Skip to contentSkip to conversation

arm64: dts: ti: k3-am642-sk: Enable WLAN connected to SDHCI0

PATCH RESEND Applied Aparna M 4 participants 4 messages Apr 14, 2022 – Apr 28, 2022

Subsystems (2)
lore
Share & tools
lore

Aparna M

author
#0 lore raw

PATCH RESEND v3 1/1 arm64: dts: ti: k3-am642-sk: Enable WLAN connected to SDHCI0

From: Kishon Vijay Abraham I <[email protected]>

WL1837 module is connected to SDHCI0 in AM642 SK. Enable it here. This will enable the WiFi functionaliy on the board.

---

v3 RESEND: rebased on top of v5.18-rc2
v2 -> v3: Use generic node names for the regulators as per DT Specs v1 -> v2: Add "From" tag in commit message

 arch/arm64/boot/dts/ti/k3-am642-sk.dts | 62 ++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)
arch/arm64/boot/dts/ti/k3-am642-sk.dts +62 -0
index 1d7db8bf3a5c..59f506cbd275 100644
@@ -125,6 +125,31 @@
 		vin-supply = <&vcc_3v3_sys>;
 		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
 	};
+
+	com8_ls_en: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "com8_ls_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		pinctrl-0 = <&main_com8_ls_en_pins_default>;
+		pinctrl-names = "default";
+		gpio = <&main_gpio0 62 GPIO_ACTIVE_LOW>;
+	};
+
+	wlan_en: regulator-2 {
+		/* output of SN74AVC4T245RSVR */
+		compatible = "regulator-fixed";
+		regulator-name = "wlan_en";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		pinctrl-0 = <&main_wlan_en_pins_default>;
+		pinctrl-names = "default";
+		vin-supply = <&com8_ls_en>;
+		gpio = <&main_gpio0 48 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &main_pmx0 {
@@ -216,6 +241,23 @@
 			AM64X_IOPAD(0x0270, PIN_INPUT, 0) /* (D18) ECAP0_IN_APWM_OUT */
 		>;
 	};
+	main_wlan_en_pins_default: main-wlan-en-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x00c4, PIN_OUTPUT_PULLUP, 7) /* (V8) GPIO0_48 */
+		>;
+	};
+
+	main_com8_ls_en_pins_default: main-com8-ls-en-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x00fc, PIN_OUTPUT, 7) /* (U7) PRG1_PRU0_GPO17.GPIO0_62 */
+		>;
+	};
+
+	main_wlan_pins_default: main-wlan-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x00bc, PIN_INPUT, 7) /* (U8) GPIO0_46 */
+		>;
+	};
 };
 
 &mcu_uart0 {
@@ -293,6 +335,26 @@
 	status = "reserved";
 };
 
+&sdhci0 {
+	vmmc-supply = <&wlan_en>;
+	bus-width = <4>;
+	non-removable;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	ti,driver-strength-ohm = <50>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1837";
+		reg = <2>;
+		pinctrl-0 = <&main_wlan_pins_default>;
+		pinctrl-names = "default";
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <46 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
 &sdhci1 {
 	/* SD/MMC */
 	vmmc-supply = <&vdd_mmc1>;
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Reviewed-by on v3 1/1
#1 lore raw

On April 14, 2022 thus sayeth Aparna M:

Quoted 9 lines

From: Kishon Vijay Abraham I <[email protected]>

WL1837 module is connected to SDHCI0 in AM642 SK. Enable it here. This will enable the WiFi functionaliy on the board.

Looks good to me!

~Bryan

maintainer Applied
#2 lore raw
In reply to Aparna M

Hi Aparna M,

Quoted 6 lines · Aparna M

From: Kishon Vijay Abraham I <[email protected]>

WL1837 module is connected to SDHCI0 in AM642 SK. Enable it here. This will enable the WiFi functionaliy on the board.

I have applied the following to branch ti-k3-dts-next on [1]. Thank you!

[1/1] arm64: dts: ti: k3-am642-sk: Enable WLAN connected to SDHCI0

      commit: 065d62612e264e228c153afe9aa31d85aeea3d17

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh

Tested-by on v3 1/1
#3 lore raw
In reply to Aparna M
Quoted 9 lines · Aparna M

From: Kishon Vijay Abraham I <[email protected]>

WL1837 module is connected to SDHCI0 in AM642 SK. Enable it here. This will enable the WiFi functionaliy on the board.

Quoted 86 lines

---

v3 RESEND: rebased on top of v5.18-rc2
v2 -> v3: Use generic node names for the regulators as per DT Specs v1 -> v2: Add "From" tag in commit message

 arch/arm64/boot/dts/ti/k3-am642-sk.dts | 62 ++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)
arch/arm64/boot/dts/ti/k3-am642-sk.dts +55 -0
index 1d7db8bf3a5c..59f506cbd275 100644
@@ -125,6 +125,31 @@
 		vin-supply = <&vcc_3v3_sys>;
 		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
 	};
+
+	com8_ls_en: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "com8_ls_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		pinctrl-0 = <&main_com8_ls_en_pins_default>;
+		pinctrl-names = "default";
+		gpio = <&main_gpio0 62 GPIO_ACTIVE_LOW>;
+	};
+
+	wlan_en: regulator-2 {
+		/* output of SN74AVC4T245RSVR */
+		compatible = "regulator-fixed";
+		regulator-name = "wlan_en";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		pinctrl-0 = <&main_wlan_en_pins_default>;
+		pinctrl-names = "default";
+		vin-supply = <&com8_ls_en>;
+		gpio = <&main_gpio0 48 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &main_pmx0 {
@@ -216,6 +241,23 @@
 			AM64X_IOPAD(0x0270, PIN_INPUT, 0) /* (D18) ECAP0_IN_APWM_OUT */
 		>;
 	};
+	main_wlan_en_pins_default: main-wlan-en-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x00c4, PIN_OUTPUT_PULLUP, 7) /* (V8) GPIO0_48 */
+		>;
+	};
+
+	main_com8_ls_en_pins_default: main-com8-ls-en-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x00fc, PIN_OUTPUT, 7) /* (U7) PRG1_PRU0_GPO17.GPIO0_62 */
+		>;
+	};
+
+	main_wlan_pins_default: main-wlan-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x00bc, PIN_INPUT, 7) /* (U8) GPIO0_46 */
+		>;
+	};
 };
 
 &mcu_uart0 {
@@ -293,6 +335,26 @@
 	status = "reserved";
 };
 
+&sdhci0 {
+	vmmc-supply = <&wlan_en>;
+	bus-width = <4>;
+	non-removable;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	ti,driver-strength-ohm = <50>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1837";
+		reg = <2>;

arch/arm64/boot/dts/ti/k3-am642-sk.dts line 360

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am642-sk.dts +7 -0
+		pinctrl-0 = <&main_wlan_pins_default>;
+		pinctrl-names = "default";
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <46 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
 &sdhci1 {
 	/* SD/MMC */
 	vmmc-supply = <&vdd_mmc1>;

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel