spi: add support for Mediatek SPI-NAND controller
Subsystems (6)
v6 cover spi: add support for Mediatek SPI-NAND controller
Mediatek has an extended version of their NAND Flash Interface which has a SPI-NAND mode. In this mode, the controller can perform 1-bit spi-mem ops for up-to 0xa0 bytes and typical SPI-NAND single, dual and quad IO page cache ops with 2-byte address. Additionally, the page cache ops can be performed with ECC and auto data formatting using the ECC engine of the controller.
This patchset implements support of this mode as a separated SPI-MEM driver with pipelined ECC engine.
Changes since v1:
add a blank line between properties in dt binding doc
rename ecc-engine to nand-ecc-engine for the generic properties
fix warnings/errors from the CI
Changes since v2:
use streamed DMA api to avoid an extra memory copy during read make ECC engine config a per-nand context
take user-requested ECC strength into account
Change since v3:
fix a missed ecc-engine rename in doc from v1
Changes since v4:
fix typo: piplined -> pipelined
fix missing OOB write in snfi driver print page format with dev_dbg instead replace uint*_t copied from vendor driver with u*
Changes since v5:
add missing nfi mode register configuration in probe fix an off-by-one bug in mtk_snand_mac_io
Chuanhong Guo (5):
mtd: nand: make mtk_ecc.c a separated module
spi: add driver for MTK SPI NAND Flash Interface
mtd: nand: mtk-ecc: also parse nand-ecc-engine if available
spi: dt-bindings: add binding doc for spi-mtk-snfi
arm64: dts: mediatek: add mtk-snfi for mt7622
.../bindings/spi/mediatek,spi-mtk-snfi.yaml | 88 +
arch/arm64/boot/dts/mediatek/mt7622.dtsi | 12 +
drivers/mtd/nand/Kconfig | 7 +
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/{raw/mtk_ecc.c => ecc-mtk.c} | 8 +-
drivers/mtd/nand/raw/Kconfig | 1 +
drivers/mtd/nand/raw/Makefile | 2 +-
drivers/mtd/nand/raw/mtk_nand.c | 2 +-
drivers/spi/Kconfig | 10 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-mtk-snfi.c | 1470 +++++++++++++++++
.../linux/mtd/nand-ecc-mtk.h | 0
12 files changed, 1597 insertions(+), 5 deletions(-)
create mode 100644 Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
rename drivers/mtd/nand/{raw/mtk_ecc.c => ecc-mtk.c} (98%)
create mode 100644 drivers/spi/spi-mtk-snfi.c
rename drivers/mtd/nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h (100%)Signature · 1 line
2.35.1
PATCH v6 1/5 mtd: nand: make mtk_ecc.c a separated module
this code will be used in mediatek snfi spi-mem controller with pipelined ECC engine.
---
Change since v1:
actually make it a module instead of a part of nandcore.o
Change in v2-v6: None
drivers/mtd/nand/Kconfig | 7 +++++++
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/{raw/mtk_ecc.c => ecc-mtk.c} | 3 +--
drivers/mtd/nand/raw/Kconfig | 1 +
drivers/mtd/nand/raw/Makefile | 2 +-
drivers/mtd/nand/raw/mtk_nand.c | 2 +-
.../nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h | 0
7 files changed, 12 insertions(+), 4 deletions(-)
rename drivers/mtd/nand/{raw/mtk_ecc.c => ecc-mtk.c} (99%)
rename drivers/mtd/nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h (100%)drivers/mtd/nand/Kconfig +7 -0
@@ -53,6 +53,13 @@ config MTD_NAND_ECC_MXIC help This enables support for the hardware ECC engine from Macronix. +config MTD_NAND_ECC_MEDIATEK + tristate "Mediatek hardware ECC engine" + depends on HAS_IOMEM + select MTD_NAND_ECC + help + This enables support for the hardware ECC engine from Mediatek. + endmenu endmenu
drivers/mtd/nand/Makefile +1 -0
@@ -2,6 +2,7 @@ nandcore-objs := core.o bbt.o obj-$(CONFIG_MTD_NAND_CORE) += nandcore.o +obj-$(CONFIG_MTD_NAND_ECC_MEDIATEK) += ecc-mtk.o obj-y += onenand/ obj-y += raw/
drivers/mtd/nand/ecc-mtk.c renamed from drivers/mtd/nand/raw/mtk_ecc.c +1 -2
@@ -15,8 +15,7 @@#include <linux/of.h> #include <linux/of_platform.h> #include <linux/mutex.h> - -#include "mtk_ecc.h" +#include <linux/mtd/nand-ecc-mtk.h> #define ECC_IDLE_MASK BIT(0)#define ECC_IRQ_EN BIT(0)
drivers/mtd/nand/raw/Kconfig +1 -0
@@ -374,6 +374,7 @@ config MTD_NAND_QCOM config MTD_NAND_MTK tristate "MTK NAND controller" + depends on MTD_NAND_ECC_MEDIATEK depends on ARCH_MEDIATEK || COMPILE_TEST depends on HAS_IOMEM help
drivers/mtd/nand/raw/Makefile +1 -1
@@ -48,7 +48,7 @@ obj-$(CONFIG_MTD_NAND_SUNXI) += sunxi_nand.o obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand/ obj-$(CONFIG_MTD_NAND_QCOM) += qcom_nandc.o -obj-$(CONFIG_MTD_NAND_MTK) += mtk_ecc.o mtk_nand.o +obj-$(CONFIG_MTD_NAND_MTK) += mtk_nand.o obj-$(CONFIG_MTD_NAND_MXIC) += mxic_nand.o obj-$(CONFIG_MTD_NAND_TEGRA) += tegra_nand.o obj-$(CONFIG_MTD_NAND_STM32_FMC2) += stm32_fmc2_nand.o
drivers/mtd/nand/raw/mtk_nand.c +1 -1
@@ -17,7 +17,7 @@#include <linux/iopoll.h> #include <linux/of.h> #include <linux/of_device.h> -#include "mtk_ecc.h" +#include <linux/mtd/nand-ecc-mtk.h> /* NAND controller register definition */ #define NFI_CNFG (0x00)
include/linux/mtd/nand-ecc-mtk.h renamed from drivers/mtd/nand/raw/mtk_ecc.h +0 -0
Signature · 1 line
2.35.1
PATCH v6 2/5 spi: add driver for MTK SPI NAND Flash Interface
In reply to Chuanhong GuoThis driver implements support for the SPI-NAND mode of MTK NAND Flash Interface as a SPI-MEM controller with pipelined ECC capability.
---
Change since v1:
fix CI warnings
Changes since v2:
use streamed DMA api to avoid an extra memory copy during read make ECC engine config a per-nand context
take user-requested ECC strength into account
Change since v3: none
Changes since v4:
fix missing OOB write
print page format with dev_dbg
replace uint*_t copied from vendor driver with u*
Changes since v5:
add missing nfi mode register configuration in probe fix an off-by-one bug in mtk_snand_mac_io
drivers/spi/Kconfig | 10 + drivers/spi/Makefile | 1 + drivers/spi/spi-mtk-snfi.c | 1470 ++++++++++++++++++++++++++++++++++++ 3 files changed, 1481 insertions(+) create mode 100644 drivers/spi/spi-mtk-snfi.c
drivers/spi/Kconfig +10 -0
@@ -590,6 +590,16 @@ config SPI_MTK_NOR SPI interface as well as several SPI NOR specific instructions via SPI MEM interface. +config SPI_MTK_SNFI + tristate "MediaTek SPI NAND Flash Interface" + depends on ARCH_MEDIATEK || COMPILE_TEST + depends on MTD_NAND_ECC_MEDIATEK + help + This enables support for SPI-NAND mode on the MediaTek NAND + Flash Interface found on MediaTek ARM SoCs. This controller + is implemented as a SPI-MEM controller with pipelined ECC + capcability. + config SPI_NPCM_FIU tristate "Nuvoton NPCM FLASH Interface Unit" depends on ARCH_NPCM || COMPILE_TEST
drivers/spi/Makefile +1 -0
@@ -76,6 +76,7 @@ obj-$(CONFIG_SPI_MPC52xx) += spi-mpc52xx.o obj-$(CONFIG_SPI_MT65XX) += spi-mt65xx.o obj-$(CONFIG_SPI_MT7621) += spi-mt7621.o obj-$(CONFIG_SPI_MTK_NOR) += spi-mtk-nor.o +obj-$(CONFIG_SPI_MTK_SNFI) += spi-mtk-snfi.o obj-$(CONFIG_SPI_MXIC) += spi-mxic.o obj-$(CONFIG_SPI_MXS) += spi-mxs.o obj-$(CONFIG_SPI_NPCM_FIU) += spi-npcm-fiu.o
drivers/spi/spi-mtk-snfi.c new file +1470 -0
1,470 lines not on this page · raw message
Signature · 1 line
2.35.1
PATCH v6 3/5 mtd: nand: mtk-ecc: also parse nand-ecc-engine if available
In reply to Chuanhong GuoThe recently added ECC engine support introduced a generic property named nand-ecc-engine for ecc engine phandle. This patch adds support for this new property.
---
Change since v1:
new patch
Change in v2-v6: None
drivers/mtd/nand/ecc-mtk.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/mtd/nand/ecc-mtk.c +4 -1
@@ -279,7 +279,10 @@ struct mtk_ecc *of_mtk_ecc_get(struct device_node *of_node)struct mtk_ecc *ecc =NULL ;struct device_node *np; - np =of_parse_phandle (of_node,"ecc-engine" ,0 ); + np =of_parse_phandle (of_node,"nand-ecc-engine" ,0 ); +/* for backward compatibility */ +if (!np) + np =of_parse_phandle (of_node,"ecc-engine" ,0 );if (np) { ecc =mtk_ecc_get (np);of_node_put (np);
Signature · 1 line
2.35.1
PATCH v6 4/5 spi: dt-bindings: add binding doc for spi-mtk-snfi
In reply to Chuanhong GuoAdd device-tree binding documentation for Mediatek SPI-NAND Flash Interface.
---
Changes since v1:
1. add a blank line between properties in dt binding doc
2. rename ecc-engine to nand-ecc-engine for the generic properties
Change since v2: none
Change since v3: fix a missing rename in v1
Change since v4: fix typo: piplined -> pipelined
Change since v5: none
.../bindings/spi/mediatek,spi-mtk-snfi.yaml | 88 +++++++++++++++++++ 1 file changed, 88 insertions(+) create mode 100644 Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml new file +88 -0
@@ -0,0 +1,88 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/mediatek,spi-mtk-snfi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SPI-NAND flash controller for MediaTek ARM SoCs + +maintainers: + - Chuanhong Guo <[email protected]> + +description: | + The Mediatek SPI-NAND flash controller is an extended version of + the Mediatek NAND flash controller. It can perform standard SPI + instructions with one continuous write and one read for up-to 0xa0 + bytes. It also supports typical SPI-NAND page cache operations + in single, dual or quad IO mode with pipelined ECC encoding/decoding + using the accompanying ECC engine. There should be only one spi + slave device following generic spi bindings. + +allOf: + - $ref: /schemas/spi/spi-controller.yaml# + +properties: + compatible: + enum: + - mediatek,mt7622-snand + - mediatek,mt7629-snand + + reg: + items: + - description: core registers + + interrupts: + items: + - description: NFI interrupt + + clocks: + items: + - description: clock used for the controller + - description: clock used for the SPI bus + + clock-names: + items: + - const: nfi_clk + - const: pad_clk + + nand-ecc-engine: + description: device-tree node of the accompanying ECC engine. + $ref: /schemas/types.yaml#/definitions/phandle + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - nand-ecc-engine + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/mt7622-clk.h> + soc { + #address-cells = <2>; + #size-cells = <2>; + snfi: spi@1100d000 { + compatible = "mediatek,mt7622-snand"; + reg = <0 0x1100d000 0 0x1000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI_PD>, <&pericfg CLK_PERI_SNFI_PD>; + clock-names = "nfi_clk", "pad_clk"; + nand-ecc-engine = <&bch>; + #address-cells = <1>; + #size-cells = <0>; + + flash@0 { + compatible = "spi-nand"; + reg = <0>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + nand-ecc-engine = <&snfi>; + }; + }; + };
Signature · 1 line
2.35.1
PATCH v6 5/5 arm64: dts: mediatek: add mtk-snfi for mt7622
In reply to Chuanhong GuoThis patch adds a device-tree node for the MTK SPI-NAND Flash Interface for MT7622 device tree.
---
Changes since v1:
1. use the newly introduced nand-ecc-engine instead
2. reword commit message
Change in v2-v6: none
arch/arm64/boot/dts/mediatek/mt7622.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+)
arch/arm64/boot/dts/mediatek/mt7622.dtsi +12 -0
@@ -545,6 +545,18 @@ nandc: nfi@1100d000 { status = "disabled"; }; + snfi: spi@1100d000 { + compatible = "mediatek,mt7622-snand"; + reg = <0 0x1100d000 0 0x1000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI_PD>, <&pericfg CLK_PERI_SNFI_PD>; + clock-names = "nfi_clk", "pad_clk"; + nand-ecc-engine = <&bch>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + bch: ecc@1100e000 { compatible = "mediatek,mt7622-ecc"; reg = <0 0x1100e000 0 0x1000>;
Signature · 1 line
2.35.1
Re: [PATCH v6 5/5] arm64: dts: mediatek: add mtk-snfi for mt7622
Quoted 4 lines · Chuanhong Guo
This patch adds a device-tree node for the MTK SPI-NAND Flash Interface for MT7622 device tree.
Signed-off-by Chuanhong Guo <[email protected]>
Applied, thanks!
Quoted 22 lines
---
Changes since v1:
1. use the newly introduced nand-ecc-engine instead
2. reword commit message
Change in v2-v6: nonearch/arm64/boot/dts/mediatek/mt7622.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+)arch/arm64/boot/dts/mediatek/mt7622.dtsi +5
-0@@ -545,6 +545,18 @@ nandc: nfi@1100d000 { status = "disabled"; }; + snfi: spi@1100d000 { + compatible = "mediatek,mt7622-snand"; + reg = <0 0x1100d000 0 0x1000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI_PD>, <&pericfg CLK_PERI_SNFI_PD>;
arch/arm64/boot/dts/mediatek/mt7622.dtsi nandc: nfi@1100d000 { · line 562
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt7622.dtsi +7
-0+ clock-names = "nfi_clk", "pad_clk"; + nand-ecc-engine = <&bch>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + bch: ecc@1100e000 { compatible = "mediatek,mt7622-ecc"; reg = <0 0x1100e000 0 0x1000>;
_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
Miquel Raynal
maintainerHi Mark,
[email protected] wrote on Sun, 24 Apr 2022 11:25:22 +0800:
Quoted 9 lines
Mediatek has an extended version of their NAND Flash Interface which has a SPI-NAND mode. In this mode, the controller can perform 1-bit spi-mem ops for up-to
0xa0bytes and typical SPI-NAND single, dual and quad IO page cache ops with 2-byte address. Additionally, the page cache ops can be performed with ECC and auto data formatting using the ECC engine of the controller.This patchset implements support of this mode as a separated SPI-MEM driver with pipelined ECC engine.
[...]
The patch actually look independent, so if it's fine for you I can take the two mtd patches and let you merge the spi/binding changes.
Would this work for you?
Quoted 16 lines
Chuanhong Guo (5):
mtd: nand: makemtk_ecc.ca separated module
spi: add driver for MTK SPI NAND Flash Interface
mtd: nand: mtk-ecc: also parse nand-ecc-engine if available
spi: dt-bindings: add binding doc for spi-mtk-snfi
arm64: dts: mediatek: add mtk-snfi for mt7622.../bindings/spi/mediatek,spi-mtk-snfi.yaml | 88 + arch/arm64/boot/dts/mediatek/mt7622.dtsi | 12 + drivers/mtd/nand/Kconfig | 7 + drivers/mtd/nand/Makefile | 1 + drivers/mtd/nand/{raw/mtk_ecc.c => ecc-mtk.c} | 8 +- drivers/mtd/nand/raw/Kconfig | 1 + drivers/mtd/nand/raw/Makefile | 2 +- drivers/mtd/nand/raw/mtk_nand.c | 2 +- drivers/spi/Kconfig | 10 +
Quoted 9 lines
drivers/spi/Makefile | 1 +
drivers/spi/spi-mtk-snfi.c | 1470 +++++++++++++++++
.../linux/mtd/nand-ecc-mtk.h | 0
12 files changed, 1597 insertions(+), 5 deletions(-)
create mode 100644 Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
rename drivers/mtd/nand/{raw/mtk_ecc.c => ecc-mtk.c} (98%)
create mode 100644 drivers/spi/spi-mtk-snfi.c
rename drivers/mtd/nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h (100%)Thanks,
Miquèl
_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
Mark Brown
maintainerQuoted 4 lines · Miquel Raynal
The patch actually look independent, so if it's fine for you I can take the two mtd patches and let you merge the spi/binding changes.
Would this work for you?
That sounds great.
Hi Miquel!
Quoted 5 lines · Miquel Raynal
[...]
The patch actually look independent, so if it's fine for you I can take the two mtd patches and let you merge the spi/binding changes.
Out of curiosity:
Wouldn't that break the build for spi subsystem? Because...
Quoted 1 line
Quoted 1 line
rename drivers/mtd/nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h (100%)
The spi driver needs this header file which is moved in the mtd patch.
Signature · 2 lines
Regards, Chuanhong Guo
Mark Brown
maintainerQuoted 11 lines · Chuanhong Guo
Quoted 2 lines · Miquel Raynal
The patch actually look independent, so if it's fine for you I can take the two mtd patches and let you merge the spi/binding changes.
Out of curiosity:
Wouldn't that break the build for spi subsystem? Because...Quoted 1 line
Quoted 1 line
rename drivers/mtd/nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h (100%)The spi driver needs this header file which is moved in the mtd patch.
Ah, that'll be an issue indeed - if I could get a signed tag with the dependency in it I can go ahead with the SPI bits?
Miquel Raynal
maintainerHi Mark,
[email protected] wrote on Wed, 27 Apr 2022 15:13:42 +0100:
Quoted 6 lines · Chuanhong Guo
Quoted 4 lines · Miquel Raynal
Quoted 3 lines
The patch actually look independent, so if it's fine for you I can take the two mtd patches and let you merge the spi/binding changes.
Quoted 6 lines
Quoted 6 lines
Out of curiosity:
Wouldn't that break the build for spi subsystem? Because...Quoted 1 line
Quoted 1 line
rename drivers/mtd/nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h (100%)The spi driver needs this header file which is moved in the mtd patch.
Ah, yeah, right.
Quoted 2 lines
Ah, that'll be an issue indeed - if I could get a signed tag with the dependency in it I can go ahead with the SPI bits?
Ok, I'll share an immutable tag.
Thanks,
Miquèl
Miquel Raynal
maintainerHello,
[email protected] wrote on Wed, 27 Apr 2022 15:13:42 +0100:
Quoted 9 lines · Chuanhong Guo
Quoted 7 lines · Miquel Raynal
Quoted 3 lines
The patch actually look independent, so if it's fine for you I can take the two mtd patches and let you merge the spi/binding changes.
Out of curiosity:
Wouldn't that break the build for spi subsystem? Because...
Quoted 6 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
rename drivers/mtd/nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h (100%)The spi driver needs this header file which is moved in the mtd patch.
Ah, that'll be an issue indeed - if I could get a signed tag with the dependency in it I can go ahead with the SPI bits?
I pulled the two patches, here is a tag with these patches for you, Mark.
The following changes since commit 3123109284176b1532874591f7c81f3837bbdc17:
Linux 5.18-rc1 (2022-04-03 14:08:21 -0700)
are available in the Git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git tags/mtd/mtk-spi-nand-for-5.19
for you to fetch changes up to 4c5bf4b51c9857e20c5f5e9d74b86aa1bd1def40:
mtd: nand: mtk-ecc: also parse nand-ecc-engine if available (2022-04-27 18:12:43 +0200)
----------------------------------------------------------------
Mediatek ECC changes:
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
----------------------------------------------------------------
Chuanhong Guo (2):
mtd: nand: make mtk_ecc.c a separated module
mtd: nand: mtk-ecc: also parse nand-ecc-engine if available
drivers/mtd/nand/Kconfig | 7 +++++++
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/{raw/mtk_ecc.c => ecc-mtk.c} | 8 +++++---
drivers/mtd/nand/raw/Kconfig | 1 +
drivers/mtd/nand/raw/Makefile | 2 +-
drivers/mtd/nand/raw/mtk_nand.c | 2 +-
drivers/mtd/nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h | 0
7 files changed, 16 insertions(+), 5 deletions(-)
rename drivers/mtd/nand/{raw/mtk_ecc.c => ecc-mtk.c} (98%)
rename drivers/mtd/nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h (100%)Mark Brown
maintainerRe: (subset) [PATCH v6 0/5] spi: add support for Mediatek SPI-NAND controller
In reply to Chuanhong GuoQuoted 8 lines · Chuanhong Guo
Mediatek has an extended version of their NAND Flash Interface which has a SPI-NAND mode. In this mode, the controller can perform 1-bit spi-mem ops for up-to
0xa0bytes and typical SPI-NAND single, dual and quad IO page cache ops with 2-byte address. Additionally, the page cache ops can be performed with ECC and auto data formatting using the ECC engine of the controller.[...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
Thanks!
[2/5] spi: add driver for MTK SPI NAND Flash Interface
commit: 764f1b7481645b2b4488eda26c4da7f331697e6b
[4/5] spi: dt-bindings: add binding doc for spi-mtk-snfi
commit: 69bb9b29bf67e850beece45e9c99ca707eac7e41All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark