Skip to contentSkip to conversation

dt-bindings: display: bridge: lt9211: Add Lontium LT9211 bridge driver

PATCH Applied Marek Vasut 2 participants 3 messages Apr 19, 2022

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 dt-bindings: display: bridge: lt9211: Add Lontium LT9211 bridge driver

Add bindings for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly capable at converting formats, but sadly it is also highly undocumented.

Cc Laurent Pinchart <[email protected]>
Cc Lucas Stach <[email protected]>
Cc Maxime Ripard <[email protected]>
Cc Rob Herring <[email protected]>
Cc Robert Foss <[email protected]>
Cc Sam Ravnborg <[email protected]>
Cc Thomas Zimmermann <[email protected]>

To: [email protected]
---
V2: - Fix up s@i2c10@i2c@ in binding example
- Add RB from Rob

---
 .../display/bridge/lontium,lt9211.yaml        | 117 ++++++++++++++++++
 1 file changed, 117 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/lontium,lt9211.yaml
Documentation/devicetree/bindings/display/bridge/lontium,lt9211.yaml new file +117 -0
new file mode 100644
index 0000000000000..9a6e9b25d14a9
@@ -0,0 +1,117 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/lontium,lt9211.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lontium LT9211 DSI/LVDS/DPI to DSI/LVDS/DPI bridge.
+
+maintainers:
+  - Marek Vasut <[email protected]>
+
+description: |
+  The LT9211 are bridge devices which convert Single/Dual-Link DSI/LVDS
+  or Single DPI to Single/Dual-Link DSI/LVDS or Single DPI.
+
+properties:
+  compatible:
+    enum:
+      - lontium,lt9211
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO connected to active high RESET pin.
+
+  vccio-supply:
+    description: Regulator for 1.8V IO power.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Primary MIPI DSI port-1 for MIPI input or
+          LVDS port-1 for LVDS input or DPI input.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Additional MIPI port-2 for MIPI input or LVDS port-2
+          for LVDS input. Used in combination with primary
+          port-1 to drive higher resolution displays
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Primary MIPI DSI port-1 for MIPI output or
+          LVDS port-1 for LVDS output or DPI output.
+
+      port@3:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Additional MIPI port-2 for MIPI output or LVDS port-2
+          for LVDS output. Used in combination with primary
+          port-1 to drive higher resolution displays.
+
+    required:
+      - port@0
+      - port@2
+
+required:
+  - compatible
+  - reg
+  - vccio-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      hdmi-bridge@3b {
+        compatible = "lontium,lt9211";
+        reg = <0x3b>;
+
+        reset-gpios = <&tlmm 128 GPIO_ACTIVE_HIGH>;
+        interrupts-extended = <&tlmm 84 IRQ_TYPE_EDGE_FALLING>;
+
+        vccio-supply = <&lt9211_1v8>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+
+            endpoint {
+              remote-endpoint = <&dsi0_out>;
+            };
+          };
+
+          port@2 {
+            reg = <2>;
+
+            endpoint {
+              remote-endpoint = <&panel_in_lvds>;
+            };
+          };
+        };
+      };
+    };
+
+...
Signature · 1 line
2.35.1
#1 lore raw

PATCH v2 2/2 drm/bridge: lt9211: Add Lontium LT9211 bridge driver

Add driver for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly capable at converting formats, but sadly it is also highly undocumented.

This driver is written without any documentation from Lontium and based only on shreds of information available in various obscure example codes, hence long runs of unknown register patches and lengthy delays in various places. Whichever register meaning could be divined from its behavior has at least a comment around it.

Currently the only mode tested is Single-link DSI to Single-link LVDS. Dual-link LVDS might work as well, the register programming is in place, but is untested.

Cc Laurent Pinchart <[email protected]>
Cc Lucas Stach <[email protected]>
Cc Maxime Ripard <[email protected]>
Cc Robert Foss <[email protected]>
Cc Sam Ravnborg <[email protected]>
Cc Thomas Zimmermann <[email protected]>

To: [email protected]
---
V2: - Add RB from Robert

---
 drivers/gpu/drm/bridge/Kconfig          |  13 +
 drivers/gpu/drm/bridge/Makefile         |   1 +
 drivers/gpu/drm/bridge/lontium-lt9211.c | 802 ++++++++++++++++++++++++
 3 files changed, 816 insertions(+)
 create mode 100644 drivers/gpu/drm/bridge/lontium-lt9211.c
drivers/gpu/drm/bridge/Kconfig +13 -0
index ca70f03ef7405..20f9bc7f4be54 100644
@@ -100,6 +100,19 @@ config DRM_LONTIUM_LT8912B
 	  Say M here if you want to support this hardware as a module.
 	  The module will be named "lontium-lt8912b".
 
+config DRM_LONTIUM_LT9211
+	tristate "Lontium LT9211 DSI/LVDS/DPI bridge"
+	depends on OF
+	select DRM_PANEL_BRIDGE
+	select DRM_KMS_HELPER
+	select DRM_MIPI_DSI
+	select REGMAP_I2C
+	help
+	  Driver for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI
+	  input to Single-link/Dual-Link DSI/LVDS or Single DPI output bridge
+	  chip.
+	  Please say Y if you have such hardware.
+
 config DRM_LONTIUM_LT9611
 	tristate "Lontium LT9611 DSI/HDMI bridge"
 	select SND_SOC_HDMI_CODEC if SND_SOC
drivers/gpu/drm/bridge/Makefile +1 -0
index c90fdf1d1d251..bdffad2a7ed3a 100644
@@ -6,6 +6,7 @@ obj-$(CONFIG_DRM_CROS_EC_ANX7688) += cros-ec-anx7688.o
 obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o
 obj-$(CONFIG_DRM_ITE_IT6505) += ite-it6505.o
 obj-$(CONFIG_DRM_LONTIUM_LT8912B) += lontium-lt8912b.o
+obj-$(CONFIG_DRM_LONTIUM_LT9211) += lontium-lt9211.o
 obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o
 obj-$(CONFIG_DRM_LONTIUM_LT9611UXC) += lontium-lt9611uxc.o
 obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o
drivers/gpu/drm/bridge/lontium-lt9211.c new file +802 -0

802 lines not on this page · raw message

Signature · 1 line
2.35.1
Applied
#2 lore raw
In reply to Marek Vasut
Quoted 137 lines · Marek Vasut

Add bindings for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly capable at converting formats, but sadly it is also highly undocumented.

Cc Laurent Pinchart <[email protected]>
Cc Lucas Stach <[email protected]>
Cc Maxime Ripard <[email protected]>
Cc Rob Herring <[email protected]>
Cc Robert Foss <[email protected]>
Cc Sam Ravnborg <[email protected]>
Cc Thomas Zimmermann <[email protected]>

To: [email protected]
---
V2: - Fix up s@i2c10@i2c@ in binding example
- Add RB from Rob

---
 .../display/bridge/lontium,lt9211.yaml        | 117 ++++++++++++++++++
 1 file changed, 117 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/lontium,lt9211.yaml
Documentation/devicetree/bindings/display/bridge/lontium,lt9211.yaml new file +107 -0
new file mode 100644
index 0000000000000..9a6e9b25d14a9
@@ -0,0 +1,117 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/lontium,lt9211.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lontium LT9211 DSI/LVDS/DPI to DSI/LVDS/DPI bridge.
+
+maintainers:
+  - Marek Vasut <[email protected]>
+
+description: |
+  The LT9211 are bridge devices which convert Single/Dual-Link DSI/LVDS
+  or Single DPI to Single/Dual-Link DSI/LVDS or Single DPI.
+
+properties:
+  compatible:
+    enum:
+      - lontium,lt9211
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO connected to active high RESET pin.
+
+  vccio-supply:
+    description: Regulator for 1.8V IO power.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Primary MIPI DSI port-1 for MIPI input or
+          LVDS port-1 for LVDS input or DPI input.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Additional MIPI port-2 for MIPI input or LVDS port-2
+          for LVDS input. Used in combination with primary
+          port-1 to drive higher resolution displays
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Primary MIPI DSI port-1 for MIPI output or
+          LVDS port-1 for LVDS output or DPI output.
+
+      port@3:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Additional MIPI port-2 for MIPI output or LVDS port-2
+          for LVDS output. Used in combination with primary
+          port-1 to drive higher resolution displays.
+
+    required:
+      - port@0
+      - port@2
+
+required:
+  - compatible
+  - reg
+  - vccio-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      hdmi-bridge@3b {
+        compatible = "lontium,lt9211";
+        reg = <0x3b>;
+
+        reset-gpios = <&tlmm 128 GPIO_ACTIVE_HIGH>;
+        interrupts-extended = <&tlmm 84 IRQ_TYPE_EDGE_FALLING>;
+
+        vccio-supply = <&lt9211_1v8>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+
+            endpoint {
+              remote-endpoint = <&dsi0_out>;
+            };
+          };
+
+          port@2 {
+            reg = <2>;

Documentation/devicetree/bindings/display/bridge/lontium,lt9211.yaml line 117

Quoted 10 lines
Documentation/devicetree/bindings/display/bridge/lontium,lt9211.yaml new file +10 -0
+
+            endpoint {
+              remote-endpoint = <&panel_in_lvds>;
+            };
+          };
+        };
+      };
+    };
+
+...

Applied series to drm-misc-next

Rob.