dt-bindings: display: bridge: ldb: Implement simple NXP i.MX8M LDB bridge

The i.MX8MP contains two syscon registers which are responsible for configuring the on-SoC DPI-to-LVDS serializer. Implement a simple bridge driver for this serializer.

Signed-off-by Marek Vasut <[email protected]>

Cc Laurent Pinchart <[email protected]>

Cc Lucas Stach <[email protected]>

Cc Maxime Ripard <[email protected]>

Cc Peng Fan <[email protected]>

Cc Robby Cai <[email protected]>

Cc Robert Foss <[email protected]>

Cc Sam Ravnborg <[email protected]>

Cc Thomas Zimmermann <[email protected]>

To: [email protected]

--
V2: - Rename syscon to fsl,syscon

---
 drivers/gpu/drm/bridge/Kconfig   |   8 +
 drivers/gpu/drm/bridge/Makefile  |   1 +
 drivers/gpu/drm/bridge/nxp-ldb.c | 343 +++++++++++++++++++++++++++++++
 3 files changed, 352 insertions(+)
 create mode 100644 drivers/gpu/drm/bridge/nxp-ldb.c

drivers/gpu/drm/bridge/Kconfig +0 -0

index 20f9bc7f4be54..7fe7088a2bef5 100644

drivers/gpu/drm/bridge/Kconfig +1 -0

+
 config DRM_NXP_PTN3460
 	tristate "NXP PTN3460 DP/LVDS bridge"
 	depends on OF

drivers/gpu/drm/bridge/Makefile +1 -0

index bdffad2a7ed3a..f800b2331d9e0 100644
@@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o
 obj-$(CONFIG_DRM_LONTIUM_LT9611UXC) += lontium-lt9611uxc.o
 obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o
 obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o
+obj-$(CONFIG_DRM_NXP_LDB) += nxp-ldb.o
 obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
 obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
 obj-$(CONFIG_DRM_PARADE_PS8640) += parade-ps8640.o

drivers/gpu/drm/bridge/nxp-ldb.c new file +317 -0

new file mode 100644
index 0000000000000..7b8de235876ea
@@ -0,0 +1,343 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2022 Marek Vasut <[email protected]>
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_graph.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_of.h>
+#include <drm/drm_panel.h>
+
+#define LDB_CTRL				0x5c
+#define LDB_CTRL_CH0_ENABLE			BIT(0)
+#define LDB_CTRL_CH0_DI_SELECT			BIT(1)
+#define LDB_CTRL_CH1_ENABLE			BIT(2)
+#define LDB_CTRL_CH1_DI_SELECT			BIT(3)
+#define LDB_CTRL_SPLIT_MODE			BIT(4)
+#define LDB_CTRL_CH0_DATA_WIDTH			BIT(5)
+#define LDB_CTRL_CH0_BIT_MAPPING		BIT(6)
+#define LDB_CTRL_CH1_DATA_WIDTH			BIT(7)
+#define LDB_CTRL_CH1_BIT_MAPPING		BIT(8)
+#define LDB_CTRL_DI0_VSYNC_POLARITY		BIT(9)
+#define LDB_CTRL_DI1_VSYNC_POLARITY		BIT(10)
+#define LDB_CTRL_REG_CH0_FIFO_RESET		BIT(11)
+#define LDB_CTRL_REG_CH1_FIFO_RESET		BIT(12)
+#define LDB_CTRL_ASYNC_FIFO_ENABLE		BIT(24)
+#define LDB_CTRL_ASYNC_FIFO_THRESHOLD_MASK	GENMASK(27, 25)
+
+#define LVDS_CTRL				0x128
+#define LVDS_CTRL_CH0_EN			BIT(0)
+#define LVDS_CTRL_CH1_EN			BIT(1)
+#define LVDS_CTRL_VBG_EN			BIT(2)
+#define LVDS_CTRL_HS_EN				BIT(3)
+#define LVDS_CTRL_PRE_EMPH_EN			BIT(4)
+#define LVDS_CTRL_PRE_EMPH_ADJ(n)		(((n) & 0x7) << 5)
+#define LVDS_CTRL_PRE_EMPH_ADJ_MASK		GENMASK(7, 5)
+#define LVDS_CTRL_CM_ADJ(n)			(((n) & 0x7) << 8)
+#define LVDS_CTRL_CM_ADJ_MASK			GENMASK(10, 8)
+#define LVDS_CTRL_CC_ADJ(n)			(((n) & 0x7) << 11)
+#define LVDS_CTRL_CC_ADJ_MASK			GENMASK(13, 11)
+#define LVDS_CTRL_SLEW_ADJ(n)			(((n) & 0x7) << 14)
+#define LVDS_CTRL_SLEW_ADJ_MASK			GENMASK(16, 14)
+#define LVDS_CTRL_VBG_ADJ(n)			(((n) & 0x7) << 17)
+#define LVDS_CTRL_VBG_ADJ_MASK			GENMASK(19, 17)
+
+struct nxp_ldb {
+	struct device *dev;
+	struct drm_bridge bridge;
+	struct drm_bridge *panel_bridge;
+	struct clk *clk;
+	struct regmap *regmap;
+	bool lvds_dual_link;
+};
+
+static inline struct nxp_ldb *to_nxp_ldb(struct drm_bridge *bridge)
+{
+	return container_of(bridge, struct nxp_ldb, bridge);
+}
+
+static int nxp_ldb_attach(struct drm_bridge *bridge,
+			    enum drm_bridge_attach_flags flags)
+{
+	struct nxp_ldb *nxp_ldb = to_nxp_ldb(bridge);
+
+	return drm_bridge_attach(bridge->encoder, nxp_ldb->panel_bridge,
+				 bridge, flags);
+}
+
+static int nxp_ldb_atomic_check(struct drm_bridge *bridge,
+				struct drm_bridge_state *bridge_state,
+				struct drm_crtc_state *crtc_state,
+				struct drm_connector_state *conn_state)
+{
+	/* Invert DE signal polarity. */
+	bridge_state->input_bus_cfg.flags &= ~(DRM_BUS_FLAG_DE_LOW |
+					       DRM_BUS_FLAG_DE_HIGH);
+	if (bridge_state->output_bus_cfg.flags & DRM_BUS_FLAG_DE_LOW)
+		bridge_state->input_bus_cfg.flags |= DRM_BUS_FLAG_DE_HIGH;
+	else if (bridge_state->output_bus_cfg.flags & DRM_BUS_FLAG_DE_HIGH)
+		bridge_state->input_bus_cfg.flags |= DRM_BUS_FLAG_DE_LOW;
+
+	return 0;
+}
+
+static void nxp_ldb_atomic_enable(struct drm_bridge *bridge,
+				  struct drm_bridge_state *old_bridge_state)
+{
+	struct nxp_ldb *nxp_ldb = to_nxp_ldb(bridge);
+	struct drm_atomic_state *state = old_bridge_state->base.state;
+	const struct drm_bridge_state *bridge_state;
+	const struct drm_crtc_state *crtc_state;
+	const struct drm_display_mode *mode;
+	struct drm_connector *connector;
+	struct drm_crtc *crtc;
+	bool lvds_format_24bpp;
+	bool lvds_format_jeida;
+	u32 reg;
+
+	/* Get the LVDS format from the bridge state. */
+	bridge_state = drm_atomic_get_new_bridge_state(state, bridge);
+
+	switch (bridge_state->output_bus_cfg.format) {
+	case MEDIA_BUS_FMT_RGB666_1X7X3_SPWG:
+		lvds_format_24bpp = false;
+		lvds_format_jeida = true;
+		break;
+	case MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA:
+		lvds_format_24bpp = true;
+		lvds_format_jeida = true;
+		break;
+	case MEDIA_BUS_FMT_RGB888_1X7X4_SPWG:
+		lvds_format_24bpp = true;
+		lvds_format_jeida = false;
+		break;
+	default:
+		/*
+		 * Some bridges still don't set the correct LVDS bus pixel
+		 * format, use SPWG24 default format until those are fixed.
+		 */
+		lvds_format_24bpp = true;
+		lvds_format_jeida = false;
+		dev_warn(nxp_ldb->dev,
+			 "Unsupported LVDS bus format 0x%04x, please check output bridge driver. Falling back to SPWG24.\n",
+			 bridge_state->output_bus_cfg.format);
+		break;
+	}
+
+	/*
+	 * Retrieve the CRTC adjusted mode. This requires a little dance to go
+	 * from the bridge to the encoder, to the connector and to the CRTC.
+	 */
+	connector = drm_atomic_get_new_connector_for_encoder(state,
+							     bridge->encoder);
+	crtc = drm_atomic_get_new_connector_state(state, connector)->crtc;
+	crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
+	mode = &crtc_state->adjusted_mode;
+
+	if (nxp_ldb->lvds_dual_link)
+		clk_set_rate(nxp_ldb->clk, mode->clock * 3500);
+	else
+		clk_set_rate(nxp_ldb->clk, mode->clock * 7000);
+	clk_prepare_enable(nxp_ldb->clk);
+
+	/* Program LDB_CTRL */
+	reg = LDB_CTRL_CH0_ENABLE;
+
+	if (nxp_ldb->lvds_dual_link)
+		reg |= LDB_CTRL_CH1_ENABLE;
+
+	if (lvds_format_24bpp) {
+		reg |= LDB_CTRL_CH0_DATA_WIDTH;
+		if (nxp_ldb->lvds_dual_link)
+			reg |= LDB_CTRL_CH1_DATA_WIDTH;
+	}
+
+	if (lvds_format_jeida) {
+		reg |= LDB_CTRL_CH0_BIT_MAPPING;
+		if (nxp_ldb->lvds_dual_link)
+			reg |= LDB_CTRL_CH1_BIT_MAPPING;
+	}
+
+	if (mode->flags & DRM_MODE_FLAG_PVSYNC) {
+		reg |= LDB_CTRL_DI0_VSYNC_POLARITY;
+		if (nxp_ldb->lvds_dual_link)
+			reg |= LDB_CTRL_DI1_VSYNC_POLARITY;
+	}
+
+	regmap_write(nxp_ldb->regmap, LDB_CTRL, reg);
+
+	/* Program LVDS_CTRL */
+	reg = LVDS_CTRL_CC_ADJ(2) | LVDS_CTRL_PRE_EMPH_EN |
+	      LVDS_CTRL_PRE_EMPH_ADJ(3) | LVDS_CTRL_VBG_EN;
+	regmap_write(nxp_ldb->regmap, LVDS_CTRL, reg);
+
+	/* Wait for VBG to stabilize. */
+	usleep_range(15, 20);
+
+	reg |= LVDS_CTRL_CH0_EN;
+	if (nxp_ldb->lvds_dual_link)
+		reg |= LVDS_CTRL_CH1_EN;
+
+	regmap_write(nxp_ldb->regmap, LVDS_CTRL, reg);
+}
+
+static void nxp_ldb_atomic_disable(struct drm_bridge *bridge,
+				   struct drm_bridge_state *old_bridge_state)
+{
+	struct nxp_ldb *nxp_ldb = to_nxp_ldb(bridge);
+
+	/* Stop both channels. */
+	regmap_write(nxp_ldb->regmap, LVDS_CTRL, 0);
+	regmap_write(nxp_ldb->regmap, LDB_CTRL, 0);
+
+	clk_disable_unprepare(nxp_ldb->clk);
+}
+
+#define MAX_INPUT_SEL_FORMATS 1
+static u32 *
+nxp_ldb_atomic_get_input_bus_fmts(struct drm_bridge *bridge,
+				     struct drm_bridge_state *bridge_state,
+				     struct drm_crtc_state *crtc_state,
+				     struct drm_connector_state *conn_state,
+				     u32 output_fmt,
+				     unsigned int *num_input_fmts)
+{
+	u32 *input_fmts;
+
+	*num_input_fmts = 0;
+
+	input_fmts = kcalloc(MAX_INPUT_SEL_FORMATS, sizeof(*input_fmts),
+			     GFP_KERNEL);
+	if (!input_fmts)
+		return NULL;
+
+	input_fmts[0] = MEDIA_BUS_FMT_RGB888_1X24;
+	*num_input_fmts = MAX_INPUT_SEL_FORMATS;
+
+	return input_fmts;
+}
+
+static enum drm_mode_status
+nxp_ldb_mode_valid(struct drm_bridge *bridge,
+		   const struct drm_display_info *info,
+		   const struct drm_display_mode *mode)
+{
+	struct nxp_ldb *nxp_ldb = to_nxp_ldb(bridge);
+
+	if (mode->clock > (nxp_ldb->lvds_dual_link ? 80000 : 160000))
+		return MODE_CLOCK_HIGH;
+
+	return MODE_OK;
+}
+
+static const struct drm_bridge_funcs funcs = {
+	.attach = nxp_ldb_attach,
+	.atomic_check = nxp_ldb_atomic_check,
+	.atomic_enable = nxp_ldb_atomic_enable,
+	.atomic_disable = nxp_ldb_atomic_disable,
+	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+	.atomic_get_input_bus_fmts = nxp_ldb_atomic_get_input_bus_fmts,
+	.atomic_reset = drm_atomic_helper_bridge_reset,
+	.mode_valid = nxp_ldb_mode_valid,
+};
+
+static int nxp_ldb_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *panel_node;
+	struct device_node *port1, *port2;
+	struct drm_panel *panel;
+	struct nxp_ldb *nxp_ldb;
+	int dual_link;
+
+	nxp_ldb = devm_kzalloc(dev, sizeof(*nxp_ldb), GFP_KERNEL);
+	if (!nxp_ldb)
+		return -ENOMEM;
+
+	nxp_ldb->dev = &pdev->dev;
+	nxp_ldb->bridge.funcs = &funcs;
+	nxp_ldb->bridge.of_node = dev->of_node;
+
+	nxp_ldb->clk = devm_clk_get(dev, "ldb");
+	if (IS_ERR(nxp_ldb->clk))
+		return PTR_ERR(nxp_ldb->clk);
+
+	nxp_ldb->regmap = syscon_regmap_lookup_by_phandle(dev->of_node,
+							  "fsl,syscon");
+	if (IS_ERR(nxp_ldb->regmap))
+		return PTR_ERR(nxp_ldb->regmap);
+
+	/* Locate the panel DT node. */
+	panel_node = of_graph_get_remote_node(dev->of_node, 1, 0);
+	if (!panel_node)
+		return -ENXIO;
+
+	panel = of_drm_find_panel(panel_node);
+	of_node_put(panel_node);
+	if (IS_ERR(panel))
+		return PTR_ERR(panel);
+
+	nxp_ldb->panel_bridge = devm_drm_panel_bridge_add(dev, panel);
+	if (IS_ERR(nxp_ldb->panel_bridge))
+		return PTR_ERR(nxp_ldb->panel_bridge);
+
+	/* Determine whether this is dual-link configuration */
+	port1 = of_graph_get_port_by_id(dev->of_node, 1);
+	port2 = of_graph_get_port_by_id(dev->of_node, 2);
+	dual_link = drm_of_lvds_get_dual_link_pixel_order(port1, port2);
+	of_node_put(port1);
+	of_node_put(port2);
+
+	if (dual_link == DRM_LVDS_DUAL_LINK_EVEN_ODD_PIXELS) {
+		dev_err(dev, "LVDS channel pixel swap not supported.\n");
+		return -EINVAL;
+	}
+
+	if (dual_link == DRM_LVDS_DUAL_LINK_ODD_EVEN_PIXELS)
+		nxp_ldb->lvds_dual_link = true;
+
+	platform_set_drvdata(pdev, nxp_ldb);
+
+	drm_bridge_add(&nxp_ldb->bridge);
+
+	return 0;
+}
+
+static int nxp_ldb_remove(struct platform_device *pdev)
+{

drivers/gpu/drm/bridge/nxp-ldb.c new file +16 -0

+};
+MODULE_DEVICE_TABLE(of, nxp_ldb_match);
+
+static struct platform_driver nxp_ldb_driver = {
+	.probe	= nxp_ldb_probe,
+	.remove	= nxp_ldb_remove,
+	.driver		= {
+		.name		= "nxp-ldb",
+		.of_match_table	= nxp_ldb_match,
+	},
+};
+module_platform_driver(nxp_ldb_driver);
+
+MODULE_AUTHOR("Marek Vasut <[email protected]>");
+MODULE_DESCRIPTION("NXP i.MX8M LDB");
+MODULE_LICENSE("GPL");

Signature · 1 line

2.35.1

The i.MX8MP contains two syscon registers which are responsible for configuring the on-SoC DPI-to-LVDS serializer. Add DT binding which represents this serializer as a bridge.

Signed-off-by Marek Vasut <[email protected]>

Cc Laurent Pinchart <[email protected]>

Cc Lucas Stach <[email protected]>

Cc Maxime Ripard <[email protected]>

Cc Peng Fan <[email protected]>

Cc Rob Herring <[email protected]>

Cc Robby Cai <[email protected]>

Cc Robert Foss <[email protected]>

Cc Sam Ravnborg <[email protected]>

Cc Thomas Zimmermann <[email protected]>

Cc [email protected]

To: [email protected]

---
V2: - Consistently use fsl,imx8mp-ldb as compatible
- Drop items: from compatible:
- Replace minItems with maxItems in clocks:
- Drop quotes from clock-names const: ldb
- Rename syscon to fsl,syscon
- Use generic name of ldb-lvds in example

---
 .../bindings/display/bridge/nxp,ldb.yaml      | 96 +++++++++++++++++++
 1 file changed, 96 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/nxp,ldb.yaml

Documentation/devicetree/bindings/display/bridge/nxp,ldb.yaml new file +96 -0

new file mode 100644
index 0000000000000..f3182566eb316
@@ -0,0 +1,96 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/nxp,ldb.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX8M DPI to LVDS bridge chip
+
+maintainers:
+  - Marek Vasut <[email protected]>
+
+description: |
+  The i.MX8MP contains two syscon registers which are responsible
+  for configuring the on-SoC DPI-to-LVDS serializer. This describes
+  those registers as bridge within the DT.
+
+properties:
+  compatible:
+    const: fsl,imx8mp-ldb
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: ldb
+
+  fsl,syscon:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: A phandle to media block controller.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for DPI input.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for LVDS Channel-A output (panel or bridge).
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for LVDS Channel-B output (panel or bridge).
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - clocks
+  - fsl,syscon
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/imx8mp-clock.h>
+
+    bridge {
+        compatible = "fsl,imx8mp-ldb";
+        clocks = <&clk IMX8MP_CLK_MEDIA_LDB>;
+        clock-names = "ldb";
+        fsl,syscon = <&media_blk_ctrl>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+
+                ldb_from_lcdif2: endpoint {
+                    remote-endpoint = <&lcdif2_to_ldb>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+
+                ldb_lvds_ch0: endpoint {
+                    remote-endpoint = <&ldb_to_lvdsx4panel>;
+                };
+            };
+
+            port@2 {
+                reg = <2>;
+
+                ldb_lvds_ch1: endpoint {
+                };
+            };
+        };
+    };

Signature · 1 line

2.35.1

The i.MX8MP contains two syscon registers which are responsible

for configuring the on-SoC DPI-to-LVDS serializer. Add DT binding which represents this serializer as a bridge.

Signed-off-by Marek Vasut <[email protected]>

Cc Laurent Pinchart <[email protected]>

Cc Lucas Stach <[email protected]>

Cc Maxime Ripard <[email protected]>

Cc Peng Fan <[email protected]>

Cc Rob Herring <[email protected]>

Cc Robby Cai <[email protected]>

Cc Robert Foss <[email protected]>

Cc Sam Ravnborg <[email protected]>

Cc Thomas Zimmermann <[email protected]>

Cc [email protected]

To: [email protected]
---
V2: - Consistently use fsl,imx8mp-ldb as compatible
- Drop items: from compatible:
- Replace minItems with maxItems in clocks:
- Drop quotes from clock-names const: ldb
- Rename syscon to fsl,syscon
- Use generic name of ldb-lvds in example

---
 .../bindings/display/bridge/nxp,ldb.yaml      | 96 +++++++++++++++++++
 1 file changed, 96 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/nxp,ldb.yaml

Documentation/devicetree/bindings/display/bridge/nxp,ldb.yaml new file +0 -0

new file mode 100644
index 0000000000000..f3182566eb316

Documentation/devicetree/bindings/display/bridge/nxp,ldb.yaml new file +77 -0

+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: ldb
+
+  fsl,syscon:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: A phandle to media block controller.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for DPI input.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for LVDS Channel-A output (panel or bridge).
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for LVDS Channel-B output (panel or bridge).
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - clocks
+  - fsl,syscon
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/imx8mp-clock.h>
+
+    bridge {
+        compatible = "fsl,imx8mp-ldb";
+        clocks = <&clk IMX8MP_CLK_MEDIA_LDB>;
+        clock-names = "ldb";
+        fsl,syscon = <&media_blk_ctrl>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+
+                ldb_from_lcdif2: endpoint {
+                    remote-endpoint = <&lcdif2_to_ldb>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+
+                ldb_lvds_ch0: endpoint {
+                    remote-endpoint = <&ldb_to_lvdsx4panel>;
+                };
+            };
+
+            port@2 {
+                reg = <2>;
+
+                ldb_lvds_ch1: endpoint {
+                };
+            };
+        };
+    };

Signature · 1 line

2.35.1

Hi Marek, I read the patch once more.

Quoted 1 line · Marek Vasut

The i.MX8MP contains two syscon registers which are responsible

Here it says i.MX8MP