Skip to contentSkip to conversation

i2c: ismt: Provide a DMA buffer for Interrupt Cause Logging

PATCH Applied Mika Westerberg 3 participants 5 messages Apr 27, 2022 – May 23, 2022

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 i2c: ismt: Provide a DMA buffer for Interrupt Cause Logging

Before sending a MSI the hardware writes information pertinent to the interrupt cause to a memory location pointed by SMTICL register. This memory holds three double words where the least significant bit tells whether the interrupt cause of master/target/error is valid. The driver does not use this but we need to set it up because otherwise it will perform DMA write to the default address (0) and this will cause an IOMMU fault such as below:

DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set

To prevent this from happening, provide a proper DMA buffer for this that then gets mapped by the IOMMU accordingly.

---
 drivers/i2c/busses/i2c-ismt.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
drivers/i2c/busses/i2c-ismt.c +14 -0
index c0364314877e..c16157ee8c52 100644
@@ -82,6 +82,7 @@
 
 #define ISMT_DESC_ENTRIES	2	/* number of descriptor entries */
 #define ISMT_MAX_RETRIES	3	/* number of SMBus retries to attempt */
+#define ISMT_LOG_ENTRIES	3	/* number of interrupt cause log entries */
 
 /* Hardware Descriptor Constants - Control Field */
 #define ISMT_DESC_CWRL	0x01	/* Command/Write Length */
@@ -175,6 +176,8 @@ struct ismt_priv {
 	u8 head;				/* ring buffer head pointer */
 	struct completion cmp;			/* interrupt completion */
 	u8 buffer[I2C_SMBUS_BLOCK_MAX + 16];	/* temp R/W data buffer */
+	dma_addr_t log_dma;
+	u32 *log;
 };
 
 static const struct pci_device_id ismt_ids[] = {
@@ -411,6 +414,9 @@ static int ismt_access(struct i2c_adapter *adap, u16 addr,
 	memset(desc, 0, sizeof(struct ismt_desc));
 	desc->tgtaddr_rw = ISMT_DESC_ADDR_RW(addr, read_write);
 
+	/* Always clear the log entries */
+	memset(priv->log, 0, ISMT_LOG_ENTRIES * sizeof(u32));
+
 	/* Initialize common control bits */
 	if (likely(pci_dev_msi_enabled(priv->pci_dev)))
 		desc->control = ISMT_DESC_INT | ISMT_DESC_FAIR;
@@ -708,6 +714,8 @@ static void ismt_hw_init(struct ismt_priv *priv)
 	/* initialize the Master Descriptor Base Address (MDBA) */
 	writeq(priv->io_rng_dma, priv->smba + ISMT_MSTR_MDBA);
 
+	writeq(priv->log_dma, priv->smba + ISMT_GR_SMTICL);
+
 	/* initialize the Master Control Register (MCTRL) */
 	writel(ISMT_MCTRL_MEIE, priv->smba + ISMT_MSTR_MCTRL);
 
@@ -795,6 +803,12 @@ static int ismt_dev_init(struct ismt_priv *priv)
 	priv->head = 0;
 	init_completion(&priv->cmp);
 
+	priv->log = dmam_alloc_coherent(&priv->pci_dev->dev,
+					ISMT_LOG_ENTRIES * sizeof(u32),
+					&priv->log_dma, GFP_KERNEL);
+	if (!priv->log)
+		return -ENOMEM;
+
 	return 0;
 }
 
Signature · 1 line
2.35.1
Reviewed-by on v1 1/1
#1 lore raw
Quoted 8 lines · Mika Westerberg

Before sending a MSI the hardware writes information pertinent to the interrupt cause to a memory location pointed by SMTICL register. This memory holds three double words where the least significant bit tells whether the interrupt cause of master/target/error is valid. The driver does not use this but we need to set it up because otherwise it will perform DMA write to the default address (0) and this will cause an IOMMU fault such as below:

Quoted 6 lines

DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set

To prevent this from happening, provide a proper DMA buffer for this that then gets mapped by the IOMMU accordingly.

Quoted 61 lines
---
 drivers/i2c/busses/i2c-ismt.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
drivers/i2c/busses/i2c-ismt.c +14 -0
index c0364314877e..c16157ee8c52 100644
@@ -82,6 +82,7 @@
 
 #define ISMT_DESC_ENTRIES	2	/* number of descriptor entries */
 #define ISMT_MAX_RETRIES	3	/* number of SMBus retries to attempt */
+#define ISMT_LOG_ENTRIES	3	/* number of interrupt cause log entries */
 
 /* Hardware Descriptor Constants - Control Field */
 #define ISMT_DESC_CWRL	0x01	/* Command/Write Length */
@@ -175,6 +176,8 @@ struct ismt_priv {
 	u8 head;				/* ring buffer head pointer */
 	struct completion cmp;			/* interrupt completion */
 	u8 buffer[I2C_SMBUS_BLOCK_MAX + 16];	/* temp R/W data buffer */
+	dma_addr_t log_dma;
+	u32 *log;
 };
 
 static const struct pci_device_id ismt_ids[] = {
@@ -411,6 +414,9 @@ static int ismt_access(struct i2c_adapter *adap, u16 addr,
 	memset(desc, 0, sizeof(struct ismt_desc));
 	desc->tgtaddr_rw = ISMT_DESC_ADDR_RW(addr, read_write);
 
+	/* Always clear the log entries */
+	memset(priv->log, 0, ISMT_LOG_ENTRIES * sizeof(u32));
+
 	/* Initialize common control bits */
 	if (likely(pci_dev_msi_enabled(priv->pci_dev)))
 		desc->control = ISMT_DESC_INT | ISMT_DESC_FAIR;
@@ -708,6 +714,8 @@ static void ismt_hw_init(struct ismt_priv *priv)
 	/* initialize the Master Descriptor Base Address (MDBA) */
 	writeq(priv->io_rng_dma, priv->smba + ISMT_MSTR_MDBA);
 
+	writeq(priv->log_dma, priv->smba + ISMT_GR_SMTICL);
+
 	/* initialize the Master Control Register (MCTRL) */
 	writel(ISMT_MCTRL_MEIE, priv->smba + ISMT_MSTR_MCTRL);
 
@@ -795,6 +803,12 @@ static int ismt_dev_init(struct ismt_priv *priv)
 	priv->head = 0;
 	init_completion(&priv->cmp);
 
+	priv->log = dmam_alloc_coherent(&priv->pci_dev->dev,
+					ISMT_LOG_ENTRIES * sizeof(u32),
+					&priv->log_dma, GFP_KERNEL);
+	if (!priv->log)
+		return -ENOMEM;
+
 	return 0;
 }
 
Signature · 1 line
2.35.1
Signature · 2 lines
With Best Regards,
Andy Shevchenko
Applied
#2 lore raw
In reply to Mika Westerberg
Quoted 8 lines · Mika Westerberg

Before sending a MSI the hardware writes information pertinent to the interrupt cause to a memory location pointed by SMTICL register. This memory holds three double words where the least significant bit tells whether the interrupt cause of master/target/error is valid. The driver does not use this but we need to set it up because otherwise it will perform DMA write to the default address (0) and this will cause an IOMMU fault such as below:

Quoted 8 lines

DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set

To prevent this from happening, provide a proper DMA buffer for this that then gets mapped by the IOMMU accordingly.

No maintainer response so far, but given this looks like an important bugfix and you guys are all from Intel as well, I'll apply it this time.

Applied to for-current, thanks!

#3 lore raw
Quoted 13 lines · Wolfram Sang
Quoted 12 lines · Mika Westerberg

Before sending a MSI the hardware writes information pertinent to the interrupt cause to a memory location pointed by SMTICL register. This memory holds three double words where the least significant bit tells whether the interrupt cause of master/target/error is valid. The driver does not use this but we need to set it up because otherwise it will perform DMA write to the default address (0) and this will cause an IOMMU fault such as below:

DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set

Quoted 7 lines
Quoted 4 lines

To prevent this from happening, provide a proper DMA buffer for this that then gets mapped by the IOMMU accordingly.

No maintainer response so far, but given this looks like an important bugfix and you guys are all from Intel as well, I'll apply it this time.

It's indeed.

Quoted 1 line

Applied to for-current, thanks!

Thanks, Wolfram!

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#4 lore raw
In reply to Wolfram Sang
Quoted 16 lines · Wolfram Sang
Quoted 15 lines · Mika Westerberg

Before sending a MSI the hardware writes information pertinent to the interrupt cause to a memory location pointed by SMTICL register. This memory holds three double words where the least significant bit tells whether the interrupt cause of master/target/error is valid. The driver does not use this but we need to set it up because otherwise it will perform DMA write to the default address (0) and this will cause an IOMMU fault such as below:

DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set

To prevent this from happening, provide a proper DMA buffer for this that then gets mapped by the IOMMU accordingly.

Quoted 6 lines
Quoted 1 line

No maintainer response so far, but given this looks like an important bugfix and you guys are all from Intel as well, I'll apply it this time.

Applied to for-current, thanks!

Thanks!