Add q 12MHz internal clock rate to calculate
Subsystems (2)
v3 cover Add q 12MHz internal clock rate to calculate
1.Added 12Mhz as the clock source for calculating baud rate.
2.Added S4 SOC compatibility.
Yu Tu (2):
tty: serial: meson: Add a 12MHz internal clock rate to calculate baud
rate in order to meet the baud rate requirements of special BT modules
tty: serial: meson: Added S4 SOC compatibility
V1 -> V2: Change format as discussed in the email. V2 -> V3: Change format as discussed in the email.
drivers/tty/serial/meson_uart.c | 25 +++++++++++++++++++++++-- 1 file changed, 23 insertions(+), 2 deletions(-)
base-commit: 05fe70dd2efd13de700c2dfe5169d3a7a5050bc2
Signature · 1 line
2.33.1
PATCH v3 1/2 tty: serial: meson: Add a 12MHz internal clock rate to calculate baud rate in order to meet the baud rate requirements of special BT modules
A /2 divider over XTAL was introduced since G12A, and is preferred to be used over the still present /3 divider since it provides much closer frequencies vs the request baudrate. Especially the BT module uses 3Mhz baud rate. 8Mhz calculations can lead to baud rate bias, causing some problems.
--- drivers/tty/serial/meson_uart.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-)
drivers/tty/serial/meson_uart.c +15 -2
@@ -68,6 +68,7 @@#define AML_UART_BAUD_MASK 0x7fffff#define AML_UART_BAUD_USE BIT(23)#define AML_UART_BAUD_XTAL BIT(24) +#define AML_UART_BAUD_XTAL_DIV2 BIT(27)#define AML_UART_PORT_NUM 12#define AML_UART_PORT_OFFSET 6
@@ -80,6 +81,10 @@ static struct uart_driver meson_uart_driver;static struct uart_port *meson_ports[AML_UART_PORT_NUM ]; +struct meson_uart_data { +bool has_xtal_div2; +}; +static void meson_uart_set_mctrl (struct uart_port *port,unsigned int mctrl) { }
@@ -293,13 +298,20 @@ static int meson_uart_startup(struct uart_port *port)static void meson_uart_change_speed (struct uart_port *port,unsigned long baud) { -u32 val; +const struct meson_uart_data *private_data = port->private_data; +u32 val =0 ;while (!meson_uart_tx_empty (port))cpu_relax ();if (port->uartclk ==24000000 ) { - val =DIV_ROUND_CLOSEST (port->uartclk /3 , baud) -1 ; +unsigned int xtal_div =3 ; + +if (private_data && private_data->has_xtal_div2) { + xtal_div =2 ; + val |=AML_UART_BAUD_XTAL_DIV2 ; + } + val |=DIV_ROUND_CLOSEST (port->uartclk / xtal_div, baud) -1 ; val |=AML_UART_BAUD_XTAL ; }else { val =DIV_ROUND_CLOSEST (port->uartclk /4 , baud) -1 ;
@@ -749,6 +761,7 @@ static int meson_uart_probe(struct platform_device *pdev) port->x_char =0 ; port->ops = &meson_uart_ops; port->fifosize = fifosize; + port->private_data = (void *)device_get_match_data (&pdev->dev); meson_ports[pdev->id] = port;platform_set_drvdata (pdev, port);
Signature · 1 line
2.33.1
Re: [PATCH V3 1/2] tty: serial: meson: Add a 12MHz internal clock rate to calculate baud rate in order to meet the baud rate requirements of special BT modules
Quoted 58 lines · Yu Tu
A /2 divider over XTAL was introduced since G12A, and is preferred to be used over the still present /3 divider since it provides much closer frequencies vs the request baudrate. Especially the BT module uses 3Mhz baud rate. 8Mhz calculations can lead to baud rate bias, causing some problems.
Signed-off-by Yu Tu <[email protected]>--- drivers/tty/serial/meson_uart.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-)drivers/tty/serial/meson_uart.c +14
-2@@ -68,6 +68,7 @@#define AML_UART_BAUD_MASK 0x7fffff#define AML_UART_BAUD_USE BIT(23)#define AML_UART_BAUD_XTAL BIT(24) +#define AML_UART_BAUD_XTAL_DIV2 BIT(27)#define AML_UART_PORT_NUM 12#define AML_UART_PORT_OFFSET 6@@ -80,6 +81,10 @@ static struct uart_driver meson_uart_driver;static struct uart_port *meson_ports[AML_UART_PORT_NUM ]; +struct meson_uart_data { +bool has_xtal_div2; +}; +static void meson_uart_set_mctrl (struct uart_port *port,unsigned int mctrl) { }@@ -293,13 +298,20 @@ static int meson_uart_startup(struct uart_port *port)static void meson_uart_change_speed (struct uart_port *port,unsigned long baud) { -u32 val; +const struct meson_uart_data *private_data = port->private_data; +u32 val =0 ;while (!meson_uart_tx_empty (port))cpu_relax ();if (port->uartclk ==24000000 ) { - val =DIV_ROUND_CLOSEST (port->uartclk /3 , baud) -1 ; +unsigned int xtal_div =3 ; + +if (private_data && private_data->has_xtal_div2) { + xtal_div =2 ; + val |=AML_UART_BAUD_XTAL_DIV2 ; + } + val |=DIV_ROUND_CLOSEST (port->uartclk / xtal_div, baud) -1 ; val |=AML_UART_BAUD_XTAL ; }else { val =DIV_ROUND_CLOSEST (port->uartclk /4 , baud) -1 ;
drivers/tty/serial/meson_uart.c static int meson_uart_probe(struct platform_device *pdev) · line 767
Quoted 7 lines
drivers/tty/serial/meson_uart.c +1
-0@@ -749,6 +761,7 @@ static int meson_uart_probe(struct platform_device *pdev) port->x_char =0 ; port->ops = &meson_uart_ops; port->fifosize = fifosize; + port->private_data = (void *)device_get_match_data (&pdev->dev); meson_ports[pdev->id] = port;platform_set_drvdata (pdev, port);
PATCH v3 2/2 tty: serial: meson: Added S4 SOC compatibility
In reply to Yu TuMake UART driver compatible with S4 SOC UART. Meanwhile, the S4 SOC UART uses 12MHz as the clock source for baud rate calculations.
--- drivers/tty/serial/meson_uart.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/tty/serial/meson_uart.c +8 -0
@@ -790,11 +790,19 @@ static int meson_uart_remove(struct platform_device *pdev)return 0 ; } +static struct meson_uart_data s4_uart_data = { + .has_xtal_div2 = true, +}; +static const struct of_device_id meson_uart_dt_match[] = { { .compatible ="amlogic,meson6-uart" }, { .compatible ="amlogic,meson8-uart" }, { .compatible ="amlogic,meson8b-uart" }, { .compatible ="amlogic,meson-gx-uart" }, + { + .compatible ="amlogic,meson-s4-uart" , + .data = (void *)&s4_uart_data, + }, {/* sentinel */ }, };MODULE_DEVICE_TABLE (of, meson_uart_dt_match);
Signature · 1 line
2.33.1
Re: [PATCH V3 2/2] tty: serial: meson: Added S4 SOC compatibility
Quoted 22 lines · Yu Tu
Make UART driver compatible with S4 SOC UART. Meanwhile, the S4 SOC UART uses 12MHz as the clock source for baud rate calculations.
Signed-off-by Yu Tu <[email protected]>--- drivers/tty/serial/meson_uart.c | 8 ++++++++ 1 file changed, 8 insertions(+)drivers/tty/serial/meson_uart.c +4
-0@@ -790,11 +790,19 @@ static int meson_uart_remove(struct platform_device *pdev)return 0 ; } +static struct meson_uart_data s4_uart_data = { + .has_xtal_div2 = true, +}; +static const struct of_device_id meson_uart_dt_match[] = { { .compatible ="amlogic,meson6-uart" },
drivers/tty/serial/meson_uart.c static int meson_uart_remove(struct platform_device *pdev) · line 808
Quoted 10 lines
drivers/tty/serial/meson_uart.c +4
-0{ .compatible = "amlogic,meson8-uart" }, { .compatible = "amlogic,meson8b-uart" }, { .compatible = "amlogic,meson-gx-uart" }, + { + .compatible = "amlogic,meson-s4-uart", + .data = (void *)&s4_uart_data, + }, { /* sentinel */ }, };MODULE_DEVICE_TABLE (of, meson_uart_dt_match);
Quoted 14 lines · Yu Tu
1.Added 12Mhz as the clock source for calculating baud rate.
2.Added S4 SOC compatibility.
Yu Tu (2):
tty: serial: meson: Add a 12MHz internal clock rate to calculate baud
rate in order to meet the baud rate requirements of special BT modules
tty: serial: meson: Added S4 SOC compatibilityV1 -> V2: Change format as discussed in the email. V2 -> V3: Change format as discussed in the email.
Quoted 7 lines
drivers/tty/serial/meson_uart.c | 25 +++++++++++++++++++++++-- 1 file changed, 23 insertions(+), 2 deletions(-)base-commit:
05fe70dd2efd13de700c2dfe5169d3a7a5050bc2
Thanks for this v3, all fine for me !
Neil