/xmit.c static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf, · line 2520
Quoted 3 lines
drivers/net/wireless/ath/ath9k/xmit.c +2
-0+ tx_info->status.is_valid_ack_signal = is_valid_ack_signal; +if (txok)That doesn't seem right, zeroing
is_valid_ack_signalwas the whole point of the first patch... Something seems off in that backtrace; could you try running it through./scripts/decode_stacktrace.shplease?Quoted 3 lines
Will do (and re-run the test with an fresh compiled kernel as
CONFIG_DEBUG_KERNELwas not set - but need to wait until next week as I need physical access to the test system for kernel update)...Same with an fresh build (and with stacktrace run through
decode_stacktrace.sh), but did some more investigations, added an debug print oftx_info->status.is_valid_ack_signalinath_tx_rc_status()and an corresponding one inath_txq_skb_done()printing outfi->txq, with the additionaltx_info->status.is_valid_ack_signal = is_valid_ack_signal;line added showed the following output
[ 839.543175] XXX - ath_tx_rc_status() - is_valid_ack_signal: 2 [ 839.543195] XXX - ath_txq_skb_done() txq: 2 [ 839.617898] XXX - ath_tx_rc_status() - is_valid_ack_signal: 2 [ 839.617961] XXX - ath_txq_skb_done() txq: 2 [ 840.024845] XXX - ath_tx_rc_status() - is_valid_ack_signal: 2 [ 840.024863] XXX - ath_txq_skb_done() txq: 2[...]
and without the following:
[ 924.614745] XXX - ath_tx_rc_status() - is_valid_ack_signal: 2 [ 924.614762] XXX - ath_txq_skb_done() txq: 0 [ 924.614805] ------------[ cut here ]------------ [ 924.614809] WARNING: CPU: 0 PID: 0 at drivers/net/wireless/ath/ath9k/xmit.c:176 ath_txq_skb_done.constprop.0+0x28/0x38 [ath9k][...]
Seems
ieee80211_tx_info_clear_status()clears/destroys the dual use of the struct ieee80211_tx_info.status vs. ieee80211_tx_info.rate_driver_data...See
drivers/net/wireless/ath/ath9k/xmit.c140 static struct
ath_frame_info*get_frame_info(structsk_buff*skb) 141 {
142 structieee80211_tx_info*tx_info=IEEE80211_SKB_CB(skb);
143 BUILD_BUG_ON(sizeof(structath_frame_info) >
144sizeof(tx_info->rate_driver_data));
145 return (structath_frame_info*) &tx_info->rate_driver_data[0];
146 }205 static void ath_txq_skb_done(struct
ath_softc*sc, structath_txq*txq,
206 structsk_buff*skb)
207 {
208 structath_frame_info*fi =get_frame_info(skb);
209 int q =fi->txq;
210
211 if (q < 0)
212 return;
213
214 txq = sc->tx.txq_map[q];
215 if (WARN_ON(--txq->pending_frames < 0))
216txq->pending_frames= 0;
217
218 }
Quoted 1 line
Seems it only worked by chance (?) before...
Yikes, yeah, that's no good! Also, this comment above ieee80211_tx_info_clear_status() is completely misleading:
* NOTE: You can only use this function if you do NOT use
* info->driver_data! Use info->rate_driver_data
* instead if you need only the less space that allows.
(I read that, and figured that the current use was OK, but nope, guess not!)
The ath_frame_info struct is small enough to fit into the status_driver_data field, though, so guess we could just move it there. However, ieee80211_tx_info_clear_status() also clears that AFAICT, so we'll need to save & restore it? That seems a bit odd, is this intentional Johannes?
-Toke